1 Temat przez Cezary (edytowany przez Cezary 2016-07-12 11:19:39)

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 109,272

Temat: NDIS/QMI w Gargoyle (GUI)

UWAGA: Podane informacje dotyczą wydania 1.6.x. W nowszych wydaniach modemy obsługiwane są po prostu jako kolejna opcja na liście "wan".

Dlaczego w tym trybie a nie zwykłym? Ponieważ dzięki nim można osiągnąć większe prędkości połączenia niż przy połączeniu przez ppp, co ma znaczenie przy połączeniu np. LTE.

UWAGA: Dla większości routerów niezbędne jest posiadanie dobrego huba USB z własnym zasilaniem. Zwykle modemy potrzebują więcej energii niż jest w stanie dostarczyć złącze USB w routerze. Modem będzie działać bezpośrednio w routerze, ale jak będzie zrywał połączenie, router będzie się resetował itd - potrzebny jest hub z własnym zasilaniem.
UWAGA: Bez wykupienia odpowiedniej opcji dostępnej w niektórych tylko ofertach abonamentowych nie jest możliwy dostęp z sieci komórkowej do naszego routera i usług na nim uruchomionych.

NDIS
(RNDIS, NCM, CDC Ether) np. Huawei E173, E372, E3272, E3276
https://lh5.googleusercontent.com/-0xpRvDo7wYI/Um0_j21bIZI/AAAAAAAABos/3dhP-Io0xnQ/w598-h316-no/Gargoyle+Router+Management+Utility%25283%2529.png

Dla niektórych modemów wymagana jest zmiana mac adresu (pokazana powyżej), prawdopodobnie zależy to od wersji firmware, więc należy sprawdzić czy wymagane jest jego ustawienie.

QMI
np. Huawei E372, E398

https://lh3.googleusercontent.com/-1F8eLZaAHOU/Unz4qqK7MPI/AAAAAAAABps/SuVT3HnshoI/w588-h324-no/Gargoyle+Router+Management+Utility.png

Ta funkcjonalność została włączona do obrazów od wersji 1.5.11.2. Należy zwrócić uwagę na interfejs wan - nie może tam być "Domyślny" (to jest port WAN routera) tylko specyficzny dla modemu - wwan0, usb0 czy podobny.

Nic już nie trzeba ustawiać z konsoli, można ustawić to wszystko w gui. Testowane na Huawei E372 i E173, powinno działać także z E3276. NDIS nie działa z E3131, on wymaga innego sterownika. Funkcjonalnie robi to AT^NDISUP (ndis), więc o ile modem to obsługuje to powinno działać. QMI woła uqmi (jest już w obrazie dla routerów z 8MB flash).
Należy pamiętać o wybraniu wwan0 (lub podobnego) jako interfejsu (nie może być "Domyślny" bo to określa port WAN routera).

Podobnie jak to było ze skryptami
- czasami (na Orange) otrzymuje adres 10.* i nie chce działać
- przy niektórych wersjach firmware modemu trzeba zmienić mac adres (patrz screenshot)
- potrafi się nie uruchomić przy starcie i trzeba jawnie ifup wan robić (lub ustawić monitor połączenia)

Koniecznie jest także uruchomienie monitora połączenia i wybranie akcji jako restart interfejsu wan.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

2 Odpowiedź przez daro33

  • daro33
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2013-03-14
  • Posty: 180

Odp: NDIS/QMI w Gargoyle (GUI)

Witam. Próbowałem ale recznie z konsoli musiałem przestawić option enabled 0 na 1, bez tego modem/e3276/ nie chciał się łączyć na wdr3600. Pomysł ok, dziękuję.

3 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 109,272

Odp: NDIS/QMI w Gargoyle (GUI)

Jak przestawiłeś to włączyłeś stare skrypty. Przestaw znów na 0 i zrób ifup wan. Zobacz później co się dzieje w logach.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

4 Odpowiedź przez daro33 (edytowany przez daro33 2013-10-28 15:48:39)

  • daro33
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2013-03-14
  • Posty: 180

Odp: NDIS/QMI w Gargoyle (GUI)

Jednak nie chce się łączyć

Jan  1 01:00:39 Gargoyle kern.debug kernel: [    0.330000] pci 0000:00:00.0: supports D1
Jan  1 01:00:39 Gargoyle kern.debug kernel: [    0.330000] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
Jan  1 01:00:39 Gargoyle kern.info kernel: [    0.330000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1001ffff 64bit]
Jan  1 01:00:39 Gargoyle kern.info kernel: [    0.340000] pci 0000:00:00.0: BAR 6: assigned [mem 0x10020000-0x1002ffff pref]
Jan  1 01:00:39 Gargoyle kern.info kernel: [    0.340000] pci 0000:00:00.0: using irq 40 for pin 1
Jan  1 01:00:39 Gargoyle kern.info kernel: [    0.350000] Switching to clocksource MIPS
Jan  1 01:00:39 Gargoyle kern.info kernel: [    0.350000] NET: Registered protocol family 2
Jan  1 01:00:39 Gargoyle kern.info kernel: [    0.360000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
Jan  1 01:00:39 Gargoyle kern.info kernel: [    0.360000] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
Jan  1 01:00:39 Gargoyle kern.info kernel: [    0.370000] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
Jan  1 01:00:39 Gargoyle kern.info kernel: [    0.370000] TCP: Hash tables configured (established 4096 bind 4096)
Jan  1 01:00:39 Gargoyle kern.info kernel: [    0.380000] TCP reno registered
Jan  1 01:00:39 Gargoyle kern.info kernel: [    0.380000] UDP hash table entries: 256 (order: 0, 4096 bytes)
Jan  1 01:00:39 Gargoyle kern.info kernel: [    0.390000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
Jan  1 01:00:39 Gargoyle kern.info kernel: [    0.390000] NET: Registered protocol family 1
Jan  1 01:00:39 Gargoyle kern.debug kernel: [    0.400000] PCI: CLS 0 bytes, default 32
Jan  1 01:00:39 Gargoyle kern.info kernel: [    0.410000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
Jan  1 01:00:39 Gargoyle kern.info kernel: [    0.420000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
Jan  1 01:00:39 Gargoyle kern.info kernel: [    0.430000] msgmni has been set to 246
Jan  1 01:00:39 Gargoyle kern.info kernel: [    0.430000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
Jan  1 01:00:39 Gargoyle kern.info kernel: [    0.440000] io scheduler noop registered
Jan  1 01:00:39 Gargoyle kern.info kernel: [    0.440000] io scheduler deadline registered (default)
Jan  1 01:00:39 Gargoyle kern.info kernel: [    0.450000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
Jan  1 01:00:39 Gargoyle kern.info kernel: [    0.480000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
Jan  1 01:00:39 Gargoyle kern.info kernel: [    0.490000] console [ttyS0] enabled, bootconsole disabled
Jan  1 01:00:39 Gargoyle kern.warn kernel: [    0.500000] m25p80 spi0.0: found en25q64, expected m25p80
Jan  1 01:00:39 Gargoyle kern.info kernel: [    0.500000] m25p80 spi0.0: en25q64 (8192 Kbytes)
Jan  1 01:00:39 Gargoyle kern.notice kernel: [    0.510000] 5 tp-link partitions found on MTD device spi0.0
Jan  1 01:00:39 Gargoyle kern.notice kernel: [    0.520000] Creating 5 MTD partitions on "spi0.0":
Jan  1 01:00:39 Gargoyle kern.notice kernel: [    0.520000] 0x000000000000-0x000000020000 : "u-boot"
Jan  1 01:00:39 Gargoyle kern.notice kernel: [    0.530000] 0x000000020000-0x00000010eda0 : "kernel"
Jan  1 01:00:39 Gargoyle kern.warn kernel: [    0.530000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
Jan  1 01:00:39 Gargoyle kern.notice kernel: [    0.550000] 0x00000010eda0-0x0000007f0000 : "rootfs"
Jan  1 01:00:39 Gargoyle kern.warn kernel: [    0.550000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
Jan  1 01:00:39 Gargoyle kern.notice kernel: [    0.570000] mtd: partition "rootfs" set to be root filesystem
Jan  1 01:00:39 Gargoyle kern.info kernel: [    0.570000] mtd: partition "rootfs_data" created automatically, ofs=650000, len=1A0000
Jan  1 01:00:39 Gargoyle kern.notice kernel: [    0.580000] 0x000000650000-0x0000007f0000 : "rootfs_data"
Jan  1 01:00:39 Gargoyle kern.notice kernel: [    0.590000] 0x0000007f0000-0x000000800000 : "art"
Jan  1 01:00:39 Gargoyle kern.notice kernel: [    0.590000] 0x000000020000-0x0000007f0000 : "firmware"
Jan  1 01:00:39 Gargoyle kern.info kernel: [    0.730000] ag71xx_mdio: probed
Jan  1 01:00:39 Gargoyle kern.info kernel: [    0.730000] eth0: Atheros AG71xx at 0xb9000000, irq 4
Jan  1 01:00:39 Gargoyle kern.info kernel: [    1.310000] eth0: Atheros AR8327 switch driver attached.
Jan  1 01:00:39 Gargoyle kern.info kernel: [    2.470000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd033, driver=Atheros AR8216/AR8236/AR8316]
Jan  1 01:00:39 Gargoyle kern.info kernel: [    2.490000] TCP cubic registered
Jan  1 01:00:39 Gargoyle kern.info kernel: [    2.490000] NET: Registered protocol family 17
Jan  1 01:00:39 Gargoyle kern.notice kernel: [    2.490000] Bridge firewalling registered
Jan  1 01:00:39 Gargoyle kern.info kernel: [    2.500000] Ebtables v2.0 registered
Jan  1 01:00:39 Gargoyle kern.info kernel: [    2.500000] 8021q: 802.1Q VLAN Support v1.8
Jan  1 01:00:39 Gargoyle kern.info kernel: [    2.510000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Jan  1 01:00:39 Gargoyle kern.info kernel: [    2.520000] Freeing unused kernel memory: 216k freed
Jan  1 01:00:39 Gargoyle kern.debug kernel: [    4.460000] Registered led device: tp-link:blue:qss
Jan  1 01:00:39 Gargoyle kern.info kernel: [   33.210000] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
Jan  1 01:00:39 Gargoyle kern.info kernel: [   33.310000] ip_tables: (C) 2000-2006 Netfilter Core Team
Jan  1 01:00:39 Gargoyle kern.info kernel: [   33.660000] NET: Registered protocol family 24
Jan  1 01:00:39 Gargoyle kern.info kernel: [   33.790000] nf_conntrack version 0.5.0 (1978 buckets, 7912 max)
Jan  1 01:00:39 Gargoyle kern.info kernel: [   34.220000] PPTP driver version 0.8.5
Jan  1 01:00:39 Gargoyle kern.info kernel: [   34.840000] xt_time: kernel timezone is -0000
Jan  1 01:00:39 Gargoyle kern.info kernel: [   35.540000]     Hooked IMQ after mangle on PREROUTING
Jan  1 01:00:39 Gargoyle kern.info kernel: [   35.550000]     Hooked IMQ after nat on POSTROUTING
Jan  1 01:00:39 Gargoyle kern.info kernel: [   35.550000] IMQ driver loaded successfully. (numdevs = 2, numqueues = 1)
Jan  1 01:00:39 Gargoyle kern.info kernel: [   35.710000] Netfilter messages via NETLINK v0.30.
Jan  1 01:00:39 Gargoyle kern.notice kernel: [   35.910000] ip_set: protocol 6
Jan  1 01:00:39 Gargoyle kern.info kernel: [   36.480000] usbcore: registered new interface driver cdc_acm
Jan  1 01:00:39 Gargoyle kern.info kernel: [   36.480000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
Jan  1 01:00:39 Gargoyle kern.info kernel: [   36.610000] usbcore: registered new interface driver usblp
Jan  1 01:00:39 Gargoyle kern.info kernel: [   36.630000] usbcore: registered new interface driver usbserial
Jan  1 01:00:39 Gargoyle kern.info kernel: [   36.640000] USB Serial support registered for generic
Jan  1 01:00:39 Gargoyle kern.info kernel: [   36.650000] usbcore: registered new interface driver usbserial_generic
Jan  1 01:00:39 Gargoyle kern.info kernel: [   36.650000] usbserial: USB Serial Driver core
Jan  1 01:00:39 Gargoyle kern.info kernel: [   36.730000] USB Serial support registered for Sierra USB modem
Jan  1 01:00:39 Gargoyle kern.info kernel: [   36.740000] usbcore: registered new interface driver sierra
Jan  1 01:00:39 Gargoyle kern.info kernel: [   36.740000] sierra: v.1.7.40:USB Driver for Sierra Wireless USB modems
Jan  1 01:00:39 Gargoyle kern.info kernel: [   36.770000] usbcore: registered new interface driver sierra_net
Jan  1 01:00:39 Gargoyle kern.info kernel: [   36.890000] usbcore: registered new interface driver ums-alauda
Jan  1 01:00:39 Gargoyle kern.info kernel: [   36.920000] usbcore: registered new interface driver ums-cypress
Jan  1 01:00:39 Gargoyle kern.info kernel: [   36.940000] usbcore: registered new interface driver ums-datafab
Jan  1 01:00:39 Gargoyle kern.info kernel: [   37.000000] usbcore: registered new interface driver ums-freecom
Jan  1 01:00:39 Gargoyle kern.info kernel: [   37.020000] usbcore: registered new interface driver ums-isd200
Jan  1 01:00:39 Gargoyle kern.info kernel: [   37.040000] usbcore: registered new interface driver ums-jumpshot
Jan  1 01:00:39 Gargoyle kern.info kernel: [   37.060000] usbcore: registered new interface driver ums-karma
Jan  1 01:00:39 Gargoyle kern.info kernel: [   37.080000] usbcore: registered new interface driver ums-sddr09
Jan  1 01:00:39 Gargoyle kern.info kernel: [   37.110000] usbcore: registered new interface driver ums-sddr55
Jan  1 01:00:39 Gargoyle kern.info kernel: [   37.130000] usbcore: registered new interface driver ums-usbat
Jan  1 01:00:39 Gargoyle kern.info kernel: [   37.210000] usbcore: registered new interface driver cdc_wdm
Jan  1 01:00:39 Gargoyle kern.info kernel: [   37.230000] usbcore: registered new interface driver cdc_ether
Jan  1 01:00:39 Gargoyle kern.info kernel: [   37.270000] usbcore: registered new interface driver cdc_ncm
Jan  1 01:00:39 Gargoyle kern.info kernel: [   37.340000] usbcore: registered new interface driver qmi_wwan
Jan  1 01:00:39 Gargoyle kern.info kernel: [   37.370000] usbcore: registered new interface driver rndis_host
Jan  1 01:00:39 Gargoyle kern.info kernel: [   37.450000] USB Serial support registered for GSM modem (1-port)
Jan  1 01:00:39 Gargoyle kern.info kernel: [   37.450000] usbcore: registered new interface driver option
Jan  1 01:00:39 Gargoyle kern.info kernel: [   37.460000] option: v0.7.2:USB Driver for GSM modems
Jan  1 01:00:39 Gargoyle kern.info kernel: [   37.480000] USB Serial support registered for Qualcomm USB modem
Jan  1 01:00:39 Gargoyle kern.info kernel: [   37.490000] usbcore: registered new interface driver qcserial
Jan  1 01:00:39 Gargoyle kern.info kernel: [   37.610000] fuse init (API version 7.18)
Jan  1 01:00:42 Gargoyle kern.info kernel: [   42.740000] eth0: link up (1000Mbps/Full duplex)
Jan  1 01:00:43 Gargoyle kern.info kernel: [   43.570000] eth0: link down
Jan  1 01:00:43 Gargoyle kern.info kernel: [   43.580000] device eth0.1 entered promiscuous mode
Jan  1 01:00:43 Gargoyle kern.info kernel: [   43.590000] device eth0 entered promiscuous mode
Jan  1 01:00:43 Gargoyle daemon.notice netifd: Interface 'lan' is now up
Jan  1 01:00:43 Gargoyle daemon.notice netifd: Interface 'loopback' is now up
Jan  1 01:00:43 Gargoyle kern.info kernel: [   43.760000] eth0: link up (1000Mbps/Full duplex)
Jan  1 01:00:43 Gargoyle kern.info kernel: [   43.760000] br-lan: port 1(eth0.1) entered forwarding state
Jan  1 01:00:43 Gargoyle kern.info kernel: [   43.770000] br-lan: port 1(eth0.1) entered forwarding state
Jan  1 01:00:43 Gargoyle user.notice firewall: Reloading firewall due to ifup of lan (br-lan)
Jan  1 01:00:45 Gargoyle kern.info kernel: [   45.770000] br-lan: port 1(eth0.1) entered forwarding state
Jan  1 01:00:46 Gargoyle user.notice usb-modeswitch: 1-0:1.0: Manufacturer=Linux_3.3.8_ehci_hcd Product=Generic_Platform_EHCI_Controller Serial=ehci-platform
Jan  1 01:00:49 Gargoyle kern.info kernel: [   49.240000] device wlan1 entered promiscuous mode
Jan  1 01:00:49 Gargoyle kern.info kernel: [   49.460000] br-lan: port 2(wlan1) entered forwarding state
Jan  1 01:00:49 Gargoyle kern.info kernel: [   49.460000] br-lan: port 2(wlan1) entered forwarding state
Jan  1 01:00:51 Gargoyle kern.info kernel: [   51.460000] br-lan: port 2(wlan1) entered forwarding state
Oct 28 15:44:10 Gargoyle authpriv.info dropbear[1414]: Running in background
Oct 28 15:44:10 Gargoyle user.notice usb-modeswitch: 1-1:1.0: Manufacturer=? Product=USB2.0_Hub Serial=?
Oct 28 15:44:10 Gargoyle daemon.warn httpd_gargoyle[1475]: started as root without requesting chroot(), warning only
Oct 28 15:44:10 Gargoyle daemon.notice httpd_gargoyle[1475]: httpd_gargoyle/1.0 14mar2008 starting on Gargoyle, port 80
Oct 28 15:44:10 Gargoyle user.notice usb-modeswitch: 1-1.1:1.0: Manufacturer=HUAWEI_Technology Product=HUAWEI_Mobile Serial=?
Oct 28 15:44:10 Gargoyle user.notice usb-modeswitch: 1-1.1:1.0: Selecting /etc/usb_modeswitch.d/12d1:14fe for mode switching
Oct 28 15:44:11 Gargoyle syslog.notice usb_modeswitch: switching device 12d1:14fe on 001/003
Oct 28 15:44:11 Gargoyle kern.info kernel: [   54.460000] usb 1-1.1: USB disconnect, device number 3
Oct 28 15:44:11 Gargoyle kern.info kernel: [   54.800000] usb 1-1.1: new high-speed USB device number 4 using ehci-platform
Oct 28 15:44:11 Gargoyle kern.info kernel: [   54.910000] option 1-1.1:1.1: GSM modem (1-port) converter detected
Oct 28 15:44:11 Gargoyle kern.info kernel: [   54.920000] usb 1-1.1: GSM modem (1-port) converter now attached to ttyUSB0
Oct 28 15:44:11 Gargoyle kern.info kernel: [   54.940000] usb 1-1.1: MAC-Address: 0x0c:0x5b:0x8f:0x27:0x9a:0x64
Oct 28 15:44:11 Gargoyle kern.info kernel: [   54.940000] cdc_ncm 1-1.1:1.2: wwan0: register 'cdc_ncm' at usb-ehci-platform-1.1, Mobile Broadband Network Device, 0c:5b:8f:27:9a:64
Oct 28 15:44:11 Gargoyle kern.info kernel: [   54.960000] scsi2 : usb-storage 1-1.1:1.3
Oct 28 15:44:11 Gargoyle kern.info kernel: [   54.960000] scsi3 : usb-storage 1-1.1:1.4
Oct 28 15:44:12 Gargoyle user.notice dnsmasq: DNS rebinding protection is active, will discard upstream RFC1918 responses!
Oct 28 15:44:12 Gargoyle user.notice dnsmasq: Allowing 127.0.0.0/8 responses
Oct 28 15:44:12 Gargoyle daemon.info hostapd: wlan1: STA 3c:a9:f4:5b:33:14 IEEE 802.11: authenticated
Oct 28 15:44:12 Gargoyle daemon.info hostapd: wlan1: STA 3c:a9:f4:5b:33:14 IEEE 802.11: associated (aid 1)
Oct 28 15:44:12 Gargoyle daemon.info hostapd: wlan1: STA 3c:a9:f4:5b:33:14 WPA: pairwise key handshake completed (RSN)
Oct 28 15:44:12 Gargoyle kern.notice kernel: [   55.960000] scsi 2:0:0:0: CD-ROM            HUAWEI   Mass Storage     2.31 PQ: 0 ANSI: 2
Oct 28 15:44:12 Gargoyle kern.notice kernel: [   55.970000] scsi 3:0:0:0: Direct-Access     HUAWEI   TF CARD Storage  2.31 PQ: 0 ANSI: 2
Oct 28 15:44:12 Gargoyle kern.notice kernel: [   55.980000] sd 3:0:0:0: [sda] Attached SCSI removable disk
Oct 28 15:44:15 Gargoyle daemon.info dnsmasq[1583]: started, version 2.66 cachesize 150
Oct 28 15:44:15 Gargoyle daemon.info dnsmasq[1583]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth
Oct 28 15:44:15 Gargoyle daemon.info dnsmasq-dhcp[1583]: DHCP, IP range 10.20.30.100 -- 10.20.30.249, lease time 12h
Oct 28 15:44:15 Gargoyle daemon.info dnsmasq[1583]: using local addresses only for domain lan
Oct 28 15:44:15 Gargoyle daemon.info dnsmasq[1583]: reading /tmp/resolv.conf.auto
Oct 28 15:44:15 Gargoyle daemon.warn dnsmasq[1583]: ignoring nameserver 10.20.30.1 - local interface
Oct 28 15:44:15 Gargoyle daemon.info dnsmasq[1583]: using local addresses only for domain lan
Oct 28 15:44:15 Gargoyle daemon.info dnsmasq[1583]: read /etc/hosts - 2 addresses
Oct 28 15:44:15 Gargoyle daemon.info dnsmasq-dhcp[1583]: read /etc/ethers - 0 addresses
Oct 28 15:44:15 Gargoyle daemon.info dnsmasq-dhcp[1583]: DHCPREQUEST(br-lan) 10.20.30.100 3c:a9:f4:5b:33:14
Oct 28 15:44:15 Gargoyle daemon.info dnsmasq-dhcp[1583]: DHCPACK(br-lan) 10.20.30.100 3c:a9:f4:5b:33:14 qwe
Oct 28 15:44:15 Gargoyle user.err syslog: error starting threads: errno 89 (Function not implemented)
Oct 28 15:44:15 Gargoyle user.info sysinit: exportfs: could not open /var/lib/nfs/.etab.lock for locking: errno 2 (No such file or directory)
Oct 28 15:44:15 Gargoyle user.info sysinit: exportfs: can't lock /var/lib/nfs/etab for writing
Oct 28 15:44:15 Gargoyle user.info sysinit: exportfs: could not open /var/lib/nfs/.xtab.lock for locking: errno 2 (No such file or directory)
Oct 28 15:44:15 Gargoyle user.info sysinit: exportfs: can't lock /var/lib/nfs/xtab for writing
Oct 28 15:44:16 Gargoyle user.info sysinit: ERROR: No valid dynamic DNS service configurations defined
Oct 28 15:44:16 Gargoyle user.info sysinit: (Did you specify correct configuration file path?)
Success

5 Odpowiedź przez daro33

  • daro33
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2013-03-14
  • Posty: 180

Odp: NDIS/QMI w Gargoyle (GUI)

Strasznie długo trwa łączenie po restarcie

6 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 109,272

Odp: NDIS/QMI w Gargoyle (GUI)

Włącz sobie monitor połączenia w gui i jako akcję wybierz restart połączenia wan.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

7 Odpowiedź przez daro33

  • daro33
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2013-03-14
  • Posty: 180

Odp: NDIS/QMI w Gargoyle (GUI)

Mam tak ustawione

8 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 109,272

Odp: NDIS/QMI w Gargoyle (GUI)

A co masz w logach po ifup wan?

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

9 Odpowiedź przez daro33

  • daro33
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2013-03-14
  • Posty: 180

Odp: NDIS/QMI w Gargoyle (GUI)

Jan  1 01:00:39 Gargoyle kern.info kernel: [    0.380000] UDP hash table entries: 256 (order: 0, 4096 bytes)
Jan  1 01:00:39 Gargoyle kern.info kernel: [    0.390000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
Jan  1 01:00:39 Gargoyle kern.info kernel: [    0.390000] NET: Registered protocol family 1
Jan  1 01:00:39 Gargoyle kern.debug kernel: [    0.400000] PCI: CLS 0 bytes, default 32
Jan  1 01:00:39 Gargoyle kern.info kernel: [    0.410000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
Jan  1 01:00:39 Gargoyle kern.info kernel: [    0.420000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
Jan  1 01:00:39 Gargoyle kern.info kernel: [    0.430000] msgmni has been set to 246
Jan  1 01:00:39 Gargoyle kern.info kernel: [    0.430000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
Jan  1 01:00:39 Gargoyle kern.info kernel: [    0.440000] io scheduler noop registered
Jan  1 01:00:39 Gargoyle kern.info kernel: [    0.440000] io scheduler deadline registered (default)
Jan  1 01:00:39 Gargoyle kern.info kernel: [    0.450000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
Jan  1 01:00:39 Gargoyle kern.info kernel: [    0.480000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
Jan  1 01:00:39 Gargoyle kern.info kernel: [    0.490000] console [ttyS0] enabled, bootconsole disabled
Jan  1 01:00:39 Gargoyle kern.warn kernel: [    0.500000] m25p80 spi0.0: found en25q64, expected m25p80
Jan  1 01:00:39 Gargoyle kern.info kernel: [    0.500000] m25p80 spi0.0: en25q64 (8192 Kbytes)
Jan  1 01:00:39 Gargoyle kern.notice kernel: [    0.510000] 5 tp-link partitions found on MTD device spi0.0
Jan  1 01:00:39 Gargoyle kern.notice kernel: [    0.520000] Creating 5 MTD partitions on "spi0.0":
Jan  1 01:00:39 Gargoyle kern.notice kernel: [    0.520000] 0x000000000000-0x000000020000 : "u-boot"
Jan  1 01:00:39 Gargoyle kern.notice kernel: [    0.530000] 0x000000020000-0x00000010eda0 : "kernel"
Jan  1 01:00:39 Gargoyle kern.warn kernel: [    0.530000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
Jan  1 01:00:39 Gargoyle kern.notice kernel: [    0.550000] 0x00000010eda0-0x0000007f0000 : "rootfs"
Jan  1 01:00:39 Gargoyle kern.warn kernel: [    0.550000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
Jan  1 01:00:39 Gargoyle kern.notice kernel: [    0.570000] mtd: partition "rootfs" set to be root filesystem
Jan  1 01:00:39 Gargoyle kern.info kernel: [    0.570000] mtd: partition "rootfs_data" created automatically, ofs=650000, len=1A0000
Jan  1 01:00:39 Gargoyle kern.notice kernel: [    0.580000] 0x000000650000-0x0000007f0000 : "rootfs_data"
Jan  1 01:00:39 Gargoyle kern.notice kernel: [    0.590000] 0x0000007f0000-0x000000800000 : "art"
Jan  1 01:00:39 Gargoyle kern.notice kernel: [    0.590000] 0x000000020000-0x0000007f0000 : "firmware"
Jan  1 01:00:39 Gargoyle kern.info kernel: [    0.730000] ag71xx_mdio: probed
Jan  1 01:00:39 Gargoyle kern.info kernel: [    0.730000] eth0: Atheros AG71xx at 0xb9000000, irq 4
Jan  1 01:00:39 Gargoyle kern.info kernel: [    1.310000] eth0: Atheros AR8327 switch driver attached.
Jan  1 01:00:39 Gargoyle kern.info kernel: [    2.470000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd033, driver=Atheros AR8216/AR8236/AR8316]
Jan  1 01:00:39 Gargoyle kern.info kernel: [   32.740000] PPP generic driver version 2.4.2
Jan  1 01:00:39 Gargoyle kern.info kernel: [   32.850000] tun: Universal TUN/TAP device driver, 1.6
Jan  1 01:00:39 Gargoyle kern.info kernel: [   32.860000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
Jan  1 01:00:39 Gargoyle kern.info kernel: [   32.950000] GRE over IPv4 demultiplexor driver
Jan  1 01:00:39 Gargoyle kern.warn kernel: [   32.970000] ip_gre: Unknown symbol icmpv6_send (err 0)
Jan  1 01:00:39 Gargoyle kern.info kernel: [   33.250000] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
Jan  1 01:00:39 Gargoyle kern.info kernel: [   33.350000] ip_tables: (C) 2000-2006 Netfilter Core Team
Jan  1 01:00:39 Gargoyle kern.info kernel: [   33.690000] NET: Registered protocol family 24
Jan  1 01:00:39 Gargoyle kern.info kernel: [   33.820000] nf_conntrack version 0.5.0 (1978 buckets, 7912 max)
Jan  1 01:00:39 Gargoyle kern.info kernel: [   34.250000] PPTP driver version 0.8.5
Jan  1 01:00:39 Gargoyle kern.info kernel: [   34.870000] xt_time: kernel timezone is -0000
Jan  1 01:00:39 Gargoyle kern.info kernel: [   35.560000]     Hooked IMQ after mangle on PREROUTING
Jan  1 01:00:39 Gargoyle kern.info kernel: [   35.570000]     Hooked IMQ after nat on POSTROUTING
Jan  1 01:00:39 Gargoyle kern.info kernel: [   35.570000] IMQ driver loaded successfully. (numdevs = 2, numqueues = 1)
Jan  1 01:00:39 Gargoyle kern.info kernel: [   35.730000] Netfilter messages via NETLINK v0.30.
Jan  1 01:00:39 Gargoyle kern.notice kernel: [   35.930000] ip_set: protocol 6
Jan  1 01:00:39 Gargoyle kern.info kernel: [   36.500000] usbcore: registered new interface driver cdc_acm
Jan  1 01:00:39 Gargoyle kern.info kernel: [   36.510000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
Jan  1 01:00:39 Gargoyle kern.info kernel: [   36.630000] usbcore: registered new interface driver usblp
Jan  1 01:00:39 Gargoyle kern.info kernel: [   36.660000] usbcore: registered new interface driver usbserial
Jan  1 01:00:39 Gargoyle kern.info kernel: [   36.660000] USB Serial support registered for generic
Jan  1 01:00:39 Gargoyle kern.info kernel: [   36.670000] usbcore: registered new interface driver usbserial_generic
Jan  1 01:00:39 Gargoyle kern.info kernel: [   36.670000] usbserial: USB Serial Driver core
Jan  1 01:00:39 Gargoyle kern.info kernel: [   36.760000] USB Serial support registered for Sierra USB modem
Jan  1 01:00:39 Gargoyle kern.info kernel: [   36.760000] usbcore: registered new interface driver sierra
Jan  1 01:00:39 Gargoyle kern.info kernel: [   36.770000] sierra: v.1.7.40:USB Driver for Sierra Wireless USB modems
Jan  1 01:00:39 Gargoyle kern.info kernel: [   36.790000] usbcore: registered new interface driver sierra_net
Jan  1 01:00:39 Gargoyle kern.info kernel: [   36.910000] usbcore: registered new interface driver ums-alauda
Jan  1 01:00:39 Gargoyle kern.info kernel: [   36.940000] usbcore: registered new interface driver ums-cypress
Jan  1 01:00:39 Gargoyle kern.info kernel: [   36.960000] usbcore: registered new interface driver ums-datafab
Jan  1 01:00:39 Gargoyle kern.info kernel: [   37.020000] usbcore: registered new interface driver ums-freecom
Jan  1 01:00:39 Gargoyle kern.info kernel: [   37.040000] usbcore: registered new interface driver ums-isd200
Jan  1 01:00:39 Gargoyle kern.info kernel: [   37.060000] usbcore: registered new interface driver ums-jumpshot
Jan  1 01:00:39 Gargoyle kern.info kernel: [   37.080000] usbcore: registered new interface driver ums-karma
Jan  1 01:00:39 Gargoyle kern.info kernel: [   37.110000] usbcore: registered new interface driver ums-sddr09
Jan  1 01:00:42 Gargoyle kern.info kernel: [   42.860000] eth0: link up (1000Mbps/Full duplex)
Jan  1 01:00:43 Gargoyle kern.info kernel: [   43.610000] eth0: link down
Jan  1 01:00:43 Gargoyle kern.info kernel: [   43.620000] device eth0.1 entered promiscuous mode
Jan  1 01:00:43 Gargoyle kern.info kernel: [   43.620000] device eth0 entered promiscuous mode
Jan  1 01:00:43 Gargoyle daemon.notice netifd: Interface 'lan' is now up
Jan  1 01:00:43 Gargoyle daemon.notice netifd: Interface 'loopback' is now up
Jan  1 01:00:43 Gargoyle kern.info kernel: [   43.860000] eth0: link up (1000Mbps/Full duplex)
Jan  1 01:00:43 Gargoyle kern.info kernel: [   43.880000] br-lan: port 1(eth0.1) entered forwarding state
Jan  1 01:00:43 Gargoyle kern.info kernel: [   43.880000] br-lan: port 1(eth0.1) entered forwarding state
Jan  1 01:00:43 Gargoyle user.notice firewall: Reloading firewall due to ifup of lan (br-lan)
Jan  1 01:00:45 Gargoyle kern.info kernel: [   45.880000] br-lan: port 1(eth0.1) entered forwarding state
Jan  1 01:00:46 Gargoyle user.notice usb-modeswitch: 1-0:1.0: Manufacturer=Linux_3.3.8_ehci_hcd Product=Generic_Platform_EHCI_Controller Serial=ehci-platform
Jan  1 01:00:49 Gargoyle kern.info kernel: [   49.350000] device wlan1 entered promiscuous mode
Jan  1 01:00:49 Gargoyle kern.info kernel: [   49.560000] br-lan: port 2(wlan1) entered forwarding state
Jan  1 01:00:49 Gargoyle kern.info kernel: [   49.570000] br-lan: port 2(wlan1) entered forwarding state
Jan  1 01:00:51 Gargoyle kern.info kernel: [   51.570000] br-lan: port 2(wlan1) entered forwarding state
Oct 28 19:29:05 Gargoyle authpriv.info dropbear[1414]: Running in background
Oct 28 19:29:05 Gargoyle user.notice usb-modeswitch: 1-1:1.0: Manufacturer=? Product=USB2.0_Hub Serial=?
Oct 28 19:29:05 Gargoyle daemon.warn httpd_gargoyle[1486]: started as root without requesting chroot(), warning only
Oct 28 19:29:05 Gargoyle daemon.notice httpd_gargoyle[1486]: httpd_gargoyle/1.0 14mar2008 starting on Gargoyle, port 80
Oct 28 19:29:05 Gargoyle user.notice usb-modeswitch: 1-1.1:1.0: Manufacturer=HUAWEI_Technology Product=HUAWEI_Mobile Serial=?
Oct 28 19:29:05 Gargoyle user.notice usb-modeswitch: 1-1.1:1.0: Selecting /etc/usb_modeswitch.d/12d1:14fe for mode switching
Oct 28 19:29:06 Gargoyle syslog.notice usb_modeswitch: switching device 12d1:14fe on 001/003
Oct 28 19:29:06 Gargoyle kern.info kernel: [   54.500000] usb 1-1.1: USB disconnect, device number 3
Oct 28 19:29:06 Gargoyle kern.info kernel: [   54.780000] usb 1-1.1: new high-speed USB device number 4 using ehci-platform
Oct 28 19:29:06 Gargoyle kern.info kernel: [   54.890000] option 1-1.1:1.1: GSM modem (1-port) converter detected
Oct 28 19:29:06 Gargoyle kern.info kernel: [   54.900000] usb 1-1.1: GSM modem (1-port) converter now attached to ttyUSB0
Oct 28 19:29:06 Gargoyle kern.info kernel: [   54.920000] usb 1-1.1: MAC-Address: 0x0c:0x5b:0x8f:0x27:0x9a:0x64
Oct 28 19:29:06 Gargoyle kern.info kernel: [   54.920000] cdc_ncm 1-1.1:1.2: wwan0: register 'cdc_ncm' at usb-ehci-platform-1.1, Mobile Broadband Network Device, 0c:5b:8f:27:9a:64
Oct 28 19:29:06 Gargoyle kern.info kernel: [   54.940000] scsi2 : usb-storage 1-1.1:1.3
Oct 28 19:29:06 Gargoyle kern.info kernel: [   54.940000] scsi3 : usb-storage 1-1.1:1.4
Oct 28 19:29:07 Gargoyle user.notice dnsmasq: DNS rebinding protection is active, will discard upstream RFC1918 responses!
Oct 28 19:29:07 Gargoyle user.notice dnsmasq: Allowing 127.0.0.0/8 responses
Oct 28 19:29:07 Gargoyle kern.notice kernel: [   55.940000] scsi 2:0:0:0: CD-ROM            HUAWEI   Mass Storage     2.31 PQ: 0 ANSI: 2
Oct 28 19:29:07 Gargoyle kern.notice kernel: [   55.950000] scsi 3:0:0:0: Direct-Access     HUAWEI   TF CARD Storage  2.31 PQ: 0 ANSI: 2
Oct 28 19:29:07 Gargoyle kern.notice kernel: [   55.960000] sd 3:0:0:0: [sda] Attached SCSI removable disk
Oct 28 19:29:10 Gargoyle daemon.info dnsmasq[1559]: started, version 2.66 cachesize 150
Oct 28 19:29:10 Gargoyle daemon.info dnsmasq[1559]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth
Oct 28 19:29:10 Gargoyle daemon.info dnsmasq-dhcp[1559]: DHCP, IP range 10.20.30.100 -- 10.20.30.249, lease time 12h
Oct 28 19:29:10 Gargoyle daemon.info dnsmasq[1559]: using local addresses only for domain lan
Oct 28 19:29:10 Gargoyle daemon.info dnsmasq[1559]: reading /tmp/resolv.conf.auto
Oct 28 19:29:10 Gargoyle daemon.warn dnsmasq[1559]: ignoring nameserver 10.20.30.1 - local interface
Oct 28 19:29:10 Gargoyle daemon.info dnsmasq[1559]: using local addresses only for domain lan
Oct 28 19:29:10 Gargoyle daemon.info dnsmasq[1559]: read /etc/hosts - 2 addresses
Oct 28 19:29:10 Gargoyle daemon.info dnsmasq-dhcp[1559]: read /etc/ethers - 0 addresses
Oct 28 19:29:10 Gargoyle user.err syslog: error starting threads: errno 89 (Function not implemented)
Oct 28 19:29:10 Gargoyle user.info sysinit: exportfs: could not open /var/lib/nfs/.etab.lock for locking: errno 2 (No such file or directory)
Oct 28 19:29:10 Gargoyle user.info sysinit: exportfs: can't lock /var/lib/nfs/etab for writing
Oct 28 19:29:10 Gargoyle user.info sysinit: exportfs: could not open /var/lib/nfs/.xtab.lock for locking: errno 2 (No such file or directory)
Oct 28 19:29:10 Gargoyle user.info sysinit: exportfs: can't lock /var/lib/nfs/xtab for writing
Oct 28 19:29:11 Gargoyle user.info sysinit: ERROR: No valid dynamic DNS service configurations defined
Oct 28 19:29:11 Gargoyle user.info sysinit: (Did you specify correct configuration file path?)
Oct 28 19:29:24 Gargoyle daemon.info hostapd: wlan1: STA 3c:a9:f4:5b:33:14 IEEE 802.11: authenticated
Oct 28 19:29:24 Gargoyle daemon.info hostapd: wlan1: STA 3c:a9:f4:5b:33:14 IEEE 802.11: associated (aid 1)
Oct 28 19:29:24 Gargoyle daemon.info hostapd: wlan1: STA 3c:a9:f4:5b:33:14 WPA: pairwise key handshake completed (RSN)
Oct 28 19:29:24 Gargoyle daemon.info dnsmasq-dhcp[1559]: DHCPREQUEST(br-lan) 10.20.30.100 3c:a9:f4:5b:33:14
Oct 28 19:29:24 Gargoyle daemon.info dnsmasq-dhcp[1559]: DHCPACK(br-lan) 10.20.30.100 3c:a9:f4:5b:33:14 qwe
Oct 28 19:29:36 Gargoyle user.notice usb-modeswitch: 1-1.1:1.1: Manufacturer=HUAWEI_Technology Product=HUAWEI_Mobile Serial=?
Oct 28 19:29:36 Gargoyle user.notice root: vsftpd init: mounted = 0
Oct 28 19:29:36 Gargoyle user.info sysinit: ERROR: No drives attached, no directories to share!
Oct 28 19:29:37 Gargoyle user.info sysinit: setting up led USB1
Oct 28 19:29:37 Gargoyle user.info sysinit: setting up led USB2
Oct 28 19:29:37 Gargoyle user.info sysinit: setting up led WLAN2G
Oct 28 19:29:53 Gargoyle user.notice usb-modeswitch: 1-1.1:1.0: Manufacturer=HUAWEI_Technology Product=HUAWEI_Mobile Serial=?
Oct 28 19:29:53 Gargoyle user.notice usb-modeswitch: 1-1.1:1.1: Manufacturer=HUAWEI_Technology Product=HUAWEI_Mobile Serial=?
Oct 28 19:29:55 Gargoyle user.notice usb-modeswitch: 1-1.1:1.2: Manufacturer=HUAWEI_Technology Product=HUAWEI_Mobile Serial=?
Oct 28 19:29:56 Gargoyle user.notice usb-modeswitch: 1-1.1:1.3: Manufacturer=HUAWEI_Technology Product=HUAWEI_Mobile Serial=?
Oct 28 19:29:56 Gargoyle user.notice usb-modeswitch: 1-1.1:1.4: Manufacturer=HUAWEI_Technology Product=HUAWEI_Mobile Serial=?
Oct 28 19:33:01 Gargoyle user.notice /usr/lib/gargoyle/ping_watchdog.sh: WAN Restart
Oct 28 19:33:02 Gargoyle daemon.notice netifd: wan (3391): Trying to set mode
Oct 28 19:33:05 Gargoyle daemon.notice netifd: Interface 'wan' is now down
Oct 28 19:33:07 Gargoyle daemon.notice netifd: wan (3454): Trying to set mode
Oct 28 19:33:10 Gargoyle daemon.notice netifd: wan (3454): Trying to set mode
Oct 28 19:33:14 Gargoyle kern.info kernel: [  302.360000] cdc_ncm: wwan0: 43 mbit/s downlink 43 mbit/s uplink
Oct 28 19:33:14 Gargoyle kern.info kernel: [  302.370000] cdc_ncm: wwan0: network connection: connected
Oct 28 19:33:14 Gargoyle daemon.notice netifd: wan (3578): udhcpc (v1.19.4) started
Oct 28 19:33:14 Gargoyle daemon.notice netifd: wan (3578): Sending discover...
Oct 28 19:33:14 Gargoyle daemon.notice netifd: wan (3578): Sending select for 164.126.43.182...
Oct 28 19:33:14 Gargoyle daemon.notice netifd: wan (3578): Lease of 164.126.43.182 obtained, lease time 518400
Oct 28 19:33:14 Gargoyle daemon.notice netifd: Interface 'wan' is now up
Oct 28 19:33:15 Gargoyle user.notice firewall: Reloading firewall due to ifup of wan (wwan0)
Oct 28 19:33:16 Gargoyle daemon.info dnsmasq[1559]: reading /tmp/resolv.conf.auto
Oct 28 19:33:16 Gargoyle daemon.info dnsmasq[1559]: using nameserver 89.108.195.20#53
Oct 28 19:33:16 Gargoyle daemon.info dnsmasq[1559]: using nameserver 89.108.202.20#53
Oct 28 19:33:16 Gargoyle daemon.warn dnsmasq[1559]: ignoring nameserver 10.20.30.1 - local interface
Oct 28 19:33:16 Gargoyle daemon.info dnsmasq[1559]: using local addresses only for domain lan
Oct 28 19:35:07 Gargoyle kern.warn kernel: [  354.320000] ipt_bandwidth: timezone shift of 60 minutes detected, adjusting
Oct 28 19:35:07 Gargoyle kern.warn kernel: [  354.330000]                old minutes west=0, new minutes west=-60
Success

10 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 109,272

Odp: NDIS/QMI w Gargoyle (GUI)

Monitor połączenie zadziałał.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

11 Odpowiedź przez daro33

  • daro33
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2013-03-14
  • Posty: 180

Odp: NDIS/QMI w Gargoyle (GUI)

Tak zadziałał, tylko dlaczego połączenie nie jest dokonane zaraz po starcie?

12 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 109,272

Odp: NDIS/QMI w Gargoyle (GUI)

Z racji tego że jak router/sieć startuje to interfejs modemu nie jest jeszcze dostępny.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

13 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 109,272

Odp: NDIS/QMI w Gargoyle (GUI)

Chyba rozwiązałem problem z inicjacją połączenia po restarcie. Muszę jeszcze parę testów zrobić.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

14 Odpowiedź przez Przmus

  • Przmus
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2013-06-05
  • Posty: 332

Odp: NDIS/QMI w Gargoyle (GUI)

Super! Na pewno bardzo ułatwi to nawiązywanie połączenia w NDIS.
Mam takie pytanie (z racji tego, że nie mogę przetestować na swoim routerze), czy ifup wan również rozłączy połączenie z internetem (komenda "AT^NDISDUP=1,0")? Chodzi o to, by uniknąć zawieszenia modemu i ewentualnie móc zrestartować połączenie komendą ifup wan.

15 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 109,272

Odp: NDIS/QMI w Gargoyle (GUI)

Tak, przed nawiązaniem połączenia jest zrobione rozłączenie.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

16 Odpowiedź przez krism

  • krism
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2013-10-28
  • Posty: 15

Odp: NDIS/QMI w Gargoyle (GUI)

Witam serdecznie i zwracam się o pomoc.
Próbuję uruchomić HUAWEI E3276s-151 (od Orange) na routerze TP-Link TL-WDR4300 v1.
Zainstalowałem najnowsze Gargoyle z NDIS  ( poniżej konfiguracja).
Niestety modem nie nawiązuje połączenia .

Nazwa urządzenia:Gargoyle
Wersja Gargoyle:1.5.11.1 (r38462), by obsy
Model:TP-Link TL-WDR4300 v1
Konfiguracja urządzenia:Brama sieciowa

Konfiguracja
Połączenie:Modem 3G/LTE (NDIS)
interfejs:wwan0
protokół: NDIS
urządzenie: /dev/ttyUSB0
Operator: Polska- Orange

W załączeniu log ( próba ifup wan również kończy się niepowodzeniem).

Jan  1 01:00:38 Gargoyle syslog.info syslogd started: BusyBox v1.19.4
Jan  1 01:00:38 Gargoyle kern.notice kernel: klogd started: BusyBox v1.19.4 (2013-10-21 17:06:26 CEST)
Jan  1 01:00:38 Gargoyle kern.notice kernel: [    0.000000] Linux version 3.3.8 (cezary@eko.one.pl) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #138 Sun Oct 27 17:31:04 CET 2013
Jan  1 01:00:38 Gargoyle kern.debug kernel: [    0.000000] MyLoader: sysp=b3a3d853, boardp=492118fc, parts=f35d1cdf
Jan  1 01:00:38 Gargoyle kern.info kernel: [    0.000000] bootconsole [early0] enabled
Jan  1 01:00:38 Gargoyle kern.info kernel: [    0.000000] CPU revision is: 0001974c (MIPS 74Kc)
Jan  1 01:00:38 Gargoyle kern.info kernel: [    0.000000] SoC: Atheros AR9344 rev 2
Jan  1 01:00:38 Gargoyle kern.info kernel: [    0.000000] Clocks: CPU:560.000MHz, DDR:450.000MHz, AHB:225.000MHz, Ref:40.000MHz
Jan  1 01:00:38 Gargoyle kern.info kernel: [    0.000000] Determined physical RAM map:
Jan  1 01:00:38 Gargoyle kern.info kernel: [    0.000000]  memory: 08000000 @ 00000000 (usable)
Jan  1 01:00:38 Gargoyle kern.info kernel: [    0.000000] Initrd not found or empty - disabling initrd
Jan  1 01:00:38 Gargoyle kern.warn kernel: [    0.000000] Zone PFN ranges:
Jan  1 01:00:38 Gargoyle kern.warn kernel: [    0.000000]   Normal   0x00000000 -> 0x00008000
Jan  1 01:00:38 Gargoyle kern.warn kernel: [    0.000000] Movable zone start PFN for each node
Jan  1 01:00:38 Gargoyle kern.warn kernel: [    0.000000] Early memory PFN ranges
Jan  1 01:00:38 Gargoyle kern.warn kernel: [    0.000000]     0: 0x00000000 -> 0x00008000
Jan  1 01:00:38 Gargoyle kern.debug kernel: [    0.000000] On node 0 totalpages: 32768
Jan  1 01:00:38 Gargoyle kern.debug kernel: [    0.000000] free_area_init_node: node 0, pgdat 802fdda0, node_mem_map 81000000
Jan  1 01:00:38 Gargoyle kern.debug kernel: [    0.000000]   Normal zone: 256 pages used for memmap
Jan  1 01:00:38 Gargoyle kern.debug kernel: [    0.000000]   Normal zone: 0 pages reserved
Jan  1 01:00:38 Gargoyle kern.debug kernel: [    0.000000]   Normal zone: 32512 pages, LIFO batch:7
Jan  1 01:00:38 Gargoyle kern.debug kernel: [    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
Jan  1 01:00:38 Gargoyle kern.debug kernel: [    0.000000] pcpu-alloc: [0] 0
Jan  1 01:00:38 Gargoyle kern.warn kernel: [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
Jan  1 01:00:38 Gargoyle kern.notice kernel: [    0.000000] Kernel command line:  board=TL-WDR4300 console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
Jan  1 01:00:38 Gargoyle kern.info kernel: [    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
Jan  1 01:00:38 Gargoyle kern.info kernel: [    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Jan  1 01:00:38 Gargoyle kern.info kernel: [    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Jan  1 01:00:38 Gargoyle kern.warn kernel: [    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Jan  1 01:00:38 Gargoyle kern.warn kernel: [    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Jan  1 01:00:38 Gargoyle kern.info kernel: [    0.000000] Writing ErrCtl register=00000000
Jan  1 01:00:38 Gargoyle kern.info kernel: [    0.000000] Readback ErrCtl register=00000000
Jan  1 01:00:38 Gargoyle kern.info kernel: [    0.000000] Memory: 126404k/131072k available (2255k kernel code, 4668k reserved, 425k data, 216k init, 0k highmem)
Jan  1 01:00:38 Gargoyle kern.info kernel: [    0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Jan  1 01:00:38 Gargoyle kern.info kernel: [    0.000000] NR_IRQS:51
Jan  1 01:00:38 Gargoyle kern.info kernel: [    0.000000] Calibrating delay loop... 278.93 BogoMIPS (lpj=1394688)
Jan  1 01:00:38 Gargoyle kern.info kernel: [    0.070000] pid_max: default: 32768 minimum: 301
Jan  1 01:00:38 Gargoyle kern.info kernel: [    0.070000] Mount-cache hash table entries: 512
Jan  1 01:00:38 Gargoyle kern.info kernel: [    0.080000] NET: Registered protocol family 16
Jan  1 01:00:38 Gargoyle kern.info kernel: [    0.080000] gpiochip_add: registered GPIOs 0 to 22 on device: ath79
Jan  1 01:00:38 Gargoyle kern.info kernel: [    0.090000] MIPS: machine is TP-LINK TL-WDR3600/4300/4310
Jan  1 01:00:38 Gargoyle kern.warn kernel: [    0.090000] registering PCI controller with io_map_base unset
Jan  1 01:00:38 Gargoyle kern.info kernel: [    0.310000] bio: create slab <bio-0> at 0
Jan  1 01:00:39 Gargoyle kern.info kernel: [    0.310000] PCI host bridge to bus 0000:00
Jan  1 01:00:39 Gargoyle kern.info kernel: [    0.320000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff]
Jan  1 01:00:39 Gargoyle kern.info kernel: [    0.320000] pci_bus 0000:00: root bus resource [io  0x0000]
Jan  1 01:00:39 Gargoyle kern.debug kernel: [    0.330000] pci 0000:00:00.0: [168c:0033] type 0 class 0x000280
Jan  1 01:00:39 Gargoyle kern.err kernel: [    0.330000] pci 0000:00:00.0: invalid calibration data
Jan  1 01:00:39 Gargoyle kern.debug kernel: [    0.330000] pci 0000:00:00.0: reg 10: [mem 0x00000000-0x0001ffff 64bit]
Jan  1 01:00:39 Gargoyle kern.debug kernel: [    0.330000] pci 0000:00:00.0: reg 30: [mem 0x00000000-0x0000ffff pref]
Jan  1 01:00:39 Gargoyle kern.debug kernel: [    0.330000] pci 0000:00:00.0: supports D1
Jan  1 01:00:39 Gargoyle kern.debug kernel: [    0.330000] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
Jan  1 01:00:39 Gargoyle kern.info kernel: [    0.330000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1001ffff 64bit]
Jan  1 01:00:39 Gargoyle kern.info kernel: [    0.340000] pci 0000:00:00.0: BAR 6: assigned [mem 0x10020000-0x1002ffff pref]
Jan  1 01:00:39 Gargoyle kern.info kernel: [   10.140000] scsi1 : usb-storage 1-1.2:1.1
Jan  1 01:00:39 Gargoyle kern.notice kernel: [   11.140000] scsi 0:0:0:0: CD-ROM            HUAWEI   Mass Storage     2.31 PQ: 0 ANSI: 2
Jan  1 01:00:39 Gargoyle kern.notice kernel: [   11.150000] scsi 1:0:0:0: Direct-Access     HUAWEI   TF CARD Storage  2.31 PQ: 0 ANSI: 2
Jan  1 01:00:39 Gargoyle kern.notice kernel: [   11.160000] sd 1:0:0:0: [sda] Attached SCSI removable disk
Jan  1 01:00:39 Gargoyle kern.info kernel: [   30.110000] eth0: link down
Jan  1 01:00:39 Gargoyle kern.info kernel: [   30.620000] Loading modules backported from Linux version master-2013-06-27-0-gdcfa6d5
Jan  1 01:00:39 Gargoyle kern.info kernel: [   30.630000] Backport generated by backports.git backports-20130617-4-ge3220f5
Jan  1 01:00:39 Gargoyle kern.info kernel: [   30.780000] cfg80211: Calling CRDA to update world regulatory domain
Jan  1 01:00:39 Gargoyle kern.info kernel: [   30.780000] cfg80211: World regulatory domain updated:
Jan  1 01:00:39 Gargoyle kern.info kernel: [   30.790000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
Jan  1 01:00:39 Gargoyle kern.info kernel: [   30.800000] cfg80211:   (2400000 KHz - 2483000 KHz @ 40000 KHz), (N/A, 3000 mBm)
Jan  1 01:00:39 Gargoyle kern.info kernel: [   30.800000] cfg80211:   (5140000 KHz - 5860000 KHz @ 40000 KHz), (N/A, 3000 mBm)
Jan  1 01:00:39 Gargoyle kern.debug kernel: [   31.890000] ath: EEPROM regdomain: 0x0
Jan  1 01:00:39 Gargoyle kern.debug kernel: [   31.890000] ath: EEPROM indicates default country code should be used
Jan  1 01:00:39 Gargoyle kern.debug kernel: [   31.890000] ath: doing EEPROM country->regdmn map search
Jan  1 01:00:39 Gargoyle kern.debug kernel: [   31.890000] ath: country maps to regdmn code: 0x3a
Jan  1 01:00:39 Gargoyle kern.debug kernel: [   31.890000] ath: Country alpha2 being used: US
Jan  1 01:00:39 Gargoyle kern.debug kernel: [   31.890000] ath: Regpair used: 0x3a
Jan  1 01:00:39 Gargoyle kern.debug kernel: [   31.900000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
Jan  1 01:00:39 Gargoyle kern.debug kernel: [   31.900000] Registered led device: ath9k-phy0
Jan  1 01:00:39 Gargoyle kern.info kernel: [   31.900000] ieee80211 phy0: Atheros AR9340 Rev:0 mem=0xb8100000, irq=47
Jan  1 01:00:39 Gargoyle kern.warn kernel: [   31.910000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
Jan  1 01:00:39 Gargoyle kern.debug kernel: [   31.920000] ath: EEPROM regdomain: 0x0
Jan  1 01:00:39 Gargoyle kern.debug kernel: [   31.920000] ath: EEPROM indicates default country code should be used
Jan  1 01:00:39 Gargoyle kern.debug kernel: [   31.920000] ath: doing EEPROM country->regdmn map search
Jan  1 01:00:39 Gargoyle kern.debug kernel: [   31.920000] ath: country maps to regdmn code: 0x3a
Jan  1 01:00:39 Gargoyle kern.debug kernel: [   31.920000] ath: Country alpha2 being used: US
Jan  1 01:00:39 Gargoyle kern.debug kernel: [   31.920000] ath: Regpair used: 0x3a
Jan  1 01:00:39 Gargoyle kern.debug kernel: [   31.920000] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
Jan  1 01:00:39 Gargoyle kern.debug kernel: [   31.920000] Registered led device: ath9k-phy1
Jan  1 01:00:39 Gargoyle kern.info kernel: [   31.920000] ieee80211 phy1: Atheros AR9300 Rev:4 mem=0xb0000000, irq=40
Jan  1 01:00:39 Gargoyle kern.info kernel: [   31.940000] cfg80211: Calling CRDA for country: US
Jan  1 01:00:39 Gargoyle kern.info kernel: [   31.940000] cfg80211: Regulatory domain changed to country: US
Jan  1 01:00:39 Gargoyle kern.info kernel: [   31.950000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
Jan  1 01:00:39 Gargoyle kern.info kernel: [   31.950000] cfg80211:   (2400000 KHz - 2483000 KHz @ 40000 KHz), (N/A, 3000 mBm)
Jan  1 01:00:39 Gargoyle kern.info kernel: [   31.960000] cfg80211:   (5140000 KHz - 5860000 KHz @ 40000 KHz), (N/A, 3000 mBm)
Jan  1 01:00:43 Gargoyle kern.info kernel: [   43.420000] eth0: link up (1000Mbps/Full duplex)
Jan  1 01:00:43 Gargoyle kern.info kernel: [   43.520000] eth0: link down
Jan  1 01:00:43 Gargoyle kern.info kernel: [   43.530000] device eth0.1 entered promiscuous mode
Jan  1 01:00:43 Gargoyle kern.info kernel: [   43.530000] device eth0 entered promiscuous mode
Jan  1 01:00:43 Gargoyle daemon.notice netifd: Interface 'lan' is now up
Jan  1 01:00:43 Gargoyle daemon.notice netifd: Interface 'loopback' is now up
Jan  1 01:00:43 Gargoyle user.notice firewall: Reloading firewall due to ifup of lan (br-lan)
Jan  1 01:00:45 Gargoyle kern.info kernel: [   45.540000] eth0: link up (1000Mbps/Full duplex)
Jan  1 01:00:45 Gargoyle kern.info kernel: [   45.550000] br-lan: port 1(eth0.1) entered forwarding state
Jan  1 01:00:45 Gargoyle kern.info kernel: [   45.550000] br-lan: port 1(eth0.1) entered forwarding state
Jan  1 01:00:46 Gargoyle user.notice usb-modeswitch: 1-0:1.0: Manufacturer=Linux_3.3.8_ehci_hcd Product=Generic_Platform_EHCI_Controller Serial=ehci-platform
Jan  1 01:00:47 Gargoyle kern.info kernel: [   47.550000] br-lan: port 1(eth0.1) entered forwarding state
Jan  1 01:22:39 Gargoyle authpriv.info dropbear[1265]: Running in background
Jan  1 01:22:40 Gargoyle daemon.warn httpd_gargoyle[1307]: started as root without requesting chroot(), warning only
Jan  1 01:22:40 Gargoyle daemon.notice httpd_gargoyle[1307]: httpd_gargoyle/1.0 14mar2008 starting on Gargoyle, port 80
Jan  1 01:22:40 Gargoyle user.notice usb-modeswitch: 1-1:1.0: Manufacturer=? Product=USB2.0_Hub Serial=?
Jan  1 01:22:41 Gargoyle user.notice usb-modeswitch: 1-1.2:1.0: Manufacturer=HUAWEI_Technology Product=HUAWEI_Mobile Serial=?
Jan  1 01:22:41 Gargoyle user.notice usb-modeswitch: 1-1.2:1.0: Selecting /etc/usb_modeswitch.d/12d1:156a for mode switching
Jan  1 01:22:42 Gargoyle syslog.notice usb_modeswitch: switching device 12d1:156a on 001/003
Jan  1 01:22:42 Gargoyle kern.info kernel: [   51.920000] usb 1-1.2: USB disconnect, device number 3
Jan  1 01:22:42 Gargoyle user.notice dnsmasq: DNS rebinding protection is active, will discard upstream RFC1918 responses!
Jan  1 01:22:42 Gargoyle user.notice dnsmasq: Allowing 127.0.0.0/8 responses
Jan  1 01:22:42 Gargoyle kern.info kernel: [   52.210000] usb 1-1.2: new high-speed USB device number 4 using ehci-platform
Jan  1 01:22:42 Gargoyle kern.info kernel: [   52.320000] usb 1-1.2: MAC-Address: 0x0c:0x5b:0x8f:0x27:0x9a:0x64
Jan  1 01:22:42 Gargoyle kern.info kernel: [   52.330000] cdc_ncm 1-1.2:1.2: wwan0: register 'cdc_ncm' at usb-ehci-platform-1.2, Mobile Broadband Network Device, 0c:5b:8f:27:9a:64
Jan  1 01:22:42 Gargoyle kern.info kernel: [   52.350000] scsi2 : usb-storage 1-1.2:1.3
Jan  1 01:22:43 Gargoyle kern.notice kernel: [   53.350000] scsi 2:0:0:0: Direct-Access     HUAWEI   TF CARD Storage  2.31 PQ: 0 ANSI: 2
Jan  1 01:22:43 Gargoyle kern.notice kernel: [   53.360000] sd 2:0:0:0: [sda] Attached SCSI removable disk
Jan  1 01:22:45 Gargoyle daemon.info dnsmasq[1521]: started, version 2.66 cachesize 150
Jan  1 01:22:45 Gargoyle daemon.info dnsmasq[1521]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth
Jan  1 01:22:45 Gargoyle daemon.info dnsmasq-dhcp[1521]: DHCP, IP range 192.168.1.100 -- 192.168.1.249, lease time 12h
Jan  1 01:22:45 Gargoyle daemon.info dnsmasq[1521]: using local addresses only for domain lan
Jan  1 01:22:45 Gargoyle daemon.info dnsmasq[1521]: reading /tmp/resolv.conf.auto
Jan  1 01:22:45 Gargoyle daemon.warn dnsmasq[1521]: ignoring nameserver 192.168.1.1 - local interface
Jan  1 01:22:45 Gargoyle daemon.info dnsmasq[1521]: using local addresses only for domain lan
Jan  1 01:22:45 Gargoyle daemon.info dnsmasq[1521]: read /etc/hosts - 2 addresses
Jan  1 01:22:45 Gargoyle daemon.info dnsmasq-dhcp[1521]: read /etc/ethers - 0 addresses
Jan  1 01:22:46 Gargoyle user.err syslog: error starting threads: errno 89 (Function not implemented)
Jan  1 01:22:46 Gargoyle user.info sysinit: exportfs: could not open /var/lib/nfs/.etab.lock for locking: errno 2 (No such file or directory)
Jan  1 01:22:46 Gargoyle user.info sysinit: exportfs: can't lock /var/lib/nfs/etab for writing
Jan  1 01:22:46 Gargoyle user.info sysinit: exportfs: could not open /var/lib/nfs/.xtab.lock for locking: errno 2 (No such file or directory)
Jan  1 01:22:46 Gargoyle user.info sysinit: exportfs: can't lock /var/lib/nfs/xtab for writing
Jan  1 01:22:47 Gargoyle user.info sysinit: ERROR: No valid dynamic DNS service configurations defined
Jan  1 01:22:47 Gargoyle user.info sysinit: (Did you specify correct configuration file path?)
Jan  1 01:22:56 Gargoyle daemon.info dnsmasq-dhcp[1521]: DHCPINFORM(br-lan) 192.168.1.153 00:1f:16:95:6b:51
Jan  1 01:22:56 Gargoyle daemon.info dnsmasq-dhcp[1521]: DHCPACK(br-lan) 192.168.1.153 00:1f:16:95:6b:51 AE5630EZ
Jan  1 01:23:12 Gargoyle user.notice usb-modeswitch: 1-1.2:1.1: Manufacturer=HUAWEI_Technology Product=HUAWEI_Mobile Serial=?
Jan  1 01:23:12 Gargoyle user.notice root: vsftpd init: mounted = 0
Jan  1 01:23:12 Gargoyle user.info sysinit: ERROR: No drives attached, no directories to share!
Jan  1 01:23:12 Gargoyle user.info sysinit: setting up led USB1
Jan  1 01:23:12 Gargoyle user.info sysinit: setting up led USB2
Jan  1 01:23:12 Gargoyle user.info sysinit: setting up led WLAN2G
Jan  1 01:23:26 Gargoyle user.notice usb-modeswitch: 1-1.2:1.0: Manufacturer=HUAWEI_Technology Product=HUAWEI_Mobile Serial=?
Jan  1 01:23:27 Gargoyle user.notice usb-modeswitch: 1-1.2:1.1: Manufacturer=HUAWEI_Technology Product=HUAWEI_Mobile Serial=?
Jan  1 01:23:27 Gargoyle user.notice usb-modeswitch: 1-1.2:1.2: Manufacturer=HUAWEI_Technology Product=HUAWEI_Mobile Serial=?
Jan  1 01:23:27 Gargoyle user.notice usb-modeswitch: 1-1.2:1.3: Manufacturer=HUAWEI_Technology Product=HUAWEI_Mobile Serial=?
Success

Jan  1 01:26:15 Gargoyle daemon.notice netifd: wan (3046): Can't open device /dev/ttyUSB0.
Jan  1 01:26:18 Gargoyle daemon.notice netifd: Interface 'wan' is now down
Success

17 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 109,272

Odp: NDIS/QMI w Gargoyle (GUI)

Masz ten nowy modem którego jeszcze nie dodałem. Pokaż wynik polecenia:

cat /proc/bus/usb/devices

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

18 Odpowiedź przez krism

  • krism
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2013-10-28
  • Posty: 15

Odp: NDIS/QMI w Gargoyle (GUI)

cat /proc/bus/usb/devices

T:  Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=480  MxCh= 1
B:  Alloc=  0/800 us ( 0%), #Int=  1, #Iso=  0
D:  Ver= 2.00 Cls=09(hub  ) Sub=00 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=1d6b ProdID=0002 Rev= 3.03
S:  Manufacturer=Linux 3.3.8 ehci_hcd
S:  Product=Generic Platform EHCI Controller
S:  SerialNumber=ehci-platform
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   4 Ivl=256ms

T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=480  MxCh= 4
D:  Ver= 2.00 Cls=09(hub  ) Sub=00 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=05e3 ProdID=0608 Rev=77.64
S:  Product=USB2.0 Hub
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   1 Ivl=256ms

T:  Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#=  6 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=12d1 ProdID=156c Rev= 1.02
S:  Manufacturer=HUAWEI Technology
S:  Product=HUAWEI Mobile
C:* #Ifs= 4 Cfg#= 1 Atr=80 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=02 Prot=10 Driver=(none)
E:  Ad=81(I) Atr=03(Int.) MxPS=  64 Ivl=2ms
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=02 Prot=12 Driver=(none)
E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:  If#= 2 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=02 Prot=16 Driver=cdc_ncm
E:  Ad=84(I) Atr=03(Int.) MxPS=  64 Ivl=2ms
I:* If#= 2 Alt= 1 #EPs= 3 Cls=ff(vend.) Sub=02 Prot=16 Driver=cdc_ncm
E:  Ad=84(I) Atr=03(Int.) MxPS=  64 Ivl=2ms
E:  Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms

19 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 109,272

Odp: NDIS/QMI w Gargoyle (GUI)

echo "12d1 156c" > /sys/bus/usb-serial/drivers/option1/new_id
ifup wan

Zrób z konsoli.

Później
echo "12d1 156c" > /sys/bus/usb-serial/drivers/option1/new_id
wpisz jako pierwszą linię w pliku /etc/rc.local.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

20 Odpowiedź przez ryba825

  • Zarejestrowany: 2012-09-30
  • Posty: 52

Odp: NDIS/QMI w Gargoyle (GUI)

Będzie to w obrazach dla MR3020? smile

21 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 109,272

Odp: NDIS/QMI w Gargoyle (GUI)

Docelowo tak.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

22 Odpowiedź przez krism

  • krism
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2013-10-28
  • Posty: 15

Odp: NDIS/QMI w Gargoyle (GUI)

po pierwszych komendach dostałem
Jan  1 02:16:18 Gargoyle kern.info kernel: [ 3268.170000] option 1-1.1:1.0: GSM modem (1-port) converter detected
Jan  1 02:16:18 Gargoyle kern.info kernel: [ 3268.180000] usb 1-1.1: GSM modem (1-port) converter now attached to ttyUSB0
Jan  1 02:16:18 Gargoyle kern.info kernel: [ 3268.190000] option 1-1.1:1.1: GSM modem (1-port) converter detected
Jan  1 02:16:18 Gargoyle kern.info kernel: [ 3268.190000] usb 1-1.1: GSM modem (1-port) converter now attached to ttyUSB1
Jan  1 02:16:42 Gargoyle daemon.notice netifd: wan (10222): Error setting PIN, check card manually
Success

23 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 109,272

Odp: NDIS/QMI w Gargoyle (GUI)

Raz - interfejsy masz i pewnie w zwykłym ras możesz nawet go uruchomić.
Dwa - pinu nie podałeś? Lub zły dałeś.

Pokaż jak teraz cat /proc/bus/usb/devices wygląda.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

24 Odpowiedź przez krism

  • krism
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2013-10-28
  • Posty: 15

Odp: NDIS/QMI w Gargoyle (GUI)

T:  Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=480  MxCh= 1
B:  Alloc=  1/800 us ( 0%), #Int=  3, #Iso=  0
D:  Ver= 2.00 Cls=09(hub  ) Sub=00 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=1d6b ProdID=0002 Rev= 3.03
S:  Manufacturer=Linux 3.3.8 ehci_hcd
S:  Product=Generic Platform EHCI Controller
S:  SerialNumber=ehci-platform
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   4 Ivl=256ms

T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=480  MxCh= 4
D:  Ver= 2.00 Cls=09(hub  ) Sub=00 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=05e3 ProdID=0608 Rev=77.64
S:  Product=USB2.0 Hub
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   1 Ivl=256ms

T:  Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#=  6 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=12d1 ProdID=156c Rev= 1.02
S:  Manufacturer=HUAWEI Technology
S:  Product=HUAWEI Mobile
C:* #Ifs= 4 Cfg#= 1 Atr=80 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=02 Prot=10 Driver=option
E:  Ad=81(I) Atr=03(Int.) MxPS=  64 Ivl=2ms
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=02 Prot=12 Driver=option
E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:  If#= 2 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=02 Prot=16 Driver=cdc_ncm
E:  Ad=84(I) Atr=03(Int.) MxPS=  64 Ivl=2ms
I:* If#= 2 Alt= 1 #EPs= 3 Cls=ff(vend.) Sub=02 Prot=16 Driver=cdc_ncm
E:  Ad=84(I) Atr=03(Int.) MxPS=  64 Ivl=2ms
E:  Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms

25 Odpowiedź przez krism

  • krism
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2013-10-28
  • Posty: 15

Odp: NDIS/QMI w Gargoyle (GUI)

Pin wpisałem w gui ( prawidłowy)