FAQ o OpenWrt | Sprzedam różne routery | Oddam

ambrozy5 · 2025-07-16 13:54:55

ambrozy5
Użytkownik
Nieaktywny

Zarejestrowany: 2015-01-27
Posty: 2,429

Odp: Ciekawy test przepustowości iperf3 routera samego ze sobą :)

zgadza się , na dodatek cały pasywny a obudowa to masywny aluminiowy kloc. oba lany intela. nat @1Gb to okolo 8-12% zużycia tego dwurdzeniowego i czterowątkowego procka.

100Mb/s - 25Gb/s
Podróżne : GL.Inet MT3000 +1TB hdd
Działka : rb260gs 1j wdm 1Gb+ ruckus r310 + nb m5 + kilka kamer ip + panel 285Wp + lifepo4 12v 60Ah .

Dyziek · 2025-07-26 10:18:27

Dyziek
Użytkownik
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2019-05-05
Posty: 273

Odp: Ciekawy test przepustowości iperf3 routera samego ze sobą :)

M710q i5-7500T, Opnsense 25.1.10, maksymalnie zdławiony CPU (ciągnie 10.8-11.6W).
Zapięty OpenVPN (site-to-site), 3xWG, VLANy, Suricata, Zenarmor, CrowdSec, Adblocker, kilkanaście urządzeń aktywnych w tle itp.
FreeBSD 14.2

connecting to host 127.0.0.1, port 5201
[ 5] local 127.0.0.1 port 13685 connected to 127.0.0.1 port 5201
[ ID] Interval Transfer Bitrate Retr Cwnd
[ 5] 0.00-1.00 sec 4.68 GBytes 40.2 Gbits/sec 0 2.01 MBytes
[ 5] 1.00-2.00 sec 4.72 GBytes 40.5 Gbits/sec 0 2.01 MBytes
[ 5] 2.00-3.00 sec 4.69 GBytes 40.3 Gbits/sec 0 2.01 MBytes
[ 5] 3.00-4.00 sec 4.70 GBytes 40.2 Gbits/sec 0 2.01 MBytes
[ 5] 4.00-5.00 sec 4.69 GBytes 40.4 Gbits/sec 0 2.01 MBytes
[ 5] 5.00-6.00 sec 4.71 GBytes 40.4 Gbits/sec 0 2.01 MBytes
[ 5] 6.00-7.00 sec 4.73 GBytes 40.6 Gbits/sec 0 2.01 MBytes
[ 5] 7.00-8.00 sec 4.74 GBytes 40.7 Gbits/sec 0 2.01 MBytes
[ 5] 8.00-9.00 sec 4.70 GBytes 40.4 Gbits/sec 0 2.01 MBytes
[ 5] 9.00-10.00 sec 4.69 GBytes 40.3 Gbits/sec 0 2.01 MBytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-10.00 sec 47.0 GBytes 40.4 Gbits/sec 0 sender
[ 5] 0.00-10.00 sec 47.0 GBytes 40.4 Gbits/sec receiver

VM na Proxmox, zainstalowany Opnsense 25.7, i5-9500T. Też zdławiony
To samo co wyżej, ale bez VPNów, kilku userów
FreeBSD 14.3

Connecting to host 127.0.0.1, port 5201
[ 5] local 127.0.0.1 port 1753 connected to 127.0.0.1 port 5201
[ ID] Interval Transfer Bitrate Retr Cwnd
[ 5] 0.00-1.01 sec 7.20 GBytes 61.3 Gbits/sec 0 2.00 MBytes
[ 5] 1.01-2.00 sec 7.11 GBytes 61.4 Gbits/sec 0 2.00 MBytes
[ 5] 2.00-3.01 sec 7.21 GBytes 61.4 Gbits/sec 0 2.00 MBytes
[ 5] 3.01-4.01 sec 7.35 GBytes 63.4 Gbits/sec 0 2.00 MBytes
[ 5] 4.01-5.00 sec 7.33 GBytes 63.4 Gbits/sec 0 2.00 MBytes
[ 5] 5.00-6.01 sec 7.39 GBytes 62.8 Gbits/sec 0 2.00 MBytes
[ 5] 6.01-7.01 sec 7.29 GBytes 62.6 Gbits/sec 0 2.00 MBytes
[ 5] 7.01-8.01 sec 7.25 GBytes 62.3 Gbits/sec 0 2.00 MBytes
[ 5] 8.01-9.01 sec 7.22 GBytes 62.3 Gbits/sec 0 2.00 MBytes
[ 5] 9.01-10.00 sec 7.30 GBytes 63.1 Gbits/sec 0 2.00 MBytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-10.00 sec 72.7 GBytes 62.4 Gbits/sec 0 sender
[ 5] 0.00-10.00 sec 72.7 GBytes 62.4 Gbits/sec receiver

iperf Done.

tomaszu · 2025-09-28 21:32:42

tomaszu
Użytkownik
Nieaktywny

Zarejestrowany: 2019-11-16
Posty: 181

Odp: Ciekawy test przepustowości iperf3 routera samego ze sobą :)

TP-Link TL-WR850N v2

root@OpenWrt:~# uname -a
Linux OpenWrt 6.6.104 #0 Fri Sep 19 21:19:38 2025 mips GNU/Linux
root@OpenWrt:~# ubus call system board
{
        "kernel": "6.6.104",
        "hostname": "OpenWrt",
        "system": "MediaTek MT7628AN ver:1 eco:2",
        "model": "TP-Link TL-WR850N v2",
        "board_name": "tplink,tl-wr850n-v2",
        "rootfs_type": "squashfs",
        "release": {
                "distribution": "OpenWrt",
                "version": "24.10.3",
                "revision": "r28872-daca7c049b",
                "target": "ramips/mt76x8",
                "description": "OpenWrt 24.10.3 r28872-daca7c049b",
                "builddate": "1758316778"
        }
}
root@OpenWrt:~# iperf3 -s -D && iperf3 -c 127.0.0.1
Connecting to host 127.0.0.1, port 5201
[  5] local 127.0.0.1 port 40274 connected to 127.0.0.1 port 5201
[ ID] Interval           Transfer     Bitrate         Retr  Cwnd
[  5]   0.00-1.01   sec  47.0 MBytes   390 Mbits/sec    0   1023 KBytes
[  5]   1.01-2.00   sec  45.8 MBytes   387 Mbits/sec    0   1023 KBytes
[  5]   2.00-3.00   sec  46.6 MBytes   391 Mbits/sec    0   1023 KBytes
[  5]   3.00-4.00   sec  46.9 MBytes   393 Mbits/sec    0   1023 KBytes
[  5]   4.00-5.00   sec  46.4 MBytes   389 Mbits/sec    0   1023 KBytes
[  5]   5.00-6.00   sec  46.8 MBytes   392 Mbits/sec    0   1023 KBytes
[  5]   6.00-7.00   sec  46.5 MBytes   390 Mbits/sec    0   1023 KBytes
[  5]   7.00-8.00   sec  46.9 MBytes   394 Mbits/sec    0   1023 KBytes
[  5]   8.00-9.00   sec  46.6 MBytes   391 Mbits/sec    0   1023 KBytes
[  5]   9.00-10.00  sec  46.6 MBytes   390 Mbits/sec    0   1023 KBytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bitrate         Retr
[  5]   0.00-10.00  sec   466 MBytes   391 Mbits/sec    0             sender
[  5]   0.00-10.00  sec   466 MBytes   391 Mbits/sec                  receiver

iperf Done.

bulgar71 · 2025-11-27 21:44:48

bulgar71
Użytkownik
Nieaktywny

Skąd: WRO
Zarejestrowany: 2017-11-14
Posty: 879

Odp: Ciekawy test przepustowości iperf3 routera samego ze sobą :)

root@GL-BE9300:~# iperf3 -s -D && iperf3 -c 127.0.0.1
Connecting to host 127.0.0.1, port 5201
[ 5] local 127.0.0.1 port 53426 connected to 127.0.0.1 port 5201
[ ID] Interval Transfer Bitrate Retr Cwnd
[ 5] 0.00-1.00 sec 669 MBytes 5.61 Gbits/sec 0 5.00 MBytes
[ 5] 1.00-2.00 sec 619 MBytes 5.19 Gbits/sec 0 5.00 MBytes
[ 5] 2.00-3.00 sec 618 MBytes 5.18 Gbits/sec 0 5.00 MBytes
[ 5] 3.00-4.00 sec 609 MBytes 5.11 Gbits/sec 0 5.00 MBytes
[ 5] 4.00-5.00 sec 582 MBytes 4.88 Gbits/sec 0 5.00 MBytes
[ 5] 5.00-6.00 sec 601 MBytes 5.04 Gbits/sec 0 5.00 MBytes
[ 5] 6.00-7.00 sec 628 MBytes 5.27 Gbits/sec 0 5.00 MBytes
[ 5] 7.00-8.00 sec 616 MBytes 5.17 Gbits/sec 0 5.00 MBytes
[ 5] 8.00-9.00 sec 619 MBytes 5.19 Gbits/sec 0 5.00 MBytes
[ 5] 9.00-10.00 sec 600 MBytes 5.03 Gbits/sec 0 5.00 MBytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-10.00 sec 6.02 GBytes 5.17 Gbits/sec 0 sender
[ 5] 0.00-10.00 sec 6.01 GBytes 5.16 Gbits/sec receiver

FLINT 3

ASUS TUF AX 6000 <-> QNAP TS-473A <->Pihole<->

Dyziek · 2025-11-29 12:36:07

Dyziek
Użytkownik
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2019-05-05
Posty: 273

Odp: Ciekawy test przepustowości iperf3 routera samego ze sobą :)

Raspberry Pi 4, v1.4, 600-1800 MHz, 8GB

root@OpenWrt:~# iperf3 -s -D && iperf3 -c 127.0.0.1
Connecting to host 127.0.0.1, port 5201
[ 5] local 127.0.0.1 port 46418 connected to 127.0.0.1 port 5201
[ ID] Interval Transfer Bitrate Retr Cwnd
[ 5] 0.00-1.00 sec 1.59 GBytes 13.6 Gbits/sec 0 1023 KBytes
[ 5] 1.00-2.00 sec 1.02 GBytes 8.78 Gbits/sec 0 1023 KBytes
[ 5] 2.00-3.00 sec 1.02 GBytes 8.76 Gbits/sec 0 1023 KBytes
[ 5] 3.00-4.00 sec 1.02 GBytes 8.76 Gbits/sec 0 1023 KBytes
[ 5] 4.00-5.00 sec 1.02 GBytes 8.75 Gbits/sec 0 1023 KBytes
[ 5] 5.00-6.00 sec 1.02 GBytes 8.76 Gbits/sec 0 1023 KBytes
[ 5] 6.00-7.00 sec 1.02 GBytes 8.77 Gbits/sec 0 1023 KBytes
[ 5] 7.00-8.00 sec 1.02 GBytes 8.76 Gbits/sec 0 1023 KBytes
[ 5] 8.00-9.00 sec 1.02 GBytes 8.74 Gbits/sec 0 1023 KBytes
[ 5] 9.00-10.00 sec 1.02 GBytes 8.75 Gbits/sec 0 1023 KBytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-10.00 sec 10.8 GBytes 9.25 Gbits/sec 0 sender
[ 5] 0.00-10.00 sec 10.8 GBytes 9.25 Gbits/sec receiver

iperf Done.

andrut · 2025-11-30 06:57:00

andrut
Użytkownik
Nieaktywny

Zarejestrowany: 2013-05-11
Posty: 292

Odp: Ciekawy test przepustowości iperf3 routera samego ze sobą :)

NanoPi R5C, 24.10.4

Connecting to host 127.0.0.1, port 5201
[  5] local 127.0.0.1 port 56374 connected to 127.0.0.1 port 5201
[ ID] Interval           Transfer     Bitrate         Retr  Cwnd
[  5]   0.00-1.00   sec   471 MBytes  3.94 Gbits/sec    2   1.81 MBytes
[  5]   1.00-2.00   sec   507 MBytes  4.26 Gbits/sec    0   1.94 MBytes
[  5]   2.00-3.00   sec   686 MBytes  5.76 Gbits/sec    0   1.94 MBytes
[  5]   3.00-4.00   sec   674 MBytes  5.65 Gbits/sec    0   1.94 MBytes
[  5]   4.00-5.00   sec   640 MBytes  5.37 Gbits/sec    0   1.94 MBytes
[  5]   5.00-6.00   sec   622 MBytes  5.22 Gbits/sec    0   2.94 MBytes
[  5]   6.00-7.00   sec   660 MBytes  5.54 Gbits/sec    0   2.94 MBytes
[  5]   7.00-8.00   sec   677 MBytes  5.68 Gbits/sec    0   2.94 MBytes
[  5]   8.00-9.00   sec   699 MBytes  5.87 Gbits/sec    0   4.43 MBytes
[  5]   9.00-10.00  sec   684 MBytes  5.74 Gbits/sec    0   4.43 MBytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bitrate         Retr
[  5]   0.00-10.00  sec  6.18 GBytes  5.31 Gbits/sec    2             sender
[  5]   0.00-10.00  sec  6.18 GBytes  5.31 Gbits/sec                  receiver

iperf Done.

prognoza pogody dla Warszawy

steel_rat · 2025-11-30 11:23:11

steel_rat
Użytkownik
Nieaktywny

Zarejestrowany: 2017-04-30
Posty: 567

Odp: Ciekawy test przepustowości iperf3 routera samego ze sobą :)

Tak dla porównania:
Asus TUF-AX6000

Connecting to host 127.0.0.1, port 5201
[  5] local 127.0.0.1 port 43858 connected to 127.0.0.1 port 5201
[ ID] Interval           Transfer     Bitrate         Retr  Cwnd
[  5]   0.00-1.00   sec   801 MBytes  6.71 Gbits/sec    0   2.62 MBytes
[  5]   1.00-2.00   sec   787 MBytes  6.60 Gbits/sec    0   2.62 MBytes
[  5]   2.00-3.00   sec   787 MBytes  6.60 Gbits/sec    0   2.62 MBytes
[  5]   3.00-4.00   sec   788 MBytes  6.61 Gbits/sec    0   2.62 MBytes
[  5]   4.00-5.00   sec   788 MBytes  6.61 Gbits/sec    0   2.62 MBytes
[  5]   5.00-6.00   sec   790 MBytes  6.63 Gbits/sec    0   2.62 MBytes
[  5]   6.00-7.00   sec   780 MBytes  6.54 Gbits/sec    0   2.62 MBytes
[  5]   7.00-8.00   sec   769 MBytes  6.45 Gbits/sec    0   2.62 MBytes
[  5]   8.00-9.00   sec   790 MBytes  6.63 Gbits/sec    0   2.62 MBytes
[  5]   9.00-10.00  sec   786 MBytes  6.59 Gbits/sec    0   2.62 MBytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bitrate         Retr
[  5]   0.00-10.00  sec  7.68 GBytes  6.60 Gbits/sec    0             sender
[  5]   0.00-10.00  sec  7.68 GBytes  6.60 Gbits/sec                  receiver

Cudy WR3000H

[  5] local 127.0.0.1 port 33476 connected to 127.0.0.1 port 5201
[ ID] Interval           Transfer     Bitrate         Retr  Cwnd
[  5]   0.00-1.00   sec   532 MBytes  4.45 Gbits/sec    0   1.25 MBytes
[  5]   1.00-2.00   sec   537 MBytes  4.52 Gbits/sec    0   1.44 MBytes
[  5]   2.00-3.00   sec   544 MBytes  4.56 Gbits/sec    0   1.44 MBytes
[  5]   3.00-4.00   sec   541 MBytes  4.54 Gbits/sec    0   1.62 MBytes
[  5]   4.00-5.00   sec   558 MBytes  4.69 Gbits/sec    0   1.87 MBytes
[  5]   5.00-6.00   sec   555 MBytes  4.66 Gbits/sec    0   1.87 MBytes
[  5]   6.00-7.00   sec   533 MBytes  4.47 Gbits/sec    0   1.87 MBytes
[  5]   7.00-8.00   sec   538 MBytes  4.51 Gbits/sec    0   1.87 MBytes
[  5]   8.00-9.00   sec   549 MBytes  4.61 Gbits/sec    0   1.87 MBytes
[  5]   9.00-10.00  sec   548 MBytes  4.59 Gbits/sec    0   1.87 MBytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bitrate         Retr
[  5]   0.00-10.00  sec  5.31 GBytes  4.56 Gbits/sec    0             sender
[  5]   0.00-10.00  sec  5.31 GBytes  4.56 Gbits/sec                  receiver

Xiaomi AX3200

[  5] local 127.0.0.1 port 53786 connected to 127.0.0.1 port 5201
[ ID] Interval           Transfer     Bitrate         Retr  Cwnd
[  5]   0.00-1.00   sec   704 MBytes  5.89 Gbits/sec    0   1.87 MBytes
[  5]   1.00-2.00   sec   695 MBytes  5.84 Gbits/sec    0   1.87 MBytes
[  5]   2.00-3.00   sec   696 MBytes  5.84 Gbits/sec    0   1.87 MBytes
[  5]   3.00-4.00   sec   688 MBytes  5.77 Gbits/sec    0   1.87 MBytes
[  5]   4.00-5.00   sec   692 MBytes  5.80 Gbits/sec    0   1.87 MBytes
[  5]   5.00-6.00   sec   713 MBytes  5.99 Gbits/sec    0   1.87 MBytes
[  5]   6.00-7.00   sec   698 MBytes  5.85 Gbits/sec    0   1.87 MBytes
[  5]   7.00-8.00   sec   763 MBytes  6.40 Gbits/sec    0   1.87 MBytes
[  5]   8.00-9.00   sec   640 MBytes  5.37 Gbits/sec    0   1.87 MBytes
[  5]   9.00-10.00  sec   679 MBytes  5.70 Gbits/sec    0   1.87 MBytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bitrate         Retr
[  5]   0.00-10.00  sec  6.82 GBytes  5.86 Gbits/sec    0             sender
[  5]   0.00-10.00  sec  6.82 GBytes  5.86 Gbits/sec                  receiver

Linksys EA7500v2

[  5] local 127.0.0.1 port 46034 connected to 127.0.0.1 port 5201
[ ID] Interval           Transfer     Bitrate         Retr  Cwnd
[  5]   0.00-1.00   sec  76.8 MBytes   643 Mbits/sec    0   1.94 MBytes
[  5]   1.00-2.00   sec  76.8 MBytes   644 Mbits/sec    0   1.94 MBytes
[  5]   2.00-3.00   sec  73.9 MBytes   619 Mbits/sec    0   1.94 MBytes
[  5]   3.00-4.00   sec  72.1 MBytes   606 Mbits/sec    0   1.94 MBytes
[  5]   4.00-5.00   sec  74.0 MBytes   621 Mbits/sec    0   1.94 MBytes
[  5]   5.00-6.00   sec  72.8 MBytes   611 Mbits/sec    0   1.94 MBytes
[  5]   6.00-7.00   sec  73.2 MBytes   613 Mbits/sec    0   1.94 MBytes
[  5]   7.00-8.00   sec  73.9 MBytes   621 Mbits/sec    0   1.94 MBytes
[  5]   8.00-9.00   sec  72.6 MBytes   609 Mbits/sec    0   1.94 MBytes
[  5]   9.00-10.01  sec  76.5 MBytes   639 Mbits/sec    0   1.94 MBytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bitrate         Retr
[  5]   0.00-10.01  sec   750 MBytes   629 Mbits/sec    0             sender
[  5]   0.00-10.01  sec   751 MBytes   629 Mbits/sec                  receiver

Dyziek · 2025-11-30 14:26:59

Dyziek
Użytkownik
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2019-05-05
Posty: 273

Odp: Ciekawy test przepustowości iperf3 routera samego ze sobą :)

Cudy przy obecnej cenie rynkowej ma naprawdę bdb wydajnosc. Nie testowalem X6 i WR3000p, sprawdze przy okazji.
Zaluje, ze rpi nie ma natywnie 2 portow lan.
Nieco rozczarowany jestem R5c od NanoPi, spodziwalem sie wyższych wartosci (dane Andrut’a)

krisux · 2025-11-30 18:39:21

krisux
Użytkownik
Nieaktywny

Zarejestrowany: 2018-01-10
Posty: 104

Odp: Ciekawy test przepustowości iperf3 routera samego ze sobą :)

Nanopi r5c

root@OpenWrt:~# iperf3 -s -D && iperf3 -c 127.0.0.1
Connecting to host 127.0.0.1, port 5201
[  5] local 127.0.0.1 port 41750 connected to 127.0.0.1 port 5201
[ ID] Interval           Transfer     Bitrate         Retr  Cwnd
[  5]   0.00-1.00   sec   834 MBytes  6.99 Gbits/sec    0    639 KBytes
[  5]   1.00-2.00   sec   848 MBytes  7.12 Gbits/sec    0    959 KBytes
[  5]   2.00-3.00   sec   848 MBytes  7.12 Gbits/sec    0    959 KBytes
[  5]   3.00-4.00   sec   845 MBytes  7.09 Gbits/sec    0    959 KBytes
[  5]   4.00-5.00   sec   844 MBytes  7.08 Gbits/sec    0    959 KBytes
[  5]   5.00-6.00   sec   844 MBytes  7.08 Gbits/sec    0    959 KBytes
[  5]   6.00-7.00   sec   836 MBytes  7.01 Gbits/sec    0    959 KBytes
[  5]   7.00-8.00   sec   840 MBytes  7.05 Gbits/sec    0    959 KBytes
[  5]   8.00-9.00   sec   841 MBytes  7.05 Gbits/sec    0    959 KBytes
[  5]   9.00-10.00  sec   844 MBytes  7.07 Gbits/sec    0    959 KBytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bitrate         Retr
[  5]   0.00-10.00  sec  8.23 GBytes  7.07 Gbits/sec    0             sender
[  5]   0.00-10.00  sec  8.23 GBytes  7.07 Gbits/sec                  receiver

iperf Done.

root@OpenWrt:~# ubus call system board
{
        "kernel": "6.6.116",
        "hostname": "OpenWrt",
        "system": "ARMv8 Processor rev 0",
        "model": "FriendlyElec NanoPi R5C",
        "board_name": "friendlyarm,nanopi-r5c",
        "rootfs_type": "ext4",
        "release": {
                "distribution": "OpenWrt",
                "version": "24.10-SNAPSHOT",
                "revision": "r29030-ae51d0098e",
                "target": "rockchip/armv8",
                "description": "OpenWrt 24.10-SNAPSHOT r29030-ae51d0098e",
                "builddate": "1762795784"
        }
}

luckyman · 2025-12-02 10:50:02

luckyman
Użytkownik
Nieaktywny

Zarejestrowany: 2021-06-27
Posty: 113

Odp: Ciekawy test przepustowości iperf3 routera samego ze sobą :)

COMFAST CF-WR632AX za 135 zł
root@Routed_Client_NAT:~# ubus call system board
{
"kernel": "6.12.59",
"hostname": "Routed_Client_NAT",
"system": "ARMv8 Processor rev 4",
"model": "COMFAST CF-WR632AX (OpenWrt U-Boot layout)",
"board_name": "comfast,cf-wr632ax-ubootmod",
"rootfs_type": "squashfs",
"release": {
"distribution": "OpenWrt",
"version": "SNAPSHOT",
"firmware_url": "https://downloads.openwrt.org/",
"revision": "r32187-5bdf1b8d9c",
"target": "mediatek/filogic",
"description": "OpenWrt SNAPSHOT r32187-5bdf1b8d9c",
"builddate": "1764597956"
}
}

root@Routed_Client_NAT:~# iperf3 -s -D && iperf3 -c 127.0.0.1
Connecting to host 127.0.0.1, port 5201
[ 5] local 127.0.0.1 port 51328 connected to 127.0.0.1 port 5201
[ ID] Interval Transfer Bitrate Retr Cwnd
[ 5] 0.00-1.00 sec 537 MBytes 4.50 Gbits/sec 0 5.00 MBytes
[ 5] 1.00-2.00 sec 508 MBytes 4.26 Gbits/sec 0 5.00 MBytes
[ 5] 2.00-3.00 sec 525 MBytes 4.40 Gbits/sec 0 5.00 MBytes
[ 5] 3.00-4.00 sec 349 MBytes 2.93 Gbits/sec 0 5.00 MBytes
[ 5] 4.00-5.00 sec 541 MBytes 4.54 Gbits/sec 0 5.00 MBytes
[ 5] 5.00-6.00 sec 552 MBytes 4.63 Gbits/sec 0 5.00 MBytes
[ 5] 6.00-7.00 sec 410 MBytes 3.44 Gbits/sec 0 5.00 MBytes
[ 5] 7.00-8.00 sec 518 MBytes 4.35 Gbits/sec 0 5.00 MBytes
[ 5] 8.00-9.00 sec 383 MBytes 3.21 Gbits/sec 0 5.00 MBytes
[ 5] 9.00-10.00 sec 277 MBytes 2.32 Gbits/sec 0 5.00 MBytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-10.00 sec 5.24 GBytes 4.50 Gbits/sec 0 sender
[ 5] 0.00-10.00 sec 5.24 GBytes 4.50 Gbits/sec receiver

Cezary · 2025-12-06 17:04:40

Cezary
...
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2006-02-25
Posty: 116,153

Odp: Ciekawy test przepustowości iperf3 routera samego ze sobą :)

GMKtec M5 plus

Connecting to host 127.0.0.1, port 5201
[  5] local 127.0.0.1 port 55058 connected to 127.0.0.1 port 5201
[ ID] Interval           Transfer     Bitrate         Retr  Cwnd
[  5]   0.00-1.00   sec  4.76 GBytes  40.8 Gbits/sec    0    639 KBytes       
[  5]   1.00-2.00   sec  4.86 GBytes  41.7 Gbits/sec    0    639 KBytes       
[  5]   2.00-3.16   sec  0.00 Bytes  0.00 bits/sec    0    639 KBytes       
[  5]   3.16-4.00   sec  3.32 GBytes  33.8 Gbits/sec    0    639 KBytes       
[  5]   4.00-5.00   sec  4.31 GBytes  37.0 Gbits/sec    0    639 KBytes       
[  5]   5.00-6.00   sec  4.68 GBytes  40.2 Gbits/sec    0    959 KBytes       
[  5]   6.00-7.00   sec  4.16 GBytes  35.7 Gbits/sec    0    959 KBytes       
[  5]   7.00-8.00   sec  5.28 GBytes  45.3 Gbits/sec    0    959 KBytes       
[  5]   8.00-9.00   sec  5.28 GBytes  45.4 Gbits/sec    0    959 KBytes       
[  5]   9.00-10.00  sec  1.46 GBytes  12.6 Gbits/sec    0    959 KBytes       
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bitrate         Retr
[  5]   0.00-10.00  sec  51.0 GBytes  43.8 Gbits/sec    0            sender
[  5]   0.00-10.00  sec  51.0 GBytes  43.8 Gbits/sec                  receiver

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

tomaszu · 2025-12-27 22:15:05

tomaszu
Użytkownik
Nieaktywny

Zarejestrowany: 2019-11-16
Posty: 181

Odp: Ciekawy test przepustowości iperf3 routera samego ze sobą :)

tomaszu napisał/a:

To u mnie dla kontrastu na starym hardwarze (TP-Link TL-MR3420 v5):

root@OpenWrt:~# iperf3 -s -D && iperf3 -c 127.0.0.1
Connecting to host 127.0.0.1, port 5201
[  5] local 127.0.0.1 port 35898 connected to 127.0.0.1 port 5201
[ ID] Interval           Transfer     Bitrate         Retr  Cwnd
[  5]   0.00-1.00   sec  47.0 MBytes   394 Mbits/sec    0    639 KBytes
[  5]   1.00-2.00   sec  47.5 MBytes   399 Mbits/sec    0    639 KBytes
[  5]   2.00-3.00   sec  49.1 MBytes   412 Mbits/sec    0    639 KBytes
[  5]   3.00-4.00   sec  46.1 MBytes   387 Mbits/sec    0    639 KBytes
[  5]   4.00-5.00   sec  44.5 MBytes   373 Mbits/sec    0    639 KBytes
[  5]   5.00-6.00   sec  46.0 MBytes   386 Mbits/sec    0    639 KBytes
[  5]   6.00-7.00   sec  46.5 MBytes   390 Mbits/sec    0    639 KBytes
[  5]   7.00-8.00   sec  46.5 MBytes   390 Mbits/sec    0    639 KBytes
[  5]   8.00-9.00   sec  47.8 MBytes   400 Mbits/sec    0    639 KBytes
[  5]   9.00-10.00  sec  49.2 MBytes   413 Mbits/sec    0    639 KBytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bitrate         Retr
[  5]   0.00-10.00  sec   470 MBytes   394 Mbits/sec    0             sender
[  5]   0.00-10.01  sec   470 MBytes   394 Mbits/sec                  receiver

iperf Done.
root@OpenWrt:~# ubus call system board
{
        "kernel": "5.15.167",
        "hostname": "OpenWrt",
        "system": "MediaTek MT7628AN ver:1 eco:2",
        "model": "TP-Link TL-MR3420 v5",
        "board_name": "tplink,tl-mr3420-v5",
        "rootfs_type": "squashfs",
        "release": {
                "distribution": "OpenWrt",
                "version": "23.05.5",
                "revision": "r24106-10cc5fcd00",
                "target": "ramips/mt76x8",
                "description": "OpenWrt 23.05.5 r24106-10cc5fcd00"
        }
}

To samo urządzenie na 25.12.0-rc1:

root@OpenWrt:/# iperf3 -s -D && iperf3 -c 127.0.0.1 && ubus call system board
Connecting to host 127.0.0.1, port 5201
[  5] local 127.0.0.1 port 42872 connected to 127.0.0.1 port 5201
[ ID] Interval           Transfer     Bitrate         Retr  Cwnd
[  5]   0.00-1.00   sec  47.2 MBytes   396 Mbits/sec    0   1023 KBytes
[  5]   1.00-2.00   sec  47.4 MBytes   397 Mbits/sec    0   1023 KBytes
[  5]   2.00-3.00   sec  47.2 MBytes   397 Mbits/sec    0   1023 KBytes
[  5]   3.00-4.00   sec  47.6 MBytes   398 Mbits/sec    0   1023 KBytes
[  5]   4.00-5.00   sec  46.8 MBytes   393 Mbits/sec    0   1023 KBytes
[  5]   5.00-6.00   sec  47.2 MBytes   395 Mbits/sec    0   1023 KBytes
[  5]   6.00-7.00   sec  47.0 MBytes   395 Mbits/sec    0   1023 KBytes
[  5]   7.00-8.00   sec  47.2 MBytes   396 Mbits/sec    0   1023 KBytes
[  5]   8.00-9.00   sec  47.1 MBytes   395 Mbits/sec    0   1023 KBytes
[  5]   9.00-10.01  sec  47.2 MBytes   396 Mbits/sec    0   1023 KBytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bitrate         Retr
[  5]   0.00-10.01  sec   472 MBytes   396 Mbits/sec    0            sender
[  5]   0.00-10.01  sec   472 MBytes   396 Mbits/sec                  receiver

iperf Done.
{
        "kernel": "6.12.62",
        "hostname": "OpenWrt",
        "system": "MediaTek MT7628AN ver:1 eco:2",
        "model": "TP-Link TL-MR3420 v5",
        "board_name": "tplink,tl-mr3420-v5",
        "rootfs_type": "squashfs",
        "release": {
                "distribution": "OpenWrt",
                "version": "25.12.0-rc1",
                "firmware_url": "https://downloads.openwrt.org/",
                "revision": "r32353-9e9b05130c",
                "target": "ramips/mt76x8",
                "description": "OpenWrt 25.12.0-rc1 r32353-9e9b05130c",
                "builddate": "1766089549"
        }
}

mar_w · 2025-12-28 18:52:09

mar_w
Użytkownik
Nieaktywny

Zarejestrowany: 2014-08-16
Posty: 2,124

Odp: Ciekawy test przepustowości iperf3 routera samego ze sobą :)

tego typu testy obarczone są błędem "słabego" CPU w porównaniu do jego przepustowości, która czasami może być dużo większa.
jako dodatek powinno się podawać wynik % użycia wszystkich rdzeni/wątków CPU z htop.

Co z tego, że czysta przepustowość będzie na poziomie 1 Gbps skoro słaby procesor musi generować setki tysięcy pakietów i podczas tej operacji brakuje mu mocy przerobowej, stąd wynik tylko 400 Mbps.
Generowanie pakietów iperf3 to nie jest zadanie routera, on ma zupełnie inne funkcje.

to samo w GMKtec M5 plus.
Wynik imponujący ale ten procesor obsługuje 16 linii PCIe 3.0 (czyli jak podaje pan Google przepustowość na poziomie 126 Gbps) a więc istnieją jakieś przeszkody w osiągnięciu tego wyniku.
Czy jest to wysycenie CPU i nie da rady więcej generować pakietów ?
Czy może coś innego ?

Xiaomi AX3000T @ Netgear R6220
* DVBT2 - T230C *

ambrozy5 · 2026-03-21 16:53:53

ambrozy5
Użytkownik
Nieaktywny

Zarejestrowany: 2015-01-27
Posty: 2,429

Odp: Ciekawy test przepustowości iperf3 routera samego ze sobą :)

Wpadło mi w łapy pudełko bqeel y8 max wiec postanowiłem sprawdzić co to za złom, no i wcale nie taki złom, na początek poleciał armbian . Jest na to openwrt, później się temu przyjrzę. procesor tam to amlogic s905x3 , 4GB ram, gbit lan na realteku i porty usb 3.0 + 2.0.

root@armbian:~# iperf3 -s -D && iperf3 -c 127.0.0.1
Connecting to host 127.0.0.1, port 5201
[  5] local 127.0.0.1 port 34132 connected to 127.0.0.1 port 5201
[ ID] Interval           Transfer     Bitrate         Retr  Cwnd
[  5]   0.00-1.00   sec   936 MBytes  7.85 Gbits/sec    0   1023 KBytes
[  5]   1.00-2.00   sec   835 MBytes  7.01 Gbits/sec    0   1023 KBytes
[  5]   2.00-3.00   sec   836 MBytes  7.01 Gbits/sec    0   1023 KBytes
[  5]   3.00-4.00   sec   834 MBytes  7.00 Gbits/sec    0   1023 KBytes
[  5]   4.00-5.00   sec   833 MBytes  6.99 Gbits/sec    0   1023 KBytes
[  5]   5.00-6.00   sec   838 MBytes  7.03 Gbits/sec    0   1023 KBytes
[  5]   6.00-7.00   sec   833 MBytes  6.99 Gbits/sec    0   1023 KBytes
[  5]   7.00-8.00   sec   830 MBytes  6.96 Gbits/sec    0   1023 KBytes
[  5]   8.00-9.00   sec   831 MBytes  6.97 Gbits/sec    0    895 KBytes
[  5]   9.00-10.00  sec   835 MBytes  7.00 Gbits/sec    0   1023 KBytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bitrate         Retr
[  5]   0.00-10.00  sec  8.24 GBytes  7.08 Gbits/sec    0            sender
[  5]   0.00-10.00  sec  8.24 GBytes  7.08 Gbits/sec                  receiver

iperf Done.

100Mb/s - 25Gb/s
Podróżne : GL.Inet MT3000 +1TB hdd
Działka : rb260gs 1j wdm 1Gb+ ruckus r310 + nb m5 + kilka kamer ip + panel 285Wp + lifepo4 12v 60Ah .

WasylNS · 2026-03-22 20:32:19

WasylNS
Użytkownik
Nieaktywny

Zarejestrowany: 2014-01-22
Posty: 38

Odp: Ciekawy test przepustowości iperf3 routera samego ze sobą :)

Tak dla porównania z innymi maszynami:

System:
  Host: openmediavault Kernel: 6.12.74+deb12-amd64 arch: x86_64 bits: 64
  Console: pty pts/0 Distro: openmediavault 8.1.2-1 (Synchrony)
Machine:
  Type: Desktop System: WYSE product: Dell Wyse Thin Client Desktop 5060 v: Rev 1
    serial: 63CA9NQY5J2
  Mobo: Inventec model: 0W63N3 v: A01 serial: xxxxxxxxxxxxx UEFI: Phoenix v: 1.0E
    date: 03/20/2017
CPU:
  Info: quad core AMD GX-424CC SOC with Radeon R5E Graphics [MCP] speed (MHz): avg: 1000
    min/max: 1000/2400
Graphics:
  Device-1: Advanced Micro Devices [AMD/ATI] Mullins [Radeon R4/R5 Graphics] driver: radeon
    v: kernel
  Display: server: No display server data found. Headless machine? tty: 110x25
  API: N/A Message: No API data available in console. Headless machine?
  Info: Tools: No graphics tools found.
Network:
  Device-1: Realtek RTL8111/8168/8211/8411 PCI Express Gigabit Ethernet driver: r8169
Drives:
  Local Storage: total: 931.51 GiB used: 127.88 GiB (13.7%)
Info:
  Memory: total: 16 GiB note: est. available: 14.57 GiB used: 1.55 GiB (10.6%)
  Processes: 178 Uptime: 1d 40m Init: systemd Shell: Bash inxi: 3.3.38

  
  root@openmediavault:~# iperf3 -s -D && iperf3 -c 127.0.0.1
Connecting to host 127.0.0.1, port 5201
[  5] local 127.0.0.1 port 60842 connected to 127.0.0.1 port 5201
[ ID] Interval           Transfer     Bitrate         Retr  Cwnd
[  5]   0.00-1.00   sec  1.19 GBytes  10.2 Gbits/sec    0   2.50 MBytes       
[  5]   1.00-2.00   sec  1.16 GBytes  10.0 Gbits/sec    0   2.50 MBytes       
[  5]   2.00-3.00   sec   982 MBytes  8.24 Gbits/sec    0   2.50 MBytes       
[  5]   3.00-4.00   sec  1009 MBytes  8.47 Gbits/sec    0   2.50 MBytes       
[  5]   4.00-5.00   sec  1.25 GBytes  10.8 Gbits/sec    0   2.50 MBytes       
[  5]   5.00-6.00   sec   342 MBytes  2.87 Gbits/sec    0   2.50 MBytes       
[  5]   6.00-7.00   sec  1.27 GBytes  10.9 Gbits/sec    0   2.50 MBytes       
[  5]   7.00-8.00   sec   542 MBytes  4.55 Gbits/sec    0   2.50 MBytes       
[  5]   8.00-9.00   sec  1.23 GBytes  10.6 Gbits/sec    0   2.50 MBytes       
[  5]   9.00-10.00  sec  1.24 GBytes  10.7 Gbits/sec    0   2.50 MBytes       
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bitrate         Retr
[  5]   0.00-10.00  sec  13.1 GBytes  11.2 Gbits/sec    0            sender
[  5]   0.00-10.00  sec  13.1 GBytes  11.2 Gbits/sec                  receiver

iperf Done.

root@OpenWrt:~# ubus call system board
{
        "kernel": "6.6.121",
        "hostname": "OpenWrt",
        "system": "ARMv8 Processor rev 4",
        "model": "ASUS TUF-AX4200",
        "board_name": "asus,tuf-ax4200",
        "rootfs_type": "squashfs",
        "release": {
                "distribution": "OpenWrt",
                "version": "24.10-SNAPSHOT",
                "revision": "r29101-8843108ff0",
                "target": "mediatek/filogic",
                "description": "OpenWrt 24.10-SNAPSHOT r29101-8843108ff0",
                "builddate": "1768782016"
        }
}


root@OpenWrt:~# iperf3 -s -D && iperf3 -c 127.0.0.1
Connecting to host 127.0.0.1, port 5201
[  5] local 127.0.0.1 port 43272 connected to 127.0.0.1 port 5201
[ ID] Interval           Transfer     Bitrate         Retr  Cwnd
[  5]   0.00-1.00   sec  1.05 GBytes  9.02 Gbits/sec    0    639 KBytes       
[  5]   1.00-2.00   sec   793 MBytes  6.65 Gbits/sec    0   1.12 MBytes       
[  5]   2.00-3.00   sec   700 MBytes  5.87 Gbits/sec    0   1.12 MBytes       
[  5]   3.00-4.00   sec   714 MBytes  5.99 Gbits/sec    0   1.12 MBytes       
[  5]   4.00-5.00   sec   684 MBytes  5.73 Gbits/sec    0   1.12 MBytes       
[  5]   5.00-6.00   sec   696 MBytes  5.84 Gbits/sec    0   1.12 MBytes       
[  5]   6.00-7.00   sec   718 MBytes  6.02 Gbits/sec    0   1.12 MBytes       
[  5]   7.00-8.00   sec   681 MBytes  5.71 Gbits/sec    0   1.12 MBytes       
[  5]   8.00-9.00   sec   714 MBytes  5.99 Gbits/sec    0   1.12 MBytes       
[  5]   9.00-10.00  sec   699 MBytes  5.86 Gbits/sec    0   1.12 MBytes       
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bitrate         Retr
[  5]   0.00-10.00  sec  7.30 GBytes  6.27 Gbits/sec    0             sender
[  5]   0.00-10.00  sec  7.30 GBytes  6.27 Gbits/sec                  receiver

iperf Done.

ambrozy5 · 2026-03-22 23:38:36

ambrozy5
Użytkownik
Nieaktywny

Zarejestrowany: 2015-01-27
Posty: 2,429

Odp: Ciekawy test przepustowości iperf3 routera samego ze sobą :)

troche to jak jabłko do cydru... coś ogólnie na amd ten test jak i ten od wg dużo gorzej wypadają niż by się wydawało.

iperf3 -s -D && iperf3 -c 127.0.0.1
Connecting to host 127.0.0.1, port 5201
[ 5] local 127.0.0.1 port 48300 connected to 127.0.0.1 port 5201
[ ID] Interval Transfer Bitrate Retr Cwnd
[ 5] 0.00-1.00 sec 3.70 GBytes 31.7 Gbits/sec 0 1.06 MBytes
[ 5] 1.00-2.00 sec 3.67 GBytes 31.5 Gbits/sec 0 1.06 MBytes
[ 5] 2.00-3.00 sec 3.91 GBytes 33.6 Gbits/sec 0 1.06 MBytes
[ 5] 3.00-4.00 sec 3.71 GBytes 31.8 Gbits/sec 0 1.06 MBytes
[ 5] 4.00-5.00 sec 3.66 GBytes 31.4 Gbits/sec 0 1.06 MBytes
[ 5] 5.00-6.00 sec 3.70 GBytes 31.8 Gbits/sec 0 1.06 MBytes
[ 5] 6.00-7.00 sec 3.64 GBytes 31.2 Gbits/sec 0 1.06 MBytes
[ 5] 7.00-8.00 sec 3.72 GBytes 32.0 Gbits/sec 0 1.06 MBytes
[ 5] 8.00-9.00 sec 3.55 GBytes 30.5 Gbits/sec 0 1.06 MBytes
[ 5] 9.00-10.00 sec 3.46 GBytes 29.7 Gbits/sec 0 1.06 MBytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-10.00 sec 37.9 GBytes 32.5 Gbits/sec 0 sender
[ 5] 0.00-10.00 sec 37.9 GBytes 32.5 Gbits/sec receiver

iperf Done.

thinkpad t14 g3 amd ryzen 5650u cachy os , procek 12 -15% zużycia.

a tu przy 100% zużycia

❯ iperf3 -s -D && iperf3 -c 127.0.0.1 -P 32

[SUM]   0.00-10.00  sec  90.5 GBytes  77.7 Gbits/sec  416             sender
[SUM]   0.00-10.00  sec  90.5 GBytes  77.7 Gbits/sec                  receiver

iperf Done.

❯ iperf3 -s -D && iperf3 -c 127.0.0.1 -P 6
Connecting to host 127.0.0.1, port 5201

- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bitrate         Retr
[  5]   0.00-10.00  sec  26.1 GBytes  22.4 Gbits/sec    0            sender
[  5]   0.00-10.00  sec  26.1 GBytes  22.4 Gbits/sec                  receiver
[  7]   0.00-10.00  sec  26.7 GBytes  22.9 Gbits/sec    0            sender
[  7]   0.00-10.00  sec  26.7 GBytes  22.9 Gbits/sec                  receiver
[  9]   0.00-10.00  sec  26.7 GBytes  22.9 Gbits/sec    0            sender
[  9]   0.00-10.00  sec  26.7 GBytes  22.9 Gbits/sec                  receiver
[ 11]   0.00-10.00  sec  26.2 GBytes  22.5 Gbits/sec    0            sender
[ 11]   0.00-10.00  sec  26.2 GBytes  22.5 Gbits/sec                  receiver
[ 13]   0.00-10.00  sec  26.5 GBytes  22.8 Gbits/sec    0            sender
[ 13]   0.00-10.00  sec  26.5 GBytes  22.8 Gbits/sec                  receiver
[ 15]   0.00-10.00  sec  26.5 GBytes  22.7 Gbits/sec    0            sender
[ 15]   0.00-10.00  sec  26.5 GBytes  22.7 Gbits/sec                  receiver
[SUM]   0.00-10.00  sec   159 GBytes   136 Gbits/sec    0             sender
[SUM]   0.00-10.00  sec   159 GBytes   136 Gbits/sec                  receiver

iperf Done.

~ 10s

100Mb/s - 25Gb/s
Podróżne : GL.Inet MT3000 +1TB hdd
Działka : rb260gs 1j wdm 1Gb+ ruckus r310 + nb m5 + kilka kamer ip + panel 285Wp + lifepo4 12v 60Ah .

Payti · 2026-05-13 22:56:39

Payti
Użytkownik
Aktywny

Zarejestrowany: 2012-01-05
Posty: 391

Odp: Ciekawy test przepustowości iperf3 routera samego ze sobą :)

Xiaomi AX3600 kompilacja OpenWRT z NSS FW 12.5:

root@Xiaomi_AX3600 /root [#]# ubus call system board
{
        "kernel": "6.12.79",
        "hostname": "Xiaomi_AX3600",
        "system": "ARMv8 Processor rev 4",
        "model": "Xiaomi AX3600",
        "board_name": "xiaomi,ax3600",
        "rootfs_type": "squashfs",
        "release": {
                "distribution": "OpenWrt",
                "version": "SNAPSHOT",
                "firmware_url": "https://downloads.openwrt.org/",
                "revision": "r0+33880-0e751b1cb2",
                "target": "qualcommax/ipq807x",
                "description": "OpenWrt SNAPSHOT r0+33880-0e751b1cb2",
                "builddate": "1774913675"
        }
}

root@Xiaomi_AX3600 /root [#]# iperf3 -s -D && iperf3 -c 127.0.0.1
Connecting to host 127.0.0.1, port 5201
[  5] local 127.0.0.1 port 52884 connected to 127.0.0.1 port 5201
[ ID] Interval           Transfer     Bitrate         Retr  Cwnd
[  5]   0.00-1.00   sec   794 MBytes  6.66 Gbits/sec    0    895 KBytes       
[  5]   1.00-2.00   sec   816 MBytes  6.84 Gbits/sec    0    895 KBytes       
[  5]   2.00-3.00   sec   816 MBytes  6.84 Gbits/sec    0    895 KBytes       
[  5]   3.00-4.00   sec   813 MBytes  6.81 Gbits/sec    0   1023 KBytes       
[  5]   4.00-5.00   sec   814 MBytes  6.84 Gbits/sec    0    895 KBytes       
[  5]   5.00-6.00   sec   809 MBytes  6.78 Gbits/sec    0    895 KBytes       
[  5]   6.00-7.00   sec   800 MBytes  6.72 Gbits/sec    0    895 KBytes       
[  5]   7.00-8.00   sec   807 MBytes  6.76 Gbits/sec    0    959 KBytes       
[  5]   8.00-9.00   sec   814 MBytes  6.82 Gbits/sec    0    895 KBytes       
[  5]   9.00-10.00  sec   808 MBytes  6.78 Gbits/sec    0    895 KBytes       
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bitrate         Retr
[  5]   0.00-10.00  sec  7.90 GBytes  6.79 Gbits/sec    0            sender
[  5]   0.00-10.00  sec  7.90 GBytes  6.79 Gbits/sec                  receiver

iperf Done.
root@Xiaomi_AX3600 /root [#]#

Xiaomi AX3600 kompilacja OpenWRT z NSS FW 11.4:

root@Xiaomi_AX3600 /root [#]# ubus call system board
{
        "kernel": "6.12.79",
        "hostname": "Xiaomi_AX3600",
        "system": "ARMv8 Processor rev 4",
        "model": "Xiaomi AX3600",
        "board_name": "xiaomi,ax3600",
        "rootfs_type": "squashfs",
        "release": {
                "distribution": "OpenWrt",
                "version": "SNAPSHOT",
                "firmware_url": "https://downloads.openwrt.org/",
                "revision": "r0+33880-0e751b1cb2",
                "target": "qualcommax/ipq807x",
                "description": "OpenWrt SNAPSHOT r0+33880-0e751b1cb2",
                "builddate": "1774913675"
        }
}

root@Xiaomi_AX3600 /root [#]# iperf3 -s -D && iperf3 -c 127.0.0.1
Connecting to host 127.0.0.1, port 5201
[  5] local 127.0.0.1 port 58420 connected to 127.0.0.1 port 5201
[ ID] Interval           Transfer     Bitrate         Retr  Cwnd
[  5]   0.00-1.00   sec   736 MBytes  6.17 Gbits/sec    2    895 KBytes       
[  5]   1.00-2.00   sec   735 MBytes  6.16 Gbits/sec    0    895 KBytes       
[  5]   2.00-3.00   sec   734 MBytes  6.16 Gbits/sec    0   1023 KBytes       
[  5]   3.00-4.00   sec   735 MBytes  6.16 Gbits/sec    0   1023 KBytes       
[  5]   4.00-5.00   sec   735 MBytes  6.17 Gbits/sec    0    895 KBytes       
[  5]   5.00-6.00   sec   735 MBytes  6.17 Gbits/sec    0    895 KBytes       
[  5]   6.00-7.00   sec   772 MBytes  6.47 Gbits/sec    0    895 KBytes       
[  5]   7.00-8.00   sec   794 MBytes  6.66 Gbits/sec    0    895 KBytes       
[  5]   8.00-9.00   sec   804 MBytes  6.74 Gbits/sec    0   1023 KBytes       
[  5]   9.00-10.00  sec   799 MBytes  6.70 Gbits/sec    0    895 KBytes       
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bitrate         Retr
[  5]   0.00-10.00  sec  7.40 GBytes  6.36 Gbits/sec    2            sender
[  5]   0.00-10.00  sec  7.40 GBytes  6.36 Gbits/sec                  receiver

iperf Done.
root@Xiaomi_AX3600 /root [#]#

Banana Pi BPI-R3 + SFP GPON ONT Nokia G-010S-A + LTE FIBOCOM L860-GL-16 (OpenWrt 25.12-SNAPSHOT, kernel 6.12.71)
Zyxel T56 EX5601-T1 (OpenWrt 25.12-SNAPSHOT, kernel 6.12.85)
Xiaomi AX3600 (OpenWrt NSS SNAPSHOT, kernel 6.12.79)
OpenWRT NSS builds for Xiaomi AX3600 by @Payti

kipronar · 2026-05-17 17:03:37

kipronar
Użytkownik
Nieaktywny

Zarejestrowany: 2017-10-22
Posty: 189

Odp: Ciekawy test przepustowości iperf3 routera samego ze sobą :)

Check Point V-80

~# ubus call system board
{
        "kernel": "6.12.87",
        "hostname": "CHECK_POINT_V80",
        "system": "ARMv8 Processor rev 1",
        "model": "Check Point V-80",
        "board_name": "checkpoint,v-80",
        "rootfs_type": "ext4",
        "release": {
                "distribution": "OpenWrt",
                "version": "25.12-SNAPSHOT",
                "firmware_url": "https://downloads.openwrt.org/",
                "revision": "r32944-084cdacf9d",
                "target": "mvebu/cortexa72",
                "description": "OpenWrt 25.12-SNAPSHOT r32944-084cdacf9d",
                "builddate": "1778871507"
        }
}

~# iperf3 -s -D && iperf3 -c 127.0.0.1
Connecting to host 127.0.0.1, port 5201
[  5] local 127.0.0.1 port 51584 connected to 127.0.0.1 port 5201
[ ID] Interval           Transfer     Bitrate         Retr  Cwnd
[  5]   0.00-1.00   sec  1.64 GBytes  14.1 Gbits/sec    0    639 KBytes       
[  5]   1.00-2.00   sec  1.74 GBytes  15.0 Gbits/sec    0   1.12 MBytes       
[  5]   2.00-3.00   sec  1.77 GBytes  15.2 Gbits/sec    0   1.12 MBytes       
[  5]   3.00-4.00   sec  1.78 GBytes  15.3 Gbits/sec    0   1.12 MBytes       
[  5]   4.00-5.00   sec  1.75 GBytes  15.0 Gbits/sec    0   1.12 MBytes       
[  5]   5.00-6.00   sec  1.77 GBytes  15.2 Gbits/sec    0   1.12 MBytes       
[  5]   6.00-7.00   sec  1.75 GBytes  15.1 Gbits/sec    0   1.12 MBytes       
[  5]   7.00-8.00   sec  1.75 GBytes  15.0 Gbits/sec    0   1.12 MBytes       
[  5]   8.00-9.00   sec  1.57 GBytes  13.5 Gbits/sec    0   1.25 MBytes       
[  5]   9.00-10.00  sec  1.73 GBytes  14.8 Gbits/sec    0   1.31 MBytes       
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bitrate         Retr
[  5]   0.00-10.00  sec  17.4 GBytes  15.0 Gbits/sec    0            sender
[  5]   0.00-10.00  sec  17.4 GBytes  15.0 Gbits/sec                  receiver

iperf Done.

Aruba AP-303H

~# ubus call system board
{
        "kernel": "6.12.87",
        "hostname": "ARUBA_AP303H",
        "system": "ARMv7 Processor rev 5 (v7l)",
        "model": "Aruba AP-303H",
        "board_name": "aruba,ap-303h",
        "rootfs_type": "squashfs",
        "release": {
                "distribution": "OpenWrt",
                "version": "25.12-SNAPSHOT",
                "firmware_url": "https://downloads.openwrt.org/",
                "revision": "r32944-084cdacf9d",
                "target": "ipq40xx/generic",
                "description": "OpenWrt 25.12-SNAPSHOT r32944-084cdacf9d",
                "builddate": "1778871507"
        }
}

~# iperf3 -s -D && iperf3 -c 127.0.0.1
Connecting to host 127.0.0.1, port 5201
[  5] local 127.0.0.1 port 50308 connected to 127.0.0.1 port 5201
[ ID] Interval           Transfer     Bitrate         Retr  Cwnd
[  5]   0.00-1.00   sec   185 MBytes  1.55 Gbits/sec    0   2.06 MBytes       
[  5]   1.00-2.00   sec   186 MBytes  1.56 Gbits/sec    0   2.06 MBytes       
[  5]   2.00-3.00   sec   186 MBytes  1.56 Gbits/sec    0   2.06 MBytes       
[  5]   3.00-4.00   sec   178 MBytes  1.50 Gbits/sec    0   2.06 MBytes       
[  5]   4.00-5.00   sec   176 MBytes  1.47 Gbits/sec    0   2.06 MBytes       
[  5]   5.00-6.00   sec   187 MBytes  1.57 Gbits/sec    0   2.06 MBytes       
[  5]   6.00-7.00   sec   197 MBytes  1.65 Gbits/sec    0   2.06 MBytes       
[  5]   7.00-8.00   sec   201 MBytes  1.68 Gbits/sec    0   2.06 MBytes       
[  5]   8.00-9.00   sec   201 MBytes  1.69 Gbits/sec    0   2.06 MBytes       
[  5]   9.00-10.00  sec   201 MBytes  1.68 Gbits/sec    0   2.06 MBytes       
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bitrate         Retr
[  5]   0.00-10.00  sec  1.89 GBytes  1.62 Gbits/sec    0            sender
[  5]   0.00-10.00  sec  1.89 GBytes  1.62 Gbits/sec                  receiver

iperf Done.

jarecki · 2026-05-18 19:00:38

jarecki
Użytkownik
Nieaktywny

Skąd: Silesia
Zarejestrowany: 2012-03-23
Posty: 84

Odp: Ciekawy test przepustowości iperf3 routera samego ze sobą :)

Check Poin v81
ubus call system board
{
"kernel": "6.12.85",
"hostname": "OpenWrt",
"system": "ARMv8 Processor rev 1",
"model": "Check Point V-81",
"board_name": "checkpoint,v-81",
"rootfs_type": "squashfs",
"release": {
"distribution": "OpenWrt",
"version": "25.12-SNAPSHOT",
"firmware_url": "https://downloads.openwrt.org/",
"revision": "r32909-7014bb7ee2",
"target": "mvebu/cortexa72",
"description": "OpenWrt 25.12-SNAPSHOT r32909-7014bb7ee2",
"builddate": "1777760083"
}
}
iperf3 -s -D && iperf3 -c 127.0.0.1
Connecting to host 127.0.0.1, port 5201
[ 5] local 127.0.0.1 port 35904 connected to 127.0.0.1 port 5201
[ ID] Interval Transfer Bitrate Retr Cwnd
[ 5] 0.00-1.00 sec 2.43 GBytes 20.9 Gbits/sec 0 1.31 MBytes
[ 5] 1.00-2.00 sec 2.47 GBytes 21.2 Gbits/sec 0 1.31 MBytes
[ 5] 2.00-3.00 sec 2.48 GBytes 21.3 Gbits/sec 0 1.31 MBytes
[ 5] 3.00-4.00 sec 2.27 GBytes 19.5 Gbits/sec 0 1.31 MBytes
[ 5] 4.00-5.00 sec 2.11 GBytes 18.2 Gbits/sec 0 1.31 MBytes
[ 5] 5.00-6.00 sec 2.15 GBytes 18.5 Gbits/sec 0 1.31 MBytes
[ 5] 6.00-7.00 sec 2.16 GBytes 18.5 Gbits/sec 0 1.31 MBytes
[ 5] 7.00-8.00 sec 2.00 GBytes 17.2 Gbits/sec 0 1.31 MBytes
[ 5] 8.00-9.00 sec 2.11 GBytes 18.2 Gbits/sec 0 1.31 MBytes
[ 5] 9.00-10.00 sec 2.15 GBytes 18.5 Gbits/sec 0 1.31 MBytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-10.00 sec 22.6 GBytes 19.4 Gbits/sec 0 sender
[ 5] 0.00-10.00 sec 22.6 GBytes 19.4 Gbits/sec receiver

iperf Done.

Rób co uważasz, ale uważaj co robisz...

FAQ o OpenWrt | Sprzedam różne routery | Oddam

Ciekawy test przepustowości iperf3 routera samego ze sobą :) (Strona 5 z 5)

Posty: 101 do 119 z 119

101 Odpowiedź przez ambrozy5 2025-07-16 13:54:55

Odp: Ciekawy test przepustowości iperf3 routera samego ze sobą :)

102 Odpowiedź przez Dyziek 2025-07-26 10:18:27 (edytowany przez Dyziek 2025-07-26 10:35:35)

Odp: Ciekawy test przepustowości iperf3 routera samego ze sobą :)

103 Odpowiedź przez tomaszu 2025-09-28 21:32:42 (edytowany przez tomaszu 2025-09-29 21:20:15)

Odp: Ciekawy test przepustowości iperf3 routera samego ze sobą :)

104 Odpowiedź przez bulgar71 2025-11-27 21:44:48 (edytowany przez bulgar71 2025-11-27 21:45:25)

Odp: Ciekawy test przepustowości iperf3 routera samego ze sobą :)

105 Odpowiedź przez Dyziek 2025-11-29 12:36:07

Odp: Ciekawy test przepustowości iperf3 routera samego ze sobą :)

106 Odpowiedź przez andrut 2025-11-30 06:57:00

Odp: Ciekawy test przepustowości iperf3 routera samego ze sobą :)

107 Odpowiedź przez steel_rat 2025-11-30 11:23:11

Odp: Ciekawy test przepustowości iperf3 routera samego ze sobą :)

108 Odpowiedź przez Dyziek 2025-11-30 14:26:59

Odp: Ciekawy test przepustowości iperf3 routera samego ze sobą :)

109 Odpowiedź przez krisux 2025-11-30 18:39:21

Odp: Ciekawy test przepustowości iperf3 routera samego ze sobą :)

110 Odpowiedź przez luckyman 2025-12-02 10:50:02

Odp: Ciekawy test przepustowości iperf3 routera samego ze sobą :)

111 Odpowiedź przez Cezary 2025-12-06 17:04:40

Odp: Ciekawy test przepustowości iperf3 routera samego ze sobą :)

112 Odpowiedź przez tomaszu 2025-12-27 22:15:05

Odp: Ciekawy test przepustowości iperf3 routera samego ze sobą :)

113 Odpowiedź przez mar_w 2025-12-28 18:52:09

Odp: Ciekawy test przepustowości iperf3 routera samego ze sobą :)

114 Odpowiedź przez ambrozy5 2026-03-21 16:53:53 (edytowany przez ambrozy5 2026-03-21 16:59:39)

Odp: Ciekawy test przepustowości iperf3 routera samego ze sobą :)

115 Odpowiedź przez WasylNS 2026-03-22 20:32:19

Odp: Ciekawy test przepustowości iperf3 routera samego ze sobą :)

116 Odpowiedź przez ambrozy5 2026-03-22 23:38:36 (edytowany przez ambrozy5 2026-03-22 23:53:05)

Odp: Ciekawy test przepustowości iperf3 routera samego ze sobą :)

117 Odpowiedź przez Payti 2026-05-13 22:56:39 (edytowany przez Payti 2026-05-17 18:18:01)

Odp: Ciekawy test przepustowości iperf3 routera samego ze sobą :)

118 Odpowiedź przez kipronar 2026-05-17 17:03:37

Odp: Ciekawy test przepustowości iperf3 routera samego ze sobą :)

119 Odpowiedź przez jarecki 2026-05-18 19:00:38

Odp: Ciekawy test przepustowości iperf3 routera samego ze sobą :)

Posty: 101 do 119 z 119