Nie jesteś zalogowany. Proszę się zalogować lub zarejestrować.
eko.one.pl → Oprogramowanie / Software → Gargoyle 1.15.x
Strony Poprzednia 1 2 3 4 5 6 Następna
Zaloguj się lub zarejestruj by napisać odpowiedź
Ale cały czas nie odpowiadasz na pytanie tylko kręcisz się w kółko: plugin to, plugin tamto.
Odpowiedź w końcu na pytanie: masz zainstalowane sterowniki czy nie?
Jak mogę to sprawdzić ?
cat /sys/kernel/debug/usb/devices
Witam, mam problem z obrazami do Asus RP-AC56.
Nie da się wgrać w żaden sposób udostępnionego obrazu (próbowałem przez sysupgrade z openwrt bez luci, przez mtd i przez Asus Firmware Restoration).
W przypadku Asus Firmware Restoration nie wstaje po restarcie i cały czas miga pomarańczowa dioda, w przypadku pozostałych metod nie da sie zapakować pliku do katalogu /tmp ponieważ w połowie przesyłania/pobierania wywala błąd i proces się killuje.
W przypadku obrazów OpenWRT niema problemu z wgraniem.
Dodam, iż posiadam jeszcze Asus RP-AC87 i na nim wgrywanie za pomocą Asus Firmware Restoration idzie bez najmniejszych problemów i Gargoyle wstaje bez problemu.
Czy mogę prosić autora o weryfikacje obrazów do Asus RP-AC56 ?
Jak się proces kilkuje to znaczy że ma za mało wolnego ramu; wyłącz wszystko co możliwe żeby zwolnić ram, łącznie z uhttpd, sambą, dnsmasq itd.
Jak mam zweryfikować obrazy nie posiadając tego modelu? Podaj konkretny link do obrazu który ci działa.
Ok, spróbuje zwolnić miejsce i wgrać obraz do /tmp,ale dziwne jest to, że metodą tftp (Asus Firmware Restoration) nie wgrywa prawidłowo.
Daj mi link do działającego obrazy, wgraj go, pokaż wyniki poleceń
ubus call system board
df -h
mount
i spróbuj zrobić sysupgrade plikiem z gargoyle, koniecznie bez zachowania konfiguracji.
Wgrałem TEN FIRMWARE
Efekty wydanych poleceń:
root@OpenWrt:~# ubus call system board
{
"kernel": "5.15.173",
"hostname": "OpenWrt",
"system": "MediaTek MT7621 ver:1 eco:3",
"model": "Asus RP-AC56",
"board_name": "asus,rp-ac56",
"rootfs_type": "squashfs",
"release": {
"distribution": "OpenWrt",
"version": "23.05-SNAPSHOT",
"revision": "r24149-125a2e1311",
"target": "ramips/mt7621",
"description": "OpenWrt 23.05-SNAPSHOT r24149-125a2e1311"
}
}
root@OpenWrt:~# df -h
Filesystem Size Used Available Use% Mounted on
/dev/root 5.8M 5.8M 0 100% /rom
tmpfs 27.2M 88.0K 27.1M 0% /tmp
tmpfs 27.2M 104.0K 27.1M 0% /tmp/root
tmpfs 512.0K 0 512.0K 0% /dev
/dev/mtdblock6 7.2M 364.0K 6.8M 5% /overlay
overlayfs:/overlay 7.2M 364.0K 6.8M 5% /
root@OpenWrt:~# mount
/dev/root on /rom type squashfs (ro,relatime,errors=continue)
proc on /proc type proc (rw,nosuid,nodev,noexec,noatime)
sysfs on /sys type sysfs (rw,nosuid,nodev,noexec,noatime)
cgroup2 on /sys/fs/cgroup type cgroup2 (rw,nosuid,nodev,noexec,relatime,nsdelegate)
tmpfs on /tmp type tmpfs (rw,nosuid,nodev,noatime)
tmpfs on /tmp/root type tmpfs (rw,noatime,mode=755)
tmpfs on /dev type tmpfs (rw,nosuid,noexec,noatime,size=512k,mode=755)
devpts on /dev/pts type devpts (rw,nosuid,noexec,noatime,mode=600,ptmxmode=000)
debugfs on /sys/kernel/debug type debugfs (rw,noatime)
bpffs on /sys/fs/bpf type bpf (rw,nosuid,nodev,noexec,noatime,mode=700)
/dev/mtdblock6 on /overlay type jffs2 (rw,noatime)
overlayfs:/overlay on / type overlay (rw,noatime,lowerdir=/,upperdir=/overlay/upper,workdir=/overlay/work)Mam nadzieje, że to pomoże Dziękuje za zainteresowanie problemem.
I jak historia? Próbowałeś wgrywać przez sysupgrade?
Pomimo usunięcia większości niepotrzebnych rzeczy, to nie mogę przesłać pliku sysupgrade do \tmp aby spróbować wykonać upgrade.
Ale polecenie "free" pokazuje że jest 27 mb wolnego, a nie jestem w stanie zapisać pliku 7 mb...
Uruchom go w trybie failsafe i wtedy spróbuj.
Jest progres 
Po wgraniu Gargoyle co prawda router nie wstaje w normalnym trybie ale w trybie failsafe mogę się do niego dostać i wyskakuje ekran powitalny Gargoyla.
Czy mogę coś jeszcze zrobić aby router był w stanie uruchomić się normalnie?
Czemu w failsafe? Co wyświetlia/wypisuje?
Właczam router i cały czas miga na pomarańczowo dioda i router sie nei uruchamia normalnie.
W trybie failsafe wyświetla sie to:
Zrób logread i pokaż wynik.
Wyskakuje błąd
Failed to connect to ubus
To dmesg
root@(none):~# dmesg
[ 0.000000] Linux version 5.15.173 (cezary@eko.one.pl) (mipsel-openwrt-linux-musl-gcc (OpenWrt GCC 12.3.0 r0+24153-1292a493a6) 12.3.0, GNU ld (GNU Binutils) 2.40.0) #0 SMP Tue Jan 28 07:36:43 2025
[ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
[ 0.000000] printk: bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[ 0.000000] MIPS: machine is Asus RP-AC56
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] VPE topology {2} total 2
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] percpu: Embedded 12 pages/cpu s17488 r8192 d23472 u49152
[ 0.000000] pcpu-alloc: s17488 r8192 d23472 u49152 alloc=12*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes, linear)
[ 0.000000] Writing ErrCtl register=00020278
[ 0.000000] Readback ErrCtl register=00020278
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 55044K/65536K available (6818K kernel code, 597K rwdata, 856K rodata, 1252K init, 219K bss, 10492K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS: 256
[ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns
[ 0.000003] sched_clock: 64 bits at 880MHz, resolution 1ns, wraps every 4398046511103ns
[ 0.016016] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688)
[ 0.088288] pid_max: default: 32768 minimum: 301
[ 0.098040] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.112447] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.130681] rcu: Hierarchical SRCU implementation.
[ 0.140647] smp: Bringing up secondary CPUs ...
[ 0.150227] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.150251] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.150265] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.150313] CPU1 revision is: 0001992f (MIPS 1004Kc)
[ 0.210318] Synchronize counters for CPU 1: done.
[ 0.270001] smp: Brought up 1 node, 2 CPUs
[ 0.283179] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.302642] futex hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.316222] pinctrl core: initialized pinctrl subsystem
[ 0.328232] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.340659] thermal_sys: Registered thermal governor 'step_wise'
[ 0.347654] FPU Affinity set after 11720 emulations
[ 0.371242] clocksource: Switched to clocksource GIC
[ 0.382512] NET: Registered PF_INET protocol family
[ 0.392292] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.407380] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 0.423897] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.439289] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.454474] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear)
[ 0.468469] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.481255] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.494156] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.508276] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.519447] PCI: CLS 0 bytes, default 32
[ 0.529773] workingset: timestamp_bits=30 max_order=14 bucket_order=0
[ 0.546550] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.558065] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.578432] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 0.595543] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 0.607130] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 0.618597] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 0.630219] mt7621-pci 1e140000.pcie: host bridge /pcie@1e140000 ranges:
[ 0.643542] mt7621-pci 1e140000.pcie: No bus range found for /pcie@1e140000, using [bus 00-ff]
[ 0.660977] mt7621-pci 1e140000.pcie: MEM 0x0060000000..0x006fffffff -> 0x0060000000
[ 0.677197] mt7621-pci 1e140000.pcie: IO 0x001e160000..0x001e16ffff -> 0x0000000000
[ 1.051257] mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK)
[ 1.065042] mt7621-pci 1e140000.pcie: PCIE0 enabled
[ 1.074686] mt7621-pci 1e140000.pcie: PCIE1 enabled
[ 1.084384] PCI coherence region base: 0x60000000, mask/settings: 0xf0000002
[ 1.098532] mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00
[ 1.111089] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 1.121943] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
[ 1.135587] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
[ 1.147904] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400
[ 1.159794] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 1.172231] pci 0000:00:00.0: reg 0x14: [mem 0x00000000-0x0000ffff]
[ 1.184742] pci 0000:00:00.0: supports D1
[ 1.192607] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 1.204863] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400
[ 1.216760] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 1.229171] pci 0000:00:01.0: reg 0x14: [mem 0x00000000-0x0000ffff]
[ 1.241729] pci 0000:00:01.0: supports D1
[ 1.249559] pci 0000:00:01.0: PME# supported from D0 D1 D3hot
[ 1.263178] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 1.279044] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 1.295151] pci 0000:01:00.0: [14c3:7603] type 00 class 0x028000
[ 1.307034] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff]
[ 1.319564] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[ 1.333199] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 1.343504] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff]
[ 1.355577] pci 0000:00:00.0: bridge window [mem 0x00000000-0x000fffff]
[ 1.369061] pci 0000:00:00.0: bridge window [mem 0x00000000-0x000fffff pref]
[ 1.383409] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 1.396800] pci 0000:02:00.0: [14c3:7662] type 00 class 0x028000
[ 1.408685] pci 0000:02:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit]
[ 1.422144] pci 0000:02:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[ 1.435523] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
[ 1.449176] pci 0000:00:01.0: PCI bridge to [bus 02-ff]
[ 1.459488] pci 0000:00:01.0: bridge window [io 0x0000-0x0fff]
[ 1.471554] pci 0000:00:01.0: bridge window [mem 0x00000000-0x000fffff]
[ 1.485037] pci 0000:00:01.0: bridge window [mem 0x00000000-0x000fffff pref]
[ 1.499377] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
[ 1.512563] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[ 1.525642] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[ 1.539466] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000]
[ 1.552595] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000]
[ 1.566428] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
[ 1.579908] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x601fffff pref]
[ 1.594243] pci 0000:00:01.0: BAR 8: assigned [mem 0x60200000-0x602fffff]
[ 1.607727] pci 0000:00:01.0: BAR 9: assigned [mem 0x60300000-0x603fffff pref]
[ 1.622063] pci 0000:00:00.0: BAR 1: assigned [mem 0x60400000-0x6040ffff]
[ 1.635559] pci 0000:00:01.0: BAR 1: assigned [mem 0x60410000-0x6041ffff]
[ 1.649023] pci 0000:00:00.0: BAR 7: assigned [io 0x0000-0x0fff]
[ 1.661121] pci 0000:00:01.0: BAR 7: assigned [io 0x1000-0x1fff]
[ 1.673218] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff]
[ 1.686699] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 1.696546] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff]
[ 1.708641] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
[ 1.722112] pci 0000:00:00.0: bridge window [mem 0x60100000-0x601fffff pref]
[ 1.736468] pci 0000:02:00.0: BAR 0: assigned [mem 0x60200000-0x602fffff 64bit]
[ 1.750983] pci 0000:02:00.0: BAR 6: assigned [mem 0x60300000-0x6030ffff pref]
[ 1.765322] pci 0000:00:01.0: PCI bridge to [bus 02]
[ 1.775167] pci 0000:00:01.0: bridge window [io 0x1000-0x1fff]
[ 1.787259] pci 0000:00:01.0: bridge window [mem 0x60200000-0x602fffff]
[ 1.800742] pci 0000:00:01.0: bridge window [mem 0x60300000-0x603fffff pref]
[ 1.817263] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 1.834015] printk: console [ttyS0] disabled
[ 1.842617] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 16, base_baud = 3125000) is a 16550A
[ 1.860591] printk: console [ttyS0] enabled
[ 1.877103] printk: bootconsole [early0] disabled
[ 1.902133] spi-mt7621 1e000b00.spi: sys_freq: 220000000
[ 1.914984] spi-nor spi0.0: mx25l12805d (16384 Kbytes)
[ 1.925438] 5 fixed-partitions partitions found on MTD device spi0.0
[ 1.938167] OF: Bad cell count for /palmbus@1e000000/spi@b00/flash@0/partitions
[ 1.952766] OF: Bad cell count for /palmbus@1e000000/spi@b00/flash@0/partitions
[ 1.967842] OF: Bad cell count for /palmbus@1e000000/spi@b00/flash@0/partitions
[ 1.982507] OF: Bad cell count for /palmbus@1e000000/spi@b00/flash@0/partitions
[ 1.997527] Creating 5 MTD partitions on "spi0.0":
[ 2.007121] 0x000000000000-0x000000030000 : "u-boot"
[ 2.018025] 0x000000030000-0x000000040000 : "nvram"
[ 2.028742] 0x000000040000-0x000000050000 : "factory"
[ 2.040012] 0x000000050000-0x000000ff0000 : "firmware"
[ 2.052108] 2 uimage-fw partitions found on MTD device firmware
[ 2.064103] Creating 2 MTD partitions on "firmware":
[ 2.074007] 0x000000000000-0x000000288727 : "kernel"
[ 2.083902] mtd: partition "kernel" doesn't end on an erase/write block -- force read-only
[ 2.102013] 0x000000288727-0x000000fa0000 : "rootfs"
[ 2.111950] mtd: partition "rootfs" doesn't start on an erase/write block boundary -- force read-only
[ 2.131190] mtd: setting mtd5 (rootfs) as root device
[ 2.141480] 1 squashfs-split partitions found on MTD device rootfs
[ 2.153894] 0x000000730000-0x000000fa0000 : "rootfs_data"
[ 2.165722] 0x000000ff0000-0x000001000000 : "radio"
[ 2.314051] mt7530-mdio mdio-bus:1f: MT7530 adapts as multi-chip module
[ 2.335960] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 18
[ 2.356106] i2c_dev: i2c /dev entries driver
[ 2.365770] i2c-mt7621 1e000900.i2c: clock 100 kHz
[ 2.378836] NET: Registered PF_INET6 protocol family
[ 2.392241] Segment Routing with IPv6
[ 2.399613] In-situ OAM (IOAM) with IPv6
[ 2.407576] NET: Registered PF_PACKET protocol family
[ 2.417788] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 2.444070] 8021q: 802.1Q VLAN Support v1.8
[ 2.458833] mt7530-mdio mdio-bus:1f: MT7530 adapts as multi-chip module
[ 2.492848] mt7530-mdio mdio-bus:1f: configuring for fixed/rgmii link mode
[ 2.507413] mt7530-mdio mdio-bus:1f: Link is Up - 1Gbps/Full - flow control rx/tx
[ 2.512077] mt7530-mdio mdio-bus:1f lan (uninitialized): PHY [mt7530-0:00] driver [MediaTek MT7530 PHY] (irq=20)
[ 2.546228] DSA: tree 0 setup
[ 2.553678] clk: Disabling unused clocks
[ 2.568527] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[ 2.587080] Freeing unused kernel image (initmem) memory: 1252K
[ 2.598933] This architecture does not have kernel memory protection.
[ 2.611788] Run /sbin/init as init process
[ 2.619928] with arguments:
[ 2.619933] /sbin/init
[ 2.619939] with environment:
[ 2.619944] HOME=/
[ 2.619949] TERM=linux
[ 3.838187] init: Console is alive
[ 3.845638] init: - watchdog -
[ 5.621579] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 5.994423] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 6.012721] init: - preinit -
[ 6.292320] random: procd: uninitialized urandom read (4 bytes read)
[ 7.382128] random: jshn: uninitialized urandom read (4 bytes read)
[ 7.801667] random: jshn: uninitialized urandom read (4 bytes read)
[ 7.835603] random: jshn: uninitialized urandom read (4 bytes read)
[ 8.270017] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
[ 8.291474] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 8.291823] mt7530-mdio mdio-bus:1f lan: configuring for phy/gmii link mode
[ 8.322746] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 11.082952] mt7530-mdio mdio-bus:1f lan: Link is Up - 1Gbps/Full - flow control off
[ 11.082992] IPv6: ADDRCONF(NETDEV_CHANGE): lan: link becomes ready
[ 12.671261] random: crng init done
[ 12.678065] random: 6 urandom warning(s) missed due to ratelimiting
root@(none):~#Wpisz
firstboot
zrestartuj i zobacz czy normalnie się uruchomi.
Niestety od ponad 5 minut miga pomarańczowa dioda i tyle... LAN się nie podnosi...
No to rozbierz, podłącz uart i zobacz co go boli.
Zanim będę miał możliwość wpięcia się na piny wpadło mi jeszcze jedno...
Czy są gdzieś do pobrania pierwsze wersje firmware w wersji 1.15.0.0 do RP-AC56?
Nie. Ale wersję 1.15.0 znajdziesz gdzieś na forum gargoyle, były podawane linki.
Witam. KSMBD nie udostępnia zasobów po nfs. Niby w opcjach się ustawia, ale nie uruchamia nfs. Po ponownym wejściu w ustawienia nfs jest odchaczone.
ksmbd to serwer protokołu smb a nie nfs. nfs realizowany jest przez inne programy.
pokaż
cat /etc/exports
Strony Poprzednia 1 2 3 4 5 6 Następna
Zaloguj się lub zarejestruj by napisać odpowiedź
eko.one.pl → Oprogramowanie / Software → Gargoyle 1.15.x
Forum oparte o PunBB, wspierane przez Informer Technologies, Inc