• Zarejestrowany: 2019-10-10
  • Posty: 26

Temat: Modem Huawei E5783B-230 + D-Link DWR-118 połączenie

Witam. Jestem początkującym w tej dziedzinie.  Chciałbym skutecznie połączyć Huawei E5783B-230 kabelkiem USB do routera D-Link DWR-118 tak, by móc rozprowadzić internet nie tyko przez Wi-fi, ale również po kablu. Posiłkowałem się tematem https://eko.one.pl/forum/viewtopic.php?id=11031 jednak moje starania spełzły na niczym. Proszę o pomoc,  wskazówki ( najlepiej krok po kroku ) i wyrozumiałość.

2 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 106,383

Odp: Modem Huawei E5783B-230 + D-Link DWR-118 połączenie

O ile w/w huawei potrafi działać po kablu usb (bo nie wiem).

Podłącz go po usb do dlinka, zaloguj się przez ssh do dlinka i pokaż na początek wynik polecenia

cat /sys/kernel/debug/usb/devices

Zakładam że masz już na d-linku openwrt czy gargoyle, jeżeli nie to złe forum wybrałeś na takie pytanie.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

3 Odpowiedź przez pspablo

  • Zarejestrowany: 2019-10-10
  • Posty: 26

Odp: Modem Huawei E5783B-230 + D-Link DWR-118 połączenie

Cześć. Nie sądziłem, że tak szybko dostanę odp. O to wynik komendy.

root@OpenWrt:~# cat /sys/kernel/debug/usb/devices

T:  Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=480  MxCh= 1
B:  Alloc=  0/800 us ( 0%), #Int=  0, #Iso=  0
D:  Ver= 2.00 Cls=09(hub  ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=1d6b ProdID=0002 Rev= 4.14
S:  Manufacturer=Linux 4.14.143 ehci_hcd
S:  Product=EHCI Host Controller
S:  SerialNumber=101c0000.ehci
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   4 Ivl=256ms

T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  4 Spd=480  MxCh= 0
D:  Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=12d1 ProdID=1506 Rev= 1.02
S:  Manufacturer=HUAWEI Mobile
S:  Product=HUAWEI Mobile
C:* #Ifs= 3 Cfg#= 1 Atr=c0 MxPwr=  2mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=02 Prot=12 Driver=option
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 1 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=02 Prot=16 Driver=huawei_cdc_ncm
E:  Ad=83(I) Atr=03(Int.) MxPS=  16 Ivl=2ms
I:* If#= 1 Alt= 1 #EPs= 3 Cls=ff(vend.) Sub=02 Prot=16 Driver=huawei_cdc_ncm
E:  Ad=83(I) Atr=03(Int.) MxPS=  16 Ivl=2ms
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=125us

T:  Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=12   MxCh= 1
B:  Alloc=  0/900 us ( 0%), #Int=  0, #Iso=  0
D:  Ver= 1.10 Cls=09(hub  ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=1d6b ProdID=0001 Rev= 4.14
S:  Manufacturer=Linux 4.14.143 ohci_hcd
S:  Product=Generic Platform OHCI controller
S:  SerialNumber=101c1000.ohci
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   2 Ivl=255ms
root@OpenWrt:~#

4 Odpowiedź przez Cezary (edytowany przez Cezary 2019-10-10 15:48:27)

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 106,383

Odp: Modem Huawei E5783B-230 + D-Link DWR-118 połączenie

Możesz sprawdzić czy zadziała przy ustawieniu ncm:
to:  http://eko.one.pl/?p=openwrt-3g#obsugam … ehuaweincm lub to: http://eko.one.pl/?p=openwrt-3g#obsugamodemwwtrybiencm . W ostateczności to : http://eko.one.pl/?p=openwrt-3g#obsugam … ybierasppp
Takie połączenie da się też wyklikać w luci.

Zainstaluj sobie na d-linku mój obraz z luci, tam są już wszystkie wymagane sterowniki, nie będziesz musiał instalować tego ręcznie.

Najpierw sugerował bym podłączyć go pod zwykły komputer z linuksem czy windowsem żebyś zobaczył czy on w ogóle potrafi tak działać po kablu na usb. Bo może tego nie umie (ja mam takiego samsunga).

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

5 Odpowiedź przez pspablo

  • Zarejestrowany: 2019-10-10
  • Posty: 26

Odp: Modem Huawei E5783B-230 + D-Link DWR-118 połączenie

Mam Twój obraz na D-Linku

6 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 106,383

Odp: Modem Huawei E5783B-230 + D-Link DWR-118 połączenie

No to śmiało, skonfiguruj i zobacz co będzie.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

7 Odpowiedź przez pspablo

  • Zarejestrowany: 2019-10-10
  • Posty: 26

Odp: Modem Huawei E5783B-230 + D-Link DWR-118 połączenie

Modem działa po kablu na Win10. Wykrywany jest napęd, z którego instaluje się plik instalacyjny.

8 Odpowiedź przez pspablo

  • Zarejestrowany: 2019-10-10
  • Posty: 26

Odp: Modem Huawei E5783B-230 + D-Link DWR-118 połączenie

Niestety połączenia z netem nie uzyskałem. Po skonfigurowaniu 3 typów połączeń wg tematów jw. nie ma dostępu do internetu. Pojawia się też komunikat Network device is not present. Dorzuciłem w pliku /etc/usb-mode.json pozycję 12d1:1506, ale to też nic nie zmieniło.

9 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 106,383

Odp: Modem Huawei E5783B-230 + D-Link DWR-118 połączenie

Nie, /etc/usb-mode.json w ogóle nie dotykaj. Ustaw każdy typ połączenia i po każdym zrób

ifup wan
logread
ifstatus wan

i pokaż wyniki.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

10 Odpowiedź przez pspablo

  • Zarejestrowany: 2019-10-10
  • Posty: 26

Odp: Modem Huawei E5783B-230 + D-Link DWR-118 połączenie

Obsługa modemu w trybie NCM:
Wyniki poleceń:
root@OpenWrt:~# ifup wan
root@OpenWrt:~# logread
Thu Oct 10 17:01:47 2019 kern.notice kernel: [    0.000000] Linux version 4.14.143 (cezary@eko.one.pl) (gcc version 7.4.0 (OpenWrt GCC 7.4.0 r10196-c4e727f01c)) #0 Sat Sep 14 15:10:41 2019
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.000000] Board has DDR2
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.000000] Analog PMU set to hw control
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.000000] Digital PMU set to hw control
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.000000] SoC Type: MediaTek MT7620A ver:2 eco:6
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.000000] bootconsole [early0] enabled
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.000000] MIPS: machine is D-Link DWR-118 A1
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.000000] Determined physical RAM map:
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.000000]  memory: 04000000 @ 00000000 (usable)
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.000000] Initrd not found or empty - disabling initrd
Thu Oct 10 17:01:47 2019 kern.warn kernel: [    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Thu Oct 10 17:01:47 2019 kern.warn kernel: [    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.000000] Zone ranges:
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.000000]   Normal   [mem 0x0000000000000000-0x0000000003ffffff]
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.000000] Movable zone start for each node
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.000000] Early memory node ranges
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.000000]   node   0: [mem 0x0000000000000000-0x0000000003ffffff]
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
Thu Oct 10 17:01:47 2019 kern.debug kernel: [    0.000000] On node 0 totalpages: 16384
Thu Oct 10 17:01:47 2019 kern.debug kernel: [    0.000000] free_area_init_node: node 0, pgdat 804866f0, node_mem_map 81000040
Thu Oct 10 17:01:47 2019 kern.debug kernel: [    0.000000]   Normal zone: 128 pages used for memmap
Thu Oct 10 17:01:47 2019 kern.debug kernel: [    0.000000]   Normal zone: 0 pages reserved
Thu Oct 10 17:01:47 2019 kern.debug kernel: [    0.000000]   Normal zone: 16384 pages, LIFO batch:3
Thu Oct 10 17:01:47 2019 kern.notice kernel: [    0.000000] random: get_random_bytes called from 0x80489740 with crng_init=0
Thu Oct 10 17:01:47 2019 kern.debug kernel: [    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
Thu Oct 10 17:01:47 2019 kern.debug kernel: [    0.000000] pcpu-alloc: [0] 0
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 16256
Thu Oct 10 17:01:47 2019 kern.notice kernel: [    0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.000000] Writing ErrCtl register=0003e450
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.000000] Readback ErrCtl register=0003e450
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.000000] Memory: 59764K/65536K available (3946K kernel code, 185K rwdata, 504K rodata, 220K init, 215K bss, 5772K reserved, 0K cma-reserved)
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.000000] NR_IRQS: 256
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.000000] CPU Clock: 580MHz
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.000000] systick: enable autosleep mode
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.000000] systick: running - mult: 214748, shift: 32
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.000010] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405115902ns
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.015473] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.087713] pid_max: default: 32768 minimum: 301
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.097100] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.110126] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.129759] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.149234] futex hash table entries: 256 (order: -1, 3072 bytes)
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.161413] pinctrl core: initialized pinctrl subsystem
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.172979] NET: Registered protocol family 16
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.439746] PCI host bridge /pcie@10140000 ranges:
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.449152]  MEM 0x0000000020000000..0x000000002fffffff
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.459523]   IO 0x0000000010160000..0x000000001016ffff
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.487066] rt2880_gpio 10000600.gpio: registering 24 gpios
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.498101] rt2880_gpio 10000600.gpio: registering 24 irq handlers
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.510678] rt2880_gpio 10000638.gpio: registering 16 gpios
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.521681] rt2880_gpio 10000638.gpio: registering 16 irq handlers
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.534251] rt2880_gpio 10000660.gpio: registering 32 gpios
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.545256] rt2880_gpio 10000660.gpio: registering 32 irq handlers
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.557808] rt2880_gpio 10000688.gpio: registering 1 gpios
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.568636] rt2880_gpio 10000688.gpio: registering 1 irq handlers
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.581588] PCI host bridge to bus 0000:00
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.589582] pci_bus 0000:00: root bus resource [mem 0x20000000-0x2fffffff]
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.603302] pci_bus 0000:00: root bus resource [io  0xffffffff]
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.615036] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.628536] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
Thu Oct 10 17:01:47 2019 kern.debug kernel: [    0.644324] pci 0000:00:00.0: [1814:0801] type 01 class 0x060400
Thu Oct 10 17:01:47 2019 kern.debug kernel: [    0.644365] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]
Thu Oct 10 17:01:47 2019 kern.debug kernel: [    0.644379] pci 0000:00:00.0: reg 0x14: [mem 0x00000000-0x0000ffff]
Thu Oct 10 17:01:47 2019 kern.debug kernel: [    0.644453] pci 0000:00:00.0: supports D1
Thu Oct 10 17:01:47 2019 kern.debug kernel: [    0.644464] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.644704] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
Thu Oct 10 17:01:47 2019 kern.debug kernel: [    0.660690] pci 0000:01:00.0: [14c3:7650] type 00 class 0x028000
Thu Oct 10 17:01:47 2019 kern.debug kernel: [    0.660738] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff]
Thu Oct 10 17:01:47 2019 kern.debug kernel: [    0.660869] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
Thu Oct 10 17:01:47 2019 kern.debug kernel: [    0.661095] pci 0000:01:00.1: [14c3:8650] type 00 class 0x0d1100
Thu Oct 10 17:01:47 2019 kern.debug kernel: [    0.661137] pci 0000:01:00.1: reg 0x10: [mem 0x00000000-0x000fffff]
Thu Oct 10 17:01:47 2019 kern.debug kernel: [    0.661263] pci 0000:01:00.1: supports D1
Thu Oct 10 17:01:47 2019 kern.debug kernel: [    0.661272] pci 0000:01:00.1: PME# supported from D0 D1 D3hot D3cold
Thu Oct 10 17:01:47 2019 kern.debug kernel: [    0.661464] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
Thu Oct 10 17:01:47 2019 kern.debug kernel: [    0.661481] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 01
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.661535] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.674595] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.688404] pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x201fffff]
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.701904] pci 0000:00:00.0: BAR 1: assigned [mem 0x20200000-0x2020ffff]
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.715415] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff]
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.728912] pci 0000:01:00.1: BAR 0: assigned [mem 0x20100000-0x201fffff]
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.742408] pci 0000:00:00.0: PCI bridge to [bus 01]
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.752252] pci 0000:00:00.0:   bridge window [mem 0x20000000-0x201fffff]
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.771173] clocksource: Switched to clocksource systick
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.782768] NET: Registered protocol family 2
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.792275] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.806057] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.818646] TCP: Hash tables configured (established 1024 bind 1024)
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.831425] UDP hash table entries: 256 (order: 0, 4096 bytes)
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.842954] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.855621] NET: Registered protocol family 1
Thu Oct 10 17:01:47 2019 kern.debug kernel: [    0.864247] PCI: CLS 0 bytes, default 32
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.866874] rt-timer 10000100.timer: maximum frequency is 1220Hz
Thu Oct 10 17:01:47 2019 kern.warn kernel: [    0.879579] Crashlog allocated RAM at address 0x3f00000
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.891645] workingset: timestamp_bits=30 max_order=14 bucket_order=0
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.909816] squashfs: version 4.0 (2009/01/31) Phillip Lougher
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.921318] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.950611] io scheduler noop registered
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.958317] io scheduler deadline registered (default)
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.969370] gpio-export gpio_export: 1 gpio(s) exported
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.979923] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
Thu Oct 10 17:01:47 2019 kern.info kernel: [    0.995157] console [ttyS0] disabled
Thu Oct 10 17:01:47 2019 kern.info kernel: [    1.002216] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
Thu Oct 10 17:01:47 2019 kern.info kernel: [    1.021893] console [ttyS0] enabled
Thu Oct 10 17:01:47 2019 kern.info kernel: [    1.035702] bootconsole [early0] disabled
Thu Oct 10 17:01:47 2019 kern.warn kernel: [    1.059445] spi spi0.0: force spi mode3
Thu Oct 10 17:01:47 2019 kern.info kernel: [    1.078549] m25p80 spi0.0: w25q128 (16384 Kbytes)
Thu Oct 10 17:01:47 2019 kern.notice kernel: [    1.087993] 3 fixed-partitions partitions found on MTD device spi0.0
Thu Oct 10 17:01:47 2019 kern.notice kernel: [    1.100668] Creating 3 MTD partitions on "spi0.0":
Thu Oct 10 17:01:47 2019 kern.notice kernel: [    1.110243] 0x000000000000-0x000000010000 : "jboot"
Thu Oct 10 17:01:47 2019 kern.notice kernel: [    1.120819] 0x000000010000-0x000000ff0000 : "firmware"
Thu Oct 10 17:01:47 2019 kern.notice kernel: [    1.133429] 2 jimage-fw partitions found on MTD device firmware
Thu Oct 10 17:01:47 2019 kern.notice kernel: [    1.145295] Creating 2 MTD partitions on "firmware":
Thu Oct 10 17:01:47 2019 kern.notice kernel: [    1.155208] 0x000000000000-0x00000017f6da : "kernel"
Thu Oct 10 17:01:47 2019 kern.notice kernel: [    1.165974] 0x00000017f6da-0x000000fe0000 : "rootfs"
Thu Oct 10 17:01:47 2019 kern.notice kernel: [    1.176648] mtd: device 3 (rootfs) set to be root filesystem
Thu Oct 10 17:01:47 2019 kern.notice kernel: [    1.189433] 1 squashfs-split partitions found on MTD device rootfs
Thu Oct 10 17:01:47 2019 kern.notice kernel: [    1.201824] 0x0000006f3000-0x000000fe0000 : "rootfs_data"
Thu Oct 10 17:01:47 2019 kern.notice kernel: [    1.213443] 0x000000ff0000-0x000001000000 : "config"
Thu Oct 10 17:01:47 2019 kern.info kernel: [    1.224984] libphy: Fixed MDIO Bus: probed
Thu Oct 10 17:01:47 2019 kern.info kernel: [    1.242253] gsw: setting port4 to gmac mode
Thu Oct 10 17:01:47 2019 kern.err kernel: [    1.250640] mtk_soc_eth 10100000.ethernet: generated random MAC address 1a:69:7b:43:a8:37
Thu Oct 10 17:01:47 2019 kern.info kernel: [    1.267123] libphy: mdio: probed
Thu Oct 10 17:01:47 2019 kern.info kernel: [    1.308111] mtk_soc_eth 10100000.ethernet: connected port 4 to PHY at mdio-bus:04 [uid=02430d91, driver=ICPlus IP1001]
Thu Oct 10 17:01:47 2019 kern.info kernel: [    1.362682] mtk_soc_eth 10100000.ethernet: connected port 5 to PHY at mdio-bus:05 [uid=02430d91, driver=ICPlus IP1001]
Thu Oct 10 17:01:47 2019 kern.info kernel: [    1.384091] mtk_soc_eth 10100000.ethernet: loaded mt7620 driver
Thu Oct 10 17:01:47 2019 kern.info kernel: [    1.396525] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
Thu Oct 10 17:01:47 2019 kern.info kernel: [    1.413687] rt2880_wdt 10000120.watchdog: Initialized
Thu Oct 10 17:01:47 2019 kern.info kernel: [    1.425068] NET: Registered protocol family 10
Thu Oct 10 17:01:47 2019 kern.info kernel: [    1.438178] Segment Routing with IPv6
Thu Oct 10 17:01:47 2019 kern.info kernel: [    1.445656] NET: Registered protocol family 17
Thu Oct 10 17:01:47 2019 kern.info kernel: [    1.454592] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
Thu Oct 10 17:01:47 2019 kern.info kernel: [    1.480438] 8021q: 802.1Q VLAN Support v1.8
Thu Oct 10 17:01:47 2019 kern.info kernel: [    1.490316] hctosys: unable to open rtc device (rtc0)
Thu Oct 10 17:01:47 2019 kern.info kernel: [    1.506831] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
Thu Oct 10 17:01:47 2019 kern.info kernel: [    1.522147] Freeing unused kernel memory: 220K
Thu Oct 10 17:01:47 2019 kern.warn kernel: [    1.531038] This architecture does not have kernel memory protection.
Thu Oct 10 17:01:47 2019 user.info kernel: [    2.279549] init: Console is alive
Thu Oct 10 17:01:47 2019 user.info kernel: [    2.286673] init: - watchdog -
Thu Oct 10 17:01:47 2019 kern.notice kernel: [    2.522436] random: fast init done
Thu Oct 10 17:01:47 2019 user.info kernel: [    4.149720] kmodloader: loading kernel modules from /etc/modules-boot.d/*
Thu Oct 10 17:01:47 2019 kern.info kernel: [    4.390880] usbcore: registered new interface driver usbfs
Thu Oct 10 17:01:47 2019 kern.info kernel: [    4.401966] usbcore: registered new interface driver hub
Thu Oct 10 17:01:47 2019 kern.info kernel: [    4.412689] usbcore: registered new device driver usb
Thu Oct 10 17:01:47 2019 kern.info kernel: [    4.455207] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Thu Oct 10 17:01:47 2019 kern.notice kernel: [    4.476941] SCSI subsystem initialized
Thu Oct 10 17:01:47 2019 kern.info kernel: [    4.489651] ehci-platform: EHCI generic platform driver
Thu Oct 10 17:01:47 2019 kern.info kernel: [    4.510468] phy phy-usbphy.0: remote usb device wakeup disabled
Thu Oct 10 17:01:47 2019 kern.info kernel: [    4.522292] phy phy-usbphy.0: UTMI 16bit 30MHz
Thu Oct 10 17:01:47 2019 kern.info kernel: [    4.531175] ehci-platform 101c0000.ehci: EHCI Host Controller
Thu Oct 10 17:01:47 2019 kern.info kernel: [    4.542690] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
Thu Oct 10 17:01:47 2019 kern.info kernel: [    4.558606] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
Thu Oct 10 17:01:47 2019 kern.info kernel: [    4.578647] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
Thu Oct 10 17:01:47 2019 kern.info kernel: [    4.592118] hub 1-0:1.0: USB hub found
Thu Oct 10 17:01:47 2019 kern.info kernel: [    4.600033] hub 1-0:1.0: 1 port detected
Thu Oct 10 17:01:47 2019 kern.info kernel: [    4.611350] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
Thu Oct 10 17:01:47 2019 kern.info kernel: [    4.625385] ohci-platform: OHCI generic platform driver
Thu Oct 10 17:01:47 2019 kern.info kernel: [    4.636154] ohci-platform 101c1000.ohci: Generic Platform OHCI controller
Thu Oct 10 17:01:47 2019 kern.info kernel: [    4.649780] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
Thu Oct 10 17:01:47 2019 kern.info kernel: [    4.665675] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
Thu Oct 10 17:01:47 2019 kern.info kernel: [    4.703693] hub 2-0:1.0: USB hub found
Thu Oct 10 17:01:47 2019 kern.info kernel: [    4.711636] hub 2-0:1.0: 1 port detected
Thu Oct 10 17:01:47 2019 kern.info kernel: [    4.727924] usbcore: registered new interface driver usb-storage
Thu Oct 10 17:01:47 2019 kern.info kernel: [    4.742201] usbcore: registered new interface driver uas
Thu Oct 10 17:01:47 2019 user.info kernel: [    4.753659] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
Thu Oct 10 17:01:47 2019 user.info kernel: [    4.772228] init: - preinit -
Thu Oct 10 17:01:47 2019 kern.info kernel: [    5.000327] usb 1-1: new high-speed USB device number 2 using ehci-platform
Thu Oct 10 17:01:47 2019 kern.info kernel: [    5.365184] usb-storage 1-1:1.2: USB Mass Storage device detected
Thu Oct 10 17:01:47 2019 kern.info kernel: [    5.401682] scsi host0: usb-storage 1-1:1.2
Thu Oct 10 17:01:47 2019 kern.notice kernel: [    5.617106] random: procd: uninitialized urandom read (4 bytes read)
Thu Oct 10 17:01:47 2019 kern.notice kernel: [    6.443753] scsi 0:0:0:0: CD-ROM            HUAWEI   Mass Storage     2.31 PQ: 0 ANSI: 2
Thu Oct 10 17:01:47 2019 kern.info kernel: [    6.464213] 8021q: adding VLAN 0 to HW filter on device eth0
Thu Oct 10 17:01:47 2019 kern.info kernel: [    6.857536] mtk_soc_eth 10100000.ethernet eth0: port 4 link up (1000Mbps/Full duplex)
Thu Oct 10 17:01:47 2019 user.info kernel: [    7.711163] mount_root: loading kmods from internal overlay
Thu Oct 10 17:01:47 2019 user.info kernel: [    7.778670] kmodloader: loading kernel modules from //etc/modules-boot.d/*
Thu Oct 10 17:01:47 2019 user.info kernel: [    7.793831] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
Thu Oct 10 17:01:47 2019 kern.notice kernel: [    9.000797] jffs2: notice: (473) jffs2_build_xattr_subsystem: complete building xattr subsystem, 21 of xdatum (2 unchecked, 19 orphan) and 101 of xref (26 dead, 46 orphan) found.
Thu Oct 10 17:01:47 2019 user.info kernel: [    9.033444] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
Thu Oct 10 17:01:47 2019 user.info kernel: [    9.055391] block: extroot: not configured
Thu Oct 10 17:01:47 2019 kern.notice kernel: [    9.488493] jffs2: notice: (471) jffs2_build_xattr_subsystem: complete building xattr subsystem, 21 of xdatum (2 unchecked, 19 orphan) and 101 of xref (26 dead, 46 orphan) found.
Thu Oct 10 17:01:47 2019 user.info kernel: [    9.522201] mount_root: loading kmods from internal overlay
Thu Oct 10 17:01:47 2019 user.info kernel: [    9.582144] kmodloader: loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
Thu Oct 10 17:01:47 2019 user.info kernel: [    9.601967] kmodloader: done loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
Thu Oct 10 17:01:47 2019 user.info kernel: [   10.103140] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
Thu Oct 10 17:01:47 2019 user.info kernel: [   10.124307] block: extroot: not configured
Thu Oct 10 17:01:47 2019 user.info kernel: [   10.133706] mount_root: switching to jffs2 overlay
Thu Oct 10 17:01:47 2019 kern.warn kernel: [   10.192278] overlayfs: upper fs does not support tmpfile.
Thu Oct 10 17:01:47 2019 user.warn kernel: [   10.208614] urandom-seed: Seeding with /etc/urandom.seed
Thu Oct 10 17:01:47 2019 user.info kernel: [   10.375060] procd: - early -
Thu Oct 10 17:01:47 2019 user.info kernel: [   10.380916] procd: - watchdog -
Thu Oct 10 17:01:47 2019 kern.info kernel: [   10.763458] mtk_soc_eth 10100000.ethernet eth0: port 4 link down
Thu Oct 10 17:01:47 2019 user.info kernel: [   11.151960] procd: - watchdog -
Thu Oct 10 17:01:47 2019 user.info kernel: [   11.158580] procd: - ubus -
Thu Oct 10 17:01:47 2019 kern.notice kernel: [   11.489957] random: ubusd: uninitialized urandom read (4 bytes read)
Thu Oct 10 17:01:47 2019 kern.notice kernel: [   11.508746] random: jshn: uninitialized urandom read (4 bytes read)
Thu Oct 10 17:01:47 2019 kern.notice kernel: [   11.522528] random: ubusd: uninitialized urandom read (4 bytes read)
Thu Oct 10 17:01:47 2019 user.info kernel: [   11.546292] procd: - init -
Thu Oct 10 17:01:47 2019 user.err kernel: [   13.481477] urngd: jent-rng init failed, err: 2
Thu Oct 10 17:01:47 2019 user.info kernel: [   13.505626] kmodloader: loading kernel modules from /etc/modules.d/*
Thu Oct 10 17:01:47 2019 kern.info kernel: [   13.564058] tun: Universal TUN/TAP device driver, 1.6
Thu Oct 10 17:01:47 2019 kern.info kernel: [   13.605124] ip6_tables: (C) 2000-2006 Netfilter Core Team
Thu Oct 10 17:01:47 2019 kern.info kernel: [   13.651073] fuse init (API version 7.26)
Thu Oct 10 17:01:47 2019 kern.info kernel: [   13.700241] usbcore: registered new interface driver cdc_acm
Thu Oct 10 17:01:47 2019 kern.info kernel: [   13.711608] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
Thu Oct 10 17:01:47 2019 kern.info kernel: [   13.755896] usbcore: registered new interface driver cdc_wdm
Thu Oct 10 17:01:47 2019 kern.info kernel: [   13.790264] Loading modules backported from Linux version v4.19.66-0-g893af1c79e42
Thu Oct 10 17:01:47 2019 kern.info kernel: [   13.805422] Backport generated by backports.git v4.19.66-1-0-g354501da
Thu Oct 10 17:01:47 2019 kern.info kernel: [   13.856837] ip_tables: (C) 2000-2006 Netfilter Core Team
Thu Oct 10 17:01:47 2019 kern.info kernel: [   13.896854] nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
Thu Oct 10 17:01:47 2019 kern.info kernel: [   14.219714] usbcore: registered new interface driver usblp
Thu Oct 10 17:01:47 2019 kern.info kernel: [   14.260295] usbcore: registered new interface driver usbserial
Thu Oct 10 17:01:47 2019 kern.info kernel: [   14.272112] usbcore: registered new interface driver usbserial_generic
Thu Oct 10 17:01:47 2019 kern.info kernel: [   14.285253] usbserial: USB Serial support registered for generic
Thu Oct 10 17:01:47 2019 kern.info kernel: [   14.348493] wireguard: WireGuard 0.0.20190702 loaded. See www.wireguard.com for information.
Thu Oct 10 17:01:47 2019 kern.info kernel: [   14.365404] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
Thu Oct 10 17:01:47 2019 kern.info kernel: [   14.465375] xt_time: kernel timezone is -0000
Thu Oct 10 17:01:47 2019 kern.info kernel: [   14.494016] usbcore: registered new interface driver cdc_ether
Thu Oct 10 17:01:47 2019 kern.info kernel: [   14.520019] usbcore: registered new interface driver cdc_ncm
Thu Oct 10 17:01:47 2019 kern.info kernel: [   14.724281] huawei_cdc_ncm 1-1:1.1: MAC-Address: 00:1e:10:1f:00:00
Thu Oct 10 17:01:47 2019 kern.info kernel: [   14.736678] huawei_cdc_ncm 1-1:1.1: setting rx_max = 16384
Thu Oct 10 17:01:47 2019 kern.info kernel: [   14.772440] huawei_cdc_ncm 1-1:1.1: NDP will be placed at end of frame for this device.
Thu Oct 10 17:01:47 2019 kern.info kernel: [   14.788748] huawei_cdc_ncm 1-1:1.1: cdc-wdm0: USB WDM device
Thu Oct 10 17:01:47 2019 kern.info kernel: [   14.801082] huawei_cdc_ncm 1-1:1.1 wwan0: register 'huawei_cdc_ncm' at usb-101c0000.ehci-1, Huawei CDC NCM device, 00:1e:10:1f:00:00
Thu Oct 10 17:01:47 2019 kern.info kernel: [   14.825139] usbcore: registered new interface driver huawei_cdc_ncm
Thu Oct 10 17:01:47 2019 kern.info kernel: [   15.049601] PPP generic driver version 2.4.2
Thu Oct 10 17:01:47 2019 kern.info kernel: [   15.075226] NET: Registered protocol family 24
Thu Oct 10 17:01:47 2019 kern.info kernel: [   15.105661] usbcore: registered new interface driver qmi_wwan
Thu Oct 10 17:01:47 2019 kern.info kernel: [   15.134997] usbcore: registered new interface driver rndis_host
Thu Oct 10 17:01:47 2019 kern.info kernel: [   15.192898] usbcore: registered new interface driver sierra
Thu Oct 10 17:01:47 2019 kern.info kernel: [   15.204193] usbserial: USB Serial support registered for Sierra USB modem
Thu Oct 10 17:01:47 2019 kern.info kernel: [   15.254105] usbcore: registered new interface driver sierra_net
Thu Oct 10 17:01:47 2019 kern.info kernel: [   15.294020] usbcore: registered new interface driver cdc_mbim
Thu Oct 10 17:01:47 2019 kern.err kernel: [   15.323799] mt76x0e 0000:01:00.0: card - bus=0x1, slot = 0x0 irq=4
Thu Oct 10 17:01:47 2019 kern.info kernel: [   15.336363] mt76x0e 0000:01:00.0: ASIC revision: 76100002
Thu Oct 10 17:01:47 2019 kern.info kernel: [   15.502533] mt76x0e 0000:01:00.0: Firmware Version: 0.1.00
Thu Oct 10 17:01:47 2019 kern.info kernel: [   15.752724] mt76x0e 0000:01:00.0: EEPROM ver:01 fae:00
Thu Oct 10 17:01:47 2019 kern.debug kernel: [   15.767046] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
Thu Oct 10 17:01:47 2019 kern.info kernel: [   15.793908] usbcore: registered new interface driver option
Thu Oct 10 17:01:47 2019 kern.info kernel: [   15.805210] usbserial: USB Serial support registered for GSM modem (1-port)
Thu Oct 10 17:01:47 2019 kern.info kernel: [   15.819578] option 1-1:1.0: GSM modem (1-port) converter detected
Thu Oct 10 17:01:47 2019 kern.info kernel: [   15.832094] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0
Thu Oct 10 17:01:47 2019 kern.info kernel: [   15.904432] usbcore: registered new interface driver qcserial
Thu Oct 10 17:01:47 2019 kern.info kernel: [   15.916057] usbserial: USB Serial support registered for Qualcomm USB modem
Thu Oct 10 17:01:47 2019 kern.info kernel: [   16.000807] ieee80211 phy1: rt2x00lib_request_eeprom_file: Info - Loading EEPROM data from 'soc_wmac.eeprom'.
Thu Oct 10 17:01:47 2019 kern.info kernel: [   16.052452] ieee80211 phy1: rt2x00_set_rt: Info - RT chipset 6352, rev 0500 detected
Thu Oct 10 17:01:47 2019 kern.info kernel: [   16.067961] ieee80211 phy1: rt2x00_set_rf: Info - RF chipset 7620 detected
Thu Oct 10 17:01:47 2019 kern.debug kernel: [   16.082412] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
Thu Oct 10 17:01:47 2019 user.info kernel: [   16.110562] kmodloader: done loading kernel modules from /etc/modules.d/*
Thu Oct 10 17:01:49 2019 user.notice dnsmasq: DNS rebinding protection is active, will discard upstream RFC1918 responses!
Thu Oct 10 17:01:49 2019 user.notice dnsmasq: Allowing 127.0.0.0/8 responses
Thu Oct 10 17:01:49 2019 user.notice dnsmasq: Allowing RFC1918 responses for domain free.aero2.net.pl
Thu Oct 10 17:01:50 2019 daemon.info dnsmasq[1275]: started, version 2.80 cachesize 150
Thu Oct 10 17:01:50 2019 daemon.info dnsmasq[1275]: DNS service limited to local subnets
Thu Oct 10 17:01:50 2019 daemon.info dnsmasq[1275]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth no-DNSSEC no-ID loop-detect inotify dumpfile
Thu Oct 10 17:01:50 2019 daemon.info dnsmasq[1275]: using local addresses only for domain test
Thu Oct 10 17:01:50 2019 daemon.info dnsmasq[1275]: using local addresses only for domain onion
Thu Oct 10 17:01:50 2019 daemon.info dnsmasq[1275]: using local addresses only for domain localhost
Thu Oct 10 17:01:50 2019 daemon.info dnsmasq[1275]: using local addresses only for domain local
Thu Oct 10 17:01:50 2019 daemon.info dnsmasq[1275]: using local addresses only for domain invalid
Thu Oct 10 17:01:50 2019 daemon.info dnsmasq[1275]: using local addresses only for domain bind
Thu Oct 10 17:01:50 2019 daemon.info dnsmasq[1275]: using local addresses only for domain lan
Thu Oct 10 17:01:50 2019 daemon.warn dnsmasq[1275]: no servers found in /tmp/resolv.conf.auto, will retry
Thu Oct 10 17:01:50 2019 daemon.info dnsmasq[1275]: read /etc/hosts - 4 addresses
Thu Oct 10 17:01:50 2019 daemon.info dnsmasq[1275]: read /tmp/hosts/dhcp.cfg01411c - 0 addresses
Thu Oct 10 17:01:50 2019 authpriv.info dropbear[1308]: Not backgrounding
Thu Oct 10 17:01:52 2019 user.notice : Added device handler type: 8021ad
Thu Oct 10 17:01:52 2019 user.notice : Added device handler type: 8021q
Thu Oct 10 17:01:52 2019 user.notice : Added device handler type: macvlan
Thu Oct 10 17:01:52 2019 user.notice : Added device handler type: veth
Thu Oct 10 17:01:52 2019 user.notice : Added device handler type: bridge
Thu Oct 10 17:01:52 2019 user.notice : Added device handler type: Network device
Thu Oct 10 17:01:52 2019 user.notice : Added device handler type: tunnel
Thu Oct 10 17:01:54 2019 daemon.err block: /dev/mtdblock3 is already mounted on /rom
Thu Oct 10 17:01:54 2019 daemon.err block: /dev/mtdblock4 is already mounted on /overlay
Thu Oct 10 17:01:59 2019 kern.info kernel: [   31.067323] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
Thu Oct 10 17:01:59 2019 kern.info kernel: [   31.079027] 8021q: adding VLAN 0 to HW filter on device eth0
Thu Oct 10 17:01:59 2019 kern.info kernel: [   31.131038] device eth0 entered promiscuous mode
Thu Oct 10 17:01:59 2019 kern.info kernel: [   31.160137] br-lan: port 1(eth0.1) entered blocking state
Thu Oct 10 17:01:59 2019 kern.info kernel: [   31.170976] br-lan: port 1(eth0.1) entered disabled state
Thu Oct 10 17:01:59 2019 kern.info kernel: [   31.182166] device eth0.1 entered promiscuous mode
Thu Oct 10 17:01:59 2019 kern.info kernel: [   31.233364] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
Thu Oct 10 17:01:59 2019 daemon.notice netifd: Interface 'lan' is enabled
Thu Oct 10 17:01:59 2019 daemon.notice netifd: Interface 'lan' is setting up now
Thu Oct 10 17:01:59 2019 daemon.notice netifd: Interface 'lan' is now up
Thu Oct 10 17:01:59 2019 daemon.notice netifd: Interface 'loopback' is enabled
Thu Oct 10 17:01:59 2019 daemon.notice netifd: Interface 'loopback' is setting up now
Thu Oct 10 17:01:59 2019 daemon.notice netifd: Interface 'loopback' is now up
Thu Oct 10 17:01:59 2019 daemon.notice netifd: Interface 'wan' is setting up now
Thu Oct 10 17:02:00 2019 daemon.notice netifd: Network device 'lo' link is up
Thu Oct 10 17:02:00 2019 daemon.notice netifd: Interface 'loopback' has link connectivity
Thu Oct 10 17:02:00 2019 user.notice firewall: Reloading firewall due to ifup of lan (br-lan)
Thu Oct 10 17:02:01 2019 daemon.err odhcpd[1456]: Failed to send to ff02::1%lan@br-lan (Address not available)
Thu Oct 10 17:02:01 2019 daemon.notice netifd: wan (1601): comgt 17:02:01 -> -- Error Report --
Thu Oct 10 17:02:01 2019 daemon.notice netifd: wan (1601): comgt 17:02:01 -> ---->                  ^
Thu Oct 10 17:02:01 2019 daemon.notice netifd: wan (1601): comgt 17:02:01 -> Error @118, line 9, Could not write to COM device. (1)
Thu Oct 10 17:02:01 2019 daemon.notice netifd: wan (1601):
Thu Oct 10 17:02:01 2019 daemon.notice netifd: Network device 'eth0' link is up
Thu Oct 10 17:02:01 2019 kern.info kernel: [   33.334584] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Thu Oct 10 17:02:01 2019 kern.info kernel: [   33.446240] br-lan: port 1(eth0.1) entered blocking state
Thu Oct 10 17:02:01 2019 kern.info kernel: [   33.457070] br-lan: port 1(eth0.1) entered forwarding state
Thu Oct 10 17:02:01 2019 daemon.notice netifd: VLAN 'eth0.1' link is up
Thu Oct 10 17:02:01 2019 daemon.err odhcpd[1456]: Failed to send to fe80::a55a:d81f:d545:bf37%lan@br-lan (Permission denied)
Thu Oct 10 17:02:02 2019 daemon.notice netifd: bridge 'br-lan' link is up
Thu Oct 10 17:02:02 2019 daemon.notice netifd: Interface 'lan' has link connectivity
Thu Oct 10 17:02:02 2019 kern.info kernel: [   33.596128] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
Thu Oct 10 17:02:02 2019 daemon.err odhcpd[1456]: Failed to send to fe80::a55a:d81f:d545:bf37%lan@br-lan (Address not available)
Thu Oct 10 17:02:02 2019 daemon.info dnsmasq[1275]: read /etc/hosts - 4 addresses
Thu Oct 10 17:02:02 2019 daemon.info dnsmasq[1275]: read /tmp/hosts/dhcp.cfg01411c.1647 - 0 addresses
Thu Oct 10 17:02:02 2019 daemon.info dnsmasq[1275]: read /tmp/hosts/odhcpd - 0 addresses
Thu Oct 10 17:02:02 2019 daemon.info dnsmasq[1275]: read /tmp/hosts/dhcp.cfg01411c - 0 addresses
Thu Oct 10 17:02:03 2019 daemon.err odhcpd[1456]: Failed to send to fe80::a55a:d81f:d545:bf37%lan@br-lan (Address not available)
Thu Oct 10 17:02:03 2019 daemon.err odhcpd[1456]: Failed to send to ff02::1%lan@br-lan (Address not available)
Thu Oct 10 17:02:03 2019 kern.info kernel: [   35.233677] mtk_soc_eth 10100000.ethernet eth0: port 4 link up (1000Mbps/Full duplex)
Thu Oct 10 17:02:03 2019 daemon.notice netifd: wan (1601): comgt 17:02:03 -> -- Error Report --
Thu Oct 10 17:02:03 2019 daemon.notice netifd: wan (1601): comgt 17:02:03 -> ---->                    ^
Thu Oct 10 17:02:03 2019 daemon.notice netifd: wan (1601): comgt 17:02:03 -> Error @153, line 10, Could not write to COM device. (1)
Thu Oct 10 17:02:03 2019 daemon.notice netifd: wan (1601):
Thu Oct 10 17:02:03 2019 daemon.notice netifd: wan (1601): Unable to verify PIN
Thu Oct 10 17:02:04 2019 user.notice mac80211: Failed command: iw phy phy1 set antenna 0xffffffff 0xffffffff
Thu Oct 10 17:02:04 2019 daemon.notice netifd: wan (1848): Stopping network wan
Thu Oct 10 17:02:04 2019 daemon.notice netifd: radio1 (1603): command failed: Not supported (-122)
Thu Oct 10 17:02:04 2019 user.notice mac80211: Failed command: iw phy phy1 set distance 0
Thu Oct 10 17:02:04 2019 daemon.notice netifd: radio1 (1603): sh: out of range
Thu Oct 10 17:02:04 2019 user.notice mac80211: Failed command: iw phy phy0 set antenna 0xffffffff 0xffffffff
Thu Oct 10 17:02:05 2019 daemon.notice netifd: radio0 (1602): sh: out of range
Thu Oct 10 17:02:05 2019 user.notice ucitrack: Setting up /etc/config/network reload dependency on /etc/config/dhcp
Thu Oct 10 17:02:05 2019 user.notice ucitrack: Setting up /etc/config/network reload dependency on /etc/config/radvd
Thu Oct 10 17:02:05 2019 user.notice ucitrack: Setting up /etc/config/wireless reload dependency on /etc/config/network
Thu Oct 10 17:02:05 2019 daemon.info dnsmasq[1275]: read /etc/hosts - 4 addresses
Thu Oct 10 17:02:05 2019 daemon.info dnsmasq[1275]: read /tmp/hosts/dhcp.cfg01411c.1647 - 0 addresses
Thu Oct 10 17:02:05 2019 daemon.info dnsmasq[1275]: read /tmp/hosts/odhcpd - 1 addresses
Thu Oct 10 17:02:05 2019 daemon.info dnsmasq[1275]: read /tmp/hosts/dhcp.cfg01411c - 0 addresses
Thu Oct 10 17:02:06 2019 user.notice ucitrack: Setting up /etc/config/firewall reload dependency on /etc/config/luci-splash
Thu Oct 10 17:02:06 2019 user.notice ucitrack: Setting up /etc/config/firewall reload dependency on /etc/config/qos
Thu Oct 10 17:02:06 2019 daemon.notice netifd: wan (1848): sending ->
Thu Oct 10 17:02:06 2019 user.notice ucitrack: Setting up /etc/config/firewall reload dependency on /etc/config/miniupnpd
Thu Oct 10 17:02:07 2019 user.notice ucitrack: Setting up /etc/config/dhcp reload dependency on /etc/config/odhcpd
Thu Oct 10 17:02:07 2019 daemon.err hostapd: Configuration file: /var/run/hostapd-phy1.conf
Thu Oct 10 17:02:07 2019 daemon.err hostapd: Configuration file: /var/run/hostapd-phy0.conf
Thu Oct 10 17:02:08 2019 kern.info kernel: [   38.824326] ieee80211 phy1: rt2800_rf_self_txdc_cal: Info - RF Tx self calibration start
Thu Oct 10 17:02:08 2019 kern.info kernel: [   38.841014] ieee80211 phy1: rt2800_rf_self_txdc_cal: Info - RF Tx self calibration end
Thu Oct 10 17:02:09 2019 daemon.notice netifd: Interface 'wan' is now down
Thu Oct 10 17:02:09 2019 user.notice ucitrack: Setting up non-init /etc/config/fstab reload handler: /sbin/block mount
Thu Oct 10 17:02:10 2019 daemon.info dnsmasq[1275]: exiting on receipt of SIGTERM
Thu Oct 10 17:02:10 2019 user.notice ucitrack: Setting up /etc/config/system reload trigger for non-procd /etc/init.d/led
Thu Oct 10 17:02:10 2019 user.notice ucitrack: Setting up /etc/config/system reload dependency on /etc/config/luci_statistics
Thu Oct 10 17:02:10 2019 user.notice ucitrack: Setting up /etc/config/system reload dependency on /etc/config/dhcp
Thu Oct 10 17:02:13 2019 daemon.notice procd: /etc/rc.d/S96led: setting up led lan
Thu Oct 10 17:02:13 2019 daemon.notice procd: /etc/rc.d/S96led: setting up led wan
Thu Oct 10 17:02:13 2019 daemon.notice procd: /etc/rc.d/S96led: setting up led wifi
Thu Oct 10 17:02:15 2019 kern.info kernel: [   46.906240] ieee80211 phy1: rt2800_loft_iq_calibration: Info - LOFT Calibration Done!
Thu Oct 10 17:02:15 2019 kern.info kernel: [   46.925733] ieee80211 phy1: rt2800_iq_search: Info - IQCalibration Start!
Thu Oct 10 17:02:15 2019 kern.info kernel: [   46.953687] ieee80211 phy1: rt2800_iq_search: Info - IQCalibration Done! CH = 0, (gain= 3, phase= 2)
Thu Oct 10 17:02:15 2019 kern.info kernel: [   46.972804] ieee80211 phy1: rt2800_iq_search: Info - IQCalibration Start!
Thu Oct 10 17:02:15 2019 kern.info kernel: [   47.000704] ieee80211 phy1: rt2800_iq_search: Info - IQCalibration Done! CH = 1, (gain= 0, phase= 0)
Thu Oct 10 17:02:15 2019 kern.info kernel: [   47.018941] ieee80211 phy1: rt2800_loft_iq_calibration: Info - TX IQ Calibration Done!
Thu Oct 10 17:02:15 2019 kern.info kernel: [   47.484695] ieee80211 phy1: rt2800_rxiq_calibration: Info - RXIQ G_imb=2, Ph_rx=-5
Thu Oct 10 17:02:15 2019 kern.info kernel: [   47.510058] ieee80211 phy1: rt2800_rxiq_calibration: Info - RXIQ G_imb=-2, Ph_rx=6
Thu Oct 10 17:02:16 2019 kern.info kernel: [   47.644533] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
Thu Oct 10 17:02:16 2019 daemon.info dnsmasq[2106]: started, version 2.80 cachesize 150
Thu Oct 10 17:02:16 2019 daemon.info dnsmasq[2106]: DNS service limited to local subnets
Thu Oct 10 17:02:16 2019 daemon.info dnsmasq[2106]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth no-DNSSEC no-ID loop-detect inotify dumpfile
Thu Oct 10 17:02:16 2019 daemon.info dnsmasq-dhcp[2106]: DHCP, IP range 192.168.1.100 -- 192.168.1.249, lease time 12h
Thu Oct 10 17:02:16 2019 daemon.info dnsmasq[2106]: using local addresses only for domain test
Thu Oct 10 17:02:16 2019 daemon.info dnsmasq[2106]: using local addresses only for domain onion
Thu Oct 10 17:02:16 2019 daemon.info dnsmasq[2106]: using local addresses only for domain localhost
Thu Oct 10 17:02:16 2019 daemon.info dnsmasq[2106]: using local addresses only for domain local
Thu Oct 10 17:02:16 2019 daemon.info dnsmasq[2106]: using local addresses only for domain invalid
Thu Oct 10 17:02:16 2019 daemon.info dnsmasq[2106]: using local addresses only for domain bind
Thu Oct 10 17:02:16 2019 daemon.info dnsmasq[2106]: using local addresses only for domain lan
Thu Oct 10 17:02:16 2019 daemon.warn dnsmasq[2106]: no servers found in /tmp/resolv.conf.auto, will retry
Thu Oct 10 17:02:16 2019 daemon.info dnsmasq[2106]: read /etc/hosts - 4 addresses
Thu Oct 10 17:02:16 2019 daemon.info dnsmasq[2106]: read /tmp/hosts/odhcpd - 1 addresses
Thu Oct 10 17:02:16 2019 daemon.info dnsmasq[2106]: read /tmp/hosts/dhcp.cfg01411c - 2 addresses
Thu Oct 10 17:02:16 2019 daemon.info dnsmasq-dhcp[2106]: read /etc/ethers - 0 addresses
Thu Oct 10 17:02:16 2019 daemon.info dnsmasq-dhcp[2106]: DHCPREQUEST(br-lan) 192.168.1.173 54:53:ed:3b:0a:60
Thu Oct 10 17:02:16 2019 daemon.info dnsmasq-dhcp[2106]: DHCPACK(br-lan) 192.168.1.173 54:53:ed:3b:0a:60 DESKTOP-J9N4CQ1
Thu Oct 10 17:02:16 2019 daemon.info dnsmasq[2106]: exiting on receipt of SIGTERM
Thu Oct 10 17:02:16 2019 kern.info kernel: [   48.492718] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
Thu Oct 10 17:02:17 2019 daemon.notice hostapd: wlan0: interface state UNINITIALIZED->COUNTRY_UPDATE
Thu Oct 10 17:02:17 2019 daemon.notice hostapd: wlan0: interface state COUNTRY_UPDATE->HT_SCAN
Thu Oct 10 17:02:17 2019 kern.info kernel: [   48.751369] br-wan6: port 1(wlan1) entered blocking state
Thu Oct 10 17:02:17 2019 kern.info kernel: [   48.762234] br-wan6: port 1(wlan1) entered disabled state
Thu Oct 10 17:02:17 2019 kern.info kernel: [   48.774035] device wlan1 entered promiscuous mode
Thu Oct 10 17:02:17 2019 daemon.err hostapd: Using interface wlan0 with hwaddr 00:0c:43:26:60:40 and ssid "T5"
Thu Oct 10 17:02:17 2019 daemon.notice hostapd: wlan1: interface state UNINITIALIZED->COUNTRY_UPDATE
Thu Oct 10 17:02:17 2019 daemon.err hostapd: Using interface wlan1 with hwaddr 6c:72:20:a4:c5:d1 and ssid "T2"
Thu Oct 10 17:02:17 2019 user.notice dnsmasq: DNS rebinding protection is active, will discard upstream RFC1918 responses!
Thu Oct 10 17:02:17 2019 user.notice dnsmasq: Allowing 127.0.0.0/8 responses
Thu Oct 10 17:02:17 2019 user.notice dnsmasq: Allowing RFC1918 responses for domain free.aero2.net.pl
Thu Oct 10 17:02:18 2019 authpriv.info dropbear[2511]: Child connection from 192.168.1.173:62079
Thu Oct 10 17:02:19 2019 daemon.info procd: - init complete -
Thu Oct 10 17:02:20 2019 kern.info kernel: [   51.940561] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
Thu Oct 10 17:02:20 2019 daemon.notice hostapd: wlan0: interface state HT_SCAN->ENABLED
Thu Oct 10 17:02:20 2019 daemon.notice hostapd: wlan0: AP-ENABLED
Thu Oct 10 17:02:20 2019 daemon.notice hostapd: wlan1: interface state COUNTRY_UPDATE->ENABLED
Thu Oct 10 17:02:20 2019 daemon.notice hostapd: wlan1: AP-ENABLED
Thu Oct 10 17:02:20 2019 kern.info kernel: [   52.002723] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
Thu Oct 10 17:02:20 2019 daemon.notice netifd: Network device 'wlan1' link is up
Thu Oct 10 17:02:20 2019 daemon.notice netifd: Network device 'wlan0' link is up
Thu Oct 10 17:02:20 2019 kern.info kernel: [   52.462205] br-lan: port 2(wlan0) entered blocking state
Thu Oct 10 17:02:20 2019 kern.info kernel: [   52.472877] br-lan: port 2(wlan0) entered disabled state
Thu Oct 10 17:02:20 2019 kern.info kernel: [   52.483909] device wlan0 entered promiscuous mode
Thu Oct 10 17:02:20 2019 kern.info kernel: [   52.493573] br-lan: port 2(wlan0) entered blocking state
Thu Oct 10 17:02:20 2019 kern.info kernel: [   52.504208] br-lan: port 2(wlan0) entered forwarding state
Thu Oct 10 17:02:21 2019 daemon.notice netifd: Interface 'wan' is enabled
Thu Oct 10 17:02:21 2019 daemon.notice netifd: Interface 'wan' has link connectivity
Thu Oct 10 17:02:21 2019 authpriv.notice dropbear[2511]: Password auth succeeded for 'root' from 192.168.1.173:62079
Thu Oct 10 17:02:22 2019 daemon.info dnsmasq[2599]: started, version 2.80 cachesize 150
Thu Oct 10 17:02:22 2019 daemon.info dnsmasq[2599]: DNS service limited to local subnets
Thu Oct 10 17:02:22 2019 daemon.info dnsmasq[2599]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth no-DNSSEC no-ID loop-detect inotify dumpfile
Thu Oct 10 17:02:22 2019 daemon.info dnsmasq-dhcp[2599]: DHCP, IP range 192.168.1.100 -- 192.168.1.249, lease time 12h
Thu Oct 10 17:02:22 2019 daemon.info dnsmasq[2599]: using local addresses only for domain test
Thu Oct 10 17:02:22 2019 daemon.info dnsmasq[2599]: using local addresses only for domain onion
Thu Oct 10 17:02:22 2019 daemon.info dnsmasq[2599]: using local addresses only for domain localhost
Thu Oct 10 17:02:22 2019 daemon.info dnsmasq[2599]: using local addresses only for domain local
Thu Oct 10 17:02:22 2019 daemon.info dnsmasq[2599]: using local addresses only for domain invalid
Thu Oct 10 17:02:22 2019 daemon.info dnsmasq[2599]: using local addresses only for domain bind
Thu Oct 10 17:02:22 2019 daemon.info dnsmasq[2599]: using local addresses only for domain lan
Thu Oct 10 17:02:22 2019 daemon.warn dnsmasq[2599]: no servers found in /tmp/resolv.conf.auto, will retry
Thu Oct 10 17:02:22 2019 daemon.info dnsmasq[2599]: read /etc/hosts - 4 addresses
Thu Oct 10 17:02:22 2019 daemon.info dnsmasq[2599]: read /tmp/hosts/odhcpd - 1 addresses
Thu Oct 10 17:02:22 2019 daemon.info dnsmasq[2599]: read /tmp/hosts/dhcp.cfg01411c - 2 addresses
Thu Oct 10 17:02:22 2019 daemon.info dnsmasq-dhcp[2599]: read /etc/ethers - 0 addresses
Thu Oct 10 17:02:23 2019 user.info adblock-3.8.5[2352]: adblock is currently disabled, please set the config option 'adb_enabled' to '1' to use this service
Thu Oct 10 17:02:31 2019 kern.err kernel: [   62.886010] huawei_cdc_ncm 1-1:1.1: Error in flush path: -32
Thu Oct 10 17:02:45 2019 kern.notice kernel: [   67.955795] random: crng init done
Thu Oct 10 17:02:45 2019 kern.notice kernel: [   67.962582] random: 6 urandom warning(s) missed due to ratelimiting
Thu Oct 10 17:05:36 2019 authpriv.info dropbear[2623]: Child connection from 192.168.1.173:62105
Thu Oct 10 17:05:41 2019 authpriv.notice dropbear[2623]: Password auth succeeded for 'root' from 192.168.1.173:62105
Thu Oct 10 17:05:43 2019 daemon.notice netifd: Interface 'wan' is setting up now
Thu Oct 10 17:05:44 2019 daemon.notice hostapd: wlan0: interface state ENABLED->DISABLED
Thu Oct 10 17:05:44 2019 daemon.notice hostapd: wlan0: AP-DISABLED
Thu Oct 10 17:05:44 2019 daemon.notice hostapd: wlan0: CTRL-EVENT-TERMINATING
Thu Oct 10 17:05:44 2019 daemon.notice hostapd: nl80211: deinit ifname=wlan0 disabled_11b_rates=0
Thu Oct 10 17:05:44 2019 daemon.notice netifd: wan (2739): comgt 17:05:44 -> -- Error Report --
Thu Oct 10 17:05:44 2019 daemon.notice netifd: wan (2739): comgt 17:05:44 -> ---->                  ^
Thu Oct 10 17:05:44 2019 daemon.notice netifd: wan (2739): comgt 17:05:44 -> Error @118, line 9, Could not write to COM device. (1)
Thu Oct 10 17:05:44 2019 daemon.notice netifd: wan (2739):
Thu Oct 10 17:05:44 2019 kern.info kernel: [  133.403193] br-lan: port 2(wlan0) entered disabled state
Thu Oct 10 17:05:44 2019 daemon.notice netifd: Network device 'wlan0' link is down
Thu Oct 10 17:05:44 2019 daemon.notice netifd: Interface 'wan' has link connectivity loss
Thu Oct 10 17:05:44 2019 kern.info kernel: [  133.475270] device wlan0 left promiscuous mode
Thu Oct 10 17:05:44 2019 kern.info kernel: [  133.484137] br-lan: port 2(wlan0) entered disabled state
Thu Oct 10 17:05:44 2019 daemon.notice netifd: wan (2776): Stopping network wan
Thu Oct 10 17:05:44 2019 daemon.notice netifd: Interface 'wan' is disabled
Thu Oct 10 17:05:45 2019 user.notice mac80211: Failed command: iw phy phy0 set antenna 0xffffffff 0xffffffff
Thu Oct 10 17:05:45 2019 daemon.notice netifd: radio0 (2789): sh: out of range
Thu Oct 10 17:05:45 2019 daemon.notice netifd: wan (2776): sending ->
Thu Oct 10 17:05:45 2019 daemon.err hostapd: Configuration file: /var/run/hostapd-phy0.conf
Thu Oct 10 17:05:46 2019 kern.info kernel: [  135.371958] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
Thu Oct 10 17:05:46 2019 daemon.notice hostapd: wlan0: interface state UNINITIALIZED->COUNTRY_UPDATE
Thu Oct 10 17:05:46 2019 daemon.notice hostapd: wlan0: interface state COUNTRY_UPDATE->HT_SCAN
Thu Oct 10 17:05:46 2019 daemon.err hostapd: Using interface wlan0 with hwaddr 00:0c:43:26:60:40 and ssid "T5"
Thu Oct 10 17:05:48 2019 daemon.notice netifd: Network device 'wlan0' link is up
Thu Oct 10 17:05:48 2019 daemon.notice hostapd: wlan0: interface state HT_SCAN->ENABLED
Thu Oct 10 17:05:48 2019 daemon.notice hostapd: wlan0: AP-ENABLED
Thu Oct 10 17:05:48 2019 kern.info kernel: [  137.013418] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
Thu Oct 10 17:05:48 2019 kern.info kernel: [  137.276355] br-lan: port 2(wlan0) entered blocking state
Thu Oct 10 17:05:48 2019 kern.info kernel: [  137.287044] br-lan: port 2(wlan0) entered disabled state
Thu Oct 10 17:05:48 2019 kern.info kernel: [  137.298156] device wlan0 entered promiscuous mode
Thu Oct 10 17:05:48 2019 kern.info kernel: [  137.307808] br-lan: port 2(wlan0) entered blocking state
Thu Oct 10 17:05:48 2019 kern.info kernel: [  137.318452] br-lan: port 2(wlan0) entered forwarding state
Thu Oct 10 17:05:48 2019 daemon.notice netifd: Interface 'wan' is enabled
Thu Oct 10 17:05:48 2019 daemon.notice netifd: Interface 'wan' has link connectivity
Thu Oct 10 17:05:49 2019 daemon.notice netifd: Interface 'wan' is now down
Thu Oct 10 17:05:49 2019 daemon.notice netifd: Interface 'wan' is setting up now
Thu Oct 10 17:05:50 2019 daemon.notice netifd: wan (2886): comgt 17:05:50 -> -- Error Report --
Thu Oct 10 17:05:50 2019 daemon.notice netifd: wan (2886): comgt 17:05:50 -> ---->                  ^
Thu Oct 10 17:05:50 2019 daemon.notice netifd: wan (2886): comgt 17:05:50 -> Error @118, line 9, Could not write to COM device. (1)
Thu Oct 10 17:05:50 2019 daemon.notice netifd: wan (2886):
root@OpenWrt:~# ifstatus wan
{
        "up": false,
        "pending": false,
        "available": true,
        "autostart": false,
        "dynamic": false,
        "proto": "ncm",
        "data": {

        },
        "errors": [
                {
                        "subsystem": "ncm",
                        "code": "PIN_FAILED"
                }
        ]
}
root@OpenWrt:~#

11 Odpowiedź przez pspablo

  • Zarejestrowany: 2019-10-10
  • Posty: 26

Odp: Modem Huawei E5783B-230 + D-Link DWR-118 połączenie

Zmiana kodu PIN na "bez cyferek" nic nie dała. Podobnie jak zmiana urządzenia w WAN z wdm na /dev/ttyUSB0.

12 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 106,383

Odp: Modem Huawei E5783B-230 + D-Link DWR-118 połączenie

Zły port ustawiłeś. On nie potrafi się dogadać po nim z modemem. A pin oczywiście masz podać taki jak masz do karty.

gcom -d /dev/ttyUSB0 info

działa?

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

13 Odpowiedź przez pspablo

  • Zarejestrowany: 2019-10-10
  • Posty: 26

Odp: Modem Huawei E5783B-230 + D-Link DWR-118 połączenie

Jak i gdzie ustawić właściwy port?? Nie znam pinu do karty i raczej taki nie był ustawiony. Hasła do ustawień APN nie ma.

14 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 106,383

Odp: Modem Huawei E5783B-230 + D-Link DWR-118 połączenie

Przecież zrobiłeś chyba konfigurację wanu? Tam jest port podawany.

Jak używasz tego modemu skoro nie znasz pinu? Chyba że nie ma pinu w ogóle. Wykonaj w/w polecenie i pokaż co wyszło. I pokaż jeszcze wynik uci show network

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

15 Odpowiedź przez pspablo

  • Zarejestrowany: 2019-10-10
  • Posty: 26

Odp: Modem Huawei E5783B-230 + D-Link DWR-118 połączenie

root@OpenWrt:~# gcom -d /dev/ttyUSB0 info
##### Wireless WAN Modem Configuration #####
Product text:
====
comgt 18:12:00 -> -- Error Report --
comgt 18:12:00 -> ---->                 ^
comgt 18:12:00 -> Error @187, line 10, Could not write to COM device. (1)

root@OpenWrt:~#

Karta jest bezpinowa.

16 Odpowiedź przez pspablo

  • Zarejestrowany: 2019-10-10
  • Posty: 26

Odp: Modem Huawei E5783B-230 + D-Link DWR-118 połączenie

Urządzenie modemowe ustawione jest na /dev/ttyUSB0

17 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 106,383

Odp: Modem Huawei E5783B-230 + D-Link DWR-118 połączenie

Wykonaj w/w polecenie na każdym porcie jaki masz: /dev/ttyUSB* lub /dev/cdc-wdm* Jeżeli nie zadziała - zrób jeszcze

uqmi -d /dev/cdc-wdm0 --get-serving-system

i pokaż czy coś wyszło.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

18 Odpowiedź przez pspablo

  • Zarejestrowany: 2019-10-10
  • Posty: 26

Odp: Modem Huawei E5783B-230 + D-Link DWR-118 połączenie

Jeszcze raz wklepałem....

root@OpenWrt:~# gcom -d /dev/ttyUSB0 info
##### Wireless WAN Modem Configuration #####
Product text:
====
Huawei Technologies Co.,Ltd.
Model: E5783B-230
Revision: 8.0.1.1(H190SP4C983)
IMEI: 862390040156848
+GCAP: +CGSM,+DS,+ES
OK
^DSFLOWRPT:000031BE,00075B5F,0006509A,0000000011E0D45D,000000006DA73F37,00000000,00000000
^RSSI: 25
^CERSSI:0,0,255,-92,-8,1,1,10,127,2,-91,-95,99,99,0,2,99,99,
^ANLEVEL:0,99,25,4,92,8
^HCSQ:"LTE",58,49,106,24
^DSFLOWRPT:000031C0,000087BA,000520F1,0000000011E63630,000000006DB6B79B,00000000,00000000
^DSFLOWRPT:000031C2,0000A42F,000679A3,0000000011E737B4,000000006DC34FDE,00000000,00000000
^DSFLOWRPT:000031C4,0000BF2D,0007643B,0000000011E8E5F9,000000006DD3FEE6,00000000,00000000
^DSFLOWRPT:000031C6,0001A3A5,000F3D2A,0000000011EBDC6F,000000006DF1460D,00000000,00000000
^DSFLOWRPT:000031C8,000307E9,00150C90,0000000011F19C28,000000006E1B6004,00000000,00000000
^RSSI: 27
^CERSSI:0,0,255,-91,-11,1,1,10,127,2,-91,-95,99,99,0,2,99,99,
^ANLEVEL:0,99,27,4,91,11
^HCSQ:"LTE",62,50,106,18
^DSFLOWRPT:000031CA,00061669,00183B21,0000000011F8C249,000000006E44C5E3,00000000,00000000
====
Manufacturer:
IMEI and Serial Number:
Manufacturer's Revision: comgt 18:17:45 -> -- Error Report --
comgt 18:17:45 -> ---->                      ^
comgt 18:17:45 -> Error @982, line 56, String is shorter than second argument. (7)

root@OpenWrt:~#

19 Odpowiedź przez pspablo

  • Zarejestrowany: 2019-10-10
  • Posty: 26

Odp: Modem Huawei E5783B-230 + D-Link DWR-118 połączenie

Brak reakcji na polecenie:   uqmi -d /dev/ttyUSB0  --get-serving-system

20 Odpowiedź przez pspablo

  • Zarejestrowany: 2019-10-10
  • Posty: 26

Odp: Modem Huawei E5783B-230 + D-Link DWR-118 połączenie

root@OpenWrt:~# gcom -d /dev/cdc-wdm0 info
##### Wireless WAN Modem Configuration #####
Product text:
====
comgt 18:29:48 -> -- Error Report --
comgt 18:29:48 -> ---->                 ^
comgt 18:29:48 -> Error @187, line 10, Could not write to COM device. (1)

root@OpenWrt:~#

21 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 106,383

Odp: Modem Huawei E5783B-230 + D-Link DWR-118 połączenie

/dev/ttyUSB bardziej wygląda na interfejs diagnostyczny niż komunikacyjny.

Czy ta mydelniczka ma własne gui?

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

22 Odpowiedź przez pspablo

  • Zarejestrowany: 2019-10-10
  • Posty: 26

Odp: Modem Huawei E5783B-230 + D-Link DWR-118 połączenie

Oczywiście. Co ma sprawdzić?

23 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 106,383

Odp: Modem Huawei E5783B-230 + D-Link DWR-118 połączenie

config interface 'wan'
    option ifname 'wwan0'
    option proto 'dhcp'

Zapisz a później wykonaj
ifup wan


po kilku sekundach zrób:

ifconfig
route -n
logread

I pokaż co wyszło

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

24 Odpowiedź przez pspablo

  • Zarejestrowany: 2019-10-10
  • Posty: 26

Odp: Modem Huawei E5783B-230 + D-Link DWR-118 połączenie

root@OpenWrt:~# config interface 'wan'
-ash: config: not found
root@OpenWrt:~#

25 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 106,383

Odp: Modem Huawei E5783B-230 + D-Link DWR-118 połączenie

To nie sa polecenia to wykonania tylko zawartość sekcji wan w pliku /etc/config/network. Widziałeś to już przecież w poradniku.

     uci del network.wan
     uci set network.wan=interface
     uci set network.wan.proto=dhcp
     uci set network.wan.ifname=wwan0
     uci commit network

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona