26 Odpowiedź przez wojciech_69

  • Zarejestrowany: 2011-03-23
  • Posty: 328

Odp: Easybox 904xDSL

Cezary napisał/a:

Nawet wyświetlacz lcd działa...

a co konkretnie można wyświetlać (czy tylko np zasięg i podłączonych klientów) i czy w każdej chwili można dodawać do wyświetlacza nowe dane (jak np w conky można to konfigurować)?

===========================================
WRT160NL v1 CUR01 with Gargoyle PL  by obsy

TL-MR3420 v2 (MiFi) + E3372h-153 (nie hilink) = Play

27 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 106,450

Odp: Easybox 904xDSL

A co chcesz. To przez lcd4linux się robi, więc możesz wiele: http://eko.one.pl/?p=openwrt-lcd4linux

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

28 Odpowiedź przez edass (edytowany przez edass 2017-10-28 12:41:10)

  • edass
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2012-11-21
  • Posty: 235

Odp: Easybox 904xDSL

kipronar napisał/a:

Katalog z plikami:
https://www.dropbox.com/sh/9ocx54hjll8n … 1-Osa?dl=0

uwagi jak w poście #18
dostęp: 192.168.1.1
plik   backup-LEDE-2017-10-23export.tar.gz   zawiera konfigurację:
---- zmiana  dostępu na  192.168.0.1
   hasło ssh i LuCI : L34&$n
   Wi-Fi 2,4  działa, chociaż LuCi pokazuje dziwności (zmienić hasło i uprawnione mac przez ssh)
   DSL ustawiony pod dawny Dialog- wstawić hasło i login

Plik aa.config po przemianowaniu na  .config to konfiguracja tej kompilacji. (Dropbox nie chciał przyjąć go z oryginalną nazwą.)
Uwolnienie drugiego rdzenia jest wyraźnie ponad moje skromne umiejętności.

Cześć
Znowu mam chwilkę czasu aby pobawić się tym routerem więc wgrałem Twoją kompilacje i konfig.
Widzę, że używałeś dodatkowej karty Wifi - zaraz znajdę swoja i użyje jej jako WAN.


--------------EDIT-------------------

Mam już połączenie z internetem ale napotkałem problem z instalacja pakietów- co to oznacza i co mogę z tym zrobić?

root@x904:~# opka update
-ash: opka: not found
root@x904:~# opkg update
Downloading http://downloads.lede-project.org/snapshots/targets/lantiq/xrx200/packages/Packages.gz
Updated list of available packages in /var/opkg-lists/reboot_core
Downloading http://downloads.lede-project.org/snapshots/targets/lantiq/xrx200/packages/Packages.sig
Signature check passed.
Downloading http://downloads.lede-project.org/snapshots/packages/mips_24kc/base/Packages.gz
Updated list of available packages in /var/opkg-lists/reboot_base
Downloading http://downloads.lede-project.org/snapshots/packages/mips_24kc/base/Packages.sig
Signature check passed.
Downloading http://downloads.lede-project.org/snapshots/packages/mips_24kc/easybox904/Packages.gz
*** Failed to download the package list from http://downloads.lede-project.org/snapshots/packages/mips_24kc/easybox904/Packages.gz

Downloading http://downloads.lede-project.org/snapshots/packages/mips_24kc/luci/Packages.gz
Updated list of available packages in /var/opkg-lists/reboot_luci
Downloading http://downloads.lede-project.org/snapshots/packages/mips_24kc/luci/Packages.sig
Signature check passed.
Downloading http://downloads.lede-project.org/snapshots/packages/mips_24kc/packages/Packages.gz
Updated list of available packages in /var/opkg-lists/reboot_packages
Downloading http://downloads.lede-project.org/snapshots/packages/mips_24kc/packages/Packages.sig
Signature check passed.
Downloading http://downloads.lede-project.org/snapshots/packages/mips_24kc/routing/Packages.gz
Updated list of available packages in /var/opkg-lists/reboot_routing
Downloading http://downloads.lede-project.org/snapshots/packages/mips_24kc/routing/Packages.sig
Signature check passed.
Downloading http://downloads.lede-project.org/snapshots/packages/mips_24kc/telephony/Packages.gz
Updated list of available packages in /var/opkg-lists/reboot_telephony
Downloading http://downloads.lede-project.org/snapshots/packages/mips_24kc/telephony/Packages.sig
Signature check passed.
Collected errors:
 * opkg_download: Failed to download http://downloads.lede-project.org/snapshots/packages/mips_24kc/easybox904/Packages.gz, wget returned 8.
root@x904:~# opkg install kmod-usb-printer
Installing kmod-usb-printer (4.9.58-1) to root...
Downloading http://downloads.lede-project.org/snapshots/targets/lantiq/xrx200/packages/kmod-usb-printer_4.9.58-1_mips_24kc.ipk
Collected errors:
 * satisfy_dependencies_for: Cannot satisfy the following dependencies for kmod-usb-printer:
 *      kernel (= 4.9.58-1-ffe6be928b75e0ee3e51d1cfce731d4a) *
 * opkg_install_cmd: Cannot install package kmod-usb-printer.
root@x904:~#
Sprzedam: Tp-link WDR3600 16MB, 4xUSB, OC , Sagemcom Fast 2704 , Tenda AC15 Tomato

Asus RT-AC68U + Huawei 3372 HiLink LTE,   Brother DCP- J125
Nexx WT3020 Gargoyle + webcam Creative Vista! IM

29 Odpowiedź przez kipronar

  • Zarejestrowany: 2017-10-22
  • Posty: 135

Odp: Easybox 904xDSL

W moje kompilacji jest:
kernel - 4.9.54-1-441dff4878ab6cf4e471883f44054904
I chyba w tym problem.
Całkiem świeża kompilacja ze źródła -stan na 26.10- przyniosła porażkę, urządzenie nie startuje.
Nie działa nawet recovery w/g post #280 (https://forum.openwrt.org/viewtopic.php … 6&p=12).
Poczekam na jakiś ruch  ze strony QAuge, drugi router dotrze do mnie za parę dni.

Czy ktoś instalował skutecznie wersję  z dnia 2017-10-26?
(https://app.box.com/s/hvqg535dnubt4r2ontpmtodpvt6ydf00)

30 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 106,450

Odp: Easybox 904xDSL

Ta z 26 ma tylko 7MB, nie działa. Działa ta z 16, która ma 26MB.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

31 Odpowiedź przez kipronar

  • Zarejestrowany: 2017-10-22
  • Posty: 135

Odp: Easybox 904xDSL

Autor mocno wyczyścił .config
Wyciął nawet Asteriska.
Może EasyBox 904xDSL zaistnieje w Lede? 
To tylko spekulacja.
Sądziłem, że wszystko co istotne jednak pozostawił.
Ale czegoś brakło.
Jutro rozłożę zdechlaka i spróbuję reanimować.

@edass
Mogę podesłać dzisiejszą kompilacje w/g sprawdzonego .config i  aktualnych źródeł.
Ale sprawdzić działania nie mam na czym, więc ryzykujesz.

32 Odpowiedź przez verdis

  • verdis
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2017-10-21
  • Posty: 13

Odp: Easybox 904xDSL

U mnie po ponownym zainstalowaniu wersji z 16.10. zadziałało.
Wersja @kipronar także działa.
Czy może ktoś ma potrzebę zrobienia z LAN1 WAN - bardzo bym prosił o tutorial jeśli to zrobił. Lub choć namiastkę podpowiedzi gdzie to robić. A może faktycznie nie ma sensu wykorzystać tego urządzenia w takim trybie.
@edass czy miałeś okazję coś w tej kwestii zrobić - sam sobie nie poradzę.

33 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 106,450

Odp: Easybox 904xDSL

Tutoriale:

WAN

ale nie z lan1 ale z portu oznaczonego "DSL"
- wgrywamy obraz z 16.10
- w pliku /etc/config/network sekcję wan zmieniamy z 

config interface 'wan'
    option ifname 'dsl0'
    option proto 'pppoe'
    option username 'username'
    option password 'password'
    option ipv6 '1'

na

config interface 'wan'
    option ifname eth0.2
    option proto dhcp

- wkładamy kabelek do portu oznaczonego "DSL"
- robimy ifup wan lub restart i działa.

tryb AP z szyfrowaniem PSK2

- /etc/config/wireless ustawiamy np. tak:

config wifi-device 'wl000'
    option type 'ralink'
    option channel '36'
    option disabled '0'

config wifi-iface 'default_wl000'
    option device 'wl000'
    option mode 'ap'
    option ssid 'LEDE5'
    option encryption 'psk2+aes'
    option key '12345678'

config wifi-device 'wl010'
    option type 'ralink'
    option channel '11'
    option disabled '0'

config wifi-iface 'default_wl010'
    option device 'wl010'
    option mode 'ap'
    option ssid 'LEDE2'
    option encryption 'psk2+aes'
    option key '12345678'

Wpisujemy polecenie wifi i mamy AP.

tryb STA

Nie ma i nie działa. Skrypty i sterownik zawarty w tym obrazie wspiera tylko tryb AP i WDS

Mała uwaga: pod żadnym pozorem nie usuwać z network vlanów 66/71 i przypisane ich do lanu, bo nie będzie komunikacji pomiędzy wifi a lanem.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

34 Odpowiedź przez Cezary (edytowany przez Cezary 2017-10-28 21:44:41)

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 106,450

Odp: Easybox 904xDSL

Kilka kolejnych danych:

Temperatura procesora
# awk '{printf "%.01f\n", $1/1000}' /sys/class/hwmon/hwmon0/temp1_input
58.0
Wygaszenie czerwonej LED na panelu
# echo 1 > /sys/class/leds/VGV952CJW33\:red\:power/brightness
Włączenie czerwonej LED na panelu
# echo 0 > /sys/class/leds/VGV952CJW33\:red\:power/brightness
Wyłączenie programowe LCD
# echo 1 > /sys/class/backlight/fb_ili9341_eb904/bl_power

Dotknięcie palcem klawiatury oczywiście włączy znów wyświetlacz

Wyświetlenie danych WANu na LCD w przypadku zmiany z dsl na ethernet
# sed -i 's|ptm0|eth0.2|g' /etc/lcd4linux.conf
Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

35 Odpowiedź przez verdis

  • verdis
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2017-10-21
  • Posty: 13

Odp: Easybox 904xDSL

@Cezary stokrotne dzięki. Także za AP WiFi.
Jeśli da się to zrobić z portu DSL zamiast LAN1 to jeszcze lepiej.
Dla mnie jako "nowego" w tej materii to "kawa na ławę".
Jutro dzień walki ze sprzętem.

36 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 106,450

Odp: Easybox 904xDSL

Da sie, da się. Właśnie tak jestem podłączony.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

37 Odpowiedź przez Cezary (edytowany przez Cezary 2017-10-28 22:02:45)

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 106,450

Odp: Easybox 904xDSL

Obsługa klawiatury

Do dyspozycji masz pięć przycisków: góra, dół, lewo, prawo oraz OK, które generują odpowiednio zdarzenia systemowe KEY_UP, KEY_DOWN, KEY_LEFT, KEY_RIGHT oraz KEY_ENTER. Możemy się do nich podłączyć i podpiąć dowolny skrypt żeby coś się wykonywało po ich naciśnięciu.

# opkg update
# opkg install triggerhappy

Robimy config co przyciski mają robić. Np. góra/dół ma wyłączyć led, lewo/prawo ma włączyć:

# echo "KEY_DOWN 1 echo 1 >  /sys/class/leds/VGV952CJW33:red:power/brightness" >> /etc/triggerhappy/triggers.d/kbd.conf
# echo "KEY_UP 1 echo 1 >  /sys/class/leds/VGV952CJW33:red:power/brightness" >> /etc/triggerhappy/triggers.d/kbd.conf
# echo "KEY_LEFT 1 echo 0 >  /sys/class/leds/VGV952CJW33:red:power/brightness" >> /etc/triggerhappy/triggers.d/kbd.conf
# echo "KEY_RIGHT 1 echo 0 >  /sys/class/leds/VGV952CJW33:red:power/brightness" >> /etc/triggerhappy/triggers.d/kbd.conf

I włączamy proces:

# /etc/init.d/triggerhappy enable
# /etc/init.d/triggerhappy start

Jeżeli nie można zainstalować triggerhappy bo twierdzi że nie ma takiego pakietu to należy sobie odkometować repo reboot_packages w /etc/opkg/distfeeds.conf i zrobić ponownie opkg update.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

38 Odpowiedź przez verdis

  • verdis
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2017-10-21
  • Posty: 13

Odp: Easybox 904xDSL

Ponownie dzięki.
Przyciski jednak zostawiam jako przysłowiową wisienkę na torcie. Muszę najpierw ogarnąć dostęp do eth.
Swoją drogą to ciekawe, że ktoś zajmuje się klawiszami w tym konkretnie routerze na LEDE - musi jednak mieć potencjał.

39 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 106,450

Odp: Easybox 904xDSL

Po prostu moduł jest który realizuje obsługę klawiatury: eb904_keypad. tak samo jak wyświetlacz jest przez framebuffera ogarniany.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

40 Odpowiedź przez kipronar (edytowany przez kipronar 2017-10-28 22:49:02)

  • Zarejestrowany: 2017-10-22
  • Posty: 135

Odp: Easybox 904xDSL

@edass
Dzisiejsza kompilacja:

https://www.dropbox.com/sh/7hmmwo9ti3u1 … kNKLa?dl=0

Zawiera te same pakiety, które były w wersji z dnia 23-10-2017, ale uaktualnione, jest:
kernel - 4.9.58-1-441dff4878ab6cf4e471883f44054904

Uwaga: nie mam możliwości sprawdzenia poprawności pliku.

41 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 106,450

Odp: Easybox 904xDSL

Wyświetlenie obrazka na lcd

Generalnie to jest ekran 320x240 do którego można odwołać się przez framebuffer.  Można by na nim zrobić konsolę, wyświetlić film(!), ale nie ma skompilowanych narzędzi, więc do skromnego wyświetlenia obrazka można wykorzystać... lcd4linux. Ściągamy obrazek:
https://s1.postimg.org/89hjk0le3j/smile.png
Robimy prosty plik konfiguracyjny, np /etc/moje.conf o zawartości:

Widget a {
    class 'Text'
    prefix ''
    Background transparent
}

Widget image {
    class 'Image'
    file '/etc/smile.png'
    update 0
    visible 1
    inverted 0
    reload 0
}

Layout Easybox904xdsl {
 Row01.Col01 'a'
 Layer 2 {
        X1.Y1 'image'
 }
}

Layout 'Easybox904xdsl'

Display SerDispLib {
   Driver  'serdisplib'
   Model   'FRAMEBUFFER'
   Port    'OUT:0'
   Options 'FBDEVICE=/dev/fb0'
}

Display 'SerDispLib'

Obrazek kopiujemy do routera do katalogu /etc pod nazwą smile.png. I odpalamy ręcznie program:

#  lcd4linux -f /etc/moje.conf -q

Lcd4linux wyświetli obrazek i poleci w tło (musi, bo przy wyjściu wyczyści nam framebuffera). Jak chcemy ubić program to po prostu robimy

# killall lcd4linux

Przez zabawą z wyświetlaczem trzeba zatrzymać procesy "systemowe":

# /etc/init.d/lcd4linux stop
# /etc/init.d/lcdController stop
Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

42 Odpowiedź przez kipronar (edytowany przez kipronar 2017-11-01 21:02:18)

  • Zarejestrowany: 2017-10-22
  • Posty: 135

Odp: Easybox 904xDSL

Podczas aktualizacji (LuCI) coś poszło nie tak, potem namotałem bardziej.
Udało sie zrobić recovery w/g postu #280
https://forum.openwrt.org/viewtopic.php … 6&p=12
Przepisałem też u-boot.
System startuje, ale nie jest widoczny  przez sieć, nie da się nawiązać połączenia.
Poprzez picocom widać takie coś:

 ROM VER: 1.1.4
CFG 06
NAND
NAND Read OK
nand_read_page - 00000008
DDR autotuning Rev 0.3c
DDR size from 0xa0000000 - 0xa7ffffff
DDR check ok... start booting...



U-Boot 2010.06-Lv2.0.40-A0.5 (Jan 27 2017 - 20:14:07)

CLOCK CPU 500M RAM 250M
DRAM:  128 MiB
NAND:  NAND device: Manufacturer ID: 0xec, Chip ID: 0xdc (Samsung NAND 512MiB 3,3V 8-bit)
512 MiB
Bad block table found at page 262080, version 0x01
Bad block table found at page 262016, version 0x01
nand_read_bbt: Bad block at 0x0000050e0000
In:    serial
Out:   serial
Err:   serial
Net:   Internal phy(GE) firmware version: 0x040b
vr9 Switch

Type "run flash_nfs" to mount root filesystem over NFS

Hit any key to stop autoboot:  0 
1. bootid : 0, bootnum : 0
2. bootid : 0, bootnum : 1

NAND read: device 0 offset 0x0000000003c40000, size 0x0000000000500000
 0x500000 bytes read: OK
## Booting kernel from Legacy Image at 80800000 ...
   Image Name:   MIPS LEDE Linux-4.9.14
   Created:      2017-03-18  23:25:15 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    5127344 Bytes = 4.9 MiB
   Load Address: 80002000
   Entry Point:  80002000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK

Starting kernel ...

[    0.000000] Linux version 4.9.14 (mueller@OfficePC) (gcc version 5.4.0 (LEDE GCC 5.4.0 r3847-ddca2cb0f0) ) #0 Sat Mar 18 23:25:15 2017
[    0.000000] SoC: xRX200 rev 1.2
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019556 (MIPS 34Kc)
[    0.000000] MIPS: machine is VGV952CJW33-E-IR - EasyBox 904 xDSL
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] User-defined physical RAM map:
[    0.000000]  memory: 07400000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x00000000073fffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x00000000073fffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x00000000073fffff]
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 29464
[    0.000000] Kernel command line: console=ttyLTQ0,115200 ubi.mtd=12,2048 panic=1 DTS-TEST-SEQNO=77 root=ubi0:rootfs rootfstype=ubifs rootdelay=7 mem=116M phym=128M vpe1_load_addr=0x87e00000 vpe1_mem=2M maxvpes=1 maxtcs=1 nosmp
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Writing ErrCtl register=00008900
[    0.000000] Readback ErrCtl register=00008900
[    0.000000] Memory: 107424K/118784K available (4429K kernel code, 191K rwdata, 876K rodata, 4472K init, 226K bss, 11360K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:256
[    0.000000] Setting up vectored interrupts
[    0.000000] arch/mips/lantiq/xway/sysctrl.c:ltq_soc_init:517 LTQ_EBU_BUSCON2: 0x0001d3dd
[    0.000000] arch/mips/lantiq/xway/sysctrl.c:ltq_soc_init:520 LTQ_EBU_BUSCON2: 0x0001d3dd
[    0.000000] CPU Clock: 500MHz
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041786 ns
[    0.000010] sched_clock: 32 bits at 250MHz, resolution 4ns, wraps every 8589934590ns
[    0.007858] Calibrating delay loop... 332.54 BogoMIPS (lpj=665088)
[    0.042324] pid_max: default: 32768 minimum: 301
[    0.047162] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.053731] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.067560] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.077194] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.083410] pinctrl core: initialized pinctrl subsystem
[    0.089261] NET: Registered protocol family 16
[    0.098711] pinctrl-xway 1e100b10.pinmux: Init done
[    0.104220] dma-xway 1e104100.dma: Init done - hw rev: 7, ports: 7, channels: 28
[    0.214934] dcdc-xrx200 1f106a00.dcdc: Core Voltage : 1016 mV
[    0.220696] Can't analyze schedule() prologue at 80450f80
[    0.437261] ifx_pcie_wait_phy_link_up timeout
[    0.652281] ifx_pcie_wait_phy_link_up timeout
[    0.867289] ifx_pcie_wait_phy_link_up timeout
[    1.071906] random: fast init done
[    1.085548] ifx_pcie_wait_phy_link_up timeout
[    1.300555] ifx_pcie_wait_phy_link_up timeout
[    1.304753] pcie_rc_initialize link up failed!!!!!
[    1.337837] gpio-stp-xway 1e100bb0.stp: Init done
[    1.343047] SCSI subsystem initialized
[    1.347137] usbcore: registered new interface driver usbfs
[    1.352638] usbcore: registered new interface driver hub
[    1.357985] usbcore: registered new device driver usb
[    1.364333] clocksource: Switched to clocksource MIPS
[    1.370538] NET: Registered protocol family 2
[    1.375706] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    1.382597] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    1.388979] TCP: Hash tables configured (established 1024 bind 1024)
[    1.395494] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    1.401325] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    1.407868] NET: Registered protocol family 1
[    6.581223] gptu: totally 6 16-bit timers/counters
[    6.586046] gptu: misc_register on minor 63
[    6.590158] gptu: succeeded to request irq 126
[    6.594650] gptu: succeeded to request irq 127
[    6.599163] gptu: succeeded to request irq 128
[    6.603677] gptu: succeeded to request irq 129
[    6.608191] gptu: succeeded to request irq 130
[    6.612708] gptu: succeeded to request irq 131
[    6.620259] lantiq,vmmc 1f103000.vmmc: requested GPIO 499
[    6.625557] lantiq,vmmc 1f103000.vmmc: reserved 1MB at 0x05c00000
[    6.631969] phy-xrx200 gphy-xrx200: requesting lantiq/vr9_phy11g_a2x.bin
[    6.639275] phy-xrx200 gphy-xrx200: booting GPHY0 firmware at 70E0000
[    6.645608] phy-xrx200 gphy-xrx200: booting GPHY1 firmware at 70E0000
[    6.753942] Crashlog allocated RAM at address 0x3f00000
[    6.762937] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[    6.779406] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    6.785129] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    6.810809] io scheduler noop registered
[    6.814616] io scheduler deadline registered (default)
[    6.820540] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112, base_baud = 0) is a lantiq,asc
[    6.829424] console [ttyLTQ0] enabled
[    6.829424] console [ttyLTQ0] enabled
[    6.836761] bootconsole [early0] disabled
[    6.836761] bootconsole [early0] disabled
[    6.846126] gen_nand 14000000.nand-parts: platform_nand_data is missing
[    6.851358] gen_nand: probe of 14000000.nand-parts failed with error -22
[    6.858284] nand: device found, Manufacturer ID: 0xec, Chip ID: 0xdc
[    6.864335] nand: Samsung NAND 512MiB 3,3V 8-bit
[    6.868951] nand: 512 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    6.879840] Bad block table found at page 262080, version 0x01
[    6.884987] Bad block table found at page 262016, version 0x01
[    6.890306] nand_read_bbt: bad block at 0x0000050e0000
[    6.895505] 16 ofpart partitions found on MTD device 14000000.nand-parts
[    6.901937] Creating 16 MTD partitions on "14000000.nand-parts":
[    6.907927] 0x000000000000-0x000000040000 : "uboot"
[    6.914575] 0x000000040000-0x000003c40000 : "rootfs"
[    6.920819] mtd: device 1 (rootfs) set to be root filesystem
[    6.925646] mtdsplit: no squashfs found in "rootfs"
[    6.929988] 0x000003c40000-0x000004140000 : "kernel"
[    6.936725] 0x000004140000-0x000004240000 : "tmp1"
[    6.942153] 0x000004240000-0x000004440000 : "tmp2"
[    6.947631] 0x000004440000-0x000004540000 : "sysconfig"
[    6.953598] 0x000004540000-0x000004640000 : "ubootconfig"
[    6.959697] 0x000004640000-0x000004700000 : "fwdiag"
[    6.965434] 0x000004700000-0x000004a00000 : "lcdimage"
[    6.971305] 0x000004a00000-0x000004b00000 : "mfgconfig"
[    6.977328] 0x000004b00000-0x000004c00000 : "sipdata"
[    6.983127] 0x000004c00000-0x000008c00000 : "voice"
[    6.989374] 0x000008c00000-0x00001be00000 : "ubi"
[    6.997503] 0x00001be00000-0x00001fa00000 : "rootfs2"
[    7.003727] 0x00001fa00000-0x00001ff00000 : "kernel2"
[    7.009576] 0x00001ff00000-0x000020000000 : "mystery"
[    7.017430] libphy: Fixed MDIO Bus: probed
[    7.121731] libphy: lantiq,xrx200-mdio: probed
[    7.232937] Intel XWAY PHY11G (xRX integrated) 0:11: attached PHY driver [Intel XWAY PHY11G (xRX integrated)] (mii_bus:phy_addr=0:11, irq=-1)
[    7.316928] Intel XWAY PHY11G (xRX integrated) 0:13: attached PHY driver [Intel XWAY PHY11G (xRX integrated)] (mii_bus:phy_addr=0:13, irq=-1)
[    7.329822] dwc2 1e101000.ifxhcd: requested GPIO 495
[    7.434411] dwc2 1e101000.ifxhcd: DWC OTG Controller
[    7.438014] dwc2 1e101000.ifxhcd: new USB bus registered, assigned bus number 1
[    7.445296] dwc2 1e101000.ifxhcd: irq 62, io mem 0x00000000
[    7.450838] dwc2 1e101000.ifxhcd: Hardware does not support descriptor DMA mode -
[    7.458282] dwc2 1e101000.ifxhcd: falling back to buffer DMA mode.
[    7.465889] hub 1-0:1.0: USB hub found
[    7.468733] hub 1-0:1.0: 1 port detected
[    7.574620] dwc2 1e106000.ifxhcd: DWC OTG Controller
[    7.578220] dwc2 1e106000.ifxhcd: new USB bus registered, assigned bus number 2
[    7.585508] dwc2 1e106000.ifxhcd: irq 91, io mem 0x00000000
[    7.591049] dwc2 1e106000.ifxhcd: Hardware does not support descriptor DMA mode -
[    7.598494] dwc2 1e106000.ifxhcd: falling back to buffer DMA mode.
[    7.605820] hub 2-0:1.0: USB hub found
[    7.608944] hub 2-0:1.0: 1 port detected
[    7.613280] usbcore: registered new interface driver usb-storage
[    7.718986] ltq-cputemp cputemp@0: Current CPU die temperature: 41.0 °C
[    7.724562] wdt 1f8803f0.watchdog: Init done
[    7.729834] NET: Registered protocol family 17
[    7.733073] 8021q: 802.1Q VLAN Support v1.8
[    7.743411] rtl8367b rtl8367b: using bus lantiq,xrx200-mdio
[    7.747841] rtl8367b rtl8367b: RTL8367RB chip found
[    7.928353] usb 1-1: new high-speed USB device number 2 using dwc2
[    8.141672] usb-storage 1-1:1.0: USB Mass Storage device detected
[    8.147268] scsi host0: usb-storage 1-1:1.0
[    8.348460] lantiq,xrx200-net 1e108000.eth eth0: port 2 got link
[    9.087505] ubi0: attaching mtd12
[    9.185723] scsi 0:0:0:0: Direct-Access     Generic  USB Flash Disk   0.00 PQ: 0 ANSI: 2
[    9.193353] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    9.199190] sd 0:0:0:0: [sda] 1024000 512-byte logical blocks: (524 MB/500 MiB)
[    9.212430] sd 0:0:0:0: [sda] Write Protect is off
[    9.216298] sd 0:0:0:0: [sda] Asking for cache data failed
[    9.221303] sd 0:0:0:0: [sda] Assuming drive cache: write through
[    9.317001]  sda: sda1
[    9.321175] sd 0:0:0:0: [sda] Attached SCSI removable disk
[    9.473761] ubi0: scanning is finished
[    9.491710] ubi0: attached mtd12 (name "ubi", size 306 MiB)
[    9.495878] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    9.502724] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 512
[    9.509424] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[    9.516387] ubi0: good PEBs: 2448, bad PEBs: 0, corrupted PEBs: 0
[    9.522480] ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
[    9.529709] ubi0: max/mean erase counter: 7/3, WL threshold: 4096, image sequence number: 1811818081
[    9.538845] ubi0: available PEBs: 0, total reserved PEBs: 2448, PEBs reserved for bad PEB handling: 80
[    9.548211] ubi0: background thread "ubi_bgt0d" started, P[    9.568038] Freeing unused kernel memory: 4472K (80562000 - 809c0000)
[    9.573067] This architecture does not have kernel memory protection.
[    9.603090] init: Console is alive
[    9.605405] init: - watchdog -
[    9.622841] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    9.629426] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    9.639347] init: - preinit -
Cannot parse config file: No such file or directory
Bootnum: 
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[   12.058150] procd: - early -
[   12.059762] procd: - watchdog -
[   12.691222] procd: - ubus -
[   12.745468] procd: - init -
Please press Enter to activate this console.
[   12.892939] lantiq,xrx200-net 1e108000.eth eth0: port 2 lost link
[   12.973424] kmodloader: loading kernel modules from /etc/modules.d/*
[   12.982020] Infineon Technologies DEU driver version 2.0.0 
[   12.988014] IFX DEU DES initialized (multiblock).
[   12.992360] IFX DEU AES initialized (multiblock).
[   12.996432] IFX DEU ARC4 initialized (multiblock).
[   13.001035] IFX DEU SHA1 initialized.
[   13.004646] IFX DEU MD5 initialized.
[   13.008201] IFX DEU SHA1_HMAC initialized.
[   13.012313] IFX DEU MD5_HMAC initialized.
[   13.020809] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
[   13.073727] xt_time: kernel timezone is -0000
[   13.078943] ip_tables: (C) 2000-2006 Netfilter Core Team
[   13.090990] kmodloader: done loading kernel modules from /etc/modules.d/*
[   20.243865] device eth0 entered promiscuous mode
[   20.264823] br-lan: port 1(eth0.1) entered blocking state
[   20.268852] br-lan: port 1(eth0.1) entered disabled state
[   20.274627] device eth0.1 entered promiscuous mode
[   20.318108] br-lan: port 1(eth0.1) entered blocking state
[   20.322120] br-lan: port 1(eth0.1) entered forwarding state
[   49.040406] random: crng init done



BusyBox v1.26.2 () built-in shell (ash)

     _________
    /        /\      _    ___ ___  ___
   /  LE    /  \    | |  | __|   \| __|
  /    DE  /    \   | |__| _|| |) | _|
 /________/  LE  \  |____|___|___/|___|                      lede-project.org
 \        \   DE /
  \    LE  \    /  -----------------------------------------------------------
   \  DE    \  /    Reboot (SNAPSHOT, r3883-006f634768)
    \________\/    -----------------------------------------------------------

=== WARNING! =====================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.
--------------------------------------------------
root@LEDE:/# mc
/bin/ash: mc: not found
root@LEDE:/# ls
bin      etc      lib      overlay  rom      sbin     tmp      var
dev      init     mnt      proc     root     sys      usr      www

Nagłówek Lede pojawia się po wciśnięciu Enter

A tak przebiega proces recovery przez tftp:
-LCD wyświetla, że sukces  i proponuje OFF/ON, jednak sieć nadal milczy

ROM VER: 1.1.4
CFG 06
NAND
NAND Read OK
nand_read_page - 00000008
DDR autotuning Rev 0.3c
DDR size from 0xa0000000 - 0xa7ffffff
DDR check ok... start booting...



U-Boot 2010.06-Lv2.0.40-A0.5 (Jan 27 2017 - 20:14:07)

CLOCK CPU 500M RAM 250M
DRAM:  128 MiB
NAND:  NAND device: Manufacturer ID: 0xec, Chip ID: 0xdc (Samsung NAND 512MiB 3,3V 8-bit)
512 MiB
Bad block table found at page 262080, version 0x01
Bad block table found at page 262016, version 0x01
nand_read_bbt: Bad block at 0x0000050e0000
In:    serial
Out:   serial
Err:   serial
Net:   Internal phy(GE) firmware version: 0x040b
vr9 Switch

Type "run flash_nfs" to mount root filesystem over NFS

reset button pressed --> 1
reset button pressed --> 2
reset button pressed --> 3
reset button pressed --> 4
reset button pressed --> 5
reset button pressed --> 6
reset button pressed --> 7
enter rescue process ...
Uncompressing LCD bootup images ............... 
NAND read: device 0 offset 0x0000000004700000, size 0x0000000000300000
 0x300000 bytes read: OK
Using vr9 Switch device
TFTP from server 192.168.2.100; our IP address is 192.168.2.1
Filename 'fullimage.img'.
Load address: 0x80800000
Loading: T T T T T T #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #########################
done
Bytes transferred = 5127544 (4e3d78 hex)
verify firmware validation: loadaddr = 0x80800000, filesize = 5127544
firmware is ok !

NAND erase: device 0 offset 0x0000000004440000, size 0x0000000000100000
Erasing at 0x4520000 -- 100% complete.
OK

NAND erase: device 0 offset 0x000000001be00000, size 0x0000000003c00000
Erasing at 0x1f9e0000 -- 100% complete.
OK

NAND erase: device 0 offset 0x000000001fa00000, size 0x0000000000500000
Erasing at 0x1fee0000 -- 100% complete.
OK
Saving Environment to NAND...
Erasing at 0x4560000 -- 100% complete.
done
Image contains header with name [MIPS LEDE fakeroot]
erasing 0x00040000 size 0x03c00000
Erasing at 0x3c20000 -- 100% complete. Cleanmarker written at 0x3c20000.
erase OK
writing to 0x00040000 size 0x00000000
 write 0x00000000 bytes: OK
Erasing at 0x4560000 -- 100% complete.
done
Image contains header with name [MIPS LEDE Linux-4.9.14]
adjust size: from 0x004e3cf0 to 0x004e4000
erasing 0x03c40000 size 0x00500000
Erasing at 0x4120000 -- 100% complete.
erase OK
writing to 0x03c40000 size 0x004e4000
write 0x004e4000 bytes: OK
Erasing at 0x4560000 -- 100% complete.
done

Trochę poprawy ale nadal bez działania.
Wyświetlacz -tabelka-  pracuje.


ROM VER: 1.1.4
CFG 06
NAND
NAND Read OK
nand_read_page - 00000008
DDR autotuning Rev 0.3c
DDR size from 0xa0000000 - 0xa7ffffff
DDR check ok... start booting...



U-Boot 2010.06-Lv2.0.40-A0.5 (Jan 27 2017 - 20:14:07)

CLOCK CPU 500M RAM 250M
DRAM:  128 MiB
NAND:  NAND device: Manufacturer ID: 0xec, Chip ID: 0xdc (Samsung NAND 512MiB 3,3V 8-bit)
512 MiB
Bad block table found at page 262080, version 0x01
Bad block table found at page 262016, version 0x01
nand_read_bbt: Bad block at 0x0000050e0000
In:    serial
Out:   serial
Err:   serial
Net:   Internal phy(GE) firmware version: 0x040b
vr9 Switch

Type "run flash_nfs" to mount root filesystem over NFS

Hit any key to stop autoboot:  0 
Uncompressing LCD bootup images ............... 
NAND read: device 0 offset 0x0000000004700000, size 0x0000000000300000
 0x300000 bytes read: OK
1. bootid : 0, bootnum : 0
2. bootid : 0, bootnum : 1

NAND read: device 0 offset 0x0000000003c40000, size 0x0000000000500000
 0x500000 bytes read: OK
## Booting kernel from Legacy Image at 80800000 ...
   Image Name:   MIPS LEDE Linux-4.9.58
   Created:      2017-10-30  23:43:22 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    2097088 Bytes = 2 MiB
   Load Address: 80002000
   Entry Point:  80002000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK

Starting kernel ...

[    0.000000] Linux version 4.9.58 (leszek@linux-4l00) (gcc version 6.3.0 (LEDE GCC 6.3.0 r4939-7c4e3157fe) ) #0 SMP Mon Oct 30 23:43:22 2017
[    0.000000] SoC: xRX200 rev 1.2
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019556 (MIPS 34Kc)
[    0.000000] MIPS: machine is VGV952CJW33-E-IR - EasyBox 904 xDSL
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] User-defined physical RAM map:
[    0.000000]  memory: 07400000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Detected 1 available secondary CPU(s)
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x00000000073fffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x00000000073fffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x00000000073fffff]
[    0.000000] percpu: Embedded 13 pages/cpu @810f5000 s21616 r8192 d23440 u53248
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 29464
[    0.000000] Kernel command line: console=ttyLTQ0,115200 ubi.mtd=12,2048 panic=1 DTS-TEST-SEQNO=77 root=ubi0:rootfs rootfstype=ubifs rootdelay=7 mem=116M phym=128M vpe1_load_addr=0x87e00000 vpe1_mem=2M maxvpes=1 maxtcs=1 nosmp
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Writing ErrCtl register=00017dd0
[    0.000000] Readback ErrCtl register=00017dd0
[    0.000000] Memory: 109636K/118784K available (4890K kernel code, 190K rwdata, 1320K rodata, 1264K init, 240K bss, 9148K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:256
[    0.000000] Setting up vectored interrupts
[    0.000000] Setting up IPI vectored interrupts
[    0.000000] arch/mips/lantiq/xway/sysctrl.c:ltq_soc_init:517 LTQ_EBU_BUSCON2: 0x0001d3dd
[    0.000000] arch/mips/lantiq/xway/sysctrl.c:ltq_soc_init:520 LTQ_EBU_BUSCON2: 0x0001d3dd
[    0.000000] CPU Clock: 500MHz
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041786 ns
[    0.000012] sched_clock: 32 bits at 250MHz, resolution 4ns, wraps every 8589934590ns
[    0.007881] Calibrating delay loop... 332.54 BogoMIPS (lpj=665088)
[    0.042390] pid_max: default: 32768 minimum: 301
[    0.047260] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.053802] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.064188] Brought up 1 CPUs
[    0.072868] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.082538] futex hash table entries: 512 (order: 2, 16384 bytes)
[    0.088756] pinctrl core: initialized pinctrl subsystem
[    0.094695] NET: Registered protocol family 16
[    0.104609] pinctrl-xway 1e100b10.pinmux: Init done
[    0.110181] dma-xway 1e104100.dma: Init done - hw rev: 7, ports: 7, channels: 28
[    0.221318] dcdc-xrx200 1f106a00.dcdc: Core Voltage : 1016 mV
[    0.265862] gpio-stp-xway 1e100bb0.stp: Init done
[    0.271197] SCSI subsystem initialized
[    0.275383] usbcore: registered new interface driver usbfs
[    0.280911] usbcore: registered new interface driver hub
[    0.286264] usbcore: registered new device driver usb
[    0.298276] clocksource: Switched to clocksource MIPS
[    0.304769] NET: Registered protocol family 2
[    0.310084] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.317001] TCP bind hash table entries: 1024 (order: 1, 8192 bytes)
[    0.323381] TCP: Hash tables configured (established 1024 bind 1024)
[    0.329889] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.335736] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.342322] NET: Registered protocol family 1
[    0.350064] gptu: totally 6 16-bit timers/counters
[    0.354990] gptu: misc_register on minor 63
[    0.359137] gptu: succeeded to request irq 126
[    0.363629] gptu: succeeded to request irq 127
[    0.368141] gptu: succeeded to request irq 128
[    0.372652] gptu: succeeded to request irq 129
[    0.377167] gptu: succeeded to request irq 130
[    0.381679] gptu: succeeded to request irq 131
[    0.389282] lantiq,vmmc 1f103000.vmmc: requested GPIO 499
[    0.394581] lantiq,vmmc 1f103000.vmmc: reserved 1MB at 0x07300000
[    0.401087] phy-xrx200 gphy-xrx200: requesting lantiq/vr9_phy11g_a2x.bin
[    0.408407] phy-xrx200 gphy-xrx200: booting GPHY0 firmware at 72E0000
[    0.414755] phy-xrx200 gphy-xrx200: booting GPHY1 firmware at 72E0000
[    0.522479] genirq: Flags mismatch irq 0. 00000000 (RTLX) vs. 00000400 (IPI_resched)
[    0.531596] Crashlog allocated RAM at address 0x3f00000
[    0.542689] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[    0.560633] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.566378] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.595082] io scheduler noop registered
[    0.598984] io scheduler deadline registered (default)
[    0.604819] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112, base_baud = 0) is a lantiq,asc
[    0.613749] console [ttyLTQ0] enabled
[    0.613749] console [ttyLTQ0] enabled
[    0.621060] bootconsole [early0] disabled
[    0.621060] bootconsole [early0] disabled
[    0.630586] gen_nand 14000000.nand-parts: platform_nand_data is missing
[    0.635849] gen_nand: probe of 14000000.nand-parts failed with error -22
[    0.642798] nand: device found, Manufacturer ID: 0xec, Chip ID: 0xdc
[    0.648804] nand: Samsung NAND 512MiB 3,3V 8-bit
[    0.653420] nand: 512 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    0.664332] Bad block table found at page 262080, version 0x01
[    0.669707] Bad block table found at page 262016, version 0x01
[    0.675057] nand_read_bbt: bad block at 0x0000050e0000
[    0.680097] 16 ofpart partitions found on MTD device 14000000.nand-parts
[    0.686449] Creating 16 MTD partitions on "14000000.nand-parts":
[    0.692430] 0x000000000000-0x000000040000 : "uboot"
[    0.699299] 0x000000040000-0x000003c40000 : "rootfs"
[    0.706253] mtd: device 1 (rootfs) set to be root filesystem
[    0.711237] mtdsplit: no squashfs found in "rootfs"
[    0.715510] 0x000003c40000-0x000004140000 : "kernel"
[    0.722445] 0x000004140000-0x000004240000 : "tmp1"
[    0.728290] 0x000004240000-0x000004440000 : "tmp2"
[    0.734375] 0x000004440000-0x000004540000 : "sysconfig"
[    0.740565] 0x000004540000-0x000004640000 : "ubootconfig"
[    0.747012] 0x000004640000-0x000004700000 : "fwdiag"
[    0.753254] 0x000004700000-0x000004a00000 : "lcdimage"
[    0.759438] 0x000004a00000-0x000004b00000 : "mfgconfig"
[    0.766082] 0x000004b00000-0x000004c00000 : "sipdata"
[    0.772249] 0x000004c00000-0x000008c00000 : "voice"
[    0.778994] 0x000008c00000-0x00001be00000 : "ubi"
[    0.788295] 0x00001be00000-0x00001fa00000 : "rootfs2"
[    0.795252] 0x00001fa00000-0x00001ff00000 : "kernel2"
[    0.801676] 0x00001ff00000-0x000020000000 : "mystery"
[    0.810211] libphy: Fixed MDIO Bus: probed
[    0.914885] libphy: lantiq,xrx200-mdio: probed
[    0.926158] Static link. Port <0>!
[    0.929151] Registered fixed-link
[    0.931500] lantiq,xrx200-net 1e108000.eth eth0 (uninitialized): Connect as fixed link.
[    0.939575] Generic PHY fixed-0:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=fixed-0:00, irq=-1)
[    0.949278] lantiq,xrx200-net 1e108000.eth eth0 (uninitialized): Connect as common phy link.
[    1.029499] Intel XWAY PHY11G (xRX integrated) 0:13: attached PHY driver [Intel XWAY PHY11G (xRX integrated)] (mii_bus:phy_addr=0:13, irq=-1)
[    1.042609] dwc2 1e101000.ifxhcd: requested GPIO 495
[    1.096898] random: fast init done
[    1.147318] dwc2 1e101000.ifxhcd: DWC OTG Controller
[    1.150949] dwc2 1e101000.ifxhcd: new USB bus registered, assigned bus number 1
[    1.158252] dwc2 1e101000.ifxhcd: irq 62, io mem 0x00000000
[    1.163777] dwc2 1e101000.ifxhcd: Hardware does not support descriptor DMA mode -
[    1.171195] dwc2 1e101000.ifxhcd: falling back to buffer DMA mode.
[    1.179067] hub 1-0:1.0: USB hub found
[    1.181975] hub 1-0:1.0: 1 port detected
[    1.287125] dwc2 1e106000.ifxhcd: DWC OTG Controller
[    1.290773] dwc2 1e106000.ifxhcd: new USB bus registered, assigned bus number 2
[    1.298059] dwc2 1e106000.ifxhcd: irq 91, io mem 0x00000000
[    1.303579] dwc2 1e106000.ifxhcd: Hardware does not support descriptor DMA mode -
[    1.310999] dwc2 1e106000.ifxhcd: falling back to buffer DMA mode.
[    1.318668] hub 2-0:1.0: USB hub found
[    1.321512] hub 2-0:1.0: 1 port detected
[    1.326007] usbcore: registered new interface driver usb-storage
[    1.431760] ltq-cputemp cputemp@0: Current CPU die temperature: 45.5 °C
[    1.437353] wdt 1f8803f0.watchdog: Init done
[    1.443630] NET: Registered protocol family 10
[    1.451839] NET: Registered protocol family 17
[    1.455049] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    1.467868] 8021q: 802.1Q VLAN Support v1.8
[    1.475505] rtl8367b rtl8367b: using bus lantiq,xrx200-mdio
[    1.479996] rtl8367b rtl8367b: RTL8367RB chip found
[    1.968951] lantiq,xrx200-net 1e108000.eth eth0: port 2 got link
[    2.836588] ubi0: attaching mtd12
[    3.178359] ubi0: scanning is finished
[    3.197652] ubi0: attached mtd12 (name "ubi", size 306 MiB)
[    3.201877] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    3.208702] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 512
[    3.215396] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[    3.222358] ubi0: good PEBs: 2448, bad PEBs: 0, corrupted PEBs: 0
[    3.228450] ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
[    3.235678] ubi0: max/mean erase counter: 9/4, WL threshold: 4096, image sequence number: 873398826
[    3.244728] ubi0: available PEBs: 0, total reserved PEBs: 2448, PEBs reserved for bad PEB handling: 80
[    3.254136] ubi0: background thread "ubi_bgt0d" started, PID 4[    3.261354] Waiting 7 sec before mounting root device...
[   10.559887] UBIFS (ubi0:0): recovery needed
[   10.624346] UBIFS (ubi0:0): recovery deferred
[   10.627460] UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "rootfs", R/O mode
[   10.635583] UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[   10.645486] UBIFS (ubi0:0): FS size: 258523136 bytes (246 MiB, 2036 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
[   10.656183] UBIFS (ubi0:0): reserved for root: 0 bytes (0 KiB)
[   10.662023] UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID 14D3C3E6-5CC7-4D5F-9299-8B15B38F1707, small LPT model
[   10.674076] VFS: Mounted root (ubifs filesystem) readonly on device 0:10.
[   10.684011] Freeing unused kernel memory: 1264K
[   10.687138] This architecture does not have kernel memory protection.
[   10.799200] init: Console is alive
[   10.801648] init: - watchdog -
[   11.144747] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[   11.232767] JFS: nTxBlock = 866, nTxLock = 6931
[   11.251839] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   11.259137] ehci-platform: EHCI generic platform driver
[   11.272201] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[   11.278541] ohci-platform: OHCI generic platform driver
[   11.284382] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[   11.295188] init: - preinit -
## Error: "bootnum" not defined
Bootnum: 
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[   14.812176] mount_root: mounting /dev/root
[   14.816094] UBIFS (ubi0:0): completing deferred recovery
[   14.854554] UBIFS (ubi0:0): deferred recovery completed
[   14.859848] UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 530
[   14.867260] mount_root: loading kmods from internal overlay
[   14.939412] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[   14.950081] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[   16.165747] block: attempting to load /etc/config/fstab
[   16.173787] block: extroot: not configured
[   16.181174] urandom-seed: Seeding with /etc/urandom.seed
[   16.234046] procd: - early -
[   16.236754] procd: - watchdog -
[   16.753048] lantiq,xrx200-net 1e108000.eth eth0: port 2 lost link
[   16.880700] procd: - watchdog -
[   16.883141] procd: - ubus -
[   16.950269] procd: - init -
Please press Enter to activate this console.
[   17.664381] kmodloader: loading kernel modules from /etc/modules.d/*
[   17.699924] fbtft_of_value: buswidth = 8
[   17.702564] fbtft_of_value: debug = 1
[   17.706106] fbtft_of_value: rotate = 270
[   17.710001] fbtft_of_value: fps = 30
[   17.715169] fb_ili9341_eb904 easybox904-display: fbtft_request_one_gpio: 'reset-gpios' = GPIO468
[   17.722702] fb_ili9341_eb904 easybox904-display: fbtft_request_one_gpio: 'led-gpios' = GPIO490
[   17.851692] ili9341_Probe: Probed ID4: 9341
[   18.016787] graphics fb0: fb_ili9341_eb904 frame buffer, 320x240, 150 KiB video memory, 16 KiB DMA buffer memory, fps=31
[   18.036541] IFXOS, Version 1.5.19 (c) Copyright 2009, Lantiq Deutschland GmbH
[   18.057430] NET: Registered protocol family 8
[   18.060349] NET: Registered protocol family 20
[   18.128148] RPC: Registered named UNIX socket transport module.
[   18.132748] RPC: Registered udp transport module.
[   18.137379] RPC: Registered tcp transport module.
[   18.142064] RPC: Registered tcp NFSv4.1 backchannel transport module.
[   18.171393] tun: Universal TUN/TAP device driver, 1.6
[   18.175118] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[   18.259413] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[   18.275787] PPP generic driver version 2.4.2
[   18.290463] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   18.307454] Netfilter messages via NETLINK v0.30.
[   18.317826] ip_set: protocol 6
[   18.446428] Lantiq (VRX) DSL CPE MEI driver, version 1.5.17.6, (c) 2007-2015 Lantiq Beteiligungs-GmbH & Co. KG[   18.469717] i2c /dev entries driver
[   18.516516] 
[   18.516516] 
[   18.516516] Lantiq CPE API Driver version: DSL CPE API V4.17.18.6
[   18.524228] 
[   18.524228] Predefined debug level: 3
[   18.535919] i2c-gpio i2c: using pins 481 (SDA) and 476 (SCL)
[   21.118257] input: eb904_keypad as /devices/platform/i2c/i2c-0/0-0014/input/input0
[   21.153681] hidraw: raw HID events driver (C) Jiri Kosina
[   21.170482] Bridge firewalling registered
[   21.175215] Loading modules backported from Linux version wt-2017-10-06-0-ga7a22fbbd1f0
[   21.181898] Backport generated by backports.git v4.14-rc2-1-6-gedfb595c
[   21.210138] Ebtables v2.0 registered
[   21.218590] ip_tables: (C) 2000-2006 Netfilter Core Team
[   21.232685] Infineon Technologies DEU driver version 2.0.0 
[   21.238945] IFX DEU DES initialized (multiblock).
[   21.243548] IFX DEU AES initialized (multiblock).
[   21.247600] IFX DEU ARC4 initialized (multiblock).
[   21.252145] IFX DEU SHA1 initialized.
[   21.255738] IFX DEU MD5 initialized.
[   21.259257] IFX DEU SHA1_HMAC initialized.
[   21.263381] IFX DEU MD5_HMAC initialized.
[   21.294454] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
[   21.306470] ctnetlink v0.93: registering with nfnetlink.
[   21.391956] NET: Registered protocol family 24
[   21.397275] usbcore: registered new interface driver ums-alauda
[   21.403960] usbcore: registered new interface driver ums-cypress
[   21.410851] usbcore: registered new interface driver ums-datafab
[   21.417681] usbcore: registered new interface driver ums-freecom
[   21.424548] usbcore: registered new interface driver ums-isd200
[   21.431382] usbcore: registered new interface driver ums-jumpshot
[   21.438464] usbcore: registered new interface driver ums-karma
[   21.445422] usbcore: registered new interface driver ums-sddr09
[   21.452101] usbcore: registered new interface driver ums-sddr55
[   21.458999] usbcore: registered new interface driver ums-usbat
[   21.496407] xt_time: kernel timezone is -0000
[   21.502262] usbcore: registered new interface driver cdc_ether
[   21.757424] usbcore: registered new interface driver rndis_host
[   21.817538] usbcore: registered new interface driver rt2800usb
[   21.823119] kmodloader: done loading kernel modules from /etc/modules.d/*
[   34.614658] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   34.619230] lantiq,xrx200-net 1e108000.eth eth0: port 2 got link
[   34.629112] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   34.646413] br-lan: port 1(eth0.66) entered blocking state
[   34.650584] br-lan: port 1(eth0.66) entered disabled state
[   34.656760] device eth0.66 entered promiscuous mode
[   34.660898] device eth0 entered promiscuous mode
[   34.699850] br-lan: port 1(eth0.66) entered blocking state
[   34.703979] br-lan: port 1(eth0.66) entered forwarding state
[   45.451255] Warnning!! syncmiimac is foreced to 0 in dual concurrent mode.
[   45.456824] RT3883iNIC: 802.11n WLAN MII driver v2.4.0.6 (Feb. 09, 2011)
[   45.463603] eth0.3: Master at 0x0, 00:11:22:33:44:55
[   45.468479] Use default profile path.
[   45.472069] -----> mii_hardware_reset
[   45.485775] -----> mii_hardware_reset
[   45.488006] ===> Get MAC from iNIC
[   45.491433] ============= Init Thread ===================
[   45.498484] RacfgTaskThread pid = 1451
[   45.501276] RacfgBacklogThread pid = 1452
[   45.506399] wl000: Ralink iNIC at 0x0, 00:43:0c:00:00:00
[   45.515916] Ignored command_type: 1, command_id: 1 
[   45.524150] ===> Get MAC from iNIC
[   45.526142] ============= Init Thread ===================
[   45.565105] RacfgTaskThread pid = 1457
[   45.573424] RacfgBacklogThread pid = 1462
[   45.577677] wl010: Ralink iNIC at 0x0, 00:43:0c:00:00:00
[   45.618305] iNIC Open wl000
[   45.619663] -----> mii_hardware_reset
[   46.640916] -----> mii_hardware_reset
[   46.643141] Op mode = 1
[   46.645650] ConcurrentObj.CardCount=0
[   46.649274] Read profile[0]
[   46.654502] BssidNum=2
[   46.657127] Read profile[1]
[   46.659848] BssidNum=2
[   46.662535] rlk_inic_mbss_init (pAd->RaCfgObj.BssidNum=2)
[   46.666570] rlk_inic_mbss_init --->
[   46.670077] Register MBSSID IF (wl001)
[   46.675258] register_netdev done
[   46.677130] rlk_inic_mbss_init <---
[   46.680520] ConcurrentObj.CardCount=0 init_flag=0
[   46.685258] Wait for boot done...
[   46.688513] Call RaCfgWaitSyncRsp
[   46.692639] RACFG_CMD_BOOT_NOTIFY
[   46.697394] Firmware path iNIC/RT3883/iNIC_ap.bin
[   46.700670] Profile[0] path iNIC/RT3883/iNIC_ap.dat, read path iNIC/RT3883/iNIC_ap.dat
[   46.708654] EEPROM[0] path iNIC/RT3883/iNIC_e2p.bin, read path iNIC/RT3883/iNIC_e2p.bin
[   46.716625] Profile[1] path iNIC/RT3883/iNIC_ap1.dat, read path iNIC/RT3883/iNIC_ap1.dat
[   46.724718] EEPROM[1] path iNIC/RT3883/iNIC_e2p1.bin, read path iNIC/RT3883/iNIC_e2p1.bin
[   46.732902] Request file: iNIC/RT3883/iNIC_ap.bin
[   46.934061] Request file: iNIC/RT3883/iNIC_ap.dat
[   46.937769] Request file: iNIC/RT3883/iNIC_e2p.bin
[   46.943257] Request file: iNIC/RT3883/iNIC_ap1.dat
[   46.947548] Request file: iNIC/RT3883/iNIC_e2p1.bin
[   46.952856] Upload Profile 1024 bytes from file, 0 from extra...
[   47.671816] RACFG_CMD_BOOT_INITCFG(0)
[   47.674261] Upload Profile 1024 bytes from file, 0 from extra...
[   47.680550] RACFG_CMD_BOOT_INITCFG(1)
[   47.684079] Upload Profile 1024 bytes from file, 0 from extra...
[   47.690225] RACFG_CMD_BOOT_INITCFG(2)
[   47.693743] Upload Profile 1024 bytes from file, 0 from extra...
[   47.699882] RACFG_CMD_BOOT_INITCFG(3)
[   47.703401] Upload Profile 1024 bytes from file, 39 from extra...
[   47.709621] RACFG_CMD_BOOT_INITCFG(4)
[   47.712996] Upload Profile 472 bytes from file, 0 from extra...
[   47.718980] RACFG_CMD_BOOT_INITCFG(5)
[   47.722800] Upload Profile 0 bytes from file, 0 from extra...
[   47.728182] Send Init Cfg Data Done(6 packets)
[   47.733054] RACFG_CMD_BOOT_UPLOAD(0)
[   47.736791] RACFG_CMD_BOOT_UPLOAD(1)
[   47.740503] RACFG_CMD_BOOT_UPLOAD(2)
[   47.969532] random: crng init done
[   48.032190] net wl000: CRC: 01 08 14 18 07 3a 97 85 22 32 2e 35 2e 31 2e 33 22 00 00 00 32 30 31 34 31 32 31 32 00 00 00 00 00 00 00 00 58 cb 08 00
[   48.044524] Send RT3883iNIC Firmware Done
[   48.048072] ===================================
[   48.052566] version: "2.5.1.3"
[   48.055603] size:    576344 bytes
[   48.058906] date:    20141212
[   48.061866] ===================================
[   48.061866] 
[   48.067865] Send STARTUP to RT3883iNIC
[   48.071680] Close Firmware file
[   48.071714] RACFG_CMD_BOOT_STARTUP
[   55.868989] RACFG_CMD_GET_MAC, len: 35 
[   55.871385] Get concurrent card MAC address:00:0c:43:43:60:5500:0c:43:53:92:00
[   55.878707] Update MAC(0)=00:0c:43:43:60:55
[   55.882838] Update MAC(1)=02:0c:43:43:60:55
[   55.887012] Update MAC(0)=00:0c:43:53:92:00
[   55.891174] Warning! MAC addr not equal to MII master => [   55.896401] set MiiMasterMac=00:11:22:33:44:55
[   55.900824] [syncmiimac] disabled?
[   55.904233] OK! Got target's MAC address, boot done.
[   55.917092] iNIC Open wl010
[   55.918445] Op mode = 1
[   55.921172] ConcurrentObj.CardCount=1
[   55.924513] rlk_inic_mbss_init (pAd->RaCfgObj.BssidNum=2)
[   55.930001] rlk_inic_mbss_init --->
[   55.933500] Register MBSSID IF (wl011)
[   55.938659] register_netdev done
[   55.940439] rlk_inic_mbss_init <---
[   55.944001] ConcurrentObj.CardCount=1 init_flag=1
[   66.002345] svc: failed to register lockdv1 RPC service (errno 124).

43 Odpowiedź przez verdis

  • verdis
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2017-10-21
  • Posty: 13

Odp: Easybox 904xDSL

Uruchomiłem WAN na DSL oraz wifi wg powyższej instrukcji. Wszystko działa jeśli chodzi o AP bez problemu jedynie w GUI są niepoprawne informacje dotyczące wifi ale to szczegół.
Jeszcze raz wielkie dzięki.
Chciałbym uruchomić obsługę USB i udostępniać pliki z dysku- co trzeba doinstalować ?

44 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 106,450

Odp: Easybox 904xDSL

http://eko.one.pl/?p=openwrt-hdd#barrie … szewydania

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

45 Odpowiedź przez verdis

  • verdis
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2017-10-21
  • Posty: 13

Odp: Easybox 904xDSL

Cezary dzięki po raz kolejny.
Mam taki problem, nie mogę pobrać listy pakietów przez GUI - czy to normalne.
Poniżej komunikat z LEDE:


Downloading http://downloads.lede-project.org/snaps … ackages.gz
Updated list of available packages in /var/opkg-lists/reboot_core
Downloading http://downloads.lede-project.org/snaps … ckages.sig
Signature check passed.
Downloading http://downloads.lede-project.org/snaps … ackages.gz
Updated list of available packages in /var/opkg-lists/reboot_base
Downloading http://downloads.lede-project.org/snaps … ckages.sig
Signature check passed.
Downloading http://downloads.lede-project.org/snaps … ackages.gz
*** Failed to download the package list from http://downloads.lede-project.org/snaps … ackages.gz

Collected errors:
* opkg_download: Failed to download http://downloads.lede-project.org/snaps … ckages.gz, wget returned 8.

Czy można jakoś pobrać te pakiety ?

46 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 106,450

Odp: Easybox 904xDSL

Normalnie, bo takie repo prostu nigdy nie istniało i nie istnieje. Wywal to repo z konfiga, niepotrzebne jest dodane.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

47 Odpowiedź przez verdis

  • verdis
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2017-10-21
  • Posty: 13

Odp: Easybox 904xDSL

Nie mam pojęcia jak to zrobić.
Tzn. z folderu config ?

48 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 106,450

Odp: Easybox 904xDSL

Z /etc/opkg/distfeeds.cong wywal

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

49 Odpowiedź przez verdis

  • verdis
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2017-10-21
  • Posty: 13

Odp: Easybox 904xDSL

Usunąłem plik config ale nadal nie idzie, tym razem wcale nie aktualizuje pakietów.
Coś robię nie tak chyba.

root@LEDE:~# opkg update
root@LEDE:~# opkg install kmod-usb-core kmod-usb2 kmod-usb-storage
Package kmod-usb-core (4.9.54-1) installed in root is up to date.
Unknown package 'kmod-usb2'.
Unknown package 'kmod-usb-storage'.
Collected errors:
* opkg_install_cmd: Cannot install package kmod-usb2.
* opkg_install_cmd: Cannot install package kmod-usb-storage.

50 Odpowiedź przez verdis

  • verdis
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2017-10-21
  • Posty: 13

Odp: Easybox 904xDSL

Jak stworzyć nowe repozytorium bo chyba inaczej nie ruszę.