Odp: NEXX WT3020H
I okazało się że 16 jest więcej niż się przyznaliście ![]()
Nie jesteś zalogowany. Proszę się zalogować lub zarejestrować.
eko.one.pl → Oprogramowanie / Software → NEXX WT3020H
Strony Poprzednia 1 … 14 15 16 17 18 … 21 Następna
Zaloguj się lub zarejestruj by napisać odpowiedź
I okazało się że 16 jest więcej niż się przyznaliście ![]()
![]()
Bo dopiero od wczoraj
I okazało się że 16 jest więcej niż się przyznaliście
No właśnie byłem zdziwiony, bo mój w statystykach pojawił się jako pierwszy.
Wracając do tematu upgrade CC do LEDE. Sprawdziłem temat jeszcze raz i efekt jest taki, że dioda nie miga przy uruchamianiu i nie ma dostępu do sieci. Poniżej log:
root@OpenWrt:/tmp# sysupgrade -n luci-17.01-snapshot-r3371-79cd141-ramips-mt7620
-wt3020-16M-squashfs-sysupgrade.bin
killall: watchdog: no process killed
Sending TERM to remaining processes ... logd rpcd odhcpd uhttpd dnsmasq smbd nmb d ntpd netifd odhcp6c ubusd
Sending KILL to remaining processes ...
Switching to ramdisk...
Performing system upgrade...
Unlocking firmware ...
Writing from <stdin> to firmware ...
Upgrade completed
Rebooting s[ 582.560000] reboot: Restarting system
ystem...
U-Boot 1.1.3 (Jan 3 2014 - 09:12:42)
MAX Board: Ralink APSoC DRAM: 64 MB
relocate_code Pointer at: 83fb4000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
******************************
Software System Reset Occurred
******************************
spi_wait_nsec: 29
spi device id: ef 40 18 0 0 (40180000)
Warning: un-recognized chip ID, please update bootloader!
raspi_read: from:30000 len:1000
raspi_read: from:30000 len:1000
============================================
Ralink UBoot Version: 4.1.1.0
--------------------------------------------
ASIC 7620_MP (Port5<->None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Jan 3 2014 Time:09:12:42
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768
##### The CPU freq = 580 MHZ ####
estimate memory size =64 Mbytes
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP. 0
3: System Boot system code via Flash.
## Booting image at bc050000 ...
raspi_read: from:50000 len:40
Image Name: MIPS LEDE Linux-4.4.61
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1312277 Bytes = 1.3 MB
Load Address: 80000000
Entry Point: 80000000
raspi_read: from:50040 len:140615
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 64
Starting kernel ...
[ 0.000000] Linux version 4.4.61 (cezary@eko.one.pl) (gcc version 5.4.0 (LEDE GCC 5.4.0 r3103-1b51a49) ) #0 Wed May 3 23:03:25 2017
[ 0.000000] Board has DDR1
[ 0.000000] Analog PMU set to hw control
[ 0.000000] Digital PMU set to hw control
[ 0.000000] SoC Type: MediaTek MT7620N ver:2 eco:6
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
[ 0.000000] MIPS: machine is Nexx WT3020 (16M)
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=0005fe70
[ 0.000000] Readback ErrCtl register=0005fe70
[ 0.000000] Memory: 60580K/65536K available (3037K kernel code, 142K rwdata, 720K rodata, 188K init, 208K bss, 4956K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:256
[ 0.000000] CPU Clock: 580MHz
[ 0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns
[ 0.000000] systick: enable autosleep mode
[ 0.000000] systick: running - mult: 214748, shift: 32
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns
[ 0.000012] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405115902ns
[ 0.015455] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[ 0.080605] pid_max: default: 32768 minimum: 301
[ 0.089916] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.102937] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.122097] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.141586] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.153831] pinctrl core: initialized pinctrl subsystem
[ 0.165369] NET: Registered protocol family 16
[ 0.192777] rt2880_gpio 10000600.gpio: registering 24 gpios
[ 0.203792] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[ 0.216208] rt2880_gpio 10000660.gpio: registering 32 gpios
[ 0.227198] rt2880_gpio 10000660.gpio: registering 32 irq handlers
[ 0.239602] rt2880_gpio 10000688.gpio: registering 1 gpios
[ 0.250401] rt2880_gpio 10000688.gpio: registering 1 irq handlers
[ 0.264091] clocksource: Switched to clocksource systick
[ 0.276017] NET: Registered protocol family 2
[ 0.285587] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.299354] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.311948] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.324674] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.336205] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.348936] NET: Registered protocol family 1
[ 0.361649] rt-timer 10000100.timer: maximum frequency is 1220Hz
[ 0.374594] Crashlog allocated RAM at address 0x3f00000
[ 0.401319] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.412841] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.435032] io scheduler noop registered
[ 0.442685] io scheduler deadline registered (default)
[ 0.453200] ralink-usb-phy usbphy: invalid resource
[ 0.463425] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.479464] console [ttyS0] disabled
[ 0.486502] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
[ 0.506178] console [ttyS0] enabled
[ 0.506178] console [ttyS0] enabled
[ 0.520000] bootconsole [early0] disabled
[ 0.520000] bootconsole [early0] disabled
[ 0.542714] spi spi0.0: force spi mode3
[ 0.550940] m25p80 spi0.0: w25q128 (16384 Kbytes)
[ 0.560379] 4 ofpart partitions found on MTD device spi0.0
[ 0.571308] Creating 4 MTD partitions on "spi0.0":
[ 0.580858] 0x000000000000-0x000000030000 : "u-boot"
[ 0.592502] 0x000000030000-0x000000040000 : "u-boot-env"
[ 0.605027] 0x000000040000-0x000000050000 : "factory"
[ 0.616952] 0x000000050000-0x000001000000 : "firmware"
[ 1.950249] 2 uimage-fw partitions found on MTD device firmware
[ 1.962078] 0x000000050000-0x000000190655 : "kernel"
[ 1.973574] 0x000000190655-0x000001000000 : "rootfs"
[ 1.985311] mtd: device 5 (rootfs) set to be root filesystem
[ 1.996787] 1 squashfs-split partitions found on MTD device rootfs
[ 2.009120] 0x00000065f000-0x000001000000 : "rootfs_data"
[ 2.024794] mtk_soc_eth 10100000.ethernet: loaded mt7620 driver
[ 2.037383] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
[ 2.054445] rt2880_wdt 10000120.watchdog: Initialized
[ 2.066048] NET: Registered protocol family 10
[ 2.079397] NET: Registered protocol family 17
[ 2.088417] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 2.113577] 8021q: 802.1Q VLAN Support v1.8
[ 2.136187] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[ 2.151295] Freeing unused kernel memory: 188K (803d1000 - 80400000)
[ 4.567081] init: Console is alive
[ 4.574060] init: - watchdog -
[ 7.657889] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 7.796315] usbcore: registered new interface driver usbfs
[ 7.807421] usbcore: registered new interface driver hub
[ 7.818132] usbcore: registered new device driver usb
[ 7.867418] SCSI subsystem initialized
[ 7.881798] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 7.896591] ehci-platform: EHCI generic platform driver
[ 7.917359] phy phy-usbphy.0: remote usb device wakeup disabled
[ 7.929162] phy phy-usbphy.0: UTMI 16bit 30MHz
[ 7.938040] ehci-platform 101c0000.ehci: EHCI Host Controller
[ 7.949525] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
[ 7.965426] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
[ 7.983507] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
[ 7.997073] hub 1-0:1.0: USB hub found
[ 8.004967] hub 1-0:1.0: 1 port detected
[ 8.016199] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 8.030212] ohci-platform: OHCI generic platform driver
[ 8.040950] ohci-platform 101c1000.ohci: Generic Platform OHCI controller
[ 8.054554] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
[ 8.070413] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
[ 8.105114] hub 2-0:1.0: USB hub found
[ 8.113033] hub 2-0:1.0: 1 port detected
[ 8.127881] usbcore: registered new interface driver usb-storage
[ 8.140882] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 8.159339] init: - preinit -
[ 9.672162] 8021q: adding VLAN 0 to HW filter on device eth0
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 10.979166] mount_root: loading kmods from internal overlay
[ 11.028590] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[ 11.044096] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[ 11.701920] block: attempting to load /etc/config/fstab
[ 11.714550] block: unable to load configuration (fstab: Entry not found)
[ 11.728061] block: no usable configuration
[ 11.736968] mount_root: jffs2 not ready yet, using temporary tmpfs overlay
[ 11.757253] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 11.894468] procd: - early -
[ 11.900448] procd: - watchdog -
[ 12.762541] procd: - ubus -
[ 12.868758] random: jshn: uninitialized urandom read (4 bytes read, 24 bits of entropy available)
[ 13.084203] random: ubusd: uninitialized urandom read (4 bytes read, 24 bits of entropy available)
[ 13.102721] random: ubusd: uninitialized urandom read (4 bytes read, 24 bits of entropy available)
[ 13.120943] random: ubus: uninitialized urandom read (4 bytes read, 24 bits of entropy available)
[ 13.138884] random: ubusd: uninitialized urandom read (4 bytes read, 24 bits of entropy available)
[ 13.157206] random: ubusd: uninitialized urandom read (4 bytes read, 24 bits of entropy available)
[ 13.179039] random: ubusd: uninitialized urandom read (4 bytes read, 24 bits of entropy available)
[ 13.197068] random: ubusd: uninitialized urandom read (4 bytes read, 24 bits of entropy available)
[ 13.215158] random: ubusd: uninitialized urandom read (4 bytes read, 24 bits of entropy available)
[ 13.233272] random: ubusd: uninitialized urandom read (4 bytes read, 24 bits of entropy available)
[ 13.251580] procd: - init -
Please press Enter to activate this console.
[ 14.448286] kmodloader: loading kernel modules from /etc/modules.d/*
[ 14.743497] tun: Universal TUN/TAP device driver, 1.6
[ 14.753632] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 14.811314] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 14.842766] Loading modules backported from Linux version wt-2017-01-31-0-ge882dff19e7f
[ 14.858782] Backport generated by backports.git backports-20160324-13-g24da7d3c
[ 15.040896] u32 classifier
[ 15.046288] input device check on
[ 15.053629] Actions configured
[ 15.089756] Mirror/redirect action on
[ 15.113008] nf_conntrack version 0.5.0 (949 buckets, 3796 max)
[ 15.154703] fuse init (API version 7.23)
[ 15.186549] usbcore: registered new interface driver cdc_acm
[ 15.197893] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 15.249243] usbcore: registered new interface driver cdc_wdm
[ 15.284215] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 15.423462] usbcore: registered new interface driver usblp
[ 15.469394] usbcore: registered new interface driver usbserial
[ 15.481203] usbcore: registered new interface driver usbserial_generic
[ 15.494354] usbserial: USB Serial support registered for generic
[ 15.620728] xt_time: kernel timezone is -0000
[ 15.640074] usbcore: registered new interface driver cdc_ether
[ 15.672740] usbcore: registered new interface driver cdc_ncm
[ 15.701130] usbcore: registered new interface driver huawei_cdc_ncm
[ 15.769896] PPP generic driver version 2.4.2
[ 15.801137] NET: Registered protocol family 24
[ 15.822294] usbcore: registered new interface driver qmi_wwan
[ 15.842765] usbcore: registered new interface driver rndis_host
[ 15.911892] rt2800_wmac 10180000.wmac: loaded eeprom from mtd device "factory"
[ 15.926367] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 6352, rev 0500 detected
[ 15.941818] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 7620 detected
[ 16.012450] usbcore: registered new interface driver sierra
[ 16.023739] usbserial: USB Serial support registered for Sierra USB modem
[ 16.072312] usbcore: registered new interface driver sierra_net
[ 16.102139] usbcore: registered new interface driver cdc_mbim
[ 16.133728] usbcore: registered new interface driver option
[ 16.145017] usbserial: USB Serial support registered for GSM modem (1-port)
[ 16.196246] usbcore: registered new interface driver qcserial
[ 16.207910] usbserial: USB Serial support registered for Qualcomm USB modem
[ 16.301822] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 30.442304] 8021q: adding VLAN 0 to HW filter on device eth0
[ 30.494196] device eth0.1 entered promiscuous mode
[ 30.503820] device eth0 entered promiscuous mode
[ 30.573433] br-lan: port 1(eth0.1) entered forwarding state
[ 30.584635] br-lan: port 1(eth0.1) entered forwarding state
[ 32.579673] br-lan: port 1(eth0.1) entered forwarding state
[ 54.502174] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[ 54.516788] jffs2_build_filesystem(): unlocking the mtd device... done.
[ 54.530003] jffs2_build_filesystem(): erasing all blocks after the end marker...
[ 76.599663] random: nonblocking pool is initialized
[ 155.085229] br-lan: port 1(eth0.1) entered disabled state
[ 156.863252] br-lan: port 1(eth0.1) entered forwarding state
[ 156.874428] br-lan: port 1(eth0.1) entered forwarding state
[ 158.869623] br-lan: port 1(eth0.1) entered forwarding state
[ 214.333871] br-lan: port 1(eth0.1) entered disabled state
[ 217.189141] br-lan: port 1(eth0.1) entered forwarding state
[ 217.200321] br-lan: port 1(eth0.1) entered forwarding state
[ 219.199625] br-lan: port 1(eth0.1) entered forwarding state
[ 279.160089] br-lan: port 1(eth0.1) entered disabled state
[ 295.751783] done.
[ 295.755661] jffs2: notice: (1736) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 304.989926] br-lan: port 1(eth0.1) entered forwarding state
[ 305.001146] br-lan: port 1(eth0.1) entered forwarding state
[ 305.862509] br-lan: port 1(eth0.1) entered forwarding stateZwykłe uruchomienie, nic tu ciekawego nie ma.
No właśnie, ale sieć nie działa i dioda przy uruchamianiu nie miga.
Problemem może być to: https://github.com/lede-project/source/ … c97e53dd2f
Poczekaj do wieczora, zrobię obraz na nexxa i przetestujesz sobie.
Po restarcie sieci nadal brak.
U-Boot 1.1.3 (Jan 3 2014 - 09:12:42)
MAX Board: Ralink APSoC DRAM: 64 MB
relocate_code Pointer at: 83fb4000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
spi_wait_nsec: 29
spi device id: ef 40 18 0 0 (40180000)
Warning: un-recognized chip ID, please update bootloader!
raspi_read: from:30000 len:1000
raspi_read: from:30000 len:1000
============================================
Ralink UBoot Version: 4.1.1.0
--------------------------------------------
ASIC 7620_MP (Port5<->None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Jan 3 2014 Time:09:12:42
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768
##### The CPU freq = 580 MHZ ####
estimate memory size =64 Mbytes
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP. 0
3: System Boot system code via Flash.
## Booting image at bc050000 ...
raspi_read: from:50000 len:40
Image Name: MIPS LEDE Linux-4.4.61
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1312277 Bytes = 1.3 MB
Load Address: 80000000
Entry Point: 80000000
raspi_read: from:50040 len:140615
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 64
Starting kernel ...
[ 0.000000] Linux version 4.4.61 (cezary@eko.one.pl) (gcc version 5.4.0 (LEDE GCC 5.4.0 r3103-1b51a49) ) #0 Wed May 3 23:03:25 2017
[ 0.000000] Board has DDR1
[ 0.000000] Analog PMU set to hw control
[ 0.000000] Digital PMU set to hw control
[ 0.000000] SoC Type: MediaTek MT7620N ver:2 eco:6
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
[ 0.000000] MIPS: machine is Nexx WT3020 (16M)
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=0006e47d
[ 0.000000] Readback ErrCtl register=0006e47d
[ 0.000000] Memory: 60580K/65536K available (3037K kernel code, 142K rwdata, 720K rodata, 188K init, 208K bss, 4956K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:256
[ 0.000000] CPU Clock: 580MHz
[ 0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns
[ 0.000000] systick: enable autosleep mode
[ 0.000000] systick: running - mult: 214748, shift: 32
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns
[ 0.000012] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405115902ns
[ 0.015455] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[ 0.080594] pid_max: default: 32768 minimum: 301
[ 0.089906] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.102927] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.122086] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.141576] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.153820] pinctrl core: initialized pinctrl subsystem
[ 0.165358] NET: Registered protocol family 16
[ 0.192766] rt2880_gpio 10000600.gpio: registering 24 gpios
[ 0.203781] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[ 0.216197] rt2880_gpio 10000660.gpio: registering 32 gpios
[ 0.227187] rt2880_gpio 10000660.gpio: registering 32 irq handlers
[ 0.239592] rt2880_gpio 10000688.gpio: registering 1 gpios
[ 0.250390] rt2880_gpio 10000688.gpio: registering 1 irq handlers
[ 0.264081] clocksource: Switched to clocksource systick
[ 0.276006] NET: Registered protocol family 2
[ 0.285576] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.299343] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.311937] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.324663] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.336195] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.348926] NET: Registered protocol family 1
[ 0.361638] rt-timer 10000100.timer: maximum frequency is 1220Hz
[ 0.374583] Crashlog allocated RAM at address 0x3f00000
[ 0.401307] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.412829] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.435019] io scheduler noop registered
[ 0.442672] io scheduler deadline registered (default)
[ 0.453187] ralink-usb-phy usbphy: invalid resource
[ 0.463412] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.479451] console [ttyS0] disabled
[ 0.486489] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
[ 0.506165] console [ttyS0] enabled
[ 0.506165] console [ttyS0] enabled
[ 0.519987] bootconsole [early0] disabled
[ 0.519987] bootconsole [early0] disabled
[ 0.542702] spi spi0.0: force spi mode3
[ 0.550928] m25p80 spi0.0: w25q128 (16384 Kbytes)
[ 0.560367] 4 ofpart partitions found on MTD device spi0.0
[ 0.571297] Creating 4 MTD partitions on "spi0.0":
[ 0.580847] 0x000000000000-0x000000030000 : "u-boot"
[ 0.592490] 0x000000030000-0x000000040000 : "u-boot-env"
[ 0.605016] 0x000000040000-0x000000050000 : "factory"
[ 0.616940] 0x000000050000-0x000001000000 : "firmware"
[ 1.950247] 2 uimage-fw partitions found on MTD device firmware
[ 1.962078] 0x000000050000-0x000000190655 : "kernel"
[ 1.973574] 0x000000190655-0x000001000000 : "rootfs"
[ 1.985308] mtd: device 5 (rootfs) set to be root filesystem
[ 1.996785] 1 squashfs-split partitions found on MTD device rootfs
[ 2.009119] 0x00000065f000-0x000001000000 : "rootfs_data"
[ 2.024782] mtk_soc_eth 10100000.ethernet: loaded mt7620 driver
[ 2.037372] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
[ 2.054434] rt2880_wdt 10000120.watchdog: Initialized
[ 2.066036] NET: Registered protocol family 10
[ 2.079384] NET: Registered protocol family 17
[ 2.088403] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 2.113563] 8021q: 802.1Q VLAN Support v1.8
[ 2.136174] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[ 2.151282] Freeing unused kernel memory: 188K (803d1000 - 80400000)
[ 4.566752] init: Console is alive
[ 4.573730] init: - watchdog -
[ 7.657501] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 7.795234] usbcore: registered new interface driver usbfs
[ 7.806317] usbcore: registered new interface driver hub
[ 7.817028] usbcore: registered new device driver usb
[ 7.868320] SCSI subsystem initialized
[ 7.882723] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 7.897511] ehci-platform: EHCI generic platform driver
[ 7.918277] phy phy-usbphy.0: remote usb device wakeup disabled
[ 7.930080] phy phy-usbphy.0: UTMI 16bit 30MHz
[ 7.938959] ehci-platform 101c0000.ehci: EHCI Host Controller
[ 7.950444] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
[ 7.966344] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
[ 7.984113] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
[ 7.997676] hub 1-0:1.0: USB hub found
[ 8.005569] hub 1-0:1.0: 1 port detected
[ 8.016808] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 8.030825] ohci-platform: OHCI generic platform driver
[ 8.041563] ohci-platform 101c1000.ohci: Generic Platform OHCI controller
[ 8.055166] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
[ 8.071026] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
[ 8.105727] hub 2-0:1.0: USB hub found
[ 8.113646] hub 2-0:1.0: 1 port detected
[ 8.128487] usbcore: registered new interface driver usb-storage
[ 8.141500] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 8.159948] init: - preinit -
[ 9.672360] 8021q: adding VLAN 0 to HW filter on device eth0
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 10.639422] mount_root: loading kmods from internal overlay
[ 10.689313] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[ 10.704704] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[ 12.633497] jffs2: notice: (375) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 12.665188] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 12.687751] block: extroot: not configured
[ 13.977536] jffs2: notice: (372) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 14.655930] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 14.676770] block: extroot: not configured
[ 14.686093] mount_root: switching to jffs2 overlay
[ 14.711990] urandom-seed: Seeding with /etc/urandom.seed
[ 14.863915] procd: - early -
[ 14.870430] procd: - watchdog -
[ 15.683961] procd: - ubus -
[ 15.849699] random: jshn: uninitialized urandom read (4 bytes read, 28 bits of entropy available)
[ 16.068468] random: ubusd: uninitialized urandom read (4 bytes read, 28 bits of entropy available)
[ 16.086684] random: ubus: uninitialized urandom read (4 bytes read, 28 bits of entropy available)
[ 16.151673] random: ubusd: uninitialized urandom read (4 bytes read, 28 bits of entropy available)
[ 16.187036] random: ubusd: uninitialized urandom read (4 bytes read, 28 bits of entropy available)
[ 16.224857] random: ubusd: uninitialized urandom read (4 bytes read, 28 bits of entropy available)
[ 16.264112] random: ubusd: uninitialized urandom read (4 bytes read, 29 bits of entropy available)
[ 16.288776] random: jshn: uninitialized urandom read (4 bytes read, 29 bits of entropy available)
[ 16.306686] random: ubusd: uninitialized urandom read (4 bytes read, 29 bits of entropy available)
[ 16.333880] random: ubusd: uninitialized urandom read (4 bytes read, 29 bits of entropy available)
[ 16.352419] procd: - init -
Please press Enter to activate this console.
[ 17.442268] kmodloader: loading kernel modules from /etc/modules.d/*
[ 17.758778] tun: Universal TUN/TAP device driver, 1.6
[ 17.768914] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 17.812569] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 17.854855] Loading modules backported from Linux version wt-2017-01-31-0-ge882dff19e7f
[ 17.870878] Backport generated by backports.git backports-20160324-13-g24da7d3c
[ 18.060578] u32 classifier
[ 18.065970] input device check on
[ 18.073313] Actions configured
[ 18.108790] Mirror/redirect action on
[ 18.129348] nf_conntrack version 0.5.0 (949 buckets, 3796 max)
[ 18.184662] fuse init (API version 7.23)
[ 18.206104] usbcore: registered new interface driver cdc_acm
[ 18.217456] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 18.278253] usbcore: registered new interface driver cdc_wdm
[ 18.301105] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 18.449023] usbcore: registered new interface driver usblp
[ 18.492493] usbcore: registered new interface driver usbserial
[ 18.504292] usbcore: registered new interface driver usbserial_generic
[ 18.517449] usbserial: USB Serial support registered for generic
[ 18.643651] xt_time: kernel timezone is -0000
[ 18.664753] usbcore: registered new interface driver cdc_ether
[ 18.700672] usbcore: registered new interface driver cdc_ncm
[ 18.728008] usbcore: registered new interface driver huawei_cdc_ncm
[ 18.796001] PPP generic driver version 2.4.2
[ 18.829169] NET: Registered protocol family 24
[ 18.855008] usbcore: registered new interface driver qmi_wwan
[ 18.879571] usbcore: registered new interface driver rndis_host
[ 18.955834] rt2800_wmac 10180000.wmac: loaded eeprom from mtd device "factory"
[ 18.970315] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 6352, rev 0500 detected
[ 18.985771] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 7620 detected
[ 19.054371] usbcore: registered new interface driver sierra
[ 19.065662] usbserial: USB Serial support registered for Sierra USB modem
[ 19.112633] usbcore: registered new interface driver sierra_net
[ 19.152904] usbcore: registered new interface driver cdc_mbim
[ 19.178798] usbcore: registered new interface driver option
[ 19.190084] usbserial: USB Serial support registered for GSM modem (1-port)
[ 19.242204] usbcore: registered new interface driver qcserial
[ 19.253851] usbserial: USB Serial support registered for Qualcomm USB modem
[ 19.296417] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 30.377819] 8021q: adding VLAN 0 to HW filter on device eth0
[ 30.408805] device eth0.1 entered promiscuous mode
[ 30.418426] device eth0 entered promiscuous mode
[ 30.467557] br-lan: port 1(eth0.1) entered forwarding state
[ 30.478761] br-lan: port 1(eth0.1) entered forwarding state
[ 32.476592] br-lan: port 1(eth0.1) entered forwarding stateA i jeszcze jedno. Przy próbie wgrania tego samego obrazu mamy komunikat:
root@LEDE:/tmp# sysupgrade -n luci-17.01-snapshot-r3371-79cd141-ramips-mt7620-wt
3020-16M-squashfs-sysupgrade.bin
Device generic not supported by this image
Supported devices: wt3020-16M
Image check 'fwtool_check_image' failed.
root@LEDE:/tmp#I czy przypadkiem problemem nie jest brak konfiguracji switcha?
root@LEDE:/# cat /etc/config/network
config interface 'loopback'
option ifname 'lo'
option proto 'static'
option ipaddr '127.0.0.1'
option netmask '255.0.0.0'
config globals 'globals'
option ula_prefix 'fd7d:b5cf:76b8::/48'
config interface 'lan'
option type 'bridge'
option ifname 'eth0.1'
option proto 'static'
option ipaddr '192.168.1.1'
option netmask '255.255.255.0'
option ip6assign '60'
config device 'lan_dev'
option name 'eth0.1'
option macaddr '20:28:18:a1:f0:32'
config interface 'wan'
option ifname 'eth0.2'
option proto 'dhcp'
config device 'wan_dev'
option name 'eth0.2'
option macaddr '20:28:18:a1:f0:33'
config interface 'wan6'
option ifname 'eth0.2'
option proto 'dhcpv6'
root@LEDE:/#Źle wykrywana platforma, problem naprawia patch który podałem wyżej. Poczekaj do wieczora.
Tak czy siak po dopisaniu konfiguracji switcha sieć się podnosi.
Zobacz jeszcze czy normalnie uruchamia się w failsafe i czy wtedy jest sieć.
Failsafe działa, jest sieć (odpowiada na ping) ale nie można się do niego dostać.
Przez ssh?
No tak, próbowałem przez telnet. SSH działa.
Wgraj te obrazy: http://dl.eko.one.pl/test/ i zobacz.
Wgraj te obrazy: http://dl.eko.one.pl/test/ i zobacz.
W dalszym ciągu dioda nie miga podczas uruchamiania, nie ma konfiguracji switcha, nie ma sieci i dodatkowo
Flash: total: 29.7MB, free: 29.6MB, used: 0% Restartowałem dwa razy i za każdym razem to samo.
EDIT:
Po kilku minutach:
[ 320.712643] done.
[ 320.716520] jffs2: notice: (896) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.z flash wszystko OK ale sieci nie ma.
Pokaż
cat /tmp/sysinfo/*
root@LEDE:/# cat /tmp/sysinfo/*
wt3020-16M
Nexx WT3020 (16M)
root@LEDE:/#Dobra, zmiana planów. Weź obraz jeszcze raz i wgraj ponownie.
Zobacz później co w /etc/config/network będzie.
Cezary, manipulowałes plikami z linka który podałeś wyżej?
Ja dodałem sekcje dla wt3020-16M, dodałem dts-a dla 16M, skopilowałem i jak na razie wszystko mi działa.
Poza tym, że nadal zgłasza się jako WT3020-8M (na podstawie mac-adresu)
i przy próbie aktualizacji przez sysupgrade wrzeszczy, że "Supported device WT3020-16M" i trzeba dodać -F
Masz nic nie dodawać tylko ma działać od razu.
Dioda miga, konfiguracja switcha jest, sieć działa.
root@LEDE:~# cat /etc/config/network
config interface 'loopback'
option ifname 'lo'
option proto 'static'
option ipaddr '127.0.0.1'
option netmask '255.0.0.0'
config globals 'globals'
option ula_prefix 'fd75:0a5d:7047::/48'
config interface 'lan'
option type 'bridge'
option ifname 'eth0.1'
option proto 'static'
option ipaddr '192.168.1.1'
option netmask '255.255.255.0'
option ip6assign '60'
config device 'lan_dev'
option name 'eth0.1'
option macaddr '20:28:18:a1:f0:32'
config interface 'wan'
option ifname 'eth0.2'
option proto 'dhcp'
config device 'wan_dev'
option name 'eth0.2'
option macaddr '20:28:18:a1:f0:33'
config interface 'wan6'
option ifname 'eth0.2'
option proto 'dhcpv6'
config switch
option name 'switch0'
option reset '1'
option enable_vlan '1'
config switch_vlan
option device 'switch0'
option vlan '1'
option ports '1 2 3 4 6t'
config switch_vlan
option device 'switch0'
option vlan '2'
option ports '0 6t'
root@LEDE:~#Upgrade z -F, bo inaczej:
root@LEDE:/tmp# sysupgrade -n lede-17.01-snapshot-r3422-b78bcdf-ramips-mt7620-wt
3020-16M-squashfs-sysupgrade.bin
Sysupgrade is not yet supported on wt3020.
Image check 'platform_check_image' failed.
root@LEDE:/tmp#Czyli działa.
Trochę bez sensu, sysupgrade też powinno działać. Możesz śmiało przez -F robić.
Wszystko jest OK z wyjątkiem sysupgrade. Na tym obrazie też wyrzuca:
root@LEDE:/tmp# sysupgrade -n lede-17.01-snapshot-r3422-b78bcdf-ramips-mt7620-wt
3020-16M-squashfs-sysupgrade.bin
Device wt3020 not supported by this image
Supported devices: wt3020-16M
Image check 'fwtool_check_image' failed.
root@LEDE:/tmp#Teraz przynajmniej wiem czemu mój Nexx jest jedyny w statystykach
Skopiowałem stare konfigi z CC i dzięki temu switch ożył. Inni wgrali obraz 8M albo zostali na CC ![]()
Uprościłem sprawę i wszystkie odmiany nazwałem tak samo. Nie wiem czy mi się chce przenosić całego patcha z wersji rozwojowej.
Strony Poprzednia 1 … 14 15 16 17 18 … 21 Następna
Zaloguj się lub zarejestruj by napisać odpowiedź
eko.one.pl → Oprogramowanie / Software → NEXX WT3020H
Forum oparte o PunBB, wspierane przez Informer Technologies, Inc