Komuś się udało uruchomić OpenWRT 24.10 na Linksys EA8300? Na moich dwóch urządzeniach, próby aktualizacji zakończyły się tylko miganiem LEDów przy podłączonych portach LAN. Dzisiaj pobawiłem się lutownicą i do jednego podłączyłem się portem szeregowym i konsola wypluła mi coś takiego:
Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.1.1-00108
S - IMAGE_VARIANT_STRING=DAACANAZA
S - OEM_IMAGE_VERSION_STRING=CRM
S - Boot Config, 0x00000025
S - Reset status Config, 0x00000000
S - Core 0 Frequency, 0 MHz
B - 261 - PBL, Start
B - 1338 - bootable_media_detect_entry, Start
B - 2610 - bootable_media_detect_success, Start
B - 2624 - elf_loader_entry, Start
B - 4031 - auth_hash_seg_entry, Start
B - 6182 - auth_hash_seg_exit, Start
B - 74204 - elf_segs_hash_verify_entry, Start
B - 196013 - PBL, End
B - 196037 - SBL1, Start
B - 288061 - pm_device_init, Start
D - 7 - pm_device_init, Delta
B - 289552 - boot_flash_init, Start
D - 87146 - boot_flash_init, Delta
B - 381000 - boot_config_data_table_init, Start
D - 13963 - boot_config_data_table_init, Delta - (419 Bytes)
B - 397717 - clock_init, Start
D - 7584 - clock_init, Delta
B - 408735 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:0,Subtype:6
B - 412147 - sbl1_ddr_set_params, Start
B - 417240 - cpr_init, Start
D - 2 - cpr_init, Delta
B - 421622 - Pre_DDR_clock_init, Start
D - 4 - Pre_DDR_clock_init, Delta
D - 13169 - sbl1_ddr_set_params, Delta
B - 434925 - pm_driver_init, Start
D - 2 - pm_driver_init, Delta
B - 504771 - sbl1_wait_for_ddr_training, Start
D - 28 - sbl1_wait_for_ddr_training, Delta
B - 520100 - Image Load, Start
D - 143769 - QSEE Image Loaded, Delta - (269176 Bytes)
B - 664295 - Image Load, Start
D - 2118 - SEC Image Loaded, Delta - (2048 Bytes)
B - 674430 - Image Load, Start
D - 186996 - APPSBL Image Loaded, Delta - (444263 Bytes)
B - 861822 - QSEE Execution, Start
D - 56 - QSEE Execution, Delta
B - 868022 - SBL1, End
D - 674093 - SBL1, Delta
S - Flash Throughput, 2089 KB/s (715906 Bytes, 342594 us)
S - DDR Frequency, 672 MHz
U-Boot 2012.07 [Chaos Calmer 15.05.1,r35193] (Nov 02 2017 - 16:33:09)
CBT U-Boot ver: 1.2.9
smem ram ptable found: ver: 1 len: 3
DRAM: 256 MiB
machid : 0x8010006
NAND: ID = 9590dac2
Vendor = c2
Device = da
ONFI device found
SF NAND unsupported id:ff:ff:ff:ffSF: Unsupported manufacturer ff
ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0)
256 MiB
MMC: qca_mmc: 0
PCI0 Link Intialized
In: serial
Out: serial
Err: serial
machid: 8010006
flash_type: 2
Net: MAC0 addr:0:3:7f:ba:db:ad
PHY ID1: 0x4d
PHY ID2: 0xd0b1
ipq40xx_ess_sw_init done
eth0
Updating boot_count ... done
Hit any key to stop autoboot: 0
Memory test start, banksize=0x2000000, data size=0x8000, test count per bank=64
Memory test end, lapsed time = 3 seconds
The test result is success
NAND read: device 0 offset 0x780000, size 0x300000
3145728 bytes read: OK
## Booting kernel from FIT Image at 84000000 ...
Bad FIT kernel image format!
ERROR: can't get kernel image!
(IPQ40xx) #
).