Doszedłem który pin jest rxd ktory txd według tego http://www.devttys0.com/2012/11/reverse … ial-ports/. Niestety, ale kabla nie zrobiłem. Układ na max232 się nie nadaję a tego 3232 nie mam w swoich zbiorach. Kabel dlr-3p nie działa, bawiłem się nim, ale on jest chyba na max3237. Poszukam jutro jeszcze w szpargałach może coś wynajdę, ale obawiam się, że nie 
Zrobiłem dzisiaj 2 układy i żaden nie działa. Co za pech.
Haha a jednak udało mi się jednak odpalić dlinka na tym kablu dlr3, zaraz spróbuję dgt, ale pewnie pójdzie 
Odpaliłem mtty i działa. W putty wywala krzaki na dgt.
CFE version 1.0.37-106.17 for BCM96368 (32bit,SP,BE)
Build Date: Wed Feb 9 15:29:15 CET 2011 (krom@krom)
Copyright (C) 2000-2009 Broadcom Corporation.
Parallel flash device: name AM29LV320MT, id 0x2201 size 32768KB
Total Flash size: 32768K with 256 sectors
w #02 @00 := 8000
w #02 @1a := 4000
w #02 @1b := 008e
w #02 @00 := 3200
w #03 @00 := 8000
w #03 @1a := 4000
w #03 @1b := 008e
w #03 @00 := 3200
w #18 @00 := 8000
w #18 @00 := 8000
w #18 @04 := 01e1
w #18 @1c := 2400
w #18 @1c := a418
w #18 @1c := 0c00
w #18 @1c := 8c00
w #18 @1c := 2c00
w #18 @1c := ac84
w #18 @1c := a410
w #18 @1c := b40e
w #18 @1c := 8804
w #18 @00 := 1340
w #19 @00 := 8000
w #19 @00 := 8000
w #19 @04 := 01e1
w #19 @1c := 2400
w #19 @1c := a418
w #19 @1c := 0c00
w #19 @1c := 8c00
w #19 @1c := 2c00
w #19 @1c := ac84
w #19 @1c := a410
w #19 @1c := b40e
w #19 @1c := 8804
w #19 @00 := 1340
Chip ID: BCM6368B2, MIPS: 400MHz
Main Thread: TP0
Total Memory: 67108864 bytes (64MB)
Boot Address: 0xb8000000
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Boot image (0=latest, 1=previous) : 0
Board Id (0-3) : DGT0730A
Number of MAC Addresses (1-32) : 10
Base MAC Address :
PSI Size (1-64) KBytes : 24
Enable Backup PSI [0|1] : 0
System Log Size (0-256) KBytes : 0
Main Thread Number [0|1] : 0
Voice Board Configuration (0-3) : DGT0730A
DGT serial :
DGT mode : 0x00
Default WPA key :
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
Booting from latest image (0xb8040000) ...
Code Address: 0x80010000, Entry Address: 0x80014230
Decompression OK!
Entry at 0x80014230
Closing network.
Disabling Switch ports.
Flushing Receive Buffers...
0 buffers found.
Closing DMA Channels.
Starting program at 0x80014230
Linux version 2.6.30 (root@texas) (gcc version 4.4.2 (Buildroot 2010.02-git) ) #6 Wed Apr 6 17:03:52 CEST 2011
Parallel flash device: name AM29LV320MT, id 0x2201 size 32768KB
DGT0730A prom init
Linux TP ID = 0
CPU revision is: 0002a031 (Broadcom4350)
Determined physical RAM map:
memory: 03f00000 @ 00000000 (usable)
Zone PFN ranges:
DMA 0x00000000 -> 0x00001000
Normal 0x00001000 -> 0x00003f00
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00003f00
On node 0 totalpages: 16128
free_area_init_node: node 0, pgdat 8034c310, node_mem_map 81000000
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 94 pages used for memmap
Normal zone: 11938 pages, LIFO batch:1
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16002
Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
wait instruction: enabled
Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.
Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
RCU-based detection of stalled CPUs is enabled.
NR_IRQS:128
PID hash table entries: 256 (order: 8, 1024 bytes)
console [ttyS0] enabled
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Allocating memory for DSP module core and initialization code
Allocated DSP module memory - CORE=0x8108c720 SIZE=1889440, INIT=0x81259bc0 SIZE=44
Memory: 58340k/64512k available (2630k kernel code, 6152k reserved, 686k data, 124k init, 0k highmem)
Calibrating delay loop... 399.36 BogoMIPS (lpj=199680)
Mount-cache hash table entries: 512
net_namespace: 820 bytes
NET: Registered protocol family 16
Total Flash size: 32768K with 256 sectors
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
pci 0000:00:01.0: reg 10 32bit mmio: [0x000000-0x00ffff]
pci 0000:00:09.0: reg 10 32bit mmio: [0x10001600-0x100016ff]
pci 0000:00:0a.0: reg 10 32bit mmio: [0x10001500-0x100015ff]
BLOG v2.1 Initialized
NET: Registered protocol family 8
NET: Registered protocol family 20
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
squashfs: version 4.0 with LZMA457 ported by BRCM
fuse init (API version 7.11)
msgmni has been set to 113
io scheduler noop registered (default)
Driver 'sd' needs updating - please use bus_type methods
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
NET: Registered protocol family 24
usbcore: registered new interface driver cdc_ether
bcm963xx_mtd driver v1.0
File system address: 0xb8040400
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:0a.0 to 64
ehci_hcd 0000:00:0a.0: EHCI Host Controller
ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:0a.0: Enabling legacy PCI PM
ehci_hcd 0000:00:0a.0: irq 15, io mem 0x10001500
ehci_hcd 0000:00:0a.0: USB f.f started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:09.0 to 64
ohci_hcd 0000:00:09.0: OHCI Host Controller
ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:09.0: irq 13, io mem 0x10001600
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usbcore: registered new interface driver usblp
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
brcmboard: brcm_board_init entry
SES: Button Interrupt 0x1 is enabled
SES: LED GPIO 0x17 is enabled
Serial: BCM63XX driver $Revision: 3.00 $
ttyS0 at MMIO 0xb0000100 (irq = 10) is a BCM63XX
ttyS1 at MMIO 0xb0000120 (irq = 11) is a BCM63XX
bcmxtmrt: Broadcom BCM6368B2 ATM/PTM Network Device v0.3 Apr 6 2011 14:34:47
Broadcom Logger v0.1 Apr 6 2011 14:33:09
IPSEC SPU: SUCCEEDED
Mirror/redirect action on
u32 classifier
input device check on
Actions configured
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 17
NET: Registered protocol family 15
Initializing MCPD Module
Ebtables v2.0 registered
ebt_time registered
ebt_ftos registered
ebt_wmm_mark registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:0.
Freeing unused kernel memory: 124k freed
init started: BusyBox v1.00 (2011.04.06-12:41+0000) multi-call binary
/sbin/inetd: not found
BusyBox v1.00 (2011.04.06-12:41+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.
Loading drivers and kernel modules...
pktflow: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
Broadcom Packet Flow Cache Char Driver v2.1 Jun 11 2010 16:20:25 Registered<242>
NBUFF v1.0 Initialized
Broadcom Packet Flow Cache learning via BLOG enabled.
Created Proc FS /procfs/fcache
Broadcom Packet Flow Cache registered with netdev chain
Constructed Broadcom Packet Flow Cache v2.1 Jun 11 2010 16:20:24
Broadcom Packet CMF (Experimental) Char Driver v0.1 Jun 11 2010 16:20:22 Registered<232>
Broadcom Packet CMF (Experimental) [6368-B2] v0.1 Jun 11 2010 16:20:22 Loaded
bcmxtmcfg: bcmxtmcfg_init entry
adsl: adsl_init entry
Broadcom BCM6368B2 Ethernet Network Device v0.1 Apr 6 2011 14:34:34
ETH Init: 180 tx BDs at 0xa397a000
ETH Init: 400 rx BDs at 0xa3a90000
ETH Init: 400 rx BDs at 0xa39e3000
dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered
Broadcom Packet CMF (Experimental) SWC RESET.
Broadcom Packet CMF (Experimental) SWC INITIALIZED.
Broadcom Packet CMF (Experimental) Forwarder Net Device 0 v0.1 Jun 11 2010 16:20:23 Registered
Broadcom Packet CMF (Experimental) Forwarder Net Device 0 v0.1 Jun 11 2010 16:20:23 Registered
Broadcom Packet CMF (Experimental) ENABLED.
eth0: MAC Address:
eth1: MAC Address:
eth2: MAC Address:
eth3: MAC Address:
Broadcom BCM6368B2 USB Network Device v0.4a Apr 6 2011 14:34:39
usb0: MAC Address:
usb0: Host MAC Address:
USBD Initialization done status 0
USB Link DOWN.
message received before monitor task is initialized kerSysSendtoMonitorTask
PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:01.0 to 64
wl:srom not detected,using main memory mapped srom info(wombo board)
wl:loading /etc/wlan/bcm43222_map.bin
wl0: Broadcom BCMa8d6 802.11 Wireless Controller 5.60.120.1.cpe4.06L02.2
dgasp: kerSysRegisterDyingGaspHandler: wl0 registered
IRQ 21/brcm_21: IRQF_DISABLED is not guaranteed on shared IRQs
DSP Driver: DSP init stub
Endpoint: endpoint_init entry
deviceChannelMap[0].txTimeslot = 4
deviceChannelMap[1].txTimeslot = 6
Endpoint: endpoint_init COMPLETED
p8021ag: p8021ag_init entry
Broadcom 802.1Q VLAN Interface, v0.1
243
==============================================================
NOT cmf disable
NOT fc disable
==============================================================
===== Release Version 4.06L.02 (build timestamp 110406_1702) =====
ssk:error:12.609:BOS: Enter bosInit
lck_checkBeforeEEnter bosAppInit
ntry:171:lock reExit bosAppInit
quired during cmBOS: Exit bosInit
sObj_getNextInSuendpoint_open COMPLETED
bTreeFlags
interface atm1 does not exist!
SIOCGIFFLAGS: No such device
interface atm2 does not exist!
SIOCGIFFLAGS: No such device
interface ptm0.2 does not exist!
SIOCGIFFLAGS: No such device
interface ptm0.3 does not exist!
SIOCGIFFLAGS: No such device
ip_tables: (C) 2000-2006 Netfilter Core Team
device eth2 entered promiscuous mode
device eth3 entered promiscuous mode
device eth0 entered promiscuous mode
device usb0 entered promiscuous mode
device wl0 entered promiscuous mode
br0: port 5(wl0) entering forwarding state
WLmngr Daemon is running
optarg=0 shmId=0
wlevt_init@107: opened loopback socket 4
wlevt is ready for new msg...
SIOCSIFNETMASK: Cannot assign requested address
SIOCSIFBRDADDR: Cannot assign requested address
device eth1 entered promiscuous mode
BcmAdsl_Initialize=0xC017C0F8, g_pFnNotifyCallback=0xC01B7924
Clocks for QPROC and AFE are being aligned with step through ...
AFE is aligned, i = 065, PhaseValue = -150, PhaseCntl = 0x7FC00000
QPROC is aligned, i = 068, PhaseValue = -082, PhaseCntl = 0x7FC07FBD
Clocks for QPROC and AFE are aligned with syn_status AFE = 0x78, QPROC = 0x78
AFE phase control reg @0xb0f570f8 default actual = 0x0021C38F, exp = 0x0021c38f
QPRC phase control reg @0xb0f5f0c0 default actual = 0x0421C38F, exp = 0x0421c38f
pSdramPHY=0xA3FFFFF8, 0xEFFFFDFF 0xEDFFFFFF
*** XfaceOffset: 0x5FF90 => 0x5FF90 ***
*** PhySdramSize got adjusted: 0xBDCC0 => 0xEB3E0 ***
AdslCoreSharedMemInit: shareMemAvailable=84992
AdslCoreHwReset: pLocSbSta=82ca0000 bkupThreshold=3072
AdslCoreHwReset: AdslOemDataAddr = 0xA3FB3638
dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered
XTM Init: 400 rx BDs at 0xa25dc000
XTM Init: 100 rx BDs at 0xa25b0000
monitor task is initialized pid= 253
ssk:error:19.753:initVodslBoundIpIfWanSideUpLocked:423:Failed to get WAN Connection object
ssk:error:19.753:enable_http_redirection:2816:Enabling HTTP redirection
usage: hotplug [event]
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (1008 buckets, 4032 max)
ctnetlink v0.93: registering with nfnetlink.
killall: dnsspoof: no process killed
device wl0 left promiscuous mode
br0: port 5(wl0) entering disabled state
device wl0 entered promiscuous mode
br0: port 5(wl0) entering forwarding state
wl0.1 (): not using net_device_ops yet
wl0.2 (): not using net_device_ops yet
wl0.3 (): not using net_device_ops yet
br0: port 5(wl0) entering disabled state
There is no Predefined DevicePin in CFE
WPS Device PIN = 10864111
Setting SSID: "DGT_VDSL"
Setting SSID: "wl0_Guest1"
Setting SSID: "wl0_Guest2"
Setting SSID: "wl0_Guest3"
chanspec 0x2b06 selected
device wl0 left promiscuous mode
br0: port 5(wl0) entering disabled state
device wl0 entered promiscuous mode
br0: port 5(wl0) entering forwarding state
Reaped 1029
UPnP daemon is ready to run
Wygląda na to, że fg4 ma takie same bebechy http://openlinksys.info/forum/viewthrea … d_id=15380 Jutro przeanalizuję.
A nie mogę się zalogować nie wiem jakie hasło i login, domyślne admin admin i root root, nie pasują.
Ok nie ma to znaczenia przy wgrywaniu, wystarczy enter wcisnąć. Biorę się za backup ori firmware, miałem gdzieś chyba go, ale nie wiem czy nie wywaliłem.
Problem 1. Nie bardzo wiem jak zgrać ori firmware.
Problem 2. Czy można wgrać openwrt przez oryginalny interfejs dgt?
Na dzisiaj się poddaje, jutro wezmę się za robotę.
ThinClient fan
I tak już nie mam neostrady. Czytałem, że jeszcze nie działby voip. Ten chip to chyba 6368, ale musiałbym sprawdzić. Na dodatek 2 porty Lan 1gbit są obługiwane przez osobne chipy b50610c1kmlg bo bcm6368 ma porty tylko 100mbit.