Dobra, ogarniam:
Na wan (eth0.2) wchodzi 20 i dalej z portu lan3 (np. eth0.3) wychodzi 15 i z portu lan4 (eth0.4) wychodzi 5,
razem 20, tyle co weszło (ruch przychodzący) na wan, wyszło (ruch wychodzący) przez lany.
Teraz chciałbym to trochę uporządkować.
Sieć ma wyglądać tak:
wifi i lan1, jedna sieć, dhcp 192.168.1.100-192.168.1.200
lan2, dhcp 192.168.2.100-192.168.2.200
lan3, dhcp 192.168.3.100-192.168.3.200
lan4, dhcp 192.168.4.100-192.168.4.200
ustawienia network
config interface 'loopback'
option ifname 'lo'
option proto 'static'
option ipaddr '127.0.0.1'
option netmask '255.0.0.0'
config interface 'lan'
option ifname 'eth0.1'
option type 'bridge'
option proto 'static'
option ipaddr '192.168.1.1'
option netmask '255.255.255.0'
config interface 'wan'
option ifname 'eth0.2'
option _orig_ifname 'eth0.2'
option _orig_bridge 'false'
option proto 'pppoe'
option username '*********'
option password '*********'
config interface 'vlan12'
option ifname 'eth0.12'
option proto 'static'
option ipaddr '192.168.2.1'
option netmask '255.255.255.0'
config interface 'vlan3'
option ifname 'eth0.3'
option proto 'static'
option ipaddr '192.168.3.1'
option netmask '255.255.255.0'
config interface 'vlan4'
option ifname 'eth0.4'
option proto 'static'
option ipaddr '192.168.4.1'
option netmask '255.255.255.0'
config switch
option name 'rtl8366rb'
option reset '1'
option enable_vlan '1'
config switch_vlan
option device 'rtl8366rb'
option vlan '1'
option ports '1 5t'
config switch_vlan
option device 'rtl8366rb'
option vlan '2'
option ports '0 5t'
config switch_vlan
option device 'rtl8366rb'
option vlan '12'
option ports '2 5t'
config switch_vlan
option device 'rtl8366rb'
option vlan '3'
option ports '3 5t'
config switch_vlan
option device 'rtl8366rb'
option vlan '4'
option ports '4 5t'
ustawienia dhcp
config dnsmasq
option domainneeded 1
option boguspriv 1
option filterwin2k 0 # enable for dial on demand
option localise_queries 1
option rebind_protection 1 # disable if upstream must serve RFC1918 addresses
option rebind_localhost 1 # enable for RBL checking and similar services
#list rebind_domain example.lan # whitelist RFC1918 responses for domains
option local '/lan/'
option domain 'lan'
option expandhosts 1
option nonegcache 0
option authoritative 1
option readethers 1
option leasefile '/tmp/dhcp.leases'
option resolvfile '/tmp/resolv.conf.auto'
#list server '/mycompany.local/1.2.3.4'
#option nonwildcard 1
#list interface br-lan
#list notinterface lo
#list bogusnxdomain '64.94.110.11'
config dhcp lan
option interface lan
option start 100
option limit 150
option leasetime 12h
config dhcp wan
option interface wan
option ignore 1
config dhcp 'vlan12'
option interface 'vlan12'
option start '100'
option limit '150'
option leasetime '12h'
config dhcp 'vlan3'
option interface 'vlan3'
option start '100'
option limit '150'
option leasetime '12h'
config dhcp 'vlan4'
option interface 'vlan4'
option start '100'
option limit '150'
option leasetime '12h'
Nie znam się zbyt na sieciach,
ale chciałbym usunąć z tych wykresów zakładki br-lan i eth0
czy można je jakoś usunąć, czy bez tego może sieć nie będzie działać prawidłowo?
