1 Temat przez Zawisza (edytowany przez Cezary 2010-09-08 05:46:32)

  • Zarejestrowany: 2010-09-07
  • Posty: 39

Temat: OpenWrt zwałka na wrt54g3gv2-vf

Przedwczoraj podjąłem decyzję, wgrywam alternatywny firmware do ruterka - OpenWrt. Po pierwszym podniesieniu się i kilku zmianach w konfigu karty WiFi ruter już nie wstał. Co ciekawe na pingi odpowiadał ale to wszystko. A więc odzysk firmweru po tftp i nic. Zmajstrowałem kabelek RS232 z tego co miałem tj. kabel nokia DLR-3P i podpoiłem się. Ucieszyłem się gdy zobaczyłem komunikaty jednak rooter nie przyjmował żadnych poleceń. i tu moje pytanie
1.czy ktoś wie jaki może być powód (kabel TX sprawdzałem i wygląda OK).
2.co mi ten ruter chce powiedzieć przez te logi:
CFE version 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: Thu Aug  7 16:44:55 CST 2008 (root@localhost.localdomain)
Copyright (C) 2000,2001,2002,2003 Broadcom Corporation.

Initializing Arena
Initializing Devices.

No DPN
This is a Parallel Flash
Boot partition size = 262144(0x40000)
Try 4: vendor id = 0x0001, device id = 0x2201
Flash type is "S29GL128N10TFI010 8Mx16"
Total size is 0x1000000.
Block size is 0x20000.
Total blocks are 122. (Image 1 are 61(7995392), Image 2 is 61(7995392))
Partition information:
boot    #00   00000000 -> 0003FFFF  (262144)
trx     #01   00040000 -> 0004001F  (32)
os      #02   00040020DFFFF  (7995360)
trx2    #03   007E0000 -> 007E001F  (32)
os2     #04   007E0020 -> 00F7FFFF  (7995360)
lang    #05   00F80000 -> 00FF7FFF  (491520)
nvram   #06   00FF8000 -> 00FFFFFF  (32768)
Partition information:
boot    #00   00000000 -> 0003FFFF  (262144)
trx     #01   00040000 -> 007DFFFF  (7995392)
trx2    #02   007E0000 -> 00F7FFFF  (7995392)
lang    #03   00F80000 -> 00FF7FFF  (491520)
nvram   #04   00FF8000 -> 00FFFFFF  (32768)
et0: Broadcom BCM47xx 10/100 Mbps Ethernet Controller 4.150.10.5
et1: Broadcom BCM47xx 10/100 Mbps Ethernet Controller 4.150.10.5
CPU type 0x29006: 264MHz
Total memory: 32768 KBytes

Total memory used by CFE:  0x80700000 - 0x807A51F0 (676336)
Initialized Data:          0x8073B950 - 0x8073E9A0 (12368)
BSS Area:                  0x8073E9A0 - 0x8073F1F0 (2128)
Local Heap:                0x8073F1F0 - 0x807A31F0 (409600)
Stack Area:                0x807A31F0 - 0x807A51F0 (8192)
Text (code) segment:       0x80700000 - 0x8073B950 (244048)
Boot area (physical):      0x007A6000 - 0x007E6000
Relocation Factor:         I:00000000 - D:00000000

Boot version: v5.5
The boot is CFE

mac_init(): Find mac [00:23:69:57:2F:0D] in location 0
Nothing...
CMD: [ifconfig eth0 -addr=192.168.1.1 -mask=255.255.255.0]
Device eth0:  hwaddr 00-23-69-57-2F-0D, ipaddr 192.168.1.1, mask 255.255.255.0
        gateway not set, nameserver not set
CMD: [go;]
Check CRC of image1
  Len:     0xDA400    (893952)    (0xBC040000)
  Offset0: 0x20        (32)        (0xBC040020)
  Offset1: 0x978    (2424)    (0xBC040978)
  Offset2: 0xDA400    (893952)    (0xBC11A400)
  Offset3: 0x2A1D1C    (2759964)    (0xBC2E1D1C)
  Version: v3.0.24 #006
  Stable:  0xFF
  Try:     0x74, 0x74, 0x74
Try three time, and can't boot the image, maybe the image is bad. (Set skip_check_flag=1 to skip check.)
Check CRC of image2
Invalid boot block on disk
CMD: [flash -ctheader : flash1.trx]
Reading :: Failed.: Timeout occured

i tak te dwa ostatnie komunikaty non stop
natomiast po wgraniu firmweru
C:\Documents and Settings\paytel>tftp -i 192.168.1.1 PUT "c:\Documents and Settings\paytel\Moje dokumenty\Downloads\openwrt-wrt54g3gv2-vf-squashfs.bin"
ok.3 bootowania wyględają następująco:
CFE version 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: Thu Aug  7 16:44:55 CST 2008 (root@localhost.localdomain)
Copyright (C) 2000,2001,2002,2003 Broadcom Corporation.

Initializing Arena
Initializing Devices.

No DPN
This is a Parallel Flash
Boot partition size = 262144(0x40000)
Try 4: vendor id = 0x0001, device id = 0x2201
Flash type is "S29GL128N10TFI010 8Mx16"
Total size is 0x1000000.
Block size is 0x20000.
Total blocks are 122. (Image 1 are 61(7995392), Image 2 is 61(7995392))
Partition information:
boot    #00   00000000 -> 0003FFFF  (262144)
trx     #01   00040000 -> 0004001F  (32)
os      #02   00040020 -> 007DFFFF  (7995360)
trx2    #03   007E0000 -> 007E001F  (32)
os2     #04   007E0020 -> 00F7FFFF  (7995360)
lang    #05   00F80000 -> 00FF7FFF  (491520)
nvram   #06   00FF8000 -> 00FFFFFF  (32768)
Partition information:
boot    #00   00000000 -> 0003FFFF  (262144)
trx     #01   00040000 -> 007DFFFF  (7995392)
trx2    #02   007E0000 -> 00F7FFFF  (7995392)
lang    #03   00F80000 -> 00FF7FFF  (491520)
nvram   #04   00FF8000 -> 00FFFFFF  (32768)
et0: Broadcom BCM47xx 10/100 Mbps Ethernet Controller 4.150.10.5
et1: Broadcom BCM47xx 10/100 Mbps Ethernet Controller 4.150.10.5
CPU type 0x29006: 264MHz
Total memory: 32768 KBytes

Total memory used by CFE:  0x80700000 - 0x807A51F0 (676336)
Initialized Data:          0x8073B950 - 0x8073E9A0 (12368)
BSS Area:                  0x8073E9A0 - 0x8073F1F0 (2128)
Local Heap:                0x8073F1F0 - 0x807A31F0 (409600)
Stack Area:                0x807A31F0 - 0x807A51F0 (8192)
Text (code) segment:       0x80700000 - 0x8073B950 (244048)
Boot area (physical):      0x007A6000 - 0x007E6000
Relocation Factor:         I:00000000 - D:00000000

Boot version: v5.5
The boot is CFE

mac_init(): Find mac [00:23:69:57:2F:0D] in location 0
Nothing...
CMD: [ifconfig eth0 -addr=192.168.1.1 -mask=255.255.255.0]
Device eth0:  hwaddr 00-23-69-57-2F-0D, ipaddr 192.168.1.1, mask 255.255.255.0
        gateway not set, nameserver not set
CMD: [go;]
Check CRC of image1
  Len:     0xDA400    (893952)    (0xBC040000)
  Offset0: 0x20        (32)        (0xBC040020)
  Offset1: 0x978    (2424)    (0xBC040978)
  Offset2: 0xDA400    (893952)    (0xBC11A400)
  Offset3: 0x2A1D1C    (2759964)    (0xBC2E1D1C)
  Version: v3.0.24 #006
  Stable:  0xFF
  Try:     0x74, 0x74, 0xFF
  Header CRC:    0x7C2B6036
  Calculate CRC: 0x7C2B6036
Image 1 is OK
Check CRC of image2
Invalid boot block on disk
Image Status : IMG2_BAD
Try to load image 1.
Change to load image 1.
Write 't' to 0x2E1D38 (0xBC2E1D38)
Try 4: vendor id = 0x0001, device id = 0x2201
Flash type is "S29GL128N10TFI010 8Mx16"
Write 2 bytes from 2E1D38 to 2E1D3A
Write 2 bytes
CMD: [boot -raw -z -addr=0x80001000 -max=0xf40000 flash0.os:]
Loader:raw Filesys:raw Dev:flash0.os File: Options:(null)
Loading: .. 4092 bytes read
Entry at 0x80001000
Closing network.
Starting program at 0x80001000
Linux version 2.6.32.10 (openwrt@wrt1.marcant.net) (gcc version 4.3.3 (GCC) ) #20 Tue Apr 6 15:53:48 CEST 2010
CPU revision is: 00029006 (Broadcom BCM3302)
ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x03, vendor 0x4243)
ssb: Core 1 found: Fast Ethernet (cc 0x806, rev 0x06, vendor 0x4243)
ssb: Core 2 found: Fast Ethernet (cc 0x806, rev 0x06, vendor 0x4243)
ssb: Core 3 found: USB 1.1 Hostdev (cc 0x808, rev 0x03, vendor 0x4243)
ssb: Core 4 found: PCI (cc 0x804, rev 0x08, vendor 0x4243)
ssb: Core 5 found: MIPS 3302 (cc 0x816, rev 0x03, vendor 0x4243)
ssb: Core 6 found: V90 (cc 0x807, rev 0x02, vendor 0x4243)
ssb: Core 7 found: IPSEC (cc 0x80B, rev 0x00, vendor 0x4243)
ssb: Core 8 found: MEMC SDRAM (cc 0x80F, rev 0x02, vendor 0x4243)
ssb: Initializing MIPS core...
ssb: set_irq: core 0x0806, irq 4 => 4
ssb: set_irq: core 0x0806, irq 5 => 5
ssb: set_irq: core 0x0808, irq 6 => 2
ssb: set_irq: core 0x0804, irq 2 => 6
ssb: after irq reconfiguration
ssb: core 0x0800, irq : 2(S)  3* 4  5  6  D  I
ssb: core 0x0806, irq : 2(S)  3  4* 5  6  D  I
ssb: core 0x0806, irq : 2(S)  3  4  5* 6  D  I
ssb: core 0x0808, irq : 2(S)* 3  4  5  6  D  I
ssb: core 0x0804, irq : 2(S)  3  4  5  6* D  I
ssb: core 0x0816, irq : 2(S)* 3  4  5  6  D  I
ssb: core 0x0807, irq : 2(S)* 3  4  5  6  D  I
ssb: core 0x080b, irq : 2(S)* 3  4  5  6  D  I
ssb: core 0x080f, irq : 2(S)  3  4  5  6  D  I*
ssb: Sonics Silicon Backplane found at address 0x18000000
Serial init done.
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
  Normal   0x00000000 -> 0x00002000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00002000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
PID hash table entries: 128 (order: -3, 512 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
Memory: 29524k/32768k available (2322k kernel code, 3244k reserved, 357k data, 136k init, 0k highmem)
Hierarchical RCU implementation.
NR_IRQS:128
console [ttyS0] enabled
Calibrating delay loop... 263.16 BogoMIPS (lpj=526336)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
bio: create slab <bio-0> at 0
Switching to clocksource MIPS
ssb: PCIcore in host mode found
PCI: Fixing up bridge 0000:00:00.0
PCI: Fixing up device 0000:00:00.0
PCI: Fixing latency timer of device 0000:00:00.0 to 168
pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot
pci 0000:00:02.0: PME# disabled
pci 0000:00:02.1: PME# supported from D0 D1 D2 D3hot
pci 0000:00:02.1: PME# disabled
pci 0000:00:03.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:03.0: PME# disabled
pci 0000:00:03.0: BAR 8: can't allocate I/O resource [0x800-0x7ff]
pci 0000:00:03.0: CardBus bridge, secondary bus 0000:01
pci 0000:00:03.0:   IO window: 0x000400-0x0004ff
pci 0000:00:03.0:   PREFETCH window: 0x40000000-0x43ffffff
pci 0000:00:03.0:   MEM window: 0x44000000-0x47ffffff
PCI: Enabling device 0000:00:03.0 (0000 -> 0003)
PCI: Fixing up device 0000:00:03.0
PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
PCI: Fixing up device 0000:00:01.0
ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x0D, vendor 0x4243)
ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x09, vendor 0x4243)
ssb: Core 2 found: PCI (cc 0x804, rev 0x0C, vendor 0x4243)
ssb: Core 3 found: PCMCIA (cc 0x80D, rev 0x07, vendor 0x4243)
ssb: WARNING: Invalid SPROM CRC (corrupt SPROM)
ssb: Unsupported SPROM  revision 0 detected. Will extract v1
ssb: Sonics Silicon Backplane found on PCI device 0000:00:01.0
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
msgmni has been set to 57
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
serial8250: ttyS0 at MMIO 0xb8000300 (irq = 3) is a 16550A
serial8250: ttyS1 at MMIO 0xb8000400 (irq = 3) is a 16550A
serial8250.0: ttyS0 at MMIO 0xb8000300 (irq = 3) is a 16550A
serial8250.0: ttyS1 at MMIO 0xb8000400 (irq = 3) is a 16550A
flash init: 0x1c000000 0x02000000
Physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
Physically mapped flash: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Flash device: 0x1000000 at 0x1fc00000
bootloader size: 262144
Creating 4 MTD partitions on "Physically mapped flash":
0x000000000000-0x000000040000 : "cfe"
0x000000040000-0x000000fe0000 : "linux"
0x00000011a400-0x000000fe0000 : "rootfs"
mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=300000, len=CE0000
0x000000300000-0x000000fe0000 : "rootfs_data"
0x000000fe0000-0x000001000000 : "nvram"
b44.c:v2.0
eth0: Broadcom 44xx/47xx 10/100BaseT Ethernet 00:23:69:57:2f:0d
b44: eth1: PHY Reset would not complete.
eth1: Broadcom 44xx/47xx 10/100BaseT Ethernet 00:90:4c:60:00:2b
BCM47xx Watchdog Timer enabled (30 seconds, nowayout)
TCP westwood registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 136k freed
Please be patient, while OpenWrt loads ...
diag: Detected 'Linksys WRTSL54GS'
diag: Detected 'diag: Detected 'diag: Detected 'diag: [...]

bttyS0: 3 input overrun(s)
44: eth0: powerb44: eth0: Link b44: eth0: Flow b44: eth0: powerPress the [f] key and hit [enter] to enter failsafe mode



później już tylko sieczka hmm

Jakieś pomysły jak sonie z tym poradzić?

2 Odpowiedź przez rpc (edytowany przez rpc 2010-09-08 05:11:04)

  • rpc
  • Użytkownik
  • Nieaktywny
  • Skąd: Wolbórz
  • Zarejestrowany: 2009-11-02
  • Posty: 581

Odp: OpenWrt zwałka na wrt54g3gv2-vf

hehe cezary masz co analizować smile
@Zawisza: na drugi raz wrzuć tą sieczkę do pliku a nie na forum

Pozdrawiam
Rafał
http://rpc.one.pl
http://openrouter.info

rpc's Strona

3 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,068

Odp: OpenWrt zwałka na wrt54g3gv2-vf

Nie ma co analizować. Nie działa driver od ethernetu i jesteś pierwszy który to ma smile. Który konkretnie obraz wgrałeś?

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

4 Odpowiedź przez rpc

  • rpc
  • Użytkownik
  • Nieaktywny
  • Skąd: Wolbórz
  • Zarejestrowany: 2009-11-02
  • Posty: 581

Odp: OpenWrt zwałka na wrt54g3gv2-vf

chodziło mi o te sieczkę smile którą usunąłeś
@cezary: a czemu sterownik ethernetu blokuje możliwość dostępu poprzez RS ?

Pozdrawiam
Rafał
http://rpc.one.pl
http://openrouter.info

rpc's Strona

5 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,068

Odp: OpenWrt zwałka na wrt54g3gv2-vf

Ta sieczka powodowała niezłe zamulenie FF, chociaż na chromie chodziło.

Prawdopodnie przez to albo kernel całkowicie się przekręcił, albo lata w pętli i nie ma już czasu na obsługę rsa.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

6 Odpowiedź przez Zawisza

  • Zarejestrowany: 2010-09-07
  • Posty: 39

Odp: OpenWrt zwałka na wrt54g3gv2-vf

Cezary napisał/a:

Nie ma co analizować. Nie działa driver od ethernetu i jesteś pierwszy który to ma smile. Który konkretnie obraz wgrałeś?

Wgrałem openwrt-wrt54g3gv2-vf-squashfs.bin

7 Odpowiedź przez Zawisza

  • Zarejestrowany: 2010-09-07
  • Posty: 39

Odp: OpenWrt zwałka na wrt54g3gv2-vf

Cezary napisał/a:

Ta sieczka powodowała niezłe zamulenie FF, chociaż na chromie chodziło.

Prawdopodnie przez to albo kernel całkowicie się przekręcił, albo lata w pętli i nie ma już czasu na obsługę rsa.

Pytanie brzmi co dalej, zwłaszcza że przez RS'a na dzień dzisiejszy nie udało mi się podać jakiejkolwiek komendy a jedynie oglądam te komunikaty. Nie potrafię nawet przerwać tego bootowania.
Kabel wydaje się być ok choć nigdy nic nie wiadomo.

8 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,068

Odp: OpenWrt zwałka na wrt54g3gv2-vf

W broadcomie masz tftp. Zwykle możesz w ten sposób wgrać oryginał.

Co do openwrt - jak pisałem jesteś pierwszy który kto zgłosił. Jak bym wgrał oryginał, zresetował wszystko do domyślnych wartości i jeszcze raz wgrał openwrt.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

9 Odpowiedź przez Zawisza

  • Zarejestrowany: 2010-09-07
  • Posty: 39

Odp: OpenWrt zwałka na wrt54g3gv2-vf

Próbowałem wgrać oryginał  (http://www.linksysbycisco.com/ANZ/en/su … F/download) WRT54G3GV2-VFV2.0_3.00.24_006_ETSI_code.bin i niestety też zwałka sad
Logi podeślę wieczorową porą.

10 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,068

Odp: OpenWrt zwałka na wrt54g3gv2-vf

Wybacz, ale co jak co - oryginał musi chodzić...

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

11 Odpowiedź przez Zawisza

  • Zarejestrowany: 2010-09-07
  • Posty: 39

Odp: OpenWrt zwałka na wrt54g3gv2-vf

Cezary napisał/a:

Wybacz, ale co jak co - oryginał musi chodzić...

Sam zobacz: (nie bardzo wiem jak dodać ten log w postaci pliku, więc z góry przepraszam za sieczkę):

CFE version 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: Thu Aug  7 16:44:55 CST 2008 (root@localhost.localdomain)
Copyright (C) 2000,2001,2002,2003 Broadcom Corporation.

Initializing Arena
Initializing Devices.

No DPN
This is a Parallel Flash
Boot partition size = 262144(0x40000)
Try 4: vendor id = 0x0001, device id = 0x2201
Flash type is "S29GL128N10TFI010 8Mx16"
Total size is 0x1000000.
Block size is 0x20000.
Total blocks are 122. (Image 1 are 61(7995392), Image 2 is 61(7995392))
Partition information:
boot    #00   00000000 -> 0003FFFF  (262144)
trx     #01   00040000 -> 0004001F  (32)
os      #02   00040020 -> 007DFFFF  (7995360)
trx2    #03   007E0000 -> 007E001F  (32)
os2     #04   007E0020 -> 00F7FFFF  (7995360)
lang    #05   00F80000 -> 00FF7FFF  (491520)
nvram   #06   00FF8000 -> 00FFFFFF  (32768)
Partition information:
boot    #00   00000000 -> 0003FFFF  (262144)
trx     #01   00040000 -> 007DFFFF  (7995392)
trx2    #02   007E0000 -> 00F7FFFF  (7995392)
lang    #03   00F80000 -> 00FF7FFF  (491520)
nvram   #04   00FF8000 -> 00FFFFFF  (32768)
et0: Broadcom BCM47xx 10/100 Mbps Ethernet Controller 4.150.10.5
et1: Broadcom BCM47xx 10/100 Mbps Ethernet Controller 4.150.10.5
CPU type 0x29006: 264MHz
Total memory: 32768 Total memory used by CFE:  0x80700000 - 0x807A51F0 (676336)
Initialized Data:          0x8073B950 - 0x8073E9A0 (12368)
BSS Area:                  0x8073E9A0 - 0x8073F1F0 (2128)
Local Heap:                0x8073F1F0 - 0x807A31F0 (409600)
Stack Area:                0x807A31F0 - 0x807A51F0 (8192)
Text (code) segment:       0x80700000 - 0x8073B950 (244048)
Boot area (physical):      0x007A6000 - 0x007E6000
Relocation Factor:         I:00000000 - D:00000000

Boot version: v5.5
The boot is CFE

mac_init(): Find mac [00:23:69:57:2F:0D] in location 0
Nothing...
CMD: [ifconfig eth0 -addr=192.168.1.1 -mask=255.255.255.0]
Device eth0:  hwaddr 00-23-69-57-2F-0D, ipaddr 192.168.1.1, mask 255.255.255.0
        gateway not set, nameserver not set
CMD: [go;]
Check CRC of image1
  Len:     0xDA400    (893952)    (0xBC040000)
  Offset0: 0x20        (32)        (0xBC040020)
  Offset1: 0x978    (2424)    (0xBC040978)
  Offset2: 0xDA400    (893952)    (0xBC11A400)
  Offset3: 0x2A1D1C    (2759964)    (0xBC2E1D1C)
  Version: v3.0.24 #006
  Stable:  0xFF
  Try:     0x74, 0x74, 0x74
Try three time, and can't boot the image, maybe the image is bad. (Set skip_check_flag=1 to skip check.)
Check CRC of image2
Invalid boot block on disk
CMD: [flash -ctheader : flash1.trx]
Reading :: Failed.: Timeout occured
CMD: [flash -ctheader : flash1.trx]
Reading :: Failed.: Timeout occured
CMD: [flash -ctheader : flash1.trx]
Reading :: upgrade_ver[v3.0.24] upgrade_ver[30024] 4712_ver[0]
Done. 4314112 bytes read
fname=flash1.trx
CODE Pattern is correct! (3G2V)
Upgrade to image 1
Programming...done. 4314080 bytes written
Check CRC of image1
  Len:     0x41D000    (4313088)    (0xBC040000)
  Offset0: 0x20        (32)        (0xBC040020)
  Offset1: 0xA28    (2600)    (0xBC040A28)
  Offset2: 0xC4434    (803892)    (0xBC104434)
  Offset3: 0x41C434    (4310068)    (0xBC45C434)
  Version: v3.0.24 #006
  Stable:  0xFF
  Try:     0xFF, 0xFF, 0xFF
33 47 32 56 00 00 00 00 08 08 07 03 00 18 55 32 4E 44 00 06 1F 00 FF FF FF FF FF FF FF FF 00 00
Reset flag to 0xFF to avoid CRC error
33 47 32 56 00 00 00 00 08 08 07 03 00 18 55 32 4E 44 00 06 1F 00 FF FF FF FF FF FF FF FF 00 00
  Header CRC:    0x2B67070F
  Calculate CRC: 0x2B67070F
Image 1 is OK
Check CRC of image2
Invalid boot block on disk
Image Status : IMG2_BAD
Try to load image 1.
Change to load image 1.
Write 't' to 0x45C44C (0xBC45C44C)
Try 4: vendor id = 0x0001, device id = 0x2201
Flash type is "S29GL128N10TFI010 8Mx16"
Write 2 bytes from 45C44C to 45C44E
Write 2 bytes
CMD: [boot -raw -z -addr=0x80001000 -max=0xf40000 flash0.os:]
Loader:raw Filesys:raw Dev:flash0.os File: Options:(null)
Loading: .. 4216 bytes read
Entry at 0x80001000
Closing network.
Starting program at 0x80001000
CPU revision is: 00029006

Primary instruction cache 16kb, linesize 16 bytes (2 ways)

Primary data cache 16kb, linesize 16 bytes (2 ways)

Linux version 2.4.20 (root@localhost.localdomain) (gcc version 3.2.3 with Broadcom modifications) #15 Thu Aug 7 16:44:05 CST 2008

Setting the PFC to its default value

Determined physical RAM map:

memory: 02000000 @ 00000000 (usable)

On node 0 totalpages: 8192

zone(0): 8192 pages.

zone(1): 0 pages.

zone(2): 0 pages.

Kernel command line: root=/dev/mtdblock2 noinitrd console=ttyS0,115200

CPU: BCM4704 rev 9 at 264 MHz

Calibrating delay loop... 263.78 BogoMIPS

Memory: 29756k/32768k available (2176k kernel code, 3012k reserved, 128k data, 92k init, 0k highmem)

Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)

Inode cache hash table entries: 2048 (order: 2, 16384 bytes)

Mount-cache hash table entries: 512 (order: 0, 4096 bytes)

Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)

Page-cache hash table entries: 8192 (order: 3, 32768 bytes)

Checking for 'wait' instruction...  unavailable.

POSIX conformance testing by UNIFIX

PCI: Initializing host

PCI: Fixing up bus 0

PCI: Fixing up bridge

PCI: Fixing up bus 1

    pcibios_fixup_bus d->irq:c

PCI device 14e4:4318(01:01.0) res start=40002000,stop=40003fff

PCI device 14e4:4318(01:01.0) res start=0,stop=0

PCI device 14e4:4318(01:01.0) res start=0,stop=0

PCI device 14e4:4318(01:01.0) res start=0,stop=0

PCI device 14e4:4318(01:01.0) res start=0,stop=0

PCI device 14e4:4318(01:01.0) res start=0,stop=0

    pcibios_fixup_bus d->irq:c

PCI device 1033:0035(01:02.0) res start=40004000,stop=40004fff

PCI device 1033:0035(01:02.0) res start=0,stop=0

PCI device 1033:0035(01:02.0) res start=0,stop=0

PCI device 1033:0035(01:02.0) res start=0,stop=0

PCI device 1033:0035(01:02.0) res start=0,stop=0

PCI device 1033:0035(01:02.0) res start=0,stop=0

    pcibios_fixup_bus d->irq:c

PCI device 1033:00e0(01:02.1) res start=40005000,stop=400050ff

PCI device 1033:00e0(01:02.1) rt=0,stop=0

PCI device 1033:00e0(01:02.1) res start=0,stop=0

PCI device 1033:00e0(01:02.1) res start=0,stop=0

PCI device 1033:00e0(01:02.1) res start=0,stop=0

PCI device 1033:00e0(01:02.1) res start=0,stop=0

    pcibios_fixup_bus d->irq:c

PCI device 104c:ac56(01:03.0) res start=40006000,stop=40006fff

PCI device 104c:ac56(01:03.0) res start=0,stop=0

PCI device 104c:ac56(01:03.0) res start=0,stop=0

PCI device 104c:ac56(01:03.0) res start=0,stop=0

PCI device 104c:ac56(01:03.0) res start=0,stop=0

PCI device 104c:ac56(01:03.0) res start=0,stop=0

    pcibios_fixup_bus d->irq:c

Linux NET4.0 for Linux 2.4

Based upon Swansea University Computer Society NET3.039

Initializing RT netlink socket

Starting kswapd

devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)

devfs: boot_options: 0x1

NTFS driver v1.1.22 [Flags: R/O]

squashfs: version 3.0 (2006/03/15) Phillip Lougher

JFFS2 version 2.1. (C) 2001 Red Hat, Inc., designed by Axis Communications AB.

pty: 256 Unix98 ptys configured

Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled

ttyS00 at 0xb8000300 (irq = 3) is a 16550A

ttyS01 at 0xb8000400 (irq = 0) is a 16550A

HDLC line discipline: version $Revision: 1.1.1.4 $, maxframe=4096

N_HDLC line discipline registered.

Uniform Multi-Platform E-IDE driver Revision: 6.31

ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx

ide0: ports already in use, skipping probe

ide1: ports already in use, skipping probe

ide2: ports already in use, skipping probe

ide3: ports already in use, skipping probe

ide4: ports already in use, skipping probe

ide5: ports already in use, skipping probe

PPP generic driver version 2.4.2

SCSI subsystem driver Revision: 1.00

scsi0 : SCSI host adapter emulation for IDE ATAPI devices

Amd/Fujitsu Extended Query Table v1.3 at 0x0040

number of CFI chips: 1

Flash device: 0x1000000 at 0x1c000000

Total blocks are 122. (image 1 are 61(7995392), image 2 is 61(7995392))

Find first TRX header at 0x40000, the rootfs is at 0xC4434

Creating 7 MTD partitions on "Physically mapped flash":

0x00000000-0x00040000 : "pmon"

0x00040000-0x007e0000 : "linux"

0x00104434-0x007e0000 : "rootfs"

mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-only

0x007e0000-0x00f80000 : "linux2"

0x007dffff-0x00f80000 : "rootfs2"

mtd: partition "rootfs2" doesn't start on an erase block boundary -- force read-only

0x00f80000-0x00fe0000 : "lang"

0x00fe0000-0x01000000 : "nvram"

sflash: found no supported devices

Linux Kernel Card Services 3.1.22

  options:  [pci] [cardbus]

    pcibios_enable_device() enter pcibios_enable_resources

PCI: Enabling device 01:03.0 (0000 -> 0002)

     yenta_allocate for type=1200 bus=PCI CardBus #02 offset=1c res->start=0

     yenta_allocate for type=1200 bus=PCI CardBus #02 offset=1c res->end=0

     yenta_allocate for type=200 bus=PCI CardBus #02 offset=24 res->start=40008000

     yenta_allocate for type=200 bus=PCI CardBus #02 offset=24 res->end=4000bfff

     yenta_allocate for type=100 bus=PCI CardBus #02 offset=2c res->start=0

     yenta_allocate for type=100 bus=PCI CardBus #02 offset=2c res->end=0

     yenta_allocate for type=100 bus=PCI CardBus #02 offset=34 res->start=0

     yenta_allocate for type=100 bus=PCI CardBus #02 offset=34 res->end=0

    yenta_open socket->cb_irq = dev->irq=c

    yenta_open socket->socket->base=c0070000

usb.c: registered new driver usbdevfs

usb.c: registered new driver hub

Yenta IRQ list 0000, PCI irq12

Socket status: 30000087

    yenta_config_init 04h=7:40h=0:42h=0:44h=3e1:80h=8405061:8ch=1002:90h=c0:91h=82:92h=64:93h=60:a2h=fe12:00h=ac56104c

    yenta_config_init 3ch=c:3dh=1:3eh=141

    yenta_config_init 805h=0

    yenta.c socket->io_irq=0

    pcibios_enable_device() enter pcibios_enable_resources

PCI: Enabling device 01:02.1 (0000 -> 0002)

ehci_hcd 01:02.1: PCI device 1033:00e0

ehci_hcd 01:02.1: irq 12, pci mem c0072000

usb.c: new USB bus registered, assigned bus number 1

ECHI PCI device e01033 found.

PCI: 01:02.1 PCI cache line size set incorrectly (0 bytes) by BIOS/FW, correcting to 32

ehci_hcd 01:02.1: USB 2.0 enabled, EHCI 1.00, driver 2003-Dec-29/2.4

hub.c: USB hub found

hub.c: 3 ports detected

host/usb-uhci.c: $Revision: 1.2.18.2 $ time 16:44:16 Aug  7 2008

host/usb-uhci.c: High bandwidth mode enabled

host/usb-uhci.c: v1.275:USB Universal Host Controller Interface driver

usb-ohci.c: USB OHCI at membase 0xb8003000, IRQ 6

usb-ohci.c: usb-00:03.0, PCI device 14e4:4715

usb.c: new USB bus registered, assigned bus number 2

hub.c: USB hub found

hub.c: 2 ports detected

    pcibios_enable_device() enter pcibios_enable_resources

PCI: Enabling device 01:02.0 (0000 -> 0002)

usb-ohci.c: USB OHCI at membase 0xc0074000, IRQ 12

usb-ohci.c: usb-01:02.0, PCI device 1033:0035

usb.c: new USB bus registered, assigned bus number 3

hub.c: USB hub found

hub.c: 3 ports detected

usb.c: registered new driver usblp

printer.c: v0.13: USB Printer Device Class driver

Initializing USB Mass Storage driver...

usb.c: registered new driver usb-storage

USB Mass Storage support registered.

NET4: Linux TCP/IP 1.0 for NET4.0

IP Protocols: ICMP, UDP, TCP, IGMP

IP: routing cache hash table of 512 buckets, 4Kbytes

TCP: Hash tables configured (established 2048 bind 4096)

Linux IP multicast router 0.06 plus PIM-SM

ip_conntrack version 2.1 (256 buckets, 2048 max) - 368 bytes per conntrack

Register conntrack protocol helper for ESP...

init IP_nat_proto_esp register.

IPSEC isakmp Support Max Pass-through [50].

ip_conntrack_rtsp v0.01 loading

ip_nat_rtsp v0.01 loading

ip_tables: (C) 2000-2002 Netfilter core team

ipt_time loading

NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.

NET4: Ethernet Bridge 008 for NET4.0

802.1Q VLAN Support v1.7 Ben Greear <greearb@candelatech.com>

All bugs added by David S. Miller <davem@redhat.com>

FAT: bogus logical sector size 13824

NTFS: Unable to set blocksize 512.

VFS: Mounted root (squashfs filesystem) readonly.

Mounted devfs on /dev

Freeing unused kernel memory: 92k freed

Algorithmics/MIPS FPU Emulator v1.5

Algorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPAlgorithmics/MIPfind "lang" in MSQUASHFS error: Can't find a SQUASTD 5 (/dev/mtdblock/5)
Algorithmics/MIPfind "laHFS superblock on mtdblock(31,5)

ret = -1
www -> /www
tts/0: 1 input overrun(s)

ng" in MSQUASHFSTD 5 (/dev/mtdblock/5)

Algorithmics/MIPfind "laHFS superblock on mtdblock(31,5)

ret = -1

www -> /www

tts/0: 1 input ong" imount: Invalid argument
Language Package: EN
modules[0]=et buf=[et ]
Language Package: EN

modules[1]=ctmisc buf=[et ctmisc ]
modules[2]=wl buf=[et ctmisc wl ]
Needed modules: et ctmisc wl
cmd=[insmod et ]
modules[0]=et buf=[et ]

12 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,068

Odp: OpenWrt zwałka na wrt54g3gv2-vf

Chodziło mi o to ze oryginał musi chodzić. A tu wygląda tak jak by Ci flash w routerze poleciał.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

13 Odpowiedź przez Zawisza

  • Zarejestrowany: 2010-09-07
  • Posty: 39

Odp: OpenWrt zwałka na wrt54g3gv2-vf

No teraz go już chyba dobiłem neutral, teraz to już nawet tftp nie działa, zobaczcie sami. Da radę coś z tym jeszcze zrobić czy szukać nowego.

CFE version 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: Thu Aug  7 16:44:55 CST 2008 (root@localhost.localdomain)
Copyright (C) 2000,2001,2002,2003 Broadcom Corporation.

Initializing Arena
Initializing Devices.

No DPN
This is a Parallel Flash
Boot partition size = 262144(0x40000)
Try 4: vendor id = 0x0001, device id = 0x2201
Flash type is "S29GL128N10TFI010 8Mx16"
Total size is 0x1000000.
Block size is 0x20000.
Total blocks are 122. (Image 1 are 61(7995392), Image 2 is 61(7995392))
Partition information:
boot    #00   00000000 -> 0003FFFF  (262144)
trx     #01   00040000 -> 0004001F  (32)
os      #02   00040020 -> 007DFFFF  (7995360)
trx2    #03   007E0000 -> 007E001F  (32)
os2     #04   007E0020 -> 00F7FFFF  (7995360)
lang    #05   00F80000 -> 00FF7FFF  (491520)
nvram   #06   00FF8000 -> 00FFFFFF  (32768)
Partition information:
boot    #00   00000000 -> 0003FFFF  (262144)
trx     #01   00040000 -> 007DFFFF  (7995392)
trx2    #02   007E0000 -> 00F7FFFF  (7995392)
lang    #03   00F80000 -> 00FF7FFF  (491520)
nvram   #04   00FF8000 -> 00FFFFFF  (32768)
et0: Broadcom BCM47xx 10/100 Mbps Ethernet Controller 4.150.10.5
et1: Broadcom BCM47xx 10/100 Mbps Ethernet Controller 4.150.10.5
CPU type 0x29006: 264MHz
Total memory: 32768 KBytes

Total memory used by CFE:  0x80700000 - 0x807A51F0 (676336)
Initialized Data:          0x8073B950 - 0x8073E9A0 (12368)
BSS Area:                  0x8073E9A0 - 0x8073F1F0 (2128)
Local Heap:                0x8073F1F0 - 0x807A31F0 (409600)
Stack Area:                0x807A31F0 - 0x807A51F0 (8192)
Text (code) segment:       0x80700000 - 0x8073B950 (244048)
Boot area (physical):      0x007A6000 - 0x007E6000
Relocation Factor:         I:00000000 - D:00000000

Boot version: v5.5
The boot is CFE

mac_init(): Find mac [00:23:69:57:2F:0D] in location 0
Nothing...
CMD: [ifconfig eth0 -addr=192.168.1.1 -mask=255.255.255.0]
Device eth0:  hwaddr 00-23-69-57-2F-0D, ipaddr 192.168.1.1, mask 255.255.255.0
        gateway not set, nameserver not set
CMD: [go;]
Check CRC of image1
  Len:     0xD9400    (889856)    (0xBC040000)
  Offset0: 0x20        (32)        (0xBC040020)
  Offset1: 0x978    (2424)    (0xBC040978)
  Offset2: 0xD9400    (889856)    (0xBC119400)
  Offset3: 0x249648    (2397768)    (0xBC289648)
  Version: v3.0.24 #006
  Stable:  0x73
  Try:     0x74, 0xFF, 0xFF
  Header CRC:    0x990CBEE7
  Calculate CRC: 0x990CBEE7
Image 1 is OK
Check CRC of image2
  Len:     0x271000    (2560000)    (0xBC7E0000)
  Offset0: 0x20        (32)        (0xBC7E0020)
  Offset1: 0x978    (2424)    (0xBC7E0978)
  Offset2: 0xD9400    (889856)    (0xBC8B9400)
  Offset3: 0x249648    (2397768)    (0xBCA29648)
  Version: v3.0.24 #006
  Stable:  0xFF
  Try:     0xFF, 0xFF, 0xFF
33 47 32 56 00 00 00 00 0A 09 0A 03 00 18 55 32 4E 44 00 06 00 00 FF FF FF FF FF FF FF FF 00 00
Reset flag to 0xFF to avoid CRC error
33 47 32 56 00 00 00 00 0A 09 0A 03 00 18 55 32 4E 44 00 06 00 00 FF FF FF FF FF FF FF FF 00 00
  Header CRC:    0xC4417C54
  Calculate CRC: 0xC4417C54
Image 2 is OK
Image Status : IMG_SAME
Try to load image 1.
Change to load image 1.
CMD: [boot -raw -z -addr=0x80001000 -max=0xf40000 flash0.os:]
Loader:raw Filesys:raw Dev:flash0.os File: Options:(null)
Loading: .. 4092 bytes read
Entry at 0x80001000
Closing network.
Starting program at 0x80001000
Linux version 2.6.34.5 (buildslave@dd.das-iro.de) (gcc version 4.3.3 (GCC) ) #1 Fri Sep 10 18:15:26 CEST 2010
CPU revision is: 00029006 (Broadcom BCM3302)
ssb: Sonics Silicon Backplane found at address 0x18000000
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
  Normal   0x00000000 -> 0x00002000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00002000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
Kernel command line:  root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
PID hash table entries: 128 (order: -3, 512 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
Memory: 29532k/32768k available (2320k kernel code, 3236k reserved, 338k data, 148k init, 0k highmem)
NR_IRQS:128
console [ttyS0] enabled
Calibrating delay loop... 263.16 BogoMIPS (lpj=526336)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
bio: create slab <bio-0> at 0
Switching to clocksource MIPS
PCI: Fixing up bridge 0000:00:00.0
PCI: Fixing up device 0000:00:00.0
PCI: Fixing latency timer of device 0000:00:00.0 to 168
pci 0000:00:03.0: BAR 9: assigned [mem 0x40000000-0x43ffffff pref]
pci 0000:00:03.0: BAR 10: assigned [mem 0x44000000-0x47ffffff]
pci 0000:00:01.0: BAR 0: assigned [mem 0x48000000-0x48001fff]
pci 0000:00:01.0: BAR 0: set to [mem 0x48000000-0x48001fff] (PCI address [0x48000000-0x48001fff]
pci 0000:00:02.0: BAR 0: assigned [mem 0x48002000-0x48002fff]
pci 0000:00:02.0: BAR 0: set to [mem 0x48002000-0x48002fff] (PCI address [0x48002000-0x48002fff]
pci 0000:00:03.0: BAR 0: assigned [mem 0x48003000-0x48003fff]
pci 0000:00:03.0: BAR 0: set to [mem 0x48003000-0x48003fff] (PCI address [0x48003000-0x48003fff]
pci 0000:00:02.1: BAR 0: assigned [mem 0x48004000-0x480040ff]
pci 0000:00:02.1: BAR 0: set to [mem 0x48004000-0x480040ff] (PCI address [0x48004000-0x480040ff]
pci 0000:00:03.0: BAR 7: assigned [io  0x0400-0x04ff]
pci 0000:00:03.0: BAR 8: can't assign io (size 0x100)
pci 0000:00:03.0: CardBus bridge to [bus 01-04]
pci 0000:00:03.0:   bridge window [io  0x0400-0x04ff]
pci 0000:00:03.0:   bridge window [mem 0x40000000-0x43ffffff pref]
pci 0000:00:03.0:   bridge window [mem 0x44000000-0x47ffffff]
PCI: Enabling device 0000:00:03.0 (0000 -> 0003)
PCI: Fixing up device 0000:00:03.0
PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
PCI: Fixing up device 0000:00:01.0
ssb: WARNING: Invalid SPROM CRC (corrupt SPROM)
ssb: Unsupported SPROM  revision 0 detected. Will extract v1
ssb: Sonics Silicon Backplane found on PCI device 0000:00:01.0
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
init_vdso successfull
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
msgmni has been set to 57
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
serial8250: ttyS0 at MMIO 0xb8000300 (irq = 3) is a 16550A
serial8250: ttyS1 at MMIO 0xb8000400 (irq = 3) is a 16550A
serial8250.0: ttyS0 at MMIO 0xb8000300 (irq = 3) is a 16550A
serial8250.0: ttyS1 at MMIO 0xb8000400 (irq = 3) is a 16550A
flash init: 0x1c000000 0x02000000
Physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
CFI mfr 0x00000001
CFI id  0x00002101
Amd/Fujitsu Extended Query Table at 0x0040
  Amd/Fujitsu Extended Query version 1.3.
Physically mapped flash: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
Flash device: 0x1000000 at 0x1fc00000
bootloader size: 262144
Looking for dual image
dual image TRX header found
Creating 4 MTD partitions on "Physically mapped flash":
0x000000000000-0x000000040000 : "cfe"
0x000000040000-0x0000007e0000 : "linux"
0x000000119400-0x0000007e0000 : "rootfs"
mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=2A0000, len=540000
0x0000002a0000-0x0000007e0000 : "rootfs_data"
0x000000fe0000-0x000001000000 : "nvram"
b44: b44.c:v2.0
b44 ssb0:0: eth0: Broadcom 44xx/47xx 10/100BaseT Ethernet 00:23:69:57:2f:0d
b44 ssb0:1: eth1: PHY Reset would not complete
b44 ssb0:1: eth1: Broadcom 44xx/47xx 10/100BaseT Ethernet 00:90:4c:60:00:2b
BCM47xx Watchdog Timer enabled (30 seconds, nowayout)
TCP westwood registered
NET: Registered protocol family 17
Bridge firewalling registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 148k freed
VFS: Mounted rooFreeing unused kVFS: Mounted rooFreeing unused kVFS: Mounted rooFre

itd. dziwne znaczki a na końcu:

- regular preinit -

switching to jffs2
mini_fo: using base directory: /
mini_fo: using storage directory: /overlay
- init -
Kernel panic - not syncing: Attempted to kill init!

14 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,068

Odp: OpenWrt zwałka na wrt54g3gv2-vf

Kernel sie wywalił. Przed tym każe nacisnąć f (lub dowolny przycisk) - wtedy może wejść w failsafe i nie zamontować jffs. Być może wtedy dało by się go całkowicie wyczyścić i wgrać od nowa coś.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

15 Odpowiedź przez Zawisza

  • Zarejestrowany: 2010-09-07
  • Posty: 39

Odp: OpenWrt zwałka na wrt54g3gv2-vf

Cezary napisał/a:

Kernel sie wywalił. Przed tym każe nacisnąć f (lub dowolny przycisk) - wtedy może wejść w failsafe i nie zamontować jffs. Być może wtedy dało by się go całkowicie wyczyścić i wgrać od nowa coś.

Nie wiem tylko dlaczego nie przyjmuje moich komend. Nic jak gdyby nadawnie po RSie nie szło. Kabelek przygotowałem zgodnie z http://wiki.openwrt.org/toh/linksys/wrt54g3gv2-vf i skoro wyświetla to powinno być OK. Jako programu używam putty.

16 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,068

Odp: OpenWrt zwałka na wrt54g3gv2-vf

Żeby przyjmował komendy musi działać. Jak kernel nie działa, to nie będzie odpowiadał. Podczas uruchamiania możesz sprawdzić czy ctrl-c zadziała - być może przerwie bootloader (cfe)

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

17 Odpowiedź przez Zawisza

  • Zarejestrowany: 2010-09-07
  • Posty: 39

Odp: OpenWrt zwałka na wrt54g3gv2-vf

Chyba ten kabelek nie działa właściwie.
Ok. to zrobie ten kabel jeszcze raz. Potwierdźcie proszę tylko gdzie na wtyk DB9 (klasyk RS232) doprowadzić ten pin  z zasilaniem +3,5V (http://wiki.openwrt.org/toh/linksys/wrt54g3gv2-vf). Z pozostałymi to raczej nie ma problemu.
Jak pierwszy kabelek zrobiłem z to był z Noki DLR-3P RED (+3.3V), GREEN RXD), GRAY (TXD)  BLACK+SHIELD (GND) i nie bardzo wiedziałem gdzie ten czerwony śmiga. Teraz robię całość samodzielnie i nie wiem co z tym +3,5V

18 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,068

Odp: OpenWrt zwałka na wrt54g3gv2-vf

Nigdzie. Chyba że do konwertera, jeżeli nie ma on osobnego zasilania z rs'a.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

19 Odpowiedź przez Zawisza

  • Zarejestrowany: 2010-09-07
  • Posty: 39

Odp: OpenWrt zwałka na wrt54g3gv2-vf

Szukam osoby która mogłaby mi pomóc w reanimacji mojego wrt54g3gv2-vf (także odpłatnie, Warszawa)

20 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,068

Odp: OpenWrt zwałka na wrt54g3gv2-vf

Znalazłeś. Ale tego w/w? Jak to flash to nie wiem czy coś z niego będzie...

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

21 Odpowiedź przez Zawisza

  • Zarejestrowany: 2010-09-07
  • Posty: 39

Odp: OpenWrt zwałka na wrt54g3gv2-vf

Cezary napisał/a:

Znalazłeś. Ale tego w/w? Jak to flash to nie wiem czy coś z niego będzie...

Info podesłałem na email