Nie jesteś zalogowany. Proszę się zalogować lub zarejestrować.
eko.one.pl → Oprogramowanie / Software → Witam, najlepszych :) Dobór Ruterka..
Strony Poprzednia 1 … 9 10 11 12 13 … 16 Następna
Zaloguj się lub zarejestruj by napisać odpowiedź
Ale gargoyle to juz pewnie nie?
A inne pytanie: Ze strony http://www.netgear.pl/home/products/wir … fault.aspx cos podejdzie?
Bo masz już sterowniki zainstalowane
, Tak ma być.
Super, możesz sprawdzić czy all się zgadza jestem przed ostatnim etapem czyli konfiguracji wan, zobacz czy do tej pory jest all ok jeśli możesz i znajdziesz chwilę
root@Gargoyle:~# cat /proc/bus/usb/devices
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 1
B: Alloc= 1/800 us ( 0%), #Int= 2, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0002 Rev= 3.03
S: Manufacturer=Linux 3.3.8 ehci_hcd
S: Product=Generic Platform EHCI Controller
S: SerialNumber=ehci-platform
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 4
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=05e3 ProdID=0608 Rev=77.64
S: Product=USB2.0 Hub
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 1 Ivl=256ms
T: Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#= 4 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=12d1 ProdID=1436 Rev= 0.00
S: Manufacturer=HUAWEI Technology
S: Product=HUAWEI Mobile
C:* #Ifs= 7 Cfg#= 1 Atr=e0 MxPwr=500mA
A: FirstIf#= 1 IfCount= 2 Cls=02(comm.) Sub=00 Prot=00
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 1 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=ff Driver=cdc_ether
E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 5 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 6 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0msobecnie wan wygląda tak:
config interface 'wan'
option auto '1'
option proto '3g'
option device '/dev/ttyUSB0'
option apn 'internet'
option service 'umts'
option mobile_isp 'custom'i mam zmodyfikować na:
config 'interface' 'wan'
option 'auto' '0'
option 'proto' 'dhcp'
option ifname usb0
option macaddr 00:01:02:03:04:05zgadza się?
Tylko powiedz jeszcze gdzie to wpisujemy:
Nawiązanie połączenia
Wystarczy wydać polecenie
AT^NDISDUP=1,1,"darmowy"@badziewiak: to jest brcm47xxx...
@Kusiu: przeszukaj forum. Albo picocomem albo ręcznie przez gcom, albo masz mój gotowy skrypt na forum który to robi.
tak jak myślałem, robię wszystko według poradnika na eko, po tym zabiegu daje reset i nie łączy się z modemem dopiero ustawienie w garygoyle z dhcp na 3g/lte łączy ponownie. Poradnik: http://eko.one.pl/?p=openwrt-ndis
Obecne ustawienia wan:
config interface 'wan'
option auto '1'
option proto '3g'
option device '/dev/ttyUSB0'
option apn 'internet'
option service 'umts'
option mobile_isp 'custom'po tym zabiegu:
config 'interface' 'wan'
option 'auto' '0'
option 'proto' 'dhcp'
option ifname usb0
option macaddr 00:01:02:03:04:05nie łączy nie dawałem tylko tych myslnikow do
'interface, auto i proto może to mieć jakieś znaczenie?
Pozdrawiam
skrypt wyglądał tak:
# Put your custom commands here that should be executed once
# the system init finished. By default this file does nothing.
sleep 5
MODE="AT^NDISDUP=1,1,\"internet\"" gcom -d /dev/ttyUSB2 -s /etc/gcom/setmode.gco
ifup wan
(while true; do ping wp.pl > /dev/null; sleep 1; done) &
exit 0
~
~
~
~
~
~
~
~
~
~
~
~
~
~
~
~
- /etc/rc.local 1/7 14%Jeśli usuwam jakieś linie jak niżej jak usunąć tą wolną przestrzeń:
# Put your custom commands here that should be executed once
# the system init finished. By default this file does nothing.
(while true; do ping wp.pl > /dev/null; sleep 1; done) &
exit 0
~
~
~
~
~
~
~
~
~
~
~
~
~
~
~
~
- /etc/rc.local 1/7 14%Jeżeli uci show network nie pokazuje błędów to nie ma znacznia. Jaki modem? I czy na pewno masz usb0 a nie wwan0 (od wersji kernela zależy).
Jeżeli uci show network nie pokazuje błędów to nie ma znacznia. Jaki modem? I czy na pewno masz usb0 a nie wwan0 (od wersji kernela zależy).
nie wiem czy to ma znaczenie ale w gui mi pisze po wroceniu do wczesniejszych ustawien "/dev/ttyUSB0" e173u-2
Jakie znów gui jak ręcznie to konfigurujesz? Napisałem co masz zrobić, zrób i zobacz.
Jest coś nie tak, załączam konfiguracje i logi, nie łączy w ogóle modemu.
config interface 'wan'
option auto '0'
option proto 'dhcp'
option ifname wwan0
option macaddr 00:01:02:03:04:05
------------------------------------------------------------------------------------------------------------------------------
Jun 8 13:48:38 Gargoyle user.info sysinit: Loading defaults
Jun 8 13:48:38 Gargoyle user.notice usb-modeswitch: 1-1:1.0: Manufacturer=? Product=USB2.0_Hub Serial=?
Jun 8 13:48:38 Gargoyle user.info sysinit: Loading synflood protection
Jun 8 13:48:39 Gargoyle user.info sysinit: Adding custom chains
Jun 8 13:48:39 Gargoyle user.notice usb-modeswitch: 1-1.1:1.0: Manufacturer=HUAWEI_Technology Product=HUAWEI_Mobile Serial=?
Jun 8 13:48:39 Gargoyle user.notice usb-modeswitch: 1-1.1:1.0: Selecting /etc/usb_modeswitch.d/12d1:1446 for mode switching
Jun 8 13:48:39 Gargoyle syslog.notice usb_modeswitch: switching device 12d1:1446 on 001/003
Jun 8 13:48:39 Gargoyle kern.info kernel: [ 55.560000] usb 1-1.1: USB disconnect, device number 3
Jun 8 13:48:39 Gargoyle user.info sysinit: Loading zones
Jun 8 13:48:40 Gargoyle user.info sysinit: Loading forwardings
Jun 8 13:48:40 Gargoyle user.info sysinit: Loading rules
Jun 8 13:48:40 Gargoyle user.info sysinit: Loading redirects
Jun 8 13:48:40 Gargoyle user.info sysinit: Loading includes
Jun 8 13:48:41 Gargoyle user.info sysinit: Optimizing conntrack
Jun 8 13:48:41 Gargoyle user.info sysinit: Loading interfaces
Jun 8 13:48:41 Gargoyle user.info firewall: adding lan (br-lan) to zone lan
Jun 8 13:48:42 Gargoyle authpriv.info dropbear[1716]: Running in background
Jun 8 13:48:43 Gargoyle daemon.warn httpd_gargoyle[1743]: started as root without requesting chroot(), warning only
Jun 8 13:48:43 Gargoyle daemon.notice httpd_gargoyle[1743]: httpd_gargoyle/1.0 14mar2008 starting on Gargoyle, port 80
Jun 8 13:48:43 Gargoyle kern.info kernel: [ 59.700000] usb 1-1.1: new high-speed USB device number 4 using ehci-platform
Jun 8 13:48:44 Gargoyle kern.info kernel: [ 59.820000] option 1-1.1:1.0: GSM modem (1-port) converter detected
Jun 8 13:48:44 Gargoyle kern.info kernel: [ 59.820000] usb 1-1.1: GSM modem (1-port) converter now attached to ttyUSB0
Jun 8 13:48:44 Gargoyle kern.info kernel: [ 59.830000] cdc_ether 1-1.1:1.1: wwan0: register 'cdc_ether' at usb-ehci-platform-1.1, Mobile Broadband Network Device, 02:50:f3:00:00:00
Jun 8 13:48:44 Gargoyle kern.info kernel: [ 59.880000] option 1-1.1:1.3: GSM modem (1-port) converter detected
Jun 8 13:48:44 Gargoyle kern.info kernel: [ 59.880000] usb 1-1.1: GSM modem (1-port) converter now attached to ttyUSB1
Jun 8 13:48:44 Gargoyle kern.info kernel: [ 59.940000] option 1-1.1:1.4: GSM modem (1-port) converter detected
Jun 8 13:48:44 Gargoyle kern.info kernel: [ 59.940000] usb 1-1.1: GSM modem (1-port) converter now attached to ttyUSB2
Jun 8 13:48:44 Gargoyle kern.info kernel: [ 59.950000] scsi6 : usb-storage 1-1.1:1.5
Jun 8 13:48:44 Gargoyle kern.info kernel: [ 59.970000] scsi7 : usb-storage 1-1.1:1.6
Jun 8 13:48:44 Gargoyle user.notice dnsmasq: DNS rebinding protection is active, will discard upstream RFC1918 responses!
Jun 8 13:48:44 Gargoyle user.notice dnsmasq: Allowing 127.0.0.0/8 responses
Jun 8 13:48:45 Gargoyle kern.notice kernel: [ 61.040000] scsi 6:0:0:0: CD-ROM HUAWEI Mass Storage 2.31 PQ: 0 ANSI: 2
Jun 8 13:48:45 Gargoyle kern.notice kernel: [ 61.050000] scsi 7:0:0:0: Direct-Access HUAWEI SD Storage 2.31 PQ: 0 ANSI: 2
Jun 8 13:48:45 Gargoyle kern.notice kernel: [ 61.080000] sd 7:0:0:0: [sda] Attached SCSI removable disk
Jun 8 13:48:48 Gargoyle daemon.info dnsmasq[1930]: started, version 2.62 cachesize 150
Jun 8 13:48:48 Gargoyle daemon.info dnsmasq[1930]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack
Jun 8 13:48:48 Gargoyle daemon.info dnsmasq-dhcp[1930]: DHCP, IP range 192.168.1.100 -- 192.168.1.249, lease time 12h
Jun 8 13:48:48 Gargoyle daemon.info dnsmasq[1930]: using local addresses only for domain lan
Jun 8 13:48:48 Gargoyle daemon.info dnsmasq[1930]: reading /tmp/resolv.conf.auto
Jun 8 13:48:48 Gargoyle daemon.warn dnsmasq[1930]: ignoring nameserver 192.168.1.1 - local interface
Jun 8 13:48:48 Gargoyle daemon.info dnsmasq[1930]: using local addresses only for domain lan
Jun 8 13:48:48 Gargoyle daemon.info dnsmasq[1930]: read /etc/hosts - 2 addresses
Jun 8 13:48:48 Gargoyle daemon.info dnsmasq-dhcp[1930]: read /etc/ethers - 0 addresses
Jun 8 13:48:48 Gargoyle user.err syslog: error starting threads: errno 89 (Function not implemented)
Jun 8 13:48:48 Gargoyle user.info sysinit: exportfs: could not open /var/lib/nfs/.etab.lock for locking: errno 2 (No such file or directory)
Jun 8 13:48:48 Gargoyle user.info sysinit: exportfs: can't lock /var/lib/nfs/etab for writing
Jun 8 13:48:48 Gargoyle user.info sysinit: exportfs: could not open /var/lib/nfs/.xtab.lock for locking: errno 2 (No such file or directory)
Jun 8 13:48:48 Gargoyle user.info sysinit: exportfs: can't lock /var/lib/nfs/xtab for writing
Jun 8 13:48:50 Gargoyle user.info sysinit: ERROR: No valid dynamic DNS service configurations defined
Jun 8 13:48:50 Gargoyle user.info sysinit: (Did you specify correct configuration file path?)
Jun 8 13:48:50 Gargoyle daemon.info hostapd: wlan0: STA 00:26:82:a0:a6:88 IEEE 802.11: authenticated
Jun 8 13:48:50 Gargoyle daemon.info hostapd: wlan0: STA 00:26:82:a0:a6:88 IEEE 802.11: associated (aid 1)
Jun 8 13:48:50 Gargoyle daemon.info hostapd: wlan0: STA 00:26:82:a0:a6:88 WPA: pairwise key handshake completed (RSN)
Jun 8 13:48:50 Gargoyle daemon.info dnsmasq-dhcp[1930]: DHCPREQUEST(br-lan) 192.168.1.191 00:26:82:a0:a6:88
Jun 8 13:48:50 Gargoyle daemon.info dnsmasq-dhcp[1930]: DHCPACK(br-lan) 192.168.1.191 00:26:82:a0:a6:88 Justyna-Justyna
Jun 8 13:48:55 Gargoyle daemon.info dnsmasq-dhcp[1930]: DHCPINFORM(br-lan) 192.168.1.190 90:fb:a6:a6:7a:28
Jun 8 13:48:55 Gargoyle daemon.info dnsmasq-dhcp[1930]: DHCPACK(br-lan) 192.168.1.190 90:fb:a6:a6:7a:28 Justyna-Justyna
Jun 8 13:48:55 Gargoyle daemon.info dnsmasq-dhcp[1930]: DHCPINFORM(br-lan) 192.168.1.191 00:26:82:a0:a6:88
Jun 8 13:48:55 Gargoyle daemon.info dnsmasq-dhcp[1930]: DHCPACK(br-lan) 192.168.1.191 00:26:82:a0:a6:88 Justyna-Justyna
Jun 8 13:48:57 Gargoyle user.notice ifup: Enabling Router Solicitations on loopback (lo)
Jun 8 13:49:10 Gargoyle user.notice usb-modeswitch: 1-1.1:1.1: Manufacturer=HUAWEI_Technology Product=HUAWEI_Mobile Serial=?
Jun 8 13:49:15 Gargoyle user.notice root: vsftpd init: mounted = 0
Jun 8 13:49:15 Gargoyle user.info sysinit: ERROR: No drives attached, no directories to share!
Jun 8 13:49:20 Gargoyle user.info sysinit: Can't open device /dev/ttyUSB2.
Jun 8 13:49:21 Gargoyle user.info sysinit: ping: bad address 'wp.pl'
Jun 8 13:49:21 Gargoyle daemon.notice netifd: wan (2925): udhcpc (v1.19.4) started
Jun 8 13:49:21 Gargoyle user.info sysinit: setting up led USB1
Jun 8 13:49:21 Gargoyle user.info sysinit: setting up led USB2
Jun 8 13:49:21 Gargoyle user.info sysinit: setting up led WLAN2G
Jun 8 13:49:21 Gargoyle daemon.notice netifd: wan (2925): Sending discover...
Jun 8 13:49:22 Gargoyle user.info sysinit: ping: bad address 'wp.pl'
Jun 8 13:49:23 Gargoyle user.info sysinit: ping: bad address 'wp.pl'
Jun 8 13:49:24 Gargoyle user.info sysinit: ping: bad address 'wp.pl'
Jun 8 13:49:24 Gargoyle daemon.notice netifd: wan (2925): Sending discover...
Jun 8 13:49:25 Gargoyle user.info sysinit: ping: bad address 'wp.pl'
Jun 8 13:49:26 Gargoyle user.info sysinit: ping: bad address 'wp.pl'
Jun 8 13:49:27 Gargoyle user.info sysinit: ping: bad address 'wp.pl'
Jun 8 13:49:27 Gargoyle daemon.notice netifd: wan (2925): Sending discover...
Jun 8 13:49:28 Gargoyle user.info sysinit: ping: bad address 'wp.pl'
Jun 8 13:49:28 Gargoyle user.notice usb-modeswitch: 1-1.1:1.0: Manufacturer=HUAWEI_Technology Product=HUAWEI_Mobile Serial=?
Jun 8 13:49:29 Gargoyle user.notice usb-modeswitch: 1-1.1:1.1: Manufacturer=HUAWEI_Technology Product=HUAWEI_Mobile Serial=?
Jun 8 13:49:29 Gargoyle user.info sysinit: ping: bad address 'wp.pl'
Jun 8 13:49:29 Gargoyle user.notice usb-modeswitch: 1-1.1:1.2: Manufacturer=HUAWEI_Technology Product=HUAWEI_Mobile Serial=?
Jun 8 13:49:29 Gargoyle user.notice usb-modeswitch: 1-1.1:1.3: Manufacturer=HUAWEI_Technology Product=HUAWEI_Mobile Serial=?
Jun 8 13:49:29 Gargoyle user.notice usb-modeswitch: 1-1.1:1.4: Manufacturer=HUAWEI_Technology Product=HUAWEI_Mobile Serial=?
Jun 8 13:49:30 Gargoyle user.info sysinit: ping: bad address 'wp.pl'
Jun 8 13:49:30 Gargoyle user.notice usb-modeswitch: 1-1.1:1.5: Manufacturer=HUAWEI_Technology Product=HUAWEI_Mobile Serial=?
Jun 8 13:49:30 Gargoyle user.notice usb-modeswitch: 1-1.1:1.6: Manufacturer=HUAWEI_Technology Product=HUAWEI_Mobile Serial=?
Jun 8 13:49:31 Gargoyle user.info sysinit: ping: bad address 'wp.pl'
Jun 8 13:49:32 Gargoyle user.info sysinit: ping: bad address 'wp.pl'
Jun 8 13:49:33 Gargoyle user.info sysinit: ping: bad
-------------------------------------------------------------------------------------------------------------------------------------------------------------------
# Put your custom commands here that should be executed once
# the system init finished. By default this file does nothing.
sleep 5
MODE="AT^NDISDUP=1,1,\"internet\"" gcom -d /dev/ttyUSB2 -s /etc/gcom/setmode.gco
ifup wan
(while true; do ping wp.pl > /dev/null; sleep 1; done) &
exit 0
~
~
~
~
~
~
~
~
~
~
~
~
~
~
~
~
- /etc/rc.local 1/7 14%uci show network pokaż.
uci show network pokaż.
Jakie wydać polecenie, lub gdzie to znajdę
faq się kłania: konsola po zalogowaniu przez ssh.
wiem ze po zalogowaniu przez ssh Nie wiedziałem tylko że chodzi o tą główną tabela zaraz po zalgowaniu bo pewnie o nią Teraz jestem na drugim mieszkaniu a na 3g i garygoyle mam przywrocone wczesniejsze ustawienia zrobie raz jeszcze konfiguracje wedlug poradnika i podam dane o ktore prosiles Pozdrawiam i dzięki wam za wsparcie
Cezary@
----------------------------------------------------------------
| |
| Gargoyle PL 1.5.10.0 (e9259ee) |
| OpenWrt Attitude Adjustment 12.09 (r36715) |
| Build time: 2013-05-25 08:33 CEST |
| |
| Cezary Jackiewicz (obsy), http://eko.one.pl |
| |
----------------------------------------------------------------
| Machine: TP-Link TL-WDR3600 v1 |
| Uptime: 0d, 00:01:28 |
| Load: 1.11 0.37 0.13 |
| Flash: free: 1.4M, total: 1.8M, used: 20% |
| Memory: free: 107356K, total: 126620K, used: 15% |
| WAN: |
| LAN: 192.168.1.1 |
| WLAN: mode: ap, ssid: Gargoyle, channel: 11, conn: 1 |
| WLAN: mode: ap, ssid: Gargoyle, channel: 36, conn: 0 |
----------------------------------------------------------------tutaj jest po przywróceniu konfiguracji:
----------------------------------------------------------------
| |
| Gargoyle PL 1.5.10.0 (e9259ee) |
| OpenWrt Attitude Adjustment 12.09 (r36715) |
| Build time: 2013-05-25 08:33 CEST |
| |
| Cezary Jackiewicz (obsy), http://eko.one.pl |
| |
----------------------------------------------------------------
| Machine: TP-Link TL-WDR3600 v1 |
| Uptime: 0d, 00:18:36 |
| Load: 0.18 0.16 0.14 |
| Flash: free: 1.4M, total: 1.8M, used: 20% |
| Memory: free: 106632K, total: 126620K, used: 15% |
| WAN: x.xxx.72.47, proto: 3g |
| LAN: 192.168.1.1 |
| WLAN: mode: ap, ssid: Gargoyle, channel: 11, conn: 1 |
| WLAN: mode: ap, ssid: Gargoyle, channel: 36, conn: 0 |
----------------------------------------------------------------To jest baner. uci show network miałes zrobić.
Po zmianie na NDIS według poradnika:
root@Gargoyle:~# uci show network
network.loopback=interface
network.loopback.ifname=lo
network.loopback.proto=static
network.loopback.ipaddr=127.0.0.1
network.loopback.netmask=255.0.0.0
network.lan=interface
network.lan.ifname=eth0.1
network.lan.type=bridge
network.lan.proto=static
network.lan.ipaddr=192.168.1.1
network.lan.netmask=255.255.255.0
network.lan.dns=192.168.1.1
network.wan=interface
network.wan.auto=0
network.wan.proto=dhcp
network.wan.ifname=usb
network.wan.macaddr=00:01:02:03:04:05
network.@switch[0]=switch
network.@switch[0].name=eth0
network.@switch[0].reset=1
network.@switch[0].enable_vlan=1
network.@switch_vlan[0]=switch_vlan
network.@switch_vlan[0].device=eth0
network.@switch_vlan[0].vlan=1
network.@switch_vlan[0].ports=0t 2 3 4 5
network.@switch_vlan[1]=switch_vlan
network.@switch_vlan[1].device=eth0
network.@switch_vlan[1].vlan=2
network.@switch_vlan[1].ports=0t 1poprzednia działająca konfiguracja, może ułatwi sprawę
root@Gargoyle:~# uci show network
network.loopback=interface
network.loopback.ifname=lo
network.loopback.proto=static
network.loopback.ipaddr=127.0.0.1
network.loopback.netmask=255.0.0.0
network.lan=interface
network.lan.ifname=eth0.1
network.lan.type=bridge
network.lan.proto=static
network.lan.ipaddr=192.168.1.1
network.lan.netmask=255.255.255.0
network.lan.dns=192.168.1.1
network.wan=interface
network.wan.auto=1
network.wan.proto=3g
network.wan.device=/dev/ttyUSB0
network.wan.apn=internet
network.wan.service=umts
network.wan.mobile_isp=custom
network.@switch[0]=switch
network.@switch[0].name=eth0
network.@switch[0].reset=1
network.@switch[0].enable_vlan=1
network.@switch_vlan[0]=switch_vlan
network.@switch_vlan[0].device=eth0
network.@switch_vlan[0].vlan=1
network.@switch_vlan[0].ports=0t 2 3 4 5
network.@switch_vlan[1]=switch_vlan
network.@switch_vlan[1].device=eth0
network.@switch_vlan[1].vlan=2
network.@switch_vlan[1].ports=0t 1ifconfig -a pokaż.
ifconfig -a pokaż.
Pierwszy działający, drugi po zmianie według poradnika.
root@Gargoyle:~# ifconfig
3g-wan Link encap:Point-to-Point Protocol
inet addr:31.174.244.47 P-t-P:10.64.64.64 Mask:255.255.255.255
UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1
RX packets:1485 errors:0 dropped:0 overruns:0 frame:0
TX packets:1060 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:3
RX bytes:1257159 (1.1 MiB) TX bytes:84279 (82.3 KiB)
br-lan Link encap:Ethernet HWaddr 64:70:02:D1:69:C2
inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:1031 errors:0 dropped:50 overruns:0 frame:0
TX packets:1240 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:78455 (76.6 KiB) TX bytes:1257273 (1.1 MiB)
eth0 Link encap:Ethernet HWaddr 64:70:02:D1:69:C2
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:228 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:19140 (18.6 KiB)
Interrupt:4
eth0.1 Link encap:Ethernet HWaddr 64:70:02:D1:69:C2
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:228 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:18228 (17.8 KiB)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:788 errors:0 dropped:0 overruns:0 frame:0
TX packets:788 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:47060 (45.9 KiB) TX bytes:47060 (45.9 KiB)
wlan0 Link encap:Ethernet HWaddr 64:70:02:D1:69:C3
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:1029 errors:0 dropped:0 overruns:0 frame:0
TX packets:1470 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:92849 (90.6 KiB) TX bytes:1304716 (1.2 MiB)
wlan1 Link encap:Ethernet HWaddr 64:70:02:D1:69:C4
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:228 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:22316 (21.7 KiB)
--------------------------------------------------------------------------------
root@Gargoyle:~# ifconfig
br-lan Link encap:Ethernet HWaddr 64:70:02:D1:69:C2
inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:707 errors:0 dropped:71 overruns:0 frame:0
TX packets:515 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:70844 (69.1 KiB) TX bytes:98213 (95.9 KiB)
eth0 Link encap:Ethernet HWaddr 64:70:02:D1:69:C2
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:755 errors:0 dropped:16 overruns:0 frame:0
TX packets:719 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:87871 (85.8 KiB) TX bytes:113935 (111.2 KiB)
Interrupt:4
eth0.1 Link encap:Ethernet HWaddr 64:70:02:D1:69:C2
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:600 errors:0 dropped:0 overruns:0 frame:0
TX packets:611 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:65331 (63.7 KiB) TX bytes:105203 (102.7 KiB)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:336 errors:0 dropped:0 overruns:0 frame:0
TX packets:336 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:21504 (21.0 KiB) TX bytes:21504 (21.0 KiB)
wlan0 Link encap:Ethernet HWaddr 64:70:02:D1:69:C3
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:106 errors:0 dropped:0 overruns:0 frame:0
TX packets:232 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:8293 (8.0 KiB) TX bytes:23419 (22.8 KiB)
wlan1 Link encap:Ethernet HWaddr 64:70:02:D1:69:C4
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:223 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:21998 (21.4 KiB)Raz że w konfigu masz usb co jest żle (usb0 jak już). Dwa - ty w ogóle takiego interfejsu nie masz. Pokaż wynik cat /proc/bus/usb/devices
Uff, pokazuję wyniki z obecnym ustawieniem wan z którym działa internet bo tak to za każdym razem przywracam tą konfigurację. Chodzi o usb0 w konfigu wan? Robiłem to kilka razy (bo gdy podaję jakieś info robię od początku według poradnika i z powrotem wracam do standardowych ustawień by mień int.) i z pośpiechu dodałem bez "0"
root@Gargoyle:~# cat /proc/bus/usb/devices
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 1
B: Alloc= 1/800 us ( 0%), #Int= 2, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0002 Rev= 3.03
S: Manufacturer=Linux 3.3.8 ehci_hcd
S: Product=Generic Platform EHCI Controller
S: SerialNumber=ehci-platform
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 4
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=05e3 ProdID=0608 Rev=77.64
S: Product=USB2.0 Hub
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 1 Ivl=256ms
T: Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#= 4 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=12d1 ProdID=1436 Rev= 0.00
S: Manufacturer=HUAWEI Technology
S: Product=HUAWEI Mobile
C:* #Ifs= 7 Cfg#= 1 Atr=e0 MxPwr=500mA
A: FirstIf#= 1 IfCount= 2 Cls=02(comm.) Sub=00 Prot=00
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 1 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=ff Driver=cdc_ether
E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 5 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 6 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
root@Gargoyle:~#ifconfig -a ma te usb0 (lub wwan0) pokazać. Jak nie ma to nic nie zrobisz.
tzn. że co? modem który u innych działa tutaj nie będzie działał w NDIS? To też nic nie pomoże według tego poradnika:
Dopóki nie będziesz miał interfejsu to nic nie da się zrobić dalej.
Dopóki nie będziesz miał interfejsu to nic nie da się zrobić dalej.
Rozumiem, wiesz gdzie może leżeć błąd?
Zmień sterownik z ether na huawei (w pakietach jest).
Jeszcze odnosnie zakupu WNDR3800 prosze Was o potwierdzenie, czy ten router jest zwyczajnym routerem do sieci osiedlowych bez xDSL.
http://www.alternate.pl/Netgear/Netgear … ct/862916/?
http://www.thomas-it.pl/n600-wifi-db-ro … 800-100pes
Rozumiem ze DGND3800 nie jest tym co trzeba? Tak wyglada jakby to byl DSL.
Strony Poprzednia 1 … 9 10 11 12 13 … 16 Następna
Zaloguj się lub zarejestruj by napisać odpowiedź
eko.one.pl → Oprogramowanie / Software → Witam, najlepszych :) Dobór Ruterka..
Forum oparte o PunBB, wspierane przez Informer Technologies, Inc