1 Temat przez tobbit

  • tobbit
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2013-01-22
  • Posty: 29

Temat: Problem z HDD

Witam!
podpiąłem HDD 2,5" w kieszeni do 1043nd i mam taki dmesg:

[  213.040000] sd 0:0:0:0: [sda] Test WP failed, assume Write Enabled
[  213.050000] sd 0:0:0:0: [sda] Asking for cache data failed
[  213.060000] sd 0:0:0:0: [sda] Assuming drive cache: write through
[  213.060000] sd 0:0:0:0: [sda] Attached SCSI disk
[  213.210000] Compat-drivers backport release: compat-drivers-2012-09-04-2-gddac993
[  213.220000] Backport based on wireless-testing.git master-2012-09-07
[  213.220000] compat.git: wireless-testing.git
[  213.390000] cfg80211: Calling CRDA to update world regulatory domain
[  213.400000] cfg80211: World regulatory domain updated:
[  213.400000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[  213.410000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[  213.420000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[  213.420000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[  213.430000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[  213.440000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[  214.790000] ath: EEPROM regdomain: 0x0
[  214.790000] ath: EEPROM indicates default country code should be used
[  214.790000] ath: doing EEPROM country->regdmn map search
[  214.790000] ath: country maps to regdmn code: 0x3a
[  214.790000] ath: Country alpha2 being used: US
[  214.790000] ath: Regpair used: 0x3a
[  214.790000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[  214.790000] ieee80211 phy0: Atheros AR9100 MAC/BB Rev:7 AR2133 RF Rev:a2 mem=0xb80c0000, irq=2
[  214.800000] cfg80211: Calling CRDA for country: US
[  214.810000] cfg80211: Regulatory domain changed to country: US
[  214.820000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[  214.820000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[  214.830000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
[  214.840000] cfg80211:   (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[  214.850000] cfg80211:   (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[  214.860000] cfg80211:   (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[  214.860000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
[  215.110000] RPC: Registered named UNIX socket transport module.
[  215.120000] RPC: Registered udp transport module.
[  215.120000] RPC: Registered tcp transport module.
[  215.120000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[  215.700000] PPP generic driver version 2.4.2
[  215.860000] tun: Universal TUN/TAP device driver, 1.6
[  215.860000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[  215.990000] GRE over IPv4 demultiplexor driver
[  216.110000] ip_gre: Unknown symbol icmpv6_send (err 0)
[  216.460000] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[  216.570000] ip_tables: (C) 2000-2006 Netfilter Core Team
[  217.000000] NET: Registered protocol family 24
[  217.160000] nf_conntrack version 0.5.0 (456 buckets, 1824 max)
[  217.690000] PPTP driver version 0.8.5
[  218.490000] xt_time: kernel timezone is -0000
[  219.340000]  Hooked IMQ after mangle on PREROUTING
[  219.340000]  Hooked IMQ after nat on POSTROUTING
[  219.350000] IMQ driver loaded successfully. (numdevs = 2, numqueues = 1)
[  219.540000] Netfilter messages via NETLINK v0.30.
[  219.770000] ip_set: protocol 6
[  220.420000] usbcore: registered new interface driver cdc_acm
[  220.420000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[  220.590000] usbcore: registered new interface driver usblp
[  220.620000] usbcore: registered new interface driver usbserial
[  220.620000] USB Serial support registered for generic
[  220.630000] usbcore: registered new interface driver usbserial_generic
[  220.640000] usbserial: USB Serial Driver core
[  220.800000] usbcore: registered new interface driver ums-alauda
[  220.820000] usbcore: registered new interface driver ums-cypress
[  220.850000] usbcore: registered new interface driver ums-datafab
[  220.930000] usbcore: registered new interface driver ums-freecom
[  220.950000] usbcore: registered new interface driver ums-isd200
[  220.980000] usbcore: registered new interface driver ums-jumpshot
[  221.010000] usbcore: registered new interface driver ums-karma
[  221.040000] usbcore: registered new interface driver ums-sddr09
[  221.060000] usbcore: registered new interface driver ums-sddr55
[  221.090000] usbcore: registered new interface driver ums-usbat
[  221.210000] usbcore: registered new interface driver cdc_ncm
[  221.320000] USB Serial support registered for GSM modem (1-port)
[  221.320000] usbcore: registered new interface driver option
[  221.330000] option: v0.7.2:USB Driver for GSM modems
[  221.430000] USB Serial support registered for Sierra USB modem
[  221.430000] usbcore: registered new interface driver sierra
[  221.440000] sierra: v.1.7.16:USB Driver for Sierra Wireless USB modems
[  221.580000] fuse init (API version 7.18)
[  227.700000] ar71xx: pll_reg 0xb8050014: 0x1a000000
[  228.000000] eth0: link up (1000Mbps/Full duplex)
[  228.010000] device eth0.1 entered promiscuous mode
[  228.010000] device eth0 entered promiscuous mode
[  228.030000] br-lan: port 1(eth0.1) entered forwarding state
[  228.030000] br-lan: port 1(eth0.1) entered forwarding state
[  230.030000] br-lan: port 1(eth0.1) entered forwarding state
[  241.140000] disktype: sending ioctl 5305 to a partition!
[  241.140000] disktype: sending ioctl 5305 to a partition!
[  241.200000] disktype: sending ioctl 5305 to a partition!
[  241.200000] disktype: sending ioctl 5305 to a partition!
[  241.540000] Adding 162300k swap on /dev/sdb2.  Priority:-1 extents:1 across:162300k
[  242.390000] disktype: sending ioctl 5305 to a partition!
[  242.390000] disktype: sending ioctl 5305 to a partition!
[  242.450000] disktype: sending ioctl 5305 to a partition!
[  242.450000] disktype: sending ioctl 5305 to a partition!
[  242.520000] Adding 162300k swap on /dev/sdb2.  Priority:-1 extents:1 across:162300k
[  243.590000] disktype: sending ioctl 5305 to a partition!
[  243.600000] disktype: sending ioctl 5305 to a partition!
[  243.690000] Adding 162300k swap on /dev/sdb2.  Priority:-1 extents:1 across:162300k
[  244.970000] Adding 162300k swap on /dev/sdb2.  Priority:-1 extents:1 across:162300k
[  245.850000] Adding 162300k swap on /dev/sdb2.  Priority:-1 extents:1 across:162300k
[  246.690000] scsi_verify_blk_ioctl: 10 callbacks suppressed
[  246.700000] disktype: sending ioctl 5305 to a partition!
[  246.700000] disktype: sending ioctl 5305 to a partition!
[  246.740000] disktype: sending ioctl 5305 to a partition!
[  246.750000] disktype: sending ioctl 5305 to a partition!
[  246.790000] Adding 162300k swap on /dev/sdb2.  Priority:-1 extents:1 across:162300k
[  247.260000] disktype: sending ioctl 5305 to a partition!
[  247.260000] disktype: sending ioctl 5305 to a partition!
[  247.300000] disktype: sending ioctl 5305 to a partition!
[  247.310000] disktype: sending ioctl 5305 to a partition!
[  247.350000] Adding 162300k swap on /dev/sdb2.  Priority:-1 extents:1 across:162300k
[  247.400000] head: sending ioctl 540d to a partition!
[  247.410000] head: sending ioctl 540d to a partition!
[  247.840000] Adding 162300k swap on /dev/sdb2.  Priority:-1 extents:1 across:162300k
[  248.330000] Adding 162300k swap on /dev/sdb2.  Priority:-1 extents:1 across:162300k
[  248.840000] Adding 162300k swap on /dev/sdb2.  Priority:-1 extents:1 across:162300k
[  264.340000] cfg80211: Calling CRDA for country: PL
[  264.340000] cfg80211: Regulatory domain changed to country: PL
[  264.350000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[  264.360000] cfg80211:   (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[  264.360000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[  264.370000] cfg80211:   (5250000 KHz - 5330000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[  264.380000] cfg80211:   (5490000 KHz - 5710000 KHz @ 40000 KHz), (N/A, 2700 mBm)
[  271.930000] ipt_bandwidth: timezone shift of 60 minutes detected, adjusting
[  271.940000]                old minutes west=0, new minutes west=-60
[  803.430000] usb 1-1.2: USB disconnect, device number 3
[  804.140000] scsi_verify_blk_ioctl: 14 callbacks suppressed
[  804.140000] disktype: sending ioctl 5305 to a partition!
[  804.150000] disktype: sending ioctl 5305 to a partition!
[  804.180000] disktype: sending ioctl 5305 to a partition!
[  804.190000] disktype: sending ioctl 5305 to a partition!
[  804.230000] Adding 162300k swap on /dev/sdb2.  Priority:-1 extents:1 across:162300k
[  806.490000] usb 1-1.2: new high-speed USB device number 5 using ehci-platform
[  806.610000] scsi2 : usb-storage 1-1.2:1.0
[  807.610000] scsi 2:0:0:0: Direct-Access     Ext Hard  Disk                 PQ: 0 ANSI: 4
[  807.620000] sd 2:0:0:0: [sda] Spinning up disk.......................................................................................................not responding...
[  908.630000] sd 2:0:0:0: [sda] READ CAPACITY failed
[  908.640000] sd 2:0:0:0: [sda]  Result: hostbyte=0x00 driverbyte=0x08
[  908.640000] sd 2:0:0:0: [sda]  Sense Key : 0x2 [current]
[  908.650000] sd 2:0:0:0: [sda]  ASC=0x4 ASCQ=0x0
[  908.650000] sd 2:0:0:0: [sda] Test WP failed, assume Write Enabled
[  908.660000] sd 2:0:0:0: [sda] Asking for cache data failed
[  908.670000] sd 2:0:0:0: [sda] Assuming drive cache: write through
[  908.680000] sd 2:0:0:0: [sda] Spinning up disk...
[  909.190000] disktype: sending ioctl 5305 to a partition!
[  909.190000] disktype: sending ioctl 5305 to a partition!
[  909.230000] disktype: sending ioctl 5305 to a partition!
[  909.230000] disktype: sending ioctl 5305 to a partition!
[  909.280000] Adding 162300k swap on /dev/sdb2.  Priority:-1 extents:1 across:162300k
[  909.690000] ....................................................................................................not responding...
[ 1009.680000] sd 2:0:0:0: [sda] READ CAPACITY failed
[ 1009.690000] sd 2:0:0:0: [sda]  Result: hostbyte=0x00 driverbyte=0x08
[ 1009.690000] sd 2:0:0:0: [sda]  Sense Key : 0x2 [current]
[ 1009.700000] sd 2:0:0:0: [sda]  ASC=0x4 ASCQ=0x0
[ 1009.700000] sd 2:0:0:0: [sda] Test WP failed, assume Write Enabled
[ 1009.710000] sd 2:0:0:0: [sda] Asking for cache data failed
[ 1009.720000] sd 2:0:0:0: [sda] Assuming drive cache: write through
[ 1009.720000] sd 2:0:0:0: [sda] Attached SCSI disk
[ 3478.870000] usb 1-1.2: USB disconnect, device number 5
[ 3479.380000] disktype: sending ioctl 5305 to a partition!
[ 3479.380000] disktype: sending ioctl 5305 to a partition!
[ 3479.420000] disktype: sending ioctl 5305 to a partition!
[ 3479.430000] disktype: sending ioctl 5305 to a partition!
[ 3479.470000] Adding 162300k swap on /dev/sdb2.  Priority:-1 extents:1 across:162300k
[ 3889.470000] usb 1-1.3: new high-speed USB device number 6 using ehci-platform
[ 3889.580000] scsi3 : usb-storage 1-1.3:1.0
[ 3890.590000] scsi 3:0:0:0: Direct-Access     Ext Hard  Disk                 PQ: 0 ANSI: 4
[ 3890.600000] sd 3:0:0:0: [sda] Spinning up disk.......................................................................................................not responding...
[ 3991.610000] sd 3:0:0:0: [sda] READ CAPACITY failed
[ 3991.610000] sd 3:0:0:0: [sda]  Result: hostbyte=0x00 driverbyte=0x08
[ 3991.620000] sd 3:0:0:0: [sda]  Sense Key : 0x2 [current]
[ 3991.630000] sd 3:0:0:0: [sda]  ASC=0x4 ASCQ=0x0
[ 3991.630000] sd 3:0:0:0: [sda] Test WP failed, assume Write Enabled
[ 3991.640000] sd 3:0:0:0: [sda] Asking for cache data failed
[ 3991.650000] sd 3:0:0:0: [sda] Assuming drive cache: write through
[ 3991.660000] sd 3:0:0:0: [sda] Spinning up disk...
[ 3992.170000] disktype: sending ioctl 5305 to a partition!
[ 3992.170000] disktype: sending ioctl 5305 to a partition!
[ 3992.210000] disktype: sending ioctl 5305 to a partition!
[ 3992.210000] disktype: sending ioctl 5305 to a partition!
[ 3992.250000] Adding 162300k swap on /dev/sdb2.  Priority:-1 extents:1 across:162300k
[ 3992.670000] .......................................

Hdd jest wpiety do huba wraz z pendrivem, na nim jest extroot. Kabel do dysku ma dwie wtyczki usb A: jedna DATA jest wpięta do huba, druga POWER jest wpięta do zasilacza 5V

fdisk daje coś takiego jak próbuje wejść na /dev/sda

root@Gargoyle:~# fdisk /dev/sda
Welcome to fdisk (util-linux 2.21.2).

Changes will remain in memory only, until you decide to write them.
Be careful before using the write command.

fdisk: unable to read /dev/sda: Invalid argument

2 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,590

Odp: Problem z HDD

disk.......................................................................................................not responding...

Nie czyta go w ogóle.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

3 Odpowiedź przez tobbit

  • tobbit
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2013-01-22
  • Posty: 29

Odp: Problem z HDD

Mam problem z hubem bo wpiąłem go bezpośrednio do usb i czyta go:

fstype=squashfs,jffs2 noinitrd
[    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 28976k/32768k available (2227k kernel code, 3792k reserved, 421k data, 216k init, 0k highmem)
[    0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:51
[    0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[    0.080000] pid_max: default: 32768 minimum: 301
[    0.080000] Mount-cache hash table entries: 512
[    0.090000] NET: Registered protocol family 16
[    0.090000] gpiochip_add: registered GPIOs 0 to 21 on device: ath79
[    0.100000] MIPS: machine is TP-LINK TL-WR1043ND
[    0.360000] bio: create slab <bio-0> at 0
[    0.370000] Switching to clocksource MIPS
[    0.380000] NET: Registered protocol family 2
[    0.380000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.380000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[    0.390000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.390000] TCP: Hash tables configured (established 1024 bind 1024)
[    0.400000] TCP reno registered
[    0.400000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.410000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.420000] NET: Registered protocol family 1
[    0.420000] PCI: CLS 0 bytes, default 32
[    0.440000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.440000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.450000] msgmni has been set to 56
[    0.460000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
[    0.470000] io scheduler noop registered
[    0.470000] io scheduler deadline registered (default)
[    0.470000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.510000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[    0.510000] console [ttyS0] enabled, bootconsole disabled
[    0.530000] m25p80 spi0.0: found s25sl064a, expected m25p80
[    0.530000] m25p80 spi0.0: s25sl064a (8192 Kbytes)
[    0.540000] 5 tp-link partitions found on MTD device spi0.0
[    0.540000] Creating 5 MTD partitions on "spi0.0":
[    0.550000] 0x000000000000-0x000000020000 : "u-boot"
[    0.560000] 0x000000020000-0x00000010da00 : "kernel"
[    0.560000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.580000] 0x00000010da00-0x0000007f0000 : "rootfs"
[    0.580000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.590000] mtd: partition "rootfs" set to be root filesystem
[    0.600000] mtd: partition "rootfs_data" created automatically, ofs=630000, len=1C0000
[    0.610000] 0x000000630000-0x0000007f0000 : "rootfs_data"
[    0.620000] 0x0000007f0000-0x000000800000 : "art"
[    0.620000] 0x000000020000-0x0000007f0000 : "firmware"
[    0.630000] Realtek RTL8366RB ethernet switch driver version 0.2.3
[    0.750000] rtl8366rb rtl8366rb: using GPIO pins 18 (SDA) and 19 (SCK)
[    0.750000] rtl8366rb rtl8366rb: RTL5937 ver. 3 chip found
[    0.930000] rtl8366rb: probed
[    0.940000] eth0: Atheros AG71xx at 0xb9000000, irq 4
[    1.240000] TCP cubic registered
[    1.250000] NET: Registered protocol family 17
[    1.250000] Bridge firewalling registered
[    1.260000] Ebtables v2.0 registered
[    1.260000] 8021q: 802.1Q VLAN Support v1.8
[    1.270000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    1.280000] Freeing unused kernel memory: 216k freed
[    3.700000] ar71xx: pll_reg 0xb8050014: 0x1a000000
[    3.700000] eth0: link up (1000Mbps/Full duplex)
[    3.860000] Registered led device: tp-link:green:usb
[    3.860000] Registered led device: tp-link:green:system
[    3.860000] Registered led device: tp-link:green:qss
[    3.860000] Registered led device: tp-link:green:wlan
[    7.190000] JFFS2 notice: (440) jffs2_build_xattr_subsystem: complete building xattr subsystem, 2 of xdatum (1 unchecked, 1 orphan) and 75 of xref (0 dead, 56 orphan) found.
[    8.090000] SCSI subsystem initialized
[    8.330000] usbcore: registered new interface driver usbfs
[    8.330000] usbcore: registered new interface driver hub
[    8.340000] usbcore: registered new device driver usb
[    9.000000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    9.000000] ehci-platform ehci-platform: Generic Platform EHCI Controller
[    9.010000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[    9.050000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[    9.070000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[    9.070000] hub 1-0:1.0: USB hub found
[    9.080000] hub 1-0:1.0: 1 port detected
[    9.140000] Initializing USB Mass Storage driver...
[    9.150000] usbcore: registered new interface driver usb-storage
[    9.150000] USB Mass Storage support registered.
[   30.110000] eth0: link down
[   30.990000] Compat-drivers backport release: compat-drivers-2012-09-04-2-gddac993
[   31.000000] Backport based on wireless-testing.git master-2012-09-07
[   31.010000] compat.git: wireless-testing.git
[   31.170000] cfg80211: Calling CRDA to update world regulatory domain
[   31.180000] cfg80211: World regulatory domain updated:
[   31.180000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   31.190000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   31.200000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   31.210000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   31.210000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   31.220000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   32.580000] ath: EEPROM regdomain: 0x0
[   32.580000] ath: EEPROM indicates default country code should be used
[   32.580000] ath: doing EEPROM country->regdmn map search
[   32.580000] ath: country maps to regdmn code: 0x3a
[   32.580000] ath: Country alpha2 being used: US
[   32.580000] ath: Regpair used: 0x3a
[   32.580000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   32.580000] ieee80211 phy0: Atheros AR9100 MAC/BB Rev:7 AR2133 RF Rev:a2 mem=0xb80c0000, irq=2
[   32.590000] cfg80211: Calling CRDA for country: US
[   32.600000] cfg80211: Regulatory domain changed to country: US
[   32.610000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   32.610000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[   32.620000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
[   32.630000] cfg80211:   (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   32.640000] cfg80211:   (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   32.650000] cfg80211:   (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   32.650000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
[   32.900000] RPC: Registered named UNIX socket transport module.
[   32.900000] RPC: Registered udp transport module.
[   32.910000] RPC: Registered tcp transport module.
[   32.910000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[   33.490000] PPP generic driver version 2.4.2
[   33.650000] tun: Universal TUN/TAP device driver, 1.6
[   33.650000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[   33.780000] GRE over IPv4 demultiplexor driver
[   33.900000] ip_gre: Unknown symbol icmpv6_send (err 0)
[   34.250000] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[   34.360000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   34.790000] NET: Registered protocol family 24
[   34.950000] nf_conntrack version 0.5.0 (456 buckets, 1824 max)
[   35.480000] PPTP driver version 0.8.5
[   36.290000] xt_time: kernel timezone is -0000
[   37.140000]  Hooked IMQ after mangle on PREROUTING
[   37.150000]  Hooked IMQ after nat on POSTROUTING
[   37.150000] IMQ driver loaded successfully. (numdevs = 2, numqueues = 1)
[   37.340000] Netfilter messages via NETLINK v0.30.
[   37.580000] ip_set: protocol 6
[   38.220000] usbcore: registered new interface driver cdc_acm
[   38.230000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[   38.390000] usbcore: registered new interface driver usblp
[   38.420000] usbcore: registered new interface driver usbserial
[   38.420000] USB Serial support registered for generic
[   38.430000] usbcore: registered new interface driver usbserial_generic
[   38.440000] usbserial: USB Serial Driver core
[   38.600000] usbcore: registered new interface driver ums-alauda
[   38.630000] usbcore: registered new interface driver ums-cypress
[   38.650000] usbcore: registered new interface driver ums-datafab
[   38.730000] usbcore: registered new interface driver ums-freecom
[   38.750000] usbcore: registered new interface driver ums-isd200
[   38.780000] usbcore: registered new interface driver ums-jumpshot
[   38.810000] usbcore: registered new interface driver ums-karma
[   38.840000] usbcore: registered new interface driver ums-sddr09
[   38.860000] usbcore: registered new interface driver ums-sddr55
[   38.890000] usbcore: registered new interface driver ums-usbat
[   39.010000] usbcore: registered new interface driver cdc_ncm
[   39.120000] USB Serial support registered for GSM modem (1-port)
[   39.120000] usbcore: registered new interface driver option
[   39.130000] option: v0.7.2:USB Driver for GSM modems
[   39.230000] USB Serial support registered for Sierra USB modem
[   39.230000] usbcore: registered new interface driver sierra
[   39.240000] sierra: v.1.7.16:USB Driver for Sierra Wireless USB modems
[   39.380000] fuse init (API version 7.18)
[   44.810000] usb 1-1: new high-speed USB device number 2 using ehci-platform
[   44.970000] scsi0 : usb-storage 1-1:1.0
[   45.520000] ar71xx: pll_reg 0xb8050014: 0x1a000000
[   45.820000] eth0: link up (1000Mbps/Full duplex)
[   45.830000] device eth0.1 entered promiscuous mode
[   45.830000] device eth0 entered promiscuous mode
[   45.850000] br-lan: port 1(eth0.1) entered forwarding state
[   45.850000] br-lan: port 1(eth0.1) entered forwarding state
[   46.210000] scsi 0:0:0:0: Direct-Access     Ext Hard  Disk                 PQ: 0 ANSI: 4
[   46.220000] sd 0:0:0:0: [sda] 390721968 512-byte logical blocks: (200 GB/186 GiB)
[   46.240000] sd 0:0:0:0: [sda] Write Protect is off
[   46.240000] sd 0:0:0:0: [sda] Mode Sense: 10 00 00 00
[   46.240000] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   46.670000]  sda: sda4
[   46.710000] sd 0:0:0:0: [sda] Attached SCSI disk
[   47.850000] br-lan: port 1(eth0.1) entered forwarding state
[   75.190000] head: sending ioctl 540d to a partition!
[   75.190000] head: sending ioctl 540d to a partition!
[   77.770000] disktype: sending ioctl 5305 to a partition!
[   77.780000] disktype: sending ioctl 5305 to a partition!
[   82.260000] cfg80211: Calling CRDA for country: PL
[   82.260000] cfg80211: Regulatory domain changed to country: PL
[   82.270000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   82.270000] cfg80211:   (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[   82.280000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[   82.290000] cfg80211:   (5250000 KHz - 5330000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[   82.300000] cfg80211:   (5490000 KHz - 5710000 KHz @ 40000 KHz), (N/A, 2700 mBm)
[   93.730000] ipt_bandwidth: timezone shift of 60 minutes detected, adjusting
[   93.740000]                old minutes west=0, new minutes west=-60
root@Gargoyle:~#

4 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,590

Odp: Problem z HDD

Masz problem z hubem więc smile

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

5 Odpowiedź przez tobbit

  • tobbit
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2013-01-22
  • Posty: 29

Odp: Problem z HDD

muszę kupić coś aktywnego, 7 portów. Będę szukał tych co piszą że działają na openwrt

6 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,590

Odp: Problem z HDD

Pewnie kupisz taki sam i okaże się że w środku jest znów coś innego.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona