• Zarejestrowany: 2011-03-23
  • Posty: 328

Temat: Kamera Trust WB-1100G

Kamera Trust WB-1100G

Debian wykrywa ją jako: Microdia TwinkleCam USB Camera ID: 0c45:600d

Szukałem na internecie jaki sterownik ją obsługuje i waham się pomiędzy:
sn9c102, a kmod-video-gspca-spca5xx (tylko, który jak już).

Postępując wg. instrukcji:

Cezary napisał/a:

Jeżeli nie wiemy przez co kamera USB jest obsługiwana - należy zainstalować wszystkie dostępne pakiety zawierające kmod-video- w nazwie.

wykonałem:

# opkg update
# opkg install kmod-usb-core kmod-usb2 kmod-video-core
# opkg install kmod-video-gspca-core kmod-video-gspca-(od 500 do 561)
# opkg install kmod-video-sn9c102

następnie podpiąłem kamerkę. Sprawdzam jej dostępność:

# ls -al /dev/video*

i polecenie nic nie zwraca.

Przy podłączonej kamerce wykonuje restart routera i ...... router uruchamia się i po ok 30sek następuje jego restart i tak w nieskończoność (nie ma możliwości zalogować się na router po SSH czy web gui). Obecnie odpiąłem pendrive z extrootem i przy podłączonej kamerce otrzymuję następujący wynik polecenia dmesg:

root@Gargoyle:~# dmesg
[    0.000000] Linux version 3.3.8 (cezary@eko.one.pl) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #29 Fri Dec 7 18:00:25 CET 2012
[    0.000000] MyLoader: sysp=aaaa5554, boardp=aaaa5554, parts=aaaa5554
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[    0.000000] SoC: Atheros AR9130 rev 2
[    0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:5.000MHz
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 02000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone PFN ranges:
[    0.000000]   Normal   0x00000000 -> 0x00002000
[    0.000000] Movable zone start PFN for each node
[    0.000000] Early memory PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00002000
[    0.000000] On node 0 totalpages: 8192
[    0.000000] free_area_init_node: node 0, pgdat 802f5cb0, node_mem_map 81000000
[    0.000000]   Normal zone: 64 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 8128 pages, LIFO batch:0
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
[    0.000000] Kernel command line:  board=WRT160NL console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
[    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 28976k/32768k available (2227k kernel code, 3792k reserved, 421k data, 216k init, 0k highmem)
[    0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:51
[    0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[    0.080000] pid_max: default: 32768 minimum: 301
[    0.080000] Mount-cache hash table entries: 512
[    0.090000] NET: Registered protocol family 16
[    0.090000] gpiochip_add: registered GPIOs 0 to 21 on device: ath79
[    0.100000] MIPS: machine is Linksys WRT160NL
[    0.610000] bio: create slab <bio-0> at 0
[    0.620000] Switching to clocksource MIPS
[    0.630000] NET: Registered protocol family 2
[    0.630000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.630000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[    0.640000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.640000] TCP: Hash tables configured (established 1024 bind 1024)
[    0.650000] TCP reno registered
[    0.650000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.660000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.670000] NET: Registered protocol family 1
[    0.670000] PCI: CLS 0 bytes, default 32
[    0.690000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.690000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.700000] msgmni has been set to 56
[    0.710000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
[    0.710000] io scheduler noop registered
[    0.720000] io scheduler deadline registered (default)
[    0.720000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.760000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[    0.760000] console [ttyS0] enabled, bootconsole disabled
[    0.780000] m25p80 spi0.0: found mx25l6405d, expected m25p80
[    0.780000] m25p80 spi0.0: mx25l6405d (8192 Kbytes)
[    0.790000] 6 wrt160nl partitions found on MTD device spi0.0
[    0.790000] Creating 6 MTD partitions on "spi0.0":
[    0.800000] 0x000000000000-0x000000040000 : "u-boot"
[    0.810000] 0x000000040000-0x000000190000 : "kernel"
[    0.810000] 0x000000190000-0x0000007e0000 : "rootfs"
[    0.820000] mtd: partition "rootfs" set to be root filesystem
[    0.820000] mtd: partition "rootfs_data" created automatically, ofs=6A0000, len=140000
[    0.830000] 0x0000006a0000-0x0000007e0000 : "rootfs_data"
[    0.840000] 0x0000007e0000-0x0000007f0000 : "nvram"
[    0.850000] 0x0000007f0000-0x000000800000 : "art"
[    0.850000] 0x000000040000-0x0000007e0000 : "firmware"
[    0.870000] ag71xx_mdio: probed
[    0.870000] eth0: Atheros AG71xx at 0xb9000000, irq 4
[    1.190000] Registering RTL8306SD switch with Chip ID: 0x5988, version: 0x0000
[    1.200000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.0:00 [uid=00008306, driver=Realtek RTL8306S]
[    1.210000] eth1: Atheros AG71xx at 0xba000000, irq 5
[    1.510000] ag71xx ag71xx.1: eth1: connected to PHY at ag71xx-mdio.0:04 [uid=00008306, driver=Realtek RTL8306S]
[    1.520000] TCP cubic registered
[    1.530000] NET: Registered protocol family 17
[    1.530000] Bridge firewalling registered
[    1.540000] Ebtables v2.0 registered
[    1.540000] 8021q: 802.1Q VLAN Support v1.8
[    1.550000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    1.560000] Freeing unused kernel memory: 216k freed
[    4.210000] Registered led device: wrt160nl:blue:power
[    4.210000] Registered led device: wrt160nl:amber:wps
[    4.210000] Registered led device: wrt160nl:blue:wps
[    4.210000] Registered led device: wrt160nl:blue:wlan
[    5.210000] ar71xx: pll_reg 0xb8050014: 0x13000a44
[    5.210000] eth0: link up (100Mbps/Full duplex)
[    7.540000] JFFS2 notice: (467) jffs2_build_xattr_subsystem: complete building xattr subsystem, 2 of xdatum (1 unchecked, 1 orphan) and 53 of xref (0 dead, 24 orphan) found.
[    8.450000] SCSI subsystem initialized
[    8.690000] usbcore: registered new interface driver usbfs
[    8.690000] usbcore: registered new interface driver hub
[    8.700000] usbcore: registered new device driver usb
[    9.290000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    9.300000] ehci-platform ehci-platform: Generic Platform EHCI Controller
[    9.310000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[    9.340000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[    9.360000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[    9.360000] hub 1-0:1.0: USB hub found
[    9.370000] hub 1-0:1.0: 1 port detected
[    9.430000] Initializing USB Mass Storage driver...
[    9.440000] usbcore: registered new interface driver usb-storage
[    9.450000] USB Mass Storage support registered.
[    9.700000] usb 1-1: new high-speed USB device number 2 using ehci-platform
[    9.850000] hub 1-1:1.0: USB hub found
[    9.850000] hub 1-1:1.0: 4 ports detected
[   30.400000] eth0: link down
[   31.280000] Compat-drivers backport release: compat-drivers-2012-09-04-2-gddac993
[   31.290000] Backport based on wireless-testing.git master-2012-09-07
[   31.300000] compat.git: wireless-testing.git
[   31.460000] cfg80211: Calling CRDA to update world regulatory domain
[   31.470000] cfg80211: World regulatory domain updated:
[   31.480000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   31.480000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   31.490000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   31.500000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   31.510000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   31.520000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   32.830000] ath: EEPROM regdomain: 0x0
[   32.830000] ath: EEPROM indicates default country code should be used
[   32.830000] ath: doing EEPROM country->regdmn map search
[   32.830000] ath: country maps to regdmn code: 0x3a
[   32.830000] ath: Country alpha2 being used: US
[   32.830000] ath: Regpair used: 0x3a
[   32.830000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   32.830000] ieee80211 phy0: Atheros AR9100 MAC/BB Rev:7 AR2122 RF Rev:a2 mem=0xb80c0000, irq=2
[   32.850000] cfg80211: Calling CRDA for country: US
[   32.850000] cfg80211: Regulatory domain changed to country: US
[   32.860000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   32.860000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[   32.870000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
[   32.880000] cfg80211:   (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   32.890000] cfg80211:   (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   32.900000] cfg80211:   (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   32.900000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
[   33.150000] RPC: Registered named UNIX socket transport module.
[   33.150000] RPC: Registered udp transport module.
[   33.160000] RPC: Registered tcp transport module.
[   33.160000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[   33.680000] PPP generic driver version 2.4.2
[   33.830000] tun: Universal TUN/TAP device driver, 1.6
[   33.840000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[   34.180000] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[   34.300000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   34.810000] NET: Registered protocol family 24
[   34.960000] nf_conntrack version 0.5.0 (456 buckets, 1824 max)
[   36.210000] xt_time: kernel timezone is -0000
[   36.740000]  Hooked IMQ after mangle on PREROUTING
[   36.750000]  Hooked IMQ after nat on POSTROUTING
[   36.750000] IMQ driver loaded successfully. (numdevs = 2, numqueues = 1)
[   36.980000] Netfilter messages via NETLINK v0.30.
[   37.110000] ip_set: protocol 6
[   37.710000] usbcore: registered new interface driver cdc_acm
[   37.710000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[   37.840000] usbcore: registered new interface driver usblp
[   37.870000] usbcore: registered new interface driver usbserial
[   37.880000] USB Serial support registered for generic
[   37.890000] usbcore: registered new interface driver usbserial_generic
[   37.890000] usbserial: USB Serial Driver core
[   38.050000] usbcore: registered new interface driver ums-alauda
[   38.080000] usbcore: registered new interface driver ums-cypress
[   38.100000] usbcore: registered new interface driver ums-datafab
[   38.180000] usbcore: registered new interface driver ums-freecom
[   38.200000] usbcore: registered new interface driver ums-isd200
[   38.230000] usbcore: registered new interface driver ums-jumpshot
[   38.250000] usbcore: registered new interface driver ums-karma
[   38.280000] usbcore: registered new interface driver ums-sddr09
[   38.310000] usbcore: registered new interface driver ums-sddr55
[   38.330000] usbcore: registered new interface driver ums-usbat
[   38.460000] USB Serial support registered for GSM modem (1-port)
[   38.470000] usbcore: registered new interface driver option
[   38.470000] option: v0.7.2:USB Driver for GSM modems
[   38.520000] USB Serial support registered for Sierra USB modem
[   38.530000] usbcore: registered new interface driver sierra
[   38.540000] sierra: v.1.7.16:USB Driver for Sierra Wireless USB modems
[   38.680000] fuse init (API version 7.18)
[   42.960000] device eth0 entered promiscuous mode
[   44.530000] cfg80211: Calling CRDA for country: PL
[   44.540000] cfg80211: Regulatory domain changed to country: PL
[   44.540000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   44.550000] cfg80211:   (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[   44.560000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[   44.570000] cfg80211:   (5250000 KHz - 5330000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[   44.580000] cfg80211:   (5490000 KHz - 5710000 KHz @ 40000 KHz), (N/A, 2700 mBm)
[   44.670000] ar71xx: pll_reg 0xb8050014: 0x13000a44
[   44.670000] eth0: link up (100Mbps/Full duplex)
[   44.670000] br-lan: port 1(eth0) entered forwarding state
[   44.680000] br-lan: port 1(eth0) entered forwarding state
[   45.360000] ar71xx: pll_reg 0xb8050018: 0x13000a44
[   45.360000] eth1: link up (100Mbps/Full duplex)
[   46.330000] device wlan0 entered promiscuous mode
[   46.660000] br-lan: port 2(wlan0) entered forwarding state
[   46.660000] br-lan: port 2(wlan0) entered forwarding state
[   46.680000] br-lan: port 1(eth0) entered forwarding state
[   48.660000] br-lan: port 2(wlan0) entered forwarding state
[   82.480000] ipt_bandwidth: timezone shift of 60 minutes detected, adjusting
[   82.490000]                old minutes west=0, new minutes west=-60
[ 7842.110000] usb 1-1.2: new full-speed USB device number 3 using ehci-platform
[ 8818.510000] usb 1-1.2: USB disconnect, device number 3
root@Gargoyle:~#

Wydaje mi się, że Gargoyle (1.5.8.4) wykrywa ją jako modem Sierra:

root@Gargoyle:~# dmesg | grep modem
[   37.710000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[   38.460000] USB Serial support registered for GSM modem (1-port)
[   38.470000] option: v0.7.2:USB Driver for GSM modems
[   38.520000] USB Serial support registered for Sierra USB modem
[   38.540000] sierra: v.1.7.16:USB Driver for Sierra Wireless USB modems
root@Gargoyle:~# dmesg | grep usb
[    8.690000] usbcore: registered new interface driver usbfs
[    8.690000] usbcore: registered new interface driver hub
[    8.700000] usbcore: registered new device driver usb
[    9.440000] usbcore: registered new interface driver usb-storage
[    9.700000] usb 1-1: new high-speed USB device number 2 using ehci-platform
[   37.710000] usbcore: registered new interface driver cdc_acm
[   37.840000] usbcore: registered new interface driver usblp
[   37.870000] usbcore: registered new interface driver usbserial
[   37.890000] usbcore: registered new interface driver usbserial_generic
[   37.890000] usbserial: USB Serial Driver core
[   38.050000] usbcore: registered new interface driver ums-alauda
[   38.080000] usbcore: registered new interface driver ums-cypress
[   38.100000] usbcore: registered new interface driver ums-datafab
[   38.180000] usbcore: registered new interface driver ums-freecom
[   38.200000] usbcore: registered new interface driver ums-isd200
[   38.230000] usbcore: registered new interface driver ums-jumpshot
[   38.250000] usbcore: registered new interface driver ums-karma
[   38.280000] usbcore: registered new interface driver ums-sddr09
[   38.310000] usbcore: registered new interface driver ums-sddr55
[   38.330000] usbcore: registered new interface driver ums-usbat
[   38.470000] usbcore: registered new interface driver option
[   38.530000] usbcore: registered new interface driver sierra
[ 7842.110000] usb 1-1.2: new full-speed USB device number 3 using ehci-platform
[ 8818.510000] usb 1-1.2: USB disconnect, device number 3
root@Gargoyle:~#

Czy ktoś miał do czynienia z tą kamerką? Na jakim sterowniku działa oraz co zrobić z extrootem (stworzyć nowego hmm ) .?

===========================================
WRT160NL v1 CUR01 with Gargoyle PL  by obsy

TL-MR3420 v2 (MiFi) + E3372h-153 (nie hilink) = Play

2 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,188

Odp: Kamera Trust WB-1100G

Nie, sierra to sterowniki do modemu. cat /proc/bus/usb/devices pokaż.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

3 Odpowiedź przez wojciech_69

  • Zarejestrowany: 2011-03-23
  • Posty: 328

Odp: Kamera Trust WB-1100G

No właśnie, ale jaki modem?

root@Gargoyle:~# cat /proc/bus/usb/devices

T:  Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=480  MxCh= 1
B:  Alloc=  0/800 us ( 0%), #Int=  1, #Iso=  0
D:  Ver= 2.00 Cls=09(hub  ) Sub=00 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=1d6b ProdID=0002 Rev= 3.03
S:  Manufacturer=Linux 3.3.8 ehci_hcd
S:  Product=Generic Platform EHCI Controller
S:  SerialNumber=ehci-platform
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   4 Ivl=256ms

T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=480  MxCh= 4
D:  Ver= 2.00 Cls=09(hub  ) Sub=00 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=1a40 ProdID=0101 Rev= 1.11
S:  Product=USB 2.0 Hub
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   1 Ivl=256ms
root@Gargoyle:~#

Ps. dioda na kamerze cały czas świeci światłem ciągłym.

===========================================
WRT160NL v1 CUR01 with Gargoyle PL  by obsy

TL-MR3420 v2 (MiFi) + E3372h-153 (nie hilink) = Play

4 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,188

Odp: Kamera Trust WB-1100G

Żaden. Obraz zawiera sterowniki do modemów huawei i sierra, one się ładują po prostu i pokazują w logach że istnieją.

Podłącz kamerę bezpośrednio do routera, bo przez ten hub nie działa.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

5 Odpowiedź przez wojciech_69

  • Zarejestrowany: 2011-03-23
  • Posty: 328

Odp: Kamera Trust WB-1100G

logread:

Jan  1 01:00:48 Gargoyle user.notice usb-modeswitch: 1-0:1.0: Manufacturer=Linux_3.3.8_ehci_hcd Product=Generic_Platform_EHCI_Controller Serial=ehci-platform
Jan  1 01:00:48 Gargoyle kern.info kernel: [   48.400000] br-lan: port 2(wlan0) entered forwarding state
Jan 15 12:00:02 Gargoyle user.info sysinit: Loading defaults
Jan 15 12:00:03 Gargoyle user.notice usb-modeswitch: 1-1:1.0: Manufacturer=? Product=USB_camera Serial=?

cat /proc/bus/usb/devices

root@Gargoyle:~# cat /proc/bus/usb/devices

T:  Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=480  MxCh= 1
B:  Alloc=  0/800 us ( 0%), #Int=  0, #Iso=  0
D:  Ver= 2.00 Cls=09(hub  ) Sub=00 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=1d6b ProdID=0002 Rev= 3.03
S:  Manufacturer=Linux 3.3.8 ehci_hcd
S:  Product=Generic Platform EHCI Controller
S:  SerialNumber=ehci-platform
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   4 Ivl=256ms

T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=0c45 ProdID=600d Rev= 1.01
S:  Product=USB camera
C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=81(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=83(I) Atr=03(Int.) MxPS=   1 Ivl=100ms
I:  If#= 0 Alt= 1 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=81(I) Atr=01(Isoc) MxPS= 128 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=83(I) Atr=03(Int.) MxPS=   1 Ivl=100ms
I:  If#= 0 Alt= 2 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=81(I) Atr=01(Isoc) MxPS= 256 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=83(I) Atr=03(Int.) MxPS=   1 Ivl=100ms
I:  If#= 0 Alt= 3 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=81(I) Atr=01(Isoc) MxPS= 384 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=83(I) Atr=03(Int.) MxPS=   1 Ivl=100ms
I:  If#= 0 Alt= 4 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=81(I) Atr=01(Isoc) MxPS= 512 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=83(I) Atr=03(Int.) MxPS=   1 Ivl=100ms
I:  If#= 0 Alt= 5 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=81(I) Atr=01(Isoc) MxPS= 680 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=83(I) Atr=03(Int.) MxPS=   1 Ivl=100ms
I:  If#= 0 Alt= 6 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=81(I) Atr=01(Isoc) MxPS= 800 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=83(I) Atr=03(Int.) MxPS=   1 Ivl=100ms
I:  If#= 0 Alt= 7 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=81(I) Atr=01(Isoc) MxPS= 900 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=83(I) Atr=03(Int.) MxPS=   1 Ivl=100ms
I:  If#= 0 Alt= 8 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=81(I) Atr=01(Isoc) MxPS=1023 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=83(I) Atr=03(Int.) MxPS=   1 Ivl=100ms
root@Gargoyle:~#

Kamera została wykryta, co teraz? Nic nie zainstaluję bo nie mam miejsca - pendrive z extrootem.

===========================================
WRT160NL v1 CUR01 with Gargoyle PL  by obsy

TL-MR3420 v2 (MiFi) + E3372h-153 (nie hilink) = Play

6 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,188

Odp: Kamera Trust WB-1100G

Ta kamera jest obsługiwana przez gspca sonixb

A przez hub Ci nie działa ona, pokazałeś to.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

7 Odpowiedź przez wojciech_69

  • Zarejestrowany: 2011-03-23
  • Posty: 328

Odp: Kamera Trust WB-1100G

Może i głupie pytanie, ale z kąt wiesz że przez sonixb smile ? Po czym to wywnioskowałeś, szukając rozwiązania na forach o tematyce Linuksa wiele wątków wskazywało na inny sterownik, ot taki mały przykład jednego z for:

Trust Spacecam 120 (120 SpaceC@m)
9.04,9.10
0c45:600d
gspca,sn9c102
Skype 2.1.0.47 : works out of the box. lsusb reports: Microdia TwinkleCam USB camera

Czy uważasz, że na innym hubie kamera może być prawidłowo wykrywana? Czym to jest spowodowane, napięciem? W tym momencie bez extroota (hub + pendrive) nie jestem w stanie nawet jej uruchomić, wiec hub jest wymagany.

I co z dotychczasowym extrootem, jest do uratowania (tryb failsafe), co mogło zostać tam namieszane Twoim zdaniem, że router nie chciał się uruchomić?

===========================================
WRT160NL v1 CUR01 with Gargoyle PL  by obsy

TL-MR3420 v2 (MiFi) + E3372h-153 (nie hilink) = Play

8 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,188

Odp: Kamera Trust WB-1100G

Po identyfikatorach magistrali usb i po źródłach kernela. sn9c102 obsługuje

MODULE_ALIAS("usb:v0C45p6024d*dc*dsc*dp*icFFisc*ip*");
MODULE_ALIAS("usb:v0C45p6025d*dc*dsc*dp*icFFisc*ip*");
MODULE_ALIAS("usb:v0C45p602Bd*dc*dsc*dp*icFFisc*ip*");
MODULE_ALIAS("usb:v0C45p6030d*dc*dsc*dp*icFFisc*ip*");
MODULE_ALIAS("usb:v0C45p6082d*dc*dsc*dp*icFFisc*ip*");

Szczerze to nie wiem. Miałem też kamery które za chiny nie chciały przez huba usb działać i już.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

9 Odpowiedź przez wojciech_69

  • Zarejestrowany: 2011-03-23
  • Posty: 328

Odp: Kamera Trust WB-1100G

Zmieniłem hub-a z esperanza EA116 na LogiLink UA0071 i kamerka jest wykrywana równolegle z pendrive (extroot).

root@Gargoyle:~# cat /proc/bus/usb/devices

T:  Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=480  MxCh= 1
B:  Alloc=  2/800 us ( 0%), #Int=  2, #Iso=  3
D:  Ver= 2.00 Cls=09(hub  ) Sub=00 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=1d6b ProdID=0002 Rev= 3.03
S:  Manufacturer=Linux 3.3.8 ehci_hcd
S:  Product=Generic Platform EHCI Controller
S:  SerialNumber=ehci-platform
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   4 Ivl=256ms

T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=480  MxCh= 4
D:  Ver= 2.00 Cls=09(hub  ) Sub=00 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=1a40 ProdID=0101 Rev= 1.11
S:  Product=USB 2.0 Hub
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   1 Ivl=256ms

T:  Bus=01 Lev=02 Prnt=02 Port=01 Cnt=01 Dev#=  4 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=0c45 ProdID=600d Rev= 1.01
S:  Product=USB camera
C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=sonixb
E:  Ad=81(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=83(I) Atr=03(Int.) MxPS=   1 Ivl=100ms
I:  If#= 0 Alt= 1 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=sonixb
E:  Ad=81(I) Atr=01(Isoc) MxPS= 128 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=83(I) Atr=03(Int.) MxPS=   1 Ivl=100ms
I:  If#= 0 Alt= 2 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=sonixb
E:  Ad=81(I) Atr=01(Isoc) MxPS= 256 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=83(I) Atr=03(Int.) MxPS=   1 Ivl=100ms
I:  If#= 0 Alt= 3 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=sonixb
E:  Ad=81(I) Atr=01(Isoc) MxPS= 384 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=83(I) Atr=03(Int.) MxPS=   1 Ivl=100ms
I:  If#= 0 Alt= 4 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=sonixb
E:  Ad=81(I) Atr=01(Isoc) MxPS= 512 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=83(I) Atr=03(Int.) MxPS=   1 Ivl=100ms
I:  If#= 0 Alt= 5 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=sonixb
E:  Ad=81(I) Atr=01(Isoc) MxPS= 680 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=83(I) Atr=03(Int.) MxPS=   1 Ivl=100ms
I:* If#= 0 Alt= 6 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=sonixb
E:  Ad=81(I) Atr=01(Isoc) MxPS= 800 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=83(I) Atr=03(Int.) MxPS=   1 Ivl=100ms
I:  If#= 0 Alt= 7 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=sonixb
E:  Ad=81(I) Atr=01(Isoc) MxPS= 900 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=83(I) Atr=03(Int.) MxPS=   1 Ivl=100ms
I:  If#= 0 Alt= 8 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=sonixb
E:  Ad=81(I) Atr=01(Isoc) MxPS=1023 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=83(I) Atr=03(Int.) MxPS=   1 Ivl=100ms

T:  Bus=01 Lev=02 Prnt=02 Port=02 Cnt=02 Dev#=  3 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=13fe ProdID=3800 Rev= 1.00
S:  Manufacturer=
S:  Product=Patriot Memory
S:  SerialNumber=07B2170157340A92
C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=300mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
root@Gargoyle:~#

(kamera cały czas podłączona, świeci dioda informująca o jej działaniu/podłączeniu)

Zainstalowałem:

opkg install kmod-usb-core kmod-usb2 kmod-video-core
opkg install kmod-video-gspca-core kmod-video-gspca-sonixb

po czym dioda na kamerca zgasła...

dmesg

[  482.670000] usb 1-1.2: new full-speed USB device number 4 using ehci-platform
[  675.400000] Linux video capture interface: v2.00
[  854.610000] gspca_main: v2.14.0 registered
[  854.670000] gspca_main: sonixb-2.14.0 probing 0c45:600d
[  854.680000] input: sonixb as /devices/platform/ehci-platform/usb1/1-1/1-1.2/input/input0
[  854.690000] usbcore: registered new interface driver sonixb
root@Gargoyle:~#

zainstalowałem motion po czym wyłączyłem:

stream_localhost off
output_pictures off

aha, urządzenie zostało utworzone oczywiście:

root@Gargoyle:~# ls -al /dev/video*
crw-r--r--    1 root     root       81,   0 Jan 23 08:36 /dev/video0
root@Gargoyle:~#

wpisuję # motion i otrzymuję komunikat:

root@Gargoyle:~# motion
[0] [NTC] [ALL] conf_load: Processing thread 0 - config file /etc/motion.conf
[0] [ALR] [ALL] conf_cmdparse: Unknown config option "ffmpeg_output_movies"
[0] [ALR] [ALL] conf_cmdparse: Unknown config option "ffmpeg_output_debug_movies"
[0] [ALR] [ALL] conf_cmdparse: Unknown config option "ffmpeg_timelapse"
[0] [ALR] [ALL] conf_cmdparse: Unknown config option "ffmpeg_timelapse_mode"
[0] [ALR] [ALL] conf_cmdparse: Unknown config option "ffmpeg_bps"
[0] [ALR] [ALL] conf_cmdparse: Unknown config option "ffmpeg_variable_bitrate"
[0] [ALR] [ALL] conf_cmdparse: Unknown config option "ffmpeg_video_codec"
[0] [ALR] [ALL] conf_cmdparse: Unknown config option "ffmpeg_deinterlace"
[0] [ALR] [ALL] conf_cmdparse: Unknown config option "sdl_threadnr"
[0] [ALR] [ALL] conf_cmdparse: Unknown config option "movie_filename"
[0] [ALR] [ALL] conf_cmdparse: Unknown config option "timelapse_filename"
[0] [NTC] [ALL] motion_startup: Motion trunkREV528 Started
[0] [NTC] [ALL] motion_startup: Logging to syslog
[0] [NTC] [ALL] motion_startup: Using log type (ALL) log level (NTC)
[0] [NTC] [ALL] become_daemon: Motion going to daemon mode
[0] [NTC] [ALL] create_path: creating directory /var/run/motion
root@Gargoyle:~#

w tym momencie dioda zapala się, lecz po zalogowaniu na adres: http://router:8081 nic mi się nie wyświetla (na Chrome oraz FF).

Podejrzewam, że coś mam z konfiguracją motion albo muszę doinstalować/skonfigurować ffmpeg ?

===========================================
WRT160NL v1 CUR01 with Gargoyle PL  by obsy

TL-MR3420 v2 (MiFi) + E3372h-153 (nie hilink) = Play

10 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,188

Odp: Kamera Trust WB-1100G

Nie, samo ma działać. Zainstaluj fswebcam i zobacz czy w ogóle pobiera obrazki.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

11 Odpowiedź przez wojciech_69

  • Zarejestrowany: 2011-03-23
  • Posty: 328

Odp: Kamera Trust WB-1100G

root@Gargoyle:~# fswebcam /tmp/a.jpg
--- Opening /dev/video0...
Trying source module v4l2...
/dev/video0 opened.
No input was specified, using the first.
Adjusting resolution from 384x288 to 176x144.
Error requesting buffers for memory map.
VIDIOC_REQBUFS: Device or resource busy
Unable to use mmap. Using read instead.
--- Capturing frame...
Unable to read a frame.
read: Invalid argument
No frames captured.
root@Gargoyle:~#

zła rozdzielczość kamery? hmm

===========================================
WRT160NL v1 CUR01 with Gargoyle PL  by obsy

TL-MR3420 v2 (MiFi) + E3372h-153 (nie hilink) = Play

12 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,188

Odp: Kamera Trust WB-1100G

Rozdzielczość możesz podać z linii poleceń. Ale nie potrafi odczytać tej kamery...

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

13 Odpowiedź przez wojciech_69

  • Zarejestrowany: 2011-03-23
  • Posty: 328

Odp: Kamera Trust WB-1100G

Czy da się coś z tym zrobić, czy jednym słowem - ta kamerka nie działa pod Gargulcem?

===========================================
WRT160NL v1 CUR01 with Gargoyle PL  by obsy

TL-MR3420 v2 (MiFi) + E3372h-153 (nie hilink) = Play

14 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,188

Odp: Kamera Trust WB-1100G

Poszukaj po sieci, może ktoś znalazł na nią rozwiązanie.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

15 Odpowiedź przez wojciech_69

  • Zarejestrowany: 2011-03-23
  • Posty: 328

Odp: Kamera Trust WB-1100G

Tak wyglądają logi:

Jan 23 09:03:31 Gargoyle user.notice syslog: [0] [NTC] [ALL] conf_load: Processing thread 0 - config file /etc/motion.conf
Jan 23 09:03:31 Gargoyle user.alert syslog: [0] [ALR] [ALL] conf_cmdparse: Unknown config option "ffmpeg_output_movies"
Jan 23 09:03:31 Gargoyle user.alert syslog: [0] [ALR] [ALL] conf_cmdparse: Unknown config option "ffmpeg_output_debug_movies"
Jan 23 09:03:31 Gargoyle user.alert syslog: [0] [ALR] [ALL] conf_cmdparse: Unknown config option "ffmpeg_timelapse"
Jan 23 09:03:31 Gargoyle user.alert syslog: [0] [ALR] [ALL] conf_cmdparse: Unknown config option "ffmpeg_timelapse_mode"
Jan 23 09:03:31 Gargoyle user.alert syslog: [0] [ALR] [ALL] conf_cmdparse: Unknown config option "ffmpeg_bps"
Jan 23 09:03:31 Gargoyle user.alert syslog: [0] [ALR] [ALL] conf_cmdparse: Unknown config option "ffmpeg_variable_bitrate"
Jan 23 09:03:31 Gargoyle user.alert syslog: [0] [ALR] [ALL] conf_cmdparse: Unknown config option "ffmpeg_video_codec"
Jan 23 09:03:31 Gargoyle user.alert syslog: [0] [ALR] [ALL] conf_cmdparse: Unknown config option "ffmpeg_deinterlace"
Jan 23 09:03:31 Gargoyle user.alert syslog: [0] [ALR] [ALL] conf_cmdparse: Unknown config option "sdl_threadnr"
Jan 23 09:03:31 Gargoyle user.alert syslog: [0] [ALR] [ALL] conf_cmdparse: Unknown config option "movie_filename"
Jan 23 09:03:31 Gargoyle user.alert syslog: [0] [ALR] [ALL] conf_cmdparse: Unknown config option "timelapse_filename"
Jan 23 09:03:31 Gargoyle user.notice syslog: [0] [NTC] [ALL] motion_startup: Motion trunkREV528 Started
Jan 23 09:03:31 Gargoyle user.notice syslog: [0] [NTC] [ALL] motion_startup: Logging to syslog
Jan 23 09:03:31 Gargoyle user.notice syslog: [0] [NTC] [ALL] motion_startup: Using log type (ALL) log level (NTC)
Jan 23 09:03:31 Gargoyle user.notice syslog: [0] [NTC] [ALL] become_daemon: Motion going to daemon mode
Jan 23 09:03:31 Gargoyle user.notice syslog: [0] [NTC] [ALL] create_path: creating directory /var/run/motion
Jan 23 09:03:31 Gargoyle user.notice syslog: [0] [NTC] [ALL] become_daemon: Created process id file /var/run/motion/motion.pid. Process ID is 2674
Jan 23 09:03:31 Gargoyle user.notice syslog: [0] [NTC] [ALL] motion_startup: Motion running as daemon process
Jan 23 09:03:31 Gargoyle user.notice syslog: [0] [NTC] [ALL] main: Thread 1 is from /etc/motion.conf
Jan 23 09:03:31 Gargoyle user.notice syslog: [0] [NTC] [ALL] main: Thread 1 is device: /dev/video0 input -1
Jan 23 09:03:31 Gargoyle user.notice syslog: [0] [NTC] [ALL] main: Stream port 8081
Jan 23 09:03:31 Gargoyle user.notice syslog: [0] [NTC] [ALL] main: Waiting for threads to finish, pid: 2674
Jan 23 09:03:31 Gargoyle user.notice syslog: [1] [NTC] [ALL] motion_init: Thread 1 started
Jan 23 09:03:31 Gargoyle user.notice syslog: [1] [NTC] [VID] vid_v4lx_start: Using videodevice /dev/video0 and input -1
Jan 23 09:03:31 Gargoyle user.notice syslog: [1] [NTC] [VID] v4l2_get_capability:  ------------------------ cap.driver: "sonixb" cap.card: "USB camera" cap.bus_info: "usb-ehci-platform-1.2" cap.capabilities=0x05000001 ------------------------
Jan 23 09:03:31 Gargoyle user.notice syslog: [1] [NTC] [VID] v4l2_get_capability: - VIDEO_CAPTURE
Jan 23 09:03:31 Gargoyle user.notice syslog: [1] [NTC] [VID] v4l2_get_capability: - READWRITE
Jan 23 09:03:31 Gargoyle user.notice syslog: [1] [NTC] [VID] v4l2_get_capability: - STREAMING
Jan 23 09:03:31 Gargoyle user.notice syslog: [1] [NTC] [VID] v4l2_select_input: name = "sonixb", type 0x00000002, status 00000000
Jan 23 09:03:31 Gargoyle user.notice syslog: [1] [NTC] [VID] v4l2_select_input: - CAMERA
Jan 23 09:03:31 Gargoyle user.warn syslog: [1] [WRN] [VID] v4l2_select_input: Device doesn't support VIDIOC_G_STD
Jan 23 09:03:31 Gargoyle user.notice syslog: [1] [NTC] [VID] v4l2_set_pix_format: Config palette index 17 (YU12) doesn't work.
Jan 23 09:03:31 Gargoyle user.notice syslog: [1] [NTC] [VID] v4l2_set_pix_format: Supported palettes:
Jan 23 09:03:31 Gargoyle user.notice syslog: [1] [NTC] [VID] v4l2_set_pix_format: (0) S910 (S910)
Jan 23 09:03:31 Gargoyle user.notice syslog: [1] [NTC] [VID] vid_v4lx_start: Using V4L2
Jan 23 09:03:31 Gargoyle user.notice syslog: [1] [NTC] [ALL] image_ring_resize: Resizing pre_capture buffer to 1 items
Jan 23 09:03:31 Gargoyle user.notice syslog: [1] [NTC] [STR] http_bindsock: motion-stream testing : IPV4 addr: 0.0.0.0 port: 8081
Jan 23 09:03:31 Gargoyle user.notice syslog: [1] [NTC] [STR] http_bindsock: motion-stream Bound : IPV4 addr: 0.0.0.0 port: 8081
Jan 23 09:03:31 Gargoyle user.notice syslog: [1] [NTC] [ALL] motion_init: Started motion-stream server in port 8081
Jan 23 09:13:40 Gargoyle user.notice syslog: [1] [NTC] [EVT] event_new_video FPS 2
Jan 23 09:13:40 Gargoyle user.notice syslog: [1] [NTC] [ALL] motion_detected: Motion detected - starting event 1
Jan 23 09:17:20 Gargoyle user.notice syslog: [1] [NTC] [EVT] event_new_video FPS 2
Jan 23 09:17:20 Gargoyle user.notice syslog: [1] [NTC] [ALL] motion_detected: Motion detected - starting event 2
Jan 23 09:20:29 Gargoyle user.notice syslog: [1] [NTC] [EVT] event_new_video FPS 2
Jan 23 09:20:29 Gargoyle user.notice syslog: [1] [NTC] [ALL] motion_detected: Motion detected - starting event 3
Jan 23 09:25:14 Gargoyle user.notice syslog: [1] [NTC] [EVT] event_new_video FPS 2
Jan 23 09:25:14 Gargoyle user.notice syslog: [1] [NTC] [ALL] motion_detected: Motion detected - starting event 4
Jan 23 09:28:00 Gargoyle user.notice syslog: [1] [NTC] [EVT] event_new_video FPS 2
Jan 23 09:28:00 Gargoyle user.notice syslog: [1] [NTC] [ALL] motion_detected: Motion detected - starting event 5
Jan 23 09:33:03 Gargoyle user.notice syslog: [1] [NTC] [EVT] event_new_video FPS 2
Jan 23 09:33:03 Gargoyle user.notice syslog: [1] [NTC] [ALL] motion_detected: Motion detected - starting event 6
Jan 23 09:37:19 Gargoyle user.notice syslog: [1] [NTC] [EVT] event_new_video FPS 2
Jan 23 09:37:19 Gargoyle user.notice syslog: [1] [NTC] [ALL] motion_detected: Motion detected - starting event 7
root@Gargoyle:~#

===========================================
WRT160NL v1 CUR01 with Gargoyle PL  by obsy

TL-MR3420 v2 (MiFi) + E3372h-153 (nie hilink) = Play