Mam modem Huawei E353 u2 z kartą Aero2 wrzucony do TL-MR3420 z gargoyle pl najnowszym od Cezarego i ciągle są jakieś problemy z tym modemem, extroot działał niestabilnie więc go wyłączyłem. Ale teraz trafiają się momenty gdy nie chce nic iść przez niego (mam ustawiony multiwan na wanie i 3g) i wywaliło mi takie ciekawostki:

dmesg

io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
console [ttyS0] enabled, bootconsole disabled
Atheros AR71xx SPI Controller driver version 0.2.4
m25p80 spi0.0: s25sl032a (4096 Kbytes)
spi0.0: searching for MyLoader partition table at offset 0x10000
spi0.0: searching for MyLoader partition table at offset 0x20000
spi0.0: searching for MyLoader partition table at offset 0x30000
spi0.0: searching for MyLoader partition table at offset 0x40000
spi0.0: no MyLoader partition table found
Searching for RedBoot partition table in spi0.0 at offset 0x3e0000
Searching for RedBoot partition table in spi0.0 at offset 0x3f0000
No RedBoot partition table detected in spi0.0
Creating 5 MTD partitions on "spi0.0":
0x000000000000-0x000000020000 : "u-boot"
0x000000020000-0x000000140000 : "kernel"
0x000000140000-0x0000003f0000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=390000, len=60000
0x000000390000-0x0000003f0000 : "rootfs_data"
0x0000003f0000-0x000000400000 : "art"
0x000000020000-0x0000003f0000 : "firmware"
ag71xx_mdio: probed
eth0: Atheros AG71xx at 0xba000000, irq 5
eth0: Found an AR7240 built-in switch
eth1: Atheros AG71xx at 0xb9000000, irq 4
eth1: connected to PHY at ag71xx-mdio:04 [uid=004dd041, driver=Generic PHY]
Atheros AR71xx hardware watchdog driver version 0.1.0
ar71xx-wdt: timeout=15 secs (max=21)
TCP westwood registered
NET: Registered protocol family 17
Bridge firewalling registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 136k freed
Please be patient, while OpenWrt loads ...
input: gpio-buttons as /devices/platform/gpio-buttons/input/input0
Button Hotplug driver version 0.3.1
Registered led device: tl-mr3420:green:system
Registered led device: tl-mr3420:green:qss
Registered led device: tl-mr3420:green:3g
eth0: link up (1000Mbps/Full duplex)
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ar71xx-ehci ar71xx-ehci: Atheros AR91xx built-in EHCI controller
ar71xx-ehci ar71xx-ehci: new USB bus registered, assigned bus number 1
ar71xx-ehci ar71xx-ehci: irq 3, io mem 0x1b000000
ar71xx-ehci ar71xx-ehci: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb 1-1: new high speed USB device using ar71xx-ehci and address 2
usb 1-1: configuration #1 chosen from 1 choice
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
scsi1 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
scsi 0:0:0:0: CD-ROM            HUAWEI   Mass Storage     2.31 PQ: 0 ANSI: 2
scsi 1:0:0:0: Direct-Access     HUAWEI   TF CARD Storage       PQ: 0 ANSI: 2
usb-storage: device scan complete
sd 1:0:0:0: [sda] 248320 512-byte logical blocks: (127 MB/121 MiB)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Mode Sense: 0f 0e 00 00
sd 1:0:0:0: [sda] Assuming drive cache: write through
usb-storage: device scan complete
sd 1:0:0:0: [sda] Assuming drive cache: write through
sda: sda1 sda2
sd 1:0:0:0: [sda] Assuming drive cache: write through
sd 1:0:0:0: [sda] Attached SCSI removable disk
usb 1-1: usbfs: process 322 (usb_modeswitch) did not claim interface 0 before use
usb 1-1: USB disconnect, address 2
usb 1-1: new high speed USB device using ar71xx-ehci and address 3
usb 1-1: configuration #1 chosen from 1 choice
scsi2 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
scsi 2:0:0:0: Direct-Access     HUAWEI   TF CARD Storage       PQ: 0 ANSI: 2
usb-storage: device scan complete
sd 2:0:0:0: [sda] 248320 512-byte logical blocks: (127 MB/121 MiB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 0f 0e 00 00
sd 2:0:0:0: [sda] Assuming drive cache: write through
sd 2:0:0:0: [sda] Assuming drive cache: write through
sda: sda1 sda2
sd 2:0:0:0: [sda] Assuming drive cache: write through
sd 2:0:0:0: [sda] Attached SCSI removable disk
mini_fo: using base directory: /
mini_fo: using storage directory: /overlay
eth0: link down
eth0: link up (1000Mbps/Full duplex)
device eth0 entered promiscuous mode
br-lan: port 1(eth0) entering forwarding state
Compat-wireless backport release: compat-wireless-2011-11-29
Backport based on wireless-testing.git master-2011-12-01
eth1: link up (100Mbps/Full duplex)
cfg80211: Calling CRDA to update world regulatory domain
cfg80211: World regulatory domain updated:
cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:     (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211:     (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211:     (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:     (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
PCI: Setting latency timer of device 0000:00:00.0 to 64
ath: EEPROM regdomain: 0x0
ath: EEPROM indicates default country code should be used
ath: doing EEPROM country->regdmn map search
ath: country maps to regdmn code: 0x3a
ath: Country alpha2 being used: US
ath: Regpair used: 0x3a
ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
Registered led device: ath9k-phy0
ieee80211 phy0: Atheros AR9287 Rev:2 mem=0xb0000000, irq=48
cfg80211: Calling CRDA for country: US
cfg80211: Regulatory domain changed to country: US
cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
cfg80211:     (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
cfg80211:     (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:     (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:     (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:     (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
PPP generic driver version 2.4.2
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
ip_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 24
nf_conntrack version 0.5.0 (462 buckets, 1848 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
xt_time: kernel timezone is -0000
        Hooked IMQ after mangle on PREROUTING
        Hooked IMQ after nat on POSTROUTING
IMQ driver loaded successfully.
ip_set version 4 loaded
usbcore: registered new interface driver cdc_acm
cdc_acm: v0.26:USB Abstract Control Model driver for USB modems and ISDN adapters
usbcore: registered new interface driver usbserial
USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
usbserial: USB Serial Driver core
USB Serial support registered for GSM modem (1-port)
option 1-1:1.0: GSM modem (1-port) converter detected
usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0
option 1-1:1.1: GSM modem (1-port) converter detected
usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1
option 1-1:1.2: GSM modem (1-port) converter detected
usb 1-1: GSM modem (1-port) converter now attached to ttyUSB2
usbcore: registered new interface driver option
option: v0.7.2:USB Driver for GSM modems
USB Serial support registered for Sierra USB modem
usbcore: registered new interface driver sierra
sierra: v.1.3.8:USB Driver for Sierra Wireless USB modems
cfg80211: Calling CRDA for country: PL
cfg80211: Regulatory domain changed to country: PL
cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211:     (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
cfg80211:     (5170000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)
cfg80211:     (5250000 KHz - 5330000 KHz @ 40000 KHz), (N/A, 2000 mBm)
cfg80211:     (5490000 KHz - 5710000 KHz @ 40000 KHz), (N/A, 2700 mBm)
ipt_bandwidth: timezone shift of 120 minutes detected, adjusting
               old minutes west=0, new minutes west=-120
ar71xx-wdt: enabling watchdog timer
eth1: link down
eth1: link up (100Mbps/Full duplex)
eth1: link down
eth1: link up (100Mbps/Full duplex)
------------[ cut here ]------------
WARNING: at drivers/usb/serial/usb-serial.c:441 0x80fd86fc()
Modules linked in: sierra option usbserial cdc_acm ledtrig_usbdev ipt_SET ipt_set ip_set_setlist ip_set_portmap ip_set_nethash ip_set_macipmap ip_set_iptreemap ip_set_iptree ip_set_ipportnethash ip_set_ipportiphash ip_set_ipporthash ip_set_ipmap ip_set_iphash ip_set xt_IMQ imq ipt_weburl ipt_webmon ipt_timerange nf_nat_tftp nf_conntrack_tftp nf_nat_irc nf_conntrack_irc nf_nat_ftp nf_conntrack_ftp xt_iprange xt_HL xt_hl xt_MARK ipt_ECN xt_CLASSIFY xt_time xt_tcpmss xt_statistic xt_mark xt_length ipt_ecn xt_DSCP xt_dscp xt_string xt_layer7 ipt_bandwidth ipt_REDIRECT ipt_NETMAP ipt_MASQUERADE iptable_nat nf_nat xt_CONNMARK xt_recent xt_helper xt_conntrack xt_connmark xt_connbytes xt_NOTRACK iptable_raw xt_state nf_conntrack_ipv4 nf_defrag_ipv4 nf_conntrack pppoe pppox ipt_REJECT xt_TCPMSS ipt_LOG xt_comment xt_multiport xt_mac xt_limit iptable_mangle iptable_filter ip_tables xt_tcpudp x_tables tun ppp_async ppp_generic slhc vfat fat ath9k ath9k_common ath9k_hw ath nls_iso8859_1 nls_cp437 mac80211 ts_fsm ts_bm ts_kmp crc_ccitt cfg80211 compat arc4 aes_generic deflate ecb cbc usb_storage ehci_hcd sd_mod ext2 usbcore scsi_mod nls_base mbcache leds_gpio button_hotplug gpio_buttons input_polldev input_core
Call Trace:[<8007ec1c>] 0x8007ec1c
[<800692b0>] 0x800692b0
[<800692b0>] 0x800692b0
[<8007db28>] 0x8007db28
[<80fd86fc>] 0x80fd86fc
[<80fd86fc>] 0x80fd86fc
[<8018a0f4>] 0x8018a0f4
[<8018874c>] 0x8018874c
[<8018c45c>] 0x8018c45c
[<8018ce78>] 0x8018ce78
[<80fd8c64>] 0x80fd8c64
[<80184dd4>] 0x80184dd4
[<800931cc>] 0x800931cc
[<80078608>] 0x80078608
[<801850e0>] 0x801850e0
[<800db0dc>] 0x800db0dc
[<800d7844>] 0x800d7844
[<800e8200>] 0x800e8200
[<8007fd4c>] 0x8007fd4c
[<80081584>] 0x80081584
[<80081a60>] 0x80081a60
[<80062544>] 0x80062544

---[ end trace f8a023d9845c5646 ]---
root@Gargoyle:~$

What the f...? Na extrocie też czasem były takie dziwne cyferki i nie dało się nic zapisać na kartę (...)