1 Temat przez pepe_lodz (edytowany przez pepe_lodz 2012-03-30 15:43:45)

  • Zarejestrowany: 2010-06-18
  • Posty: 974

Temat: TL-WR1043ND backfire openwrt i problem z polaczeniem 3G modem E1820

Witam
Wgralem do swojego tplinka backfire z luci. Chcialem ustawic aby miec lacze wan z kablowego internetu a #g jako zapasowe. Jednak mam problem ze nie wiem co jest nie tak, gdyz modem niby w logread wyglada jakby sie laczyl z internetem ale nie laczy sie. Modem to Huawei E1820. Dioda na nim mruga caly czas na niebiesko a powinna sie zaswiecic niebieskim jasnym kolorem gdy sie polaczy. Daje polecenie ifup 3g i nic. Stworzylem dodatkowy interface o nazwie 3G tak jak WAN i LAN. W nim ustawilem parametry dla polaczenia 3G , wybralem USB0 , apn dla plusa... tak wyglada logread:

root@OpenWrt:~# logread
Mar 30 14:34:01 OpenWrt local2.info chat[11907]: send (ATE1^M)
Mar 30 14:34:02 OpenWrt local2.info chat[11907]: expect (OK)
Mar 30 14:34:02 OpenWrt local2.info chat[11907]: ^M
Mar 30 14:34:02 OpenWrt local2.info chat[11907]: ATE1^M^M
Mar 30 14:34:02 OpenWrt local2.info chat[11907]: OK
Mar 30 14:34:02 OpenWrt local2.info chat[11907]:  -- got it
Mar 30 14:34:02 OpenWrt local2.info chat[11907]: send (AT+CGDCONT=1,"IP","internet"^M)
Mar 30 14:34:02 OpenWrt local2.info chat[11907]: timeout set to 30 seconds
Mar 30 14:34:02 OpenWrt local2.info chat[11907]: expect (OK)
Mar 30 14:34:02 OpenWrt local2.info chat[11907]: ^M
Mar 30 14:34:02 OpenWrt local2.info chat[11907]: AT+CGDCONT=1,"IP","internet"^M^M
Mar 30 14:34:02 OpenWrt local2.info chat[11907]: OK
Mar 30 14:34:02 OpenWrt local2.info chat[11907]:  -- got it
Mar 30 14:34:02 OpenWrt local2.info chat[11907]: send (ATD*99***1#^M)
Mar 30 14:34:02 OpenWrt local2.info chat[11907]: expect (CONNECT)
Mar 30 14:34:02 OpenWrt local2.info chat[11907]: ^M
Mar 30 14:34:02 OpenWrt local2.info chat[11907]: ATD*99***1#^M^M
Mar 30 14:34:02 OpenWrt local2.info chat[11907]: CONNECT
Mar 30 14:34:02 OpenWrt local2.info chat[11907]:  -- got it
Mar 30 14:34:02 OpenWrt local2.info chat[11907]: send ( ^M)
Mar 30 14:34:02 OpenWrt daemon.info pppd[11501]: Serial connection established.
Mar 30 14:34:02 OpenWrt daemon.info pppd[11501]: Using interface 3g-3g
Mar 30 14:34:02 OpenWrt daemon.notice pppd[11501]: Connect: 3g-3g <--> /dev/ttyUSB0
Mar 30 14:34:03 OpenWrt daemon.info pppd[11501]: CHAP authentication succeeded
Mar 30 14:34:03 OpenWrt daemon.notice pppd[11501]: CHAP authentication succeeded
Mar 30 14:34:04 OpenWrt daemon.info pppd[11501]: Hangup (SIGHUP)
Mar 30 14:34:04 OpenWrt daemon.notice pppd[11501]: Modem hangup
Mar 30 14:34:04 OpenWrt daemon.notice pppd[11501]: Connection terminated.
Mar 30 14:34:37 OpenWrt local2.info chat[12110]: abort on (BUSY)
Mar 30 14:34:37 OpenWrt local2.info chat[12110]: abort on (NO CARRIER)
Mar 30 14:34:37 OpenWrt local2.info chat[12110]: abort on (ERROR)
Mar 30 14:34:37 OpenWrt local2.info chat[12110]: report (CONNECT)
Mar 30 14:34:37 OpenWrt local2.info chat[12110]: timeout set to 10 seconds
Mar 30 14:34:37 OpenWrt local2.info chat[12110]: send (AT&F^M)
Mar 30 14:34:37 OpenWrt local2.info chat[12110]: expect (OK)
Mar 30 14:34:37 OpenWrt local2.info chat[12110]: AT&F^M^M
Mar 30 14:34:37 OpenWrt local2.info chat[12110]: OK
Mar 30 14:34:37 OpenWrt local2.info chat[12110]:  -- got it
Mar 30 14:34:37 OpenWrt local2.info chat[12110]: send (ATE1^M)
Mar 30 14:34:37 OpenWrt local2.info chat[12110]: expect (OK)
Mar 30 14:34:37 OpenWrt local2.info chat[12110]: ^M
Mar 30 14:34:37 OpenWrt local2.info chat[12110]: ATE1^M^M
Mar 30 14:34:37 OpenWrt local2.info chat[12110]: OK
Mar 30 14:34:37 OpenWrt local2.info chat[12110]:  -- got it
Mar 30 14:34:37 OpenWrt local2.info chat[12110]: send (AT+CGDCONT=1,"IP","internet"^M)
Mar 30 14:34:37 OpenWrt local2.info chat[12110]: timeout set to 30 seconds
Mar 30 14:34:37 OpenWrt local2.info chat[12110]: expect (OK)
Mar 30 14:34:37 OpenWrt local2.info chat[12110]: ^M
Mar 30 14:34:37 OpenWrt local2.info chat[12110]: AT+CGDCONT=1,"IP","internet"^M^M
Mar 30 14:34:37 OpenWrt local2.info chat[12110]: OK
Mar 30 14:34:37 OpenWrt local2.info chat[12110]:  -- got it
Mar 30 14:34:37 OpenWrt local2.info chat[12110]: send (ATD*99***1#^M)
Mar 30 14:34:37 OpenWrt local2.info chat[12110]: expect (CONNECT)
Mar 30 14:34:37 OpenWrt local2.info chat[12110]: ^M
Mar 30 14:34:37 OpenWrt local2.info chat[12110]: ATD*99***1#^M^M
Mar 30 14:34:37 OpenWrt local2.info chat[12110]: CONNECT
Mar 30 14:34:37 OpenWrt local2.info chat[12110]:  -- got it
Mar 30 14:34:37 OpenWrt local2.info chat[12110]: send ( ^M)
Mar 30 14:34:37 OpenWrt daemon.info pppd[11501]: Serial connection established.
Mar 30 14:34:37 OpenWrt daemon.info pppd[11501]: Using interface 3g-3g
Mar 30 14:34:37 OpenWrt daemon.notice pppd[11501]: Connect: 3g-3g <--> /dev/ttyUSB0
Mar 30 14:34:38 OpenWrt daemon.info pppd[11501]: CHAP authentication succeeded
Mar 30 14:34:38 OpenWrt daemon.notice pppd[11501]: CHAP authentication succeeded
Mar 30 14:34:40 OpenWrt daemon.info pppd[11501]: Hangup (SIGHUP)
Mar 30 14:34:40 OpenWrt daemon.notice pppd[11501]: Modem hangup
Mar 30 14:34:40 OpenWrt daemon.notice pppd[11501]: Connection terminated.
Mar 30 14:35:12 OpenWrt local2.info chat[12330]: abort on (BUSY)
Mar 30 14:35:12 OpenWrt local2.info chat[12330]: abort on (NO CARRIER)
Mar 30 14:35:12 OpenWrt local2.info chat[12330]: abort on (ERROR)
Mar 30 14:35:12 OpenWrt local2.info chat[12330]: report (CONNECT)
Mar 30 14:35:12 OpenWrt local2.info chat[12330]: timeout set to 10 seconds
Mar 30 14:35:12 OpenWrt local2.info chat[12330]: send (AT&F^M)
Mar 30 14:35:12 OpenWrt local2.info chat[12330]: expect (OK)
Mar 30 14:35:12 OpenWrt local2.info chat[12330]: AT&F^M^M
Mar 30 14:35:12 OpenWrt local2.info chat[12330]: OK
Mar 30 14:35:12 OpenWrt local2.info chat[12330]:  -- got it
Mar 30 14:35:12 OpenWrt local2.info chat[12330]: send (ATE1^M)
Mar 30 14:35:12 OpenWrt local2.info chat[12330]: expect (OK)
Mar 30 14:35:12 OpenWrt local2.info chat[12330]: ^M
Mar 30 14:35:12 OpenWrt local2.info chat[12330]: ATE1^M^M
Mar 30 14:35:12 OpenWrt local2.info chat[12330]: OK
Mar 30 14:35:12 OpenWrt local2.info chat[12330]:  -- got it
Mar 30 14:35:12 OpenWrt local2.info chat[12330]: send (AT+CGDCONT=1,"IP","internet"^M)
Mar 30 14:35:13 OpenWrt local2.info chat[12330]: timeout set to 30 seconds
Mar 30 14:35:13 OpenWrt local2.info chat[12330]: expect (OK)
Mar 30 14:35:13 OpenWrt local2.info chat[12330]: ^M
Mar 30 14:35:13 OpenWrt local2.info chat[12330]: AT+CGDCONT=1,"IP","internet"^M^M
Mar 30 14:35:13 OpenWrt local2.info chat[12330]: OK
Mar 30 14:35:13 OpenWrt local2.info chat[12330]:  -- got it
Mar 30 14:35:13 OpenWrt local2.info chat[12330]: send (ATD*99***1#^M)
Mar 30 14:35:13 OpenWrt local2.info chat[12330]: expect (CONNECT)
Mar 30 14:35:13 OpenWrt local2.info chat[12330]: ^M
Mar 30 14:35:13 OpenWrt local2.info chat[12330]: ATD*99***1#^M^M
Mar 30 14:35:13 OpenWrt local2.info chat[12330]: CONNECT
Mar 30 14:35:13 OpenWrt local2.info chat[12330]:  -- got it
Mar 30 14:35:13 OpenWrt local2.info chat[12330]: send ( ^M)
Mar 30 14:35:13 OpenWrt daemon.info pppd[11501]: Serial connection established.
Mar 30 14:35:13 OpenWrt daemon.info pppd[11501]: Using interface 3g-3g
Mar 30 14:35:13 OpenWrt daemon.notice pppd[11501]: Connect: 3g-3g <--> /dev/ttyUSB0
Mar 30 14:35:14 OpenWrt daemon.info pppd[11501]: CHAP authentication succeeded
Mar 30 14:35:14 OpenWrt daemon.notice pppd[11501]: CHAP authentication succeeded
Mar 30 14:35:15 OpenWrt daemon.info pppd[11501]: Hangup (SIGHUP)
Mar 30 14:35:15 OpenWrt daemon.notice pppd[11501]: Modem hangup
Mar 30 14:35:15 OpenWrt daemon.notice pppd[11501]: Connection terminated.
Mar 30 14:35:28 OpenWrt user.info kernel: usb 1-1: USB disconnect, address 3
Mar 30 14:35:28 OpenWrt user.err kernel: option: option_instat_callback: error -143
Mar 30 14:35:28 OpenWrt user.info kernel: option1 ttyUSB0: GSM modem (1-port) converter now disconnected from ttyUSB0
Mar 30 14:35:28 OpenWrt user.info kernel: option 1-1:1.0: device disconnected
Mar 30 14:35:28 OpenWrt user.info kernel: option1 ttyUSB1: GSM modem (1-port) converter now disconnected from ttyUSB1
Mar 30 14:35:28 OpenWrt user.info kernel: option 1-1:1.3: device disconnected
Mar 30 14:35:28 OpenWrt user.info kernel: option1 ttyUSB2: GSM modem (1-port) converter now disconnected from ttyUSB2
Mar 30 14:35:28 OpenWrt user.info kernel: option 1-1:1.4: device disconnected
Mar 30 14:35:28 OpenWrt user.notice 3g-hotplug: Stopping interface 3g for device ttyUSB0
Mar 30 14:35:28 OpenWrt daemon.info pppd[11501]: Terminating on signal 15
Mar 30 14:35:28 OpenWrt daemon.info pppd[11501]: Exit.
Mar 30 14:35:30 OpenWrt daemon.info hostapd: wlan0: STA 78:d6:f0:8f:d3:a9 IEEE 802.11: authenticated
Mar 30 14:35:30 OpenWrt daemon.info hostapd: wlan0: STA 78:d6:f0:8f:d3:a9 IEEE 802.11: associated (aid 1)
Mar 30 14:35:33 OpenWrt daemon.info hostapd: wlan0: STA 78:d6:f0:8f:d3:a9 IEEE 802.11: authenticated
Mar 30 14:35:33 OpenWrt daemon.info hostapd: wlan0: STA 78:d6:f0:8f:d3:a9 IEEE 802.11: associated (aid 1)
Mar 30 14:35:34 OpenWrt daemon.info hostapd: wlan0: STA 78:d6:f0:8f:d3:a9 WPA: pairwise key handshake completed (RSN)
Mar 30 14:35:34 OpenWrt daemon.info dnsmasq-dhcp[11063]: DHCPREQUEST(br-lan) 192.168.1.112 78:d6:f0:8f:d3:a9
Mar 30 14:35:34 OpenWrt daemon.info dnsmasq-dhcp[11063]: DHCPACK(br-lan) 192.168.1.112 78:d6:f0:8f:d3:a9 android-d0a4fe783e3cd689
Mar 30 14:35:34 OpenWrt user.info kernel: usb 1-1: new high speed USB device using ar71xx-ehci and address 4
Mar 30 14:35:34 OpenWrt user.info kernel: usb 1-1: configuration #1 chosen from 1 choice
Mar 30 14:35:34 OpenWrt user.notice usb-modeswitch: 1-1:1.0: Manufacturer=Huawei_Technologies Product=HUAWEI_Mobile Serial=?
Mar 30 14:35:34 OpenWrt user.notice usb-modeswitch: 1-1:1.0: Selecting /etc/usb_modeswitch.d/12d1:1446 for mode switching
Mar 30 14:35:34 OpenWrt user.warn kernel: usb 1-1: usbfs: process 12624 (usb_modeswitch) did not claim interface 0 before use
Mar 30 14:35:34 OpenWrt user.info kernel: usb 1-1: USB disconnect, address 4
Mar 30 14:35:39 OpenWrt user.info kernel: usb 1-1: new high speed USB device using ar71xx-ehci and address 5
Mar 30 14:35:39 OpenWrt user.info kernel: usb 1-1: configuration #1 chosen from 1 choice
Mar 30 14:35:39 OpenWrt user.info kernel: option 1-1:1.0: GSM modem (1-port) converter detected
Mar 30 14:35:39 OpenWrt user.info kernel: usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0
Mar 30 14:35:39 OpenWrt user.info kernel: option 1-1:1.3: GSM modem (1-port) converter detected
Mar 30 14:35:39 OpenWrt user.info kernel: usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1
Mar 30 14:35:39 OpenWrt user.info kernel: option 1-1:1.4: GSM modem (1-port) converter detected
Mar 30 14:35:39 OpenWrt user.info kernel: usb 1-1: GSM modem (1-port) converter now attached to ttyUSB2
Mar 30 14:35:40 OpenWrt user.notice usb-modeswitch: 1-1:1.1: Manufacturer=Huawei_Technologies Product=HUAWEI_Mobile Serial=?
Mar 30 14:35:41 OpenWrt user.notice usb-modeswitch: 1-1:1.0: Manufacturer=Huawei_Technologies Product=HUAWEI_Mobile Serial=?
Mar 30 14:35:41 OpenWrt user.notice 3g-hotplug: Starting interface 3g for device ttyUSB0
Mar 30 14:35:41 OpenWrt user.notice usb-modeswitch: 1-1:1.1: Manufacturer=Huawei_Technologies Product=HUAWEI_Mobile Serial=?
Mar 30 14:35:41 OpenWrt user.notice usb-modeswitch: 1-1:1.2: Manufacturer=Huawei_Technologies Product=HUAWEI_Mobile Serial=?
Mar 30 14:35:41 OpenWrt user.notice usb-modeswitch: 1-1:1.3: Manufacturer=Huawei_Technologies Product=HUAWEI_Mobile Serial=?
Mar 30 14:35:42 OpenWrt user.notice usb-modeswitch: 1-1:1.4: Manufacturer=Huawei_Technologies Product=HUAWEI_Mobile Serial=?
Mar 30 14:35:42 OpenWrt user.notice usb-modeswitch: 1-1:1.5: Manufacturer=Huawei_Technologies Product=HUAWEI_Mobile Serial=?
Mar 30 14:35:42 OpenWrt user.notice usb-modeswitch: 1-1:1.6: Manufacturer=Huawei_Technologies Product=HUAWEI_Mobile Serial=?
Mar 30 14:35:44 OpenWrt daemon.notice pppd[12862]: pppd 2.4.4 started by root, uid 0
Mar 30 14:35:45 OpenWrt local2.info chat[12867]: abort on (BUSY)
Mar 30 14:35:45 OpenWrt local2.info chat[12867]: abort on (NO CARRIER)
Mar 30 14:35:45 OpenWrt local2.info chat[12867]: abort on (ERROR)
Mar 30 14:35:45 OpenWrt local2.info chat[12867]: report (CONNECT)
Mar 30 14:35:45 OpenWrt local2.info chat[12867]: timeout set to 10 seconds
Mar 30 14:35:45 OpenWrt local2.info chat[12867]: send (AT&F^M)
Mar 30 14:35:45 OpenWrt local2.info chat[12867]: expect (OK)
Mar 30 14:35:45 OpenWrt local2.info chat[12867]: AT&F^M^M
Mar 30 14:35:45 OpenWrt local2.info chat[12867]: OK
Mar 30 14:35:45 OpenWrt local2.info chat[12867]:  -- got it
Mar 30 14:35:45 OpenWrt local2.info chat[12867]: send (ATE1^M)
Mar 30 14:35:45 OpenWrt local2.info chat[12867]: expect (OK)
Mar 30 14:35:45 OpenWrt local2.info chat[12867]: ^M
Mar 30 14:35:45 OpenWrt local2.info chat[12867]: ATE1^M^M
Mar 30 14:35:45 OpenWrt local2.info chat[12867]: OK
Mar 30 14:35:45 OpenWrt local2.info chat[12867]:  -- got it
Mar 30 14:35:45 OpenWrt local2.info chat[12867]: send (AT+CGDCONT=1,"IP","internet"^M)
Mar 30 14:35:46 OpenWrt local2.info chat[12867]: timeout set to 30 seconds
Mar 30 14:35:46 OpenWrt local2.info chat[12867]: expect (OK)
Mar 30 14:35:46 OpenWrt local2.info chat[12867]: ^M
Mar 30 14:35:46 OpenWrt local2.info chat[12867]: AT+CGDCONT=1,"IP","internet"^M^M
Mar 30 14:35:46 OpenWrt local2.info chat[12867]: OK
Mar 30 14:35:46 OpenWrt local2.info chat[12867]:  -- got it
Mar 30 14:35:46 OpenWrt local2.info chat[12867]: send (ATD*99***1#^M)
Mar 30 14:35:46 OpenWrt local2.info chat[12867]: expect (CONNECT)
Mar 30 14:35:46 OpenWrt local2.info chat[12867]: ^M
Mar 30 14:35:46 OpenWrt local2.info chat[12867]: ATD*99***1#^M^M
Mar 30 14:35:46 OpenWrt local2.info chat[12867]: CONNECT
Mar 30 14:35:46 OpenWrt local2.info chat[12867]:  -- got it
Mar 30 14:35:46 OpenWrt local2.info chat[12867]: send ( ^M)
Mar 30 14:35:46 OpenWrt daemon.info pppd[12862]: Serial connection established.
Mar 30 14:35:46 OpenWrt daemon.info pppd[12862]: Using interface 3g-3g
Mar 30 14:35:46 OpenWrt daemon.notice pppd[12862]: Connect: 3g-3g <--> /dev/ttyUSB0
Mar 30 14:35:47 OpenWrt daemon.info pppd[12862]: CHAP authentication succeeded
Mar 30 14:35:47 OpenWrt daemon.notice pppd[12862]: CHAP authentication succeeded
Mar 30 14:35:49 OpenWrt daemon.info pppd[12862]: Hangup (SIGHUP)
Mar 30 14:35:49 OpenWrt daemon.notice pppd[12862]: Modem hangup
Mar 30 14:35:49 OpenWrt daemon.notice pppd[12862]: Connection terminated.
Mar 30 14:36:22 OpenWrt local2.info chat[13068]: abort on (BUSY)
Mar 30 14:36:22 OpenWrt local2.info chat[13068]: abort on (NO CARRIER)
Mar 30 14:36:22 OpenWrt local2.info chat[13068]: abort on (ERROR)
Mar 30 14:36:22 OpenWrt local2.info chat[13068]: report (CONNECT)
Mar 30 14:36:22 OpenWrt local2.info chat[13068]: timeout set to 10 seconds
Mar 30 14:36:22 OpenWrt local2.info chat[13068]: send (AT&F^M)
Mar 30 14:36:22 OpenWrt local2.info chat[13068]: expect (OK)
Mar 30 14:36:22 OpenWrt local2.info chat[13068]: AT&F^M^M
Mar 30 14:36:22 OpenWrt local2.info chat[13068]: OK
Mar 30 14:36:22 OpenWrt local2.info chat[13068]:  -- got it
Mar 30 14:36:22 OpenWrt local2.info chat[13068]: send (ATE1^M)
Mar 30 14:36:22 OpenWrt local2.info chat[13068]: expect (OK)
Mar 30 14:36:22 OpenWrt local2.info chat[13068]: ^M
Mar 30 14:36:22 OpenWrt local2.info chat[13068]: ATE1^M^M
Mar 30 14:36:22 OpenWrt local2.info chat[13068]: OK
Mar 30 14:36:22 OpenWrt local2.info chat[13068]:  -- got it
Mar 30 14:36:22 OpenWrt local2.info chat[13068]: send (AT+CGDCONT=1,"IP","internet"^M)
Mar 30 14:36:22 OpenWrt local2.info chat[13068]: timeout set to 30 seconds
Mar 30 14:36:22 OpenWrt local2.info chat[13068]: expect (OK)
Mar 30 14:36:22 OpenWrt local2.info chat[13068]: ^M
Mar 30 14:36:22 OpenWrt local2.info chat[13068]: AT+CGDCONT=1,"IP","internet"^M^M
Mar 30 14:36:22 OpenWrt local2.info chat[13068]: OK
Mar 30 14:36:22 OpenWrt local2.info chat[13068]:  -- got it
Mar 30 14:36:22 OpenWrt local2.info chat[13068]: send (ATD*99***1#^M)
Mar 30 14:36:22 OpenWrt local2.info chat[13068]: expect (CONNECT)
Mar 30 14:36:22 OpenWrt local2.info chat[13068]: ^M
Mar 30 14:36:22 OpenWrt local2.info chat[13068]: ATD*99***1#^M^M
Mar 30 14:36:22 OpenWrt local2.info chat[13068]: CONNECT
Mar 30 14:36:22 OpenWrt local2.info chat[13068]:  -- got it
Mar 30 14:36:22 OpenWrt local2.info chat[13068]: send ( ^M)
Mar 30 14:36:22 OpenWrt daemon.info pppd[12862]: Serial connection established.
Mar 30 14:36:22 OpenWrt daemon.info pppd[12862]: Using interface 3g-3g
Mar 30 14:36:22 OpenWrt daemon.notice pppd[12862]: Connect: 3g-3g <--> /dev/ttyUSB0
Mar 30 14:36:23 OpenWrt daemon.info pppd[12862]: CHAP authentication succeeded
Mar 30 14:36:23 OpenWrt daemon.notice pppd[12862]: CHAP authentication succeeded
Mar 30 14:36:25 OpenWrt daemon.info pppd[12862]: Hangup (SIGHUP)
Mar 30 14:36:25 OpenWrt daemon.notice pppd[12862]: Modem hangup
Mar 30 14:36:25 OpenWrt daemon.notice pppd[12862]: Connection terminated.

2 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,344

Odp: TL-WR1043ND backfire openwrt i problem z polaczeniem 3G modem E1820

On Ci się rozłącza  zaraz. Strzelam że hub zasilany potrzebujesz do tego modemu.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

3 Odpowiedź przez pepe_lodz

  • Zarejestrowany: 2010-06-18
  • Posty: 974

Odp: TL-WR1043ND backfire openwrt i problem z polaczeniem 3G modem E1820

Tak uwazasz. Kiedys na tym routerze uzywalem modemu E1750 bez huba...dzialal na usb z routera...

4 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,344

Odp: TL-WR1043ND backfire openwrt i problem z polaczeniem 3G modem E1820

A tu masz E1820.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

5 Odpowiedź przez jarek7714

  • Zarejestrowany: 2012-01-13
  • Posty: 1,534

Odp: TL-WR1043ND backfire openwrt i problem z polaczeniem 3G modem E1820

pepe_lodz napisał/a:

Kiedys na tym routerze uzywalem modemu E1750 bez huba...dzialal na usb z routera...

Mam ten modem i łączy się bezproblemowo przez aktywny HUB-to jest zależne też od zasięgu sieci (jak modem będzie miał z tym problem i nie dostanie dobrego zasilania po USB to albo się nie połączy lub będzie zrywał połączenie co jakiś czas).

6 Odpowiedź przez pepe_lodz

  • Zarejestrowany: 2010-06-18
  • Posty: 974

Odp: TL-WR1043ND backfire openwrt i problem z polaczeniem 3G modem E1820

No zasieg mam slaby... Jednak dzis w pracy sie tym bawilem i tam zasieg mialem mnie wiecej w polowie...Moze to miec wplyw ?

7 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,344

Odp: TL-WR1043ND backfire openwrt i problem z polaczeniem 3G modem E1820

W tym sensie że modem bierze więcej energii niż normalnie.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

8 Odpowiedź przez pepe_lodz

  • Zarejestrowany: 2010-06-18
  • Posty: 974

Odp: TL-WR1043ND backfire openwrt i problem z polaczeniem 3G modem E1820

Kurcze w pracy mam huba aktywnego. W domu mam monitor z hubem czy taki hub w monitorze lcd jest aktywny wiecie moze ? Bo wtedy bym na probe sprobowal przez monitor puscic modem...

9 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,344

Odp: TL-WR1043ND backfire openwrt i problem z polaczeniem 3G modem E1820

Po prostu podłącz i zobacz.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

10 Odpowiedź przez pepe_lodz (edytowany przez pepe_lodz 2012-03-30 21:07:42)

  • Zarejestrowany: 2010-06-18
  • Posty: 974

Odp: TL-WR1043ND backfire openwrt i problem z polaczeniem 3G modem E1820

No to podlaczylem przez huba w monitorze LCD i nadal nic. Jest tak samo.... Nie chce sie polaczyc...


A ktore wierze mowia o tym ze on sie polaczyl a nastepnie sie rozlaczyl ?

Aha dodam bo to pewnie wazne... Wczesniej wgrywałem Gargoyle i na tym sofcie wtedy laczył mi sie router z netem przy pomocy modemu E1820... A teraz mam Backfire z LUCI gdyz chce zrobic sobie na tym sofcie lacze 3G jako zapasowe i wydaje mi sie Backfire z LUCI ciekawsze smile

11 Odpowiedź przez a.bakus

  • Zarejestrowany: 2011-03-24
  • Posty: 97

Odp: TL-WR1043ND backfire openwrt i problem z polaczeniem 3G modem E1820

Jak nie masz huba z zasilaniem to spróbuj jak się łączy z miejsca gdzie jest dobry zasięg. Modem (komórki) nadają z mocą zależną od odległości od stacji BTS, jeżeli masz słaby sygnał to modem może nie dostaje tyle prądu (chodzi o wielkość fizyczną) ile mu potrzeba z samego portu usb routera i się rozłącza. Nie wykluczam błędnej konfiguracji. Czy na pewno dane odczytujesz z odpowiedniego interfejsu. Spróbuj zmienić i zobaczysz. U mnie też się rozłączał i nie wiedziałem co i jak, ale działałem na złym porcie. Po zmianie wszystko śmiga.

12 Odpowiedź przez pepe_lodz (edytowany przez pepe_lodz 2012-03-31 00:19:33)

  • Zarejestrowany: 2010-06-18
  • Posty: 974

Odp: TL-WR1043ND backfire openwrt i problem z polaczeniem 3G modem E1820

Przed chwila wgrałem Gargoyle i wybralem ttyUSB0 i odrazu modem sie polaczył na usb wpietym do routera bezposrednio. Nie bylo zadnego problemu... i w tym samym miejscu o tym samym zasiegu... Nie wiem juz gdzie szukac przyczyny. Wychodzi na to ze pradu dostaje dostatecznie duzo aby dzialal. Wydaje mi sie ze gdzies mam blad w konfiguracji. Czy moze mnie ktos pokierowac krok po kroku jak skonfigurowac aby dzialal na Backfire z eko.one.pl ? Bede ogromnie wdzieczny...


Wgralem teraz najnowsze Backfire z Eko.one.pl ktore dzis sie ukazalo... Podlaczylem modem. Stworzylem interface pod nazwa 3G. Ustawilem APN, usera i haslo. I modem sie polaczył... Wiec mowie skonfiguruje Firewalla bo internet nie byl przekazywany. Stworzylem ZONE o nazwie 3G i kliknalem SAVE & APPLY i modem rozlaczyl bo router zapisywal... i juz lipa nie polaczyl sie ponownie. Dalem z konsoli IFUP 3G i nic znow to samo jak mowicie ze laczy i zrywa polaczenie. Nie wiem juz co jest naprawde grane. Prosze o pilna pomoc.

Teraz mam komunikaty takie jak robie ifup 3g

root@TL-WR1043ND:/$ ifup 3g
root@TL-WR1043ND:/$ logread
Mar 31 00:32:22 OpenWrt user.info firewall: adding lan (br-lan) to zone lan
Mar 31 00:32:23 OpenWrt user.info firewall: adding wan (eth0.2) to zone wan
Mar 31 00:32:23 OpenWrt local2.info chat[23108]: alarm
Mar 31 00:32:23 OpenWrt local2.info chat[23108]: Failed
Mar 31 00:32:23 OpenWrt daemon.err pppd[23010]: Connect script failed
Mar 31 00:32:55 OpenWrt local2.info chat[23882]: abort on (BUSY)
Mar 31 00:32:55 OpenWrt local2.info chat[23882]: abort on (NO CARRIER)
Mar 31 00:32:55 OpenWrt local2.info chat[23882]: abort on (ERROR)
Mar 31 00:32:55 OpenWrt local2.info chat[23882]: report (CONNECT)
Mar 31 00:32:55 OpenWrt local2.info chat[23882]: timeout set to 10 seconds
Mar 31 00:32:55 OpenWrt local2.info chat[23882]: send (AT&F^M)
Mar 31 00:32:55 OpenWrt local2.info chat[23882]: expect (OK)
Mar 31 00:33:05 OpenWrt local2.info chat[23882]: alarm
Mar 31 00:33:05 OpenWrt local2.info chat[23882]: Failed
Mar 31 00:33:05 OpenWrt daemon.err pppd[23010]: Connect script failed
Mar 31 00:33:37 OpenWrt local2.info chat[24020]: abort on (BUSY)
Mar 31 00:33:37 OpenWrt local2.info chat[24020]: abort on (NO CARRIER)
Mar 31 00:33:37 OpenWrt local2.info chat[24020]: abort on (ERROR)
Mar 31 00:33:37 OpenWrt local2.info chat[24020]: report (CONNECT)
Mar 31 00:33:37 OpenWrt local2.info chat[24020]: timeout set to 10 seconds
Mar 31 00:33:37 OpenWrt local2.info chat[24020]: send (AT&F^M)
Mar 31 00:33:37 OpenWrt local2.info chat[24020]: expect (OK)
Mar 31 00:33:47 OpenWrt local2.info chat[24020]: alarm
Mar 31 00:33:47 OpenWrt local2.info chat[24020]: Failed
Mar 31 00:33:47 OpenWrt daemon.err pppd[23010]: Connect script failed
Mar 31 00:34:01 OpenWrt daemon.info pppd[23010]: Terminating on signal 15
Mar 31 00:34:01 OpenWrt daemon.info pppd[23010]: Exit.
Mar 31 00:34:01 OpenWrt daemon.notice pppd[24155]: pppd 2.4.5 started by root, uid 0
Mar 31 00:34:02 OpenWrt local2.info chat[24160]: abort on (BUSY)
Mar 31 00:34:02 OpenWrt local2.info chat[24160]: abort on (NO CARRIER)
Mar 31 00:34:02 OpenWrt local2.info chat[24160]: abort on (ERROR)
Mar 31 00:34:02 OpenWrt local2.info chat[24160]: report (CONNECT)
Mar 31 00:34:02 OpenWrt local2.info chat[24160]: timeout set to 10 seconds
Mar 31 00:34:02 OpenWrt local2.info chat[24160]: send (AT&F^M)
Mar 31 00:34:02 OpenWrt local2.info chat[24160]: expect (OK)
Mar 31 00:34:12 OpenWrt local2.info chat[24160]: alarm
Mar 31 00:34:12 OpenWrt local2.info chat[24160]: Failed
Mar 31 00:34:12 OpenWrt daemon.err pppd[24155]: Connect script failed
Mar 31 00:34:29 OpenWrt daemon.warn dnsmasq[23395]: failed to access /tmp/resolv.conf.auto: No such file or directory
Mar 31 00:34:30 OpenWrt user.info firewall: removing lan (br-lan) from zone lan
Mar 31 00:34:31 OpenWrt user.info kernel: br-lan: port 1(eth0.1) entering disabled state
Mar 31 00:34:31 OpenWrt user.info kernel: device eth0.1 left promiscuous mode
Mar 31 00:34:31 OpenWrt user.info kernel: br-lan: port 1(eth0.1) entering disabled state
Mar 31 00:34:32 OpenWrt user.info firewall: removing wan (eth0.2) from zone wan
Mar 31 00:34:33 OpenWrt user.info kernel: device eth0 left promiscuous mode
Mar 31 00:34:34 OpenWrt daemon.info pppd[24155]: Terminating on signal 15
Mar 31 00:34:34 OpenWrt daemon.info pppd[24155]: Exit.
Mar 31 00:34:35 OpenWrt user.notice ifup: Enabling Router Solicitations on loopback (lo)
Mar 31 00:34:35 OpenWrt user.info kernel: device eth0.1 entered promiscuous mode
Mar 31 00:34:35 OpenWrt user.info kernel: device eth0 entered promiscuous mode
Mar 31 00:34:35 OpenWrt user.info kernel: br-lan: port 1(eth0.1) entering forwarding state
Mar 31 00:34:37 OpenWrt daemon.notice pppd[24907]: pppd 2.4.5 started by root, uid 0
Mar 31 00:34:38 OpenWrt user.notice ifup: Enabling Router Solicitations on lan (br-lan)
Mar 31 00:34:38 OpenWrt local2.info chat[25011]: abort on (BUSY)
Mar 31 00:34:38 OpenWrt local2.info chat[25011]: abort on (NO CARRIER)
Mar 31 00:34:38 OpenWrt local2.info chat[25011]: abort on (ERROR)
Mar 31 00:34:38 OpenWrt local2.info chat[25011]: report (CONNECT)
Mar 31 00:34:38 OpenWrt local2.info chat[25011]: timeout set to 10 seconds
Mar 31 00:34:38 OpenWrt local2.info chat[25011]: send (AT&F^M)
Mar 31 00:34:38 OpenWrt local2.info chat[25011]: expect (OK)
Mar 31 00:34:38 OpenWrt local2.info chat[25011]: ^M
Mar 31 00:34:38 OpenWrt local2.info chat[25011]: OK
Mar 31 00:34:38 OpenWrt local2.info chat[25011]:  -- got it
Mar 31 00:34:38 OpenWrt local2.info chat[25011]: send (ATE1^M)
Mar 31 00:34:38 OpenWrt local2.info chat[25011]: expect (OK)
Mar 31 00:34:38 OpenWrt local2.info chat[25011]: ^M
Mar 31 00:34:38 OpenWrt local2.info chat[25011]: ^M
Mar 31 00:34:38 OpenWrt local2.info chat[25011]: OK
Mar 31 00:34:38 OpenWrt local2.info chat[25011]:  -- got it
Mar 31 00:34:38 OpenWrt local2.info chat[25011]: send (AT+CGDCONT=1,"IP","www.plusgsm.pl"^M)
Mar 31 00:34:38 OpenWrt daemon.info dnsmasq[23395]: exiting on receipt of SIGTERM
Mar 31 00:34:38 OpenWrt local2.info chat[25011]: timeout set to 30 seconds
Mar 31 00:34:38 OpenWrt local2.info chat[25011]: expect (OK)
Mar 31 00:34:38 OpenWrt local2.info chat[25011]: ^M
Mar 31 00:34:38 OpenWrt local2.info chat[25011]: AT&F^M^M
Mar 31 00:34:38 OpenWrt local2.info chat[25011]: OK
Mar 31 00:34:38 OpenWrt local2.info chat[25011]:  -- got it
Mar 31 00:34:38 OpenWrt local2.info chat[25011]: send (ATD*99***1#^M)
Mar 31 00:34:38 OpenWrt user.notice dnsmasq: DNS rebinding protection is active, will discard upstream RFC1918 responses!
Mar 31 00:34:38 OpenWrt local2.info chat[25011]: expect (CONNECT)
Mar 31 00:34:38 OpenWrt local2.info chat[25011]: ^M
Mar 31 00:34:38 OpenWrt local2.info chat[25011]: ATE1^M^M
Mar 31 00:34:38 OpenWrt local2.info chat[25011]: OK^M
Mar 31 00:34:38 OpenWrt local2.info chat[25011]: AT+CGDCONT=1,"IP","www.plusgsm.pl"^M^M
Mar 31 00:34:38 OpenWrt local2.info chat[25011]: OK^M
Mar 31 00:34:38 OpenWrt local2.info chat[25011]: ATD*99***1#^M^M
Mar 31 00:34:38 OpenWrt local2.info chat[25011]: NO CARRIER
Mar 31 00:34:38 OpenWrt local2.info chat[25011]:  -- failed
Mar 31 00:34:38 OpenWrt local2.info chat[25011]: Failed (NO CARRIER)
Mar 31 00:34:38 OpenWrt daemon.err pppd[24907]: Connect script failed
Mar 31 00:34:38 OpenWrt user.notice dnsmasq: Allowing 127.0.0.0/8 responses
Mar 31 00:34:39 OpenWrt user.info firewall: adding lan (br-lan) to zone lan
Mar 31 00:34:39 OpenWrt user.notice ifup: Allowing Router Advertisements on wan (eth0.2)
Mar 31 00:34:40 OpenWrt user.info firewall: adding wan (eth0.2) to zone wan
Mar 31 00:34:42 OpenWrt daemon.info dnsmasq[25288]: started, version 2.55 cachesize 150
Mar 31 00:34:42 OpenWrt daemon.info dnsmasq[25288]: compile time options: IPv6 GNU-getopt no-DBus no-I18N DHCP TFTP
Mar 31 00:34:42 OpenWrt daemon.info dnsmasq-dhcp[25288]: DHCP, IP range 192.168.1.100 -- 192.168.1.250, lease time 12h
Mar 31 00:34:42 OpenWrt daemon.info dnsmasq[25288]: using local addresses only for domain lan
Mar 31 00:34:42 OpenWrt daemon.info dnsmasq[25288]: reading /tmp/resolv.conf.auto
Mar 31 00:34:42 OpenWrt daemon.info dnsmasq[25288]: using nameserver xx.xxx.xxx.xx#53
Mar 31 00:34:42 OpenWrt daemon.info dnsmasq[25288]: using nameserver xx.xxx.xxx.xx#53
Mar 31 00:34:42 OpenWrt daemon.info dnsmasq[25288]: using local addresses only for domain lan
Mar 31 00:34:42 OpenWrt daemon.info dnsmasq[25288]: read /etc/hosts - 1 addresses
Mar 31 00:34:42 OpenWrt daemon.info dnsmasq-dhcp[25288]: read /etc/ethers - 0 addresses
Mar 31 00:34:46 OpenWrt user.info firewall: adding lan (br-lan) to zone lan
Mar 31 00:34:46 OpenWrt user.info firewall: adding wan (eth0.2) to zone wan
Mar 31 00:34:55 OpenWrt daemon.info pppd[24907]: Terminating on signal 15
Mar 31 00:34:55 OpenWrt daemon.info pppd[24907]: Exit.
Mar 31 00:34:56 OpenWrt daemon.notice pppd[25705]: pppd 2.4.5 started by root, uid 0
Mar 31 00:34:57 OpenWrt local2.info chat[25710]: abort on (BUSY)
Mar 31 00:34:57 OpenWrt local2.info chat[25710]: abort on (NO CARRIER)
Mar 31 00:34:57 OpenWrt local2.info chat[25710]: abort on (ERROR)
Mar 31 00:34:57 OpenWrt local2.info chat[25710]: report (CONNECT)
Mar 31 00:34:57 OpenWrt local2.info chat[25710]: timeout set to 10 seconds
Mar 31 00:34:57 OpenWrt local2.info chat[25710]: send (AT&F^M)
Mar 31 00:34:57 OpenWrt local2.info chat[25710]: expect (OK)
Mar 31 00:34:57 OpenWrt local2.info chat[25710]: AT&F^M^M
Mar 31 00:34:57 OpenWrt local2.info chat[25710]: OK
Mar 31 00:34:57 OpenWrt local2.info chat[25710]:  -- got it
Mar 31 00:34:57 OpenWrt local2.info chat[25710]: send (ATE1^M)
Mar 31 00:34:57 OpenWrt local2.info chat[25710]: expect (OK)
Mar 31 00:34:57 OpenWrt local2.info chat[25710]: ^M
Mar 31 00:34:57 OpenWrt local2.info chat[25710]: ATE1^M^M
Mar 31 00:34:57 OpenWrt local2.info chat[25710]: OK
Mar 31 00:34:57 OpenWrt local2.info chat[25710]:  -- got it
Mar 31 00:34:57 OpenWrt local2.info chat[25710]: send (AT+CGDCONT=1,"IP","www.plusgsm.pl"^M)
Mar 31 00:34:57 OpenWrt local2.info chat[25710]: timeout set to 30 seconds
Mar 31 00:34:57 OpenWrt local2.info chat[25710]: expect (OK)
Mar 31 00:34:57 OpenWrt local2.info chat[25710]: ^M
Mar 31 00:34:57 OpenWrt local2.info chat[25710]: AT+CGDCONT=1,"IP","www.plusgsm.pl"^M^M
Mar 31 00:34:57 OpenWrt local2.info chat[25710]: OK
Mar 31 00:34:57 OpenWrt local2.info chat[25710]:  -- got it
Mar 31 00:34:57 OpenWrt local2.info chat[25710]: send (ATD*99***1#^M)
Mar 31 00:34:57 OpenWrt local2.info chat[25710]: expect (CONNECT)
Mar 31 00:34:57 OpenWrt local2.info chat[25710]: ^M
Mar 31 00:34:57 OpenWrt local2.info chat[25710]: ATD*99***1#^M^M
Mar 31 00:34:57 OpenWrt local2.info chat[25710]: NO CARRIER
Mar 31 00:34:57 OpenWrt local2.info chat[25710]:  -- failed
Mar 31 00:34:57 OpenWrt local2.info chat[25710]: Failed (NO CARRIER)
Mar 31 00:34:57 OpenWrt daemon.err pppd[25705]: Connect script failed
Mar 31 00:35:29 OpenWrt local2.info chat[25832]: abort on (BUSY)
Mar 31 00:35:29 OpenWrt local2.info chat[25832]: abort on (NO CARRIER)
Mar 31 00:35:29 OpenWrt local2.info chat[25832]: abort on (ERROR)
Mar 31 00:35:29 OpenWrt local2.info chat[25832]: report (CONNECT)
Mar 31 00:35:29 OpenWrt local2.info chat[25832]: timeout set to 10 seconds
Mar 31 00:35:29 OpenWrt local2.info chat[25832]: send (AT&F^M)
Mar 31 00:35:30 OpenWrt local2.info chat[25832]: expect (OK)
Mar 31 00:35:30 OpenWrt local2.info chat[25832]: AT&F^M^M
Mar 31 00:35:30 OpenWrt local2.info chat[25832]: OK
Mar 31 00:35:30 OpenWrt local2.info chat[25832]:  -- got it
Mar 31 00:35:30 OpenWrt local2.info chat[25832]: send (ATE1^M)
Mar 31 00:35:30 OpenWrt local2.info chat[25832]: expect (OK)
Mar 31 00:35:30 OpenWrt local2.info chat[25832]: ^M
Mar 31 00:35:30 OpenWrt local2.info chat[25832]: ATE1^M^M
Mar 31 00:35:30 OpenWrt local2.info chat[25832]: OK
Mar 31 00:35:30 OpenWrt local2.info chat[25832]:  -- got it
Mar 31 00:35:30 OpenWrt local2.info chat[25832]: send (AT+CGDCONT=1,"IP","www.plusgsm.pl"^M)
Mar 31 00:35:30 OpenWrt local2.info chat[25832]: timeout set to 30 seconds
Mar 31 00:35:30 OpenWrt local2.info chat[25832]: expect (OK)
Mar 31 00:35:30 OpenWrt local2.info chat[25832]: ^M
Mar 31 00:35:30 OpenWrt local2.info chat[25832]: AT+CGDCONT=1,"IP","www.plusgsm.pl"^M^M
Mar 31 00:35:30 OpenWrt local2.info chat[25832]: OK
Mar 31 00:35:30 OpenWrt local2.info chat[25832]:  -- got it
Mar 31 00:35:30 OpenWrt local2.info chat[25832]: send (ATD*99***1#^M)
Mar 31 00:35:30 OpenWrt local2.info chat[25832]: expect (CONNECT)
Mar 31 00:35:30 OpenWrt local2.info chat[25832]: ^M
Mar 31 00:35:30 OpenWrt local2.info chat[25832]: ATD*99***1#^M^M
Mar 31 00:35:30 OpenWrt local2.info chat[25832]: NO CARRIER
Mar 31 00:35:30 OpenWrt local2.info chat[25832]:  -- failed
Mar 31 00:35:30 OpenWrt local2.info chat[25832]: Failed (NO CARRIER)
Mar 31 00:35:30 OpenWrt daemon.err pppd[25705]: Connect script failed
Mar 31 00:35:56 OpenWrt daemon.info pppd[25705]: Terminating on signal 15
Mar 31 00:35:56 OpenWrt daemon.info pppd[25705]: Exit.
Mar 31 00:35:56 OpenWrt daemon.notice pppd[25967]: pppd 2.4.5 started by root, uid 0
Mar 31 00:35:57 OpenWrt local2.info chat[25972]: abort on (BUSY)
Mar 31 00:35:57 OpenWrt local2.info chat[25972]: abort on (NO CARRIER)
Mar 31 00:35:57 OpenWrt local2.info chat[25972]: abort on (ERROR)
Mar 31 00:35:57 OpenWrt local2.info chat[25972]: report (CONNECT)
Mar 31 00:35:57 OpenWrt local2.info chat[25972]: timeout set to 10 seconds
Mar 31 00:35:57 OpenWrt local2.info chat[25972]: send (AT&F^M)
Mar 31 00:35:57 OpenWrt local2.info chat[25972]: expect (OK)
Mar 31 00:35:57 OpenWrt local2.info chat[25972]: AT&F^M^M
Mar 31 00:35:57 OpenWrt local2.info chat[25972]: OK
Mar 31 00:35:57 OpenWrt local2.info chat[25972]:  -- got it
Mar 31 00:35:57 OpenWrt local2.info chat[25972]: send (ATE1^M)
Mar 31 00:35:58 OpenWrt local2.info chat[25972]: expect (OK)
Mar 31 00:35:58 OpenWrt local2.info chat[25972]: ^M
Mar 31 00:35:58 OpenWrt local2.info chat[25972]: ATE1^M^M
Mar 31 00:35:58 OpenWrt local2.info chat[25972]: OK
Mar 31 00:35:58 OpenWrt local2.info chat[25972]:  -- got it
Mar 31 00:35:58 OpenWrt local2.info chat[25972]: send (AT+CGDCONT=1,"IP","www.plusgsm.pl"^M)
Mar 31 00:35:58 OpenWrt local2.info chat[25972]: timeout set to 30 seconds
Mar 31 00:35:58 OpenWrt local2.info chat[25972]: expect (OK)
Mar 31 00:35:58 OpenWrt local2.info chat[25972]: ^M
Mar 31 00:35:58 OpenWrt local2.info chat[25972]: AT+CGDCONT=1,"IP","www.plusgsm.pl"^M^M
Mar 31 00:35:58 OpenWrt local2.info chat[25972]: OK
Mar 31 00:35:58 OpenWrt local2.info chat[25972]:  -- got it
Mar 31 00:35:58 OpenWrt local2.info chat[25972]: send (ATD*99***1#^M)
Mar 31 00:35:58 OpenWrt local2.info chat[25972]: expect (CONNECT)
Mar 31 00:35:58 OpenWrt local2.info chat[25972]: ^M
Mar 31 00:35:58 OpenWrt local2.info chat[25972]: ATD*99***1#^M^M
Mar 31 00:35:58 OpenWrt local2.info chat[25972]: NO CARRIER
Mar 31 00:35:58 OpenWrt local2.info chat[25972]:  -- failed
Mar 31 00:35:58 OpenWrt local2.info chat[25972]: Failed (NO CARRIER)
Mar 31 00:35:58 OpenWrt daemon.err pppd[25967]: Connect script failed
Mar 31 00:35:58 OpenWrt daemon.info pppd[25967]: Terminating on signal 15
Mar 31 00:35:58 OpenWrt daemon.info pppd[25967]: Exit.
Mar 31 00:35:59 OpenWrt daemon.notice pppd[26039]: pppd 2.4.5 started by root, uid 0
Mar 31 00:36:00 OpenWrt local2.info chat[26044]: abort on (BUSY)
Mar 31 00:36:00 OpenWrt local2.info chat[26044]: abort on (NO CARRIER)
Mar 31 00:36:00 OpenWrt local2.info chat[26044]: abort on (ERROR)
Mar 31 00:36:00 OpenWrt local2.info chat[26044]: report (CONNECT)
Mar 31 00:36:00 OpenWrt local2.info chat[26044]: timeout set to 10 seconds
Mar 31 00:36:00 OpenWrt local2.info chat[26044]: send (AT&F^M)
Mar 31 00:36:00 OpenWrt local2.info chat[26044]: expect (OK)
Mar 31 00:36:00 OpenWrt local2.info chat[26044]: AT&F^M^M
Mar 31 00:36:00 OpenWrt local2.info chat[26044]: OK
Mar 31 00:36:00 OpenWrt local2.info chat[26044]:  -- got it
Mar 31 00:36:00 OpenWrt local2.info chat[26044]: send (ATE1^M)
Mar 31 00:36:00 OpenWrt local2.info chat[26044]: expect (OK)
Mar 31 00:36:00 OpenWrt local2.info chat[26044]: ^M
Mar 31 00:36:00 OpenWrt local2.info chat[26044]: ATE1^M^M
Mar 31 00:36:00 OpenWrt local2.info chat[26044]: OK
Mar 31 00:36:00 OpenWrt local2.info chat[26044]:  -- got it
Mar 31 00:36:00 OpenWrt local2.info chat[26044]: send (AT+CGDCONT=1,"IP","www.plusgsm.pl"^M)
Mar 31 00:36:00 OpenWrt local2.info chat[26044]: timeout set to 30 seconds
Mar 31 00:36:00 OpenWrt local2.info chat[26044]: expect (OK)
Mar 31 00:36:00 OpenWrt local2.info chat[26044]: ^M
Mar 31 00:36:00 OpenWrt local2.info chat[26044]: AT+CGDCONT=1,"IP","www.plusgsm.pl"^M^M
Mar 31 00:36:00 OpenWrt local2.info chat[26044]: OK
Mar 31 00:36:00 OpenWrt local2.info chat[26044]:  -- got it
Mar 31 00:36:00 OpenWrt local2.info chat[26044]: send (ATD*99***1#^M)
Mar 31 00:36:00 OpenWrt local2.info chat[26044]: expect (CONNECT)
Mar 31 00:36:00 OpenWrt local2.info chat[26044]: ^M
Mar 31 00:36:00 OpenWrt local2.info chat[26044]: ATD*99***1#^M^M
Mar 31 00:36:00 OpenWrt local2.info chat[26044]: NO CARRIER
Mar 31 00:36:00 OpenWrt local2.info chat[26044]:  -- failed
Mar 31 00:36:00 OpenWrt local2.info chat[26044]: Failed (NO CARRIER)
Mar 31 00:36:00 OpenWrt daemon.err pppd[26039]: Connect script failed


Jeszcze tez co pomyslalem ze moj modem sie nie przelacza w tryb modemu.
Dane mojego modemu:
P:  Vendor=12d1 ProdID=14ac Rev= 0.00
S:  Manufacturer=Huawei Technologies
S:  Product=HUAWEI Mobile

a w katalogu /etc/usb_modeswitch.d nie ma pliku o nazwie 12d1:14ac

ale moze sie myle co do tego...?

13 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,344

Odp: TL-WR1043ND backfire openwrt i problem z polaczeniem 3G modem E1820

Bo 14ac to już pid docelowy, po przełączeniu. z 1446 pochodzi.

Dodaj opcję debug i noipdefault do konfiga ppp.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

14 Odpowiedź przez a.bakus (edytowany przez a.bakus 2012-03-31 08:02:06)

  • Zarejestrowany: 2011-03-24
  • Posty: 97

Odp: TL-WR1043ND backfire openwrt i problem z polaczeniem 3G modem E1820

U mnie "NO CARRIER" było jak się komunikowałem z niewłaściwym portem danych ttyUSB1 zmieniłem na ttyUSB0 i śmiga.  Mam modem Hauwei E170.

Podpowiedzi masz na http://eko.one.pl/forum/viewtopic.php?id=2927

15 Odpowiedź przez pepe_lodz (edytowany przez pepe_lodz 2012-03-31 10:36:35)

  • Zarejestrowany: 2010-06-18
  • Posty: 974

Odp: TL-WR1043ND backfire openwrt i problem z polaczeniem 3G modem E1820

Cezary napisał/a:

Bo 14ac to już pid docelowy, po przełączeniu. z 1446 pochodzi.

Dodaj opcję debug i noipdefault do konfiga ppp.

A mam prośbę możesz mi dokładniej podać gdzie to wpisać i co mam wpisać... Nie znam sie az tak na linuxie...


Dodam tylko że dzis rano po nocy wlaczylem router do zasilania( bo byl odlaczony) i modem GSM był wpiety do usb. Po starcie routera modem polaczył sie sam i trzyma połaczenie. Jednak cos jest nie tak skoro raz dziala a raz nie... dlatego chciałbym znaleźć przyczyne...

No i wszedlem przez LUCI do NETWORK INTERFACE i dałem na polaczeniu GSM CONNECT (czyli jakby odswierzenie) modem rozłączył sie i już nie chce sie polaczyć.... Nie wiem co jest grane z tym .

16 Odpowiedź przez pepe_lodz (edytowany przez pepe_lodz 2012-03-31 10:39:41)

  • Zarejestrowany: 2010-06-18
  • Posty: 974

Odp: TL-WR1043ND backfire openwrt i problem z polaczeniem 3G modem E1820

a.bakus napisał/a:

U mnie "NO CARRIER" było jak się komunikowałem z niewłaściwym portem danych ttyUSB1 zmieniłem na ttyUSB0 i śmiga.  Mam modem Hauwei E170.

Podpowiedzi masz na http://eko.one.pl/forum/viewtopic.php?id=2927

Czy ty tez masz BACKFIRE z LUCI ? Masz łaczde tylko GSM czy tez z kablowym masz powiazzane ?
Czy dałbys rade np na gg lub mailowo pomoc mi krok po kroku skonfigurowac dzialanie tego z moim modemem ? bo juz rece mi opadly. Najlepiej ustawienie po kolei wszystkiego od wgrania czystego backfire... Bede ogromnie wdzieczny. Z linka ktory podales widze ze mam dobrze ustawione ttyUSB0 dla mojego modemu E1820...

17 Odpowiedź przez pepe_lodz (edytowany przez pepe_lodz 2012-03-31 11:33:39)

  • Zarejestrowany: 2010-06-18
  • Posty: 974

Odp: TL-WR1043ND backfire openwrt i problem z polaczeniem 3G modem E1820

dodałem w pliku /etc/ppp/option   wpis debu i noipdefault. Gdy z konsoli dałem na ifup GSM ( bo GSM mam nazwany interface) to modem odrazu sie połączył. Dałem przez LUCI na stop dla interfacu WAN aby zobaczyć czy bedzie ok. Wtedy modem juz nie dawał internetu na koncówke klincka LAN.

Gdy dałem znow z kosoli ifup GSM to nie łączy i mam w logread znow takie cos:

root@TL-WR1043ND:~$ logread
Mar 31 12:03:27 TL-WR1043ND local2.info chat[16189]: ATE1^M^M
Mar 31 12:03:27 TL-WR1043ND local2.info chat[16189]: OK
Mar 31 12:03:27 TL-WR1043ND local2.info chat[16189]:  -- got it
Mar 31 12:03:27 TL-WR1043ND local2.info chat[16189]: send (AT+CGDCONT=1,"IP","www.plusgsm.pl"^M)
Mar 31 12:03:27 TL-WR1043ND local2.info chat[16189]: timeout set to 30 seconds
Mar 31 12:03:27 TL-WR1043ND local2.info chat[16189]: expect (OK)
Mar 31 12:03:27 TL-WR1043ND local2.info chat[16189]: ^M
Mar 31 12:03:27 TL-WR1043ND local2.info chat[16189]: AT+CGDCONT=1,"IP","www.plusgsm.pl"^M^M
Mar 31 12:03:27 TL-WR1043ND local2.info chat[16189]: OK
Mar 31 12:03:27 TL-WR1043ND local2.info chat[16189]:  -- got it
Mar 31 12:03:27 TL-WR1043ND local2.info chat[16189]: send (ATD*99***1#^M)
Mar 31 12:03:27 TL-WR1043ND local2.info chat[16189]: expect (CONNECT)
Mar 31 12:03:27 TL-WR1043ND local2.info chat[16189]: ^M
Mar 31 12:03:27 TL-WR1043ND local2.info chat[16189]: ATD*99***1#^M^M
Mar 31 12:03:27 TL-WR1043ND local2.info chat[16189]: CONNECT
Mar 31 12:03:27 TL-WR1043ND local2.info chat[16189]:  -- got it
Mar 31 12:03:27 TL-WR1043ND local2.info chat[16189]: send ( ^M)
Mar 31 12:03:27 TL-WR1043ND daemon.info pppd[9728]: Serial connection established.
Mar 31 12:03:27 TL-WR1043ND daemon.info pppd[9728]: Using interface 3g-GSM
Mar 31 12:03:27 TL-WR1043ND daemon.notice pppd[9728]: Connect: 3g-GSM <--> /dev/ttyUSB0
Mar 31 12:03:28 TL-WR1043ND daemon.info pppd[9728]: CHAP authentication succeeded
Mar 31 12:03:28 TL-WR1043ND daemon.notice pppd[9728]: CHAP authentication succeeded
Mar 31 12:03:29 TL-WR1043ND daemon.info pppd[9728]: Terminating on signal 15
Mar 31 12:03:29 TL-WR1043ND daemon.notice pppd[9728]: Connection terminated.
Mar 31 12:03:29 TL-WR1043ND daemon.info pppd[9728]: Exit.
Mar 31 12:03:30 TL-WR1043ND daemon.notice pppd[16298]: pppd 2.4.5 started by root, uid 0
Mar 31 12:03:31 TL-WR1043ND local2.info chat[16304]: abort on (BUSY)
Mar 31 12:03:31 TL-WR1043ND local2.info chat[16304]: abort on (NO CARRIER)
Mar 31 12:03:31 TL-WR1043ND local2.info chat[16304]: abort on (ERROR)
Mar 31 12:03:31 TL-WR1043ND local2.info chat[16304]: report (CONNECT)
Mar 31 12:03:31 TL-WR1043ND local2.info chat[16304]: timeout set to 10 seconds
Mar 31 12:03:31 TL-WR1043ND local2.info chat[16304]: send (AT&F^M)
Mar 31 12:03:31 TL-WR1043ND local2.info chat[16304]: expect (OK)
Mar 31 12:03:31 TL-WR1043ND local2.info chat[16304]: AT&F^M^M
Mar 31 12:03:31 TL-WR1043ND local2.info chat[16304]: OK
Mar 31 12:03:31 TL-WR1043ND local2.info chat[16304]:  -- got it
Mar 31 12:03:31 TL-WR1043ND local2.info chat[16304]: send (ATE1^M)
Mar 31 12:03:32 TL-WR1043ND local2.info chat[16304]: expect (OK)
Mar 31 12:03:32 TL-WR1043ND local2.info chat[16304]: ^M
Mar 31 12:03:32 TL-WR1043ND local2.info chat[16304]: ATE1^M^M
Mar 31 12:03:32 TL-WR1043ND local2.info chat[16304]: OK
Mar 31 12:03:32 TL-WR1043ND local2.info chat[16304]:  -- got it
Mar 31 12:03:32 TL-WR1043ND local2.info chat[16304]: send (AT+CGDCONT=1,"IP","www.plusgsm.pl"^M)
Mar 31 12:03:32 TL-WR1043ND local2.info chat[16304]: timeout set to 30 seconds
Mar 31 12:03:32 TL-WR1043ND local2.info chat[16304]: expect (OK)
Mar 31 12:03:32 TL-WR1043ND local2.info chat[16304]: ^M
Mar 31 12:03:32 TL-WR1043ND local2.info chat[16304]: AT+CGDCONT=1,"IP","www.plusgsm.pl"^M^M
Mar 31 12:03:32 TL-WR1043ND local2.info chat[16304]: OK
Mar 31 12:03:32 TL-WR1043ND local2.info chat[16304]:  -- got it
Mar 31 12:03:32 TL-WR1043ND local2.info chat[16304]: send (ATD*99***1#^M)
Mar 31 12:03:32 TL-WR1043ND local2.info chat[16304]: expect (CONNECT)
Mar 31 12:03:32 TL-WR1043ND local2.info chat[16304]: ^M
Mar 31 12:03:32 TL-WR1043ND local2.info chat[16304]: ATD*99***1#^M^M
Mar 31 12:03:32 TL-WR1043ND local2.info chat[16304]: CONNECT
Mar 31 12:03:32 TL-WR1043ND local2.info chat[16304]:  -- got it
Mar 31 12:03:32 TL-WR1043ND local2.info chat[16304]: send ( ^M)
Mar 31 12:03:32 TL-WR1043ND daemon.debug pppd[16298]: Script USE_APN=www.plusgsm.pl /usr/sbin/chat -t5 -v -E -f /etc/chatscripts/3g.chat finished (pid 16303), status = 0x0
Mar 31 12:03:32 TL-WR1043ND daemon.info pppd[16298]: Serial connection established.
Mar 31 12:03:32 TL-WR1043ND daemon.debug pppd[16298]: using channel 111
Mar 31 12:03:32 TL-WR1043ND daemon.info pppd[16298]: Using interface 3g-GSM
Mar 31 12:03:32 TL-WR1043ND daemon.notice pppd[16298]: Connect: 3g-GSM <--> /dev/ttyUSB0
Mar 31 12:03:33 TL-WR1043ND daemon.debug pppd[16298]: sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x6877ca3a>]
Mar 31 12:03:33 TL-WR1043ND daemon.debug pppd[16298]: rcvd [LCP ConfReq id=0x9f <asyncmap 0x0> <auth chap MD5> <magic 0x2f40748> <pcomp> <accomp>]
Mar 31 12:03:33 TL-WR1043ND daemon.debug pppd[16298]: sent [LCP ConfRej id=0x9f <pcomp> <accomp>]
Mar 31 12:03:33 TL-WR1043ND daemon.debug pppd[16298]: rcvd [LCP ConfAck id=0x1 <asyncmap 0x0> <magic 0x6877ca3a>]
Mar 31 12:03:33 TL-WR1043ND daemon.debug pppd[16298]: rcvd [LCP ConfReq id=0xa0 <asyncmap 0x0> <auth chap MD5> <magic 0x2f40748>]
Mar 31 12:03:33 TL-WR1043ND daemon.debug pppd[16298]: sent [LCP ConfAck id=0xa0 <asyncmap 0x0> <auth chap MD5> <magic 0x2f40748>]
Mar 31 12:03:33 TL-WR1043ND daemon.debug pppd[16298]: sent [LCP EchoReq id=0x0 magic=0x6877ca3a]
Mar 31 12:03:33 TL-WR1043ND daemon.debug pppd[16298]: rcvd [LCP DiscReq id=0xa1 magic=0x2f40748]
Mar 31 12:03:33 TL-WR1043ND daemon.debug pppd[16298]: rcvd [CHAP Challenge id=0x1 <f6e268b402e10c52627488cb5236916b>, name = "UMTS_CHAP_SRVR"]
Mar 31 12:03:33 TL-WR1043ND daemon.debug pppd[16298]: sent [CHAP Response id=0x1 <17f2a5899dd1f34e5829b3406d6dd332>, name = "internet"]
Mar 31 12:03:33 TL-WR1043ND daemon.debug pppd[16298]: rcvd [LCP EchoRep id=0x0 magic=0x2f40748 68 77 ca 3a]
Mar 31 12:03:33 TL-WR1043ND daemon.debug pppd[16298]: rcvd [CHAP Success id=0x1 ""]
Mar 31 12:03:33 TL-WR1043ND daemon.info pppd[16298]: CHAP authentication succeeded
Mar 31 12:03:33 TL-WR1043ND daemon.notice pppd[16298]: CHAP authentication succeeded
Mar 31 12:03:33 TL-WR1043ND daemon.debug pppd[16298]: sent [IPCP ConfReq id=0x1 <addr 0.0.0.0> <ms-dns1 0.0.0.0> <ms-dns2 0.0.0.0>]
Mar 31 12:03:34 TL-WR1043ND daemon.debug pppd[16298]: sent [LCP EchoReq id=0x1 magic=0x6877ca3a]
Mar 31 12:03:34 TL-WR1043ND daemon.debug pppd[16298]: rcvd [LCP EchoRep id=0x1 magic=0x2f40748 68 77 ca 3a]
Mar 31 12:03:34 TL-WR1043ND daemon.debug pppd[16298]: rcvd [IPCP ConfNak id=0x1 <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14>]
Mar 31 12:03:34 TL-WR1043ND daemon.debug pppd[16298]: sent [IPCP ConfReq id=0x2 <addr 0.0.0.0> <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14>]
Mar 31 12:03:35 TL-WR1043ND daemon.debug pppd[16298]: sent [LCP EchoReq id=0x2 magic=0x6877ca3a]
Mar 31 12:03:35 TL-WR1043ND daemon.debug pppd[16298]: rcvd [LCP EchoRep id=0x2 magic=0x2f40748 68 77 ca 3a]
Mar 31 12:03:35 TL-WR1043ND daemon.debug pppd[16298]: rcvd [IPCP ConfNak id=0x2 <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14>]
Mar 31 12:03:35 TL-WR1043ND daemon.debug pppd[16298]: sent [IPCP ConfReq id=0x3 <addr 0.0.0.0> <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14>]
Mar 31 12:03:36 TL-WR1043ND daemon.debug pppd[16298]: rcvd [IPCP ConfReq id=0x0]
Mar 31 12:03:36 TL-WR1043ND daemon.debug pppd[16298]: sent [IPCP ConfNak id=0x0 <addr 0.0.0.0>]
Mar 31 12:03:36 TL-WR1043ND daemon.debug pppd[16298]: rcvd [IPCP ConfNak id=0x3 <addr 46.169.124.81> <ms-dns1 212.2.96.51> <ms-dns2 212.2.96.52>]
Mar 31 12:03:36 TL-WR1043ND daemon.debug pppd[16298]: sent [IPCP ConfReq id=0x4 <addr 46.169.124.81> <ms-dns1 212.2.96.51> <ms-dns2 212.2.96.52>]
Mar 31 12:03:36 TL-WR1043ND daemon.debug pppd[16298]: rcvd [IPCP ConfReq id=0x1]
Mar 31 12:03:36 TL-WR1043ND daemon.debug pppd[16298]: sent [IPCP ConfAck id=0x1]
Mar 31 12:03:36 TL-WR1043ND daemon.debug pppd[16298]: rcvd [IPCP ConfAck id=0x4 <addr 46.169.124.81> <ms-dns1 212.2.96.51> <ms-dns2 212.2.96.52>]
Mar 31 12:03:36 TL-WR1043ND daemon.warn pppd[16298]: Could not determine remote IP address: defaulting to 10.64.64.64
Mar 31 12:03:36 TL-WR1043ND daemon.notice pppd[16298]: replacing old default route to eth0.2 [81.219.72.129]
Mar 31 12:03:36 TL-WR1043ND daemon.notice pppd[16298]: local  IP address 46.169.124.81
Mar 31 12:03:36 TL-WR1043ND daemon.notice pppd[16298]: remote IP address 10.64.64.64
Mar 31 12:03:36 TL-WR1043ND daemon.notice pppd[16298]: primary   DNS address 212.2.96.51
Mar 31 12:03:36 TL-WR1043ND daemon.notice pppd[16298]: secondary DNS address 212.2.96.52
Mar 31 12:03:36 TL-WR1043ND daemon.debug pppd[16298]: Script /etc/ppp/ip-up started (pid 16340)
Mar 31 12:03:37 TL-WR1043ND user.notice ifup: Enabling Router Solicitations on GSM (3g-GSM)
Mar 31 12:03:37 TL-WR1043ND daemon.debug pppd[16298]: Script /etc/ppp/ip-up finished (pid 16340), status = 0x1
Mar 31 12:03:37 TL-WR1043ND user.info firewall: adding GSM (3g-GSM) to zone 3g
Mar 31 12:03:39 TL-WR1043ND daemon.info dnsmasq[1544]: reading /tmp/resolv.conf.auto
Mar 31 12:03:39 TL-WR1043ND daemon.info dnsmasq[1544]: using nameserver 212.2.96.52#53
Mar 31 12:03:39 TL-WR1043ND daemon.info dnsmasq[1544]: using nameserver 212.2.96.51#53
Mar 31 12:03:39 TL-WR1043ND daemon.info dnsmasq[1544]: using nameserver 8.8.8.8#53
Mar 31 12:03:39 TL-WR1043ND daemon.info dnsmasq[1544]: using local addresses only for domain lan
Mar 31 12:04:08 TL-WR1043ND daemon.info dnsmasq[1544]: reading /tmp/resolv.conf.auto
Mar 31 12:04:08 TL-WR1043ND daemon.info dnsmasq[1544]: using nameserver 212.2.96.52#53
Mar 31 12:04:08 TL-WR1043ND daemon.info dnsmasq[1544]: using nameserver 212.2.96.51#53
Mar 31 12:04:08 TL-WR1043ND daemon.info dnsmasq[1544]: using local addresses only for domain lan
Mar 31 12:04:09 TL-WR1043ND user.info firewall: removing wan (eth0.2) from zone wan
Mar 31 12:04:27 TL-WR1043ND daemon.info pppd[16298]: No response to 5 echo-requests
Mar 31 12:04:27 TL-WR1043ND daemon.notice pppd[16298]: Serial link appears to be disconnected.
Mar 31 12:04:27 TL-WR1043ND daemon.info pppd[16298]: Connect time 0.9 minutes.
Mar 31 12:04:27 TL-WR1043ND daemon.info pppd[16298]: Sent 5892 bytes, received 18539 bytes.
Mar 31 12:04:27 TL-WR1043ND daemon.notice pppd[16298]: restoring old default route to eth0.2 [81.219.72.129]
Mar 31 12:04:27 TL-WR1043ND daemon.err pppd[16298]: restore default route ioctl(SIOCADDRT): No such process
Mar 31 12:04:27 TL-WR1043ND daemon.debug pppd[16298]: Script /etc/ppp/ip-down started (pid 16796)
Mar 31 12:04:27 TL-WR1043ND daemon.debug pppd[16298]: sent [LCP TermReq id=0x2 "Peer not responding"]
Mar 31 12:04:28 TL-WR1043ND user.info firewall: removing GSM (3g-GSM) from zone 3g
Mar 31 12:04:29 TL-WR1043ND daemon.debug pppd[16298]: Script /etc/ppp/ip-down finished (pid 16796), status = 0x1
Mar 31 12:04:30 TL-WR1043ND daemon.debug pppd[16298]: sent [LCP TermReq id=0x3 "Peer not responding"]
Mar 31 12:04:33 TL-WR1043ND daemon.notice pppd[16298]: Connection terminated.
Mar 31 12:05:00 TL-WR1043ND daemon.err pppd[16298]: ioctl(TIOCSETD, N_TTY): Interrupted system call (line 575)
Mar 31 12:05:01 TL-WR1043ND daemon.info pppd[16298]: Hangup (SIGHUP)
Mar 31 12:05:01 TL-WR1043ND daemon.info pppd[16298]: Terminating on signal 15
Mar 31 12:05:01 TL-WR1043ND daemon.notice pppd[16298]: Modem hangup
Mar 31 12:05:01 TL-WR1043ND daemon.info pppd[16298]: Exit.
Mar 31 12:05:03 TL-WR1043ND daemon.notice pppd[17151]: pppd 2.4.5 started by root, uid 0
Mar 31 12:05:04 TL-WR1043ND local2.info chat[17177]: abort on (BUSY)
Mar 31 12:05:04 TL-WR1043ND local2.info chat[17177]: abort on (NO CARRIER)
Mar 31 12:05:04 TL-WR1043ND local2.info chat[17177]: abort on (ERROR)
Mar 31 12:05:04 TL-WR1043ND local2.info chat[17177]: report (CONNECT)
Mar 31 12:05:04 TL-WR1043ND local2.info chat[17177]: timeout set to 10 seconds
Mar 31 12:05:04 TL-WR1043ND local2.info chat[17177]: send (AT&F^M)
Mar 31 12:05:14 TL-WR1043ND local2.info chat[17177]: alarm
Mar 31 12:05:14 TL-WR1043ND local2.info chat[17177]:  -- write timed out
Mar 31 12:05:14 TL-WR1043ND local2.err chat[17177]: Failed
Mar 31 12:05:14 TL-WR1043ND daemon.debug pppd[17151]: Script USE_APN=www.plusgsm.pl /usr/sbin/chat -t5 -v -E -f /etc/chatscripts/3g.chat finished (pid 17176), status = 0x1
Mar 31 12:05:14 TL-WR1043ND daemon.err pppd[17151]: Connect script failed
Mar 31 12:05:27 TL-WR1043ND daemon.warn pppd[17151]: tcsetattr: Interrupted system call (line 1063)
Mar 31 12:05:33 TL-WR1043ND daemon.notice pppd[17364]: pppd 2.4.5 started by root, uid 0
Mar 31 12:05:33 TL-WR1043ND daemon.notice pppd[17364]: Removed stale lock on ttyUSB0 (pid 17151)
Mar 31 12:05:34 TL-WR1043ND local2.info chat[17369]: abort on (BUSY)
Mar 31 12:05:34 TL-WR1043ND local2.info chat[17369]: abort on (NO CARRIER)
Mar 31 12:05:34 TL-WR1043ND local2.info chat[17369]: abort on (ERROR)
Mar 31 12:05:34 TL-WR1043ND local2.info chat[17369]: report (CONNECT)
Mar 31 12:05:34 TL-WR1043ND local2.info chat[17369]: timeout set to 10 seconds
Mar 31 12:05:34 TL-WR1043ND local2.info chat[17369]: send (AT&F^M)
Mar 31 12:05:44 TL-WR1043ND local2.info chat[17369]: alarm
Mar 31 12:05:44 TL-WR1043ND local2.info chat[17369]:  -- write timed out
Mar 31 12:05:44 TL-WR1043ND local2.err chat[17369]: Failed
Mar 31 12:05:44 TL-WR1043ND daemon.debug pppd[17364]: Script USE_APN=www.plusgsm.pl /usr/sbin/chat -t5 -v -E -f /etc/chatscripts/3g.chat finished (pid 17368), status = 0x1
Mar 31 12:05:44 TL-WR1043ND daemon.err pppd[17364]: Connect script failed
Mar 31 12:05:49 TL-WR1043ND user.notice ifup: Allowing Router Advertisements on wan (eth0.2)
Mar 31 12:05:49 TL-WR1043ND user.info firewall: adding wan (eth0.2) to zone wan
Mar 31 12:05:51 TL-WR1043ND daemon.info dnsmasq[1544]: reading /tmp/resolv.conf.auto
Mar 31 12:05:51 TL-WR1043ND daemon.info dnsmasq[1544]: using nameserver 8.8.8.8#53
Mar 31 12:05:51 TL-WR1043ND daemon.info dnsmasq[1544]: using nameserver 212.2.96.52#53
Mar 31 12:05:51 TL-WR1043ND daemon.info dnsmasq[1544]: using nameserver 212.2.96.51#53
Mar 31 12:05:51 TL-WR1043ND daemon.info dnsmasq[1544]: using local addresses only for domain lan
Mar 31 12:05:54 TL-WR1043ND daemon.warn pppd[17364]: tcsetattr: Interrupted system call (line 1063)
Mar 31 12:06:00 TL-WR1043ND daemon.notice pppd[17816]: pppd 2.4.5 started by root, uid 0
Mar 31 12:06:00 TL-WR1043ND daemon.notice pppd[17816]: Removed stale lock on ttyUSB0 (pid 17364)
Mar 31 12:06:01 TL-WR1043ND local2.info chat[17842]: abort on (BUSY)
Mar 31 12:06:01 TL-WR1043ND local2.info chat[17842]: abort on (NO CARRIER)
Mar 31 12:06:01 TL-WR1043ND local2.info chat[17842]: abort on (ERROR)
Mar 31 12:06:01 TL-WR1043ND local2.info chat[17842]: report (CONNECT)
Mar 31 12:06:01 TL-WR1043ND local2.info chat[17842]: timeout set to 10 seconds
Mar 31 12:06:01 TL-WR1043ND local2.info chat[17842]: send (AT&F^M)
Mar 31 12:06:11 TL-WR1043ND local2.info chat[17842]: alarm
Mar 31 12:06:11 TL-WR1043ND local2.info chat[17842]:  -- write timed out
Mar 31 12:06:11 TL-WR1043ND local2.err chat[17842]: Failed
Mar 31 12:06:11 TL-WR1043ND daemon.debug pppd[17816]: Script USE_APN=www.plusgsm.pl /usr/sbin/chat -t5 -v -E -f /etc/chatscripts/3g.chat finished (pid 17841), status = 0x1
Mar 31 12:06:11 TL-WR1043ND daemon.err pppd[17816]: Connect script failed
Mar 31 12:06:15 TL-WR1043ND daemon.warn pppd[17816]: tcsetattr: Interrupted system call (line 1063)
Mar 31 12:06:20 TL-WR1043ND daemon.notice pppd[17987]: pppd 2.4.5 started by root, uid 0
Mar 31 12:06:20 TL-WR1043ND daemon.notice pppd[17987]: Removed stale lock on ttyUSB0 (pid 17816)
Mar 31 12:06:21 TL-WR1043ND local2.info chat[17993]: abort on (BUSY)
Mar 31 12:06:21 TL-WR1043ND local2.info chat[17993]: abort on (NO CARRIER)
Mar 31 12:06:21 TL-WR1043ND local2.info chat[17993]: abort on (ERROR)
Mar 31 12:06:21 TL-WR1043ND local2.info chat[17993]: report (CONNECT)
Mar 31 12:06:21 TL-WR1043ND local2.info chat[17993]: timeout set to 10 seconds
Mar 31 12:06:21 TL-WR1043ND local2.info chat[17993]: send (AT&F^M)
Mar 31 12:06:31 TL-WR1043ND local2.info chat[17993]: alarm
Mar 31 12:06:31 TL-WR1043ND local2.info chat[17993]:  -- write timed out
Mar 31 12:06:31 TL-WR1043ND local2.err chat[17993]: Failed
Mar 31 12:06:31 TL-WR1043ND daemon.debug pppd[17987]: Script USE_APN=www.plusgsm.pl /usr/sbin/chat -t5 -v -E -f /etc/chatscripts/3g.chat finished (pid 17992), status = 0x1
Mar 31 12:06:31 TL-WR1043ND daemon.err pppd[17987]: Connect script failed


Zrestartowałem router i po restarcie modem sam sie połączył i znow nadawał internet. Jeszcze tylko zauwałyłem ze po restarcie mam laptopa podlaczonego kablem do routera z WIN 7 i po restarcie zle mu przypisal adres IP. Na monitprku kolo godziny był wykrzyknik. Musiałem odpiac kabel LAN i podlaczyc i juz poprawnie przypiane IP. Nie zdarzylo sie tak pierwszy raz...

Doinstalowałem tez do LUCI MULTI-WAN jednak cos nie dziala to poprawnie. Bo niby modem polaczyl sie na kablu WAN mam tez polaczenie. Nastepnie odpiolem kabel WAN od routera a internetu na LANie nie ma. Nie przekierowalo na modem GSM. W LUCI w NETWORK - INTERFACE caly czas widac IP z kabla WAN jakby byl podlaczony. Dopiero jak klikne na STOP dla WAN i nastepnie jeszcze raz CONNECT dla GSM to znow bedzie internet na LANie z odlaczonym WANem... Chcialbym aby to wszystko dzialo sie automatycznie. Tak jak to dziala w TP Link MR3420 ze wszystko dzieje sie automatycznie...

18 Odpowiedź przez a.bakus

  • Zarejestrowany: 2011-03-24
  • Posty: 97

Odp: TL-WR1043ND backfire openwrt i problem z polaczeniem 3G modem E1820

Mam tylko 3g

19 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,344

Odp: TL-WR1043ND backfire openwrt i problem z polaczeniem 3G modem E1820

sent [LCP TermReq id=0x3 "Peer not responding"]

Druga strona nie chce gadać na razie z Tobą.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona