• Zarejestrowany: 2012-03-28
  • Posty: 37

Temat: Hub z alle... za 5 zł nie wykrywa dysku

Witam
Zrobiłem exroota za pomoca poradnika na 1043nd dlaczego po wykonaniu polecenia mount nie mam sdb1?

dysk widzi po poleceniu fdisk

Disk /dev/sdb: 320.0 GB, 320072933376 bytes
255 heads, 63 sectors/track, 38913 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0x97646c29

   Device Boot      Start         End      Blocks   Id  System
/dev/sdb1               1       38913   312568641   83  Linux

mount :

root@Gargoyle:~$ mount
rootfs on / type rootfs (rw)
/dev/root on /rom type squashfs (ro,relatime)
proc on /proc type proc (rw,relatime)
sysfs on /sys type sysfs (rw,relatime)
tmpfs on /tmp type tmpfs (rw,nosuid,nodev,relatime,size=14692k)
tmpfs on /dev type tmpfs (rw,relatime,size=512k,mode=755)
devpts on /dev/pts type devpts (rw,relatime,mode=600)
/dev/sda1 on /overlay type ext3 (rw,noatime,errors=continue,data=writeback)
mini_fo:/overlay on / type mini_fo (rw,relatime)
debugfs on /sys/kernel/debug type debugfs (rw,relatime)
none on /proc/bus/usb type usbfs (rw,relatime)

dmesg

Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Writing ErrCtl register=00000000
Readback ErrCtl register=00000000
Memory: 29228k/32768k available (2175k kernel code, 3540k reserved, 423k data, 152k init, 0k highmem)
SLUB: Genslabs=7, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:56
Calibrating delay loop... 266.24 BogoMIPS (lpj=1331200)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
MIPS: machine is TP-LINK TL-WR1043ND
bio: create slab <bio-0> at 0
Switching to clocksource MIPS
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY)  Š 2001-2006 Red Hat, Inc.
yaffs Mar  2 2012 09:26:17 Installing.
msgmni has been set to 57
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
console [ttyS0] enabled, bootconsole disabled
Atheros AR71xx SPI Controller driver version 0.2.4
m25p80 spi0.0: s25sl064a (8192 Kbytes)
spi0.0: searching for MyLoader partition table at offset 0x10000
spi0.0: searching for MyLoader partition table at offset 0x20000
spi0.0: searching for MyLoader partition table at offset 0x30000
spi0.0: searching for MyLoader partition table at offset 0x40000
spi0.0: no MyLoader partition table found
Searching for RedBoot partition table in spi0.0 at offset 0x7e0000
Searching for RedBoot partition table in spi0.0 at offset 0x7f0000
No RedBoot partition table detected in spi0.0
spi0.0: no WRT160NL signature found
Creating 5 MTD partitions on "spi0.0":
0x000000000000-0x000000020000 : "u-boot"
0x000000020000-0x000000160000 : "kernel"
0x000000160000-0x0000007f0000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=560000, len=290000
0x000000560000-0x0000007f0000 : "rootfs_data"
0x0000007f0000-0x000000800000 : "art"
0x000000020000-0x0000007f0000 : "firmware"
Realtek RTL8366RB ethernet switch driver version 0.2.4
rtl8366rb rtl8366rb: using GPIO pins 18 (SDA) and 19 (SCK)
rtl8366rb rtl8366rb: RTL5937 ver. 2 chip found
rtl8366rb: probed
eth0: Atheros AG71xx at 0xb9000000, irq 4
eth0: using fixed link parameters
Atheros AR71xx hardware watchdog driver version 0.1.0
ar71xx-wdt: timeout=15 secs (max=21)
TCP westwood registered
NET: Registered protocol family 17
Bridge firewalling registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 152k freed
Please be patient, while OpenWrt loads ...
input: gpio-buttons as /devices/platform/gpio-buttons/input/input0
Button Hotplug driver version 0.3.1
ar71xx: pll_reg 0xb8050014: 0x1a000000
eth0: link up (1000Mbps/Full duplex)
Registered led device: tl-wr1043nd:green:usb
Registered led device: tl-wr1043nd:green:system
Registered led device: tl-wr1043nd:green:qss
Registered led device: tl-wr1043nd:green:wlan
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ar71xx-ehci ar71xx-ehci: Atheros AR91xx built-in EHCI controller
ar71xx-ehci ar71xx-ehci: new USB bus registered, assigned bus number 1
ar71xx-ehci ar71xx-ehci: irq 3, io mem 0x1b000000
ar71xx-ehci ar71xx-ehci: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb 1-1: new full speed USB device using ar71xx-ehci and address 2
usb 1-1: configuration #1 chosen from 1 choice
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
usb 1-1.2: new full speed USB device using ar71xx-ehci and address 3
usb 1-1.2: not running at top speed; connect to a high speed hub
usb 1-1.2: configuration #1 chosen from 1 choice
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
usb 1-1.4: new full speed USB device using ar71xx-ehci and address 4
usb 1-1.4: not running at top speed; connect to a high speed hub
usb 1-1.4: configuration #1 chosen from 1 choice
scsi1 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 4
usb-storage: waiting for device to settle before scanning
scsi 0:0:0:0: Direct-Access     Generic  Flash Disk       8.00 PQ: 0 ANSI: 2
usb-storage: device scan complete
sd 0:0:0:0: [sda] 1886208 512-byte logical blocks: (965 MB/921 MiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] Assuming drive cache: write through
 sda: sda1 sda2
scsi 1:0:0:0: Direct-Access     Hitachi  HTS543232L9A300  0200 PQ: 0 ANSI: 4
usb-storage: device scan complete
sd 1:0:0:0: [sdb] 625142448 512-byte logical blocks: (320 GB/298 GiB)
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] Attached SCSI removable disk
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 38 00 00 00
sd 1:0:0:0: [sdb] Assuming drive cache: write through
sd 1:0:0:0: [sdb] Assuming drive cache: write through
 sdb: sdb1
sd 1:0:0:0: [sdb] Assuming drive cache: write through
sd 1:0:0:0: [sdb] Attached SCSI disk
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with writeback data mode.
mini_fo: using base directory: /
mini_fo: using storage directory: /overlay
eth0: link down
ar71xx: pll_reg 0xb8050014: 0x1a000000
eth0: link up (1000Mbps/Full duplex)
device eth0.1 entered promiscuous mode
device eth0 entered promiscuous mode
br-lan: port 1(eth0.1) entering forwarding state
Compat-wireless backport release: compat-wireless-2011-11-29
Backport based on wireless-testing.git master-2011-12-01
cfg80211: Calling CRDA to update world regulatory domain
cfg80211: World regulatory domain updated:
cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:     (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211:     (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211:     (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:     (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
ath: EEPROM regdomain: 0x0
ath: EEPROM indicates default country code should be used
ath: doing EEPROM country->regdmn map search
ath: country maps to regdmn code: 0x3a
ath: Country alpha2 being used: US
ath: Regpair used: 0x3a
ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
ieee80211 phy0: Atheros AR9100 MAC/BB Rev:7 AR2133 RF Rev:a2 mem=0xb80c0000, irq=2
cfg80211: Calling CRDA for country: US
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PPP generic driver version 2.4.2
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
cfg80211: Regulatory domain changed to country: US
cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
cfg80211:     (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
cfg80211:     (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:     (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:     (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:     (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
ip_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 24
nf_conntrack version 0.5.0 (459 buckets, 1836 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
xt_time: kernel timezone is -0000
        Hooked IMQ after mangle on PREROUTING
        Hooked IMQ after nat on POSTROUTING
IMQ driver loaded successfully.
ip_set version 4 loaded
Ebtables v2.0 registered
usbcore: registered new interface driver cdc_acm
cdc_acm: v0.26:USB Abstract Control Model driver for USB modems and ISDN adapters
usbcore: registered new interface driver usblp
usbcore: registered new interface driver usbserial
USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
usbserial: USB Serial Driver core
usbcore: registered new interface driver ums-alauda
usbcore: registered new interface driver ums-cypress
usbcore: registered new interface driver ums-datafab
usbcore: registered new interface driver ums-freecom
usbcore: registered new interface driver ums-isd200
usbcore: registered new interface driver ums-jumpshot
usbcore: registered new interface driver ums-karma
usbcore: registered new interface driver ums-sddr09
usbcore: registered new interface driver ums-sddr55
usbcore: registered new interface driver ums-usbat
USB Serial support registered for GSM modem (1-port)
usbcore: registered new interface driver option
option: v0.7.2:USB Driver for GSM modems
USB Serial support registered for Sierra USB modem
usbcore: registered new interface driver sierra
sierra: v.1.3.8:USB Driver for Sierra Wireless USB modems
fuse init (API version 7.13)
Adding 199012k swap on /dev/sda2.  Priority:-1 extents:1 across:199012k
EXT3-fs: sdb1: couldn't mount because of unsupported optional features (240).
device wlan0 entered promiscuous mode
br-lan: port 2(wlan0) entering forwarding state
device wlan0 left promiscuous mode
br-lan: port 2(wlan0) entering disabled state
device wlan0 entered promiscuous mode
br-lan: port 2(wlan0) entering forwarding state
ipt_bandwidth: timezone shift of 60 minutes detected, adjusting
               old minutes west=0, new minutes west=-60
EXT4-fs (sdb1): get root inode failed
EXT4-fs (sdb1): mount failed
ar71xx-wdt: enabling watchdog timer
root@Gargoyle:~$
root@Gargoyle:~$ df -h
Filesystem                Size      Used Available Use% Mounted on
/dev/root                 4.0M      4.0M         0 100% /rom
tmpfs                    14.3M    104.0K     14.2M   1% /tmp
tmpfs                   512.0K         0    512.0K   0% /dev
/dev/sda1               715.1M     28.6M    650.2M   4% /overlay
mini_fo:/overlay          4.0M      4.0M         0 100% /
root@Gargoyle:~$

dodam iz kupilem routerka godz. temu i nawet nie zdazylem poznac oryginalny soft może to mieć znaczenie?
hub rowniez najtansza chinszczyzna z all...

2 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 115,895

Odp: Hub z alle... za 5 zł nie wykrywa dysku

Zrobiłeś extroota.

sdb1 nie obsłuży bo coś z nim nie tak. Czym jest sdb1?

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

3 Odpowiedź przez helmut77

  • Zarejestrowany: 2012-03-28
  • Posty: 37

Odp: Hub z alle... za 5 zł nie wykrywa dysku

Cezary napisał/a:

Zrobiłeś extroota.

sdb1 nie obsłuży bo coś z nim nie tak. Czym jest sdb1?

hdd 320gb podlaczony do huba

4 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 115,895

Odp: Hub z alle... za 5 zł nie wykrywa dysku

Jaki system plików na nim?

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

5 Odpowiedź przez helmut77

  • Zarejestrowany: 2012-03-28
  • Posty: 37

Odp: Hub z alle... za 5 zł nie wykrywa dysku

Cezary napisał/a:

Jaki system plików na nim?

ext3

6 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 115,895

Odp: Hub z alle... za 5 zł nie wykrywa dysku

W takcie działania - odłącz go od huba, przyłącz ponownie. Zobacz czy jest /dev/sdb1 (ls /dev/sdb*)

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

7 Odpowiedź przez helmut77

  • Zarejestrowany: 2012-03-28
  • Posty: 37

Odp: Hub z alle... za 5 zł nie wykrywa dysku

Cezary napisał/a:

(ls /dev/sdb*)

chyba o to chodzi

root@Gargoyle:~$ ls /dev/sdb1
/dev/sdb1
root@Gargoyle:~$

8 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 115,895

Odp: Hub z alle... za 5 zł nie wykrywa dysku

No to jest.

mkdir /tmp/dysk
mount -t ext3 /dev/sdb1 /tmp/dysk
ls  /tmp/dysk/*

Działa?

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

9 Odpowiedź przez helmut77

  • Zarejestrowany: 2012-03-28
  • Posty: 37

Odp: Hub z alle... za 5 zł nie wykrywa dysku

Cezary napisał/a:

No to jest.

mkdir /tmp/dysk
mount -t ext3 /dev/sdb1 /tmp/dysk
ls  /tmp/dysk/*

Działa?

tak to wpisałem 

root@Gargoyle:~$ mkdir /tmp/dysk
root@Gargoyle:~$ mount -t ext3 /dev/sdb1 /tmp/dysk
root@Gargoyle:~$ ls  /tmp/dysk/*
ls: /tmp/dysk/*: No such file or directory
root@Gargoyle:~$

może tu coś poknociłęm mój fstab

config global automount
    option from_fstab 1
    option anon_mount 1
    
config global autoswap
    option from_fstab 1
    option anon_swap 0
    
config mount
    option target    /home
    option device    /dev/sda1
    option fstype    ext3
    option options    rw,sync
    option enabled    0
    option enabled_fsck 0

config swap
    option device    /dev/sda2
    option enabled    1
    option uuid 5411cedc-9ac6-422f-a44d-0ea729021765

config mount
    option target /mnt/hdd1    
    option device /dev/sdb1
    option uuid ff6808f9-0b62-40c0-a4ed-319749ad8a8f
    option fstype ext3
    option options rw,sync
    option enabled  1    
    option enabled_fsck 1

blkid

root@Gargoyle:~$ blkid
/dev/sdb1: UUID="ff6808f9-0b62-40c0-a4ed-319749ad8a8f"
/dev/sda2: UUID="5411cedc-9ac6-422f-a44d-0ea729021765"
/dev/sda1: UUID="1fb8b341-29b1-4a3f-b861-42d44eb8448b"
root@Gargoyle:~$

10 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 115,895

Odp: Hub z alle... za 5 zł nie wykrywa dysku

Mount pokazuje zamontowany sdb1?

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

11 Odpowiedź przez helmut77

  • Zarejestrowany: 2012-03-28
  • Posty: 37

Odp: Hub z alle... za 5 zł nie wykrywa dysku

Cezary napisał/a:

Mount pokazuje zamontowany sdb1?

no wlasnie ze nie

root@Gargoyle:~$ mount
rootfs on / type rootfs (rw)
/dev/root on /rom type squashfs (ro,relatime)
proc on /proc type proc (rw,relatime)
sysfs on /sys type sysfs (rw,relatime)
tmpfs on /tmp type tmpfs (rw,nosuid,nodev,relatime,size=14692k)
tmpfs on /dev type tmpfs (rw,relatime,size=512k,mode=755)
devpts on /dev/pts type devpts (rw,relatime,mode=600)
/dev/sda1 on /overlay type ext3 (rw,noatime,errors=continue,data=writeback)
mini_fo:/overlay on / type mini_fo (rw,relatime)
debugfs on /sys/kernel/debug type debugfs (rw,relatime)
none on /proc/bus/usb type usbfs (rw,relatime)
root@Gargoyle:~$

12 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 115,895

Odp: Hub z alle... za 5 zł nie wykrywa dysku

Zawartość logread ?
I jeszcze wynik

disktype /dev/sdb

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

13 Odpowiedź przez helmut77

  • Zarejestrowany: 2012-03-28
  • Posty: 37

Odp: Hub z alle... za 5 zł nie wykrywa dysku

Cezary napisał/a:

Zawartość logread ?
I jeszcze wynik

disktype /dev/sdb

disktype

root@Gargoyle:~$ disktype /dev/sdb

--- /dev/sdb
Block device, size 298.1 GiB (320072933376 bytes)
DOS/MBR partition map
Partition 1: 298.1 GiB (320070288384 bytes, 625137282 sectors from 63)
  Type 0x83 (Linux)
  Ext4 file system
    UUID FF6808F9-0B62-40C0-A4ED-319749AD8A8F (DCE, v4)
    Last mounted at "/overlay"
    Volume size 191.5 GiB (205631967232 bytes, 50203117 blocks of 4 KiB)

root@Gargoyle:~$

logread

Mar 28 18:51:39 Gargoyle user.err kernel: Buffer I/O error on device sdb1, logical block 3
Mar 28 18:51:39 Gargoyle user.err kernel: Buffer I/O error on device sdb1, logical block 4
Mar 28 18:51:39 Gargoyle user.err kernel: Buffer I/O error on device sdb1, logical block 5
Mar 28 18:51:39 Gargoyle user.err kernel: Buffer I/O error on device sdb1, logical block 6
Mar 28 18:51:39 Gargoyle user.info kernel: usb 1-1.4: USB disconnect, address 5
Mar 28 18:51:43 Gargoyle user.info kernel: Adding 199012k swap on /dev/sda2.  Priority:-1 extents:1 across:199012k
Mar 28 18:51:45 Gargoyle user.info kernel: Adding 199012k swap on /dev/sda2.  Priority:-1 extents:1 across:199012k
Mar 28 18:52:01 Gargoyle user.info kernel: usb 1-1.4: new full speed USB device using ar71xx-ehci and address 6
Mar 28 18:52:01 Gargoyle user.info kernel: usb 1-1.4: not running at top speed; connect to a high speed hub
Mar 28 18:52:01 Gargoyle user.info kernel: usb 1-1.4: configuration #1 chosen from 1 choice
Mar 28 18:52:01 Gargoyle user.info kernel: scsi3 : SCSI emulation for USB Mass Storage devices
Mar 28 18:52:01 Gargoyle user.debug kernel: usb-storage: device found at 6
Mar 28 18:52:01 Gargoyle user.debug kernel: usb-storage: waiting for device to settle before scanning
Mar 28 18:52:02 Gargoyle user.notice usb-modeswitch: 1-1.4:1.0: Manufacturer=Sunplus_Innovation_Technology Product=USB_to_Serial-ATA_bridge Serial=FFFACFF0FF080927FB2400FEC916FA
Mar 28 18:52:06 Gargoyle user.notice kernel: scsi 3:0:0:0: Direct-Access     Hitachi  HTS543232L9A300  0200 PQ: 0 ANSI: 4
Mar 28 18:52:06 Gargoyle user.debug kernel: usb-storage: device scan complete
Mar 28 18:52:06 Gargoyle user.notice kernel: sd 3:0:0:0: [sdb] 625142448 512-byte logical blocks: (320 GB/298 GiB)
Mar 28 18:52:06 Gargoyle user.notice kernel: sd 3:0:0:0: [sdb] Write Protect is off
Mar 28 18:52:06 Gargoyle user.debug kernel: sd 3:0:0:0: [sdb] Mode Sense: 38 00 00 00
Mar 28 18:52:06 Gargoyle user.err kernel: sd 3:0:0:0: [sdb] Assuming drive cache: write through
Mar 28 18:52:07 Gargoyle user.err kernel: sd 3:0:0:0: [sdb] Assuming drive cache: write through
Mar 28 18:52:07 Gargoyle user.info kernel:  sdb: sdb1
Mar 28 18:52:07 Gargoyle user.err kernel: sd 3:0:0:0: [sdb] Assuming drive cache: write through
Mar 28 18:52:07 Gargoyle user.notice kernel: sd 3:0:0:0: [sdb] Attached SCSI disk
Mar 28 18:52:09 Gargoyle user.info kernel: Adding 199012k swap on /dev/sda2.  Priority:-1 extents:1 across:199012k
Mar 28 18:52:13 Gargoyle user.notice fstab: e2fsck (/dev/sdb1): /dev/sdb1 contains a file system with errors, check forced.
Mar 28 18:52:14 Gargoyle user.notice fstab: e2fsck (/dev/sdb1): /dev/sdb1: Resize inode not valid.
Mar 28 18:52:14 Gargoyle user.notice fstab: e2fsck (/dev/sdb1): /dev/sdb1: UNEXPECTED INCONSISTENCY; RUN fsck MANUALLY.
Mar 28 18:52:14 Gargoyle user.notice fstab: e2fsck (/dev/sdb1):         (i.e., without -a or -p options)
Mar 28 18:52:14 Gargoyle user.info kernel: sd 3:0:0:0: [sdb] Unhandled error code
Mar 28 18:52:14 Gargoyle user.info kernel: sd 3:0:0:0: [sdb] Result: hostbyte=0x07 driverbyte=0x00
Mar 28 18:52:14 Gargoyle user.info kernel: sd 3:0:0:0: [sdb] CDB: cdb[0]=0x28: 28 00 00 00 00 00 00 00 20 00
Mar 28 18:52:14 Gargoyle user.err kernel: end_request: I/O error, dev sdb, sector 0
Mar 28 18:52:14 Gargoyle user.warn kernel: __ratelimit: 6 callbacks suppressed
Mar 28 18:52:14 Gargoyle user.err kernel: Buffer I/O error on device sdb, logical block 0
Mar 28 18:52:14 Gargoyle user.err kernel: Buffer I/O error on device sdb, logical block 1
Mar 28 18:52:14 Gargoyle user.err kernel: Buffer I/O error on device sdb, logical block 2
Mar 28 18:52:14 Gargoyle user.err kernel: Buffer I/O error on device sdb, logical block 3
Mar 28 18:52:14 Gargoyle user.info kernel: usb 1-1.4: USB disconnect, address 6
Mar 28 18:52:14 Gargoyle user.info kernel: scsi 3:0:0:0: [sdb] Unhandled error code
Mar 28 18:52:14 Gargoyle user.info kernel: scsi 3:0:0:0: [sdb] Result: hostbyte=0x07 driverbyte=0x00
Mar 28 18:52:14 Gargoyle user.info kernel: scsi 3:0:0:0: [sdb] CDB: cdb[0]=0x28: 28 00 00 00 00 00 00 00 08 00
Mar 28 18:52:14 Gargoyle user.err kernel: end_request: I/O error, dev sdb, sector 0
Mar 28 18:52:14 Gargoyle user.err kernel: Buffer I/O error on device sdb, logical block 0
Mar 28 18:52:17 Gargoyle user.info kernel: Adding 199012k swap on /dev/sda2.  Priority:-1 extents:1 across:199012k
Mar 28 18:52:19 Gargoyle user.info kernel: Adding 199012k swap on /dev/sda2.  Priority:-1 extents:1 across:199012k
Mar 28 18:52:21 Gargoyle user.info kernel: Adding 199012k swap on /dev/sda2.  Priority:-1 extents:1 across:199012k
Mar 28 18:52:36 Gargoyle user.info kernel: usb 1-1.4: new full speed USB device using ar71xx-ehci and address 7
Mar 28 18:52:36 Gargoyle user.info kernel: usb 1-1.4: not running at top speed; connect to a high speed hub
Mar 28 18:52:36 Gargoyle user.info kernel: usb 1-1.4: configuration #1 chosen from 1 choice
Mar 28 18:52:36 Gargoyle user.info kernel: scsi4 : SCSI emulation for USB Mass Storage devices
Mar 28 18:52:36 Gargoyle user.debug kernel: usb-storage: device found at 7
Mar 28 18:52:36 Gargoyle user.debug kernel: usb-storage: waiting for device to settle before scanning
Mar 28 18:52:36 Gargoyle user.notice usb-modeswitch: 1-1.4:1.0: Manufacturer=Sunplus_Innovation_Technology Product=USB_to_Serial-ATA_bridge Serial=FFFACFF0FF080927FB2400FEC916FA
Mar 28 18:52:41 Gargoyle user.notice kernel: scsi 4:0:0:0: Direct-Access     Hitachi  HTS543232L9A300  0200 PQ: 0 ANSI: 4
Mar 28 18:52:41 Gargoyle user.debug kernel: usb-storage: device scan complete
Mar 28 18:52:41 Gargoyle user.notice kernel: sd 4:0:0:0: [sdb] 625142448 512-byte logical blocks: (320 GB/298 GiB)
Mar 28 18:52:41 Gargoyle user.notice kernel: sd 4:0:0:0: [sdb] Write Protect is off
Mar 28 18:52:41 Gargoyle user.debug kernel: sd 4:0:0:0: [sdb] Mode Sense: 38 00 00 00
Mar 28 18:52:41 Gargoyle user.err kernel: sd 4:0:0:0: [sdb] Assuming drive cache: write through
Mar 28 18:52:41 Gargoyle user.err kernel: sd 4:0:0:0: [sdb] Assuming drive cache: write through
Mar 28 18:52:41 Gargoyle user.info kernel:  sdb: sdb1
Mar 28 18:52:41 Gargoyle user.err kernel: sd 4:0:0:0: [sdb] Assuming drive cache: write through
Mar 28 18:52:41 Gargoyle user.notice kernel: sd 4:0:0:0: [sdb] Attached SCSI disk
Mar 28 18:52:43 Gargoyle user.info kernel: Adding 199012k swap on /dev/sda2.  Priority:-1 extents:1 across:199012k
Mar 28 18:52:47 Gargoyle user.notice fstab: e2fsck (/dev/sdb1): /dev/sdb1 contains a file system with errors, check forced.
Mar 28 18:52:47 Gargoyle user.notice fstab: e2fsck (/dev/sdb1): /dev/sdb1: Resize inode not valid.
Mar 28 18:52:47 Gargoyle user.notice fstab: e2fsck (/dev/sdb1): /dev/sdb1: UNEXPECTED INCONSISTENCY; RUN fsck MANUALLY.
Mar 28 18:52:47 Gargoyle user.notice fstab: e2fsck (/dev/sdb1):         (i.e., without -a or -p options)
Mar 28 18:52:49 Gargoyle user.err kernel: EXT3-fs: sdb1: couldn't mount because of unsupported optional features (240).
Mar 28 18:52:52 Gargoyle user.err kernel: EXT4-fs (sdb1): get root inode failed
Mar 28 18:52:52 Gargoyle user.err kernel: EXT4-fs (sdb1): mount failed
Mar 28 18:52:52 Gargoyle user.info kernel: Adding 199012k swap on /dev/sda2.  Priority:-1 extents:1 across:199012k
Mar 28 18:56:51 Gargoyle user.info kernel: usb 1-1.4: USB disconnect, address 7
Mar 28 18:56:53 Gargoyle user.info kernel: Adding 199012k swap on /dev/sda2.  Priority:-1 extents:1 across:199012k
Mar 28 18:56:55 Gargoyle user.info kernel: Adding 199012k swap on /dev/sda2.  Priority:-1 extents:1 across:199012k
Mar 28 18:57:14 Gargoyle daemon.info hostapd: wlan0: STA 00:21:5d:38:bb:06 WPA: group key handshake completed (RSN)
Mar 28 18:57:14 Gargoyle daemon.info hostapd: wlan0: STA 00:22:58:55:28:e5 WPA: group key handshake completed (RSN)
Mar 28 18:58:57 Gargoyle user.info kernel: usb 1-1.4: new full speed USB device using ar71xx-ehci and address 8
Mar 28 18:58:58 Gargoyle user.info kernel: usb 1-1.4: not running at top speed; connect to a high speed hub
Mar 28 18:58:58 Gargoyle user.info kernel: usb 1-1.4: configuration #1 chosen from 1 choice
Mar 28 18:58:58 Gargoyle user.info kernel: scsi5 : SCSI emulation for USB Mass Storage devices
Mar 28 18:58:58 Gargoyle user.debug kernel: usb-storage: device found at 8
Mar 28 18:58:58 Gargoyle user.debug kernel: usb-storage: waiting for device to settle before scanning
Mar 28 18:58:58 Gargoyle user.notice usb-modeswitch: 1-1.4:1.0: Manufacturer=Sunplus_Innovation_Technology Product=USB_to_Serial-ATA_bridge Serial=301123456789
Mar 28 18:59:03 Gargoyle user.notice kernel: scsi 5:0:0:0: Direct-Access     SPIF30x  USB2SATA Bridge  0132 PQ: 0 ANSI: 2
Mar 28 18:59:03 Gargoyle user.debug kernel: usb-storage: device scan complete
Mar 28 18:59:03 Gargoyle user.notice kernel: sd 5:0:0:0: [sdb] Attached SCSI removable disk
Mar 28 18:59:04 Gargoyle user.info kernel: usb 1-1.4: USB disconnect, address 8
Mar 28 18:59:04 Gargoyle user.info kernel: usb 1-1.2: reset full speed USB device using ar71xx-ehci and address 3
Mar 28 18:59:05 Gargoyle user.info kernel: usb 1-1.4: new full speed USB device using ar71xx-ehci and address 9
Mar 28 18:59:05 Gargoyle user.info kernel: Adding 199012k swap on /dev/sda2.  Priority:-1 extents:1 across:199012k
Mar 28 18:59:07 Gargoyle user.info kernel: Adding 199012k swap on /dev/sda2.  Priority:-1 extents:1 across:199012k
Mar 28 18:59:09 Gargoyle user.err kernel: hub 1-1:1.0: unable to enumerate USB device on port 4
Mar 28 18:59:12 Gargoyle user.info kernel: usb 1-1.4: new full speed USB device using ar71xx-ehci and address 10
Mar 28 18:59:12 Gargoyle user.info kernel: usb 1-1.4: not running at top speed; connect to a high speed hub
Mar 28 18:59:12 Gargoyle user.info kernel: usb 1-1.4: configuration #1 chosen from 1 choice
Mar 28 18:59:12 Gargoyle user.info kernel: scsi6 : SCSI emulation for USB Mass Storage devices
Mar 28 18:59:12 Gargoyle user.debug kernel: usb-storage: device found at 10
Mar 28 18:59:12 Gargoyle user.debug kernel: usb-storage: waiting for device to settle before scanning
Mar 28 18:59:13 Gargoyle user.notice usb-modeswitch: 1-1.4:1.0: Manufacturer=Sunplus_Innovation_Technology Product=USB_to_Serial-ATA_bridge Serial=FFFACFF0FF080927FB2400FEC916FA
Mar 28 18:59:17 Gargoyle user.notice kernel: scsi 6:0:0:0: Direct-Access     Hitachi  HTS543232L9A300  0200 PQ: 0 ANSI: 4
Mar 28 18:59:17 Gargoyle user.debug kernel: usb-storage: device scan complete
Mar 28 18:59:17 Gargoyle user.notice kernel: sd 6:0:0:0: [sdb] 625142448 512-byte logical blocks: (320 GB/298 GiB)
Mar 28 18:59:17 Gargoyle user.notice kernel: sd 6:0:0:0: [sdb] Write Protect is off
Mar 28 18:59:17 Gargoyle user.debug kernel: sd 6:0:0:0: [sdb] Mode Sense: 38 00 00 00
Mar 28 18:59:17 Gargoyle user.err kernel: sd 6:0:0:0: [sdb] Assuming drive cache: write through
Mar 28 18:59:17 Gargoyle user.err kernel: sd 6:0:0:0: [sdb] Assuming drive cache: write through
Mar 28 18:59:17 Gargoyle user.info kernel:  sdb: sdb1
Mar 28 18:59:17 Gargoyle user.err kernel: sd 6:0:0:0: [sdb] Assuming drive cache: write through
Mar 28 18:59:17 Gargoyle user.notice kernel: sd 6:0:0:0: [sdb] Attached SCSI disk
Mar 28 18:59:19 Gargoyle user.info kernel: Adding 199012k swap on /dev/sda2.  Priority:-1 extents:1 across:199012k
Mar 28 18:59:23 Gargoyle user.notice fstab: e2fsck (/dev/sdb1): /dev/sdb1 contains a file system with errors, check forced.
Mar 28 18:59:24 Gargoyle user.notice fstab: e2fsck (/dev/sdb1): /dev/sdb1: Resize inode not valid.
Mar 28 18:59:24 Gargoyle user.notice fstab: e2fsck (/dev/sdb1): /dev/sdb1: UNEXPECTED INCONSISTENCY; RUN fsck MANUALLY.
Mar 28 18:59:24 Gargoyle user.notice fstab: e2fsck (/dev/sdb1):         (i.e., without -a or -p options)
Mar 28 18:59:25 Gargoyle user.err kernel: EXT3-fs: sdb1: couldn't mount because of unsupported optional features (240).
Mar 28 18:59:28 Gargoyle user.err kernel: EXT4-fs (sdb1): get root inode failed
Mar 28 18:59:28 Gargoyle user.err kernel: EXT4-fs (sdb1): mount failed
Mar 28 18:59:28 Gargoyle user.info kernel: Adding 199012k swap on /dev/sda2.  Priority:-1 extents:1 across:199012k
root@Gargoyle:~$

14 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 115,895

Odp: Hub z alle... za 5 zł nie wykrywa dysku

Ext4 a nie ext3. I zawiera błędy które automat nie potrafi naprawić i ręcznie mu trzeba e2fsck zrobić.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

15 Odpowiedź przez qwerty

  • qwerty
  • Użytkownik
  • Nieaktywny
  • Skąd: 2001:6a0:200:250::2/64
  • Zarejestrowany: 2010-07-19
  • Posty: 280

Odp: Hub z alle... za 5 zł nie wykrywa dysku

Czyżby partycja poszła do krainy zerowych bitów?:

Mar 28 18:59:23 Gargoyle user.notice fstab: e2fsck (/dev/sdb1): /dev/sdb1 contains a file system with errors, check forced.
Mar 28 18:59:24 Gargoyle user.notice fstab: e2fsck (/dev/sdb1): /dev/sdb1: Resize inode not valid.
Mar 28 18:59:24 Gargoyle user.notice fstab: e2fsck (/dev/sdb1): /dev/sdb1: UNEXPECTED INCONSISTENCY; RUN fsck MANUALLY.
Mar 28 18:59:24 Gargoyle user.notice fstab: e2fsck (/dev/sdb1):         (i.e., without -a or -p options)
Mar 28 18:59:25 Gargoyle user.err kernel: EXT3-fs: sdb1: couldn't mount because of unsupported optional features (240).
Mar 28 18:59:28 Gargoyle user.err kernel: EXT4-fs (sdb1): get root inode failed
Mar 28 18:59:28 Gargoyle user.err kernel: EXT4-fs (sdb1): mount failed

Wklep:
opkg update
opkg install e2fsprogs
i uruchom fsck

Mój net: http://www.speedtest.net/result/1920298676.png

16 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 115,895

Odp: Hub z alle... za 5 zł nie wykrywa dysku

EXT3-fs: sdb1: couldn't mount because of unsupported optional features (240). to jest akturat dlatego że tam ext4 jest a nie ext3. Ale sprawdzić trzeba.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

17 Odpowiedź przez helmut77

  • Zarejestrowany: 2012-03-28
  • Posty: 37

Odp: Hub z alle... za 5 zł nie wykrywa dysku

Cezary napisał/a:

Ext4 a nie ext3. I zawiera błędy które automat nie potrafi naprawić i ręcznie mu trzeba e2fsck zrobić.

to ciekawe bo formatowałem mkfs.ext3 /dev/sdb1 no ale nie wnikam

teraz po wsiskaniu y i naprawie mase cyfer mam i mieli dyskiem po ukonczeniu mam dac reboot ?

18 Odpowiedź przez LiO

  • LiO
  • LiO
  • Użytkownik
  • Nieaktywny
  • Skąd: Wrocław
  • Zarejestrowany: 2012-01-31
  • Posty: 376

Odp: Hub z alle... za 5 zł nie wykrywa dysku

nieee wink

http://klatka.ovh - CABANA PUBLIC SERVER
http://klatka.ovh/psi/ - phpsysinfo
http://temp.klatka.ovh/ - pogodynka

LiO's Strona

19 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 115,895

Odp: Hub z alle... za 5 zł nie wykrywa dysku

No nie. Jak naprawiłeś błedy to teraz po prostu go zamontuj tylko jako ext4.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

20 Odpowiedź przez helmut77 (edytowany przez helmut77 2012-03-28 19:35:41)

  • Zarejestrowany: 2012-03-28
  • Posty: 37

Odp: Hub z alle... za 5 zł nie wykrywa dysku

po wswzystkich poradach sukces

root@Gargoyle:~$ mount
rootfs on / type rootfs (rw)
/dev/root on /rom type squashfs (ro,relatime)
proc on /proc type proc (rw,relatime)
sysfs on /sys type sysfs (rw,relatime)
tmpfs on /tmp type tmpfs (rw,nosuid,nodev,relatime,size=14692k)
tmpfs on /dev type tmpfs (rw,relatime,size=512k,mode=755)
devpts on /dev/pts type devpts (rw,relatime,mode=600)
/dev/sda1 on /overlay type ext3 (rw,noatime,errors=continue,data=writeback)
mini_fo:/overlay on / type mini_fo (rw,relatime)
debugfs on /sys/kernel/debug type debugfs (rw,relatime)
none on /proc/bus/usb type usbfs (rw,relatime)
/dev/sdb1 on /tmp/usb_mount/ff6808f9-0b62-40c0-a4ed-319749ad8a8 type ext4 (rw,noatime,barrier=1,data=writeback)
root@Gargoyle:~$

teraz mam pytanko ten hub nie ma zasilania czy moge zasilic go z dreamboxa podlaczajac go wprost do usb ?
bo bez zasilania dysk nie chce ruszyc swieci sie tylko dioda

no i cos chyba z dyskiem po naprawie z 290gb zostalo 188 sad

root@Gargoyle:~$ df -h
Filesystem                Size      Used Available Use% Mounted on
/dev/root                 4.0M      4.0M         0 100% /rom
tmpfs                    14.3M    104.0K     14.2M   1% /tmp
tmpfs                   512.0K         0    512.0K   0% /dev
/dev/sda1               715.1M     33.6M    645.1M   5% /overlay
mini_fo:/overlay          4.0M      4.0M         0 100% /
/dev/sdb1               188.5G     62.9M    188.4G   0% /tmp/usb_mount/ff6808f9-0b62-40c0-a4ed-319749ad8a8
root@Gargoyle:~$

21 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 115,895

Odp: Hub z alle... za 5 zł nie wykrywa dysku

A hub pozwoli na taki numer z zasilaniem?

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

22 Odpowiedź przez helmut77

  • Zarejestrowany: 2012-03-28
  • Posty: 37

Odp: Hub z alle... za 5 zł nie wykrywa dysku

Cezary napisał/a:

A hub pozwoli na taki numer z zasilaniem?

po wlaczeniu kabla usb z dreama do huba dysk zaczol swirowac wlacza sie i wylacza zaraz wylaczylem po jeszcze cos skopce smile
jak to cholerstwo zasilic ?

aktualnie zasilam go neetbokiem z usb smile ale to sie mija z celem
zaraz pokuszam miernika i posprawdzam napiecia

23 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 115,895

Odp: Hub z alle... za 5 zł nie wykrywa dysku

Może masę masz różną (nie z tego samego gniazda) i przepięc dostaje.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona