FAQ o OpenWrt | Sprzedam różne routery | Oddam

kszaq · 2026-07-13 19:46:12

kszaq
Użytkownik
Nieaktywny

Zarejestrowany: 2013-06-16
Posty: 124

Odp: D-Link M30/CP (IDU dla Plusa)

nicefile napisał/a:

@kaszaq Może to nie wygląda oczywiste ale patrz na .dts i change implementujące Keenetic KN-3711 tam to działa mimo że widoczny jest split i brak partycji kernel

Przejrzałem jak wygląda KN-3711 i tam wygląda na to, że na początku UBI jest partycja kernel o stałym rozmiarze 6 MB, dzięki temu bootloader jest w stanie ją odczytać nawet jeśli pozostała zawartość pamięci jest sklejona z drugim firmware. W D-Link nie mamy osobnej partycji na kernel, przez co układ musi być odczytywalny przez u-boot.

pytonlon napisał/a:

@nicefile @kaszaq - czy mogę Wam jakoś pomóc przy rozszerzeniu wsparcia dla M60 -( problem z MAC z dwupacka i rozszerzenie partycji, etc) - nie mam takiego doświadczenia jak wy w tworzeniu PR; edycji dts, uczę się:) - ale służę egzemplarzem z dwupacka do testowania

Problem z MAC? Możesz napisać coś więcej?

W sprawie rozszerzenia miejsca, podaj co wypluwa Ci komenda

fw_printenv

pytonlon · 2026-07-13 22:41:09

pytonlon
Użytkownik
Nieaktywny

Skąd: KRK
Zarejestrowany: 2025-01-21
Posty: 15

Odp: D-Link M30/CP (IDU dla Plusa)

mac address

M60 dwupack

Box nr 1
odczytany mac za pomocą hexdump -v -n 6 -s 0x83 -e '5/1 "%02x:" 1/1 "%02x"' /dev/mtd6 daje dc:ea:e7:ae:ba:40;
etykieta dc:ea:e7:ae:ba:41
czyli zgodnie z informacjami z Commit b3ce08e
WAN dc:ea:e7:ae:ba:40
LAN dc:ea:e7:ae:ba:41
WLAN MAC(2.4) dc:ea:e7:ae:ba:42
WLAN MAC (5.0) dc:ea:e7:ae:ba:45

a system zwraca jak poniżej patrz output ip link

Box nr 2
odczytany mac za pomocą hexdump -v -n 6 -s 0x83 -e '5/1 "%02x:" 1/1 "%02x"' /dev/mtd6 daje dc:ea:e7:ae:ba:36;
etykieta dc:ea:e7:ae:ba:37
czyli zgodnie z informacjami z Commit b3ce08e
WAN dc:ea:e7:ae:ba:36
LAN dc:ea:e7:ae:ba:37
WLAN MAC(2.4) dc:ea:e7:ae:ba:38
WLAN MAC (5.0) dc:ea:e7:ae:ba:3b

a system też zwraca jak poniżej patrz output ip link

 
root@OpenWrt:~# ip link
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default qlen 1000
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1504 qdisc mq state UP mode DEFAULT group default qlen 1000
    link/ether 06:00:dc:ea:e7:af brd ff:ff:ff:ff:ff:ff
3: internet: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN mode DEFAULT group default qlen 1000
    link/ether 06:00:dc:ea:e7:ae brd ff:ff:ff:ff:ff:ff
4: lan1@eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue master br-lan state UP mode DEFAULT group default qlen 1000
    link/ether 06:00:dc:ea:e7:af brd ff:ff:ff:ff:ff:ff
5: lan2@eth0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc noqueue master br-lan state LOWERLAYERDOWN mode DEFAULT group default qlen 1000
    link/ether 06:00:dc:ea:e7:af brd ff:ff:ff:ff:ff:ff
6: lan3@eth0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc noqueue master br-lan state LOWERLAYERDOWN mode DEFAULT group default qlen 1000
    link/ether 06:00:dc:ea:e7:af brd ff:ff:ff:ff:ff:ff
7: lan4@eth0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc noqueue master br-lan state LOWERLAYERDOWN mode DEFAULT group default qlen 1000
    link/ether 06:00:dc:ea:e7:af brd ff:ff:ff:ff:ff:ff
8: br-lan: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP mode DEFAULT group default qlen 1000
    link/ether 06:00:dc:ea:e7:af brd ff:ff:ff:ff:ff:ff
9: phy0-ap0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue master br-lan state UP mode DEFAULT group default qlen 1000
    link/ether 06:00:dc:ea:e7:b0 brd ff:ff:ff:ff:ff:ff
10: phy1-ap0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue master br-lan state UP mode DEFAULT group default qlen 1000
    link/ether 06:00:dc:ea:e7:b3 brd ff:ff:ff:ff:ff:ff

wiec oba boxy są tak samo identyfikowane w sieci

pytonlon · 2026-07-13 22:44:42

pytonlon
Użytkownik
Nieaktywny

Skąd: KRK
Zarejestrowany: 2025-01-21
Posty: 15

Odp: D-Link M30/CP (IDU dla Plusa)

root@OpenWrt:~# fw_printenv
baudrate=115200
boot_by_part=if itest.s ${mupgrade_en} == 1; then aup;fi;if itest.s ${bootpart} == 0; then run set_act1;                                                              run ub0; else run set_act2; run ub1; fi
boot_by_tryactive=if itest.s ${sw_tryactive} == 0; then setenv sw_tryactive 2; setenv sw_active 1; saveen                                                             v; run ub0; else setenv sw_tryactive 2; setenv sw_active 2; saveenv; run ub1; fi
boot_rd_auto_sw_img=if itest.s ${sw_tryactive} == 2; then run boot_by_part; else run boot_by_tryactive; f                                                             i
bootargs=console=ttyS0,115200n1 loglevel=8 isolcpus=1 earlycon=uart8250,mmio32,0x11002000 bootpart=ubi0
bootdelay=2
bootmenu_0=Startup system (Default)=run boot_rd_auto_sw_img
bootmenu_1=Upgrade firmware=mtkupgrade fw
bootmenu_2=Upgrade ATF BL2=mtkupgrade bl2
bootmenu_3=Upgrade ATF FIP=mtkupgrade fip
bootmenu_4=Http Upgrade=uip main; reset
bootmenu_5=Upgrade single image=mtkupgrade simg
bootmenu_6=Load image=mtkload
bootpart=0
con=0
en_wdt=wdt on 30
ethact=ethernet@15100000
fdtcontroladdr=5ff3a000
fw_ver_a=V1.11B03
i=7
ipaddr=192.168.200.1
loadaddr=0x46000000
mtdids=nmbm0=nmbm0
mtdparts=nmbm0:1024k(bl2),512k(u-boot-env),2048k(factory),2048k(fip),51200k(ubi),51200k(ubi1),256k(Odm),5                                                             12k(Config1),512k(Config2),5120k(Storage)
mupgrade_en=1
netmask=255.255.255.0
power_on_rst_recov=setexpr i 8;setexpr con 1;while itest ${con} -gt 0; do  if gpio input 10; then   gpio                                                              toggle 44; else   setexpr con 0; fi; sleep 1; if itest ${i} -eq 0; then   setexpr con 0; else   setexpr i                                                              ${i} - 1; fi;done;if itest ${i} -gt 0; then  if itest ${i} -lt 4; then   setenv FW_RESET_FLAG 1; saveenv                                                             ;  echo set FW_RESET_FLAG to 1;  gpio toggle 44;sleep 0.2;  gpio toggle 44;sleep 0.2;  gpio toggle 44;sle                                                             ep 0.2;  gpio toggle 44;sleep 0.2;  gpio toggle 44;sleep 0.2;  gpio toggle 44; fi;else  uip main;fi
serverip=192.168.200.2
set_act1=if itest.s ${sw_active} != 1; then setenv sw_active 1; saveenv; fi
set_act2=if itest.s ${sw_active} != 2; then setenv sw_active 2; saveenv; fi
stderr=serial@11002000
stdin=serial@11002000
stdout=serial@11002000
sw_active=1
sw_tryactive=2
ub0=setenv bootpart 0; mtkboardboot; run ub0to1; uip main; reset
ub0to1=setenv bootpart 1; mtkboardboot
ub1=setenv bootpart 1; mtkboardboot; run ub1to0; uip main; reset
ub1to0=setenv bootpart 0; mtkboardboot

do tego logread - wgrany build od Cezarego

BusyBox v1.37.0 (2026-03-26 13:35:28 UTC) built-in shell (ash)

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 -----------------------------------------------------------------------------
 |                                                                           |
 | OpenWrt 25.12-SNAPSHOT, r33032-b830633cb8 Dave's Guitar                   |
 |                                                                           |
 | Build time: 2026-06-26 17:11 UTC                                          |
 | Cezary Jackiewicz, https://eko.one.pl                                     |
 |                                                                           |
 -----------------------------------------------------------------------------

 === WARNING! ================================================================
 There is no root password defined on this device!
 Use the "passwd" command to set up a new password
 in order to prevent unauthorized SSH logins.
 -----------------------------------------------------------------------------

 | Machine: D-Link AQUILA PRO AI M60 A1                                      |
 | Uptime: 0d, 00:00:27                                                      |
 | Load: 0.39 0.09 0.03                                                      |
 | Flash: total: 29.6MB, free: 27.9MB, used: 0%                              |
 | Memory: total: 484.1MB, free: 396.3MB, used: 18%                          |
 | Leases: 0                                                                 |
 | lan: static, 192.168.1.1                                                  |
 | wan: dhcp, ?                                                              |
 | wan6: dhcpv6, ?                                                           |
 | radio0: lan, mode: ap, ssid: OpenWrt, channel: 1, conn: 0                 |
 | radio1: lan, mode: ap, ssid: OpenWrt, channel: 36, conn: 0                |
 -----------------------------------------------------------------------------
 | CPU temp: 42.60 C                                                         |
 | Wi-Fi chip temp: 46.00 C, 48.00 C                                         |
 | Ethernet chip temp: 40.08 C                                               |
 -----------------------------------------------------------------------------

 OpenWrt recently switched to the "apk" package manager!

 OPKG Command           APK Equivalent      Description
 -----------------------------------------------------------------------------
...
 -----------------------------------------------------------------------------

For more information visit:
https://openwrt.org/docs/guide-user/additional-software/opkg-to-apk-cheatsheet

root@OpenWrt:~# logread
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
Fri Jun 26 19:12:25 2026 kern.notice kernel: [    0.000000] Linux version 6.12.94 (cezary@eko.one.pl) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 14.3.0 r32355-02f9e71dd2) 14.3.0, GNU ld (GNU Binutils) 2.44) #0 SMP Fri Jun 26 17:02:25 2026
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.000000] Machine model: D-Link AQUILA PRO AI M60 A1
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.000000] earlycon: uart8250 at MMIO32 0x0000000011002000 (options '')
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.000000] printk: legacy bootconsole [uart8250] enabled
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.000000] OF: reserved mem: 0x0000000042ff0000..0x0000000042ffffff (64 KiB) map non-reusable ramoops@42ff0000
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.000000] OF: reserved mem: 0x0000000043000000..0x000000004303ffff (256 KiB) nomap non-reusable secmon@43000000
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.000000] OF: reserved mem: 0x000000004fc00000..0x000000004fcfffff (1024 KiB) nomap non-reusable wmcpu-reserved@4fc00000
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.000000] OF: reserved mem: 0x000000004fd00000..0x000000004fd3ffff (256 KiB) nomap non-reusable wo-emi@4fd00000
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.000000] OF: reserved mem: 0x000000004fd40000..0x000000004fd7ffff (256 KiB) nomap non-reusable wo-emi@4fd40000
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.000000] OF: reserved mem: 0x000000004fd80000..0x000000004ffbffff (2304 KiB) nomap non-reusable wo-data@4fd80000
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.000000] Zone ranges:
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.000000]   DMA      [mem 0x0000000040000000-0x000000005fffffff]
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.000000]   DMA32    empty
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.000000]   Normal   empty
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.000000] Movable zone start for each node
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.000000] Early memory node ranges
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.000000]   node   0: [mem 0x0000000040000000-0x0000000042ffffff]
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.000000]   node   0: [mem 0x0000000043000000-0x000000004303ffff]
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.000000]   node   0: [mem 0x0000000043040000-0x000000004fbfffff]
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.000000]   node   0: [mem 0x000000004fc00000-0x000000004ffbffff]
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.000000]   node   0: [mem 0x000000004ffc0000-0x000000005fffffff]
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000005fffffff]
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.000000] psci: probing for conduit method from DT.
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.000000] psci: PSCIv1.1 detected in firmware.
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.000000] psci: Using standard PSCI v0.2 function IDs
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.000000] psci: MIGRATE_INFO_TYPE not supported.
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.000000] psci: SMC Calling Convention v1.2
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.000000] percpu: Embedded 20 pages/cpu s42648 r8192 d31080 u81920
Fri Jun 26 19:12:25 2026 kern.debug kernel: [    0.000000] pcpu-alloc: s42648 r8192 d31080 u81920 alloc=20*4096
Fri Jun 26 19:12:25 2026 kern.debug kernel: [    0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.000000] Detected VIPT I-cache on CPU0
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.000000] CPU features: detected: GIC system register CPU interface
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.000000] CPU features: kernel page table isolation disabled by kernel configuration
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.000000] alternatives: applying boot alternatives
Fri Jun 26 19:12:25 2026 kern.notice kernel: [    0.000000] Kernel command line: console=ttyS0,115200n1 loglevel=8 isolcpus=1 earlycon=uart8250,mmio32,0x11002000 bootpart=ubi0
Fri Jun 26 19:12:25 2026 kern.notice kernel: [    0.000000] Unknown kernel command line parameters "isolcpus=1 bootpart=ubi0", will be passed to user space.
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.000000] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes, linear)
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.000000] Inode-cache hash table entries: 32768 (order: 6, 262144 bytes, linear)
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 131072
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.000000] software IO TLB: SWIOTLB bounce buffer size adjusted to 0MB
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.000000] software IO TLB: area num 4.
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.000000] software IO TLB: SWIOTLB bounce buffer size roundup to 1MB
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.000000] software IO TLB: mapped [mem 0x000000005f4c0000-0x000000005f5c0000] (1MB)
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.000000] rcu: Hierarchical RCU implementation.
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.000000]       Tracing variant of Tasks RCU enabled.
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.000000] RCU Tasks Trace: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=4.
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.000000] GICv3: GIC: Using split EOI/Deactivate mode
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.000000] GICv3: 640 SPIs implemented
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.000000] GICv3: 0 Extended SPIs implemented
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.000000] Root IRQ handler: 0xffffffc080010080
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.000000] GICv3: GICv3 features: 16 PPIs
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.000000] GICv3: GICD_CTRL.DS=0, SCR_EL3.FIQ=0
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.000000] GICv3: CPU0: found redistributor 0 region 0:0x000000000c080000
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.000000] arch_timer: cp15 timer(s) running at 13.00MHz (phys).
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2ff89eacb, max_idle_ns: 440795202429 ns
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.000000] sched_clock: 56 bits at 13MHz, resolution 76ns, wraps every 4398046511101ns
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.008130] Calibrating delay loop (skipped), value calculated using timer frequency.. 26.00 BogoMIPS (lpj=130000)
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.018533] pid_max: default: 32768 minimum: 301
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.025122] Mount-cache hash table entries: 1024 (order: 1, 8192 bytes, linear)
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.032470] Mountpoint-cache hash table entries: 1024 (order: 1, 8192 bytes, linear)
Fri Jun 26 19:12:25 2026 kern.warn kernel: [    0.041818] cacheinfo: Unable to detect cache hierarchy for CPU 0
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.048529] rcu: Hierarchical SRCU implementation.
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.053337] rcu:  Max phase no-delay instances is 1000.
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.058713] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.067044] smp: Bringing up secondary CPUs ...
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.071856] Detected VIPT I-cache on CPU1
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.071897] GICv3: CPU1: found redistributor 1 region 0:0x000000000c0a0000
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.071924] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.072240] Detected VIPT I-cache on CPU2
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.072266] GICv3: CPU2: found redistributor 2 region 0:0x000000000c0c0000
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.072278] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.072577] Detected VIPT I-cache on CPU3
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.072600] GICv3: CPU3: found redistributor 3 region 0:0x000000000c0e0000
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.072610] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.072645] smp: Brought up 1 node, 4 CPUs
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.129184] SMP: Total of 4 processors activated.
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.133903] CPU: All CPU(s) started at EL2
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.138010] CPU features: detected: 32-bit EL0 Support
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.143168] CPU features: detected: CRC32 instructions
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.148341] alternatives: applying system-wide alternatives
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.154042] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.162550] Memory: 492284K/524288K available (9536K kernel code, 992K rwdata, 1832K rodata, 512K init, 316K bss, 29072K reserved, 0K cma-reserved)
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.178140] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.188044] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.195022] 29424 pages in range for non-PLT usage
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.195025] 520944 pages in range for PLT usage
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.200822] pinctrl core: initialized pinctrl subsystem
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.212336] NET: Registered PF_NETLINK/PF_ROUTE protocol family
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.218528] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.225635] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.233425] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.241708] thermal_sys: Registered thermal governor 'fair_share'
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.241712] thermal_sys: Registered thermal governor 'bang_bang'
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.247828] thermal_sys: Registered thermal governor 'step_wise'
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.253862] thermal_sys: Registered thermal governor 'user_space'
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.259944] ASID allocator initialised with 65536 entries
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.272187] pstore: Using crash dump compression: deflate
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.277610] pstore: Registered ramoops as persistent store backend
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.283814] ramoops: using 0x10000@0x42ff0000, ecc: 0
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.289846] /soc/interrupt-controller@c000000: Fixed dependency cycle(s) with /soc/interrupt-controller@c000000
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.311342] cryptd: max_cpu_qlen set to 1000
Fri Jun 26 19:12:25 2026 kern.notice kernel: [    0.316475] SCSI subsystem initialized
Fri Jun 26 19:12:25 2026 kern.debug kernel: [    0.320324] libata version 3.00 loaded.
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.325304] clocksource: Switched to clocksource arch_sys_counter
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.333016] NET: Registered PF_INET protocol family
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.338027] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear)
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.346325] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear)
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.354722] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.362512] TCP established hash table entries: 4096 (order: 3, 32768 bytes, linear)
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.370313] TCP bind hash table entries: 4096 (order: 5, 131072 bytes, linear)
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.377657] TCP: Hash tables configured (established 4096 bind 4096)
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.384187] MPTCP token hash table entries: 512 (order: 2, 12288 bytes, linear)
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.391608] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.398175] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.405308] NET: Registered PF_UNIX/PF_LOCAL protocol family
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.411008] PCI: CLS 0 bytes, default 64
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.416020] workingset: timestamp_bits=46 max_order=17 bucket_order=0
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.425934] squashfs: version 4.0 (2009/01/31) Phillip Lougher
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.431792] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.477161] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.488092] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.497186] printk: legacy console [ttyS0] disabled
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.522396] 11002000.serial: ttyS0 at MMIO 0x11002000 (irq = 116, base_baud = 2500000) is a ST16650V2
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.531693] printk: legacy console [ttyS0] enabled
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.541262] printk: legacy bootconsole [uart8250] disabled
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.555335] loop: module loaded
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.559946] spi-nand spi0.0: Macronix SPI NAND was found.
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.565372] spi-nand spi0.0: 128 MiB, block size: 128 KiB, page size: 2048, OOB size: 64
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.573952] Signature found at block 1023 [0x07fe0000]
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.579082] NMBM management region starts at block 960 [0x07800000]
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.586762] First info table with writecount 0 found in block 960
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.596945] Second info table with writecount 0 found in block 963
Fri Jun 26 19:12:25 2026 kern.info kernel: [    0.603112] NMBM has been successfully attached
Fri Jun 26 19:12:25 2026 kern.notice kernel: [    0.607906] 10 fixed-partitions partitions found on MTD device spi0.0
Fri Jun 26 19:12:25 2026 kern.notice kernel: [    0.614333] Creating 10 MTD partitions on "spi0.0":
Fri Jun 26 19:12:25 2026 kern.notice kernel: [    0.619199] 0x000000000000-0x000000100000 : "BL2"
Fri Jun 26 19:12:25 2026 kern.notice kernel: [    0.624723] 0x000000100000-0x000000180000 : "u-boot-env"
Fri Jun 26 19:12:25 2026 kern.notice kernel: [    0.630593] 0x000000180000-0x000000380000 : "Factory"
Fri Jun 26 19:12:25 2026 kern.notice kernel: [    0.637012] 0x000000380000-0x000000580000 : "FIP"
Fri Jun 26 19:12:25 2026 kern.notice kernel: [    0.642888] 0x000000580000-0x000003780000 : "ubi"
Fri Jun 26 19:12:25 2026 kern.notice kernel: [    0.670974] 0x000003780000-0x000006980000 : "ubi1"
Fri Jun 26 19:12:25 2026 kern.notice kernel: [    0.699234] 0x000006980000-0x0000069c0000 : "Odm"
Fri Jun 26 19:12:25 2026 kern.notice kernel: [    0.704487] 0x0000069c0000-0x000006a40000 : "Config1"
Fri Jun 26 19:12:25 2026 kern.notice kernel: [    0.710036] 0x000006a40000-0x000006ac0000 : "Config2"
Fri Jun 26 19:12:25 2026 kern.notice kernel: [    0.715580] 0x000006ac0000-0x0000074c0000 : "Storage"
Fri Jun 26 19:12:25 2026 kern.info kernel: [    3.426293] Maxlinear Ethernet GPY211C mdio-bus:06: Firmware Version: 8.111 (0x886F)
Fri Jun 26 19:12:25 2026 kern.info kernel: [    3.437502] mtk_soc_eth 15100000.ethernet eth0: mediatek frame engine at 0xffffffc081900000, irq 120
Fri Jun 26 19:12:25 2026 kern.info kernel: [    3.447299] mtk_soc_eth 15100000.ethernet eth1: mediatek frame engine at 0xffffffc081900000, irq 120
Fri Jun 26 19:12:25 2026 kern.info kernel: [    3.456948] i2c_dev: i2c /dev entries driver
Fri Jun 26 19:12:25 2026 kern.info kernel: [    3.463000] mtk-wdt 1001c000.watchdog: Watchdog enabled (timeout=31 sec, nowayout=0)
Fri Jun 26 19:12:25 2026 kern.info kernel: [    3.471768] NET: Registered PF_INET6 protocol family
Fri Jun 26 19:12:25 2026 kern.info kernel: [    3.477744] Segment Routing with IPv6
Fri Jun 26 19:12:25 2026 kern.info kernel: [    3.481426] In-situ OAM (IOAM) with IPv6
Fri Jun 26 19:12:25 2026 kern.info kernel: [    3.485405] NET: Registered PF_PACKET protocol family
Fri Jun 26 19:12:25 2026 kern.info kernel: [    3.490455] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
Fri Jun 26 19:12:25 2026 kern.info kernel: [    3.503487] 8021q: 802.1Q VLAN Support v1.8
Fri Jun 26 19:12:25 2026 kern.info kernel: [    3.573759] mt7530-mdio mdio-bus:1f: configuring for fixed/2500base-x link mode
Fri Jun 26 19:12:25 2026 kern.info kernel: [    3.582964] mt7530-mdio mdio-bus:1f: Link is Up - 2.5Gbps/Full - flow control rx/tx
Fri Jun 26 19:12:25 2026 kern.info kernel: [    3.592928] mt7530-mdio mdio-bus:1f lan1 (uninitialized): PHY [mt7530-0:00] driver [MediaTek MT7531 PHY] (irq=125)
Fri Jun 26 19:12:25 2026 kern.info kernel: [    3.614064] mt7530-mdio mdio-bus:1f lan2 (uninitialized): PHY [mt7530-0:01] driver [MediaTek MT7531 PHY] (irq=126)
Fri Jun 26 19:12:25 2026 kern.info kernel: [    3.634843] mt7530-mdio mdio-bus:1f lan3 (uninitialized): PHY [mt7530-0:02] driver [MediaTek MT7531 PHY] (irq=127)
Fri Jun 26 19:12:25 2026 kern.info kernel: [    3.655622] mt7530-mdio mdio-bus:1f lan4 (uninitialized): PHY [mt7530-0:03] driver [MediaTek MT7531 PHY] (irq=128)
Fri Jun 26 19:12:25 2026 kern.info kernel: [    3.666945] mtk_soc_eth 15100000.ethernet eth0: entered promiscuous mode
Fri Jun 26 19:12:25 2026 kern.info kernel: [    3.673651] DSA: tree 0 setup
Fri Jun 26 19:12:25 2026 kern.notice kernel: [    3.677131] UBI: auto-attach mtd4
Fri Jun 26 19:12:25 2026 kern.notice kernel: [    3.680446] ubi0: default fastmap pool size: 20
Fri Jun 26 19:12:25 2026 kern.notice kernel: [    3.684961] ubi0: default fastmap WL pool size: 10
Fri Jun 26 19:12:25 2026 kern.notice kernel: [    3.689753] ubi0: attaching mtd4
Fri Jun 26 19:12:25 2026 kern.notice kernel: [    3.991230] ubi0: scanning is finished
Fri Jun 26 19:12:25 2026 kern.notice kernel: [    4.002562] ubi0: attached mtd4 (name "ubi", size 50 MiB)
Fri Jun 26 19:12:25 2026 kern.notice kernel: [    4.007963] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
Fri Jun 26 19:12:25 2026 kern.notice kernel: [    4.014817] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
Fri Jun 26 19:12:25 2026 kern.notice kernel: [    4.021587] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
Fri Jun 26 19:12:25 2026 kern.notice kernel: [    4.028530] ubi0: good PEBs: 400, bad PEBs: 0, corrupted PEBs: 0
Fri Jun 26 19:12:25 2026 kern.notice kernel: [    4.034516] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
Fri Jun 26 19:12:25 2026 kern.notice kernel: [    4.041719] ubi0: max/mean erase counter: 208/127, WL threshold: 4096, image sequence number: 456261883
Fri Jun 26 19:12:25 2026 kern.notice kernel: [    4.051089] ubi0: available PEBs: 0, total reserved PEBs: 400, PEBs reserved for bad PEB handling: 19
Fri Jun 26 19:12:25 2026 kern.notice kernel: [    4.060292] ubi0: background thread "ubi_bgt0d" started, PID 682
Fri Jun 26 19:12:25 2026 kern.info kernel: [    4.061130] block ubiblock0_1: created from ubi0:1(rootfs)
Fri Jun 26 19:12:25 2026 kern.notice kernel: [    4.071755] ubiblock: device ubiblock0_1 (rootfs) set to be root filesystem
Fri Jun 26 19:12:25 2026 kern.info kernel: [    4.078788] clk: Disabling unused clocks
Fri Jun 26 19:12:25 2026 kern.info kernel: [    4.082938] PM: genpd: Disabling unused power domains
Fri Jun 26 19:12:25 2026 kern.info kernel: [    4.094005] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
Fri Jun 26 19:12:25 2026 kern.info kernel: [    4.101338] Freeing unused kernel memory: 512K
Fri Jun 26 19:12:25 2026 kern.info kernel: [    4.105823] Run /sbin/init as init process
Fri Jun 26 19:12:25 2026 kern.debug kernel: [    4.109902]   with arguments:
Fri Jun 26 19:12:25 2026 kern.debug kernel: [    4.112854]     /sbin/init
Fri Jun 26 19:12:25 2026 kern.debug kernel: [    4.115553]   with environment:
Fri Jun 26 19:12:25 2026 kern.debug kernel: [    4.118678]     HOME=/
Fri Jun 26 19:12:25 2026 kern.debug kernel: [    4.121023]     TERM=linux
Fri Jun 26 19:12:25 2026 kern.debug kernel: [    4.123715]     isolcpus=1
Fri Jun 26 19:12:25 2026 kern.debug kernel: [    4.126412]     bootpart=ubi0
Fri Jun 26 19:12:25 2026 user.info kernel: [    4.365293] init: Console is alive
Fri Jun 26 19:12:25 2026 user.info kernel: [    4.368825] init: - watchdog -
Fri Jun 26 19:12:25 2026 user.info kernel: [    4.722858] kmodloader: loading kernel modules from /etc/modules-boot.d/*
Fri Jun 26 19:12:25 2026 kern.warn kernel: [    4.739904] gpio_button_hotplug: loading out-of-tree module taints kernel.
Fri Jun 26 19:12:25 2026 kern.info kernel: [    4.749690] Enter gca230718_probe for device address 64
Fri Jun 26 19:12:25 2026 kern.info kernel: [    4.754915] Creating LED for node led: reg=0
Fri Jun 26 19:12:25 2026 kern.info kernel: [    4.759247] Creating LED for node led: reg=1
Fri Jun 26 19:12:25 2026 kern.info kernel: [    4.763533] Creating LED for node led: reg=2
Fri Jun 26 19:12:25 2026 kern.info kernel: [    4.767827] Creating LED for node led: reg=3
Fri Jun 26 19:12:25 2026 user.info kernel: [    4.776773] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
Fri Jun 26 19:12:25 2026 user.info kernel: [    4.785164] init: - preinit -
Fri Jun 26 19:12:25 2026 kern.info kernel: [    5.105496] mtk_soc_eth 15100000.ethernet internet: renamed from eth1
Fri Jun 26 19:12:25 2026 kern.info kernel: [    5.120298] mtk_soc_eth 15100000.ethernet eth0: configuring for fixed/2500base-x link mode
Fri Jun 26 19:12:25 2026 kern.info kernel: [    5.128771] mtk_soc_eth 15100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx
Fri Jun 26 19:12:25 2026 kern.info kernel: [    5.150359] mt7530-mdio mdio-bus:1f lan1: configuring for phy/gmii link mode
Fri Jun 26 19:12:25 2026 kern.notice kernel: [    9.382001] UBIFS (ubi0:2): Mounting in unauthenticated mode
Fri Jun 26 19:12:25 2026 kern.notice kernel: [    9.387741] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" started, PID 807
Fri Jun 26 19:12:25 2026 kern.notice kernel: [    9.427753] UBIFS (ubi0:2): recovery needed
Fri Jun 26 19:12:25 2026 kern.notice kernel: [    9.465311] random: crng init done
Fri Jun 26 19:12:25 2026 kern.notice kernel: [    9.565380] UBIFS (ubi0:2): recovery completed
Fri Jun 26 19:12:25 2026 kern.notice kernel: [    9.569868] UBIFS (ubi0:2): UBIFS: mounted UBI device 0, volume 2, name "rootfs_data"
Fri Jun 26 19:12:25 2026 kern.notice kernel: [    9.577685] UBIFS (ubi0:2): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
Fri Jun 26 19:12:25 2026 kern.notice kernel: [    9.587587] UBIFS (ubi0:2): FS size: 34410496 bytes (32 MiB, 271 LEBs), max 281 LEBs, journal size 1777664 bytes (1 MiB, 14 LEBs)
Fri Jun 26 19:12:25 2026 kern.notice kernel: [    9.599217] UBIFS (ubi0:2): reserved for root: 1625292 bytes (1587 KiB)
Fri Jun 26 19:12:25 2026 kern.notice kernel: [    9.605818] UBIFS (ubi0:2): media format: w5/r0 (latest is w5/r0), UUID C893B1D2-85C8-4F6C-8F5B-756DB88D404B, small LPT model
Fri Jun 26 19:12:25 2026 user.info kernel: [    9.621668] mount_root: switching to ubifs overlay
Fri Jun 26 19:12:25 2026 kern.warn kernel: [    9.631113] overlayfs: null uuid detected in lower fs '/', falling back to xino=off,index=off,nfs_export=off.
Fri Jun 26 19:12:25 2026 user.debug kernel: [    9.647644] urandom-seed: Seeding with /etc/urandom.seed
Fri Jun 26 19:12:25 2026 user.info kernel: [    9.706627] procd: - early -
Fri Jun 26 19:12:25 2026 user.info kernel: [    9.709557] procd: - watchdog -
Fri Jun 26 19:12:25 2026 user.info kernel: [   10.256084] procd: - watchdog -
Fri Jun 26 19:12:25 2026 user.info kernel: [   10.268516] procd: - ubus -
Fri Jun 26 19:12:25 2026 user.info kernel: [   10.423782] procd: - init -
Fri Jun 26 19:12:25 2026 user.info kernel: [   10.856599] urngd: v1.0.2 started.
Fri Jun 26 19:12:25 2026 user.info kernel: [   10.918791] kmodloader: loading kernel modules from /etc/modules.d/*
Fri Jun 26 19:12:25 2026 kern.info kernel: [   10.942724] tun: Universal TUN/TAP device driver, 1.6
Fri Jun 26 19:12:25 2026 kern.info kernel: [   10.956012] Loading modules backported from Linux version v6.18.26-0-g1fe060681
Fri Jun 26 19:12:25 2026 kern.info kernel: [   10.963317] Backport generated by backports.git 6ecbb44
Fri Jun 26 19:12:25 2026 kern.info kernel: [   11.360385] mt798x-wmac 18000000.wifi: HW/SW Version: 0x8a108a10, Build Time: 20240823160656a
Fri Jun 26 19:12:25 2026 kern.info kernel: [   11.528146] mt798x-wmac 18000000.wifi: WM Firmware Version: ____000000, Build Time: 20240823160721
Fri Jun 26 19:12:25 2026 kern.info kernel: [   11.621551] mt798x-wmac 18000000.wifi: WA Firmware Version: DEV_000000, Build Time: 20240823160840
Fri Jun 26 19:12:25 2026 kern.info kernel: [   11.728366] mt798x-wmac 18000000.wifi: registering led 'mt76-phy0'
Fri Jun 26 19:12:25 2026 kern.info kernel: [   11.776965] mt798x-wmac 18000000.wifi: registering led 'mt76-phy1'
Fri Jun 26 19:12:25 2026 kern.info kernel: [   11.859992] PPP generic driver version 2.4.2
Fri Jun 26 19:12:25 2026 kern.info kernel: [   11.865183] NET: Registered PF_PPPOX protocol family
Fri Jun 26 19:12:25 2026 kern.info kernel: [   11.872088] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information.
Fri Jun 26 19:12:25 2026 kern.info kernel: [   11.879952] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
Fri Jun 26 19:12:25 2026 user.info kernel: [   11.892263] kmodloader: done loading kernel modules from /etc/modules.d/*
Fri Jun 26 19:12:26 2026 user.notice dnsmasq: DNS rebinding protection is active, will discard upstream RFC1918 responses!
Fri Jun 26 19:12:26 2026 user.notice dnsmasq: Allowing 127.0.0.0/8 responses
Fri Jun 26 19:12:26 2026 daemon.info dnsmasq[1]: started, version 2.93 cachesize 1000
Fri Jun 26 19:12:26 2026 daemon.info dnsmasq[1]: DNS service limited to local subnets
Fri Jun 26 19:12:26 2026 daemon.info dnsmasq[1]: compile time options: IPv6 GNU-getopt no-DBus UBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-nftset no-auth no-DNSSEC no-ID loop-detect inotify dumpfile
Fri Jun 26 19:12:26 2026 daemon.info dnsmasq[1]: UBus support enabled: connected to system bus
Fri Jun 26 19:12:26 2026 daemon.info dnsmasq[1]: using only locally-known addresses for test
Fri Jun 26 19:12:26 2026 daemon.info dnsmasq[1]: using only locally-known addresses for onion
Fri Jun 26 19:12:26 2026 daemon.info dnsmasq[1]: using only locally-known addresses for localhost
Fri Jun 26 19:12:26 2026 daemon.info dnsmasq[1]: using only locally-known addresses for local
Fri Jun 26 19:12:26 2026 daemon.info dnsmasq[1]: using only locally-known addresses for invalid
Fri Jun 26 19:12:26 2026 daemon.info dnsmasq[1]: using only locally-known addresses for bind
Fri Jun 26 19:12:26 2026 daemon.info dnsmasq[1]: using only locally-known addresses for lan
Fri Jun 26 19:12:26 2026 daemon.warn dnsmasq[1]: no servers found in /tmp/resolv.conf.d/resolv.conf.auto, will retry
Fri Jun 26 19:12:26 2026 daemon.info dnsmasq[1]: read /etc/hosts - 12 names
Fri Jun 26 19:12:26 2026 daemon.info dnsmasq[1]: read /tmp/hosts/dhcp.cfg01411c - 0 names
Fri Jun 26 19:12:26 2026 authpriv.info dropbear[1648]: Not backgrounding
Fri Jun 26 19:12:27 2026 user.notice : Added device handler type: vrf
Fri Jun 26 19:12:27 2026 user.notice : Added device handler type: bonding
Fri Jun 26 19:12:27 2026 user.notice : Added device handler type: 8021ad
Fri Jun 26 19:12:27 2026 user.notice : Added device handler type: 8021q
Fri Jun 26 19:12:27 2026 user.notice : Added device handler type: macvlan
Fri Jun 26 19:12:27 2026 user.notice : Added device handler type: veth
Fri Jun 26 19:12:27 2026 user.notice : Added device handler type: bridge
Fri Jun 26 19:12:27 2026 user.notice : Added device handler type: Network device
Fri Jun 26 19:12:27 2026 user.notice : Added device handler type: tunnel
Fri Jun 26 19:12:27 2026 daemon.notice procd: /etc/rc.d/S25packet_steering: pid 426's current affinity list: 0-3
Fri Jun 26 19:12:27 2026 daemon.notice procd: /etc/rc.d/S25packet_steering: pid 426's new affinity list: 0
Fri Jun 26 19:12:27 2026 daemon.notice procd: /etc/rc.d/S25packet_steering: pid 427's current affinity list: 0-3
Fri Jun 26 19:12:27 2026 daemon.notice procd: /etc/rc.d/S25packet_steering: pid 427's new affinity list: 0
Fri Jun 26 19:12:27 2026 daemon.notice wpa_supplicant[1812]: Successfully initialized wpa_supplicant
Fri Jun 26 19:12:27 2026 daemon.notice hostapd: Set MLD config: [ ]
Fri Jun 26 19:12:27 2026 daemon.notice hostapd: Reload all interfaces
Fri Jun 26 19:12:27 2026 daemon.notice wpa_supplicant[1812]: Set MLD config: [ ]
Fri Jun 26 19:12:27 2026 kern.info kernel: [   14.189483] mtk_soc_eth 15100000.ethernet eth0: Link is Down
Fri Jun 26 19:12:27 2026 kern.info kernel: [   14.205425] mtk_soc_eth 15100000.ethernet eth0: configuring for fixed/2500base-x link mode
Fri Jun 26 19:12:27 2026 kern.info kernel: [   14.213883] mtk_soc_eth 15100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx
Fri Jun 26 19:12:27 2026 kern.info kernel: [   14.220932] mt7530-mdio mdio-bus:1f lan1: configuring for phy/gmii link mode
Fri Jun 26 19:12:27 2026 kern.info kernel: [   14.233822] br-lan: port 1(lan1) entered blocking state
Fri Jun 26 19:12:27 2026 kern.info kernel: [   14.239130] br-lan: port 1(lan1) entered disabled state
Fri Jun 26 19:12:27 2026 kern.info kernel: [   14.244386] mt7530-mdio mdio-bus:1f lan1: entered allmulticast mode
Fri Jun 26 19:12:27 2026 kern.info kernel: [   14.250677] mtk_soc_eth 15100000.ethernet eth0: entered allmulticast mode
Fri Jun 26 19:12:27 2026 kern.info kernel: [   14.260543] mt7530-mdio mdio-bus:1f lan1: entered promiscuous mode
Fri Jun 26 19:12:27 2026 kern.info kernel: [   14.275960] mt7530-mdio mdio-bus:1f lan2: configuring for phy/gmii link mode
Fri Jun 26 19:12:27 2026 kern.info kernel: [   14.286712] br-lan: port 2(lan2) entered blocking state
Fri Jun 26 19:12:27 2026 kern.info kernel: [   14.291955] br-lan: port 2(lan2) entered disabled state
Fri Jun 26 19:12:27 2026 kern.info kernel: [   14.297340] mt7530-mdio mdio-bus:1f lan2: entered allmulticast mode
Fri Jun 26 19:12:27 2026 kern.info kernel: [   14.305452] mt7530-mdio mdio-bus:1f lan2: entered promiscuous mode
Fri Jun 26 19:12:27 2026 kern.info kernel: [   14.319681] mt7530-mdio mdio-bus:1f lan3: configuring for phy/gmii link mode
Fri Jun 26 19:12:27 2026 kern.info kernel: [   14.330425] br-lan: port 3(lan3) entered blocking state
Fri Jun 26 19:12:27 2026 kern.info kernel: [   14.335696] br-lan: port 3(lan3) entered disabled state
Fri Jun 26 19:12:27 2026 kern.info kernel: [   14.340954] mt7530-mdio mdio-bus:1f lan3: entered allmulticast mode
Fri Jun 26 19:12:27 2026 kern.info kernel: [   14.349111] mt7530-mdio mdio-bus:1f lan3: entered promiscuous mode
Fri Jun 26 19:12:27 2026 kern.info kernel: [   14.363080] mt7530-mdio mdio-bus:1f lan4: configuring for phy/gmii link mode
Fri Jun 26 19:12:27 2026 kern.info kernel: [   14.373825] br-lan: port 4(lan4) entered blocking state
Fri Jun 26 19:12:27 2026 kern.info kernel: [   14.379080] br-lan: port 4(lan4) entered disabled state
Fri Jun 26 19:12:27 2026 kern.info kernel: [   14.384324] mt7530-mdio mdio-bus:1f lan4: entered allmulticast mode
Fri Jun 26 19:12:27 2026 kern.info kernel: [   14.392637] mt7530-mdio mdio-bus:1f lan4: entered promiscuous mode
Fri Jun 26 19:12:27 2026 daemon.notice netifd: Interface 'lan' is enabled
Fri Jun 26 19:12:27 2026 daemon.notice netifd: Interface 'lan' is setting up now
Fri Jun 26 19:12:27 2026 daemon.notice netifd: Interface 'lan' is now up
Fri Jun 26 19:12:27 2026 daemon.notice netifd: Interface 'loopback' is enabled
Fri Jun 26 19:12:27 2026 daemon.notice netifd: Interface 'loopback' is setting up now
Fri Jun 26 19:12:27 2026 daemon.notice netifd: Interface 'loopback' is now up
Fri Jun 26 19:12:27 2026 kern.info kernel: [   14.407656] mtk_soc_eth 15100000.ethernet internet: PHY [mdio-bus:06] driver [Maxlinear Ethernet GPY211C] (irq=POLL)
Fri Jun 26 19:12:27 2026 kern.info kernel: [   14.418221] mtk_soc_eth 15100000.ethernet internet: configuring for phy/2500base-x link mode
Fri Jun 26 19:12:27 2026 daemon.notice netifd: Interface 'wan' is enabled
Fri Jun 26 19:12:27 2026 daemon.notice netifd: Interface 'wan6' is enabled
Fri Jun 26 19:12:27 2026 daemon.notice netifd: Network device 'eth0' link is up
Fri Jun 26 19:12:27 2026 daemon.notice netifd: Network device 'lo' link is up
Fri Jun 26 19:12:27 2026 daemon.notice netifd: Interface 'loopback' has link connectivity
Fri Jun 26 19:12:27 2026 daemon.notice netifd: radio0 (2327): wifi-scripts: Starting
Fri Jun 26 19:12:27 2026 daemon.notice hostapd: Set new config for phy phy0:
Fri Jun 26 19:12:27 2026 daemon.notice wpa_supplicant[1812]: Set new config for phy phy0
Fri Jun 26 19:12:27 2026 user.notice firewall: Reloading firewall due to ifup of lan (br-lan)
Fri Jun 26 19:12:28 2026 daemon.notice wpa_supplicant[1812]: Set new config for phy phy0
Fri Jun 26 19:12:28 2026 daemon.notice hostapd: Set new config for phy phy0: /var/run/hostapd-phy0.conf
Fri Jun 26 19:12:28 2026 daemon.notice hostapd: Restart interface for phy phy0
Fri Jun 26 19:12:28 2026 daemon.err nlbwmon[2369]: The netlink receive buffer size of 524288 bytes will be capped to 212992 bytes
Fri Jun 26 19:12:28 2026 daemon.err nlbwmon[2369]: by the kernel. The net.core.rmem_max sysctl limit needs to be raised to
Fri Jun 26 19:12:28 2026 daemon.err nlbwmon[2369]: at least 524288 in order to sucessfully set the desired receive buffer size!
Fri Jun 26 19:12:28 2026 daemon.notice hostapd: Configuration file: <inline> (phy phy0) --> new PHY
Fri Jun 26 19:12:28 2026 daemon.notice hostapd: Configuration file: Reading configuration file '<inline>'
Fri Jun 26 19:12:28 2026 daemon.notice hostapd: Configuration file: Reading configuration file '<inline>'
Fri Jun 26 19:12:28 2026 daemon.notice netifd: radio0 (2327): wifi-scripts: Configuring 'phy0' txantenna: 4294967295, rxantenna: 4294967295 distance: 0
Fri Jun 26 19:12:28 2026 daemon.notice netifd: radio0 (2327): wifi-scripts: Preparing interface: phy0-ap0 with MAC: 06:00:dc:ea:e7:b0
Fri Jun 26 19:12:28 2026 daemon.notice netifd: radio1 (2454): wifi-scripts: Starting
Fri Jun 26 19:12:28 2026 daemon.err collectd[2502]: plugin_load: plugin "cpu" successfully loaded.
Fri Jun 26 19:12:28 2026 daemon.err collectd[2502]: plugin_load: plugin "interface" successfully loaded.
Fri Jun 26 19:12:28 2026 daemon.err collectd[2502]: plugin_load: plugin "iwinfo" successfully loaded.
Fri Jun 26 19:12:28 2026 daemon.err collectd[2502]: plugin_load: plugin "load" successfully loaded.
Fri Jun 26 19:12:28 2026 daemon.err collectd[2502]: plugin_load: plugin "memory" successfully loaded.
Fri Jun 26 19:12:28 2026 daemon.err collectd[2502]: plugin_load: plugin "rrdtool" successfully loaded.
Fri Jun 26 19:12:28 2026 daemon.err collectd[2502]: rrdtool plugin: RRASingle = true: creating only AVERAGE RRAs
Fri Jun 26 19:12:28 2026 daemon.err collectd[2502]: plugin_load: plugin "sensors" successfully loaded.
Fri Jun 26 19:12:28 2026 daemon.err collectd[2502]: Initialization complete, entering read-loop.
Fri Jun 26 19:12:28 2026 user.notice ucitrack: Setting up /etc/config/luci-splash reload dependency on /etc/config/firewall
Fri Jun 26 19:12:28 2026 user.notice ucitrack: Setting up /etc/config/qos reload dependency on /etc/config/firewall
Fri Jun 26 19:12:28 2026 user.notice ucitrack: Setting up /etc/config/miniupnpd reload dependency on /etc/config/firewall
Fri Jun 26 19:12:28 2026 user.notice ucitrack: Setting up /etc/config/odhcpd reload dependency on /etc/config/dhcp
Fri Jun 26 19:12:28 2026 user.notice ucitrack: Setting up /etc/config/dhcp reload dependency on /etc/config/network
Fri Jun 26 19:12:28 2026 user.notice ucitrack: Setting up /etc/config/network reload dependency on /etc/config/wireless
Fri Jun 26 19:12:28 2026 user.notice ucitrack: Setting up non-init /etc/config/fstab reload handler: /sbin/block mount
Fri Jun 26 19:12:28 2026 user.notice ucitrack: Setting up /etc/config/system reload trigger for non-procd /etc/init.d/led
Fri Jun 26 19:12:28 2026 user.notice ucitrack: Setting up /etc/config/luci_statistics reload dependency on /etc/config/system
Fri Jun 26 19:12:28 2026 user.notice ucitrack: Setting up /etc/config/dhcp reload dependency on /etc/config/system
Fri Jun 26 19:12:29 2026 kern.info kernel: [   15.665362] br-lan: port 5(phy0-ap0) entered blocking state
Fri Jun 26 19:12:29 2026 kern.info kernel: [   15.670946] br-lan: port 5(phy0-ap0) entered disabled state
Fri Jun 26 19:12:29 2026 kern.info kernel: [   15.676574] mt798x-wmac 18000000.wifi phy0-ap0: entered allmulticast mode
Fri Jun 26 19:12:29 2026 kern.info kernel: [   15.683530] mt798x-wmac 18000000.wifi phy0-ap0: entered promiscuous mode
Fri Jun 26 19:12:29 2026 kern.info kernel: [   15.690440] br-lan: port 5(phy0-ap0) entered blocking state
Fri Jun 26 19:12:29 2026 daemon.notice hostapd: phy0-ap0: interface state UNINITIALIZED->COUNTRY_UPDATE
Fri Jun 26 19:12:29 2026 kern.info kernel: [   15.696052] br-lan: port 5(phy0-ap0) entered forwarding state
Fri Jun 26 19:12:29 2026 kern.info kernel: [   15.703851] br-lan: port 5(phy0-ap0) entered disabled state
Fri Jun 26 19:12:29 2026 daemon.notice hostapd: Set new config for phy phy1:
Fri Jun 26 19:12:29 2026 daemon.notice wpa_supplicant[1812]: Set new config for phy phy1
Fri Jun 26 19:12:29 2026 daemon.err collectd[2502]: rrdtool plugin: rrd_update_r failed: /tmp/rrd/OpenWrt/memory/memory-slab_recl.rrd: opening '/tmp/rrd/OpenWrt/memory/memory-slab_recl.rrd': No such file or directory
Fri Jun 26 19:12:29 2026 daemon.err collectd[2502]: rrdtool plugin: rrd_update_r failed: /tmp/rrd/OpenWrt/memory/memory-used.rrd: opening '/tmp/rrd/OpenWrt/memory/memory-used.rrd': No such file or directory
Fri Jun 26 19:12:29 2026 daemon.err collectd[2502]: rrdtool plugin: rrd_update_r failed: /tmp/rrd/OpenWrt/load/load.rrd: Not enough arguments
Fri Jun 26 19:12:29 2026 daemon.info procd: - init complete -
Fri Jun 26 19:12:29 2026 kern.info kernel: [   15.936697] br-lan: port 5(phy0-ap0) entered blocking state
Fri Jun 26 19:12:29 2026 kern.info kernel: [   15.942287] br-lan: port 5(phy0-ap0) entered forwarding state
Fri Jun 26 19:12:29 2026 daemon.notice netifd: Network device 'phy0-ap0' link is up
Fri Jun 26 19:12:29 2026 daemon.notice netifd: bridge 'br-lan' link is up
Fri Jun 26 19:12:29 2026 daemon.notice netifd: Interface 'lan' has link connectivity
Fri Jun 26 19:12:29 2026 daemon.notice hostapd: phy0-ap0: interface state COUNTRY_UPDATE->ENABLED
Fri Jun 26 19:12:29 2026 daemon.notice hostapd: phy0-ap0: AP-ENABLED
Fri Jun 26 19:12:29 2026 user.notice nlbwmon: Reloading nlbwmon due to ifup of lan (br-lan)
Fri Jun 26 19:12:29 2026 daemon.notice wpa_supplicant[1812]: Set new config for phy phy1
Fri Jun 26 19:12:29 2026 daemon.notice hostapd: Set new config for phy phy1: /var/run/hostapd-phy1.conf
Fri Jun 26 19:12:29 2026 daemon.notice hostapd: Restart interface for phy phy1
Fri Jun 26 19:12:29 2026 daemon.notice hostapd: Configuration file: <inline> (phy phy1) --> new PHY
Fri Jun 26 19:12:29 2026 daemon.notice hostapd: Configuration file: Reading configuration file '<inline>'
Fri Jun 26 19:12:29 2026 daemon.notice hostapd: Configuration file: Reading configuration file '<inline>'
Fri Jun 26 19:12:29 2026 daemon.notice netifd: radio1 (2454): wifi-scripts: Configuring 'phy1' txantenna: 4294967295, rxantenna: 4294967295 distance: 0
Fri Jun 26 19:12:29 2026 daemon.notice netifd: radio1 (2454): wifi-scripts: Preparing interface: phy1-ap0 with MAC: 06:00:dc:ea:e7:b3
Fri Jun 26 19:12:29 2026 daemon.notice wpa_supplicant[1812]: Start pending MLD interfaces
Fri Jun 26 19:12:29 2026 kern.info kernel: [   16.099551] br-lan: port 6(phy1-ap0) entered blocking state
Fri Jun 26 19:12:29 2026 kern.info kernel: [   16.105128] br-lan: port 6(phy1-ap0) entered disabled state
Fri Jun 26 19:12:29 2026 kern.info kernel: [   16.110754] mt798x-wmac 18000000.wifi phy1-ap0: entered allmulticast mode
Fri Jun 26 19:12:29 2026 kern.info kernel: [   16.117761] mt798x-wmac 18000000.wifi phy1-ap0: entered promiscuous mode
Fri Jun 26 19:12:29 2026 kern.info kernel: [   16.124683] br-lan: port 6(phy1-ap0) entered blocking state
Fri Jun 26 19:12:29 2026 kern.info kernel: [   16.130297] br-lan: port 6(phy1-ap0) entered forwarding state
Fri Jun 26 19:12:29 2026 daemon.notice hostapd: phy1-ap0: interface state UNINITIALIZED->COUNTRY_UPDATE
Fri Jun 26 19:12:29 2026 daemon.notice hostapd: phy1-ap0: interface state COUNTRY_UPDATE->HT_SCAN
Fri Jun 26 19:12:29 2026 kern.info kernel: [   16.136346] br-lan: port 6(phy1-ap0) entered disabled state
Fri Jun 26 19:12:29 2026 user.notice nlbwmon: Reloading nlbwmon due to ifup of loopback (lo)
Fri Jun 26 19:12:30 2026 kern.info kernel: [   16.665093] br-lan: port 6(phy1-ap0) entered blocking state
Fri Jun 26 19:12:30 2026 kern.info kernel: [   16.670677] br-lan: port 6(phy1-ap0) entered forwarding state
Fri Jun 26 19:12:30 2026 daemon.notice netifd: Network device 'phy1-ap0' link is up
Fri Jun 26 19:12:30 2026 daemon.notice hostapd: phy1-ap0: interface state HT_SCAN->ENABLED
Fri Jun 26 19:12:30 2026 daemon.notice hostapd: phy1-ap0: AP-ENABLED
Fri Jun 26 19:12:32 2026 daemon.info dnsmasq[1]: exiting on receipt of SIGTERM
Fri Jun 26 19:12:32 2026 daemon.info dnsmasq[1]: started, version 2.93 cachesize 1000
Fri Jun 26 19:12:32 2026 daemon.info dnsmasq[1]: DNS service limited to local subnets
Fri Jun 26 19:12:32 2026 daemon.info dnsmasq[1]: compile time options: IPv6 GNU-getopt no-DBus UBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-nftset no-auth no-DNSSEC no-ID loop-detect inotify dumpfile
Fri Jun 26 19:12:32 2026 daemon.info dnsmasq[1]: UBus support enabled: connected to system bus
Fri Jun 26 19:12:32 2026 daemon.info dnsmasq-dhcp[1]: DHCP, IP range 192.168.1.100 -- 192.168.1.249, lease time 12h
Fri Jun 26 19:12:32 2026 daemon.info dnsmasq[1]: using only locally-known addresses for test
Fri Jun 26 19:12:32 2026 daemon.info dnsmasq[1]: using only locally-known addresses for onion
Fri Jun 26 19:12:32 2026 daemon.info dnsmasq[1]: using only locally-known addresses for localhost
Fri Jun 26 19:12:32 2026 daemon.info dnsmasq[1]: using only locally-known addresses for local
Fri Jun 26 19:12:32 2026 daemon.info dnsmasq[1]: using only locally-known addresses for invalid
Fri Jun 26 19:12:32 2026 daemon.info dnsmasq[1]: using only locally-known addresses for bind
Fri Jun 26 19:12:32 2026 daemon.info dnsmasq[1]: using only locally-known addresses for lan
Fri Jun 26 19:12:32 2026 daemon.warn dnsmasq[1]: no servers found in /tmp/resolv.conf.d/resolv.conf.auto, will retry
Fri Jun 26 19:12:32 2026 daemon.info dnsmasq[1]: read /etc/hosts - 12 names
Fri Jun 26 19:12:32 2026 daemon.info dnsmasq[1]: read /tmp/hosts/dhcp.cfg01411c - 4 names
Fri Jun 26 19:12:32 2026 daemon.info dnsmasq-dhcp[1]: read /etc/ethers - 0 addresses
Fri Jun 26 19:12:32 2026 user.info adblock-4.5.6-r2[2008]: adblock instance started ::: action: boot, priority: 0, pid: 2008
Fri Jun 26 19:12:32 2026 daemon.info dnsmasq[1]: read /etc/hosts - 12 names
Fri Jun 26 19:12:32 2026 daemon.info dnsmasq[1]: read /tmp/hosts/dhcp.cfg01411c - 4 names
Fri Jun 26 19:12:32 2026 daemon.info dnsmasq-dhcp[1]: read /etc/ethers - 0 addresses
Fri Jun 26 19:12:38 2026 user.info adblock-4.5.6-r2[2008]: download of 'adguard' failed, url: https://adguardteam.github.io/AdGuardSDNSFilter/Filters/filter.txt, rule: feed || 3 [|^], categories: -, rc: 4
Fri Jun 26 19:12:38 2026 user.info adblock-4.5.6-r2[2008]: download of 'certpl' failed, url: https://hole.cert.pl/domains/v2/domains.txt, rule: feed 1, categories: -, rc: 4
Fri Jun 26 19:12:38 2026 user.info adblock-4.5.6-r2[2008]: download of 'adguard_tracking' failed, url: https://raw.githubusercontent.com/AdguardTeam/cname-trackers/master/data/combined_disguised_trackers_justdomains.txt, rule: feed 1, categories: -, rc: 4
Fri Jun 26 19:12:38 2026 user.info adblock-4.5.6-r2[2008]: no merge input, only header written to /tmp/dnsmasq.cfg01411c.d/adb_list.overall
Fri Jun 26 19:12:38 2026 daemon.info dnsmasq[1]: exiting on receipt of SIGTERM
Fri Jun 26 19:12:38 2026 kern.info kernel: [   24.769549] mt7530-mdio mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control rx/tx
Fri Jun 26 19:12:38 2026 kern.info kernel: [   24.769592] br-lan: port 1(lan1) entered blocking state
Fri Jun 26 19:12:38 2026 kern.info kernel: [   24.782704] br-lan: port 1(lan1) entered forwarding state
Fri Jun 26 19:12:38 2026 daemon.notice netifd: Network device 'lan1' link is up
Fri Jun 26 19:12:38 2026 daemon.warn odhcpd[2067]: No default route present, setting ra_lifetime to 0!
Fri Jun 26 19:12:38 2026 daemon.warn odhcpd[2067]: rfc9096: br-lan: piofile updated
Fri Jun 26 19:12:38 2026 authpriv.info dropbear[4296]: Child connection from 192.168.1.220:62574
Fri Jun 26 19:12:40 2026 authpriv.notice dropbear[4296]: Auth succeeded with blank password for 'root' from 192.168.1.220:62574
Fri Jun 26 19:12:40 2026 daemon.info dnsmasq[1]: started, version 2.93 cachesize 1000
Fri Jun 26 19:12:40 2026 daemon.info dnsmasq[1]: DNS service limited to local subnets
Fri Jun 26 19:12:40 2026 daemon.info dnsmasq[1]: compile time options: IPv6 GNU-getopt no-DBus UBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-nftset no-auth no-DNSSEC no-ID loop-detect inotify dumpfile
Fri Jun 26 19:12:40 2026 daemon.info dnsmasq[1]: UBus support enabled: connected to system bus
Fri Jun 26 19:12:40 2026 daemon.info dnsmasq-dhcp[1]: DHCP, IP range 192.168.1.100 -- 192.168.1.249, lease time 12h
Fri Jun 26 19:12:40 2026 daemon.info dnsmasq[1]: using only locally-known addresses for test
Fri Jun 26 19:12:40 2026 daemon.info dnsmasq[1]: using only locally-known addresses for onion
Fri Jun 26 19:12:40 2026 daemon.info dnsmasq[1]: using only locally-known addresses for localhost
Fri Jun 26 19:12:40 2026 daemon.info dnsmasq[1]: using only locally-known addresses for local
Fri Jun 26 19:12:40 2026 daemon.info dnsmasq[1]: using only locally-known addresses for invalid
Fri Jun 26 19:12:40 2026 daemon.info dnsmasq[1]: using only locally-known addresses for bind
Fri Jun 26 19:12:40 2026 daemon.info dnsmasq[1]: using only locally-known addresses for lan
Fri Jun 26 19:12:40 2026 daemon.warn dnsmasq[1]: no servers found in /tmp/resolv.conf.d/resolv.conf.auto, will retry
Fri Jun 26 19:12:40 2026 daemon.info dnsmasq[1]: read /etc/hosts - 12 names
Fri Jun 26 19:12:40 2026 daemon.info dnsmasq[1]: read /tmp/hosts/dhcp.cfg01411c - 4 names
Fri Jun 26 19:12:40 2026 daemon.info dnsmasq[1]: read /tmp/hosts/odhcpd.hosts.lan - 2 names
Fri Jun 26 19:12:40 2026 daemon.info dnsmasq-dhcp[1]: read /etc/ethers - 0 addresses
Fri Jun 26 19:12:41 2026 daemon.info dnsmasq-dhcp[1]: DHCPREQUEST(br-lan) 192.168.1.220 00:21:cc:c0:00:00
Fri Jun 26 19:12:41 2026 daemon.info dnsmasq-dhcp[1]: DHCPACK(br-lan) 192.168.1.220 00:21:cc:c0:00:00 T420
Fri Jun 26 19:12:41 2026 user.info adblock-4.5.6-r2[2008]: blocklist with overall 0 blocked domains loaded successfully (D-Link AQUILA PRO AI M60 A1, mediatek/filogic, OpenWrt 25.12-SNAPSHOT (r33032-b830633cb8))
Fri Jun 26 19:12:42 2026 daemon.warn odhcpd[2067]: No default route present, setting ra_lifetime to 0!

kszaq · 2026-07-14 08:44:19

kszaq
Użytkownik
Nieaktywny

Zarejestrowany: 2013-06-16
Posty: 124

Odp: D-Link M30/CP (IDU dla Plusa)

W sprawie adresu MAC jest PR i dyskusja pod nim, wygląda na to, że M60 w dwupaku ma inny numer modelu na partycji ODM i potrzebny byłby parser:
https://github.com/openwrt/openwrt/pull/23902
Paser TLV pozwoliłby na pozbycie się łatki dla M30/CP, który ma ten sam "problem".

W kwestii rozszerzenia partycji, przygotuję w tym tygodniu obraz do testowania. Layout wygląda tak samo jak w M30, więc powinno pójść bez problemu tą samą drogą.

kszaq · 2026-07-15 09:11:30

kszaq
Użytkownik
Nieaktywny

Zarejestrowany: 2013-06-16
Posty: 124

Odp: D-Link M30/CP (IDU dla Plusa)

Zestaw łatek dla M30 i M60, wersja ze zmienionym układem partycji, wsparcie dla M30/CP oraz M60-2. Nie kompilowane i nie testowane, chwilowo nie mam zasobów, aby to zbudować:
https://github.com/openwrt/openwrt/comp … -cp-202607

kszaq · 2026-07-18 11:09:32

kszaq
Użytkownik
Nieaktywny

Zarejestrowany: 2013-06-16
Posty: 124

Odp: D-Link M30/CP (IDU dla Plusa)

Próbowałem zbudować, ale niestety wywala mi się cały czas na coreutils. Muszę postawić na świeżo system do budowania OpenWRT, możliwe że mam jeszcze jakieś pozostałości po budowaniu poprzednich wersji, które przeszkadzają.

Chyba że poprosimy Cezarego o zbudowanie obrazów z łatkami z mojego poprzedniego posta w miejsce dotychczasowych?

Cezary · 2026-07-18 16:01:01

Cezary
...
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2006-02-25
Posty: 116,371

Odp: D-Link M30/CP (IDU dla Plusa)

Zrob pełny patch i wystaw go gdzieś....

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

kszaq · 2026-07-18 21:22:42

kszaq
Użytkownik
Nieaktywny

Zarejestrowany: 2013-06-16
Posty: 124

Odp: D-Link M30/CP (IDU dla Plusa)

@pytonlon Proszę, oto testowe obrazy dla M60 z poszerzeniem rozmiaru partycji systemowej oraz (być może się uda) poprawką dla adresów MAC. Nie obiecuję nic w kwestii ich zawartości, budowałem z domyślnym configiem, celem jest sprawdzenie czy działa powiększenie miejsca na dane oraz czy MACi zaczutują się prawidłowo. Instaluje się przez recovery: najpierw obraz recovery, który startuje do initramfs, a następnie z poziomu tej wersji instalujemy sysupgrade:
https://drive.google.com/drive/folders/ … sp=sharing

Gdyby coś nie wchodziło, z poziomu D-Linkowego recovery można wgrać "normalny" build OpenWRT.

Powrót do normalnego układu partycji: wywołanie poniższych komend z poziomu OpenWRT i instalacja fabrycznego obrazu lub "normalnego" OpenWRT z poziomu recovery:

fw_setenv sw_tryactive 0
fw_setenv boot_by_tryactive "env default -a; saveenv; aup; reset"

pytonlon

pytonlon
Użytkownik
Nieaktywny

Skąd: KRK
Zarejestrowany: 2025-01-21
Posty: 15

Odp: D-Link M30/CP (IDU dla Plusa)

@kszaq dziękuję za link z obrazem, zabiorę się za wgrywanie po powrocie z weekendu, będę raportował postępy.

kszaq

kszaq
Użytkownik
Nieaktywny

Zarejestrowany: 2013-06-16
Posty: 124

Odp: D-Link M30/CP (IDU dla Plusa)

Dzięki, czekam na feedback. Jeszcze raz zastrzegam: nie używać "na produkcji", nie zainstalujesz żadnych kmod na tym obrazie, istotne jest wyłącznie czy działają 2 rzeczy, na które są łatki.

pytonlon

pytonlon
Użytkownik
Nieaktywny

Skąd: KRK
Zarejestrowany: 2025-01-21
Posty: 15

Odp: D-Link M30/CP (IDU dla Plusa)

raport
Przygotowane recovery i sysupgrade wykorzystane
router nie wstał do białego led-a; zgłosił partycje powiększoną; adresy mac nie zmieniły się

root@OpenWrt:~# fw_printenv
baudrate=115200
boot_by_part=if itest.s ${mupgrade_en} == 1; then aup;fi;if itest.s ${bootpart} == 0; then run set_act1; run ub0; else run set_act2; run ub1; fi
boot_by_tryactive=if itest.s ${sw_tryactive} == 0; then setenv sw_tryactive 2; setenv sw_active 1; saveenv; run ub0; else setenv sw_tryactive 2; setenv sw_active 2; saveenv; run ub1; fi
boot_rd_auto_sw_img=if itest.s ${sw_tryactive} == 2; then run boot_by_part; else run boot_by_tryactive; fi
bootargs=console=ttyS0,115200n1 loglevel=8 isolcpus=1 earlycon=uart8250,mmio32,0x11002000 bootpart=ubi0
bootdelay=2
bootmenu_0=Startup system (Default)=run boot_rd_auto_sw_img
bootmenu_1=Upgrade firmware=mtkupgrade fw
bootmenu_2=Upgrade ATF BL2=mtkupgrade bl2
bootmenu_3=Upgrade ATF FIP=mtkupgrade fip
bootmenu_4=Http Upgrade=uip main; reset
bootmenu_5=Upgrade single image=mtkupgrade simg
bootmenu_6=Load image=mtkload
bootpart=0
con=0
en_wdt=wdt on 30
ethact=ethernet@15100000
fdtcontroladdr=5ff3a000
fw_ver_a=V1.11B03
i=7
ipaddr=192.168.200.1
loadaddr=0x46000000
mtdids=nmbm0=nmbm0
mtdparts=nmbm0:1024k(bl2),512k(u-boot-env),2048k(factory),2048k(fip),102400k(ubi),256k(Odm),512k(Config1),512k(Config2),5120k(Storage)
mupgrade_en=0
netmask=255.255.255.0
power_on_rst_recov=setexpr i 8;setexpr con 1;while itest ${con} -gt 0; do  if gpio input 10; then   gpio toggle 44; else   setexpr con 0; fi; sleep 1; if itest ${i} -eq 0; then   setexpr con 0; else   setexpr i ${i} - 1; fi;done;if itest ${i} -gt 0; then  if itest ${i} -lt 4; then   setenv FW_RESET_FLAG 1; saveenv;  echo set FW_RESET_FLAG to 1;  gpio toggle 44;sleep 0.2;  gpio toggle 44;sleep 0.2;  gpio toggle 44;sleep 0.2;  gpio toggle 44;sleep 0.2;  gpio toggle 44;sleep 0.2;  gpio toggle 44; fi;else  uip main;fi
serverip=192.168.200.2
set_act1=if itest.s ${sw_active} != 1; then setenv sw_active 1; saveenv; fi
set_act2=if itest.s ${sw_active} != 2; then setenv sw_active 2; saveenv; fi
stderr=serial@11002000
stdin=serial@11002000
stdout=serial@11002000
sw_active=1
sw_tryactive=2
ub0=setenv bootpart 0; mtkboardboot; run ub0to1; uip main; reset
ub0to1=setenv bootpart 1; mtkboardboot
ub1=setenv bootpart 1; mtkboardboot; run ub1to0; uip main; reset
ub1to0=setenv bootpart 0; mtkboardboot

logread

root@OpenWrt:~# logread
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
Sat Jul 18 19:39:02 2026 kern.notice kernel: [    0.000000] Linux version 6.12.94 (mk@WSL) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 14.3.0 r33073-12815d8f0c) 14.3.0, GNU ld (GNU Binutils) 2.44) #0 SMP Sat Jul 18 19:39:01 2026
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.000000] Machine model: D-Link AQUILA PRO AI M60 A1 (OpenWrt partition layout)
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.000000] earlycon: uart8250 at MMIO32 0x0000000011002000 (options '')
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.000000] printk: legacy bootconsole [uart8250] enabled
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.000000] OF: reserved mem: 0x0000000042ff0000..0x0000000042ffffff (64 KiB) map non-reusable ramoops@42ff0000
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.000000] OF: reserved mem: 0x0000000043000000..0x000000004303ffff (256 KiB) nomap non-reusable secmon@43000000
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.000000] OF: reserved mem: 0x000000004fc00000..0x000000004fcfffff (1024 KiB) nomap non-reusable wmcpu-reserved@4fc00000
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.000000] OF: reserved mem: 0x000000004fd00000..0x000000004fd3ffff (256 KiB) nomap non-reusable wo-emi@4fd00000
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.000000] OF: reserved mem: 0x000000004fd40000..0x000000004fd7ffff (256 KiB) nomap non-reusable wo-emi@4fd40000
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.000000] OF: reserved mem: 0x000000004fd80000..0x000000004ffbffff (2304 KiB) nomap non-reusable wo-data@4fd80000
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.000000] Zone ranges:
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.000000]   DMA      [mem 0x0000000040000000-0x000000005fffffff]
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.000000]   DMA32    empty
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.000000]   Normal   empty
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.000000] Movable zone start for each node
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.000000] Early memory node ranges
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.000000]   node   0: [mem 0x0000000040000000-0x0000000042ffffff]
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.000000]   node   0: [mem 0x0000000043000000-0x000000004303ffff]
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.000000]   node   0: [mem 0x0000000043040000-0x000000004fbfffff]
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.000000]   node   0: [mem 0x000000004fc00000-0x000000004ffbffff]
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.000000]   node   0: [mem 0x000000004ffc0000-0x000000005fffffff]
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000005fffffff]
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.000000] psci: probing for conduit method from DT.
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.000000] psci: PSCIv1.1 detected in firmware.
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.000000] psci: Using standard PSCI v0.2 function IDs
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.000000] psci: MIGRATE_INFO_TYPE not supported.
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.000000] psci: SMC Calling Convention v1.2
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.000000] percpu: Embedded 20 pages/cpu s42648 r8192 d31080 u81920
Sat Jul 18 19:39:02 2026 kern.debug kernel: [    0.000000] pcpu-alloc: s42648 r8192 d31080 u81920 alloc=20*4096
Sat Jul 18 19:39:02 2026 kern.debug kernel: [    0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.000000] Detected VIPT I-cache on CPU0
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.000000] CPU features: detected: GIC system register CPU interface
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.000000] CPU features: kernel page table isolation disabled by kernel configuration
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.000000] alternatives: applying boot alternatives
Sat Jul 18 19:39:02 2026 kern.notice kernel: [    0.000000] Kernel command line: console=ttyS0,115200n1 loglevel=8 isolcpus=1 earlycon=uart8250,mmio32,0x11002000 bootpart=ubi0
Sat Jul 18 19:39:02 2026 kern.notice kernel: [    0.000000] Unknown kernel command line parameters "isolcpus=1 bootpart=ubi0", will be passed to user space.
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.000000] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes, linear)
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.000000] Inode-cache hash table entries: 32768 (order: 6, 262144 bytes, linear)
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 131072
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.000000] software IO TLB: SWIOTLB bounce buffer size adjusted to 0MB
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.000000] software IO TLB: area num 4.
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.000000] software IO TLB: SWIOTLB bounce buffer size roundup to 1MB
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.000000] software IO TLB: mapped [mem 0x000000005f4c0000-0x000000005f5c0000] (1MB)
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.000000] rcu: Hierarchical RCU implementation.
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.000000]       Tracing variant of Tasks RCU enabled.
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.000000] RCU Tasks Trace: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=4.
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.000000] GICv3: GIC: Using split EOI/Deactivate mode
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.000000] GICv3: 640 SPIs implemented
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.000000] GICv3: 0 Extended SPIs implemented
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.000000] Root IRQ handler: 0xffffffc080010080
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.000000] GICv3: GICv3 features: 16 PPIs
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.000000] GICv3: GICD_CTRL.DS=0, SCR_EL3.FIQ=0
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.000000] GICv3: CPU0: found redistributor 0 region 0:0x000000000c080000
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.000000] arch_timer: cp15 timer(s) running at 13.00MHz (phys).
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2ff89eacb, max_idle_ns: 440795202429 ns
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.000000] sched_clock: 56 bits at 13MHz, resolution 76ns, wraps every 4398046511101ns
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.008125] Calibrating delay loop (skipped), value calculated using timer frequency.. 26.00 BogoMIPS (lpj=130000)
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.018529] pid_max: default: 32768 minimum: 301
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.025116] Mount-cache hash table entries: 1024 (order: 1, 8192 bytes, linear)
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.032464] Mountpoint-cache hash table entries: 1024 (order: 1, 8192 bytes, linear)
Sat Jul 18 19:39:02 2026 kern.warn kernel: [    0.041819] cacheinfo: Unable to detect cache hierarchy for CPU 0
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.048531] rcu: Hierarchical SRCU implementation.
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.053338] rcu:  Max phase no-delay instances is 1000.
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.058714] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.067044] smp: Bringing up secondary CPUs ...
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.071858] Detected VIPT I-cache on CPU1
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.071899] GICv3: CPU1: found redistributor 1 region 0:0x000000000c0a0000
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.071926] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.072239] Detected VIPT I-cache on CPU2
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.072265] GICv3: CPU2: found redistributor 2 region 0:0x000000000c0c0000
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.072278] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.072577] Detected VIPT I-cache on CPU3
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.072599] GICv3: CPU3: found redistributor 3 region 0:0x000000000c0e0000
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.072609] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.072644] smp: Brought up 1 node, 4 CPUs
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.129178] SMP: Total of 4 processors activated.
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.133897] CPU: All CPU(s) started at EL2
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.138005] CPU features: detected: 32-bit EL0 Support
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.143163] CPU features: detected: CRC32 instructions
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.148336] alternatives: applying system-wide alternatives
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.154033] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.162543] Memory: 492284K/524288K available (9536K kernel code, 992K rwdata, 1832K rodata, 512K init, 316K bss, 29072K reserved, 0K cma-reserved)
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.178109] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.188014] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.194992] 29424 pages in range for non-PLT usage
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.194996] 520944 pages in range for PLT usage
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.200796] pinctrl core: initialized pinctrl subsystem
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.212303] NET: Registered PF_NETLINK/PF_ROUTE protocol family
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.218495] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.225601] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.233389] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.241678] thermal_sys: Registered thermal governor 'fair_share'
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.241682] thermal_sys: Registered thermal governor 'bang_bang'
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.247797] thermal_sys: Registered thermal governor 'step_wise'
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.253831] thermal_sys: Registered thermal governor 'user_space'
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.259912] ASID allocator initialised with 65536 entries
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.272154] pstore: Using crash dump compression: deflate
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.277579] pstore: Registered ramoops as persistent store backend
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.283782] ramoops: using 0x10000@0x42ff0000, ecc: 0
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.289814] /soc/interrupt-controller@c000000: Fixed dependency cycle(s) with /soc/interrupt-controller@c000000
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.311237] cryptd: max_cpu_qlen set to 1000
Sat Jul 18 19:39:02 2026 kern.notice kernel: [    0.316385] SCSI subsystem initialized
Sat Jul 18 19:39:02 2026 kern.debug kernel: [    0.320233] libata version 3.00 loaded.
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.325223] clocksource: Switched to clocksource arch_sys_counter
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.332931] NET: Registered PF_INET protocol family
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.337943] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear)
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.346237] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear)
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.354632] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.362424] TCP established hash table entries: 4096 (order: 3, 32768 bytes, linear)
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.370225] TCP bind hash table entries: 4096 (order: 5, 131072 bytes, linear)
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.377568] TCP: Hash tables configured (established 4096 bind 4096)
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.384097] MPTCP token hash table entries: 512 (order: 2, 12288 bytes, linear)
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.391518] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.398084] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.405218] NET: Registered PF_UNIX/PF_LOCAL protocol family
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.410919] PCI: CLS 0 bytes, default 64
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.415944] workingset: timestamp_bits=46 max_order=17 bucket_order=0
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.425852] squashfs: version 4.0 (2009/01/31) Phillip Lougher
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.431710] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.477085] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.488059] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.497153] printk: legacy console [ttyS0] disabled
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.522362] 11002000.serial: ttyS0 at MMIO 0x11002000 (irq = 116, base_baud = 2500000) is a ST16650V2
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.531661] printk: legacy console [ttyS0] enabled
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.541231] printk: legacy bootconsole [uart8250] disabled
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.555334] loop: module loaded
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.559955] spi-nand spi0.0: Macronix SPI NAND was found.
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.565381] spi-nand spi0.0: 128 MiB, block size: 128 KiB, page size: 2048, OOB size: 64
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.573981] Signature found at block 1023 [0x07fe0000]
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.579111] NMBM management region starts at block 960 [0x07800000]
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.586819] First info table with writecount 0 found in block 960
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.596991] Second info table with writecount 0 found in block 963
Sat Jul 18 19:39:02 2026 kern.info kernel: [    0.603156] NMBM has been successfully attached
Sat Jul 18 19:39:02 2026 kern.notice kernel: [    0.607852] 9 fixed-partitions partitions found on MTD device spi0.0
Sat Jul 18 19:39:02 2026 kern.notice kernel: [    0.614191] Creating 9 MTD partitions on "spi0.0":
Sat Jul 18 19:39:02 2026 kern.notice kernel: [    0.618975] 0x000000000000-0x000000100000 : "BL2"
Sat Jul 18 19:39:02 2026 kern.notice kernel: [    0.624554] 0x000000100000-0x000000180000 : "u-boot-env"
Sat Jul 18 19:39:02 2026 kern.notice kernel: [    0.630459] 0x000000180000-0x000000380000 : "Factory"
Sat Jul 18 19:39:02 2026 kern.notice kernel: [    0.636889] 0x000000380000-0x000000580000 : "FIP"
Sat Jul 18 19:39:02 2026 kern.notice kernel: [    0.642757] 0x000000580000-0x000006980000 : "ubi"
Sat Jul 18 19:39:02 2026 kern.notice kernel: [    0.693883] 0x000006980000-0x0000069c0000 : "Odm"
Sat Jul 18 19:39:02 2026 kern.notice kernel: [    0.699208] 0x0000069c0000-0x000006a40000 : "Config1"
Sat Jul 18 19:39:02 2026 kern.notice kernel: [    0.704744] 0x000006a40000-0x000006ac0000 : "Config2"
Sat Jul 18 19:39:02 2026 kern.notice kernel: [    0.710271] 0x000006ac0000-0x0000074c0000 : "Storage"
Sat Jul 18 19:39:02 2026 kern.info kernel: [    3.426213] Maxlinear Ethernet GPY211C mdio-bus:06: Firmware Version: 8.111 (0x886F)
Sat Jul 18 19:39:02 2026 kern.info kernel: [    3.437412] mtk_soc_eth 15100000.ethernet eth0: mediatek frame engine at 0xffffffc081900000, irq 120
Sat Jul 18 19:39:02 2026 kern.info kernel: [    3.447219] mtk_soc_eth 15100000.ethernet eth1: mediatek frame engine at 0xffffffc081900000, irq 120
Sat Jul 18 19:39:02 2026 kern.info kernel: [    3.456865] i2c_dev: i2c /dev entries driver
Sat Jul 18 19:39:02 2026 kern.info kernel: [    3.462952] mtk-wdt 1001c000.watchdog: Watchdog enabled (timeout=31 sec, nowayout=0)
Sat Jul 18 19:39:02 2026 kern.info kernel: [    3.471721] NET: Registered PF_INET6 protocol family
Sat Jul 18 19:39:02 2026 kern.info kernel: [    3.477694] Segment Routing with IPv6
Sat Jul 18 19:39:02 2026 kern.info kernel: [    3.481376] In-situ OAM (IOAM) with IPv6
Sat Jul 18 19:39:02 2026 kern.info kernel: [    3.485339] NET: Registered PF_PACKET protocol family
Sat Jul 18 19:39:02 2026 kern.info kernel: [    3.490390] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
Sat Jul 18 19:39:02 2026 kern.info kernel: [    3.503654] 8021q: 802.1Q VLAN Support v1.8
Sat Jul 18 19:39:02 2026 kern.info kernel: [    3.574030] mt7530-mdio mdio-bus:1f: configuring for fixed/2500base-x link mode
Sat Jul 18 19:39:02 2026 kern.info kernel: [    3.582746] mt7530-mdio mdio-bus:1f: Link is Up - 2.5Gbps/Full - flow control rx/tx
Sat Jul 18 19:39:02 2026 kern.info kernel: [    3.592735] mt7530-mdio mdio-bus:1f lan1 (uninitialized): PHY [mt7530-0:00] driver [MediaTek MT7531 PHY] (irq=125)
Sat Jul 18 19:39:02 2026 kern.info kernel: [    3.613953] mt7530-mdio mdio-bus:1f lan2 (uninitialized): PHY [mt7530-0:01] driver [MediaTek MT7531 PHY] (irq=126)
Sat Jul 18 19:39:02 2026 kern.info kernel: [    3.634730] mt7530-mdio mdio-bus:1f lan3 (uninitialized): PHY [mt7530-0:02] driver [MediaTek MT7531 PHY] (irq=127)
Sat Jul 18 19:39:02 2026 kern.info kernel: [    3.655514] mt7530-mdio mdio-bus:1f lan4 (uninitialized): PHY [mt7530-0:03] driver [MediaTek MT7531 PHY] (irq=128)
Sat Jul 18 19:39:02 2026 kern.info kernel: [    3.666833] mtk_soc_eth 15100000.ethernet eth0: entered promiscuous mode
Sat Jul 18 19:39:02 2026 kern.info kernel: [    3.673539] DSA: tree 0 setup
Sat Jul 18 19:39:02 2026 kern.notice kernel: [    3.677035] UBI: auto-attach mtd4
Sat Jul 18 19:39:02 2026 kern.notice kernel: [    3.680351] ubi0: default fastmap pool size: 40
Sat Jul 18 19:39:02 2026 kern.notice kernel: [    3.684865] ubi0: default fastmap WL pool size: 20
Sat Jul 18 19:39:02 2026 kern.notice kernel: [    3.689648] ubi0: attaching mtd4
Sat Jul 18 19:39:02 2026 kern.notice kernel: [    4.260377] ubi0: scanning is finished
Sat Jul 18 19:39:02 2026 kern.notice kernel: [    4.271820] ubi0: attached mtd4 (name "ubi", size 100 MiB)
Sat Jul 18 19:39:02 2026 kern.notice kernel: [    4.277313] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
Sat Jul 18 19:39:02 2026 kern.notice kernel: [    4.284168] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
Sat Jul 18 19:39:02 2026 kern.notice kernel: [    4.290938] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
Sat Jul 18 19:39:02 2026 kern.notice kernel: [    4.297882] ubi0: good PEBs: 800, bad PEBs: 0, corrupted PEBs: 0
Sat Jul 18 19:39:02 2026 kern.notice kernel: [    4.303869] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
Sat Jul 18 19:39:02 2026 kern.notice kernel: [    4.311072] ubi0: max/mean erase counter: 210/98, WL threshold: 4096, image sequence number: 2026954210
Sat Jul 18 19:39:02 2026 kern.notice kernel: [    4.320443] ubi0: available PEBs: 0, total reserved PEBs: 800, PEBs reserved for bad PEB handling: 19
Sat Jul 18 19:39:02 2026 kern.notice kernel: [    4.329644] ubi0: background thread "ubi_bgt0d" started, PID 679
Sat Jul 18 19:39:02 2026 kern.info kernel: [    4.336326] block ubiblock0_1: created from ubi0:1(rootfs)
Sat Jul 18 19:39:02 2026 kern.notice kernel: [    4.341799] ubiblock: device ubiblock0_1 (rootfs) set to be root filesystem
Sat Jul 18 19:39:02 2026 kern.info kernel: [    4.348853] clk: Disabling unused clocks
Sat Jul 18 19:39:02 2026 kern.info kernel: [    4.353002] PM: genpd: Disabling unused power domains
Sat Jul 18 19:39:02 2026 kern.info kernel: [    4.363886] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
Sat Jul 18 19:39:02 2026 kern.info kernel: [    4.371203] Freeing unused kernel memory: 512K
Sat Jul 18 19:39:02 2026 kern.info kernel: [    4.375689] Run /sbin/init as init process
Sat Jul 18 19:39:02 2026 kern.debug kernel: [    4.379770]   with arguments:
Sat Jul 18 19:39:02 2026 kern.debug kernel: [    4.382722]     /sbin/init
Sat Jul 18 19:39:02 2026 kern.debug kernel: [    4.385421]   with environment:
Sat Jul 18 19:39:02 2026 kern.debug kernel: [    4.388546]     HOME=/
Sat Jul 18 19:39:02 2026 kern.debug kernel: [    4.390891]     TERM=linux
Sat Jul 18 19:39:02 2026 kern.debug kernel: [    4.393583]     isolcpus=1
Sat Jul 18 19:39:02 2026 kern.debug kernel: [    4.396279]     bootpart=ubi0
Sat Jul 18 19:39:02 2026 user.info kernel: [    4.641904] init: Console is alive
Sat Jul 18 19:39:02 2026 user.info kernel: [    4.645443] init: - watchdog -
Sat Jul 18 19:39:02 2026 user.info kernel: [    4.797578] kmodloader: loading kernel modules from /etc/modules-boot.d/*
Sat Jul 18 19:39:02 2026 kern.warn kernel: [    4.822282] gpio_button_hotplug: loading out-of-tree module taints kernel.
Sat Jul 18 19:39:02 2026 user.info kernel: [    4.831579] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
Sat Jul 18 19:39:02 2026 user.info kernel: [    4.840253] init: - preinit -
Sat Jul 18 19:39:02 2026 kern.info kernel: [    5.098070] mtk_soc_eth 15100000.ethernet internet: renamed from eth1
Sat Jul 18 19:39:02 2026 kern.info kernel: [    5.112664] mtk_soc_eth 15100000.ethernet eth0: configuring for fixed/2500base-x link mode
Sat Jul 18 19:39:02 2026 kern.info kernel: [    5.121135] mtk_soc_eth 15100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx
Sat Jul 18 19:39:02 2026 kern.warn kernel: [    5.140503] mtdblock: MTD device 'Odm' is NAND, please consider using UBI block devices instead.
Sat Jul 18 19:39:02 2026 kern.info kernel: [    5.163501] mt7530-mdio mdio-bus:1f lan1: configuring for phy/gmii link mode
Sat Jul 18 19:39:02 2026 kern.info kernel: [    7.221881] mt7530-mdio mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control rx/tx
Sat Jul 18 19:39:02 2026 kern.notice kernel: [    8.615225] random: crng init done
Sat Jul 18 19:39:02 2026 kern.notice kernel: [    9.228247] UBIFS (ubi0:2): Mounting in unauthenticated mode
Sat Jul 18 19:39:02 2026 kern.notice kernel: [    9.233977] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" started, PID 800
Sat Jul 18 19:39:02 2026 kern.notice kernel: [    9.335157] UBIFS (ubi0:2): UBIFS: mounted UBI device 0, volume 2, name "rootfs_data"
Sat Jul 18 19:39:02 2026 kern.notice kernel: [    9.342985] UBIFS (ubi0:2): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
Sat Jul 18 19:39:02 2026 kern.notice kernel: [    9.352879] UBIFS (ubi0:2): FS size: 89137152 bytes (85 MiB, 702 LEBs), max 713 LEBs, journal size 4444160 bytes (4 MiB, 35 LEBs)
Sat Jul 18 19:39:02 2026 kern.notice kernel: [    9.364507] UBIFS (ubi0:2): reserved for root: 4210167 bytes (4111 KiB)
Sat Jul 18 19:39:02 2026 kern.notice kernel: [    9.371105] UBIFS (ubi0:2): media format: w5/r0 (latest is w5/r0), UUID C3839F32-9B97-49F8-A90F-36B13D33FE20, small LPT model
Sat Jul 18 19:39:02 2026 user.info kernel: [    9.383467] mount_root: overlay filesystem has not been fully initialized yet
Sat Jul 18 19:39:02 2026 user.info kernel: [    9.391543] mount_root: switching to ubifs overlay
Sat Jul 18 19:39:02 2026 kern.warn kernel: [    9.399758] overlayfs: null uuid detected in lower fs '/', falling back to xino=off,index=off,nfs_export=off.
Sat Jul 18 19:39:02 2026 user.debug kernel: [    9.520614] urandom-seed: Seed file not found (/etc/urandom.seed)
Sat Jul 18 19:39:02 2026 kern.info kernel: [   10.058339] mt7530-mdio mdio-bus:1f lan1: Link is Down
Sat Jul 18 19:39:02 2026 user.info kernel: [   10.066650] procd: - early -
Sat Jul 18 19:39:02 2026 user.info kernel: [   10.069580] procd: - watchdog -
Sat Jul 18 19:39:02 2026 user.info kernel: [   10.615328] procd: - watchdog -
Sat Jul 18 19:39:02 2026 user.info kernel: [   10.618611] procd: - ubus -
Sat Jul 18 19:39:02 2026 user.info kernel: [   10.679744] procd: - init -
Sat Jul 18 19:39:02 2026 user.info kernel: [   10.900156] kmodloader: loading kernel modules from /etc/modules.d/*
Sat Jul 18 19:39:02 2026 kern.info kernel: [   10.950852] PPP generic driver version 2.4.2
Sat Jul 18 19:39:02 2026 kern.info kernel: [   10.955858] NET: Registered PF_PPPOX protocol family
Sat Jul 18 19:39:02 2026 user.info kernel: [   10.962851] kmodloader: done loading kernel modules from /etc/modules.d/*
Sat Jul 18 19:39:02 2026 user.info kernel: [   11.053165] urngd: v1.0.2 started.
Sat Jul 18 19:39:02 2026 user.notice dnsmasq: DNS rebinding protection is active, will discard upstream RFC1918 responses!
Sat Jul 18 19:39:02 2026 user.notice dnsmasq: Allowing 127.0.0.0/8 responses
Sat Jul 18 19:39:03 2026 daemon.info dnsmasq[1]: started, version 2.93 cachesize 1000
Sat Jul 18 19:39:03 2026 daemon.info dnsmasq[1]: DNS service limited to local subnets
Sat Jul 18 19:39:03 2026 daemon.info dnsmasq[1]: compile time options: IPv6 GNU-getopt no-DBus UBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-nftset no-auth no-DNSSEC no-ID loop-detect inotify dumpfile
Sat Jul 18 19:39:03 2026 daemon.info dnsmasq[1]: UBus support enabled: connected to system bus
Sat Jul 18 19:39:03 2026 daemon.info dnsmasq[1]: using only locally-known addresses for test
Sat Jul 18 19:39:03 2026 daemon.info dnsmasq[1]: using only locally-known addresses for onion
Sat Jul 18 19:39:03 2026 daemon.info dnsmasq[1]: using only locally-known addresses for localhost
Sat Jul 18 19:39:03 2026 daemon.info dnsmasq[1]: using only locally-known addresses for local
Sat Jul 18 19:39:03 2026 daemon.info dnsmasq[1]: using only locally-known addresses for invalid
Sat Jul 18 19:39:03 2026 daemon.info dnsmasq[1]: using only locally-known addresses for bind
Sat Jul 18 19:39:03 2026 daemon.info dnsmasq[1]: using only locally-known addresses for lan
Sat Jul 18 19:39:03 2026 daemon.warn dnsmasq[1]: no servers found in /tmp/resolv.conf.d/resolv.conf.auto, will retry
Sat Jul 18 19:39:03 2026 daemon.info dnsmasq[1]: read /etc/hosts - 12 names
Sat Jul 18 19:39:03 2026 daemon.info dnsmasq[1]: read /tmp/hosts/dhcp.cfg01411c - 0 names
Sat Jul 18 19:39:03 2026 authpriv.info dropbear[1612]: Not backgrounding
Sat Jul 18 19:39:03 2026 user.notice : Added device handler type: vrf
Sat Jul 18 19:39:03 2026 user.notice : Added device handler type: bonding
Sat Jul 18 19:39:03 2026 user.notice : Added device handler type: 8021ad
Sat Jul 18 19:39:03 2026 user.notice : Added device handler type: 8021q
Sat Jul 18 19:39:03 2026 user.notice : Added device handler type: macvlan
Sat Jul 18 19:39:03 2026 user.notice : Added device handler type: veth
Sat Jul 18 19:39:03 2026 user.notice : Added device handler type: bridge
Sat Jul 18 19:39:03 2026 user.notice : Added device handler type: Network device
Sat Jul 18 19:39:03 2026 user.notice : Added device handler type: tunnel
Sat Jul 18 19:39:03 2026 daemon.notice procd: /etc/rc.d/S25packet_steering: pid 421's current affinity list: 0-3
Sat Jul 18 19:39:03 2026 daemon.notice procd: /etc/rc.d/S25packet_steering: pid 421's new affinity list: 0
Sat Jul 18 19:39:03 2026 daemon.notice procd: /etc/rc.d/S25packet_steering: pid 422's current affinity list: 0-3
Sat Jul 18 19:39:03 2026 daemon.notice procd: /etc/rc.d/S25packet_steering: pid 422's new affinity list: 0
Sat Jul 18 19:39:04 2026 daemon.warn netifd: Wireless module not found
Sat Jul 18 19:39:04 2026 daemon.err wpa_supplicant[1778]: Error loading ucode: Syntax error: Unable to resolve path for module 'common' In line 4, byte 116:   `import { wdev_create, wdev_set_mesh_params, wdev_remove, is_equal, wdev_set_up, vlist_new, phy_open } from "common";`   Near here ---------------------------------------------------------------------------------------------------------^
Sat Jul 18 19:39:04 2026 daemon.notice wpa_supplicant[1778]: Successfully initialized wpa_supplicant
Sat Jul 18 19:39:04 2026 daemon.err hostapd: Error loading ucode: Syntax error: Unable to resolve path for module 'common' In line 3, byte 118:   `import { wdev_remove, is_equal, vlist_new, phy_is_fullmac, phy_open, wdev_set_radio_mask, wdev_set_up } from "common";`   Near here -----------------------------------------------------------------------------------------------------------^
Sat Jul 18 19:39:04 2026 kern.info kernel: [   12.890585] mtk_soc_eth 15100000.ethernet eth0: Link is Down
Sat Jul 18 19:39:04 2026 kern.info kernel: [   12.905511] mtk_soc_eth 15100000.ethernet eth0: configuring for fixed/2500base-x link mode
Sat Jul 18 19:39:04 2026 kern.info kernel: [   12.915344] mtk_soc_eth 15100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx
Sat Jul 18 19:39:04 2026 kern.info kernel: [   12.920744] mt7530-mdio mdio-bus:1f lan1: configuring for phy/gmii link mode
Sat Jul 18 19:39:04 2026 kern.info kernel: [   12.937392] br-lan: port 1(lan1) entered blocking state
Sat Jul 18 19:39:04 2026 kern.info kernel: [   12.942638] br-lan: port 1(lan1) entered disabled state
Sat Jul 18 19:39:04 2026 kern.info kernel: [   12.947947] mt7530-mdio mdio-bus:1f lan1: entered allmulticast mode
Sat Jul 18 19:39:04 2026 kern.info kernel: [   12.954214] mtk_soc_eth 15100000.ethernet eth0: entered allmulticast mode
Sat Jul 18 19:39:04 2026 kern.info kernel: [   12.963943] mt7530-mdio mdio-bus:1f lan1: entered promiscuous mode
Sat Jul 18 19:39:04 2026 daemon.notice netifd: Interface 'lan' is enabled
Sat Jul 18 19:39:04 2026 daemon.notice netifd: Interface 'lan' is setting up now
Sat Jul 18 19:39:04 2026 daemon.notice netifd: Interface 'lan' is now up
Sat Jul 18 19:39:04 2026 kern.info kernel: [   12.983509] mt7530-mdio mdio-bus:1f lan2: configuring for phy/gmii link mode
Sat Jul 18 19:39:04 2026 kern.info kernel: [   12.994528] br-lan: port 2(lan2) entered blocking state
Sat Jul 18 19:39:04 2026 kern.info kernel: [   12.999824] br-lan: port 2(lan2) entered disabled state
Sat Jul 18 19:39:04 2026 kern.info kernel: [   13.005082] mt7530-mdio mdio-bus:1f lan2: entered allmulticast mode
Sat Jul 18 19:39:04 2026 kern.info kernel: [   13.013344] mt7530-mdio mdio-bus:1f lan2: entered promiscuous mode
Sat Jul 18 19:39:04 2026 kern.info kernel: [   13.028883] mt7530-mdio mdio-bus:1f lan3: configuring for phy/gmii link mode
Sat Jul 18 19:39:04 2026 kern.info kernel: [   13.039617] br-lan: port 3(lan3) entered blocking state
Sat Jul 18 19:39:04 2026 kern.info kernel: [   13.044853] br-lan: port 3(lan3) entered disabled state
Sat Jul 18 19:39:04 2026 kern.info kernel: [   13.050153] mt7530-mdio mdio-bus:1f lan3: entered allmulticast mode
Sat Jul 18 19:39:04 2026 user.notice firewall: Reloading firewall due to ifup of lan (br-lan)
Sat Jul 18 19:39:04 2026 kern.info kernel: [   13.058294] mt7530-mdio mdio-bus:1f lan3: entered promiscuous mode
Sat Jul 18 19:39:04 2026 kern.info kernel: [   13.073228] mt7530-mdio mdio-bus:1f lan4: configuring for phy/gmii link mode
Sat Jul 18 19:39:04 2026 kern.info kernel: [   13.083965] br-lan: port 4(lan4) entered blocking state
Sat Jul 18 19:39:04 2026 kern.info kernel: [   13.089222] br-lan: port 4(lan4) entered disabled state
Sat Jul 18 19:39:04 2026 kern.info kernel: [   13.094472] mt7530-mdio mdio-bus:1f lan4: entered allmulticast mode
Sat Jul 18 19:39:04 2026 kern.info kernel: [   13.102798] mt7530-mdio mdio-bus:1f lan4: entered promiscuous mode
Sat Jul 18 19:39:04 2026 daemon.notice netifd: Interface 'loopback' is enabled
Sat Jul 18 19:39:04 2026 daemon.notice netifd: Interface 'loopback' is setting up now
Sat Jul 18 19:39:04 2026 daemon.notice netifd: Interface 'loopback' is now up
Sat Jul 18 19:39:04 2026 kern.info kernel: [   13.112862] mtk_soc_eth 15100000.ethernet internet: PHY [mdio-bus:06] driver [Maxlinear Ethernet GPY211C] (irq=POLL)
Sat Jul 18 19:39:04 2026 kern.info kernel: [   13.123396] mtk_soc_eth 15100000.ethernet internet: configuring for phy/2500base-x link mode
Sat Jul 18 19:39:04 2026 daemon.notice netifd: Interface 'wan' is enabled
Sat Jul 18 19:39:04 2026 daemon.notice netifd: Interface 'wan6' is enabled
Sat Jul 18 19:39:04 2026 daemon.notice netifd: Network device 'eth0' link is up
Sat Jul 18 19:39:04 2026 daemon.notice netifd: Network device 'lo' link is up
Sat Jul 18 19:39:04 2026 daemon.notice netifd: Interface 'loopback' has link connectivity
Sat Jul 18 19:39:04 2026 daemon.info procd: - init complete -
Sat Jul 18 19:39:04 2026 daemon.info urandom_seed[2279]: Seed saved (/etc/urandom.seed)
Sat Jul 18 19:39:07 2026 kern.info kernel: [   16.290809] mt7530-mdio mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control rx/tx
Sat Jul 18 19:39:07 2026 kern.info kernel: [   16.290832] br-lan: port 1(lan1) entered blocking state
Sat Jul 18 19:39:07 2026 kern.info kernel: [   16.303937] br-lan: port 1(lan1) entered forwarding state
Sat Jul 18 19:39:07 2026 daemon.notice netifd: Network device 'lan1' link is up
Sat Jul 18 19:39:07 2026 daemon.notice netifd: bridge 'br-lan' link is up
Sat Jul 18 19:39:07 2026 daemon.notice netifd: Interface 'lan' has link connectivity
Sat Jul 18 19:39:08 2026 daemon.err odhcpd[1903]: Failed to send to fe80::c4ba:e0c2:5d00:c0ec%lan@br-lan (Address not available)
Sat Jul 18 19:39:08 2026 daemon.info dnsmasq[1]: exiting on receipt of SIGTERM
Sat Jul 18 19:39:08 2026 daemon.err procd: Got unexpected signal 1
Sat Jul 18 19:39:08 2026 daemon.err odhcpd[1903]: Failed to send to fe80::c4ba:e0c2:5d00:c0ec%lan@br-lan (Address not available)
Sat Jul 18 19:39:08 2026 daemon.info dnsmasq[1]: started, version 2.93 cachesize 1000
Sat Jul 18 19:39:08 2026 daemon.info dnsmasq[1]: DNS service limited to local subnets
Sat Jul 18 19:39:08 2026 daemon.info dnsmasq[1]: compile time options: IPv6 GNU-getopt no-DBus UBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-nftset no-auth no-DNSSEC no-ID loop-detect inotify dumpfile
Sat Jul 18 19:39:08 2026 daemon.info dnsmasq[1]: UBus support enabled: connected to system bus
Sat Jul 18 19:39:08 2026 daemon.info dnsmasq-dhcp[1]: DHCP, IP range 192.168.1.100 -- 192.168.1.249, lease time 12h
Sat Jul 18 19:39:08 2026 daemon.info dnsmasq[1]: using only locally-known addresses for test
Sat Jul 18 19:39:08 2026 daemon.info dnsmasq[1]: using only locally-known addresses for onion
Sat Jul 18 19:39:08 2026 daemon.info dnsmasq[1]: using only locally-known addresses for localhost
Sat Jul 18 19:39:08 2026 daemon.info dnsmasq[1]: using only locally-known addresses for local
Sat Jul 18 19:39:08 2026 daemon.info dnsmasq[1]: using only locally-known addresses for invalid
Sat Jul 18 19:39:08 2026 daemon.info dnsmasq[1]: using only locally-known addresses for bind
Sat Jul 18 19:39:08 2026 daemon.info dnsmasq[1]: using only locally-known addresses for lan
Sat Jul 18 19:39:08 2026 daemon.warn dnsmasq[1]: no servers found in /tmp/resolv.conf.d/resolv.conf.auto, will retry
Sat Jul 18 19:39:08 2026 daemon.info dnsmasq[1]: read /etc/hosts - 12 names
Sat Jul 18 19:39:08 2026 daemon.info dnsmasq[1]: read /tmp/hosts/dhcp.cfg01411c - 4 names
Sat Jul 18 19:39:08 2026 daemon.info dnsmasq[1]: read /tmp/hosts/odhcpd.hosts.lan - 0 names
Sat Jul 18 19:39:08 2026 daemon.info dnsmasq-dhcp[1]: read /etc/ethers - 0 addresses
Sat Jul 18 19:39:08 2026 daemon.info dnsmasq[1]: read /etc/hosts - 12 names
Sat Jul 18 19:39:08 2026 daemon.info dnsmasq[1]: read /tmp/hosts/dhcp.cfg01411c - 4 names
Sat Jul 18 19:39:08 2026 daemon.info dnsmasq[1]: read /tmp/hosts/odhcpd.hosts.lan - 0 names
Sat Jul 18 19:39:08 2026 daemon.info dnsmasq-dhcp[1]: read /etc/ethers - 0 addresses
Sat Jul 18 19:39:08 2026 daemon.info dnsmasq[1]: read /etc/hosts - 12 names
Sat Jul 18 19:39:08 2026 daemon.info dnsmasq[1]: read /tmp/hosts/dhcp.cfg01411c - 4 names
Sat Jul 18 19:39:08 2026 daemon.info dnsmasq[1]: read /tmp/hosts/odhcpd.hosts.lan - 0 names
Sat Jul 18 19:39:08 2026 daemon.info dnsmasq-dhcp[1]: read /etc/ethers - 0 addresses
Sat Jul 18 19:39:09 2026 daemon.info dnsmasq[1]: read /etc/hosts - 12 names
Sat Jul 18 19:39:09 2026 daemon.info dnsmasq[1]: read /tmp/hosts/dhcp.cfg01411c - 4 names
Sat Jul 18 19:39:09 2026 daemon.info dnsmasq[1]: read /tmp/hosts/odhcpd.hosts.lan - 2 names
Sat Jul 18 19:39:09 2026 daemon.info dnsmasq-dhcp[1]: read /etc/ethers - 0 addresses
Sat Jul 18 19:39:10 2026 daemon.info dnsmasq-dhcp[1]: DHCPREQUEST(br-lan) 192.168.1.220 00:21:cc:c0:a2:00
Sat Jul 18 19:39:10 2026 daemon.info dnsmasq-dhcp[1]: DHCPACK(br-lan) 192.168.1.220 00:21:cc:c0:a2:00 T420
Sat Jul 18 19:39:11 2026 daemon.warn odhcpd[1903]: No default route present, setting ra_lifetime to 0!
Sat Jul 18 19:39:11 2026 daemon.warn odhcpd[1903]: rfc9096: br-lan: piofile updated
Sat Jul 18 19:39:15 2026 daemon.warn odhcpd[1903]: No default route present, setting ra_lifetime to 0!
Sat Jul 18 19:39:24 2026 daemon.warn odhcpd[1903]: No default route present, setting ra_lifetime to 0!

ip link zgłosił te same adresy jak poprzednio;

recovery do poprzedniego układu partycji wymagało kilka prób wgrania recovery zanim system zgłosił się poprawnie, aby wykonać komendy do przywrócenia układu partycji i wgrania "normalnego" obrazu Openwrt od Cezarego. Co zaobserwowane to inaczej troszkę wygląda zestaw raportowanych danych za pomocą fw_printenv

fw_printenv
baudrate=115200
boot_by_part=if itest.s ${mupgrade_en} == 1; then aup;fi;if itest.s ${bootpart} == 0; then run set_act1; run ub0; else run set_act2; run ub1; fi
boot_by_tryactive=if itest.s ${sw_tryactive} == 0; then setenv sw_tryactive 2; setenv sw_active 1; saveenv; run ub0; else setenv sw_tryactive 2; setenv sw_active 2; saveenv; run ub1; fi
boot_rd_auto_sw_img=if itest.s ${sw_tryactive} == 2; then run boot_by_part; else run boot_by_tryactive; fi
bootargs=console=ttyS0,115200n1 loglevel=8 isolcpus=1 earlycon=uart8250,mmio32,0x11002000 bootpart=ubi0
bootdelay=2
bootpart=0
en_wdt=wdt on 30
ipaddr=192.168.200.1
loadaddr=0x46000000
mupgrade_en=1
netmask=255.255.255.0
power_on_rst_recov=setexpr i 8;setexpr con 1;while itest ${con} -gt 0; do  if gpio input 10; then   gpio toggle 44; else   setexpr con 0; fi; sleep 1; if itest ${i} -eq 0; then   setexpr con 0; else   setexpr i ${i} - 1; fi;done;if itest ${i} -gt 0; then  if itest ${i} -lt 4; then   setenv FW_RESET_FLAG 1; saveenv;  echo set FW_RESET_FLAG to 1;  gpio toggle 44;sleep 0.2;  gpio toggle 44;sleep 0.2;  gpio toggle 44;sleep 0.2;  gpio toggle 44;sleep 0.2;  gpio toggle 44;sleep 0.2;  gpio toggle 44; fi;else  uip main;fi
serverip=192.168.200.2
set_act1=if itest.s ${sw_active} != 1; then setenv sw_active 1; saveenv; fi
set_act2=if itest.s ${sw_active} != 2; then setenv sw_active 2; saveenv; fi
sw_active=1
sw_tryactive=2
ub0=setenv bootpart 0; mtkboardboot; run ub0to1; uip main; reset
ub0to1=setenv bootpart 1; mtkboardboot
ub1=setenv bootpart 1; mtkboardboot; run ub1to0; uip main; reset
ub1to0=setenv bootpart 0; mtkboardboot

emwu88

emwu88
Użytkownik
Nieaktywny

Zarejestrowany: 2024-01-07
Posty: 9

Odp: D-Link M30/CP (IDU dla Plusa)

Witam,
i mnie spotkał ten sam problem z adresami MAC, M60 z 'dwupaku' prosto z pudełka wgrane openwrt przez recovery zakończone sukcesem.
Dziś podmiana sprzętów i jakie zdziwienie gdy w konfiguracji MF286D -> 2x M60 jako dumpAP działa tylko z jedną sztuką.
Spotkało mnie dublowanie adresów MAC na lan i wlan...
Aktualnie pozmieniane ręcznie na interfejsach.
Czy istnieje może jakiś patch który na istniejącym już systemie przywróci adresy do normalności?

# hexdump -v -n 6 -s 0x83 -e '5/1 "%02x:" 1/1 "%02x"' /dev/mtd6
powyższy odczyt działa u mnie zgodnie z naklejką na obudowie

Pozdrawiam

pytonlon napisał/a:

mac address

M60 dwupack

Box nr 1
odczytany mac za pomocą hexdump -v -n 6 -s 0x83 -e '5/1 "%02x:" 1/1 "%02x"' /dev/mtd6 daje dc:ea:e7:ae:ba:40;
etykieta dc:ea:e7:ae:ba:41
czyli zgodnie z informacjami z Commit b3ce08e
WAN dc:ea:e7:ae:ba:40
LAN dc:ea:e7:ae:ba:41
WLAN MAC(2.4) dc:ea:e7:ae:ba:42
WLAN MAC (5.0) dc:ea:e7:ae:ba:45

a system zwraca jak poniżej patrz output ip link

Box nr 2
odczytany mac za pomocą hexdump -v -n 6 -s 0x83 -e '5/1 "%02x:" 1/1 "%02x"' /dev/mtd6 daje dc:ea:e7:ae:ba:36;
etykieta dc:ea:e7:ae:ba:37
czyli zgodnie z informacjami z Commit b3ce08e
WAN dc:ea:e7:ae:ba:36
LAN dc:ea:e7:ae:ba:37
WLAN MAC(2.4) dc:ea:e7:ae:ba:38
WLAN MAC (5.0) dc:ea:e7:ae:ba:3b

a system też zwraca jak poniżej patrz output ip link

 
root@OpenWrt:~# ip link
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default qlen 1000
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1504 qdisc mq state UP mode DEFAULT group default qlen 1000
    link/ether 06:00:dc:ea:e7:af brd ff:ff:ff:ff:ff:ff
3: internet: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN mode DEFAULT group default qlen 1000
    link/ether 06:00:dc:ea:e7:ae brd ff:ff:ff:ff:ff:ff
4: lan1@eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue master br-lan state UP mode DEFAULT group default qlen 1000
    link/ether 06:00:dc:ea:e7:af brd ff:ff:ff:ff:ff:ff
5: lan2@eth0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc noqueue master br-lan state LOWERLAYERDOWN mode DEFAULT group default qlen 1000
    link/ether 06:00:dc:ea:e7:af brd ff:ff:ff:ff:ff:ff
6: lan3@eth0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc noqueue master br-lan state LOWERLAYERDOWN mode DEFAULT group default qlen 1000
    link/ether 06:00:dc:ea:e7:af brd ff:ff:ff:ff:ff:ff
7: lan4@eth0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc noqueue master br-lan state LOWERLAYERDOWN mode DEFAULT group default qlen 1000
    link/ether 06:00:dc:ea:e7:af brd ff:ff:ff:ff:ff:ff
8: br-lan: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP mode DEFAULT group default qlen 1000
    link/ether 06:00:dc:ea:e7:af brd ff:ff:ff:ff:ff:ff
9: phy0-ap0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue master br-lan state UP mode DEFAULT group default qlen 1000
    link/ether 06:00:dc:ea:e7:b0 brd ff:ff:ff:ff:ff:ff
10: phy1-ap0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue master br-lan state UP mode DEFAULT group default qlen 1000
    link/ether 06:00:dc:ea:e7:b3 brd ff:ff:ff:ff:ff:ff

wiec oba boxy są tak samo identyfikowane w sieci

kszaq

kszaq
Użytkownik
Nieaktywny

Zarejestrowany: 2013-06-16
Posty: 124

Odp: D-Link M30/CP (IDU dla Plusa)

Dzięki za testy.

Rzuciłem jeszcze okiem na PR z GitHuba, gdzie jest opisany problem z MACami na M60-2 i poprawiłem offsety. Kolejne testowe buildy w tym samym folderze na GDrive, na tych samych zasadach co poprzednio, można zrobić sysupgrade z poprzedniego builda (ale nie bezpośrednio z wersji nie-ubootmod):
https://drive.google.com/drive/folders/ … sp=sharing

FAQ o OpenWrt | Sprzedam różne routery | Oddam

D-Link M30/CP (IDU dla Plusa) (Strona 3 z 3)

Posty: 51 do 63 z 63

51 Odpowiedź przez kszaq 2026-07-13 19:46:12

Odp: D-Link M30/CP (IDU dla Plusa)

52 Odpowiedź przez pytonlon 2026-07-13 22:41:09 (edytowany przez pytonlon 2026-07-13 22:46:50)

Odp: D-Link M30/CP (IDU dla Plusa)

53 Odpowiedź przez pytonlon 2026-07-13 22:44:42

Odp: D-Link M30/CP (IDU dla Plusa)

54 Odpowiedź przez kszaq 2026-07-14 08:44:19

Odp: D-Link M30/CP (IDU dla Plusa)

55 Odpowiedź przez kszaq 2026-07-15 09:11:30

Odp: D-Link M30/CP (IDU dla Plusa)

56 Odpowiedź przez kszaq 2026-07-18 11:09:32

Odp: D-Link M30/CP (IDU dla Plusa)

57 Odpowiedź przez Cezary 2026-07-18 16:01:01

Odp: D-Link M30/CP (IDU dla Plusa)

58 Odpowiedź przez kszaq 2026-07-18 21:22:42

Odp: D-Link M30/CP (IDU dla Plusa)

59 Odpowiedź przez pytonlon Wczoraj 00:50:28

Odp: D-Link M30/CP (IDU dla Plusa)

60 Odpowiedź przez kszaq Wczoraj 11:19:11

Odp: D-Link M30/CP (IDU dla Plusa)

61 Odpowiedź przez pytonlon Dzisiaj 00:14:54

Odp: D-Link M30/CP (IDU dla Plusa)

62 Odpowiedź przez emwu88 Dzisiaj 17:57:23

Odp: D-Link M30/CP (IDU dla Plusa)

63 Odpowiedź przez kszaq Dzisiaj 20:21:03

Odp: D-Link M30/CP (IDU dla Plusa)

Posty: 51 do 63 z 63