Odp: Cudy P2 5G v1.0 - wsparcie OpenWRT
Udało mi się skompilować ten sterownik, zrobiłem obraz z nim, ale po sysupgrade mam kernel panic i router się rebootuje w kółko. Ma to chyba związek z tymi błędami AER.
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[ 0.000000] Linux version 6.12.85 (lukasz@lukasz-mint) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 14.3.0 r32924-e850a972b5) 14.3.0, GNU ld (GNU Binutils) 2.44) #0 SMP Sat May 9 09:05:32 2026
[ 0.000000] Machine model: Cudy P2 5G
[ 0.000000] OF: reserved mem: 0x0000000042ff0000..0x0000000042ffffff (64 KiB) map non-reusable ramoops@42ff0000
[ 0.000000] OF: reserved mem: 0x0000000043000000..0x000000004302ffff (192 KiB) nomap non-reusable secmon@43000000
[ 0.000000] OF: reserved mem: 0x0000000047c80000..0x0000000047d7ffff (1024 KiB) nomap non-reusable wmcpu-reserved@47c80000
[ 0.000000] OF: reserved mem: 0x0000000047d80000..0x0000000047dbffff (256 KiB) nomap non-reusable wo-emi@47d80000
[ 0.000000] OF: reserved mem: 0x0000000047dc0000..0x0000000047ffffff (2304 KiB) nomap non-reusable wo-data@47dc0000
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000040000000-0x000000004fffffff]
[ 0.000000] DMA32 empty
[ 0.000000] Normal empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000040000000-0x0000000042ffffff]
[ 0.000000] node 0: [mem 0x0000000043000000-0x000000004302ffff]
[ 0.000000] node 0: [mem 0x0000000043030000-0x0000000047c7ffff]
[ 0.000000] node 0: [mem 0x0000000047c80000-0x0000000047ffffff]
[ 0.000000] node 0: [mem 0x0000000048000000-0x000000004fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000004fffffff]
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.1 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] psci: SMC Calling Convention v1.2
[ 0.000000] percpu: Embedded 20 pages/cpu s42520 r8192 d31208 u81920
[ 0.000000] pcpu-alloc: s42520 r8192 d31208 u81920 alloc=20*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] CPU features: detected: GIC system register CPU interface
[ 0.000000] CPU features: kernel page table isolation disabled by kernel configuration
[ 0.000000] alternatives: applying boot alternatives
[ 0.000000] Kernel command line:
[ 0.000000] Dentry cache hash table entries: 32768 (order: 6, 262144 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 65536
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] software IO TLB: SWIOTLB bounce buffer size adjusted to 0MB
[ 0.000000] software IO TLB: area num 2.
[ 0.000000] software IO TLB: SWIOTLB bounce buffer size roundup to 0MB
[ 0.000000] software IO TLB: mapped [mem 0x000000004fe49000-0x000000004fec9000] (0MB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] RCU Tasks Trace: Setting shift to 1 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=2.
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode
[ 0.000000] GICv3: 640 SPIs implemented
[ 0.000000] GICv3: 0 Extended SPIs implemented
[ 0.000000] Root IRQ handler: gic_handle_irq
[ 0.000000] GICv3: GICv3 features: 16 PPIs
[ 0.000000] GICv3: GICD_CTRL.DS=0, SCR_EL3.FIQ=0
[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x000000000c080000
[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[ 0.000000] arch_timer: cp15 timer(s) running at 13.00MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2ff89eacb, max_idle_ns: 440795202429 ns
[ 0.000000] sched_clock: 56 bits at 13MHz, resolution 76ns, wraps every 4398046511101ns
[ 0.000081] Calibrating delay loop (skipped), value calculated using timer frequency.. 26.00 BogoMIPS (lpj=130000)
[ 0.000089] pid_max: default: 32768 minimum: 301
[ 0.003069] Mount-cache hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 0.003077] Mountpoint-cache hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 0.005191] cacheinfo: Unable to detect cache hierarchy for CPU 0
[ 0.005998] rcu: Hierarchical SRCU implementation.
[ 0.006004] rcu: Max phase no-delay instances is 1000.
[ 0.006196] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level
[ 0.006424] smp: Bringing up secondary CPUs ...
[ 0.006774] Detected VIPT I-cache on CPU1
[ 0.006818] GICv3: CPU1: found redistributor 1 region 0:0x000000000c0a0000
[ 0.006846] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[ 0.006927] smp: Brought up 1 node, 2 CPUs
[ 0.006932] SMP: Total of 2 processors activated.
[ 0.006935] CPU: All CPU(s) started at EL2
[ 0.006937] CPU features: detected: 32-bit EL0 Support
[ 0.006940] CPU features: detected: CRC32 instructions
[ 0.006967] alternatives: applying system-wide alternatives
[ 0.007097] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching
[ 0.007225] Memory: 236832K/262144K available (9280K kernel code, 984K rwdata, 2764K rodata, 448K init, 300K bss, 23668K reserved, 0K cma-reserved)
[ 0.010345] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.010363] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
[ 0.010420] 29280 pages in range for non-PLT usage
[ 0.010423] 520800 pages in range for PLT usage
[ 0.011919] pinctrl core: initialized pinctrl subsystem
[ 0.013089] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.013387] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations
[ 0.013412] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[ 0.013432] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[ 0.013824] thermal_sys: Registered thermal governor 'fair_share'
[ 0.013828] thermal_sys: Registered thermal governor 'bang_bang'
[ 0.013831] thermal_sys: Registered thermal governor 'step_wise'
[ 0.013834] thermal_sys: Registered thermal governor 'user_space'
[ 0.013882] ASID allocator initialised with 65536 entries
[ 0.014587] pstore: Using crash dump compression: deflate
[ 0.014592] pstore: Registered ramoops as persistent store backend
[ 0.014595] ramoops: using 0x10000@0x42ff0000, ecc: 0
[ 0.016257] /soc/interrupt-controller@c000000: Fixed dependency cycle(s) with /soc/interrupt-controller@c000000
[ 0.017511] /soc/pcie@11280000: Fixed dependency cycle(s) with /soc/pcie@11280000/interrupt-controller
[ 0.033312] cryptd: max_cpu_qlen set to 1000
[ 0.035682] SCSI subsystem initialized
[ 0.035840] libata version 3.00 loaded.
[ 0.037576] clocksource: Switched to clocksource arch_sys_counter
[ 0.039863] NET: Registered PF_INET protocol family
[ 0.039964] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 0.041046] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.041061] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.041072] TCP established hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.041090] TCP bind hash table entries: 2048 (order: 4, 65536 bytes, linear)
[ 0.041139] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.041345] MPTCP token hash table entries: 256 (order: 1, 6144 bytes, linear)
[ 0.041445] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.041461] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.041654] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.041687] PCI: CLS 0 bytes, default 64
[ 0.042713] workingset: timestamp_bits=46 max_order=16 bucket_order=0
[ 0.047807] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.047815] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.105272] gpio-export gpio-export: 5 gpio(s) exported
[ 0.106062] mtk-pcie-gen3 11280000.pcie: host bridge /soc/pcie@11280000 ranges:
[ 0.106085] mtk-pcie-gen3 11280000.pcie: Parsing ranges property...
[ 0.106097] mtk-pcie-gen3 11280000.pcie: MEM 0x0020000000..0x002fffffff -> 0x0020000000
[ 0.115811] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled
[ 0.116908] printk: legacy console [ttyS0] disabled
[ 0.137263] 11002000.serial: ttyS0 at MMIO 0x11002000 (irq = 72, base_baud = 2500000) is a ST16650V2
[ 0.137304] printk: legacy console [ttyS0] enabled
[ 0.936426] random: crng init done
[ 0.942772] loop: module loaded
[ 0.948936] spi-nand spi0.0: calibration result: 0x3
[ 0.953999] spi-nand spi0.0: ESMT SPI NAND was found.
[ 0.959080] spi-nand spi0.0: 128 MiB, block size: 128 KiB, page size: 2048, OOB size: 64
[ 0.968013] Signature found at block 1023 [0x07fe0000]
[ 0.973149] NMBM management region starts at block 960 [0x07800000]
[ 0.980644] First info table with writecount 0 found in block 960
[ 0.989747] Second info table with writecount 0 found in block 963
[ 0.995921] NMBM has been successfully attached
[ 1.000666] 6 fixed-partitions partitions found on MTD device spi0.0
[ 1.007258] Creating 6 MTD partitions on "spi0.0":
[ 1.012060] 0x000000000000-0x000000100000 : "BL2"
[ 1.018065] 0x000000100000-0x000000180000 : "u-boot-env"
[ 1.024116] 0x000000180000-0x000000380000 : "Factory"
[ 1.031529] 0x000000380000-0x0000003c0000 : "bdinfo"
[ 1.037307] 0x0000003c0000-0x0000005c0000 : "FIP"
[ 1.043987] 0x0000005c0000-0x0000045c0000 : "ubi"
[ 1.099100] ubi0: default fastmap pool size: 25
[ 1.103632] ubi0: default fastmap WL pool size: 12
[ 1.108433] ubi0: attaching mtd5
[ 1.374626] ubi0: scanning is finished
[ 1.383994] ubi0: attached mtd5 (name "ubi", size 64 MiB)
[ 1.389415] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 1.396277] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 1.403059] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 1.410012] ubi0: good PEBs: 512, bad PEBs: 0, corrupted PEBs: 0
[ 1.416006] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
[ 1.423221] ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 1764728830
[ 1.432348] ubi0: available PEBs: 0, total reserved PEBs: 512, PEBs reserved for bad PEB handling: 19
[ 1.441564] ubi0: background thread "ubi_bgt0d" started, PID 213
[ 1.442279] block ubiblock0_1: created from ubi0:1(rootfs)
[ 1.453059] ubiblock: device ubiblock0_1 (rootfs) set to be root filesystem
[ 1.595223] mtk_soc_eth 15100000.ethernet eth0: mediatek frame engine at 0xffffffc081500000, irq 75
[ 1.605167] i2c_dev: i2c /dev entries driver
[ 1.611201] mtk-wdt 1001c000.watchdog: Watchdog enabled (timeout=31 sec, nowayout=0)
[ 1.620046] NET: Registered PF_INET6 protocol family
[ 1.625770] Segment Routing with IPv6
[ 1.629475] In-situ OAM (IOAM) with IPv6
[ 1.633432] NET: Registered PF_PACKET protocol family
[ 1.638672] 8021q: 802.1Q VLAN Support v1.8
[ 1.661284] phy phy-soc:usb-phy@11e10000.1: type_sw - reg 0x218, index 0
[ 1.668635] mtk-pcie-gen3 11280000.pcie: host bridge /soc/pcie@11280000 ranges:
[ 1.675954] mtk-pcie-gen3 11280000.pcie: Parsing ranges property...
[ 1.682265] mtk-pcie-gen3 11280000.pcie: MEM 0x0020000000..0x002fffffff -> 0x0020000000
[ 1.908266] mtk-pcie-gen3 11280000.pcie: set MEM trans window[0]: cpu_addr = 0x20000000, pci_addr = 0x20000000, size = 0x10000000
[ 1.920230] mtk-pcie-gen3 11280000.pcie: PCI host bridge to bus 0000:00
[ 1.926845] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 1.932339] pci_bus 0000:00: root bus resource [mem 0x20000000-0x2fffffff]
[ 1.939211] pci_bus 0000:00: scanning bus
[ 1.943238] pci 0000:00:00.0: [14c3:1f32] type 01 class 0x060400 PCIe Root Port
[ 1.950561] pci 0000:00:00.0: BAR 0 [mem 0x00000000-0x00007fff 64bit]
[ 1.956995] pci 0000:00:00.0: PCI bridge to [bus 00]
[ 1.961961] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff]
[ 1.968058] pci 0000:00:00.0: bridge window [mem 0x00000000-0x000fffff]
[ 1.974839] pci 0000:00:00.0: bridge window [mem 0x00000000-0x000fffff 64bit pref]
[ 1.982626] pci 0000:00:00.0: PME# supported from D0 D3hot D3cold
[ 1.988718] pci 0000:00:00.0: PME# disabled
[ 1.993976] pci_bus 0000:00: fixups for bus
[ 1.998175] pci 0000:00:00.0: scanning [bus 00-00] behind bridge, pass 0
[ 2.004866] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 2.012869] pci 0000:00:00.0: scanning [bus 00-00] behind bridge, pass 1
[ 2.019649] pci_bus 0000:01: scanning bus
[ 2.023687] pci 0000:01:00.0: [16c3:abcd] type 00 class 0x0d8000 PCIe Endpoint
[ 2.030933] pci 0000:01:00.0: BAR 0 [mem 0x00000000-0x03ffffff pref]
[ 2.037284] pci 0000:01:00.0: BAR 1 [mem 0x00000000-0x0000ffff]
[ 2.043206] pci 0000:01:00.0: BAR 2 [mem 0x00000000-0x01ffffff pref]
[ 2.049563] pci 0000:01:00.0: BAR 3 [mem 0x00000000-0x0000ffff]
[ 2.055478] pci 0000:01:00.0: BAR 4 [mem 0x00000000-0x000fffff]
[ 2.061400] pci 0000:01:00.0: BAR 5 [mem 0x00000000-0x0000ffff]
[ 2.067426] pci 0000:01:00.0: supports D1
[ 2.071434] pci 0000:01:00.0: PME# supported from D0 D1 D3hot D3cold
[ 2.077786] pci 0000:01:00.0: PME# disabled
[ 2.097607] pci_bus 0000:01: fixups for bus
[ 2.101788] pci_bus 0000:01: bus scan returning with max=01
[ 2.107350] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 2.113970] pci_bus 0000:00: bus scan returning with max=01
[ 2.119551] pci 0000:00:00.0: bridge window [mem 0x20000000-0x26ffffff]: assigned
[ 2.127023] pci 0000:00:00.0: BAR 0 [mem 0x27000000-0x27007fff 64bit]: assigned
[ 2.134333] pci 0000:01:00.0: BAR 0 [mem 0x20000000-0x23ffffff pref]: assigned
[ 2.141554] pci 0000:01:00.0: BAR 2 [mem 0x24000000-0x25ffffff pref]: assigned
[ 2.148773] pci 0000:01:00.0: BAR 4 [mem 0x26000000-0x260fffff]: assigned
[ 2.155552] pci 0000:01:00.0: BAR 1 [mem 0x26100000-0x2610ffff]: assigned
[ 2.162340] pci 0000:01:00.0: BAR 3 [mem 0x26110000-0x2611ffff]: assigned
[ 2.169125] pci 0000:01:00.0: BAR 5 [mem 0x26120000-0x2612ffff]: assigned
[ 2.175905] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 2.180864] pci 0000:00:00.0: bridge window [mem 0x20000000-0x26ffffff]
[ 2.187649] pci_bus 0000:00: resource 4 [mem 0x20000000-0x2fffffff]
[ 2.193905] pci_bus 0000:01: resource 1 [mem 0x20000000-0x26ffffff]
[ 2.200189] pci 0000:00:00.0: save config 0x00: 0x1f3214c3
[ 2.205664] pci 0000:00:00.0: save config 0x04: 0x00100000
[ 2.211144] pci 0000:00:00.0: save config 0x08: 0x06040001
[ 2.216619] pci 0000:00:00.0: save config 0x0c: 0x00010000
[ 2.222101] pci 0000:00:00.0: save config 0x10: 0x27000004
[ 2.227581] pci 0000:00:00.0: save config 0x14: 0x00000000
[ 2.233055] pci 0000:00:00.0: save config 0x18: 0x00010100
[ 2.238533] pci 0000:00:00.0: save config 0x1c: 0x000001f1
[ 2.244007] pci 0000:00:00.0: save config 0x20: 0x26f02000
[ 2.249487] pci 0000:00:00.0: save config 0x24: 0x0001fff1
[ 2.254962] pci 0000:00:00.0: save config 0x28: 0x00000000
[ 2.260442] pci 0000:00:00.0: save config 0x2c: 0x00000000
[ 2.265916] pci 0000:00:00.0: save config 0x30: 0x00000000
[ 2.271394] pci 0000:00:00.0: save config 0x34: 0x00000080
[ 2.276868] pci 0000:00:00.0: save config 0x38: 0x00000000
[ 2.282350] pci 0000:00:00.0: save config 0x3c: 0x00020100
[ 2.287942] pcieport 0000:00:00.0: assign IRQ: got 80
[ 2.292989] pcieport 0000:00:00.0: enabling device (0000 -> 0002)
[ 2.299085] pcieport 0000:00:00.0: enabling bus mastering
[ 2.305053] mtk-pcie-gen3 11280000.pcie: msi#0x0 address_hi 0x0 address_lo 0x11280c00 data 0
[ 2.313492] mtk-pcie-gen3 11280000.pcie: msi#0x1 address_hi 0x0 address_lo 0x11280c00 data 1
[ 2.321923] mtk-pcie-gen3 11280000.pcie: msi#0x2 address_hi 0x0 address_lo 0x11280c00 data 2
[ 2.330353] mtk-pcie-gen3 11280000.pcie: msi#0x3 address_hi 0x0 address_lo 0x11280c00 data 3
[ 2.338788] mtk-pcie-gen3 11280000.pcie: msi#0x4 address_hi 0x0 address_lo 0x11280c00 data 4
[ 2.347213] mtk-pcie-gen3 11280000.pcie: msi#0x5 address_hi 0x0 address_lo 0x11280c00 data 5
[ 2.355643] mtk-pcie-gen3 11280000.pcie: msi#0x6 address_hi 0x0 address_lo 0x11280c00 data 6
[ 2.364074] mtk-pcie-gen3 11280000.pcie: msi#0x7 address_hi 0x0 address_lo 0x11280c00 data 7
[ 2.372504] mtk-pcie-gen3 11280000.pcie: msi#0x8 address_hi 0x0 address_lo 0x11280c00 data 8
[ 2.380934] mtk-pcie-gen3 11280000.pcie: msi#0x9 address_hi 0x0 address_lo 0x11280c00 data 9
[ 2.389363] mtk-pcie-gen3 11280000.pcie: msi#0xa address_hi 0x0 address_lo 0x11280c00 data 10
[ 2.397882] mtk-pcie-gen3 11280000.pcie: msi#0xb address_hi 0x0 address_lo 0x11280c00 data 11
[ 2.406394] mtk-pcie-gen3 11280000.pcie: msi#0xc address_hi 0x0 address_lo 0x11280c00 data 12
[ 2.414910] mtk-pcie-gen3 11280000.pcie: msi#0xd address_hi 0x0 address_lo 0x11280c00 data 13
[ 2.423426] mtk-pcie-gen3 11280000.pcie: msi#0xe address_hi 0x0 address_lo 0x11280c00 data 14
[ 2.431943] mtk-pcie-gen3 11280000.pcie: msi#0xf address_hi 0x0 address_lo 0x11280c00 data 15
[ 2.440460] mtk-pcie-gen3 11280000.pcie: msi#0x10 address_hi 0x0 address_lo 0x11280c00 data 16
[ 2.449062] mtk-pcie-gen3 11280000.pcie: msi#0x11 address_hi 0x0 address_lo 0x11280c00 data 17
[ 2.457668] mtk-pcie-gen3 11280000.pcie: msi#0x12 address_hi 0x0 address_lo 0x11280c00 data 18
[ 2.466266] mtk-pcie-gen3 11280000.pcie: msi#0x13 address_hi 0x0 address_lo 0x11280c00 data 19
[ 2.474871] mtk-pcie-gen3 11280000.pcie: msi#0x14 address_hi 0x0 address_lo 0x11280c00 data 20
[ 2.483473] mtk-pcie-gen3 11280000.pcie: msi#0x15 address_hi 0x0 address_lo 0x11280c00 data 21
[ 2.492077] mtk-pcie-gen3 11280000.pcie: msi#0x16 address_hi 0x0 address_lo 0x11280c00 data 22
[ 2.500680] mtk-pcie-gen3 11280000.pcie: msi#0x17 address_hi 0x0 address_lo 0x11280c00 data 23
[ 2.509282] mtk-pcie-gen3 11280000.pcie: msi#0x18 address_hi 0x0 address_lo 0x11280c00 data 24
[ 2.517888] mtk-pcie-gen3 11280000.pcie: msi#0x19 address_hi 0x0 address_lo 0x11280c00 data 25
[ 2.526486] mtk-pcie-gen3 11280000.pcie: msi#0x1a address_hi 0x0 address_lo 0x11280c00 data 26
[ 2.535089] mtk-pcie-gen3 11280000.pcie: msi#0x1b address_hi 0x0 address_lo 0x11280c00 data 27
[ 2.543692] mtk-pcie-gen3 11280000.pcie: msi#0x1c address_hi 0x0 address_lo 0x11280c00 data 28
[ 2.552295] mtk-pcie-gen3 11280000.pcie: msi#0x1d address_hi 0x0 address_lo 0x11280c00 data 29
[ 2.560897] mtk-pcie-gen3 11280000.pcie: msi#0x1e address_hi 0x0 address_lo 0x11280c00 data 30
[ 2.569500] mtk-pcie-gen3 11280000.pcie: msi#0x1f address_hi 0x0 address_lo 0x11280c00 data 31
[ 2.578774] mtk-pcie-gen3 11280000.pcie: msi#0x0 address_hi 0x0 address_lo 0x11280c00 data 0
[ 2.587332] pcieport 0000:00:00.0: PME: Signaling with IRQ 81
[ 2.593293] pcieport 0000:00:00.0: AER: enabled with IRQ 81
[ 2.598975] pcieport 0000:00:00.0: save config 0x00: 0x1f3214c3
[ 2.604888] pcieport 0000:00:00.0: save config 0x04: 0x00100406
[ 2.610819] pcieport 0000:00:00.0: save config 0x08: 0x06040001
[ 2.616729] pcieport 0000:00:00.0: save config 0x0c: 0x00010000
[ 2.622643] pcieport 0000:00:00.0: save config 0x10: 0x27000004
[ 2.628555] pcieport 0000:00:00.0: save config 0x14: 0x00000000
[ 2.634463] pcieport 0000:00:00.0: save config 0x18: 0x00010100
[ 2.640379] pcieport 0000:00:00.0: save config 0x1c: 0x000001f1
[ 2.646287] pcieport 0000:00:00.0: save config 0x20: 0x26f02000
[ 2.652211] pcieport 0000:00:00.0: save config 0x24: 0x0001fff1
[ 2.658126] pcieport 0000:00:00.0: save config 0x28: 0x00000000
[ 2.664034] pcieport 0000:00:00.0: save config 0x2c: 0x00000000
[ 2.669946] pcieport 0000:00:00.0: save config 0x30: 0x00000000
[ 2.675854] pcieport 0000:00:00.0: save config 0x34: 0x00000080
[ 2.681766] pcieport 0000:00:00.0: save config 0x38: 0x00000000
[ 2.687680] pcieport 0000:00:00.0: save config 0x3c: 0x00020150
[ 2.693682] pci 0000:01:00.0: save config 0x00: 0xabcd16c3
[ 2.699170] pci 0000:01:00.0: save config 0x04: 0x00110000
[ 2.704647] pci 0000:01:00.0: save config 0x08: 0x0d800001
[ 2.710128] pci 0000:01:00.0: save config 0x0c: 0x00000000
[ 2.715604] pci 0000:01:00.0: save config 0x10: 0x20000008
[ 2.721083] pci 0000:01:00.0: save config 0x14: 0x26100000
[ 2.726559] pci 0000:01:00.0: save config 0x18: 0x24000008
[ 2.732038] pci 0000:01:00.0: save config 0x1c: 0x26110000
[ 2.737513] pci 0000:01:00.0: save config 0x20: 0x26000000
[ 2.742992] pci 0000:01:00.0: save config 0x24: 0x26120000
[ 2.748471] pci 0000:01:00.0: save config 0x28: 0x00000000
[ 2.753946] pci 0000:01:00.0: save config 0x2c: 0x00000000
[ 2.759429] pci 0000:01:00.0: save config 0x30: 0x00000000
[ 2.764904] pci 0000:01:00.0: save config 0x34: 0x00000040
[ 2.770385] pci 0000:01:00.0: save config 0x38: 0x00000000
[ 2.775861] pci 0000:01:00.0: save config 0x3c: 0x000001ff
[ 2.829084] mt7530-mdio mdio-bus:1f: configuring for fixed/2500base-x link mode
[ 2.837829] mt7530-mdio mdio-bus:1f: Link is Up - 2.5Gbps/Full - flow control rx/tx
[ 2.847938] mt7530-mdio mdio-bus:1f wan (uninitialized): PHY [mt7530-0:00] driver [MediaTek MT7531 PHY] (irq=82)
[ 2.868993] mt7530-mdio mdio-bus:1f lan1 (uninitialized): PHY [mt7530-0:01] driver [MediaTek MT7531 PHY] (irq=83)
[ 2.880971] mtk_soc_eth 15100000.ethernet eth0: entered promiscuous mode
[ 2.887742] DSA: tree 0 setup
[ 2.891010] clk: Disabling unused clocks
[ 2.895177] PM: genpd: Disabling unused power domains
[ 2.905197] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[ 2.912550] Freeing unused kernel memory: 448K
[ 2.917055] Run /sbin/init as init process
[ 2.921158] with arguments:
[ 2.924113] /sbin/init
[ 2.926808] with environment:
[ 2.929942] HOME=/
[ 2.932291] TERM=linux
[ 3.136057] init: Console is alive
[ 3.139639] init: - watchdog -
[ 3.590122] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 3.618757] usbcore: registered new interface driver usbfs
[ 3.624279] usbcore: registered new interface driver hub
[ 3.629651] usbcore: registered new device driver usb
[ 3.635386] gpio_button_hotplug: loading out-of-tree module taints kernel.
[ 3.647146] xhci-mtk 11200000.usb: supply vbus not found, using dummy regulator
[ 3.654997] debugfs: File 'type' in directory 'phy-soc:usb-phy@11e10000.1' already present!
[ 3.663382] debugfs: File 'efuse' in directory 'phy-soc:usb-phy@11e10000.1' already present!
[ 3.671833] debugfs: File 'intr' in directory 'phy-soc:usb-phy@11e10000.1' already present!
[ 3.680185] debugfs: File 'tx-imp' in directory 'phy-soc:usb-phy@11e10000.1' already present!
[ 3.688703] debugfs: File 'rx-imp' in directory 'phy-soc:usb-phy@11e10000.1' already present!
[ 3.697459] xhci-mtk 11200000.usb: xHCI Host Controller
[ 3.702714] xhci-mtk 11200000.usb: new USB bus registered, assigned bus number 1
[ 3.713132] xhci-mtk 11200000.usb: hcc params 0x01403f99 hci version 0x110 quirks 0x0000000000200010
[ 3.722303] xhci-mtk 11200000.usb: irq 84, io mem 0x11200000
[ 3.728073] xhci-mtk 11200000.usb: xHCI Host Controller
[ 3.733293] xhci-mtk 11200000.usb: new USB bus registered, assigned bus number 2
[ 3.740690] xhci-mtk 11200000.usb: Host supports USB 3.2 Enhanced SuperSpeed
[ 3.748258] hub 1-0:1.0: USB hub found
[ 3.752031] hub 1-0:1.0: 1 port detected
[ 3.756240] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 3.764693] hub 2-0:1.0: USB hub found
[ 3.768483] hub 2-0:1.0: 1 port detected
[ 3.777117] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 3.788603] init: - preinit -
[ 3.829649] pcieport 0000:00:00.0: AER: Uncorrectable (Fatal) error message received from 0000:00:00.0
[ 3.839017] pcieport 0000:00:00.0: PCIe Bus Error: severity=Uncorrectable (Fatal), type=Transaction Layer, (Receiver ID)
[ 3.849904] pcieport 0000:00:00.0: device [14c3:1f32] error status/mask=00000020/00400000
[ 3.858257] pcieport 0000:00:00.0: [ 5] SDES (First)
[ 3.865043] pcieport 0000:00:00.0: AER: broadcast error_detected message
[ 3.871765] pci 0000:01:00.0: AER: can't recover (no error_detected callback)
[ 3.897586] pcieport 0000:00:00.0: waiting 100 ms for downstream link
[ 4.066301] pci 0000:01:00.0: ready 0ms after bus reset
[ 4.071541] pcieport 0000:00:00.0: AER: Root Port link has been reset (0)
[ 4.078383] pcieport 0000:00:00.0: AER: device recovery failed
[ 4.207865] mtk_soc_eth 15100000.ethernet eth0: configuring for fixed/2500base-x link mode
[ 4.216325] mtk_soc_eth 15100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx
[ 4.247068] mt7530-mdio mdio-bus:1f lan1: configuring for phy/gmii link mode
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 5.749894] mt7530-mdio mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control rx/tx
[ 8.408754] UBIFS (ubi0:2): Mounting in unauthenticated mode
[ 8.414512] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" started, PID 736
[ 8.447780] UBIFS (ubi0:2): recovery needed
[ 8.493811] UBIFS (ubi0:2): recovery completed
[ 8.498328] UBIFS (ubi0:2): UBIFS: mounted UBI device 0, volume 2, name "rootfs_data"
[ 8.506149] UBIFS (ubi0:2): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 8.516056] UBIFS (ubi0:2): FS size: 48250880 bytes (46 MiB, 380 LEBs), max 390 LEBs, journal size 2412544 bytes (2 MiB, 19 LEBs)
[ 8.527700] UBIFS (ubi0:2): reserved for root: 2279008 bytes (2225 KiB)
[ 8.534303] UBIFS (ubi0:2): media format: w5/r0 (latest is w5/r0), UUID 11449A0D-2B68-4853-A0C1-9314BF72B6F4, small LPT model
[ 8.546498] mount_root: overlay filesystem has not been fully initialized yet
[ 8.555799] mount_root: switching to ubifs overlay
[ 8.564867] overlayfs: null uuid detected in lower fs '/', falling back to xino=off,index=off,nfs_export=off.
[ 8.578834] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 8.632892] mt7530-mdio mdio-bus:1f lan1: Link is Down
[ 8.642145] procd: - early -
[ 8.645087] procd: - watchdog -
[ 9.199174] procd: - watchdog -
[ 9.211363] procd: - ubus -
[ 9.370677] procd: - init -
Please press Enter to activate this console.
[ 9.706039] kmodloader: loading kernel modules from /etc/modules.d/*
[ 9.737287] sprd_pci_ep_dev_init Quectel_Linux&Android_SPRD_PCIE_Driver_V1.1.9
[ 9.793884] sprd-pcie-ep-device 0000:01:00.0: assign IRQ: got 0
[ 9.793884] pcieport 0000:00:00.0: AER: Uncorrectable (Non-Fatal) error message received from 0000:00:00.0
[ 9.793901] pcieport 0000:00:00.0: PCIe Bus Error: severity=Uncorrectable (Non-Fatal), type=Transaction Layer, (Requester ID)
[ 9.820733] pcieport 0000:00:00.0: device [14c3:1f32] error status/mask=00004020/00400000
[ 9.829084] pcieport 0000:00:00.0: [ 5] SDES (First)
[ 9.835861] pcieport 0000:00:00.0: [14] CmpltTO
[ 9.848851] sprd-pcie-ep-device 0000:01:00.0: ep: probe
[ 9.848852] pcieport 0000:00:00.0: AER: broadcast error_detected message
[ 9.959822] sprd-pcie-ep-device 0000:01:00.0: enabling device (0000 -> 0002)
[ 10.116790] sprd-pcie-ep-device 0000:01:00.0: enabling bus mastering
[ 10.174088] sipc init dma_alloc_coherent smem_hwaddr:0000000043400000, u32:43400000
[ 10.181744] sipc init dma_alloc_coherent smem_vaddr:ffffffc081acd000, u64:81acd000
[ 10.189303] sipc: name=sprd,sipc
[ 10.192520] sipc: type=1
[ 10.195042] sipc: dst =1
[ 10.197568] sipc: ep_dev=0
[ 10.200263] sipc: smem_type = 0
[ 10.203392] sipc: smem_base=0x81acd000, dst_smem_base=0x43400000, smem_size=0x300000
[ 10.211124] sipc: high_offset=0x0n
[ 10.211128] smsg_ipc_create: sprd,sipc
[ 10.291951] urngd: v1.0.2 started.
[ 10.427573] smem_init: pool addr = 0x81acd000, size = 0x300000 added.
[ 10.434015] smsg_ipc_smem_init: ring_base = 0x81acd000, ring_size = 0x1000
[ 10.441429] spipe_probe!
[ 10.443962] spipe: after parse device tree, name=spipe_nr, dst=1, channel=4, ringnr=15, rxbuf_size=0x1000, txbuf_size=0x1000
[ 10.455279] sbuf_host_init: channel 1-4, offset = 0x0!
[ 10.460643] smsg_ch_open: channel 1-4 send open msg!
[ 10.461257] spipe_probe!
[ 10.465630] pcie res: request resource, state=0.
[ 10.468153] spipe: after parse device tree, name=sdiag_nr, dst=1, channel=21, ringnr=1, rxbuf_size=0x8000, txbuf_size=0x40000
[ 10.484149] sbuf_host_init: channel 1-21, offset = 0x0!
[ 10.489521] smsg_ch_open: channel 1-21 send open msg!
[ 10.489655] spipe_probe!
[ 10.497091] spipe: after parse device tree, name=stty_nr, dst=1, channel=6, ringnr=32, rxbuf_size=0x800, txbuf_size=0x800
[ 10.508147] sbuf_host_init: channel 1-6, offset = 0x0!
[ 10.513852] smsg_ch_open: channel 1-6 send open msg!
[ 10.515024] spipe_probe!
[ 10.521373] spipe: after parse device tree, name=snv_nr, dst=1, channel=40, ringnr=1, rxbuf_size=0x1000, txbuf_size=0x40400
[ 10.532631] sbuf_host_init: channel 1-40, offset = 0x0!
[ 10.539334] spool: name=slog_nr, dst=1, channel=5, pre_cfg=0
[ 10.544996] spool: tx_num=0, tx_size=0, rx_num=32, rx_size=65536
[ 10.551070] smsg_ch_open: channel 1-40 send open msg!
[ 10.556203] smsg_ch_open: channel 1-5 send open msg!
[ 10.556340] sprd-pcie-ep-device 0000:01:00.0: ep: BAR[0] [mem 0x20000000-0x23ffffff pref]
[ 10.569408] sprd-pcie-ep-device 0000:01:00.0: ep: BAR[1] [mem 0x26100000-0x2610ffff]
[ 10.577147] sprd-pcie-ep-device 0000:01:00.0: ep: BAR[2] [mem 0x24000000-0x25ffffff pref]
[ 10.585319] sprd-pcie-ep-device 0000:01:00.0: ep: BAR[3] [mem 0x26110000-0x2611ffff]
[ 10.593055] sprd-pcie-ep-device 0000:01:00.0: ep: BAR[4] [mem 0x26000000-0x260fffff]
[ 10.600792] sprd-pcie-ep-device 0000:01:00.0: ep: BAR[5] [mem 0x26120000-0x2612ffff]
[ 10.657669] sprd-pcie-ep-device 0000:01:00.0: ep: atu_view_port val = 0x0
[ 10.664450] sprd-pcie-ep-device 0000:01:00.0: ep: Interrupt type:intx, irq=0
[ 10.671498] sprd_ep_map_memory: get bar = 2
[ 10.725644] Internal error: synchronous external abort: 0000000096000210 [#1] SMP
[ 10.733114] Modules linked in: sprd_pcie(O+) sha512_arm64 sha1_ce sha1_generic seqiv md5 geniv des_generic libdes authencesn authenc leds_gpio xhci_plat_hcd xhci_pci xhci_mtk_hcd xhci_hcd gpio_button_hotplug(O) usbcore usb_common mii
[ 10.753824] CPU: 0 UID: 0 PID: 915 Comm: kmodloader Tainted: G M O 6.12.85 #0
[ 10.762164] Tainted: [M]=MACHINE_CHECK, [O]=OOT_MODULE
[ 10.767289] Hardware name: Cudy P2 5G (DT)
[ 10.771373] pstate: 60400005 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 10.778322] pc : 0xffffffc078e8f000
[ 10.781829] lr : cleanup_module+0x280/0x830 [sprd_pcie]
[ 10.787064] sp : ffffffc081acb7e0
[ 10.790366] x29: ffffffc081acb7e0 x28: ffffffc078eb0278 x27: ffffff8000b630c8
[ 10.797494] x26: ffffffc078eadf88 x25: 0000000001004000 x24: 0000000000000002
[ 10.804621] x23: 0000000028000000 x22: 0000000000000000 x21: 0000000000000005
[ 10.811748] x20: ffffff8001440680 x19: 0000000000010908 x18: ffffffc080c6e9e8
[ 10.818876] x17: 3278302d30303030 x16: 323136327830206d x15: 00000000000001af
[ 10.826003] x14: 00000000000001af x13: 00000000ffffffea x12: ffffffc080cc6990
[ 10.833130] x11: 0000000000000000 x10: 0000000000000002 x9 : 000000000000b222
[ 10.840257] x8 : 00000000000002b5 x7 : ffffffc084000000 x6 : 0000000000000048
[ 10.847384] x5 : ffffff800ff37020 x4 : 0000000000000000 x3 : 0000000000000001
[ 10.854511] x2 : ffffffc082210900 x1 : ffffffc082210908 x0 : ffffffc082210908
[ 10.861639] Call trace:
[ 10.864074] 0xffffffc078e8f000
[ 10.867226] sprd_ep_map_memory+0x1e8/0x2cc [sprd_pcie]
[ 10.872459] cleanup_module+0x60c/0x830 [sprd_pcie]
[ 10.877346] pci_device_probe+0x94/0x12c
[ 10.881262] really_probe+0xb8/0x2a4
[ 10.884829] __driver_probe_device+0x74/0x118
[ 10.889174] driver_probe_device+0x3c/0xe0
[ 10.893260] __driver_attach+0x88/0x154
[ 10.897086] bus_for_each_dev+0x60/0xa0
[ 10.900914] driver_attach+0x20/0x28
[ 10.904480] bus_add_driver+0xdc/0x200
[ 10.908217] driver_register+0x64/0x114
[ 10.912043] __pci_register_driver+0x40/0x48
[ 10.916302] init_module+0x80/0x1000 [sprd_pcie]
[ 10.920930] do_one_initcall+0x4c/0x1f8
[ 10.924757] do_init_module+0x50/0x1ec
[ 10.928499] load_module+0x1488/0x195c
[ 10.932239] __do_sys_init_module+0x1b0/0x264
[ 10.936588] __arm64_sys_init_module+0x18/0x20
[ 10.941022] invoke_syscall.constprop.0+0x4c/0xd0
[ 10.945716] do_el0_svc+0x3c/0xd0
[ 10.949021] el0_svc+0x18/0x60
[ 10.952069] el0t_64_sync_handler+0x118/0x124
[ 10.956416] el0t_64_sync+0x150/0x154
[ 10.960074] Code: ???????? ???????? ???????? ???????? (b9400000)
[ 10.966154] ---[ end trace 0000000000000000 ]---
[ 10.977788] pstore: backend (ramoops) writing error (-28)
[ 10.983181] Kernel panic - not syncing: synchronous external abort: Fatal exception
[ 10.990823] SMP: stopping secondary CPUs
[ 10.994737] Kernel Offset: disabled
[ 10.998213] CPU features: 0x00,00000000,00000000,4200400b
[ 11.003600] Memory Limit: none
[ 11.013626] Rebooting in 1 seconds..