FAQ o OpenWrt | Sprzedam różne routery | Oddam

lukasz3134 · 2026-05-09 09:03:00

lukasz3134
Użytkownik
Nieaktywny

Skąd: Tomaszów Mazowiecki
Zarejestrowany: 2025-05-22
Posty: 270

Odp: Cudy P2 5G v1.0 - wsparcie OpenWRT

A i kolejna sprawa. W oprogramowaniu cudy, adres mac na nalepce routera jest przypisany do portu lan. W moim initramfs jest przypisany do eth0 i do portu wan. Więc jak to teraz odwrócić ?

lukasz3134 · 2026-05-09 09:17:27

lukasz3134
Użytkownik
Nieaktywny

Skąd: Tomaszów Mazowiecki
Zarejestrowany: 2025-05-22
Posty: 270

Odp: Cudy P2 5G v1.0 - wsparcie OpenWRT

Hmm, zmieniłem nazwę portu lan1 w dts na lan, i przestał on działać. WAN działa dalej...

lukasz3134 · 2026-05-09 09:40:01

lukasz3134
Użytkownik
Nieaktywny

Skąd: Tomaszów Mazowiecki
Zarejestrowany: 2025-05-22
Posty: 270

Odp: Cudy P2 5G v1.0 - wsparcie OpenWRT

Dobra, główny adres mac jest na porcie lan i się zgadza. Modem prezentuje się na usb jako Quectel RG5500U-EB i ma ID 2c7c-0900. Natomiast w dalszym ciągu mam 4 porty lan i 1 wan w luci, mimo że edytowałem plik 02_board.

lukasz3134 · 2026-05-09 10:02:32

lukasz3134
Użytkownik
Nieaktywny

Skąd: Tomaszów Mazowiecki
Zarejestrowany: 2025-05-22
Posty: 270

Odp: Cudy P2 5G v1.0 - wsparcie OpenWRT

Prosze państwa, mamy to !! Sysupgrade z poziomu konsoli przez sysupgrade -n działa, oto log:

Thu Jan  1 00:04:18 GMT 1970 upgrade: Sending TERM to remaining processes ...
Thu Jan  1 00:04:22 GMT 1970 upgrade: Sending KILL to remaining processes ...
[  268.819245] stage2 (3493): drop_caches: 3
Thu Jan  1 00:04:28 GMT 1970 upgrade: Switching to ramdisk...
Thu Jan  1 00:04:29 UTC 1970 upgrade: Performing system upgrade...
verifying sysupgrade tar file integrity
[  270.260515] block ubiblock0_1: released
[  270.321617] ubi0: reserved more 2 PEBs for bad PEB handling
Volume ID 0, size 37 LEBs (4698112 bytes, 4.4 MiB), LEB size 126976 bytes (124.0 KiB), dynamic, name "kernel", alignment 1
[  270.894392] block ubiblock0_1: created from ubi0:1(rootfs)
Volume ID 1, size 50 LEBs (6348800 bytes, 6.0 MiB), LEB size 126976 bytes (124.0 KiB), dynamic, name "rootfs", alignment 1
Set volume size to 50790400
Volume ID 2, size 400 LEBs (50790400 bytes, 48.4 MiB), LEB size 126976 bytes (124.0 KiB), dynamic, name "rootfs_data", alignment 1
sysupgrade successful
umount: can't unmount /dev: Resource busy
umoun[  274.402247] mt7530-mdio mdio-bus:1f lan1: Link is Down
t: can't unmount /tmp: Resource [  274.410052] br-lan: port 1(lan1) entered disabled state
busy
[  274.417790] mtk_soc_eth 15100000.ethernet eth0: Link is Down
[  274.427057] reboot: Restarting system

F0: 102B 0000
FA: 1040 0000
FA: 1040 0000 [0200]
F9: 0000 0000
V0: 0000 0000 [0001]
00: 0000 0000
BP: 2400 0041 [0000]
G0: 1190 0000
EC: 0000 0000 [1000]
T0: 0000 0252 [010F]
Jump to BL

NOTICE:  BL2: v2.7(release):f0ff4aea06-dirty
NOTICE:  BL2: Built : 11:23:05, Sep 18 2025
NOTICE:  WDT: disabled
NOTICE:  EMI: Using DDR3 settings

dump toprgu registers data:
1001c000 | 00000000 0000ffe0 00000000 00000000
1001c010 | 00000fff 00000000 00f00000 00000000
1001c020 | 00000000 00000000 00000000 00000000
1001c030 | 003c0003 003c0003 00000000 00000000
1001c040 | 00000000 00000000 00000000 00000000
1001c050 | 00000000 00000000 00000000 00000000
1001c060 | 00000000 00000000 00000000 00000000
1001c070 | 00000000 00000000 00000000 00000000
1001c080 | 00000000 00000000 00000000 00000000

dump drm registers data:
1001d000 | 00000000 00000000 00000000 00000000
1001d010 | 00000000 00000000 00000000 00000000
1001d020 | 00000000 00000000 00000000 00000000
1001d030 | 00a003f1 000000ff 00100000 00000000
1001d040 | 00027e71 000200a0 00020303 000000ff
1001d050 | 00000000 00000000 00000000 00000000
1001d060 | 00000002 00000000 00000000 00000000
drm: 500 = 0xc
[DDR Reserve] ddr reserve mode not be enabled yet
DDR RESERVE Success 0
[EMI] ComboMCP not ready, using default setting
BYTE_swap:0
BYTE_swap:0
Window Sum 588, worse bit 0, min window 72
Window Sum 592, worse bit 8, min window 72
Window Sum 390, worse bit 3, min window 46
Window Sum 376, worse bit 8, min window 46
Window Sum 400, worse bit 3, min window 48
Window Sum 384, worse bit 9, min window 46
Window Sum 408, worse bit 2, min window 50
Window Sum 396, worse bit 8, min window 48
Window Sum 416, worse bit 3, min window 50
Window Sum 408, worse bit 9, min window 48
Window Sum 426, worse bit 3, min window 52
Window Sum 420, worse bit 9, min window 50
Window Sum 436, worse bit 0, min window 54
Window Sum 428, worse bit 9, min window 52
Window Sum 444, worse bit 3, min window 54
Window Sum 436, worse bit 8, min window 54
Window Sum 450, worse bit 0, min window 56
Window Sum 442, worse bit 8, min window 54
Window Sum 458, worse bit 2, min window 56
Window Sum 452, worse bit 14, min window 54
Window Sum 464, worse bit 3, min window 56
Window Sum 462, worse bit 9, min window 56
Window Sum 476, worse bit 4, min window 58
Window Sum 466, worse bit 9, min window 56
Window Sum 480, worse bit 5, min window 58
Window Sum 478, worse bit 14, min window 58
Window Sum 488, worse bit 3, min window 60
Window Sum 480, worse bit 8, min window 58
NOTICE:  EMI: Detected DRAM size: 256MB
NOTICE:  EMI: complex R/W mem test passed
NOTICE:  CPU: MT7981 (1300MHz)
NOTICE:  SPI_NAND parses attributes from parameter page.
NOTICE:  SPI_NAND Detected ID 0x8c
NOTICE:  Page size 2048, Block size 131072, size 134217728
NOTICE:  Initializing NMBM ...
NOTICE:  Signature found at block 1023 [0x07fe0000]
NOTICE:  First info table with writecount 0 found in block 960
NOTICE:  Second info table with writecount 0 found in block 963
NOTICE:  NMBM has been successfully attached in read-only mode
NOTICE:  BL2: Booting BL31
NOTICE:  BL31: v2.7(release):f0ff4aea06-dirty
NOTICE:  BL31: Built : 11:23:05, Sep 18 2025
NOTICE:  Hello BL31!!!


U-Boot 2022.07-rc3 (Sep 18 2025 - 11:23:05 +0000), Build: jenkins-mtk_mt7981_router_v2.4-46

CPU:   MediaTek MT7981
Model: mt7981-rfb
DRAM:  256 MiB
Core:  48 devices, 20 uclasses, devicetree: embed

Initializing NMBM ...
spi-nand: spi_nand spi_nand@0: ESMT SPI NAND was found.
spi-nand: spi_nand spi_nand@0: 128 MiB, block size: 128 KiB, page size: 2048, OOB size: 64
Could not find a valid device for nmbm0
Signature found at block 1023 [0x07fe0000]
First info table with writecount 0 found in block 960
Second info table with writecount 0 found in block 963
NMBM has been successfully attached

Loading Environment from MTD... *** Warning - bad CRC, using default environment

In:    serial@11002000
Out:   serial@11002000
Err:   serial@11002000
Net:
Warning: ethernet@15100000 (eth0) using random MAC address - 9e:af:37:4b:37:23
eth0: ethernet@15100000
gpio: pin 6 (gpio 6) value is 0
gpio: pin 8 (gpio 8) value is 0
ubi0: attaching mtd7
ubi0: scanning is finished
ubi0: attached mtd7 (name "ubi", size 64 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 512, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 8/3, WL threshold: 4096, image sequence number: 1792215068
ubi0: available PEBs: 2, total reserved PEBs: 510, PEBs reserved for bad PEB handling: 19
Reading from volume 'kernel' to 0x46000000, size 0x0 ... OK
## Loading kernel from FIT Image at 46000000 ...
   Using 'config-1' configuration
   Trying 'kernel-1' kernel subimage
     Description:  ARM64 OpenWrt Linux-6.18.26
     Type:         Kernel Image
     Compression:  lzma compressed
     Data Start:   0x460000e8
     Data Size:    4665732 Bytes = 4.4 MiB
     Architecture: AArch64
     OS:           Linux
     Load Address: 0x48000000
     Entry Point:  0x48000000
     Hash algo:    crc32
     Hash value:   0cade335
     Hash algo:    sha1
     Hash value:   4edc5a586df42a2eea958b895b2ddc91c1db66ed
   Verifying Hash Integrity ... crc32+ sha1+ OK
## Loading fdt from FIT Image at 46000000 ...
   Using 'config-1' configuration
   Trying 'fdt-1' fdt subimage
     Description:  ARM64 OpenWrt cudy_p2-5g device tree blob
     Type:         Flat Device Tree
     Compression:  uncompressed
     Data Start:   0x464733a8
     Data Size:    22636 Bytes = 22.1 KiB
     Architecture: AArch64
     Hash algo:    crc32
     Hash value:   f8fb75dc
     Hash algo:    sha1
     Hash value:   e5abec929228a07aed07d65195f0d262ffc9ee3d
   Verifying Hash Integrity ... crc32+ sha1+ OK
   Booting using the fdt blob at 0x464733a8
   Uncompressing Kernel Image
   Loading Device Tree to 000000004f7f0000, end 000000004f7f886b ... OK

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[    0.000000] Linux version 6.18.26 (lukasz@lukasz-mint) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 14.3.0 r34342-472c325fb8) 14.3.0, GNU ld (GNU Binutils) 2.44) #0 SMP Thu May  7 19:14:08 2026
[    0.000000] KASLR disabled due to lack of seed
[    0.000000] Machine model: Cudy P2 5G
[    0.000000] OF: reserved mem: 0x0000000042ff0000..0x0000000042ffffff (64 KiB) map non-reusable ramoops@42ff0000
[    0.000000] OF: reserved mem: 0x0000000043000000..0x000000004302ffff (192 KiB) nomap non-reusable secmon@43000000
[    0.000000] OF: reserved mem: 0x0000000047c80000..0x0000000047d7ffff (1024 KiB) nomap non-reusable wmcpu-reserved@47c80000
[    0.000000] OF: reserved mem: 0x0000000047d80000..0x0000000047dbffff (256 KiB) nomap non-reusable wo-emi@47d80000
[    0.000000] OF: reserved mem: 0x0000000047dc0000..0x0000000047ffffff (2304 KiB) nomap non-reusable wo-data@47dc0000
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000040000000-0x000000004fffffff]
[    0.000000]   DMA32    empty
[    0.000000]   Normal   empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000040000000-0x0000000042ffffff]
[    0.000000]   node   0: [mem 0x0000000043000000-0x000000004302ffff]
[    0.000000]   node   0: [mem 0x0000000043030000-0x0000000047c7ffff]
[    0.000000]   node   0: [mem 0x0000000047c80000-0x0000000047ffffff]
[    0.000000]   node   0: [mem 0x0000000048000000-0x000000004fffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000004fffffff]
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.1 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] psci: SMC Calling Convention v1.2
[    0.000000] percpu: Embedded 20 pages/cpu s43480 r8192 d30248 u81920
[    0.000000] pcpu-alloc: s43480 r8192 d30248 u81920 alloc=20*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1
[    0.000000] Detected VIPT I-cache on CPU0
[    0.000000] CPU features: detected: GICv3 CPU interface
[    0.000000] CPU features: kernel page table isolation disabled by kernel configuration
[    0.000000] alternatives: applying boot alternatives
[    0.000000] Kernel command line:
[    0.000000] printk: log buffer data + meta data: 131072 + 458752 = 589824 bytes
[    0.000000] Dentry cache hash table entries: 32768 (order: 6, 262144 bytes, linear)
[    0.000000] Inode-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
[    0.000000] software IO TLB: SWIOTLB bounce buffer size adjusted to 0MB
[    0.000000] software IO TLB: area num 2.
[    0.000000] software IO TLB: SWIOTLB bounce buffer size roundup to 0MB
[    0.000000] software IO TLB: mapped [mem 0x000000004fe4b000-0x000000004fecb000] (0MB)
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 65536
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] rcu: Hierarchical RCU implementation.
[    0.000000] rcu:     RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000]  Tracing variant of Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] RCU Tasks Trace: Setting shift to 1 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=2.
[    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[    0.000000] GICv3: GIC: Using split EOI/Deactivate mode
[    0.000000] GICv3: 640 SPIs implemented
[    0.000000] GICv3: 0 Extended SPIs implemented
[    0.000000] Root IRQ handler: gic_handle_irq
[    0.000000] GICv3: GICv3 features: 16 PPIs
[    0.000000] GICv3: GICD_CTLR.DS=0, SCR_EL3.FIQ=0
[    0.000000] GICv3: CPU0: found redistributor 0 region 0:0x000000000c080000
[    0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[    0.000000] arch_timer: cp15 timer running at 13.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2ff89eacb, max_idle_ns: 440795202429 ns
[    0.000000] sched_clock: 56 bits at 13MHz, resolution 76ns, wraps every 4398046511101ns
[    0.000089] Calibrating delay loop (skipped), value calculated using timer frequency.. 26.00 BogoMIPS (lpj=130000)
[    0.000097] pid_max: default: 32768 minimum: 301
[    0.002510] Mount-cache hash table entries: 512 (order: 0, 4096 bytes, linear)
[    0.002518] Mountpoint-cache hash table entries: 512 (order: 0, 4096 bytes, linear)
[    0.007571] cacheinfo: Unable to detect cache hierarchy for CPU 0
[    0.008339] rcu: Hierarchical SRCU implementation.
[    0.008346] rcu:     Max phase no-delay instances is 1000.
[    0.008561] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level
[    0.008767] smp: Bringing up secondary CPUs ...
[    0.009151] Detected VIPT I-cache on CPU1
[    0.009196] GICv3: CPU1: found redistributor 1 region 0:0x000000000c0a0000
[    0.009223] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[    0.009302] smp: Brought up 1 node, 2 CPUs
[    0.009307] SMP: Total of 2 processors activated.
[    0.009310] CPU: All CPU(s) started at EL2
[    0.009313] CPU features: detected: 32-bit EL0 Support
[    0.009316] CPU features: detected: CRC32 instructions
[    0.009343] alternatives: applying system-wide alternatives
[    0.009487] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching
[    0.009615] Memory: 235624K/262144K available (9664K kernel code, 1014K rwdata, 2972K rodata, 960K init, 295K bss, 24812K reserved, 0K cma-reserved)
[    0.012904] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.012930] posixtimers hash table entries: 1024 (order: 2, 16384 bytes, linear)
[    0.012956] futex hash table entries: 512 (32768 bytes on 1 NUMA nodes, total 32 KiB, linear).
[    0.012994] 28992 pages in range for non-PLT usage
[    0.012996] 520512 pages in range for PLT usage
[    0.014578] pinctrl core: initialized pinctrl subsystem
[    0.015782] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[    0.016081] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations
[    0.016106] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[    0.016127] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[    0.016539] thermal_sys: Registered thermal governor 'fair_share'
[    0.016543] thermal_sys: Registered thermal governor 'bang_bang'
[    0.016546] thermal_sys: Registered thermal governor 'step_wise'
[    0.016549] thermal_sys: Registered thermal governor 'user_space'
[    0.016611] ASID allocator initialised with 65536 entries
[    0.017286] pstore: Using crash dump compression: deflate
[    0.017291] pstore: Registered ramoops as persistent store backend
[    0.017293] ramoops: using 0x10000@0x42ff0000, ecc: 0
[    0.018937] /soc/interrupt-controller@c000000: Fixed dependency cycle(s) with /soc/interrupt-controller@c000000
[    0.020270] /soc/pcie@11280000: Fixed dependency cycle(s) with /soc/pcie@11280000/interrupt-controller
[    0.038301] SCSI subsystem initialized
[    0.038471] libata version 3.00 loaded.
[    0.040195] clocksource: Switched to clocksource arch_sys_counter
[    0.042627] NET: Registered PF_INET protocol family
[    0.042726] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear)
[    0.043779] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear)
[    0.043792] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.043806] TCP established hash table entries: 2048 (order: 2, 16384 bytes, linear)
[    0.043825] TCP bind hash table entries: 2048 (order: 4, 65536 bytes, linear)
[    0.043873] TCP: Hash tables configured (established 2048 bind 2048)
[    0.044085] MPTCP token hash table entries: 256 (order: 1, 6144 bytes, linear)
[    0.044191] UDP hash table entries: 256 (order: 2, 16384 bytes, linear)
[    0.044211] UDP-Lite hash table entries: 256 (order: 2, 16384 bytes, linear)
[    0.044415] NET: Registered PF_UNIX/PF_LOCAL protocol family
[    0.044448] PCI: CLS 0 bytes, default 64
[    0.045457] workingset: timestamp_bits=46 max_order=16 bucket_order=0
[    0.050645] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.050653] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.053988] cryptd: max_cpu_qlen set to 1000
[    0.108153] gpio-export gpio-export: 5 gpio(s) exported
[    0.109185] mtk-pcie-gen3 11280000.pcie: host bridge /soc/pcie@11280000 ranges:
[    0.109208] mtk-pcie-gen3 11280000.pcie: Parsing ranges property...
[    0.109218] mtk-pcie-gen3 11280000.pcie:      MEM 0x0020000000..0x002fffffff -> 0x0020000000
[    0.113172] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled
[    0.114377] printk: legacy console [ttyS0] disabled
[    0.134758] 11002000.serial: ttyS0 at MMIO 0x11002000 (irq = 72, base_baud = 2500000) is a ST16650V2
[    0.134799] printk: legacy console [ttyS0] enabled
[    0.953503] mtk_rng trng: registered RNG driver
[    0.953543] random: crng init done
[    0.964533] loop: module loaded
[    0.970554] spi-nand spi0.0: calibration result: 0x3
[    0.975611] spi-nand spi0.0: ESMT SPI NAND was found.
[    0.980668] spi-nand spi0.0: 128 MiB, block size: 128 KiB, page size: 2048, OOB size: 64
[    0.989220] Signature found at block 1023 [0x07fe0000]
[    0.994372] NMBM management region starts at block 960 [0x07800000]
[    1.001752] First info table with writecount 0 found in block 960
[    1.010717] Second info table with writecount 0 found in block 963
[    1.016898] NMBM has been successfully attached
[    1.021642] 6 fixed-partitions partitions found on MTD device spi0.0
[    1.028243] Creating 6 MTD partitions on "spi0.0":
[    1.033069] 0x000000000000-0x000000100000 : "BL2"
[    1.038988] 0x000000100000-0x000000180000 : "u-boot-env"
[    1.045117] 0x000000180000-0x000000380000 : "Factory"
[    1.052429] 0x000000380000-0x0000003c0000 : "bdinfo"
[    1.058239] 0x0000003c0000-0x0000005c0000 : "FIP"
[    1.064992] 0x0000005c0000-0x0000045c0000 : "ubi"
[    1.119962] ubi0: default fastmap pool size: 25
[    1.124524] ubi0: default fastmap WL pool size: 12
[    1.129308] ubi0: attaching mtd5
[    1.397110] ubi0: scanning is finished
[    1.406509] ubi0: attached mtd5 (name "ubi", size 64 MiB)
[    1.411930] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    1.418792] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    1.425573] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[    1.432531] ubi0: good PEBs: 512, bad PEBs: 0, corrupted PEBs: 0
[    1.438524] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
[    1.445737] ubi0: max/mean erase counter: 8/3, WL threshold: 4096, image sequence number: 1792215068
[    1.454862] ubi0: available PEBs: 0, total reserved PEBs: 512, PEBs reserved for bad PEB handling: 19
[    1.464082] ubi0: background thread "ubi_bgt0d" started, PID 214
[    1.464792] block ubiblock0_1: created from ubi0:1(rootfs)
[    1.475584] ubiblock: device ubiblock0_1 (rootfs) set to be root filesystem
[    1.487323] mtk_soc_eth 15100000.ethernet: legacy DT: using hard-coded SRAM offset.
[    1.495350] mtk_soc_eth 15100000.ethernet: legacy DT: missing interrupt-names.
[    1.637937] mtk_soc_eth 15100000.ethernet eth0: mediatek frame engine at 0xffffffc081700000, irq 75
[    1.647796] i2c_dev: i2c /dev entries driver
[    1.654033] mtk-wdt 1001c000.watchdog: Watchdog enabled (timeout=31 sec, nowayout=0)
[    1.662879] NET: Registered PF_INET6 protocol family
[    1.668702] Segment Routing with IPv6
[    1.672431] In-situ OAM (IOAM) with IPv6
[    1.676402] NET: Registered PF_PACKET protocol family
[    1.681736] 8021q: 802.1Q VLAN Support v1.8
[    1.703586] phy phy-soc:usb-phy@11e10000.1: type_sw - reg 0x218, index 0
[    1.712587] mtk-pcie-gen3 11280000.pcie: host bridge /soc/pcie@11280000 ranges:
[    1.719908] mtk-pcie-gen3 11280000.pcie: Parsing ranges property...
[    1.726225] mtk-pcie-gen3 11280000.pcie:      MEM 0x0020000000..0x002fffffff -> 0x0020000000
[    1.777662] mt7530-mdio mdio-bus:1f: configuring for fixed/2500base-x link mode
[    1.786403] mt7530-mdio mdio-bus:1f: Link is Up - 2.5Gbps/Full - flow control rx/tx
[    1.804237] mt7530-mdio mdio-bus:1f wan (uninitialized): PHY [mt7530-0:00] driver [MediaTek MT7531 PHY] (irq=78)
[    1.829834] mt7530-mdio mdio-bus:1f lan1 (uninitialized): PHY [mt7530-0:01] driver [MediaTek MT7531 PHY] (irq=79)
[    1.846161] mtk_soc_eth 15100000.ethernet eth0: entered promiscuous mode
[    1.852920] DSA: tree 0 setup
[    1.856181] clk: Disabling unused clocks
[    1.860381] PM: genpd: Disabling unused power domains
[    1.865614] check access for rdinit=/init failed: -2, ignoring
[    1.871490] mtk-pcie-gen3 11280000.pcie: set MEM trans window[0]: cpu_addr = 0x20000000, pci_addr = 0x20000000, size = 0x10000000
[    1.883434] mtk-pcie-gen3 11280000.pcie: PCI host bridge to bus 0000:00
[    1.890045] pci_bus 0000:00: root bus resource [bus 00-ff]
[    1.895555] pci_bus 0000:00: root bus resource [mem 0x20000000-0x2fffffff]
[    1.902443] pci_bus 0000:00: scanning bus
[    1.906470] pci 0000:00:00.0: [14c3:1f32] type 01 class 0x060400 PCIe Root Port
[    1.913799] pci 0000:00:00.0: BAR 0 [mem 0x00000000-0x00007fff 64bit]
[    1.920239] pci 0000:00:00.0: PCI bridge to [bus 00]
[    1.925196] pci 0000:00:00.0:   bridge window [io  0x0000-0x0fff]
[    1.931284] pci 0000:00:00.0:   bridge window [mem 0x00000000-0x000fffff]
[    1.938065] pci 0000:00:00.0:   bridge window [mem 0x00000000-0x000fffff 64bit pref]
[    1.945848] pci 0000:00:00.0: PME# supported from D0 D3hot D3cold
[    1.951938] pci 0000:00:00.0: PME# disabled
[    1.957174] pci_bus 0000:00: fixups for bus
[    1.961372] pci 0000:00:00.0: scanning [bus 00-00] behind bridge, pass 0
[    1.968061] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    1.976070] pci 0000:00:00.0: scanning [bus 00-00] behind bridge, pass 1
[    1.982853] pci_bus 0000:01: scanning bus
[    1.986887] pci 0000:01:00.0: [16c3:abcd] type 00 class 0x0d8000 PCIe Endpoint
[    1.994165] pci 0000:01:00.0: BAR 0 [mem 0x00000000-0x03ffffff pref]
[    2.000523] pci 0000:01:00.0: BAR 1 [mem 0x00000000-0x0000ffff]
[    2.006434] pci 0000:01:00.0: BAR 2 [mem 0x00000000-0x01ffffff pref]
[    2.012785] pci 0000:01:00.0: BAR 3 [mem 0x00000000-0x0000ffff]
[    2.018696] pci 0000:01:00.0: BAR 4 [mem 0x00000000-0x000fffff]
[    2.024612] pci 0000:01:00.0: BAR 5 [mem 0x00000000-0x0000ffff]
[    2.030641] pci 0000:01:00.0: supports D1
[    2.034640] pci 0000:01:00.0: PME# supported from D0 D1 D3hot D3cold
[    2.040991] pci 0000:01:00.0: PME# disabled
[    2.060228] pci 0000:01:00.0: ASPM: default states L0s L1
[    2.065649] pci_bus 0000:01: fixups for bus
[    2.069821] pci_bus 0000:01: bus scan returning with max=01
[    2.075403] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[    2.082037] pci_bus 0000:00: bus scan returning with max=01
[    2.087612] pci 0000:00:00.0: bridge window [mem 0x20000000-0x261fffff]: assigned
[    2.095093] pci 0000:00:00.0: BAR 0 [mem 0x26200000-0x26207fff 64bit]: assigned
[    2.102405] pci 0000:01:00.0: BAR 0 [mem 0x20000000-0x23ffffff pref]: assigned
[    2.109619] pci 0000:01:00.0: BAR 2 [mem 0x24000000-0x25ffffff pref]: assigned
[    2.116837] pci 0000:01:00.0: BAR 4 [mem 0x26000000-0x260fffff]: assigned
[    2.123625] pci 0000:01:00.0: BAR 1 [mem 0x26100000-0x2610ffff]: assigned
[    2.130409] pci 0000:01:00.0: BAR 3 [mem 0x26110000-0x2611ffff]: assigned
[    2.137189] pci 0000:01:00.0: BAR 5 [mem 0x26120000-0x2612ffff]: assigned
[    2.143974] pci 0000:00:00.0: PCI bridge to [bus 01]
[    2.148930] pci 0000:00:00.0:   bridge window [mem 0x20000000-0x261fffff]
[    2.155714] pci_bus 0000:00: resource 4 [mem 0x20000000-0x2fffffff]
[    2.161974] pci_bus 0000:01: resource 1 [mem 0x20000000-0x261fffff]
[    2.168254] pci 0000:00:00.0: save config 0x00: 0x1f3214c3
[    2.173734] pci 0000:00:00.0: save config 0x04: 0x00100000
[    2.179208] pci 0000:00:00.0: save config 0x08: 0x06040001
[    2.184691] pci 0000:00:00.0: save config 0x0c: 0x00010000
[    2.190165] pci 0000:00:00.0: save config 0x10: 0x26200004
[    2.195644] pci 0000:00:00.0: save config 0x14: 0x00000000
[    2.201123] pci 0000:00:00.0: save config 0x18: 0x00010100
[    2.206597] pci 0000:00:00.0: save config 0x1c: 0x000001f1
[    2.212075] pci 0000:00:00.0: save config 0x20: 0x26102000
[    2.217549] pci 0000:00:00.0: save config 0x24: 0x0001fff1
[    2.223027] pci 0000:00:00.0: save config 0x28: 0x00000000
[    2.228502] pci 0000:00:00.0: save config 0x2c: 0x00000000
[    2.233979] pci 0000:00:00.0: save config 0x30: 0x00000000
[    2.239453] pci 0000:00:00.0: save config 0x34: 0x00000080
[    2.244935] pci 0000:00:00.0: save config 0x38: 0x00000000
[    2.250415] pci 0000:00:00.0: save config 0x3c: 0x00020100
[    2.256026] pcieport 0000:00:00.0: assign IRQ: got 81
[    2.261079] pcieport 0000:00:00.0: enabling device (0000 -> 0002)
[    2.267168] pcieport 0000:00:00.0: enabling bus mastering
[    2.273186] mtk-pcie-gen3 11280000.pcie: msi#0x0 address_hi 0x0 address_lo 0x11280c00 data 0
[    2.281629] mtk-pcie-gen3 11280000.pcie: msi#0x1 address_hi 0x0 address_lo 0x11280c00 data 1
[    2.290055] mtk-pcie-gen3 11280000.pcie: msi#0x2 address_hi 0x0 address_lo 0x11280c00 data 2
[    2.298484] mtk-pcie-gen3 11280000.pcie: msi#0x3 address_hi 0x0 address_lo 0x11280c00 data 3
[    2.306921] mtk-pcie-gen3 11280000.pcie: msi#0x4 address_hi 0x0 address_lo 0x11280c00 data 4
[    2.315351] mtk-pcie-gen3 11280000.pcie: msi#0x5 address_hi 0x0 address_lo 0x11280c00 data 5
[    2.323780] mtk-pcie-gen3 11280000.pcie: msi#0x6 address_hi 0x0 address_lo 0x11280c00 data 6
[    2.332209] mtk-pcie-gen3 11280000.pcie: msi#0x7 address_hi 0x0 address_lo 0x11280c00 data 7
[    2.340638] mtk-pcie-gen3 11280000.pcie: msi#0x8 address_hi 0x0 address_lo 0x11280c00 data 8
[    2.349063] mtk-pcie-gen3 11280000.pcie: msi#0x9 address_hi 0x0 address_lo 0x11280c00 data 9
[    2.357492] mtk-pcie-gen3 11280000.pcie: msi#0xa address_hi 0x0 address_lo 0x11280c00 data 10
[    2.366011] mtk-pcie-gen3 11280000.pcie: msi#0xb address_hi 0x0 address_lo 0x11280c00 data 11
[    2.374528] mtk-pcie-gen3 11280000.pcie: msi#0xc address_hi 0x0 address_lo 0x11280c00 data 12
[    2.383044] mtk-pcie-gen3 11280000.pcie: msi#0xd address_hi 0x0 address_lo 0x11280c00 data 13
[    2.391559] mtk-pcie-gen3 11280000.pcie: msi#0xe address_hi 0x0 address_lo 0x11280c00 data 14
[    2.400071] mtk-pcie-gen3 11280000.pcie: msi#0xf address_hi 0x0 address_lo 0x11280c00 data 15
[    2.408588] mtk-pcie-gen3 11280000.pcie: msi#0x10 address_hi 0x0 address_lo 0x11280c00 data 16
[    2.417191] mtk-pcie-gen3 11280000.pcie: msi#0x11 address_hi 0x0 address_lo 0x11280c00 data 17
[    2.425796] mtk-pcie-gen3 11280000.pcie: msi#0x12 address_hi 0x0 address_lo 0x11280c00 data 18
[    2.434399] mtk-pcie-gen3 11280000.pcie: msi#0x13 address_hi 0x0 address_lo 0x11280c00 data 19
[    2.443001] mtk-pcie-gen3 11280000.pcie: msi#0x14 address_hi 0x0 address_lo 0x11280c00 data 20
[    2.451604] mtk-pcie-gen3 11280000.pcie: msi#0x15 address_hi 0x0 address_lo 0x11280c00 data 21
[    2.460207] mtk-pcie-gen3 11280000.pcie: msi#0x16 address_hi 0x0 address_lo 0x11280c00 data 22
[    2.468806] mtk-pcie-gen3 11280000.pcie: msi#0x17 address_hi 0x0 address_lo 0x11280c00 data 23
[    2.477408] mtk-pcie-gen3 11280000.pcie: msi#0x18 address_hi 0x0 address_lo 0x11280c00 data 24
[    2.486013] mtk-pcie-gen3 11280000.pcie: msi#0x19 address_hi 0x0 address_lo 0x11280c00 data 25
[    2.494616] mtk-pcie-gen3 11280000.pcie: msi#0x1a address_hi 0x0 address_lo 0x11280c00 data 26
[    2.503219] mtk-pcie-gen3 11280000.pcie: msi#0x1b address_hi 0x0 address_lo 0x11280c00 data 27
[    2.511823] mtk-pcie-gen3 11280000.pcie: msi#0x1c address_hi 0x0 address_lo 0x11280c00 data 28
[    2.520425] mtk-pcie-gen3 11280000.pcie: msi#0x1d address_hi 0x0 address_lo 0x11280c00 data 29
[    2.529024] mtk-pcie-gen3 11280000.pcie: msi#0x1e address_hi 0x0 address_lo 0x11280c00 data 30
[    2.537626] mtk-pcie-gen3 11280000.pcie: msi#0x1f address_hi 0x0 address_lo 0x11280c00 data 31
[    2.546901] mtk-pcie-gen3 11280000.pcie: msi#0x0 address_hi 0x0 address_lo 0x11280c00 data 0
[    2.555469] pcieport 0000:00:00.0: PME: Signaling with IRQ 82
[    2.561478] pcieport 0000:00:00.0: AER: enabled with IRQ 82
[    2.567191] pcieport 0000:00:00.0: bwctrl: enabled with IRQ 82
[    2.573076] pcieport 0000:00:00.0: save config 0x00: 0x1f3214c3
[    2.578987] pcieport 0000:00:00.0: save config 0x04: 0x00100406
[    2.584911] pcieport 0000:00:00.0: save config 0x08: 0x06040001
[    2.590830] pcieport 0000:00:00.0: save config 0x0c: 0x00010000
[    2.596739] pcieport 0000:00:00.0: save config 0x10: 0x26200004
[    2.602653] pcieport 0000:00:00.0: save config 0x14: 0x00000000
[    2.608561] pcieport 0000:00:00.0: save config 0x18: 0x00010100
[    2.614478] pcieport 0000:00:00.0: save config 0x1c: 0x000001f1
[    2.620392] pcieport 0000:00:00.0: save config 0x20: 0x26102000
[    2.626299] pcieport 0000:00:00.0: save config 0x24: 0x0001fff1
[    2.632213] pcieport 0000:00:00.0: save config 0x28: 0x00000000
[    2.638122] pcieport 0000:00:00.0: save config 0x2c: 0x00000000
[    2.644036] pcieport 0000:00:00.0: save config 0x30: 0x00000000
[    2.649944] pcieport 0000:00:00.0: save config 0x34: 0x00000080
[    2.655860] pcieport 0000:00:00.0: save config 0x38: 0x00000000
[    2.661774] pcieport 0000:00:00.0: save config 0x3c: 0x00020151
[    2.667794] pci 0000:01:00.0: save config 0x00: 0xabcd16c3
[    2.673288] pci 0000:01:00.0: save config 0x04: 0x00110000
[    2.678764] pci 0000:01:00.0: save config 0x08: 0x0d800001
[    2.684246] pci 0000:01:00.0: save config 0x0c: 0x00000000
[    2.689721] pci 0000:01:00.0: save config 0x10: 0x20000008
[    2.695201] pci 0000:01:00.0: save config 0x14: 0x26100000
[    2.700682] pci 0000:01:00.0: save config 0x18: 0x24000008
[    2.706157] pci 0000:01:00.0: save config 0x1c: 0x26110000
[    2.711652] pci 0000:01:00.0: save config 0x20: 0x26000000
[    2.717127] pci 0000:01:00.0: save config 0x24: 0x26120000
[    2.722608] pci 0000:01:00.0: save config 0x28: 0x00000000
[    2.728083] pci 0000:01:00.0: save config 0x2c: 0x00000000
[    2.733565] pci 0000:01:00.0: save config 0x30: 0x00000000
[    2.739040] pci 0000:01:00.0: save config 0x34: 0x00000040
[    2.744520] pci 0000:01:00.0: save config 0x38: 0x00000000
[    2.749995] pci 0000:01:00.0: save config 0x3c: 0x000001ff
[    2.760799] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[    2.768343] Freeing unused kernel memory: 960K
[    2.772877] Run /sbin/init as init process
[    2.776965]   with arguments:
[    2.779920]     /sbin/init
[    2.782637]   with environment:
[    2.785767]     HOME=/
[    2.788115]     TERM=linux
[    3.073660] init: Console is alive
[    3.077185] init: - watchdog -
[    3.532889] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    3.573050] usbcore: registered new interface driver usbfs
[    3.578576] usbcore: registered new interface driver hub
[    3.583948] usbcore: registered new device driver usb
[    3.590326] gpio_button_hotplug: loading out-of-tree module taints kernel.
[    3.603775] xhci-mtk 11200000.usb: supply vbus not found, using dummy regulator
[    3.611660] debugfs: 'type' already exists in 'phy-soc:usb-phy@11e10000.1'
[    3.618538] debugfs: 'efuse' already exists in 'phy-soc:usb-phy@11e10000.1'
[    3.625513] debugfs: 'intr' already exists in 'phy-soc:usb-phy@11e10000.1'
[    3.632386] debugfs: 'tx-imp' already exists in 'phy-soc:usb-phy@11e10000.1'
[    3.639421] debugfs: 'rx-imp' already exists in 'phy-soc:usb-phy@11e10000.1'
[    3.646709] xhci-mtk 11200000.usb: xHCI Host Controller
[    3.651969] xhci-mtk 11200000.usb: new USB bus registered, assigned bus number 1
[    3.662365] xhci-mtk 11200000.usb: hcc params 0x01403f99 hci version 0x110 quirks 0x0000000000200010
[    3.671534] xhci-mtk 11200000.usb: irq 83, io mem 0x11200000
[    3.677299] xhci-mtk 11200000.usb: xHCI Host Controller
[    3.682529] xhci-mtk 11200000.usb: new USB bus registered, assigned bus number 2
[    3.689919] xhci-mtk 11200000.usb: Host supports USB 3.2 Enhanced SuperSpeed
[    3.697388] hub 1-0:1.0: USB hub found
[    3.701185] hub 1-0:1.0: 1 port detected
[    3.705433] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[    3.713896] hub 2-0:1.0: USB hub found
[    3.717667] hub 2-0:1.0: 1 port detected
[    3.729382] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    3.748223] init: - preinit -
[    3.770452] pcieport 0000:00:00.0: AER: Uncorrectable (Fatal) error message received from 0000:00:00.0
[    3.779768] pcieport 0000:00:00.0: PCIe Bus Error: severity=Uncorrectable (Fatal), type=Transaction Layer, (Receiver ID)
[    3.790653] pcieport 0000:00:00.0:   device [14c3:1f32] error status/mask=00000020/00400000
[    3.798999] pcieport 0000:00:00.0:    [ 5] SDES                   (First)
[    3.805784] pcieport 0000:00:00.0: AER: broadcast error_detected message
[    3.812476] pci 0000:01:00.0: AER: can't recover (no error_detected callback)
[    3.830258] pcieport 0000:00:00.0: waiting 100 ms for downstream link
[    3.989491] pci 0000:01:00.0: ready 0ms after bus reset
[    3.994748] pcieport 0000:00:00.0: AER: Root Port link has been reset (0)
[    4.001605] pcieport 0000:00:00.0: AER: device recovery failed
[    4.185322] mtk_soc_eth 15100000.ethernet eth0: configuring for fixed/2500base-x link mode
[    4.193928] mtk_soc_eth 15100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx
[    4.228582] mt7530-mdio mdio-bus:1f lan1: configuring for phy/gmii link mode
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    4.992969] mt7530-mdio mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control rx/tx
[    8.430471] UBIFS (ubi0:2): default file-system created
[    8.436145] UBIFS (ubi0:2): Mounting in unauthenticated mode
[    8.441907] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" started, PID 743
[    8.491962] UBIFS (ubi0:2): UBIFS: mounted UBI device 0, volume 2, name "rootfs_data"
[    8.499794] UBIFS (ubi0:2): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    8.509726] UBIFS (ubi0:2): FS size: 49520640 bytes (47 MiB, 390 LEBs), max 400 LEBs, journal size 2539520 bytes (2 MiB, 20 LEBs)
[    8.521379] UBIFS (ubi0:2): reserved for root: 2338982 bytes (2284 KiB)
[    8.527982] UBIFS (ubi0:2): media format: w5/r0 (latest is w5/r0), UUID D97B9005-25BF-4E43-A8F5-1ECAE48E6E40, small LPT model
[    8.540819] mount_root: overlay filesystem has not been fully initialized yet
[    8.548159] mount_root: switching to ubifs overlay
[    8.555723] overlayfs: null uuid detected in lower fs '/', falling back to xino=off,index=off,nfs_export=off.
[    8.567559] urandom-seed: Seed file not found (/etc/urandom.seed)
[    8.642255] mt7530-mdio mdio-bus:1f lan1: Link is Down
[    8.652623] procd: - early -
[    8.655561] procd: - watchdog -
[    9.201555] procd: - watchdog -
[    9.206412] procd: - ubus -
[    9.282894] procd: - init -
Please press Enter to activate this console.
[    9.667055] kmodloader: loading kernel modules from /etc/modules.d/*
[    9.715985] crypto-safexcel 10320000.crypto: EIP97:230(0,1,4,4)-HIA:270(0,5,5),PE:150/433(alg:7fcdfc00)/0/0/0
[    9.740600] usbcore: registered new interface driver cdc_wdm
[    9.747072] Loading modules backported from Linux version v6.18.26-0-g1fe060681
[    9.754415] Backport generated by backports.git 6ecbb44
[    9.769839] usbcore: registered new interface driver usbserial_generic
[    9.776431] usbserial: USB Serial support registered for generic
[    9.783916] usbcore: registered new interface driver cdc_ether
[    9.791175] usbcore: registered new interface driver cdc_ncm
[    9.811329] usbcore: registered new interface driver huawei_cdc_ncm
[    9.839806] urngd: v1.0.2 started.
[   10.324954] mt798x-wmac 18000000.wifi: HW/SW Version: 0x8a108a10, Build Time: 20240823161240a
[   10.509805] mt798x-wmac 18000000.wifi: WM Firmware Version: ____000000, Build Time: 20240823161304
[   10.607148] mt798x-wmac 18000000.wifi: WA Firmware Version: DEV_000000, Build Time: 20240823161841
[   10.735555] PPP generic driver version 2.4.2
[   10.741153] NET: Registered PF_PPPOX protocol family
[   10.748665] usbcore: registered new interface driver qmi_wwan
[   10.755994] usbcore: registered new interface driver rndis_host
[   10.764776] usbcore: registered new interface driver cdc_mbim
[   10.776149] usbcore: registered new interface driver option
[   10.781869] usbserial: USB Serial support registered for GSM modem (1-port)
[   10.792898] usbcore: registered new interface driver qcserial
[   10.798709] usbserial: USB Serial support registered for Qualcomm USB modem
[   10.806470] kmodloader: done loading kernel modules from /etc/modules.d/*
[   13.730259] usb 1-1: new high-speed USB device number 2 using xhci-mtk
[   13.921419] rndis_host 1-1:1.0 usb0: register 'rndis_host' at usb-11200000.usb-1, RNDIS device, 92:01:b3:e3:cc:69
[   13.937280] option 1-1:1.2: GSM modem (1-port) converter detected
[   13.943634] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0
[   13.950771] option 1-1:1.3: GSM modem (1-port) converter detected
[   13.957050] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1
[   13.964211] option 1-1:1.4: GSM modem (1-port) converter detected
[   13.970576] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB2
[   13.977731] option 1-1:1.5: GSM modem (1-port) converter detected
[   13.984111] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB3
[   13.992382] option 1-1:1.6: GSM modem (1-port) converter detected
[   13.998710] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB4
[   17.632121] mtk_soc_eth 15100000.ethernet eth0: Link is Down
[   17.651124] mtk_soc_eth 15100000.ethernet eth0: configuring for fixed/2500base-x link mode
[   17.663395] mtk_soc_eth 15100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx
[   17.670178] mt7530-mdio mdio-bus:1f lan1: configuring for phy/gmii link mode
[   17.686110] br-lan: port 1(lan1) entered blocking state
[   17.691386] br-lan: port 1(lan1) entered disabled state
[   17.696642] mt7530-mdio mdio-bus:1f lan1: entered allmulticast mode
[   17.702966] mtk_soc_eth 15100000.ethernet eth0: entered allmulticast mode
[   17.714349] mt7530-mdio mdio-bus:1f lan1: entered promiscuous mode
[   18.222717] mt7530-mdio mdio-bus:1f wan: configuring for phy/gmii link mode
[   20.827745] mt7530-mdio mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control rx/tx
[   20.835693] br-lan: port 1(lan1) entered blocking state
[   20.840920] br-lan: port 1(lan1) entered forwarding state
[  108.076855] mt7530-mdio mdio-bus:1f lan1: Link is Down
[  108.082043] br-lan: port 1(lan1) entered disabled state

Zostały ledy, porty w luci i muszę sprawdzić czy powrót do oryginalnego oprogramowania działa i czy sysupgrade przez soft przejściowy działa. Cezary, będę potrzebował pomocy z ledami. Tak mam je zdefiniowane teraz:

leds {
        compatible = "gpio-leds";

        led_status: status {
            function = LED_FUNCTION_STATUS;
            color = <LED_COLOR_ID_GREEN>;
            gpios = <&pio 2 GPIO_ACTIVE_HIGH>;
        };

        wifi {
            function = LED_FUNCTION_WLAN;
            color = <LED_COLOR_ID_GREEN>;
            gpios = <&pio 13 GPIO_ACTIVE_HIGH>;
        };

        blue {
            color = <LED_COLOR_ID_BLUE>;
            gpios = <&pio 14 GPIO_ACTIVE_HIGH>;
        };

        yellow {
            label = "oem:green:yellow";
            gpios = <&pio 15 GPIO_ACTIVE_HIGH>;
        };

        red {
            label = "oem:green:red";
            gpios = <&pio 26 GPIO_ACTIVE_HIGH>;
        };

        signal-low {
            color = <LED_COLOR_ID_RED>;
            gpios = <&pio 27 GPIO_ACTIVE_HIGH>;
        };

        signal-mid {
            color = <LED_COLOR_ID_YELLOW>;
            gpios = <&pio 28 GPIO_ACTIVE_HIGH>;
        };

        signal-high {
            color = <LED_COLOR_ID_WHITE>;
            gpios = <&pio 30 GPIO_ACTIVE_LOW>;
        };

GPIO są dobrze dodane, tylko teraz je poprawnie zdefiniować.

lukasz3134 · 2026-05-09 10:28:06

lukasz3134
Użytkownik
Nieaktywny

Skąd: Tomaszów Mazowiecki
Zarejestrowany: 2025-05-22
Posty: 270

Odp: Cudy P2 5G v1.0 - wsparcie OpenWRT

Sysupgrade przez soft przejściowy cudy nie działa. Wywala błąd image verification check failed. Więc na razie zostaje konsola.

Cezary · 2026-05-09 11:02:04

Cezary
...
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2006-02-25
Posty: 116,153

Odp: Cudy P2 5G v1.0 - wsparcie OpenWRT

Urządzenie się nie zgadza? To wtedy do supported musisz dodać nazwę.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

lukasz3134 · 2026-05-09 11:04:16

lukasz3134
Użytkownik
Nieaktywny

Skąd: Tomaszów Mazowiecki
Zarejestrowany: 2025-05-22
Posty: 270

Odp: Cudy P2 5G v1.0 - wsparcie OpenWRT

Do makefile ? Mam tak:

define Device/cudy_p2-5g
  DEVICE_VENDOR := Cudy
  DEVICE_MODEL := P2 5G
  DEVICE_VARIANT := v1
  DEVICE_DTS := mt7981b-cudy-p2-5g
  DEVICE_DTS_DIR := ../dts
  SUPPORTED_DEVICES += R91
  UBINIZE_OPTS := -E 5
  BLOCKSIZE := 128k
  PAGESIZE := 2048
  IMAGE_SIZE := 65536k
  KERNEL_IN_UBI := 1
  KERNEL := kernel-bin | lzma | \
    fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
  KERNEL_INITRAMFS := kernel-bin | lzma | \
    fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k
  IMAGES := sysupgrade.bin
  IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
  DEVICE_PACKAGES := kmod-mt7915e kmod-mt7981-firmware mt7981-wo-firmware
endef
TARGET_DEVICES += cudy_p2-5g

lukasz3134 · 2026-05-09 11:59:56

lukasz3134
Użytkownik
Nieaktywny

Skąd: Tomaszów Mazowiecki
Zarejestrowany: 2025-05-22
Posty: 270

Odp: Cudy P2 5G v1.0 - wsparcie OpenWRT

To się nie nacieszyłem internetem mobilnym przez modem. Modem pracuję tylko w trybie NCM i nie da się go przełączyć na inny tryb. Jak próbuję się połączyć to mam comgt error: could not write to the device. Peszek...

lukasz3134 · 2026-05-09 15:53:16

lukasz3134
Użytkownik
Nieaktywny

Skąd: Tomaszów Mazowiecki
Zarejestrowany: 2025-05-22
Posty: 270

Odp: Cudy P2 5G v1.0 - wsparcie OpenWRT

Ok, na razie odpusczam temat tego routera. Modem pracuje w trybie ncm i nie da się go przełączyć w inny tryb. Ciekawostka jest taka, że widać go jako usb0, ale jak wyłączy się w DTS node pcie, to modem jest niewidoczny, bo siedzi na USB a USB jest podłączone pod mostek PCI. Dodatkowo w logu mam pełno błędów AER Uncorrectable error message received i modem pojawia się i znika. Jak ktoś chciałby pociągnąć temat dalej, to jest to możliwe, a całe info jest w tym wątku.

lukasz3134 · 2026-05-10 13:07:44

lukasz3134
Użytkownik
Nieaktywny

Skąd: Tomaszów Mazowiecki
Zarejestrowany: 2025-05-22
Posty: 270

Odp: Cudy P2 5G v1.0 - wsparcie OpenWRT

Na czystym openwrt mam problemy z tym modemem co siedzi w tym routerze. Pojawia się i znika co kiladziesiąt sekund. Na pewno to nie jest wina zasilania, bo na sofcie Cudy działa wszystko w porządku i używam tego samego zasilacza. Tak się przedstawia na usb:

T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  4 Spd=480  MxCh= 0
D:  Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=2c7c ProdID=0900 Rev= 4.04
S:  Manufacturer=Quectel
S:  Product=RG500U-EB
S:  SerialNumber=0123456789ABCDEF
C:* #Ifs= 7 Cfg#= 1 Atr=c0 MxPwr=500mA
A:  FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=03
I:* If#= 0 Alt= 0 #EPs= 1 Cls=e0(wlcon) Sub=01 Prot=03 Driver=(none)
E:  Ad=82(I) Atr=03(Int.) MxPS=   8 Ivl=32ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=(none)
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms

Używa sterownika rndis_host, tu go usunąłem, bo myślałem że to coś pomoże. Chyba muszę wrócić do softu Cudy albo coś innego jest jeszcze nie tak.

lukasz3134 · 2026-05-11 05:11:56

lukasz3134
Użytkownik
Nieaktywny

Skąd: Tomaszów Mazowiecki
Zarejestrowany: 2025-05-22
Posty: 270

Odp: Cudy P2 5G v1.0 - wsparcie OpenWRT

Postęp z modemem, a mianowicie działa. Wszystkie błędy i rozłączania to wina zbyt dużej ilości sterowników w obrazie. Modem jest widoczny jako usb0, ale łączność jest na ttyUSB2. Ciągle działa tylko w trybie rndis i żadnym innym.

EDIT: Modem działa tylko przez luci-proto-3g, prędkości rzędu 10 megabitów na sekundę, port ttyUSB2 jest odpowiedzialny za łączenie się z siecią ale to jest też port komunikacyjny, więc nie odczytamy żadnych danych. Wygląda na to że modem nie obsługuję innych trybów poza rndis. Ogólnie, porażka, gra nie warta świeczki, spodziewałem się znacznie więcej. Składam go do kupy i wgrywam soft Cudy.

Cezary · 2026-05-11 06:02:38

Cezary
...
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2006-02-25
Posty: 116,153

Odp: Cudy P2 5G v1.0 - wsparcie OpenWRT

Jak masz rndis to prawodopodobnie jaką kombinacją AT jesteś w stanie aktywować połączenie, później dhcp na tym i normalnie masz internet. Tylko znajdź jakie to polecenia AT...

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

lukasz3134 · 2026-05-11 06:06:03

lukasz3134
Użytkownik
Nieaktywny

Skąd: Tomaszów Mazowiecki
Zarejestrowany: 2025-05-22
Posty: 270

Odp: Cudy P2 5G v1.0 - wsparcie OpenWRT

No właśnie haczyk w tym że nie mogę. AT+QCFG="usbnet" pokazuje mi, że możliwe jest 1,2,3,5,11,13,15. Próbowałem wszystkie i on nadal jest w trybie rndis. Nie przełącza się w żaden inny tryb.

IceG · 2026-05-11 06:28:22

IceG
Użytkownik
Nieaktywny

Skąd: Radom
Zarejestrowany: 2014-08-14
Posty: 1,428

Odp: Cudy P2 5G v1.0 - wsparcie OpenWRT

Tu chyba bardziej chodzilo o polecenia podnoszace polaczenie, a nie przestawiajace modem, cos w stylu..

ip link set usb0 up
udhcpc -i usb0

Używasz moich pakietów/obrazów z github?
Chcesz abym dalej je rozwijał i tworzył nowe?
Postaw kawę

Cezary · 2026-05-11 06:49:22

Cezary
...
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2006-02-25
Posty: 116,153

Odp: Cudy P2 5G v1.0 - wsparcie OpenWRT

Dokładnie, i wcześniej jakaś aktywacja kontekstu połączenia, ustawienia apn to pewnie standardowo.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

lukasz3134 · 2026-05-11 07:43:01

lukasz3134
Użytkownik
Nieaktywny

Skąd: Tomaszów Mazowiecki
Zarejestrowany: 2025-05-22
Posty: 270

Odp: Cudy P2 5G v1.0 - wsparcie OpenWRT

Ustawienia apn były prawidłowe, adres ip był przyznawany bo sprawdzłem poleceniem AT+CGPADDR. Używałem DHCP, ale nie było ruchu w ogóle.

frutis · 2026-05-11 08:20:01

frutis
Użytkownik
Nieaktywny

Zarejestrowany: 2009-11-10
Posty: 1,698

Odp: Cudy P2 5G v1.0 - wsparcie OpenWRT

lukasz3134 napisał/a:

No właśnie haczyk w tym że nie mogę. AT+QCFG="usbnet" pokazuje mi, że możliwe jest 1,2,3,5,11,13,15. Próbowałem wszystkie i on nadal jest w trybie rndis. Nie przełącza się w żaden inny tryb.

A te zmiany zapisują się czy cały czas jest 3? Po zmianie wołałeś AT+CFUN=1,1?

lukasz3134 · 2026-05-11 08:31:21

lukasz3134
Użytkownik
Nieaktywny

Skąd: Tomaszów Mazowiecki
Zarejestrowany: 2025-05-22
Posty: 270

Odp: Cudy P2 5G v1.0 - wsparcie OpenWRT

Zmiany się zapisują, po wpisaniu AT+QCFG="usbnet", widzę że cyfry się zmieniają, ale nie zmiena się tryb działania modemu. Cały czas jest przypisywany sterownik rndis host. Tak w ogóle, to ten modem ma soc unisoc a nie qualcomm, dlatego może nie być tam np. mbim.

frutis · 2026-05-11 08:57:52

frutis
Użytkownik
Nieaktywny

Zarejestrowany: 2009-11-10
Posty: 1,698

Odp: Cudy P2 5G v1.0 - wsparcie OpenWRT

W oprogramowaniu od Cudy jest taki skrypt który coś robi z modemem:
- /etc/pcie_check_1

#!/bin/sh /etc/rc.common
# Copyright (C) 2006 OpenWrt.org
. /lib/functions/leds.sh

#gcom start is 38
START=39

led_blink_upgrade() {
    filename1="oem:green:blue"
    filename2="oem:green:wifi"
    led_timer $filename1 100 100
    led_timer $filename2 100 100
}

boot() {
    # Rx500U PCIe模式: 0 - EP模式；1 - RC模式
    local retries=0
    local raw_result=""

    # 首次读取模式会出错 CME ERROR: 4，尝试 3 次
    while [ $retries -lt 3 ]; do
        raw_result=$(ubus call network.gcom at '{"device":"/dev/ttyUSB2", "cmd":"AT+QCFG=\"pcie/mode\""}')
        if [ -n "$raw_result" ] && ! echo "$raw_result" | grep -q "ERROR"; then
            break
        fi
        retries=$((retries + 1))
        echo "pcie: try read pcie mode ${retries} times" > /dev/console
        # echo "pcie: raw_result=$raw_result" > /dev/console
        sleep 1
    done

    local pcie_mode=$(echo "$raw_result" | grep ',1')

    [ -n "$pcie_mode" ] && {
        local set_pcie_mode=$(ubus call network.gcom at '{"device":"/dev/ttyUSB2", "cmd":"AT+QCFG=\"pcie/mode\",0"}')
        sleep 1

        [  x"$(bdinfo factory)" = x1 ] && {
            led_blink_upgrade
        }

        local result=$(ubus call network.gcom at '{"device":"/dev/ttyUSB2", "cmd":"AT+QCFG=\"pcie/mode\""}' | grep ',0')
        [ -n "$result" ] && {    
            [  x"$(bdinfo factory)" != x1 ] && {
                echo "set 5G module from PCIe RC mode to EP mode success. Reboot system" > /dev/console
                reboot
                return
            }
        }
    }

    # 卸载usb驱动，避免模块重启，usb disconnect导致死机
    rmmod option
    echo "pcie: rmmod option driver" > /dev/console

    [ ! -f "/etc/no_check_pcie" -a x"$(bdinfo factory)" != x1 ] && { 
        local pcie_ok=$(lspci)         
        local bdinfo_ok=$(bdinfo list)

        [ -f "/etc/init.d/pcie_check_2" ] && rm /etc/init.d/pcie_check_2

        [ -n "$bdinfo_ok" -a -z "$pcie_ok" ] && {
            [ ! -f "/etc/pcie_error" ] && {
                touch /etc/pcie_error
                echo 0 > /etc/pcie_error
            }
            local pcie_error=$(cat /etc/pcie_error)
            pcie_error=$(($pcie_error+1))
            echo $pcie_error > /etc/pcie_error
            [ $pcie_error -le 2 ] && {
                echo "enumerate pcie error! check1 count=$pcie_error . Reboot system" > /dev/console
                sync
                reboot
                return
            }
            [ $pcie_error -ge 3 ] && {
                echo "enumerate pcie error! check1 count=$pcie_error . remove flag" > /dev/console
                rm /etc/pcie_error
            }
        }
        [ -n "$bdinfo_ok" -a -n "$pcie_ok" ] && {
            [ -f "/etc/pcie_error" ] && rm /etc/pcie_error
        }                       
    } 
}

A taką konfigurację ma ten modem:

        2c7c:900 )
            uci set network.${IFACE}.proto='dhcp'
            uci set network.${IFACE}.ifname="pcie0"
            uci set network.${IFACE}.service='all'
            uci set network.${IFACE}.cdevice="/dev/stty_nr31"
            uci set network.${IFACE}.vendor='quectel-5g'
            uci set network.${IFACE}.pcimode="0"
            uci set network.${IFACE}.i18name='5G'
            uci set network.${IFACE}6.i18name='5G6'

Cezary · 2026-05-11 09:40:12

Cezary
...
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2006-02-25
Posty: 116,153

Odp: Cudy P2 5G v1.0 - wsparcie OpenWRT

Ty masz ten sam modem co w xunison którego IceG męczymy.

Jak na moje to ten skrypt sprawdza czy jest modem , jak nie to robi rescan magistrali PCI i tyle.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

lukasz3134 · 2026-05-11 09:54:30

lukasz3134
Użytkownik
Nieaktywny

Skąd: Tomaszów Mazowiecki
Zarejestrowany: 2025-05-22
Posty: 270

Odp: Cudy P2 5G v1.0 - wsparcie OpenWRT

To nie jest ten sam modem. W xunisonie jest RM500Q-AE na m.2, u mnie jest RG500U-EB na LGA czyli wlutowany w płytę główną. Ten /dev/stty_nr31 to od sterownika quectel sprd-pcie. Z kompilowania tego na kernel 6.12 wyszła kupa. Jak zrobię AT+QCFG="data_interface" to mam CME:ERROR 4.

frutis · 2026-05-11 10:24:52

frutis
Użytkownik
Nieaktywny

Zarejestrowany: 2009-11-10
Posty: 1,698

Odp: Cudy P2 5G v1.0 - wsparcie OpenWRT

W configu kernel'a jest: CONFIG_PCIE_SPRD=y a w logach

[    0.846635] sprd_pci_ep_dev_init Quectel_Linux&Android_SPRD_PCIE_Driver_V1.1.8

.
Czyli ten modem działa po pci?

Dawno temu ktoś dodawał wsparcie ale nie weszło to: https://patchwork.kernel.org/project/li … mp;state=*

lukasz3134 · 2026-05-11 10:29:12

lukasz3134
Użytkownik
Nieaktywny

Skąd: Tomaszów Mazowiecki
Zarejestrowany: 2025-05-22
Posty: 270

Odp: Cudy P2 5G v1.0 - wsparcie OpenWRT

Z loga systemowego cudy wynika że podłączany jest właśnie sprd-pci i dodatkowo rndis-host.

Wed May  6 18:36:23 2026 kern.info kernel: [    0.846635] sprd_pci_ep_dev_init Quectel_Linux&Android_SPRD_PCIE_Driver_V1.1.8
Wed May  6 18:36:23 2026 kern.info kernel: [    0.854087] sipc: name=sprd,sipc
Wed May  6 18:36:23 2026 kern.info kernel: [    0.857332] sipc: type=1
Wed May  6 18:36:23 2026 kern.info kernel: [    0.859868] sipc: dst =1
Wed May  6 18:36:23 2026 kern.info kernel: [    0.862411] sipc: ep_dev=0
Wed May  6 18:36:23 2026 kern.info kernel: [    0.865127] sipc: smem_type = 0
Wed May  6 18:36:23 2026 kern.info kernel: [    0.869224] sipc: smem_base=0x4e000000, dst_smem_base=0x4e000000, smem_size=0x300000
Wed May  6 18:36:23 2026 kern.info kernel: [    0.877009] sipc: high_offset=0x0n
Wed May  6 18:36:23 2026 kern.info kernel: [    0.877012] smsg_ipc_create: sprd,sipc
Wed May  6 18:36:23 2026 kern.info kernel: [    0.884290] smem_init: pool addr = 0x4e000000, size = 0x300000 added.
Wed May  6 18:36:23 2026 kern.info kernel: [    0.890769] smsg_ipc_smem_init: ring_base = 0x4e000000, ring_size = 0x1000
Wed May  6 18:36:23 2026 kern.debug kernel: [    0.897997] spipe_probe!
Wed May  6 18:36:23 2026 kern.debug kernel: [    0.900551] spipe: after parse device tree, name=spipe_nr, dst=1, channel=4, ringnr=15,  rxbuf_size=0x1000, txbuf_size=0x1000
Wed May  6 18:36:23 2026 kern.info kernel: [    0.911920] sbuf_host_init: channel 1-4, offset = 0x0!
Wed May  6 18:36:23 2026 kern.info kernel: [    0.917216] smsg_ch_open: channel 1-4 send open msg!
Wed May  6 18:36:23 2026 kern.debug kernel: [    0.917668] spipe_probe!
Wed May  6 18:36:23 2026 kern.info kernel: [    0.922246] pcie res: request resource, state=0.
Wed May  6 18:36:23 2026 kern.debug kernel: [    0.924778] spipe: after parse device tree, name=sdiag_nr, dst=1, channel=21, ringnr=1,  rxbuf_size=0x8000, txbuf_size=0x40000
Wed May  6 18:36:23 2026 kern.info kernel: [    0.940858] sbuf_host_init: channel 1-21, offset = 0x0!
Wed May  6 18:36:23 2026 kern.debug kernel: [    0.946328] spipe_probe!
Wed May  6 18:36:23 2026 kern.debug kernel: [    0.948890] spipe: after parse device tree, name=stty_nr, dst=1, channel=6, ringnr=32,  rxbuf_size=0x800, txbuf_size=0x800
Wed May  6 18:36:23 2026 kern.info kernel: [    0.959998] sbuf_host_init: channel 1-6, offset = 0x0!
Wed May  6 18:36:23 2026 kern.info kernel: [    0.965292] smsg_ch_open: channel 1-21 send open msg!
Wed May  6 18:36:23 2026 kern.debug kernel: [    0.969287] spipe_probe!
Wed May  6 18:36:23 2026 kern.debug kernel: [    0.972935] spipe: after parse device tree, name=snv_nr, dst=1, channel=40, ringnr=1,  rxbuf_size=0x1000, txbuf_size=0x40400
Wed May  6 18:36:23 2026 kern.info kernel: [    0.984219] sbuf_host_init: channel 1-40, offset = 0x0!
Wed May  6 18:36:23 2026 kern.info kernel: [    0.989518] smsg_ch_open: channel 1-6 send open msg!
Wed May  6 18:36:23 2026 kern.info kernel: [    0.989783] spool: name=slog_nr, dst=1, channel=5, pre_cfg=0
Wed May  6 18:36:23 2026 kern.info kernel: [    1.000215] spool: tx_num=0, tx_size=0, rx_num=32, rx_size=65536
Wed May  6 18:36:23 2026 kern.info kernel: [    1.006337] smsg_ch_open: channel 1-40 send open msg!
Wed May  6 18:36:23 2026 kern.debug kernel: [    1.008612] sprd-pcie-ep-device 0001:01:00.0: assign IRQ: got 91
Wed May  6 18:36:23 2026 kern.info kernel: [    1.017472] sprd-pcie-ep-device 0001:01:00.0: ep: probe
Wed May  6 18:36:23 2026 kern.info kernel: [    1.022736] pci 0001:00:00.0: enabling device (0000 -> 0002)
Wed May  6 18:36:23 2026 kern.debug kernel: [    1.028427] pci 0001:00:00.0: enabling bus mastering
Wed May  6 18:36:23 2026 kern.info kernel: [    1.033418] sprd-pcie-ep-device 0001:01:00.0: enabling device (0000 -> 0002)
Wed May  6 18:36:23 2026 kern.debug kernel: [    1.040516] sprd-pcie-ep-device 0001:01:00.0: enabling bus mastering
Wed May  6 18:36:23 2026 kern.info kernel: [    1.046905] sprd-pcie-ep-device 0001:01:00.0: ep: BAR[0] [mem 0x20000000-0x203fffff pref]
Wed May  6 18:36:23 2026 kern.info kernel: [    1.055125] sprd-pcie-ep-device 0001:01:00.0: ep: BAR[1] [mem 0x20c00000-0x20c0ffff]
Wed May  6 18:36:23 2026 kern.info kernel: [    1.062907] sprd-pcie-ep-device 0001:01:00.0: ep: BAR[2] [mem 0x20400000-0x207fffff pref]
Wed May  6 18:36:23 2026 kern.info kernel: [    1.071127] sprd-pcie-ep-device 0001:01:00.0: ep: BAR[3] [mem 0x20c10000-0x20c1ffff]
Wed May  6 18:36:23 2026 kern.info kernel: [    1.078909] sprd-pcie-ep-device 0001:01:00.0: ep: BAR[4] [mem 0x20800000-0x20bfffff]
Wed May  6 18:36:23 2026 kern.info kernel: [    1.086692] sprd-pcie-ep-device 0001:01:00.0: ep: BAR[5] [mem 0x20c20000-0x20c2ffff]
Wed May  6 18:36:23 2026 kern.info kernel: [    1.094484] sprd-pcie-ep-device 0001:01:00.0: ep: atu_view_port val = 0xffffffff
Wed May  6 18:36:23 2026 kern.info kernel: [    1.101921] sprd-pcie-ep-device 0001:01:00.0: ep: failed to get MSI, err=-22, irq=91
Wed May  6 18:36:23 2026 kern.err kernel: [    1.109703] sprd_ep_map_memory: get bar = 2
Wed May  6 18:36:23 2026 kern.info kernel: [    1.114134] comfifo0 tx_fifo addr-0xffffffc011fcd000
Wed May  6 18:36:23 2026 kern.info kernel: [    1.119168] comfifo0 rx_fifo addr-0xffffffc011fde000
Wed May  6 18:36:23 2026 kern.info kernel: [    1.124198] comfifo1 tx_fifo addr-0xffffffc011fef000
Wed May  6 18:36:23 2026 kern.info kernel: [    1.129228] comfifo1 rx_fifo addr-0xffffffc012801000
Wed May  6 18:36:23 2026 kern.info kernel: [    1.134254] virt_sipa virt_sipa: fifo_id = 0 rx_fifo depth = 0x1000
Wed May  6 18:36:23 2026 kern.info kernel: [    1.145967] smsg_ch_open: channel 1-5 send open msg!
Wed May  6 18:36:23 2026 kern.info kernel: [    1.146036] virt_sipa virt_sipa: sender create start
Wed May  6 18:36:23 2026 kern.info kernel: [    1.151018] smem_get_area: addr = 0x4e000000, size = 0x300000.
Wed May  6 18:36:23 2026 kern.err kernel: [    1.156163] sipa_sender_ck_unfree: need wait remote_ready!
Wed May  6 18:36:23 2026 kern.info kernel: [    1.161830] sprd-pcie-ep-device 0001:01:00.0: pass_smem, base=0x4e000000,size=0x300000
Wed May  6 18:36:23 2026 kern.err kernel: [    1.167337] sipa_sender_ck_unfree: need wait remote_ready!
Wed May  6 18:36:23 2026 kern.info kernel: [    1.175291] pcie res: ep_notify, probed cnt=1.

Wed May  6 18:36:23 2026 kern.info kernel: [   20.179801] rndis_host 1-1:1.0 usb0: register 'rndis_host' at usb-11200000.xhci-1, RNDIS device, 3e:ba:bf:0d:18:ce
Wed May  6 18:36:23 2026 kern.info kernel: [   20.194428] extif_put_dev(ra0)
Wed May  6 18:36:23 2026 kern.info kernel: [   20.195128] option 1-1:1.2: GSM modem (1-port) converter detected
Wed May  6 18:36:23 2026 kern.info kernel: [   20.197497] mtk_ppe_dev_unregister_hook : ineterface ra0 set null (1)
Wed May  6 18:36:23 2026 kern.info kernel: [   20.210210] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0
Wed May  6 18:36:23 2026 kern.info kernel: [   20.217299] option 1-1:1.3: GSM modem (1-port) converter detected
Wed May  6 18:36:23 2026 kern.info kernel: [   20.223571] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1
Wed May  6 18:36:23 2026 kern.info kernel: [   20.230669] option 1-1:1.4: GSM modem (1-port) converter detected
Wed May  6 18:36:23 2026 kern.info kernel: [   20.236968] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB2
Wed May  6 18:36:23 2026 kern.info kernel: [   20.244107] option 1-1:1.5: GSM modem (1-port) converter detected
Wed May  6 18:36:23 2026 kern.info kernel: [   20.250400] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB3
Wed May  6 18:36:23 2026 kern.info kernel: [   20.257543] option 1-1:1.6: GSM modem (1-port) converter detected
Wed May  6 18:36:23 2026 kern.info kernel: [   20.263857] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB4

frutis · 2026-05-11 10:37:47

frutis
Użytkownik
Nieaktywny

Zarejestrowany: 2009-11-10
Posty: 1,698

Odp: Cudy P2 5G v1.0 - wsparcie OpenWRT

Tutaj są jakieś nowe sterowniki: https://github.com/Quectel-Pi/Pi-H1-Lin … /sprd_pcie

lukasz3134 · 2026-05-11 10:40:27

lukasz3134
Użytkownik
Nieaktywny

Skąd: Tomaszów Mazowiecki
Zarejestrowany: 2025-05-22
Posty: 270

Odp: Cudy P2 5G v1.0 - wsparcie OpenWRT

Spróbuję to później skompilować.

FAQ o OpenWrt | Sprzedam różne routery | Oddam

Cudy P2 5G v1.0 - wsparcie OpenWRT (Strona 3 z 4)

Posty: 51 do 75 z 92

51 Odpowiedź przez lukasz3134 2026-05-09 09:03:00

Odp: Cudy P2 5G v1.0 - wsparcie OpenWRT

52 Odpowiedź przez lukasz3134 2026-05-09 09:17:27

Odp: Cudy P2 5G v1.0 - wsparcie OpenWRT

53 Odpowiedź przez lukasz3134 2026-05-09 09:40:01 (edytowany przez lukasz3134 2026-05-09 09:41:39)

Odp: Cudy P2 5G v1.0 - wsparcie OpenWRT

54 Odpowiedź przez lukasz3134 2026-05-09 10:02:32 (edytowany przez lukasz3134 2026-05-09 10:03:07)

Odp: Cudy P2 5G v1.0 - wsparcie OpenWRT

55 Odpowiedź przez lukasz3134 2026-05-09 10:28:06

Odp: Cudy P2 5G v1.0 - wsparcie OpenWRT

56 Odpowiedź przez Cezary 2026-05-09 11:02:04

Odp: Cudy P2 5G v1.0 - wsparcie OpenWRT

57 Odpowiedź przez lukasz3134 2026-05-09 11:04:16

Odp: Cudy P2 5G v1.0 - wsparcie OpenWRT

58 Odpowiedź przez lukasz3134 2026-05-09 11:59:56

Odp: Cudy P2 5G v1.0 - wsparcie OpenWRT

59 Odpowiedź przez lukasz3134 2026-05-09 15:53:16

Odp: Cudy P2 5G v1.0 - wsparcie OpenWRT

60 Odpowiedź przez lukasz3134 2026-05-10 13:07:44

Odp: Cudy P2 5G v1.0 - wsparcie OpenWRT

61 Odpowiedź przez lukasz3134 2026-05-11 05:11:56 (edytowany przez lukasz3134 2026-05-11 05:27:29)

Odp: Cudy P2 5G v1.0 - wsparcie OpenWRT

62 Odpowiedź przez Cezary 2026-05-11 06:02:38

Odp: Cudy P2 5G v1.0 - wsparcie OpenWRT

63 Odpowiedź przez lukasz3134 2026-05-11 06:06:03

Odp: Cudy P2 5G v1.0 - wsparcie OpenWRT

64 Odpowiedź przez IceG 2026-05-11 06:28:22

Odp: Cudy P2 5G v1.0 - wsparcie OpenWRT

65 Odpowiedź przez Cezary 2026-05-11 06:49:22

Odp: Cudy P2 5G v1.0 - wsparcie OpenWRT

66 Odpowiedź przez lukasz3134 2026-05-11 07:43:01

Odp: Cudy P2 5G v1.0 - wsparcie OpenWRT

67 Odpowiedź przez frutis 2026-05-11 08:20:01

Odp: Cudy P2 5G v1.0 - wsparcie OpenWRT

68 Odpowiedź przez lukasz3134 2026-05-11 08:31:21

Odp: Cudy P2 5G v1.0 - wsparcie OpenWRT

69 Odpowiedź przez frutis 2026-05-11 08:57:52 (edytowany przez frutis 2026-05-11 09:12:02)

Odp: Cudy P2 5G v1.0 - wsparcie OpenWRT

70 Odpowiedź przez Cezary 2026-05-11 09:40:12

Odp: Cudy P2 5G v1.0 - wsparcie OpenWRT

71 Odpowiedź przez lukasz3134 2026-05-11 09:54:30 (edytowany przez lukasz3134 2026-05-11 09:55:05)

Odp: Cudy P2 5G v1.0 - wsparcie OpenWRT

72 Odpowiedź przez frutis 2026-05-11 10:24:52

Odp: Cudy P2 5G v1.0 - wsparcie OpenWRT

73 Odpowiedź przez lukasz3134 2026-05-11 10:29:12 (edytowany przez lukasz3134 2026-05-11 10:32:39)

Odp: Cudy P2 5G v1.0 - wsparcie OpenWRT

74 Odpowiedź przez frutis 2026-05-11 10:37:47

Odp: Cudy P2 5G v1.0 - wsparcie OpenWRT

75 Odpowiedź przez lukasz3134 2026-05-11 10:40:27

Odp: Cudy P2 5G v1.0 - wsparcie OpenWRT

Posty: 51 do 75 z 92