Temat: TOTOLINK X6000R
Witam,
kupiłem wczoraj takie cudo TOTOLINK X6000R
Czy po przez stronę www mogę mu wrzucić OpenWrt ?
Pytam, wiem, że macie sporą wiedzę na ten temat.
Nie jesteś zalogowany. Proszę się zalogować lub zarejestrować.
eko.one.pl → Sprzęt / Hardware → TOTOLINK X6000R
Zaloguj się lub zarejestruj by napisać odpowiedź
Witam,
kupiłem wczoraj takie cudo TOTOLINK X6000R
Czy po przez stronę www mogę mu wrzucić OpenWrt ?
Pytam, wiem, że macie sporą wiedzę na ten temat.
Witam,
kupiłem wczoraj takie cudo TOTOLINK X6000R
Czy po przez stronę www mogę mu wrzucić OpenWrt ?
Pytam, wiem, że macie sporą wiedzę na ten temat.
no przez oryginalny soft wrzucasz openwrt
https://openwrt.org/toh/totolink/x6000r?s[]=procd
https://git.openwrt.org/openwrt/openwrt … 3b12eeb822
Dzięki za odpowiedź ..
Mogę to robić w ten sposób : ?
Browse to http://192.168.1.1/Upgrade.asp
Upload .bin file to router
Wait for it to reboot
Telnet to 192.168.1.1 and set a root password, or browse to http://192.168.1.1 if LuCI is installed.
Czy konieczne jest trzymanie przycisku Reset przy uruchamianiu Routera , i dopiero późniejsza instalacja pliku KERNEL ?
No musisz przez reset, inaczej nie będzie tej strony.
Tak więc udał się flash OpenWrt X6000R.
W razie czego -
W sklepie na 'x' mają fajną obniżkę ceny tego Totolinka - 60 zł taniej.
Tak więc udał się flash OpenWrt X6000R.
W razie czego -
W sklepie na 'x' mają fajną obniżkę ceny tego Totolinka - 60 zł taniej.
W normalnej cenie czyli powyżej 200 zł kompletnie moim zdaniem się nie opłaca, za 160 już prędzej ale nadal czy ja wiem
Za tyle jest np WR3000P na promocji który ma 2x tyle ramu i USB które może się przydać
Jakiś czas temu w normalnej cenie totolinka (te 200-220) był zyxel T-56(EX5601-T0/T1) który zjada jego na śniadanie, lecz chyba bezpowrotnie te czasy minęły...
WR3000P Sprawia mi wiecej problemow, jak bezobsługowy dla mnie xiaomi ax3000t (jeszcze na 23.x). Pisalem o tym w odpowiednim watku.
Czekam na ustabilizowanie sie 25.x i zobacze, czy jest lepiej.
Dlaczego w opcji :
Maximum transmit power
Mam tylko -
0 dBm (1 mW) - Current power: 0 dBm
nie mogę tego zwiększyć,
czemu tak się dzieje .
Może wybrałeś nieobsługiwany kanał?
U mnie się tak dzieje, gdy wybiorę kanał wyższy niż 128.
Co może oznaczać, że kanał jest nieobsługiwany .
Spróbowałem prawie wszystkich kanałów, nie mogę zwiększyć wartości:
Maximum transmit power
Czy nowy firmware może poprawić tą funkcję ?
Mam kilka Routerów, na żadnym nie mam takiego 'błędu'.
Pokaż wyniki iw list
Tego jest sporo, jak to wrzucić ?
Jak pokazać w formie najbardziej bezpiecznej .?
Po prostu wklej jako tekst. Nie tam nic wrażliwego żebyś musiał to robić "bezpiecznie"
root@OpenWrt:~# iw list
Wiphy phy1
wiphy index: 1
max # scan SSIDs: 4
max scan IEs length: 2190 bytes
max # sched scan SSIDs: 0
max # match sets: 0
Retry short limit: 7
Retry long limit: 4
Coverage class: 0 (up to 0m)
Device supports AP-side u-APSD.
Device supports T-DLS.
Available Antennas: TX 0x3 RX 0x3
Configured Antennas: TX 0x1c RX 0x1c
Supported interface modes:
* IBSS
* managed
* AP
* AP/VLAN
* monitor
* mesh point
* P2P-client
* P2P-GO
Band 2:
Capabilities: 0x9ff
RX LDPC
HT20/HT40
SM Power Save disabled
RX Greenfield
RX HT20 SGI
RX HT40 SGI
TX STBC
RX STBC 1-stream
Max AMSDU length: 7935 bytes
No DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 2 usec (0x04)
HT TX/RX MCS rate indexes supported: 0-15
VHT Capabilities (0x339a59f6):
Max MPDU length: 11454
Supported Channel Width: 160 MHz
RX LDPC
short GI (80 MHz)
short GI (160/80+80 MHz)
TX STBC
SU Beamformer
SU Beamformee
MU Beamformer
MU Beamformee
RX antenna pattern consistency
TX antenna pattern consistency
VHT RX MCS set:
1 streams: MCS 0-9
2 streams: MCS 0-9
3 streams: not supported
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
VHT RX highest supported: 0 Mbps
VHT TX MCS set:
1 streams: MCS 0-9
2 streams: MCS 0-9
3 streams: not supported
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
VHT TX highest supported: 0 Mbps
VHT extended NSS: supported
HE Iftypes: managed
HE MAC Capabilities (0x08011a000040):
+HTC HE Supported
Trigger Frame MAC Padding Duration: 2
OM Control
Maximum A-MPDU Length Exponent: 3
A-MSDU in A-MPDU
HE PHY Capabilities: (0x4c704e926d12f3164e3f00):
HE40/HE80/5GHz
HE160/5GHz
242 tone RUs/5GHz
Device Class: 1
LDPC Coding in Payload
HE SU PPDU with 1x HE-LTF and 0.8us GI
NDP with 4x HE-LTF and 3.2us GI
STBC Tx <= 80MHz
STBC Rx <= 80MHz
Full Bandwidth UL MU-MIMO
DCM Max Constellation: 2
DCM Max Constellation Rx: 2
SU Beamformer
SU Beamformee
Beamformee STS <= 80MHz: 3
Beamformee STS > 80MHz: 3
Sounding Dimensions <= 80MHz: 2
Sounding Dimensions > 80MHz: 2
Codebook Size SU Feedback
Codebook Size MU Feedback
Triggered CQI Feedback
Partial Bandwidth Extended Range
Partial Bandwidth DL MU-MIMO
PPE Threshold Present
Power Boost Factor ar
HE SU PPDU & HE PPDU 4x HE-LTF 0.8us GI
Max NC: 2
20MHz in 40MHz HE PPDU 2.4GHz
20MHz in 160/80+80MHz HE PPDU
80MHz in 160/80+80MHz HE PPDU
DCM Max BW: 1
Longer Than 16HE SIG-B OFDM Symbols
Non-Triggered CQI Feedback
TX 1024-QAM
RX 1024-QAM
RX Full BW SU Using HE MU PPDU with Compression SIGB
RX Full BW SU Using HE MU PPDU with Non-Compression SIGB
HE RX MCS and NSS set <= 80 MHz
1 streams: MCS 0-11
2 streams: MCS 0-11
3 streams: not supported
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
HE TX MCS and NSS set <= 80 MHz
1 streams: MCS 0-11
2 streams: MCS 0-11
3 streams: not supported
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
HE RX MCS and NSS set 160 MHz
1 streams: MCS 0-11
2 streams: MCS 0-11
3 streams: not supported
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
HE TX MCS and NSS set 160 MHz
1 streams: MCS 0-11
2 streams: MCS 0-11
3 streams: not supported
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
PPE Threshold 0x79 0x1c 0xc7 0x71 0x1c 0xc7 0x71
HE Iftypes: AP
HE MAC Capabilities (0x00051a081044):
+HTC HE Supported
TWT Responder
BSR
OM Control
Maximum A-MPDU Length Exponent: 3
BQR
A-MSDU in A-MPDU
OM Control UL MU Data Disable RX
HE PHY Capabilities: (0x0c204e926f12afd0000c00):
HE40/HE80/5GHz
HE160/5GHz
LDPC Coding in Payload
NDP with 4x HE-LTF and 3.2us GI
STBC Tx <= 80MHz
STBC Rx <= 80MHz
Full Bandwidth UL MU-MIMO
DCM Max Constellation: 2
DCM Max Constellation Rx: 2
SU Beamformer
SU Beamformee
MU Beamformer
Beamformee STS <= 80MHz: 3
Beamformee STS > 80MHz: 3
Sounding Dimensions <= 80MHz: 2
Sounding Dimensions > 80MHz: 2
Codebook Size SU Feedback
Codebook Size MU Feedback
Triggered SU Beamforming Feedback
Triggered MU Beamforming Feedback
Partial Bandwidth Extended Range
PPE Threshold Present
Max NC: 2
STBC Tx > 80MHz
STBC Rx > 80MHz
TX 1024-QAM
RX 1024-QAM
HE RX MCS and NSS set <= 80 MHz
1 streams: MCS 0-11
2 streams: MCS 0-11
3 streams: not supported
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
HE TX MCS and NSS set <= 80 MHz
1 streams: MCS 0-11
2 streams: MCS 0-11
3 streams: not supported
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
HE RX MCS and NSS set 160 MHz
1 streams: MCS 0-11
2 streams: MCS 0-11
3 streams: not supported
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
HE TX MCS and NSS set 160 MHz
1 streams: MCS 0-11
2 streams: MCS 0-11
3 streams: not supported
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
PPE Threshold 0x79 0x1c 0xc7 0x71 0x1c 0xc7 0x71
HE Iftypes: mesh point
HE MAC Capabilities (0x00011a000040):
+HTC HE Supported
OM Control
Maximum A-MPDU Length Exponent: 3
A-MSDU in A-MPDU
HE PHY Capabilities: (0x0c200c0000000000008000):
HE40/HE80/5GHz
HE160/5GHz
LDPC Coding in Payload
STBC Tx <= 80MHz
STBC Rx <= 80MHz
HE RX MCS and NSS set <= 80 MHz
1 streams: MCS 0-11
2 streams: MCS 0-11
3 streams: not supported
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
HE TX MCS and NSS set <= 80 MHz
1 streams: MCS 0-11
2 streams: MCS 0-11
3 streams: not supported
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
HE RX MCS and NSS set 160 MHz
1 streams: MCS 0-11
2 streams: MCS 0-11
3 streams: not supported
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
HE TX MCS and NSS set 160 MHz
1 streams: MCS 0-11
2 streams: MCS 0-11
3 streams: not supported
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
Frequencies:
* 5180.0 MHz [36] (0.0 dBm)
* 5200.0 MHz [40] (0.0 dBm)
* 5220.0 MHz [44] (0.0 dBm)
* 5240.0 MHz [48] (0.0 dBm)
* 5260.0 MHz [52] (0.0 dBm) (no IR, radar detection)
* 5280.0 MHz [56] (0.0 dBm) (no IR, radar detection)
* 5300.0 MHz [60] (0.0 dBm) (no IR, radar detection)
* 5320.0 MHz [64] (0.0 dBm) (no IR, radar detection)
* 5500.0 MHz [100] (0.0 dBm) (no IR, radar detection)
* 5520.0 MHz [104] (0.0 dBm) (no IR, radar detection)
* 5540.0 MHz [108] (0.0 dBm) (no IR, radar detection)
* 5560.0 MHz [112] (0.0 dBm) (no IR, radar detection)
* 5580.0 MHz [116] (0.0 dBm) (no IR, radar detection)
* 5600.0 MHz [120] (0.0 dBm) (no IR, radar detection)
* 5620.0 MHz [124] (0.0 dBm) (no IR, radar detection)
* 5640.0 MHz [128] (0.0 dBm) (no IR, radar detection)
* 5660.0 MHz [132] (0.0 dBm) (no IR, radar detection)
* 5680.0 MHz [136] (0.0 dBm) (no IR, radar detection)
* 5700.0 MHz [140] (0.0 dBm) (no IR, radar detection)
* 5720.0 MHz [144] (0.0 dBm) (no IR, radar detection)
* 5745.0 MHz [149] (0.0 dBm) (no IR)
* 5765.0 MHz [153] (0.0 dBm) (no IR)
* 5785.0 MHz [157] (0.0 dBm) (no IR)
* 5805.0 MHz [161] (0.0 dBm) (no IR)
* 5825.0 MHz [165] (0.0 dBm) (no IR)
* 5845.0 MHz [169] (disabled)
* 5865.0 MHz [173] (disabled)
* 5885.0 MHz [177] (disabled)
valid interface combinations:
* #{ IBSS } <= 1, #{ AP, mesh point } <= 16, #{ managed } <= 19,
total <= 19, #channels <= 1, STA/AP BI must match, radar detect widths: { 20 MHz (no HT), 20 MHz, 40 MHz, 80 MHz, 160 MHz }
HT Capability overrides:
* MCS: ff ff ff ff ff ff ff ff ff ff
* maximum A-MSDU length
* supported channel width
* short GI for 40 MHz
* max A-MPDU length exponent
* min MPDU start spacing
max # scan plans: 1
max scan plan interval: -1
max scan plan iterations: 0
Supported extended features:
* [ VHT_IBSS ]: VHT-IBSS
* [ RRM ]: RRM
* [ BEACON_RATE_LEGACY ]: legacy beacon rate setting
* [ BEACON_RATE_HT ]: HT beacon rate setting
* [ BEACON_RATE_VHT ]: VHT beacon rate setting
* [ FILS_STA ]: STA FILS (Fast Initial Link Setup)
* [ CQM_RSSI_LIST ]: multiple CQM_RSSI_THOLD records
* [ CONTROL_PORT_OVER_NL80211 ]: control port over nl80211
* [ ACK_SIGNAL_SUPPORT ]: ack signal level support
* [ TXQS ]: FQ-CoDel-enabled intermediate TXQs
* [ SCAN_RANDOM_SN ]: use random sequence numbers in scans
* [ SCAN_MIN_PREQ_CONTENT ]: use probe request with only rate IEs in scans
* [ CAN_REPLACE_PTK0 ]: can safely replace PTK 0 when rekeying
* [ AIRTIME_FAIRNESS ]: airtime fairness scheduling
* [ STA_TX_PWR ]: TX power control per station
* [ AQL ]: Airtime Queue Limits (AQL)
* [ CONTROL_PORT_NO_PREAUTH ]: disable pre-auth over nl80211 control port support
* [ DEL_IBSS_STA ]: deletion of IBSS station support
* [ SCAN_FREQ_KHZ ]: scan on kHz frequency support
* [ CONTROL_PORT_OVER_NL80211_TX_STATUS ]: tx status for nl80211 control port support
* [ FILS_DISCOVERY ]: FILS discovery frame transmission support
* [ UNSOL_BCAST_PROBE_RESP ]: unsolicated broadcast probe response transmission support
* [ BEACON_RATE_HE ]: HE beacon rate support (AP/mesh)
* [ BSS_COLOR ]: BSS coloring support
* [ POWERED_ADDR_CHANGE ]: can change MAC address while up
Wiphy phy0
wiphy index: 0
max # scan SSIDs: 4
max scan IEs length: 2200 bytes
max # sched scan SSIDs: 0
max # match sets: 0
Retry short limit: 7
Retry long limit: 4
Coverage class: 0 (up to 0m)
Device supports AP-side u-APSD.
Device supports T-DLS.
Available Antennas: TX 0x3 RX 0x3
Configured Antennas: TX 0x3 RX 0x3
Supported interface modes:
* IBSS
* managed
* AP
* AP/VLAN
* monitor
* mesh point
* P2P-client
* P2P-GO
Band 1:
Capabilities: 0x9ff
RX LDPC
HT20/HT40
SM Power Save disabled
RX Greenfield
RX HT20 SGI
RX HT40 SGI
TX STBC
RX STBC 1-stream
Max AMSDU length: 7935 bytes
No DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 2 usec (0x04)
HT TX/RX MCS rate indexes supported: 0-15
HE Iftypes: managed
HE MAC Capabilities (0x08011a000040):
+HTC HE Supported
Trigger Frame MAC Padding Duration: 2
OM Control
Maximum A-MPDU Length Exponent: 3
A-MSDU in A-MPDU
HE PHY Capabilities: (0x22704e926d09f30e4e3f00):
HE40/2.4GHz
242 tone RUs/2.4GHz
Device Class: 1
LDPC Coding in Payload
HE SU PPDU with 1x HE-LTF and 0.8us GI
NDP with 4x HE-LTF and 3.2us GI
STBC Tx <= 80MHz
STBC Rx <= 80MHz
Full Bandwidth UL MU-MIMO
DCM Max Constellation: 2
DCM Max Constellation Rx: 2
SU Beamformer
SU Beamformee
Beamformee STS <= 80MHz: 3
Beamformee STS > 80MHz: 3
Sounding Dimensions <= 80MHz: 1
Sounding Dimensions > 80MHz: 1
Codebook Size SU Feedback
Codebook Size MU Feedback
Triggered CQI Feedback
Partial Bandwidth Extended Range
Partial Bandwidth DL MU-MIMO
PPE Threshold Present
Power Boost Factor ar
HE SU PPDU & HE PPDU 4x HE-LTF 0.8us GI
Max NC: 1
20MHz in 40MHz HE PPDU 2.4GHz
20MHz in 160/80+80MHz HE PPDU
80MHz in 160/80+80MHz HE PPDU
DCM Max BW: 1
Longer Than 16HE SIG-B OFDM Symbols
Non-Triggered CQI Feedback
TX 1024-QAM
RX 1024-QAM
RX Full BW SU Using HE MU PPDU with Compression SIGB
RX Full BW SU Using HE MU PPDU with Non-Compression SIGB
HE RX MCS and NSS set <= 80 MHz
1 streams: MCS 0-11
2 streams: MCS 0-11
3 streams: not supported
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
HE TX MCS and NSS set <= 80 MHz
1 streams: MCS 0-11
2 streams: MCS 0-11
3 streams: not supported
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
PPE Threshold 0x19 0x1c 0xc7 0x71
HE Iftypes: AP
HE MAC Capabilities (0x00051a081044):
+HTC HE Supported
TWT Responder
BSR
OM Control
Maximum A-MPDU Length Exponent: 3
BQR
A-MSDU in A-MPDU
OM Control UL MU Data Disable RX
HE PHY Capabilities: (0x02204e926f09afc8000c00):
HE40/2.4GHz
LDPC Coding in Payload
NDP with 4x HE-LTF and 3.2us GI
STBC Tx <= 80MHz
STBC Rx <= 80MHz
Full Bandwidth UL MU-MIMO
DCM Max Constellation: 2
DCM Max Constellation Rx: 2
SU Beamformer
SU Beamformee
MU Beamformer
Beamformee STS <= 80MHz: 3
Beamformee STS > 80MHz: 3
Sounding Dimensions <= 80MHz: 1
Sounding Dimensions > 80MHz: 1
Codebook Size SU Feedback
Codebook Size MU Feedback
Triggered SU Beamforming Feedback
Triggered MU Beamforming Feedback
Partial Bandwidth Extended Range
PPE Threshold Present
Max NC: 1
STBC Tx > 80MHz
STBC Rx > 80MHz
TX 1024-QAM
RX 1024-QAM
HE RX MCS and NSS set <= 80 MHz
1 streams: MCS 0-11
2 streams: MCS 0-11
3 streams: not supported
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
HE TX MCS and NSS set <= 80 MHz
1 streams: MCS 0-11
2 streams: MCS 0-11
3 streams: not supported
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
PPE Threshold 0x19 0x1c 0xc7 0x71
HE Iftypes: mesh point
HE MAC Capabilities (0x00011a000040):
+HTC HE Supported
OM Control
Maximum A-MPDU Length Exponent: 3
A-MSDU in A-MPDU
HE PHY Capabilities: (0x02200c0000000000008000):
HE40/2.4GHz
LDPC Coding in Payload
STBC Tx <= 80MHz
STBC Rx <= 80MHz
HE RX MCS and NSS set <= 80 MHz
1 streams: MCS 0-11
2 streams: MCS 0-11
3 streams: not supported
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
HE TX MCS and NSS set <= 80 MHz
1 streams: MCS 0-11
2 streams: MCS 0-11
3 streams: not supported
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
Frequencies:
* 2412.0 MHz [1] (20.0 dBm)
* 2417.0 MHz [2] (20.0 dBm)
* 2422.0 MHz [3] (20.0 dBm)
* 2427.0 MHz [4] (20.0 dBm)
* 2432.0 MHz [5] (20.0 dBm)
* 2437.0 MHz [6] (20.0 dBm)
* 2442.0 MHz [7] (20.0 dBm)
* 2447.0 MHz [8] (20.0 dBm)
* 2452.0 MHz [9] (20.0 dBm)
* 2457.0 MHz [10] (20.0 dBm)
* 2462.0 MHz [11] (20.0 dBm)
* 2467.0 MHz [12] (20.0 dBm) (no IR)
* 2472.0 MHz [13] (20.0 dBm) (no IR)
* 2484.0 MHz [14] (20.0 dBm) (no IR)
valid interface combinations:
* #{ IBSS } <= 1, #{ AP, mesh point } <= 16, #{ managed } <= 19,
total <= 19, #channels <= 1, STA/AP BI must match, radar detect widths: { 20 MHz (no HT), 20 MHz, 40 MHz, 80 MHz, 160 MHz }
HT Capability overrides:
* MCS: ff ff ff ff ff ff ff ff ff ff
* maximum A-MSDU length
* supported channel width
* short GI for 40 MHz
* max A-MPDU length exponent
* min MPDU start spacing
max # scan plans: 1
max scan plan interval: -1
max scan plan iterations: 0
Supported extended features:
* [ VHT_IBSS ]: VHT-IBSS
* [ RRM ]: RRM
* [ BEACON_RATE_LEGACY ]: legacy beacon rate setting
* [ BEACON_RATE_HT ]: HT beacon rate setting
* [ BEACON_RATE_VHT ]: VHT beacon rate setting
* [ FILS_STA ]: STA FILS (Fast Initial Link Setup)
* [ CQM_RSSI_LIST ]: multiple CQM_RSSI_THOLD records
* [ CONTROL_PORT_OVER_NL80211 ]: control port over nl80211
* [ ACK_SIGNAL_SUPPORT ]: ack signal level support
* [ TXQS ]: FQ-CoDel-enabled intermediate TXQs
* [ SCAN_RANDOM_SN ]: use random sequence numbers in scans
* [ SCAN_MIN_PREQ_CONTENT ]: use probe request with only rate IEs in scans
* [ CAN_REPLACE_PTK0 ]: can safely replace PTK 0 when rekeying
* [ AIRTIME_FAIRNESS ]: airtime fairness scheduling
* [ STA_TX_PWR ]: TX power control per station
* [ AQL ]: Airtime Queue Limits (AQL)
* [ CONTROL_PORT_NO_PREAUTH ]: disable pre-auth over nl80211 control port support
* [ DEL_IBSS_STA ]: deletion of IBSS station support
* [ SCAN_FREQ_KHZ ]: scan on kHz frequency support
* [ CONTROL_PORT_OVER_NL80211_TX_STATUS ]: tx status for nl80211 control port support
* [ FILS_DISCOVERY ]: FILS discovery frame transmission support
* [ UNSOL_BCAST_PROBE_RESP ]: unsolicated broadcast probe response transmission support
* [ BEACON_RATE_HE ]: HE beacon rate support (AP/mesh)
* [ BSS_COLOR ]: BSS coloring support
* [ POWERED_ADDR_CHANGE ]: can change MAC address while up
root@OpenWrt:~#
Jak widzisz na poziomie sterownika masz raportowaną moc jako 0.0dBm. Zaktualizuj sobie system do najnowszej wersji stabilnej, jeżeli nadal będzie zero to zgłaszają błąd na openwrt.
Włączony
* 2484.0 MHz [14] (20.0 dBm) (no IR)
więc może coś z ustawieniami kraju (także 5 GHz) jest zepsute (np. dla ustawień Polska ten kanał chyba nie powinien być dostępny).
Zaś
* 5845.0 MHz [169] (disabled)
* 5865.0 MHz [173] (disabled)
powinny być w Polsce dostępne.
iw reg get ci pokaże kraj.
U mnie jest jak poniżej, dla porównania.
Chciałoby się, aby działało 320 MHz dla 6 GHz.
root@AX3000T:/tmp# iw reg get
global
country PL: DFS-ETSI
(2400 - 2483 @ 40), (N/A, 20), (N/A)
(5150 - 5250 @ 80), (N/A, 23), (N/A), NO-OUTDOOR, AUTO-BW
(5250 - 5350 @ 80), (N/A, 20), (0 ms), NO-OUTDOOR, DFS, AUTO-BW
(5470 - 5725 @ 160), (N/A, 26), (0 ms), DFS
(5725 - 5875 @ 80), (N/A, 13), (N/A)
(5945 - 6425 @ 320), (N/A, 23), (N/A), NO-OUTDOOR
(57000 - 66000 @ 2160), (N/A, 40), (N/A)
Czyli zrób aktualizację i dopiero zgłaszaj błędy jeżeli nadal będzie tak samo.
kto mi powie , gdzie się zgłasza tego typu problemy ..
kolejne wydanie : v25.12.4
dalej ten sam problem
Maximum transmit power
- Current power: 0 dBm
Tu: https://github.com/openwrt/openwrt/issues
Czy ktoś z Was posiada 'TOTOLINK X6000R' ?
Czy tylko na mnie to trafiło ?
A byłaby opcja zaaplikowania tego patcha do snapshot?
https://github.com/openwrt/openwrt/pull/21669
Akurat mam ten chip i udało mi się skompilowac czysty openwrt oraz odpalić na nowym chipie, ale wolałbym mimo to wersję EKO, bo używam też na X5000r.
Jeżeli tylko będzie się chciało skompilowac to tak. A czy działa to już ktoś musi sprawdzić kto ma sprzęt z tym chiperm.
jaki sprzęt masz, ten x6000r?
Dokładnie tak, X6000r. Patch sprawdziłem na czystym openwrt i odpala się poprawnie. Chętnie przetestuję i skorzystam ![]()
Był tylko błąd przy aplikowaniu commitu usuwajacego starszy patch, ale to dlatego że ten patch był robiony na kernel 6.16, a teraz jest 6.18, o ile dobrze pamiętam.
Zaloguj się lub zarejestruj by napisać odpowiedź
eko.one.pl → Sprzęt / Hardware → TOTOLINK X6000R
Forum oparte o PunBB, wspierane przez Informer Technologies, Inc