1

Temat: WiFi 5GHz - mediatek <-> qualcomm

Podłączyłem sobie ap ze sta na 5GHz między MT7986 i IPQ8074 i to prawie nie działa:

PING 192.168.1.1 (192.168.1.1): 56 data bytes
64 bytes from 192.168.1.1: seq=0 ttl=64 time=991.361 ms
64 bytes from 192.168.1.1: seq=1 ttl=64 time=195.255 ms
64 bytes from 192.168.1.1: seq=2 ttl=64 time=5004.815 ms
64 bytes from 192.168.1.1: seq=3 ttl=64 time=4004.692 ms
64 bytes from 192.168.1.1: seq=4 ttl=64 time=3004.547 ms
64 bytes from 192.168.1.1: seq=5 ttl=64 time=2004.425 ms
64 bytes from 192.168.1.1: seq=6 ttl=64 time=1004.267 ms
64 bytes from 192.168.1.1: seq=7 ttl=64 time=4.102 ms
64 bytes from 192.168.1.1: seq=8 ttl=64 time=5892.473 ms
64 bytes from 192.168.1.1: seq=9 ttl=64 time=4892.398 ms
64 bytes from 192.168.1.1: seq=10 ttl=64 time=3892.248 ms
64 bytes from 192.168.1.1: seq=11 ttl=64 time=2892.095 ms
64 bytes from 192.168.1.1: seq=12 ttl=64 time=1894.336 ms
64 bytes from 192.168.1.1: seq=13 ttl=64 time=894.217 ms
64 bytes from 192.168.1.1: seq=14 ttl=64 time=607.912 ms

Dodam, że routery stoją obok siebie i po 2,4GHz wszystko działa.

Czy są jakieś specjalne ustawienia w takim przypadku potrzebne? Testuje to na snapshocie.

2

Odp: WiFi 5GHz - mediatek <-> qualcomm

Straszne masz te pingi....

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

3 (edytowany przez frutis 2026-01-22 23:23:51)

Odp: WiFi 5GHz - mediatek <-> qualcomm

Tak to wygląda od strony ap:

Station xx:xx:xx:xx:xx:xx (on phy1-ap0)
    authorized:    yes
    authenticated:    yes
    associated:    yes
    preamble:    long
    WMM/WME:    yes
    MFP:        yes
    TDLS peer:    no
    inactive time:    3380 ms
    rx bytes:    19226
    rx packets:    203
    tx bytes:    19481
    tx packets:    199
    tx retries:    73
    tx failed:    73
    rx drop misc:    16
    signal:      -23 [-28, -31, -33, -25] dBm
    signal avg:    -22 [-28, -30, -33, -24] dBm
    tx bitrate:    864.7 MBit/s 160MHz HE-MCS 3 HE-NSS 3 HE-GI 0 HE-DCM 0
    tx duration:    135492 us
    rx bitrate:    516.0 MBit/s HE-MCS 10 HE-NSS 4 HE-GI 0 HE-DCM 0
    rx duration:    129440 us
    last ack signal:-30 dBm
    avg ack signal:    -33 dBm
    airtime weight: 256
    expected throughput:    717.679Mbps
    DTIM period:    2
    beacon interval:100
    short slot time:yes
    connected time:    211 seconds
    associated at [boottime]:    259722.923s
    associated at:    1769118794543 ms
    current time:    1769119005471 ms

Zauważyłem, że inactive time rośnie do 5 senund mimo, że cały czas pinguję z klienta.

Jest dużo błędów Illegal rate phy:

cat /sys/kernel/debug/ieee80211/phy0/ath11k/fw_stats/pdev_stats 

             ath11k PDEV stats
             =================

           Channel noise floor        -96
              Channel TX power         40
                TX frame count  238464224
                RX frame count  129637206
                RX clear count  406699019
                   Cycle count 2146988113
               PHY error count        135

          ath11k PDEV TX stats
          ====================

            HTT cookies queued          0
             HTT cookies disp.          0
                   MSDU queued       1853
                   MPDU queued       1263
                 MSDUs dropped          0
                  Local enqued         16
                   Local freed         16
                     HW queued    2786789
                  PPDUs reaped    2786788
                 Num underruns          0
                 Num HW Paused          0
                 PPDUs cleaned    2715717
                MPDUs requeued        279
                       PPDU OK        249
             Excessive retries       2048
                       HW rate        954
           Sched self triggers        115
     Dropped due to SW retries        102
       Illegal rate phy errors     106215
        PDEV continuous xretry          0
                    TX timeout          0
                   PDEV resets          6
 Stateless TIDs alloc failures          0
                  PHY underrun          0
  MPDU is more than txop limit          0
          Num sequences posted          0
      Num seq failed queueing           0
      Num sequences completed     2918769
      Num sequences restarted      201993
   Num of MU sequences posted     2716775
      Num of MPDUS SW flushed          38
     Num of MPDUS HW filtered           0
       Num of MPDUS truncated           0
      Num of MPDUS ACK failed           0
         Num of MPDUS expired           0

          ath11k PDEV RX stats
          ====================

         Mid PPDU route change        135
       Tot. number of statuses        135
        Extra frags on rings 0        135
        Extra frags on rings 1        135
        Extra frags on rings 2        135
        Extra frags on rings 3        135
        MSDUs delivered to HTT      12704
        MPDUs delivered to HTT      12433
      MSDUs delivered to stack      17860
      MPDUs delivered to stack      17860
               Oversized AMSUs        135
                    PHY errors        135
              PHY errors drops        135
   MPDU errors (FCS, MIC, ENC)        135
               Overflow errors        135

4

Odp: WiFi 5GHz - mediatek <-> qualcomm

Preamble auto albo short?

Dom : router https://i.imgur.com/IuB6Zwy.png | TP-LINK T1700G-28TQ |Zyxel XGS-1210-12 | 6x Ruckus r310 unleashed  + Ruckus icx7150-c12p | Truenas scale 124TB 25Gb| Xpenology 12TB | apc smart ups 750 lcd smile 100Mb/s - 25Gb/s
Podróżne : GL.Inet MT3000  +1TB hdd
Działka : rb260gs 1j wdm 1Gb+ ruckus r310 + nb m5 + kilka kamer ip  + panel 285Wp + lifepo4 12v 60Ah .

5

Odp: WiFi 5GHz - mediatek <-> qualcomm

Problem występuje tylko dla 160MHz. Czy da się ustawić szerokość dla klienta w OpenWrt?