Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset),  D - Delta,  S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.3.1-00148
S - IMAGE_VARIANT_STRING=HAABANAZA
S - OEM_IMAGE_VERSION_STRING=CRM
S - Boot Config, 0x000002e1
B -       203 - PBL, Start
B -      2740 - bootable_media_detect_entry, Start
B -      2885 - bootable_media_detect_success, Start
B -      2890 - elf_loader_entry, Start
B -     11379 - auth_hash_seg_entry, Start
B -     11621 - auth_hash_seg_exit, Start
B -    250135 - elf_segs_hash_verify_entry, Start
B -    310653 - PBL, End
B -    320494 - SBL1, Start
B -    372344 - GCC [RstStat:0x10, RstDbg:0x600000] WDog Stat : 0x4
B -    378810 - pm_device_init, Start
B -    498431 - PM_SET_VAL:Skip
D -    118889 - pm_device_init, Delta
B -    500688 - pm_driver_init, Start
D -      5337 - pm_driver_init, Delta
B -    507184 - clock_init, Start
D -      2104 - clock_init, Delta
B -    511210 - boot_flash_init, Start
D -      3965 - boot_flash_init, Delta
B -    518927 - boot_config_data_table_init, Start
D -      1006 - boot_config_data_table_init, Delta - (575 Bytes)
B -    528748 - Boot Setting :  0x00000618
B -    532469 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:0,Subtype:8
B -    539392 - sbl1_ddr_set_params, Start
B -    543205 - CPR configuration: 0x30c
B -    546560 - cpr_init, Start
B -    549457 - Rail:0 Mode: 5 Voltage: 792000
B -    554551 - CL CPR settled at 744000mV
B -    557387 - Rail:1 Mode: 5 Voltage: 880000
B -    561657 - Rail:1 Mode: 7 Voltage: 888000
D -     16531 - cpr_init, Delta
B -    568459 - Pre_DDR_clock_init, Start
B -    572576 - Pre_DDR_clock_init, End
B -    575870 - DDR Type : PCDDR3
B -    581604 - do ddr sanity test, Start
D -      1067 - do ddr sanity test, Delta
B -    586362 - DDR: Start of HAL DDR Boot Training
B -    591090 - DDR: End of HAL DDR Boot Training
B -    596763 - DDR: Checksum to be stored on flash is 1317878529
B -    607194 - Image Load, Start
D -    335439 - QSEE Image Loaded, Delta - (1374392 Bytes)
B -    942694 - Image Load, Start
D -        61 - SEC Image Loaded, Delta - (0 Bytes)
B -    950380 - Image Load, Start
D -      9760 - DEVCFG Image Loaded, Delta - (26008 Bytes)
B -    960201 - Image Load, Start
D -     30988 - RPM Image Loaded, Delta - (106428 Bytes)
B -    991280 - Image Load, Start
D -    142252 - APPSBL Image Loaded, Delta - (579192 Bytes)
B -   1133685 - QSEE Execution, Start
D -        61 - QSEE Execution, Delta
B -   1139480 - USB D+ check, Start
D -         0 - USB D+ check, Delta
B -   1145885 - SBL1, End
D -    827678 - SBL1, Delta
S - Flash Throughput, 4430 KB/s  (2087267 Bytes,  471098 us)
S - DDR Frequency, 466 MHz
S - Core 0 Frequency, 1651 MHz


U-Boot 2016.01 (Nov 04 2020 - 16:18:16 +0800)

DRAM:  smem ram ptable found: ver: 1 len: 4
sys led OK!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
1 GiB
NAND:  ONFI device found
ID = 1580a1c2
Vendor = c2
Device = a1
SPI_ADDR_LEN=3
SF: Detected MX25U6435F with page size 256 Bytes, erase size 64 KiB, total 8 MiB
ipq_spi: page_size: 0x100, sector_size: 0x10000, size: 0x800000
136 MiB
MMC:   sdhci: Node Not found, skipping initialization

PCI1 is not defined in the device tree
In:    serial@78B3000
Out:   serial@78B3000
Err:   serial@78B3000
machid: 8010008
MMC Device 0 not found
eth2 MAC Address from ART is not valid
eth3 MAC Address from ART is not valid
eth4 MAC Address from ART is not valid
eth5 MAC Address from ART is not valid
Hit any key to stop autoboot:  0
ubi0: attaching mtd2
ubi0: scanning is finished
ubi0: attached mtd2 (name "mtd=0", size 52 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 416, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 3/1, WL threshold: 4096, image sequence number: 1171331939
ubi0: available PEBs: 0, total reserved PEBs: 416, PEBs reserved for bad PEB handling: 20
Read 0 bytes from volume kernel to 44000000
No size specified -> Using max size (5206016)
## Loading kernel from FIT Image at 44000000 ...
   Using 'config@hk09' configuration
   Trying 'kernel-1' kernel subimage
     Description:  ARM64 OpenWrt Linux-6.6.93
     Type:         Kernel Image
     Compression:  gzip compressed
     Data Start:   0x440000e8
     Data Size:    5136185 Bytes = 4.9 MiB
     Architecture: AArch64
     OS:           Linux
     Load Address: 0x41000000
     Entry Point:  0x41000000
     Hash algo:    crc32
     Hash value:   32d90fd7
     Hash algo:    sha1
     Hash value:   7f9eff7fc88bc74dc5e35e8bd8d2de04048209b2
   Verifying Hash Integrity ... crc32+ sha1+ OK
## Loading fdt from FIT Image at 44000000 ...
   Using 'config@hk09' configuration
   Trying 'fdt-1' fdt subimage
     Description:  ARM64 OpenWrt yuncore_ax880 device tree blob
     Type:         Flat Device Tree
     Compression:  uncompressed
     Data Start:   0x444e6164
     Data Size:    45935 Bytes = 44.9 KiB
     Architecture: AArch64
     Hash algo:    crc32
     Hash value:   c8bbbb1d
     Hash algo:    sha1
     Hash value:   59797fb5d276834e148c6be8e97ef64af9da2d1f
   Verifying Hash Integrity ... crc32+ sha1+ OK
   Booting using the fdt blob at 0x444e6164
   Uncompressing Kernel Image ... OK
   Loading Device Tree to 4a3f1000, end 4a3ff36e ... OK
fdt-fixup: unable to find compatible node
Could not find PCI in device tree
Using machid 0x8010008 from environment

Starting kernel ...

Jumping to AARCH64 kernel via monitor
[    0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[    0.000000] Linux version 6.6.93 (builder@buildhost) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 13.3.0 r28739-d9340319c6) 13.3.0, GNU ld (GNU Binutils) 2.42) #0 SMP Mon Jun 23 20:40:36 2025
[    0.000000] Machine model: Yuncore AX880
[    0.000000] OF: reserved mem: 0x0000000040000000..0x0000000040ffffff (16384 KiB) nomap non-reusable nss@40000000
[    0.000000] OF: reserved mem: 0x000000004a400000..0x000000004a5fffff (2048 KiB) nomap non-reusable tzapp@4a400000
[    0.000000] OF: reserved mem: 0x000000004a600000..0x000000004a9fffff (4096 KiB) nomap non-reusable bootloader@4a600000
[    0.000000] OF: reserved mem: 0x000000004aa00000..0x000000004aafffff (1024 KiB) nomap non-reusable sbl@4aa00000
[    0.000000] OF: reserved mem: 0x000000004ab00000..0x000000004abfffff (1024 KiB) nomap non-reusable smem@4ab00000
[    0.000000] OF: reserved mem: 0x000000004ac00000..0x000000004affffff (4096 KiB) nomap non-reusable memory@4ac00000
[    0.000000] OF: reserved mem: 0x000000004b000000..0x0000000050efffff (97280 KiB) nomap non-reusable wcnss@4b000000
[    0.000000] OF: reserved mem: 0x0000000050f00000..0x0000000050ffffff (1024 KiB) nomap non-reusable q6_etr_dump@50f00000
[    0.000000] OF: reserved mem: 0x0000000051000000..0x00000000510fffff (1024 KiB) nomap non-reusable m3_dump@51000000
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000040000000-0x000000007fffffff]
[    0.000000]   DMA32    empty
[    0.000000]   Normal   empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000040000000-0x0000000040ffffff]
[    0.000000]   node   0: [mem 0x0000000041000000-0x000000004a3fffff]
[    0.000000]   node   0: [mem 0x000000004a400000-0x00000000510fffff]
[    0.000000]   node   0: [mem 0x0000000051100000-0x000000007fffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000007fffffff]
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.0 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] psci: SMC Calling Convention v1.0
[    0.000000] psci: OSI mode supported.
[    0.000000] psci: [Firmware Bug]: failed to set PC mode: -1
[    0.000000] percpu: Embedded 18 pages/cpu s36200 r8192 d29336 u73728
[    0.000000] Detected VIPT I-cache on CPU0
[    0.000000] alternatives: applying boot alternatives
[    0.000000] Kernel command line: console=ttyMSM0,115200n8 ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashfs rootwait root=/dev/ubiblock0_1
[    0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[    0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes, linear)
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 258048
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] software IO TLB: SWIOTLB bounce buffer size adjusted to 1MB
[    0.000000] software IO TLB: area num 4.
[    0.000000] software IO TLB: mapped [mem 0x000000007eb00000-0x000000007ec00000] (1MB)
[    0.000000] Memory: 885972K/1048576K available (8576K kernel code, 922K rwdata, 1660K rodata, 1600K init, 293K bss, 162604K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] rcu: Hierarchical RCU implementation.
[    0.000000]  Tracing variant of Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[    0.000000] Root IRQ handler: 0xffffffc080010000
[    0.000000] GICv2m: range[mem 0x0b00a000-0x0b00affc], SPI[448:479]
[    0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[    0.000000] arch_timer: cp15 and mmio timer(s) running at 19.20MHz (virt/virt).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns
[    0.000000] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns
[    0.000114] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=192000)
[    0.000127] pid_max: default: 32768 minimum: 301
[    0.005089] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[    0.005104] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[    0.009357] RCU Tasks Trace: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=4.
[    0.009584] rcu: Hierarchical SRCU implementation.
[    0.009589] rcu:     Max phase no-delay instances is 1000.
[    0.010502] smp: Bringing up secondary CPUs ...
[    0.011161] Detected VIPT I-cache on CPU1
[    0.011266] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[    0.011932] Detected VIPT I-cache on CPU2
[    0.012006] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
[    0.012659] Detected VIPT I-cache on CPU3
[    0.012727] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
[    0.012796] smp: Brought up 1 node, 4 CPUs
[    0.012804] SMP: Total of 4 processors activated.
[    0.012809] CPU features: detected: 32-bit EL0 Support
[    0.012814] CPU features: detected: CRC32 instructions
[    0.012873] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching
[    0.012879] CPU: All CPU(s) started at EL1
[    0.012882] alternatives: applying system-wide alternatives
[    0.023460] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.023486] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[    0.025212] pinctrl core: initialized pinctrl subsystem
[    0.027277] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[    0.027906] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations
[    0.027945] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[    0.027980] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[    0.028396] thermal_sys: Registered thermal governor 'step_wise'
[    0.028456] cpuidle: using governor menu
[    0.028672] ASID allocator initialised with 65536 entries
[    0.055313] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4
[    0.057198] Modules: 29456 pages in range for non-PLT usage
[    0.057205] Modules: 520976 pages in range for PLT usage
[    0.060826] SCSI subsystem initialized
[    0.061055] usbcore: registered new interface driver usbfs
[    0.061096] usbcore: registered new interface driver hub
[    0.061149] usbcore: registered new device driver usb
[    0.061603] qcom_scm: convention: smc arm 64
[    0.063319] clocksource: Switched to clocksource arch_sys_counter
[    0.067248] NET: Registered PF_INET protocol family
[    0.067397] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear)
[    0.070188] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes, linear)
[    0.070212] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.070228] TCP established hash table entries: 8192 (order: 4, 65536 bytes, linear)
[    0.070314] TCP bind hash table entries: 8192 (order: 6, 262144 bytes, linear)
[    0.070665] TCP: Hash tables configured (established 8192 bind 8192)
[    0.071166] MPTCP token hash table entries: 1024 (order: 2, 24576 bytes, linear)
[    0.071339] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[    0.071377] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[    0.071711] NET: Registered PF_UNIX/PF_LOCAL protocol family
[    0.071749] PCI: CLS 0 bytes, default 64
[    0.073486] workingset: timestamp_bits=46 max_order=18 bucket_order=0
[    0.074221] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.074228] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.078069] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
[    0.080413] qcom-qmp-usb-phy 78000.phy: supply vdda-phy not found, using dummy regulator
[    0.080586] qcom-qmp-usb-phy 78000.phy: supply vdda-pll not found, using dummy regulator
[    0.081813] qcom-qusb2-phy 79000.phy: supply vdd not found, using dummy regulator
[    0.081954] qcom-qusb2-phy 79000.phy: supply vdda-pll not found, using dummy regulator
[    0.081996] qcom-qusb2-phy 79000.phy: supply vdda-phy-dpdm not found, using dummy regulator
[    0.082158] qcom-qusb2-phy 79000.phy: Registered Qcom-QUSB2 phy
[    0.090604] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.094707] msm_serial 78b1000.serial: msm_serial: detected port #1
[    0.094747] msm_serial 78b1000.serial: uartclk = 19200000
[    0.095060] 78b1000.serial: ttyMSM1 at MMIO 0x78b1000 (irq = 20, base_baud = 1200000) is a MSM
[    0.095526] msm_serial 78b3000.serial: msm_serial: detected port #0
[    0.095560] msm_serial 78b3000.serial: uartclk = 3686400
[    0.095875] 78b3000.serial: ttyMSM0 at MMIO 0x78b3000 (irq = 21, base_baud = 230400) is a MSM
[    0.095907] msm_serial: console setup on port #0
[    0.095950] printk: console [ttyMSM0] enabled
[    0.906601] msm_serial: driver initialized
[    0.916014] loop: module loaded
[    0.917455] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xa1
[    0.917973] nand: Macronix MX30UF1G18AC
[    0.924683] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    0.928175] qcom-nandc 79b0000.nand-controller: Opcode not supported: 238
[    0.935780] Block protection check failed
[    0.943003] 4 fixed-partitions partitions found on MTD device qcom_nand.0
[    0.946643] Creating 4 MTD partitions on "qcom_nand.0":
[    0.953495] 0x000000000000-0x000003400000 : "rootfs_1"
[    0.996714] 0x000003400000-0x000003c00000 : "0:wififw"
[    1.003015] 0x000003c00000-0x000007000000 : "rootfs"
[    1.042133] mtd: setting mtd2 (rootfs) as root device
[    1.042437] mtdsplit: no squashfs found in "rootfs"
[    1.046189] 0x000007000000-0x000007800000 : "0:wififw_1"
[    1.059934] spi_qup 78b5000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64
[    1.060882] spi-nor spi0.0: mx25u6435f (8192 Kbytes)
[    1.066401] 19 fixed-partitions partitions found on MTD device spi0.0
[    1.071350] Creating 19 MTD partitions on "spi0.0":
[    1.077371] 0x000000000000-0x000000050000 : "0:sbl1"
[    1.082624] 0x000000050000-0x000000060000 : "0:mibib"
[    1.087738] 0x000000060000-0x000000080000 : "0:bootconfig"
[    1.092646] 0x000000080000-0x0000000a0000 : "0:bootconfig1"
[    1.098070] 0x0000000a0000-0x000000220000 : "0:qsee_1"
[    1.103533] 0x000000220000-0x0000003a0000 : "0:qsee"
[    1.108753] 0x0000003a0000-0x0000003b0000 : "0:devcfg"
[    1.113977] 0x0000003b0000-0x0000003c0000 : "0:devcfg_1"
[    1.118775] 0x0000003c0000-0x0000003d0000 : "0:apdp"
[    1.124518] 0x0000003d0000-0x0000003e0000 : "0:apdp_1"
[    1.129226] 0x0000003e0000-0x000000420000 : "0:rpm_1"
[    1.134191] 0x000000420000-0x000000460000 : "0:rpm"
[    1.139272] 0x000000460000-0x000000470000 : "0:cdt_1"
[    1.144014] 0x000000470000-0x000000480000 : "0:cdt"
[    1.149148] 0x000000480000-0x000000490000 : "0:appsblenv"
[    1.153861] 0x000000490000-0x000000530000 : "0:appsbl_1"
[    1.159446] 0x000000530000-0x0000005d0000 : "0:appsbl"
[    1.164826] 0x0000005d0000-0x000000610000 : "0:art"
[    1.169801] 0x000000610000-0x000000690000 : "0:ethphyfw"
[    1.182166] spmi spmi-0: PMIC arbiter version v2 (0x20010000)
[    1.274719] i2c_dev: i2c /dev entries driver
[    1.281197] sdhci: Secure Digital Host Controller Interface driver
[    1.281241] sdhci: Copyright(c) Pierre Ossman
[    1.286305] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.292545] remoteproc remoteproc0: releasing cd00000.q6v5_wcss
[    1.315211] NET: Registered PF_INET6 protocol family
[    1.316492] Segment Routing with IPv6
[    1.319286] In-situ OAM (IOAM) with IPv6
[    1.322883] NET: Registered PF_PACKET protocol family
[    1.326873] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    1.331968] 8021q: 802.1Q VLAN Support v1.8
[    1.376988] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4
[    1.377330] cpr4_ipq807x_apss_read_fuse_data: apc_corner: speed bin = 0
[    1.383113] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR fusing revision = 1
[    1.389767] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR misc fuse value = 0
[    1.397409] cpr4_ipq807x_apss_read_fuse_data: apc_corner: Voltage boost fuse config = 0 boost = disable
[    1.404917] cpr3_mem_acc_init: apc: not using memory accelerator regulator
[    1.414049] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused      SVS: open-loop= 704000 uV
[    1.420966] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused      NOM: open-loop= 824000 uV
[    1.430977] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused    TURBO: open-loop= 880000 uV
[    1.440784] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused   STURBO: open-loop= 960000 uV
[    1.450641] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused      SVS: quot[ 7]= 729, quot_offset[ 7]=   0
[    1.460408] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused      NOM: quot[ 7]= 949, quot_offset[ 7]= 220
[    1.471254] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused    TURBO: quot[ 7]=1039, quot_offset[ 7]=  90
[    1.482190] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused   STURBO: quot[ 7]=1181, quot_offset[ 7]= 140
[    1.493391] cpr3_regulator_init_ctrl: apc: Default CPR mode = closed-loop
[    1.496552] cpufreq: cpufreq_online: CPU0: Running at unlisted initial frequency: 800000 KHz, changing to: 1017600 KHz
[    1.512657] remoteproc remoteproc0: cd00000.q6v5_wcss is available
[    1.521824] ubi0: attaching mtd2
[    1.745869] ubi0: scanning is finished
[    1.751936] ubi0: attached mtd2 (name "rootfs", size 52 MiB)
[    1.751969] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    1.756678] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    1.763360] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[    1.770204] ubi0: good PEBs: 416, bad PEBs: 0, corrupted PEBs: 0
[    1.776982] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
[    1.783226] ubi0: max/mean erase counter: 3/0, WL threshold: 4096, image sequence number: 1564983977
[    1.790272] ubi0: available PEBs: 0, total reserved PEBs: 416, PEBs reserved for bad PEB handling: 20
[    1.799561] ubi0: background thread "ubi_bgt0d" started, PID 6▒
[    1.815469] Waiting for root device /dev/ubiblock0_1...
[   31.843346] l11: disabling

4. u-boot factory.ubi image method
    Put openwrt-ipq807x-generic-yuncore_ax880-squashfs-factory.ubi to your TFTP server and rename it to ax880.ubi
    Enter u-boot cli and exec these commands:
    `tftpboot <your_tftp_server_ip>:ax880.ubi`
    After downloading is finished:
    `flash rootfs`
    `flash rootfs_1`
    `reset`

[    0.942980] 4 fixed-partitions partitions found on MTD device qcom_nand.0
[    0.946615] Creating 4 MTD partitions on "qcom_nand.0":
[    0.953497] 0x000000000000-0x000003400000 : "rootfs_1"
[    0.996890] 0x000003400000-0x000003c00000 : "0:wififw"
[    1.003205] 0x000003c00000-0x000007000000 : "rootfs"
[    1.041563] mtd: setting mtd2 (rootfs) as root device
[    1.041866] mtdsplit: no squashfs found in "rootfs"
[    1.045632] 0x000007000000-0x000007800000 : "0:wififw_1"

[    2.464545] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xa1
[    2.468245] nand: ONFI 10-Compliant Macronix MX30UF1G18AC
[    2.474596] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    2.479912] 4 ofpart partitions found on MTD device qcom_nand.0
[    2.487353] Creating 4 MTD partitions on "qcom_nand.0":
[    2.493157] 0x000000000000-0x000003400000 : "rootfs_1"
[    2.537193] 0x000003400000-0x000003c00000 : "0:WIFIFW_1"
[    2.543734] 0x000003c00000-0x000007000000 : "rootfs"
[    2.582174] mtd: device 21 (rootfs) set to be root filesystem
[    2.582431] mtdsplit: no squashfs found in "rootfs"
[    2.586913] 0x000007000000-0x000007800000 : "0:WIFIFW"

ubiformat /dev/${rootfs} -y -f factory.ubi
ubiformat: error!: more then one MTD device specified (use -h for help)

[    3.926797] ubi0: attaching mtd21
[    4.126067] ubi0: scanning is finished
[    4.130865] ubi0: attached mtd21 (name "rootfs", size 52 MiB)
[    4.130882] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    4.135584] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    4.142348] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[    4.149210] ubi0: good PEBs: 416, bad PEBs: 0, corrupted PEBs: 0
[    4.155978] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
[    4.162227] ubi0: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 965740558
[    4.169266] ubi0: available PEBs: 0, total reserved PEBs: 416, PEBs reserved for bad PEB handling: 20
[    4.178214] ubi0: background thread "ubi_bgt0d" started, PID 122
[    4.188347] hctosys: unable to open rtc device (rtc0)
[    4.198446] pmd9655_ldo11: disabling
[    4.199040] ALSA device list:
[    4.202235]   No soundcards found.
[    4.206754] VFS: Mounted root (squashfs filesystem) readonly on device 31:24.
[    4.208484] Freeing unused kernel memory: 232K (ffffffc000807000 - ffffffc000841000)
[    4.215658] Freeing alternatives memory: 44K (ffffffc000841000 - ffffffc00084c000)
[    4.345881] random: nonblocking pool is initialized
[    4.482269] init: Console is alive
[    4.482367] init: - watchdog -
[    5.221200] Button Hotplug driver version 0.4.1
[    5.223590] SCSI subsystem initialized
[    5.484951] init: - preinit -
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
Before mount_root
[    7.622528] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" started, PID 159
[    7.649362] UBIFS (ubi0:2): recovery needed
[    7.758287] UBIFS (ubi0:2): recovery completed
[    7.758338] UBIFS (ubi0:2): UBIFS: mounted UBI device 0, volume 2, name "rootfs_data"
[    7.761624] UBIFS (ubi0:2): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    7.769545] UBIFS (ubi0:2): FS size: 21331968 bytes (20 MiB, 168 LEBs), journal size 1015809 bytes (0 MiB, 8 LEBs)
[    7.779427] UBIFS (ubi0:2): reserved for root: 1007561 bytes (983 KiB)
[    7.789658] UBIFS (ubi0:2): media format: w4/r0 (latest is w4/r0), UUID 7F8C1EB4-B675-4C49-BAAD-60CE8E55029B, small LPT model
[    7.797817] mount_root: switching to jffs2 overlay
After mount_root
12064+0 records in
12064+0 records out
12064 bytes (11.8KB) copied, 0.030787 seconds, 382.7KB/s
131072+0 records in
131072+0 records out
131072 bytes (128.0KB) copied, 0.237157 se[    8.094943] procd: - early -
[    8.098068] procd: - watchdog -
conds, 539.7KB/s
[    8.727371] procd: - ubus -
[    9.729274] procd: - init -
Please press Enter to activate this console.
[    9.932394] ubi1: attaching mtd22
[    9.962558] ubi1: scanning is finished
[    9.967246] ubi1: attached mtd22 (name "0:WIFIFW", size 8 MiB)
[    9.967266] ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    9.971960] ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    9.978834] ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
[    9.985693] ubi1: good PEBs: 64, bad PEBs: 0, corrupted PEBs: 0
[    9.992445] ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
[    9.998356] ubi1: max/mean erase counter: 0/0, WL threshold: 4096, image sequence number: 336461941
[   10.005650] ubi1: available PEBs: 22, total reserved PEBs: 42, PEBs reserved for bad PEB handling: 20
[   10.014599] ubi1: background thread "ubi_bgt1d" started, PID 575
 WIFI FW mount is successful

[    1.521824] ubi0: attaching mtd2
[    1.745869] ubi0: scanning is finished
[    1.751936] ubi0: attached mtd2 (name "rootfs", size 52 MiB)
[    1.751969] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    1.756678] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    1.763360] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[    1.770204] ubi0: good PEBs: 416, bad PEBs: 0, corrupted PEBs: 0
[    1.776982] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
[    1.783226] ubi0: max/mean erase counter: 3/0, WL threshold: 4096, image sequence number: 1564983977
[    1.790272] ubi0: available PEBs: 0, total reserved PEBs: 416, PEBs reserved for bad PEB handling: 20
[    1.799561] ubi0: background thread "ubi_bgt0d" started, PID 6▒
[    1.815469] Waiting for root device /dev/ubiblock0_1...
[   31.843346] l11: disabling

[    1.522092] ubi0: attaching mtd2
[    1.749544] ubi0: scanning is finished
[    1.755587] ubi0: attached mtd2 (name "rootfs", size 52 MiB)
[    1.755625] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    1.760319] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    1.767018] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[    1.773866] ubi0: good PEBs: 416, bad PEBs: 0, corrupted PEBs: 0
[    1.780629] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
[    1.786888] ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 1750711236
[    1.793928] ubi0: available PEBs: 0, total reserved PEBs: 416, PEBs reserved for bad PEB handling: 20
[    1.803213] ubi0: background thread "ubi_bgt0d" started, PID 683
[    1.803963] block ubiblock0_1: created from ubi0:1(roo▒[    1.826877] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[    1.827457] Freeing unused kernel memory: 1600K
[    1.833204] Run /sbin/init as init process
[    1.968536] init: Console is alive
[    1.968657] init: - watchdog -
[    1.992784] kmodloader: no module folders for kernel version 6.6.93 found
[    2.001595] init: - preinit -
[    7.603335] random: crng init done
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[   11.880797] UBIFS (ubi0:2): Mounting in unauthenticated mode
[   11.880924] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" started, PID 794
[   11.915103] UBIFS (ubi0:2): recovery needed
[   12.002907] UBIFS (ubi0:2): recovery completed
[   12.003006] UBIFS (ubi0:2): UBIFS: mounted UBI device 0, volume 2, name "rootfs_data"
[   12.006280] UBIFS (ubi0:2): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[   12.014166] UBIFS (ubi0:2): FS size: 35807232 bytes (34 MiB, 282 LEBs), max 292 LEBs, journal size 1777664 bytes (1 MiB, 14 LEBs)
[   12.024071] UBIFS (ubi0:2): reserved for root: 1691263 bytes (1651 KiB)
[   12.035688] UBIFS (ubi0:2): media format: w5/r0 (latest is w5/r0), UUID 183E5F3D-52A6-41F8-8EAD-A265EDAAA1A4, small LPT model
[   12.044280] mount_root: switching to ubifs overlay
[   12.056936] overlayfs: null uuid detected in lower fs '/', falling back to xino=off,index=off,nfs_export=off.
[   12.061908] urandom-seed: Seeding with /etc/urandom.seed
[   12.114416] procd: - early -
[   12.114521] procd: - watchdog -
[   12.674358] procd: - watchdog -
[   12.675672] procd: - ubus -
[   12.828691] procd: - init -
Please press Enter to activate this console.
[   13.051762] kmodloader: no module folders for kernel version 6.6.93 found
[   13.232312] urngd: v1.0.2 started.
[   31.843383] l11: disabling