1 Temat przez armen10 (edytowany przez armen10 2025-07-04 11:41:54)

  • Zarejestrowany: 2014-12-17
  • Posty: 261

Temat: TL-MR3020 v3 + Huawei HiLink E3273

Cześć, nie mogę znaleźć właściwego opisu, aby móc podłączyć poniższy modem USB. Czy mógłbym prosić o pomc? Jak sposób (tryb) byłby właściwy ?
Router: TL-MR3020 v3
Firmware：OpenWrt 21.02-SNAPSHOT r16847-f8282da11e
Modem USB: Huawei HiLink E3273 (Orange)


Log:

root@OpenWrt_MR3020:~# dmesg | grep -i usb
[    5.163907] usbcore: registered new interface driver usbfs
[    5.169649] usbcore: registered new interface driver hub
[    5.175167] usbcore: registered new device driver usb
[    5.238906] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    5.288590] phy phy-10120000.usbphy.0: remote usb device wakeup disabled
[    5.295408] phy phy-10120000.usbphy.0: UTMI 16bit 30MHz
[    5.306585] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
[    5.333230] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
[    5.340645] hub 1-0:1.0: USB hub found
[    5.355619] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    5.376007] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
[    5.454297] hub 2-0:1.0: USB hub found
[    5.472965] usbcore: registered new interface driver usb-storage
[    5.482087] usbcore: registered new interface driver uas
[    6.749316] usb 1-1: new high-speed USB device number 2 using ehci-platform
[   18.593150] usbcore: registered new interface driver cdc_acm
[   18.598978] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[   18.643026] usbcore: registered new interface driver cdc_wdm
[   18.784466] usbcore: registered new interface driver usblp
[   18.841102] usbcore: registered new interface driver usbserial_generic
[   18.847911] usbserial: USB Serial support registered for generic
[   18.927337] usbcore: registered new interface driver cdc_ether
[   18.960736] usbcore: registered new interface driver cdc_ncm
[   19.110318] usbcore: registered new interface driver huawei_cdc_ncm
[   20.628329] usbcore: registered new interface driver qmi_wwan
[   20.681313] usbcore: registered new interface driver rndis_host
[   20.691164] usbcore: registered new interface driver sierra
[   20.696979] usbserial: USB Serial support registered for Sierra USB modem
[   20.707773] usbcore: registered new interface driver sierra_net
[   20.824733] usbcore: registered new interface driver cdc_mbim
[   20.836129] usbcore: registered new interface driver option
[   20.841985] usbserial: USB Serial support registered for GSM modem (1-port)
[   20.860909] usbcore: registered new interface driver qcserial
[   20.866925] usbserial: USB Serial support registered for Qualcomm USB modem
[  200.433892] usb 1-1: new high-speed USB device number 4 using ehci-platform
[  200.785896] usb 1-1: device descriptor read/64, error -71
[  258.529805] usb 1-1: new high-speed USB device number 5 using ehci-platform
[ 1531.679144] usb 1-1: new high-speed USB device number 6 using ehci-platform

2 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,615

Odp: TL-MR3020 v3 + Huawei HiLink E3273

Tu jest opis: https://eko.one.pl/?p=openwrt-3g#obsuga … ejnphilink

Ale u ciebie nie zadziała bo wywaliło ci magistralę usb. Sprawdź kable pomiędzy routerem a modmem lub daj pomiędzy nimi hub usb z własnym zasilaniem.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

3 Odpowiedź przez armen10 (edytowany przez armen10 2025-07-04 11:51:58)

  • Zarejestrowany: 2014-12-17
  • Posty: 261

Odp: TL-MR3020 v3 + Huawei HiLink E3273

Miałem router podpięty tylko przez USB do kompa może za małe napięci... Zarz podłączę zasilacz pod TL-MR3020.
A teraz ?

root@OpenWrt_MR3020:~# dmesg | grep -i usb
[    5.162069] usbcore: registered new interface driver usbfs
[    5.167777] usbcore: registered new interface driver hub
[    5.173303] usbcore: registered new device driver usb
[    5.236335] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    5.286677] phy phy-10120000.usbphy.0: remote usb device wakeup disabled
[    5.293495] phy phy-10120000.usbphy.0: UTMI 16bit 30MHz
[    5.304673] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
[    5.333227] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
[    5.340668] hub 1-0:1.0: USB hub found
[    5.355465] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    5.375928] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
[    5.454299] hub 2-0:1.0: USB hub found
[    5.473171] usbcore: registered new interface driver usb-storage
[    5.482283] usbcore: registered new interface driver uas
[   18.576056] usbcore: registered new interface driver cdc_acm
[   18.581876] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[   18.627008] usbcore: registered new interface driver cdc_wdm
[   18.769278] usbcore: registered new interface driver usblp
[   18.825554] usbcore: registered new interface driver usbserial_generic
[   18.832347] usbserial: USB Serial support registered for generic
[   18.915348] usbcore: registered new interface driver cdc_ether
[   18.932800] usbcore: registered new interface driver cdc_ncm
[   19.086325] usbcore: registered new interface driver huawei_cdc_ncm
[   20.604299] usbcore: registered new interface driver qmi_wwan
[   20.654069] usbcore: registered new interface driver rndis_host
[   20.663896] usbcore: registered new interface driver sierra
[   20.669746] usbserial: USB Serial support registered for Sierra USB modem
[   20.680635] usbcore: registered new interface driver sierra_net
[   20.797769] usbcore: registered new interface driver cdc_mbim
[   20.809100] usbcore: registered new interface driver option
[   20.814936] usbserial: USB Serial support registered for GSM modem (1-port)
[   20.832971] usbcore: registered new interface driver qcserial
[   20.838989] usbserial: USB Serial support registered for Qualcomm USB modem

4 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,615

Odp: TL-MR3020 v3 + Huawei HiLink E3273

Całość logów pokaż

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

5 Odpowiedź przez armen10

  • Zarejestrowany: 2014-12-17
  • Posty: 261

Odp: TL-MR3020 v3 + Huawei HiLink E3273

Niby wszystko jest WAN dostał z USB adres 192.168.1.100, ale neta nie ma...

root@OpenWrt_MR3020:~# cat /etc/config/firewall

config defaults
        option input 'ACCEPT'
        option output 'ACCEPT'
        option forward 'REJECT'
        option synflood_protect '1'

config zone
        option name 'lan'
        option input 'ACCEPT'
        option output 'ACCEPT'
        option forward 'ACCEPT'
        list network 'lan'

config zone
        option name 'wan'
        option input 'REJECT'
        option output 'ACCEPT'
        option forward 'REJECT'
        option masq '1'
        option mtu_fix '1'
        list network 'wan6'
        list network 'wan'

config forwarding
        option src 'lan'
        option dest 'wan'

config rule
        option name 'Allow-DHCP-Renew'
        option src 'wan'
        option proto 'udp'
        option dest_port '68'
        option target 'ACCEPT'
        option family 'ipv4'

config rule
        option name 'Allow-Ping'
        option src 'wan'
        option proto 'icmp'
        option icmp_type 'echo-request'
        option family 'ipv4'
        option target 'ACCEPT'

config rule
        option name 'Allow-IGMP'
        option src 'wan'
        option proto 'igmp'
        option family 'ipv4'
        option target 'ACCEPT'

config rule
        option name 'Allow-DHCPv6'
        option src 'wan'
        option proto 'udp'
        option dest_port '546'
        option family 'ipv6'
        option target 'ACCEPT'

config rule
        option name 'Allow-MLD'
        option src 'wan'
        option proto 'icmp'
        option src_ip 'fe80::/10'
        list icmp_type '130/0'
        list icmp_type '131/0'
        list icmp_type '132/0'
        list icmp_type '143/0'
        option family 'ipv6'
        option target 'ACCEPT'

config rule
        option name 'Allow-ICMPv6-Input'
        option src 'wan'
        option proto 'icmp'
        list icmp_type 'echo-request'
        list icmp_type 'echo-reply'
        list icmp_type 'destination-unreachable'
        list icmp_type 'packet-too-big'
        list icmp_type 'time-exceeded'
        list icmp_type 'bad-header'
        list icmp_type 'unknown-header-type'
        list icmp_type 'router-solicitation'
        list icmp_type 'neighbour-solicitation'
        list icmp_type 'router-advertisement'
        list icmp_type 'neighbour-advertisement'
        option limit '1000/sec'
        option family 'ipv6'
        option target 'ACCEPT'

config rule
        option name 'Allow-ICMPv6-Forward'
        option src 'wan'
        option dest '*'
        option proto 'icmp'
        list icmp_type 'echo-request'
        list icmp_type 'echo-reply'
        list icmp_type 'destination-unreachable'
        list icmp_type 'packet-too-big'
        list icmp_type 'time-exceeded'
        list icmp_type 'bad-header'
        list icmp_type 'unknown-header-type'
        option limit '1000/sec'
        option family 'ipv6'
        option target 'ACCEPT'

config rule
        option name 'Allow-IPSec-ESP'
        option src 'wan'
        option dest 'lan'
        option proto 'esp'
        option target 'ACCEPT'

config rule
        option name 'Allow-ISAKMP'
        option src 'wan'
        option dest 'lan'
        option dest_port '500'
        option proto 'udp'
        option target 'ACCEPT'

root@OpenWrt_MR3020:~# cat /etc/config/network

config interface 'loopback'
        option device 'lo'
        option proto 'static'
        option ipaddr '127.0.0.1'
        option netmask '255.0.0.0'

config globals 'globals'
        option ula_prefix 'fd21:6742:ffc0::/48'

config device
        option name 'br-lan'
        option type 'bridge'
        list ports 'eth0.1'

config interface 'lan'
        option device 'br-lan'
        option proto 'static'
        option netmask '255.255.255.0'
        option ip6assign '60'
        option ipaddr '192.168.20.254'

config switch
        option name 'switch0'
        option reset '1'
        option enable_vlan '1'

config switch_vlan
        option device 'switch0'
        option vlan '1'
        option ports '6t 0'
        option description 'LAN'

config interface 'wan'
        option proto 'dhcp'
        option device 'eth1'

6 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,615

Odp: TL-MR3020 v3 + Huawei HiLink E3273

To teraz wejdź do gui modemu (http://192.168.1.1 pewnie) i kliknij połącz, bo niektóre hlinki domyślnie miały przestawione połączenie na żądanie a nie na stałe. Tak czy siak po stronie routera to wszystko, teraz tylko modem musisz zmusić do połączenia.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

7 Odpowiedź przez armen10

  • Zarejestrowany: 2014-12-17
  • Posty: 261

Odp: TL-MR3020 v3 + Huawei HiLink E3273

Dziękuję za pomoc działa.