Dobra znalazłem dumpa. Wrzuciłem (bez wpisywania art itp na razie) włącza się jest wifi po lanie dostaje IP . Nie działa gui. nie łączy się też z siecią automatycznie. Działa telnet na 23. resetowałem kilka razy do fabryki nie pomaga. Taki log:
U-Boot 1.1.3 (Jun 1 2021 - 08:51:05)
Board: Ralink APSoC DRAM: 32 MB
gpiomode1 55054404.
gpiomode2 05550555.
######GPIO CTRL 1 for GPIO 32~64 OUTPUT tmp(0x00005f90)#####
######GPIO CTRL 1 for GPIO 32~64 INPUT tmp(0x00005f90)#####
flash manufacture id: 1c, device id 70 16
find flash: EN25QH32B
RALINK_GPIOMODE_REG_1(0xb0000060) old=0x55054404 new=0x55054404
RALINK_GPIO_CTRL_32_63(0xb0000604) old=0x5f90 new=0x5f90
RALINK_GPIO_DATA_32_63(0xb0000624) old=0x7f5f new=0x7f4f
============================================
Ralink UBoot Version: 4.3.0.0
--------------------------------------------
ASIC 7628_MP (Port5<->None)
DRAM component: 256 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 32 MBytes
Flash component: SPI Flash
Date:Jun 1 2021 Time:08:51:05
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768
##### The CPU freq = 580 MHZ ####
estimate memory size =32 Mbytes
RESET MT7628 PHY!!!!!!
continue to starting system. 0
disable switch phyport...
3: System Boot system code via Flash.(0xbc010000)
do_bootm:argc=2, addr=0xbc010000
## Booting image at bc010000 ...
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 8000c150) ...
## Giving linux memsize in MB, 32
Starting kernel ...
怘▒▒▒▒ff▒▒~▒▒~fx▒▒▒怘▒怘▒f▒▒▒▒▒▒▒▒f▒f▒▒▒Linux version 2.6.36 (tp-link@Sohoidev) (gcc version 4.6.3 (Buildroot 2012.11.1) ) #1 Tue Jun 1 08:54:10 CST 2021
The CPU feqenuce set to 575 MHz
MIPS CPU sleep mode enabled.
CPU revision is: 00019655 (MIPS 24Kc)
Software DMA cache coherency
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
Normal 0x00000000 -> 0x00002000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00002000
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
Kernel command line: console=ttyS1,115200 root=/dev/mtdblock2 rootfstype=squashfs init=/sbin/init
PID hash table entries: 128 (order: -3, 512 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Primary instruction cache 64kB, VIPT, , 4-waylinesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
Writing ErrCtl register=00024dbb
Readback ErrCtl register=00024dbb
Memory: 29124k/32768k available (2433k kernel code, 3644k reserved, 486k data, 164k init, 0k highmem)
NR_IRQS:128
console [ttyS1] enabled
Calibrating delay loop... 386.04 BogoMIPS (lpj=772096)
pid_max: default: 4096 minimum: 301
Mount-cache hash table entries: 512
NET: Registered protocol family 16
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Switching to clocksource Ralink Systick timer
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
NET: Registered protocol family 1
RT3xxx EHCI/OHCI init.
squashfs: version 4.0 (2009/01/31) Phillip Lougher
msgmni has been set to 56
io scheduler noop registered
io scheduler deadline registered (default)
Ralink gpio driver initialized
Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
serial8250: ttyS0 at MMIO 0x10000d00 (irq = 21) is a 16550A
serial8250: ttyS1 at MMIO 0x10000c00 (irq = 20) is a 16550A
brd: module loaded
flash manufacture id: 1c, device id 70 16
EN25QH32B(1c 70161c30 flash_version = 1) (4096 Kbytes)
mtd .name = raspi, .size = 0x00400000 (4M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
Creating 6 MTD partitions on "raspi":
0x000000000000-0x000000010000 : "boot"
0x000000010000-0x000000110000 : "kernel"
0x000000110000-0x0000003e0000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
0x0000003e0000-0x0000003f0000 : "config"
0x0000003f0000-0x000000400000 : "romfile"
0x0000003f0000-0x000000400000 : "radio"
Register flash device:flash0
PPP generic driver version 2.4.2
PPP MPPE Compression module registered
NET: Registered protocol family 24
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
FM_OUT value: u4FmOut = 0(0x00000000)
FM_OUT value: u4FmOut = 140(0x0000008C)
FM detection done! loop = 1
SR calibration value u1SrCalVal = 6
rt3xxx-ehci rt3xxx-ehci: Ralink EHCI Host Controller
rt3xxx-ehci rt3xxx-ehci: new USB bus registered, assigned bus number 1
rt3xxx-ehci rt3xxx-ehci: irq 18, io mem 0x101c0000
rt3xxx-ehci rt3xxx-ehci: USB 0.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
rt3xxx-ohci rt3xxx-ohci: RT3xxx OHCI Controller
rt3xxx-ohci rt3xxx-ohci: new USB bus registered, assigned bus number 2
rt3xxx-ohci rt3xxx-ohci: irq 18, io mem 0x101c1000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (455 buckets, 1820 max)
ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Linux
TCP cubic registered
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
Ebtables v2.0 registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 164k freed
starting pid 30, tty '': '/etc/init.d/rcS'
cp: can't stat '/etc/SingleSKU_FCC.dat': No such file or directory
insmod: can't insert '/lib/modules/kmdir/kernel/drivers/scsi/scsi_mod.ko': No such file or directory
insmod: can't insert '/lib/modules/kmdir/kernel/drivers/scsi/sd_mod.ko': No such file or directory
insmod: can't insert '/lib/modules/kmdir/kernel/drivers/usb/core/usbcore.ko': No such file or directory
Started WatchDog Timer.
Ralink APSoC Hardware Watchdog Timer
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
insmod: can't insert '/lib/modules/kmdir/kernel/drivers/usb/host/ifxusb_host.ko': No such file or directory
spiflash_ioctl_read, Read from 0x003ff900 length 0x6, ret 0, retlen 0x6
Read MAC from flash(0x3FF900) ffffffff-ffffffff-ffffffff-ffffffff-ffffffff-ffffffff
Read MAC NULL, set default MAC: 00-0c-43-28-ffffff80-02
GMAC1_MAC_ADRH -- : 0x0000000c
GMAC1_MAC_ADRL -- : 0x43288002
Ralink APSoC Ethernet Driver Initilization. v3.1 256 rx/tx descriptors allocated, mtu = 1500!
spiflash_ioctl_read, Read from 0x003ff900 length 0x6, ret 0, retlen 0x6
Read MAC from flash(0x3FF900) ffffffff-ffffffff-ffffffff-ffffffff-ffffffff-ffffffff
Read MAC NULL, set default MAC: 00-0c-43-28-ffffff80-02
GMAC1_MAC_ADRH -- : 0x0000000c
GMAC1_MAC_ADRL -- : 0x43288002
PROC INIT OK!
dns_init
domain_name:tplinkmodem.net
L2TP core driver, V2.0
PPPoL2TP kernel driver, V2.0
Please press Enter to activate this console. [err] syslogd[main --1001] syslogd : syslogd_init
/var/tmp/dconf/rc.router: line 78: ebtables: not found
[ dm_readFile ] 2042: can not open xml file /var/tmp/pc/reduced_data_model.xml!, about to open file /etc/reduced_data_model.xml
spiflash_ioctl_read, Read from 0x003e0000 length 0x10000, ret 0, retlen 0x10000
spiflash_ioctl_read, Read from 0x003e0000 length 0x100, ret 0, retlen 0x100
[ dm_loadCfg ] 2411: software version is not match, in config, version = 0
[ dm_readFile ] 2042: can not open xml file /var/tmp/pc/default_config.xml!, about to open file /etc/default_config.xml
[ parseConfigNode ] 551: Meet unrecognized object node "PhDDNSCfg", skip the node
[ parseConfigNode ] 556: Meet unrecognized parameter node "PhDDNSCfg", skip the node
[ parseConfigNode ] 551: Meet unrecognized object node "X_TP_WDSBridge", skip the node
[ parseConfigNode ] 551: Meet unrecognized object node "X_TP_IPv6Cfg", skip the node
usbcore: registered new interface driver cdc_ether
usbcore: registered new interface driver rndis_host
usbcore: registered new interface driver usbserial
USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
usbserial: USB Serial Driver core
spiflash_ioctl_read, Read from 0x003ffd00 length 0x29, ret 0, retlen 0x29
spiflash_ioctl_read, Read from 0x003ff900 length 0x6, ret 0, retlen 0x6
[ oal_sys_readMaspiflash_ioctl_read, Read from 0x003ffa00 length 0x4, ret 0, retlen 0x4
cFlash ] 1521: Invalid MAC: FF-FF-FF-FF-FF-FF
[ oal_sys_readMacFlash ] 1522: Dut has not been write code, use default mac: 0-A-EB-13-9-69
[ oal_sys_readPinFlash ] 1593: Invalid PIN, Dut has not been write code, set PIN to 12345670
spiflash_ioctl_read, Read from 0x00010000 length 0x200, ret 0, retlen 0x200
spiflash_ioctl_read, Read from 0x003ff900 length 0x6, ret 0, retlen 0x6
[ oal_sys_readMacFlash ] 1521: Invalid MAC: FF-FF-FF-FF-FF-FF
[ oal_sys_readMacFlash ] 1522: Dut has not been write code, use default mac: 0-A-EB-13-9-69
[ ntpc ] 979: Get time zone, g_timeZone = 720
Raeth v3.1 (Tasklet,SkbRecycle)
phy_tx_ring = 0x00d35000, tx_ring = 0xa0d35000
phy_rx_ring0 = 0x00d36000, rx_ring0 = 0xa0d36000
[fe_sw_init:4954]rt305x_esw_init.
disable switch phyport...
GMAC1_MAC_ADRH -- : 0x0000000c
GMAC1_MAC_ADRL -- : 0x43288002
RT305x_ESW: Link Status Changed
sh: can't create /proc/tplink/eth_vlan: nonexistent directory
ioctl: No such device
brctl: bridge br0: Invalid argument
set if eth0.2 to *not wan dev
device eth0.2 entered promiscuous mode
device eth0 entered promiscuous mode
br0: port 1(eth0.2) entering forwarding state
br0: port 1(eth0.2) entering forwarding state
set if eth0.3 to *not wan dev
device eth0.3 entered promiscuous mode
br0: port 2(eth0.3) entering forwarding state
br0: port 2(eth0.3) entering forwarding state
set if eth0.4 to *not wan dev
device eth0.4 entered promiscuous mode
br0: port 3(eth0.4) entering forwarding state
br0: port 3(eth0.4) entering forwarding state
set if eth0.5 to *not wan dev
device eth0.5 entered promiscuous mode
br0: port 4(eth0.5) entering forwarding state
br0: port 4(eth0.5) entering forwarding state
[ vlan_addLanPortsIntoBridge ] 539: add lan Port 255 from br0
brctl: bridge br0: Device or resource busy
brctl: bridge br0: Device or resource busy
brctl: bridge br0: Device or resource busy
brctl: bridge br0: Device or resource busy
[ rsl_initVlanObj ] 982:
+++++++++++++rsl_initVlanObj done!
ra0 no private ioctls.
MT7628-->
=== pAd = c0a10000, size = 909280 ===
<-- RTMPAllocAdapterBlock, Status=0
MT7628-->RtmpChipOpsHook(494): Not support for HIF_MT yet!
MT7628-->mt7628_init()-->
MT7628-->mt7628_init(FW(8a00), HW(8a01), CHIPID(7628))
MT7628-->e2.bin mt7628_init(1143)::(2), pChipCap->fw_len(64736)
MT7628-->mt_bcn_buf_init(218): Not support for HIF_MT yet!
MT7628--><--mt7628_init()
spiflash_ioctl_read, Read from 0x003ffe00 length 0xf, ret 0, retlen 0xf
1538352006 [src/base/mobile_client.cpp PostEvent](630) ERROR: Post event to MOBILE server failed, errno = 2 (No such file or directory).
[err] syslogd[syslogd_msg_process_thread --881] begin to lost!, msg = ERROR: Post event to MOBILE server failed, errno = 2 (No such file or directory).
1538352006 [src/comm/client_comm.cpp GetSoftVersion](2768) ERROR: Client communication with server failed.
[ oal_ltedev_getStatus ] 2164: GetSoftVersion from mobile error!!
[ oal_wlan_ra_lteCoexistence ] 7446: Get Curr band err 0.
No need to switch sht:pAd->ApBootFlag = TRUE
channel.
[ oal_MT7628-->wlan_ra_lteCoexiTX_BCN DESC a1afb000 size = 320
stence ] 7553: MT7628-->
AutoChannelSkiRX[0] DESC a1afd000 size = 4096
pList = 12;13
MT7628-->
RX[1] DESC a0d80000 size = 2048
MT7628-->cfg_mode=9
MT7628-->cfg_mode=9
MT7628-->wmode_band_equal(): Band Equal!
MT7628-->AndesSendCmdMsg: Could not send in band command due to diable fRTMP_ADAPTER_MCU_SEND_IN_BAND_CMD
MT7628-->APSDCapable[0]=1
MT7628-->APSDCapable[1]=1
MT7628-->APSDCapable[2]=1
MT7628-->APSDCapable[3]=1
MT7628-->APSDCapable[4]=1
MT7628-->APSDCapable[5]=1
MT7628-->APSDCapable[6]=1
MT7628-->APSDCapable[7]=1
MT7628-->APSDCapable[8]=1
MT7628-->APSDCapable[9]=1
MT7628-->APSDCapable[10]=1
MT7628-->APSDCapable[11]=1
MT7628-->APSDCapable[12]=1
MT7628-->APSDCapable[13]=1
MT7628-->APSDCapable[14]=1
MT7628-->APSDCapable[15]=1
MT7628-->Key1Str is Invalid key length(0) or Type(0)
MT7628-->Key1Str is Invalid key length(0) or Type(0)
MT7628-->Key2Str is Invalid key length(0) or Type(0)
MT7628-->Key2Str is Invalid key length(0) or Type(0)
MT7628-->Key3Str is Invalid key length(0) or Type(0)
MT7628-->Key3Str is Invalid key length(0) or Type(0)
MT7628-->Key4Str is Invalid key length(0) or Type(0)
MT7628-->Key4Str is Invalid key length(0) or Type(0)
MT7628-->WscKeyASCII=8
MT7628-->WscKeyASCII=8
MT7628-->Smart Carrier Sense = 0
MT7628-->load fw image from fw_header_image
MT7628-->AndesMTLoadFwMethod1(2264)::pChipCap->fw_len(64736)
MT7628-->FW Version:1MT7628-->
MT7628-->FW Build Date:20170411104110MT7628-->
MT7628-->CmdAddressLenReq:(ret = 0)
MT7628-->CmdFwStartReq: override = 1, address = 1048576
MT7628-->CmdStartDLRsp: WiFI FW Download Success
MT7628-->MtAsicDMASchedulerInit(): DMA Scheduler Mode=0(LMAC)
efuse_probe: efuse = 10000012
MT7628-->RtmpChipOpsEepromHook::e2p_type=2, inf_Type=4
MT7628-->RtmpEepromGetDefault::e2p_dafault=2
MT7628-->RtmpChipOpsEepromHook: E2P type(2), E2pAccessMode = 2, E2P default = 2
MT7628-->NVM is FLASH mode
MT7628-->1. Phy Mode = 14
exec!
spiflash_ioctl_read, Read from 0x003f0000 length 0x400, ret 0, retlen 0x400
eeFlashId = 0xffff!
!! default cal bin is /etc/MT7628_EEPROM_20140317.bin
MT7628-->The EEPROM in Flash is wrong, use default
eeFlashId = 0x7628!
MT7628-->Country Region from e2p = ffff
tssi_1_target_pwr_g_band = 30
MT7628-->2. Phy Mode = 14
MT7628-->3. Phy Mode = 14
MT7628-->NICInitPwrPinCfg(11): Not support for HIF_MT yet!
MT7628-->NICInitializeAsic(651): Not support rtmp_mac_sys_reset () for HIF_MT yet!
MT7628-->mt_mac_init()-->
MT7628-->MtAsicInitMac()-->
MT7628-->mt7628_init_mac_cr()-->
MT7628-->MtAsicSetMacMaxLen(1277): Set the Max RxPktLen=450!
MT7628--><--mt_mac_init()
MT7628--> WTBL Segment 1 info:
MT7628--> MemBaseAddr/FID:0x28000/0
MT7628--> EntrySize/Cnt:32/128
MT7628--> WTBL Segment 2 info:
MT7628--> MemBaseAddr/FID:0x40000/0
MT7628--> EntrySize/Cnt:64/128
MT7628--> WTBL Segment 3 info:
MT7628--> MemBaseAddr/FID:0x42000/64
MT7628--> EntrySize/Cnt:64/128
MT7628--> WTBL Segment 4 info:
MT7628--> MemBaseAddr/FID:0x44000/128
MT7628--> EntrySize/Cnt:32/128
MT7628-->AntCfgInit(2956): Not support for HIF_MT yet!
MT7628-->MCS Set = ff ff 00 00 01
MT7628-->MtAsicSetChBusyStat(861): Not support for HIF_MT yet!
open DNS error: No such file or directory
[ oal_sys_getOldTZInfo ] 812: Open TZ file error!
MT7628-->[PMF]ap_pmf_init:: apidx=0, MFPC=0, MFPR=0, SHA256=0
MT7628-->[PMF]RTMPMakeRsnIeCap: RSNIE Capability MFPC=0, MFPR=0
MT7628-->[PMF]ap_pmf_init:: apidx=1, MFPC=0, MFPR=0, SHA256=0
MT7628-->MtAsicSetRalinkBurstMode(3143): Not support for HIF_MT yet!
MT7628-->MtAsicSetPiggyBack(796): Not support for HIF_MT yet!
MT7628-->reload DPD from flash , 0x9F = [0000] doReload bit7[0]
MT7628-->CmdLoadDPDDataFromFlash: Channel = 11, DoReload = 0
MT7628-->MtAsicSetTxPreamble(3122): Not support for HIF_MT yet!
MT7628-->CmdSlotTimeSet:(ret = 0)
MT7628-->MtAsicAddSharedKeyEntry(1344): Not support for HIF_MT yet!
MT7628-->The 2-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 2
MT7628-->MtAsicSetPreTbtt(): bss_idx=0, PreTBTT timeout = 0xf0
MT7628-->Main bssid = 00:0a:eb:13:09:69
<==== rt28xx_init, Status=0
MT7628-->@@@ ed_monitor_init : ===>
MT7628-->@@@ ed_monitor_init : <===
MT7628-->mt7628_set_ed_cca: TURN ON EDCCA mac 0x10618 = 0xd7c87d0f, EDCCA_Status=1
sht:pAd->ApBootFlag = FALSE
MT7628-->WiFi Startup Cost (ra0): 3.908s
MT7628-->
====
@@@ ed_status_read: EDCCA TH - H
pAd->ed_trigger_cnt : 0 > 20 || pAd->ed_big_rssi_stat : 0 < 50
====
MT7628-->AddTxSType: already registered TxSType (PID = 32, Format = 0
MT7628-->The 2-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 2
##### mbss_cr_enable, BssId = 1
MT7628-->MtAsicSetPreTbtt(): bss_idx=0, PreTBTT timeout = 0x0
MT7628-->MtAsicSetPiggyBack(796): Not support for HIF_MT yet!
MT7628-->[PMF]ap_pmf_init:: apidx=0, MFPC=0, MFPR=0, SHA256=0
MT7628-->[PMF]RTMPMakeRsnIeCap: RSNIE Capability MFPC=0, MFPR=0
MT7628-->[PMF]ap_pmf_init:: apidx=1, MFPC=0, MFPR=0, SHA256=0
MT7628-->MtAsicSetRalinkBurstMode(3143): Not support for HIF_MT yet!
MT7628-->MtAsicSetPiggyBack(796): Not support for HIF_MT yet!
MT7628-->reload DPD from flash , 0x9F = [0000] doReload bit7[0]
MT7628-->CmdLoadDPDDataFromFlash: Channel = 11, DoReload = 0
MT7628-->MtAsicSetTxPreamble(3122): Not support for HIF_MT yet!
MT7628-->MtAsicAddSharedKeyEntry(1344): Not support for HIF_MT yet!
MT7628-->AddTxSType: already registered TxSType (PID = 32, Format = 0
MT7628-->AddTxSType: already registered TxSType (PID = 33, Format = 0
MT7628-->The 2-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 2
MT7628-->AddTxSType: already registered TxSType (PID = 6, Format = 0
MT7628-->AddTxSType: already registered TxSType (PID = 8, Format = 0
MT7628-->MtAsicSetPreTbtt(): bss_idx=0, PreTBTT timeout = 0xf0
MT7628-->Main bssid = 00:0a:eb:13:09:69
MT7628-->MtAsicSetPreTbtt(): bss_idx=0, PreTBTT timeout = 0x0
MT7628-->MtAsicSetPiggyBack(796): Not support for HIF_MT yet!
MT7628-->[PMF]ap_pmf_init:: apidx=0, MFPC=0, MFPR=0, SHA256=0
MT7628-->[PMF]RTMPMakeRsnIeCap: RSNIE Capability MFPC=0, MFPR=0
MT7628-->[PMF]ap_pmf_init:: apidx=1, MFPC=0, MFPR=0, SHA256=0
MT7628-->MtAsicSetRalinkBurstMode(3143): Not support for HIF_MT yet!
MT7628-->MtAsicSetPiggyBack(796): Not support for HIF_MT yet!
MT7628-->reload DPD from flash , 0x9F = [0000] doReload bit7[0]
MT7628-->CmdLoadDPDDataFromFlash: Channel = 11, DoReload = 0
MT7628-->MtAsicSetTxPreamble(3122): Not support for HIF_MT yet!
MT7628-->MtAsicAddSharedKeyEntry(1344): Not support for HIF_MT yet!
MT7628-->AddTxSType: already registered TxSType (PID = 32, Format = 0
MT7628-->AddTxSType: already registered TxSType (PID = 33, Format = 0
MT7628-->The 2-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 2
MT7628-->AddTxSType: already registered TxSType (PID = 6, Format = 0
MT7628-->AddTxSType: already registered TxSType (PID = 8, Format = 0
MT7628-->MtAsicSetPreTbtt(): bss_idx=0, PreTBTT timeout = 0xf0
MT7628-->Main bssid = 00:0a:eb:13:09:69
MT7628-->Set_ed_chk_proc()::ed_chk=0
MT7628-->mt7628_set_ed_cca: TURN OFF EDCCA mac 0x10618 = 0xd7083f0f, EDCCA_Status=0
MT7628-->AddTxSType: already registered TxSType (PID = 32, Format = 0
MT7628-->The 2-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 2
device ra0 entered promiscuous mode
br0: port 5(ra0) entering forwarding state
br0: port 5(ra0) entering forwarding state
device ra1 entered promiscuous mode
Checking 2.4G caspiflash_ioctl_read, Read from 0x003f0000 length 0x2, ret 0, retlen 0x2
l data...
sh: wlNetlinkTool: not found
DUT is Not Caled. Wireless Lan should not be used.
[ rsl_initHttpdObj ] 774: [device_exist]---count=0
wireless tool : ated_tp open SUCC
using port 5000
wireless tool : ated_tp open SUCC
using port 5001
[ rsl_initHttpdObj ] 774: [device_exist]---count=1
[ rsl_initHttpdObj ] 774: [device_exist]---count=2
[ rsl_initHttpdObj ] 774: [device_exist]---count=3
[ rsl_initHttpdObj ] 774: [device_exist]---count=4
[ rsl_initHttpdObj ] 774: [device_exist]---count=5
[ rsl_initHttpdObj ] 774: [device_exist]---count=6
[ rsl_initHttpdObj ] 774: [device_exist]---count=7
[ rsl_initHttpdObj ] 774: [device_exist]---count=8
[ rsl_initHttpdObj ] 774: [device_exist]---count=9
[ rsl_initHttpdObj ] 774: [device_exist]---count=10
[ rsl_initHttpdObj ] 774: [device_exist]---count=11
[ rsl_initHttpdObj ] 774: [device_exist]---count=12
[ rsl_initHttpdObj ] 774: [device_exist]---count=13
[ rsl_initHttpdObj ] 774: [device_exist]---count=14
[ rsl_initHttpdObj ] 774: [device_exist]---count=15
[ rsl_initHttpdObj ] 774: [device_exist]---count=16
[ rsl_initHttpdObj ] 774: [device_exist]---count=17
[ rsl_initHttpdObj ] 774: [device_exist]---count=18
[ rsl_initHttpdObj ] 774: [device_exist]---count=19
sendto /var/tmp/8 msg 2030 error No such file or directory ,pid 67
[rsl_initWanLteIntfCfgObj 3613] init LTE module, set flowstat [enableDataLimit 0, enablePaymentDay 0, paymentDay 1, limitation 0, warningPercent 90]
ioctl get lte wan flag error: No such device
[initProfileList 430] LTE Module: profile num [1], default profile [1], active profile [0]
[initProfileList 432] DM: profile num [0], default profile [0], active profile [0]
iptables: Bad rule (does a matching rule exist in that chain?).
ifconfig: ioctl 0x8913 failed: No such device
radvd starting
ifconfig: SIOCSIFTXQLEN: No such device
/var/run/dhcp6c_lte0.pid: No such file or directory
sh: can't create /proc/sys/net/ipv6/conf/lte0/accept_ra: nonexistent directory
sh: can't create /proc/sys/net/ipv6/conf/lte0/autoconf: nonexistent directory
[ getPidFromPidFile ] 112: Cann't open file: /var/run/zebra.pid.
[ getPidFromPidFile ] 112: Cann't open file: /var/run/ripd.pid.
iptables: Bad rule (does a matching rule exist in that chain?).
iptables: Bad rule (does a matching rule exist in that chain?).
iptables: Bad rule (does a matching rule exist in that chain?).
nf_nat_rtsp v0.6.21 loading
sh: ebtables: not found
iptables: Bad rule (does a matching rule exist in that chain?).
ip6tables: Bad rule (does a matching rule exist in that chain?).
ip6tables: Bad rule (does a matching rule exist in that chain?).
---------------> save 67 <---------------
.
spiflash_ioctl_erase, erase to 0x003f0000 length 0x0, nerase done
spiflash_ioctl_write, Write to 0x003e0000 length 0x5a20, ret 0, retlen 0x5a20
enable switch phyport...
Set: phy[0].reg[0] = 3900
Set: phy[1].reg[0] = 3900
Set: phy[2].reg[0] = 3900
Set: phy[3].reg[0] = 3900
Set: phy[4].reg[0] = 3900
Set: phy[0].reg[0] = 3300
Set: phy[1].reg[0] = 3300
Set: phy[2].reg[0] = 3300
RT305x_ESW: Link Status Changed
Set: phy[3].reg[0] = 3300
Set: phy[4].reg[0] = 3300
resetMiiPortV over.
Set: phy[0].reg[4] = 01e1
Set: phy[0].reg[0] = 3300
Set: phy[1].reg[4] = 01e1
Set: phy[1].reg[0] = 3300
Set: phy[2].reg[4] = 01e1
Set: phy[2].reg[0] = 3300
Set: phy[3].reg[4] = 01e1
Set: phy[3].reg[0] = 3300
Set: phy[4].reg[4] = 01e1
Set: phy[4].reg[0] = 3300
turn off flow control over.
pidof mobile > /var/tmp/tmppidof
echo -1000 > /proc//oom_score_adj
sh: can't create /proc//oom_score_adj: nonexistent directory
pidof qmuxd > /var/tmp/tmppidof
echo -1000 > /proc//oom_score_adj
sh: can't create /proc//oom_score_adj: nonexistent directory
pidof httpd > /var/tmp/tmppidof
echo -1000 > /proc/385/oom_score_adj
pidof dhcpd > /var/tmp/tmppidof
echo -1000 > /proc/392/oom_score_adj
RT305x_ESW: Link Status Changed
1538352039 [src/base/mobile_client.cpp PostEvent](630) ERROR: Post event to MOBILE server failed, errno = 2 (No such file or directory).
1538352039 [src/comm/client_comm.cpp GetSoftVersion](2768) ERROR: Client communication with server failed.
[ oal_ltedev_getStatus ] 2164: GetSoftVersion from mobile error!!
1538352044 [src/base/mobile_client.cpp PostEvent](630) ERROR: Post event to MOBILE server failed, errno = 2 (No such file or directory).
1538352044 [src/comm/client_comm.cpp GetSoftVersion](2768) ERROR: Client communication with server failed.
[ oal_ltedev_getStatus ] 2164: GetSoftVersion from mobile error!!
1538352044 [src/base/mobile_client.cpp PostEvent](630) ERROR: Post event to MOBILE server failed, errno = 2 (No such file or directory).
1538352044 [src/comm/client_comm.cpp GetSoftVersion](2768) ERROR: Client communication with server failed.
[ oal_ltedev_getStatus ] 2164: GetSoftVersion from mobile error!!
open DNS error: No such file or directory
1538352049 [src/base/mobile_client.cpp PostEvent](630) ERROR: Post event to MOBILE server failed, errno = 2 (No such file or directory).
1538352049 [src/comm/client_comm.cpp GetSoftVersion](2768) ERROR: Client communication with server failed.
[ oal_ltedev_getStatus ] 2164: GetSoftVersion from mobile error!!
1538352054 [src/base/mobile_client.cpp PostEvent](630) ERROR: Post event to MOBILE server failed, errno = 2 (No such file or directory).
1538352054 [src/comm/client_comm.cpp GetSoftVersion](2768) ERROR: Client communication with server failed.
[ oal_ltedev_getStatus ] 2164: GetSoftVersion from mobile error!!
1538352054 [src/base/mobile_client.cpp PostEvent](630) ERROR: Post event to MOBILE server failed, errno = 2 (No such file or directory).
1538352054 [src/comm/client_comm.cpp GetSoftVersion](2768) ERROR: Client communication with server failed.
[ oal_ltedev_getStatus ] 2164: GetSoftVersion from mobile error!!
[ serviceMonitorHandler ] 2086: restart flowstat...
1538352055 INFO: src/flowstat_main.c(18) main(): LTE flowstat process starts working!
1538352055 ERROR: src/flowstat_manage.c(151) get_flow_bytes(): open file /sys/class/net/lte0/statistics/tx_bytes fail
1538352055 ERROR: src/flowstat_manage.c(151) get_flow_bytes(): open file /sys/class/net/lte0/statistics/rx_bytes fail
1538352060 [src/base/mobile_client.cpp PostEvent](630) ERROR: Post event to MOBILE server failed, errno = 2 (No such file or directory).
1538352060 [src/comm/client_comm.cpp GetSoftVersion](2768) ERROR: Client communication with server failed.
[ oal_ltedev_getStatus ] 2164: GetSoftVersion from mobile error!!
MT7628-->PeerAssocReqSanity - IE_HT_CAP
MT7628-->PeerAssocReqSanity - IE_EXT_CAPABILITY!
MT7628-->AP SETKEYS DONE - WPA2, AuthMode(7)=WPA2PSK, WepStatus(6)=AES, GroupWepStatus(6)=AES
MT7628-->Rcv Wcid(1) AddBAReq
MT7628-->Start Seq = 00000000
1538352065 [src/base/mobile_client.cpp PostEvent](630) ERROR: Post event to MOBILE server failed, errno = 2 (No such file or directory).
1538352065 [src/comm/client_comm.cpp GetSoftVersion](2768) ERROR: Client communication with server failed.
[ oal_ltedev_getStatus ] 2164: GetSoftVersion from mobile error!!
1538352065 [src/base/mobile_client.cpp PostEvent](630) ERROR: Post event to MOBILE server failed, errno = 2 (No such file or directory).
1538352065 [src/comm/client_comm.cpp GetSoftVersion](2768) ERROR: Client communication with server failed.
[ oal_ltedev_getStatus ] 2164: GetSoftVersion from mobile error!!
1538352065 [src/base/mobile_client.cpp PostEvent](630) ERROR: Post event to MOBILE server failed, errno = 2 (No such file or directory).
1538352065 [src/comm/client_comm.cpp GetSoftVersion](2768) ERROR: Client communication with server failed.
[ oal_ltedev_getStatus ] 2164: GetSoftVersion from mobile error!!
1538352070 [src/base/mobile_client.cpp PostEvent](630) ERROR: Post event to MOBILE server failed, errno = 2 (No such file or directory).
1538352070 [src/comm/client_comm.cpp GetSoftVersion](2768) ERROR: Client communication with server failed.
[ oal_ltedev_getStatus ] 2164: GetSoftVersion from mobile error!!
1538352070 ERROR: src/flowstat_manage.c(151) get_flow_bytes(): open file /sys/class/net/lte0/statistics/tx_bytes fail
1538352070 ERROR: src/flowstat_manage.c(151) get_flow_bytes(): open file /sys/class/net/lte0/statistics/rx_bytes fail
1538352075 [src/base/mobile_client.cpp PostEvent](630) ERROR: Post event to MOBILE server failed, errno = 2 (No such file or directory).
1538352075 [src/comm/client_comm.cpp GetSoftVersion](2768) ERROR: Client communication with server failed.
[ oal_ltedev_getStatus ] 2164: GetSoftVersion from mobile error!!
1538352075 [src/base/mobile_client.cpp PostEvent](630) ERROR: Post event to MOBILE server failed, errno = 2 (No such file or directory).
1538352075 [src/comm/client_comm.cpp GetSoftVersion](2768) ERROR: Client communication with server failed.
[ oal_ltedev_getStatus ] 2164: GetSoftVersion from mobile error!!
1538352080 [src/base/mobile_client.cpp PostEvent](630) ERROR: Post event to MOBILE server failed, errno = 2 (No such file or directory).
1538352080 [src/comm/client_comm.cpp GetSoftVersion](2768) ERROR: Client communication with server failed.
[ oal_ltedev_getStatus ] 2164: GetSoftVersion from mobile error!!
1538352085 [src/base/mobile_client.cpp PostEvent](630) ERROR: Post event to MOBILE server failed, errno = 2 (No such file or directory).
1538352085 [src/comm/client_comm.cpp GetSoftVersion](2768) ERROR: Client communication with server failed.
[ oal_ltedev_getStatus ] 2164: GetSoftVersion from mobile error!!
1538352085 [src/base/mobile_client.cpp PostEvent](630) ERROR: Post event to MOBILE server failed, errno = 2 (No such file or directory).
1538352085 [src/comm/client_comm.cpp GetSoftVersion](2768) ERROR: Client communication with server failed.
[ oal_ltedev_getStatus ] 2164: GetSoftVersion from mobile error!!
1538352085 ERROR: src/flowstat_manage.c(151) get_flow_bytes(): open file /sys/class/net/lte0/statistics/tx_bytes fail
1538352085 ERROR: src/flowstat_manage.c(151) get_flow_bytes(): open file /sys/class/net/lte0/statistics/rx_bytes fail
1538352090 [src/base/mobile_client.cpp PostEvent](630) ERROR: Post event to MOBILE server failed, errno = 2 (No such file or directory).
1538352090 [src/comm/client_comm.cpp GetSoftVersion](2768) ERROR: Client communication with server failed.
[ oal_ltedev_getStatus ] 2164: GetSoftVersion from mobile error!!
^A1538352094 [src/base/mobile_client.cpp PostEvent](630) ERROR: Post event to MOBILE server failed, errno = 2 (No such file or directory).
1538352094 [src/comm/client_comm.cpp GetSoftVersion](2768) ERROR: Client communication with server failed.
[ oal_ltedev_getStatus ] 2164: GetSoftVersion from mobile error!!
1538352094 [src/base/mobile_client.cpp PostEvent](630) ERROR: Post event to MOBILE server failed, errno = 2 (No such file or directory).
1538352094 [src/comm/client_comm.cpp GetSoftVersion](2768) ERROR: Client communication with server failed.
[ oal_ltedev_getStatus ] 2164: GetSoftVersion from mobile error!!
1538352094 [src/base/mobile_client.cpp PostEvent](630) ERROR: Post event to MOBILE server failed, errno = 2 (No such file or directory).
1538352094 [src/comm/client_comm.cpp GetSoftVersion](2768) ERROR: Client communication with server failed.
[ oal_ltedev_getStatus ] 2164: GetSoftVersion from mobile error!!
^C1538352099 [src/base/mobile_client.cpp PostEvent](630) ERROR: Post event to MOBILE server failed, errno = 2 (No such file or directory).
1538352099 [src/comm/client_comm.cpp GetSoftVersion](2768) ERROR: Client communication with server failed.
[ oal_ltedev_getStatus ] 2164: GetSoftVersion from mobile error!!
1538352100 ERROR: src/flowstat_manage.c(151) get_flow_bytes(): open file /sys/class/net/lte0/statistics/tx_bytes fail
1538352100 ERROR: src/flowstat_manage.c(151) get_flow_bytes(): open file /sys/class/net/lte0/statistics/rx_bytes fail
Będzie z tej mąki chleb czy na złom Cezary?
, no i jeszcze MF289F...