Tam też jest proste założenie , 600Mbps osiągnie , jeśli wszystkie agregowane pasma LTE będą szerokie na maxa ( przy lte to chyba jest 30Mhz) , a takich żaden operator nie ma...

Też mam podobne obserwacje, że przy wyłącznej agregacji UPLOAD, przy DOWNLOAD skacze czasem ponad 300 Mbps, jednak nie wpływa to na średnią maksymalną prędkość.

chrome lub edge, naciśnij ctl-j, wybierz sieć i widzisz jakie elementy się ile ładują .

Duże j , naciśnij jeszcze Shift
tylko później przejdź na zakładkę Network , a potem wpisz adres strony jeszcze raz.

Można się zaskoczyć , że takie wp.pl niby pokazuje szybko , a wczytuje się tak na prawdę dobre 40s...

Masz agregację przecież, z B7 jako podstawowym pasmem i b1/b3 jako dodatkowe. Choc chcesz więcej? Jeżeli nie chcesz B7 (dlaczego?) to podjedź z nim pod inny BTS lub wyłącz ten band, to przełączy się na inny.

Jak nie ma info o nich to i nie ma danych.

I nie, to że masz agregację nie oznacza że będziesz miał prędkości. Jestem dobrym przykładem tego, gdzie w pracy mam LTE cat 19/22 z agregacją 4 pasm i mam 15Mbps w godzinach szczytu

Nie rozumiesz. Masz agregację i masz pasma, a polecenia do odczytu informacji o tym nie dostarczają siły sygnału dla pasm agregowanych. Więc nie wyświetla tego bo nie ma danych.

Dokładnie, to właśnie świadczy że jest agregacja pasm. Inaczej wyświetlał by tylko podstawowe (i tak będzie wyświetlał jak nic nie będziesz pobierał).

Hi guys, I've just subscribed to the forum but I've been reading it for a while, since I bought an MF286D. I'm sorry I don't speak Polish but happy you allow English on the forum I think this is a great forum, with friendly people and a real community.

I'll get to my question about my MF286D, running OpenWrt 24.10.0 and modem firmware BD_TELIAMF286DV1.0.0B12.

I've just tried to update the modem firmware to B14 using the files on this site, but after the process I'm getting I/O errors, see below. I haven't rebooted the router. What would you guys do next?

root@r3:/tmp# mtd write /tmp/mtd8.bin /dev/mtd8
Unlocking /dev/mtd8 ...

Writing from /tmp/mtd8.bin to /dev/mtd8 ...     
root@r3:/tmp# 
root@r3:/tmp# mtd write /tmp/mtd9.bin /dev/mtd9
Unlocking /dev/mtd9 ...

Writing from /tmp/mtd9.bin to /dev/mtd9 ...     
root@r3:/tmp# 

root@r3:/tmp# reboot
-ash: reboot: I/O error
root@r3:/tmp#

logread:

Mon Feb 24 10:51:55 2025 kern.err kernel: [156045.462633] SQUASHFS error: Unable to read directory block [106052a:0]
Mon Feb 24 10:51:55 2025 kern.err kernel: [156045.468823] SQUASHFS error: Unable to read metadata cache entry [1059db4]
Mon Feb 24 10:51:55 2025 kern.err kernel: [156045.475156] SQUASHFS error: Unable to read metadata cache entry [106052a]
Mon Feb 24 10:51:55 2025 kern.err kernel: [156045.481889] SQUASHFS error: Unable to read directory block [106052a:0]

Thanks for the fast reply. I still have an ssh session open to the router and I can still transfer files to it but for example the web interface isn't working.

I don't have a backup of mtd8 and mtd9 from OpenWrt. Which version should I install to get OpenWrt back working?

I've tried flashing the B12 mtd8 and mtd9 from this site but I'm still getting the errors.

I'd prefer to avoid opening the router again if possible.

I can't seem to download that file, it keeps getting stuck at 56.06%

Edit: now I'm getting "bus error" to every command, including "mtd write"

Edit2: now I'm getting "Segmentation fault" to every command, I guess I'll reboot and hope that I haven't caused too much damage.

Edit3: rebooted to the Nordics webgui... I got mislead by a post on the OpenWrt forum that suggested the B14 mtd8 and mtd9 files were modem updates, so I went straight to flashing them... it's been a long time since I flashed OpenWrt on the router and I didn't remember the details.

Now it's asking for a password which I don't have, I guess the next step would be to open up the router and start over again, right?

You were right about waiting, still only 52%... but the most time consuming thing will be opening up the box again to flash OpenWrt.. what a PITA.

I should have posted here before trying to update, you guys are really helpful. What I was trying to achieve was changing the dial tone on the FXS ports with AT commands or adb, but I wanted to ask my question here with an up to date modem firmware...

Edit: not looking good, when I looked at it last it was at 98%, I came back and the state was DISCONNECT and progress 0%. I waited and eventually power cycled the router, now it's totally unresponsive, only the power led is on and I can't even get an IP from it via DHCP.

Edit2: I left it powered off for a while and now DHCP is working and the router is seen by the framework as Nordic B02. admin doesn't work as a password. I can't find the guide I used from this point on, it's been a couple of years since I did it. I remember I had to take it from B02 to B12 via OTA and it took almost an entire day. I'll continue tomorrow. If you guys have any up to date guide handy please let me know.

Edit3: with a fresh mind this morning I found the guide I had used, it was on an Italian forum, duh! :homer: