***************************************
*     U-Boot 1.1.4-09c39dda-dirty     *
*          Build: 2025-02-07          *
***************************************

  BOARD: TP-Link TL-WDR43x0 v1
    SOC: AR9344 rev. 2
    CPU: MIPS 74Kc
    RAM: 128 MB DDR2 32-bit CL3-4-4-10
  FLASH: 8 MB Winbond W25Q64
   PCIe: 168C:0033
    MAC: xxxxx
 CLOCKS: CPU/RAM/AHB/SPI/REF
         550/400/200/ 25/ 40 MHz

Hit any key to stop booting:  0

Booting image from 0x9F020000...

   Vendor/image name:    OpenWrt r16847-f8282da11e
   Hardware ID:          0x43000001
   Whole image size:     7.8 MB (8126464 bytes)
   Kernel size:          2 MB (2057127 bytes)
   Rootfs size:          5.2 MB (5480726 bytes)
   Kernel load address:  0x80060000
   Kernel entry point:   0x80060000

   Header CRC...  skipped
   Data CRC...    skipped

Stopping network... OK!
Uncompressing Kernel... OK!
Starting kernel...

[    0.000000] Linux version 5.4.238 (cezary@eko.one.pl) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r16500-b99d7aecc8)) #0 Mon Apr 17 13:15:36 2023
[    0.000000] printk: bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 0001974c (MIPS 74Kc)
[    0.000000] MIPS: machine is TP-Link TL-WDR4300 v1
[    0.000000] SoC: Atheros AR9344 rev 2
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 32480
[    0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 122116K/131072K available (5303K kernel code, 184K rwdata, 688K rodata, 1240K init, 204K bss, 8956K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS: 51
[    0.000000] CPU clock: 550.000 MHz
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6950037990 ns
[    0.000010] sched_clock: 32 bits at 275MHz, resolution 3ns, wraps every 7809031678ns
[    0.008784] Calibrating delay loop... 273.66 BogoMIPS (lpj=547328)
[    0.055637] pid_max: default: 32768 minimum: 301
[    0.060982] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.069149] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.083720] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.094644] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[    0.102369] pinctrl core: initialized pinctrl subsystem
[    0.112069] NET: Registered protocol family 16
[    0.154179] clocksource: Switched to clocksource MIPS
[    0.160988] thermal_sys: Registered thermal governor 'step_wise'
[    0.161407] NET: Registered protocol family 2
[    0.173321] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
[    0.182435] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[    0.191849] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.200414] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.208287] TCP: Hash tables configured (established 1024 bind 1024)
[    0.215525] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[    0.222879] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[    0.231040] NET: Registered protocol family 1
[    0.235981] PCI: CLS 0 bytes, default 32
[    0.245470] workingset: timestamp_bits=14 max_order=15 bucket_order=1
[    0.260710] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.267269] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.297122] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[    0.310147] pinctrl-single 1804002c.pinmux: 544 pins, size 68
[    0.317591] gpio-export gpio-export: 4 gpio(s) exported
[    0.324373] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.334287] printk: console [ttyS0] disabled
[    0.339123] 18020000.uart: ttyS0 at MMIO 0x18020000 (irq = 9, base_baud = 2500000) is a 16550A
[    0.348760] printk: console [ttyS0] enabled
[    0.348760] printk: console [ttyS0] enabled
[    0.357662] printk: bootconsole [early0] disabled
[    0.357662] printk: bootconsole [early0] disabled
[    0.393540] spi-nor spi0.0: s25fl064k (8192 Kbytes)
[    0.398576] 3 fixed-partitions partitions found on MTD device spi0.0
[    0.405073] OF: Bad cell count for /ahb/spi@1f000000/flash@0/partitions
[    0.411817] OF: Bad cell count for /ahb/spi@1f000000/flash@0/partitions
[    0.418869] Creating 3 MTD partitions on "spi0.0":
[    0.423797] 0x000000000000-0x000000020000 : "u-boot"
[    0.429948] 0x000000020000-0x0000007f0000 : "firmware"
[    0.439093] 2 tplink-fw partitions found on MTD device firmware
[    0.445162] Creating 2 MTD partitions on "firmware":
[    0.450225] 0x000000000000-0x0000001f65a7 : "kernel"
[    0.456425] 0x0000001f65a8-0x0000007d0000 : "rootfs"
[    0.462608] mtd: device 3 (rootfs) set to be root filesystem
[    0.470849] 1 squashfs-split partitions found on MTD device rootfs
[    0.477199] 0x000000740000-0x0000007d0000 : "rootfs_data"
[    0.483831] 0x0000007f0000-0x000000800000 : "art"
[    0.835490] switch0: Atheros AR8327 rev. 4 switch registered on mdio.0
[    1.420350] ag71xx 19000000.eth: connected to PHY at mdio.0:00 [uid=004dd034, driver=Atheros AR8216/AR8236/AR8316]
[    1.431590] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode: rgmii
[    1.438238] i2c /dev entries driver
[    1.444825] NET: Registered protocol family 10
[    1.456859] Segment Routing with IPv6
[    1.460812] NET: Registered protocol family 17
[    1.465436] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    1.478604] 8021q: 802.1Q VLAN Support v1.8
[    1.484142] PCI host bridge /ahb/pcie-controller@180c0000 ranges:
[    1.490419]  MEM 0x0000000010000000..0x0000000013ffffff
[    1.495739]   IO 0x0000000000000000..0x0000000000000000
[    1.501257] PCI host bridge to bus 0000:00
[    1.505462] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff]
[    1.512445] pci_bus 0000:00: root bus resource [io  0x0000]
[    1.518109] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    1.525008] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    1.533096] pci 0000:00:00.0: [168c:0033] type 00 class 0x028000
[    1.539259] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x0001ffff 64bit]
[    1.546211] pci 0000:00:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[    1.553110] pci 0000:00:00.0: supports D1
[    1.557196] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[    1.564461] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[    1.571233] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1001ffff 64bit]
[    1.578680] pci 0000:00:00.0: BAR 6: assigned [mem 0x10020000-0x1002ffff pref]
[    1.593325] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
[    1.607407] Freeing unused kernel memory: 1240K
[    1.612038] This architecture does not have kernel memory protection.
[    1.618575] Run /sbin/init as init process
[    2.401704] init: Console is alive
[    2.405542] init: - watchdog -
[    5.049196] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    5.202663] usbcore: registered new interface driver usbfs
[    5.208365] usbcore: registered new interface driver hub
[    5.213880] usbcore: registered new device driver usb
[    5.291892] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    5.309173] SCSI subsystem initialized
[    5.319742] fsl-ehci: Freescale EHCI Host controller driver
[    5.328103] ehci-platform: EHCI generic platform driver
[    5.333768] ehci-platform 1b000000.usb: EHCI Host Controller
[    5.339605] ehci-platform 1b000000.usb: new USB bus registered, assigned bus number 1
[    5.347697] ehci-platform 1b000000.usb: irq 3, io mem 0x1b000000
[    5.366198] ehci-platform 1b000000.usb: USB 2.0 started, EHCI 1.00
[    5.373512] hub 1-0:1.0: USB hub found
[    5.377925] hub 1-0:1.0: 1 port detected
[    5.391377] usbcore: registered new interface driver usb-storage
[    5.400602] usbcore: registered new interface driver uas
[    5.407437] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    5.425333] init: - preinit -
[    5.772783] usb 1-1: new high-speed USB device number 2 using ehci-platform
[    6.054865] hub 1-1:1.0: USB hub found
[    6.137249] hub 1-1:1.0: 4 ports detected
[    6.234492] random: procd: uninitialized urandom read (4 bytes read)
[    6.639186] random: jshn: uninitialized urandom read (4 bytes read)
[    6.871053] random: jshn: uninitialized urandom read (4 bytes read)
[    7.297969] random: jshn: uninitialized urandom read (4 bytes read)
[    7.364734] random: jshn: uninitialized urandom read (4 bytes read)
[    7.471574] random: jshn: uninitialized urandom read (4 bytes read)
[    8.482653] eth0: link up (1000Mbps/Full duplex)
[    8.494379] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[    8.506365] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[   12.780931] mount_root: loading kmods from internal overlay
[   12.852680] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[   12.861630] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[   13.363778] jffs2_scan_eraseblock(): End of filesystem marker found at 0x10000
[   13.371136] jffs2_build_filesystem(): unlocking the mtd device...
[   13.371171] done.
[   13.379413] jffs2_build_filesystem(): erasing all blocks after the end marker...
[   14.789043] done.
[   14.798658] jffs2: notice: (621) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[   14.814868] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[   14.822119] block: unable to load configuration (fstab: Entry not found)
[   14.829133] block: attempting to load /tmp/jffs_cfg/etc/config/fstab
[   14.835862] block: unable to load configuration (fstab: Entry not found)
[   14.842864] block: attempting to load /etc/config/fstab
[   14.854067] block: unable to load configuration (fstab: Entry not found)
[   14.861045] block: no usable configuration
[   14.893583] jffs2: notice: (619) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[   15.198061] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[   15.205346] block: unable to load configuration (fstab: Entry not found)
[   15.212345] block: attempting to load /tmp/jffs_cfg/etc/config/fstab
[   15.219063] block: unable to load configuration (fstab: Entry not found)
[   15.226064] block: attempting to load /etc/config/fstab
[   15.231618] block: unable to load configuration (fstab: Entry not found)
[   15.238617] block: no usable configuration
[   15.244484] mount_root: overlay filesystem has not been fully initialized yet
[   15.252969] mount_root: switching to jffs2 overlay
[   15.266456] overlayfs: upper fs does not support tmpfile.
- config restore -
[   16.015500] urandom-seed: Seed file not found (/etc/urandom.seed)
[   16.145512] eth0: link down
[   16.172432] procd: - early -
[   16.175626] procd: - watchdog -
[   16.775198] random: jshn: uninitialized urandom read (4 bytes read)
Failed to connect to ubus
[   16.827073] procd: - watchdog -
[   16.834728] procd: - ubus -
[   17.110396] random: ubusd: uninitialized urandom read (4 bytes read)
[   17.127475] random: ubusd: uninitialized urandom read (4 bytes read)
[   17.151912] procd: - init -
Please press Enter to activate this console.
[   17.937063] random: jshn: uninitialized urandom read (4 bytes read)
[   19.606971] kmodloader: loading kernel modules from /etc/modules.d/*
[   19.795906] urngd: v1.0.2 started.
[   20.208514] RPC: Registered named UNIX socket transport module.
[   20.214585] RPC: Registered udp transport module.
[   20.219369] RPC: Registered tcp transport module.
[   20.224156] RPC: Registered tcp NFSv4.1 backchannel transport module.
[   20.313253] random: crng init done
[   20.316796] random: 35 urandom warning(s) missed due to ratelimiting
[   20.390575] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[   20.470286] fuse: init (API version 7.31)
[   20.498681] usbcore: registered new interface driver cdc_acm
[   20.504480] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[   20.532301] usbcore: registered new interface driver cdc_wdm
[   20.555875] Loading modules backported from Linux version v5.10.168-0-g707c48210a53
[   20.563711] Backport generated by backports.git v5.10.168-1-0-gd990acb2
[   20.638479] usbcore: registered new interface driver usblp
[   20.676673] usbcore: registered new interface driver usbserial_generic
[   20.683463] usbserial: USB Serial support registered for generic
[   20.723834] xt_time: kernel timezone is -0000
[   20.736675] usbcore: registered new interface driver cdc_ether
[   20.758235] usbcore: registered new interface driver cdc_ncm
[   20.850044] usbcore: registered new interface driver huawei_cdc_ncm
[   21.346252] PPP generic driver version 2.4.2
[   21.359701] NET: Registered protocol family 24
[   21.377603] usbcore: registered new interface driver qmi_wwan
[   21.397416] usbcore: registered new interface driver rndis_host
[   21.417076] usbcore: registered new interface driver sierra
[   21.422904] usbserial: USB Serial support registered for Sierra USB modem
[   21.448583] usbcore: registered new interface driver sierra_net
[   21.486721] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information.
[   21.494730] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
[   21.625954] usbcore: registered new interface driver cdc_mbim
[   21.650806] usbcore: registered new interface driver option
[   21.656625] usbserial: USB Serial support registered for GSM modem (1-port)
[   21.688372] usbcore: registered new interface driver qcserial
[   21.694379] usbserial: USB Serial support registered for Qualcomm USB modem
[   21.772951] ieee80211 phy0: Atheros AR9340 Rev:2 mem=0xb8100000, irq=12
[   21.780167] ath9k 0000:00:00.0: enabling device (0000 -> 0002)
[   21.789347] ath9k 0000:00:00.0: Direct firmware load for ath9k-eeprom-pci-0000:00:00.0.bin failed with error -2
[   21.799660] ath9k 0000:00:00.0: Falling back to sysfs fallback for: ath9k-eeprom-pci-0000:00:00.0.bin
[   23.600603] ieee80211 phy1: Atheros AR9300 Rev:4 mem=0xb0000000, irq=14
[   23.638059] kmodloader: done loading kernel modules from /etc/modules.d/*
[   49.510200] eth0: link up (1000Mbps/Full duplex)
[   49.527236] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   49.535161] br-lan: port 1(eth0.1) entered blocking state
[   49.540714] br-lan: port 1(eth0.1) entered disabled state
[   49.546728] device eth0.1 entered promiscuous mode
[   49.551649] device eth0 entered promiscuous mode
[   49.580875] br-lan: port 1(eth0.1) entered blocking state
[   49.586431] br-lan: port 1(eth0.1) entered forwarding state
[   50.506419] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   54.148161] ath: EEPROM regdomain: 0x8268
[   54.152290] ath: EEPROM indicates we should expect a country code
[   54.158492] ath: doing EEPROM country->regdmn map search
[   54.163892] ath: country maps to regdmn code: 0x37
[   54.168765] ath: Country alpha2 being used: PL
[   54.173276] ath: Regpair used: 0x37
[   54.176826] ath: regdomain 0x8268 dynamically updated by user
[   54.182741] ath: EEPROM regdomain: 0x8268
[   54.186828] ath: EEPROM indicates we should expect a country code
[   54.193019] ath: doing EEPROM country->regdmn map search
[   54.198421] ath: country maps to regdmn code: 0x37
[   54.203285] ath: Country alpha2 being used: PL
[   54.207798] ath: Regpair used: 0x37
[   54.211346] ath: regdomain 0x8268 dynamically updated by user
[   58.140609] br-lan: port 2(wlan1) entered blocking state
[   58.146075] br-lan: port 2(wlan1) entered disabled state
[   58.151884] device wlan1 entered promiscuous mode
[   58.328807] br-lan: port 3(wlan0) entered blocking state
[   58.334274] br-lan: port 3(wlan0) entered disabled state
[   58.340124] device wlan0 entered promiscuous mode
[   60.393689] wlan1: authenticate with 50:eb:f8:18:47:9c
[   60.413993] wlan1: send auth to 50:eb:f8:18:47:9c (try 1/3)
[   60.676859] wlan1: authenticate with 50:eb:f8:18:47:9c
[   60.682158] wlan1: send auth to 50:eb:f8:18:47:9c (try 1/3)
[   60.692278] wlan1: authenticated
[   60.698387] wlan1: associate with 50:eb:f8:18:47:9c (try 1/3)
[   60.707948] wlan1: RX AssocResp from 50:eb:f8:18:47:9c (capab=0x111 status=0 aid=3)
[   60.716240] wlan1: associated
[   60.728322] wlan1: Limiting TX power to 23 (26 - 3) dBm as advertised by 50:eb:f8:18:47:9c
[   60.824383] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[   60.831342] br-lan: port 2(wlan1) entered blocking state
[   60.836796] br-lan: port 2(wlan1) entered forwarding state
[   65.985827] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   65.992579] br-lan: port 3(wlan0) entered blocking state
[   65.998025] br-lan: port 3(wlan0) entered forwarding state

[   13.363778] jffs2_scan_eraseblock(): End of filesystem marker found at 0x10000
[   13.371136] jffs2_build_filesystem(): unlocking the mtd device...
[   13.371171] done.
[   13.379413] jffs2_build_filesystem(): erasing all blocks after the end marker...
[   14.789043] done.
[   14.798658] jffs2: notice: (621) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[   14.814868] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[   14.822119] block: unable to load configuration (fstab: Entry not found)
[   14.829133] block: attempting to load /tmp/jffs_cfg/etc/config/fstab
[   14.835862] block: unable to load configuration (fstab: Entry not found)
[   14.842864] block: attempting to load /etc/config/fstab
[   14.854067] block: unable to load configuration (fstab: Entry not found)
[   14.861045] block: no usable configuration
[   14.893583] jffs2: notice: (619) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[   15.198061] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[   15.205346] block: unable to load configuration (fstab: Entry not found)
[   15.212345] block: attempting to load /tmp/jffs_cfg/etc/config/fstab
[   15.219063] block: unable to load configuration (fstab: Entry not found)
[   15.226064] block: attempting to load /etc/config/fstab
[   15.231618] block: unable to load configuration (fstab: Entry not found)
[   15.238617] block: no usable configuration
[   15.244484] mount_root: overlay filesystem has not been fully initialized yet
[   15.252969] mount_root: switching to jffs2 overlay
[   15.266456] overlayfs: upper fs does not support tmpfile.
- config restore -
[   16.015500] urandom-seed: Seed file not found (/etc/urandom.seed)
...
[   21.789347] ath9k 0000:00:00.0: Direct firmware load for ath9k-eeprom-pci-0000:00:00.0.bin failed with error -2
[   21.799660] ath9k 0000:00:00.0: Falling back to sysfs fallback for: ath9k-eeprom-pci-0000:00:00.0.bin