Odp: Nexx WT3020 nie działa po próbie wgrania Garygole
Wszystko jedno, byle by starszą wersję.
Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.
Strony Poprzednia 1 2
Zaloguj się lub zarejestruj by napisać odpowiedź
Nie jesteś zalogowany. Proszę się zalogować lub zarejestrować.
Nexx WT3020 nie działa po próbie wgrania Garygole (Strona 2 z 2)
eko.one.pl → Oprogramowanie / Software → Nexx WT3020 nie działa po próbie wgrania Garygole
Posty: 26 do 42 z 42
Odp: Nexx WT3020 nie działa po próbie wgrania Garygole
dalej nic
U-Boot 1.1.3 (Jan 3 2014 - 09:12:42)
MAX Board: Ralink APSoC DRAM: 64 MB
relocate_code Pointer at: 83fb4000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
******************************
Software System Reset Occurred
******************************
spi_wait_nsec: 29
spi device id: ef 40 17 0 0 (40170000)
find flash: W25Q64BV
raspi_read: from:30000 len:1000
raspi_wait_ready: read_sr fail: fc
*** Warning - bad CRC, using default environment
============================================
Ralink UBoot Version: 4.1.1.0
--------------------------------------------
ASIC 7620_MP (Port5<->None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Jan 3 2014 Time:09:12:42
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768
##### The CPU freq = 580 MHZ ####
estimate memory size =64 Mbytes
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP. 4
You choosed 1
0
raspi_read: from:40028 len:6
raspi_wait_ready: read_sr fail: fc
1: System Load Linux to SDRAM via TFTP.
Please Input new ones /or Ctrl-C to discard
Input device IP (10.10.10.123) ==:10.10.10.123
Input server IP (10.10.10.3) ==:10.10.10.3
Input Linux Kernel filename () ==:21ini.bin
netboot_common, argc= 3
NetTxPacket = 0x83FE4C80
KSEG1ADDR(NetTxPacket) = 0xA3FE4C80
NetLoop,call eth_halt !
NetLoop,call eth_init !
Trying Eth0 (10/100-M)
Waitting for RX_DMA_BUSY status Start... done
ETH_STATE_ACTIVE!!
TFTP from server 10.10.10.3; our IP address is 10.10.10.123
Filename '21ini.bin'.
TIMEOUT_COUNT=10,Load address: 0x80a00000
Loading: Got ARP REPLY, set server/gtwy eth addr (00:00:00:00:00:89)
Got it
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
######################################
done
Bytes transferred = 5850691 (594643 hex)
NetBootFileXferSize= 00594643
raspi_read: from:30000 len:10000
raspi_wait_ready: read_sr fail: fc
Automatic boot of image at addr 0x80A00000 ...
## Booting image at 80a00000 ...
Image Name: MIPS OpenWrt Linux-5.4.238
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 5850627 Bytes = 5.6 MB
Load Address: 80000000
Entry Point: 80000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 64
Starting kernel ...
[ 0.000000] Linux version 5.4.238 (cezary@eko.one.pl) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r16500-b99d7aecc8)) #0 Mon Apr 17 13:15:36 2023
[ 0.000000] Board has DDR1
[ 0.000000] Analog PMU set to hw control
[ 0.000000] Digital PMU set to hw control
[ 0.000000] SoC Type: MediaTek MT7620N ver:2 eco:6
[ 0.000000] printk: bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
[ 0.000000] MIPS: machine is Nexx WT3020 (8M)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 16240
[ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes, linear)
[ 0.000000] Writing ErrCtl register=0007ea90
[ 0.000000] Readback ErrCtl register=0007ea90
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 53732K/65536K available (5137K kernel code, 203K rwdata, 636K rodata, 4896K init, 212K bss, 11804K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 256
[ 0.000000] CPU Clock: 580MHz
[ 0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns
[ 0.000000] systick: enable autosleep mode
[ 0.000000] systick: running - mult: 214748, shift: 32
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns
[ 0.000011] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405115902ns
[ 0.015585] Calibrating delay loop... 385.02 BogoMIPS (lpj=770048)
[ 0.059675] pid_max: default: 32768 minimum: 301
[ 0.069060] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.083468] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.104937] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.124243] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[ 0.137844] pinctrl core: initialized pinctrl subsystem
[ 0.150401] NET: Registered protocol family 16
[ 0.189418] rt2880_gpio 10000600.gpio: registering 24 gpios
[ 0.200457] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[ 0.213067] rt2880_gpio 10000688.gpio: registering 1 gpios
[ 0.223899] rt2880_gpio 10000688.gpio: registering 1 irq handlers
[ 0.241909] clocksource: Switched to clocksource systick
[ 0.253543] thermal_sys: Registered thermal governor 'step_wise'
[ 0.254034] NET: Registered protocol family 2
[ 0.274795] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.290139] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 0.306703] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.321873] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.335886] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.348663] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.361569] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.375758] NET: Registered protocol family 1
[ 0.384349] PCI: CLS 0 bytes, default 32
[ 7.543350] rt-timer 10000100.timer: maximum frequency is 1220Hz
[ 7.557673] workingset: timestamp_bits=14 max_order=14 bucket_order=0
[ 7.579265] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 7.590770] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 7.628187] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 7.645988] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 7.661486] printk: console [ttyS0] disabled
[ 7.669959] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
[ 7.689593] printk: console [ttyS0] enabled
[ 7.689593] printk: console [ttyS0] enabled
[ 7.706179] printk: bootconsole [early0] disabled
[ 7.706179] printk: bootconsole [early0] disabled
[ 7.735502] spi spi0.0: force spi mode3
[ 7.753517] spi-nor spi0.0: s25fl064k (8192 Kbytes)
[ 7.763309] 4 fixed-partitions partitions found on MTD device spi0.0
[ 7.776019] OF: Bad cell count for /palmbus@10000000/spi@b00/flash@0/partitions
[ 7.790614] OF: Bad cell count for /palmbus@10000000/spi@b00/flash@0/partitions
[ 7.805443] Creating 4 MTD partitions on "spi0.0":
[ 7.815026] 0x000000000000-0x000000030000 : "u-boot"
[ 7.826093] 0x000000030000-0x000000040000 : "u-boot-env"
[ 7.837784] 0x000000040000-0x000000050000 : "factory"
[ 7.849051] 0x000000050000-0x000000800000 : "firmware"
[ 7.865267] 2 uimage-fw partitions found on MTD device firmware
[ 7.877140] Creating 2 MTD partitions on "firmware":
[ 7.887049] 0x000000000000-0x00000017fc92 : "kernel"
[ 7.898198] 0x00000017fc92-0x0000007b0000 : "rootfs"
[ 7.909133] mtd: device 5 (rootfs) set to be root filesystem
[ 7.922974] 1 squashfs-split partitions found on MTD device rootfs
[ 7.935372] 0x000000461000-0x0000007b0000 : "rootfs_data"
[ 7.958843] gsw: setting port4 to ephy mode
[ 7.967522] mtk_soc_eth 10100000.ethernet: no mdio-bus child node found
[ 7.980745] mtk_soc_eth 10100000.ethernet: mdio-bus disabled
[ 7.992235] mtk_soc_eth 10100000.ethernet: loaded mt7620 driver
[ 8.004800] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
[ 8.021891] rt2880_wdt 10000120.watchdog: Initialized
[ 8.033761] NET: Registered protocol family 10
[ 8.047996] Segment Routing with IPv6
[ 8.055539] NET: Registered protocol family 17
[ 8.064482] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 8.090313] 8021q: 802.1Q VLAN Support v1.8
[ 8.128116] Freeing unused kernel memory: 4896K
[ 8.137177] This architecture does not have kernel memory protection.
[ 8.150009] Run /init as init process
[ 8.676292] init: Console is alive
[ 8.683465] init: - watchdog -
[ 8.722285] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 8.814815] usbcore: registered new interface driver usbfs
[ 8.825942] usbcore: registered new interface driver hub
[ 8.836655] usbcore: registered new device driver usb
[ 8.902941] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 8.924880] SCSI subsystem initialized
[ 8.938440] fsl-ehci: Freescale EHCI Host controller driver
[ 8.951290] ehci-platform: EHCI generic platform driver
[ 8.972098] phy phy-usbphy.0: remote usb device wakeup disabled
[ 8.983904] phy phy-usbphy.0: UTMI 16bit 30MHz
[ 8.992764] ehci-platform 101c0000.ehci: EHCI Host Controller
[ 9.004254] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
[ 9.020169] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
[ 9.037306] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
[ 9.050916] hub 1-0:1.0: USB hub found
[ 9.058955] hub 1-0:1.0: 1 port detected
[ 9.072418] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 9.086565] ohci-platform: OHCI generic platform driver
[ 9.097378] ohci-platform 101c1000.ohci: Generic Platform OHCI controller
[ 9.110963] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
[ 9.126891] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
[ 9.164211] hub 2-0:1.0: USB hub found
[ 9.172278] hub 2-0:1.0: 1 port detected
[ 9.188784] usbcore: registered new interface driver usb-storage
[ 9.203558] usbcore: registered new interface driver uas
[ 9.215187] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 9.233771] init: - preinit -
[ 9.490811] random: jshn: uninitialized urandom read (4 bytes read)
[ 9.591029] random: jshn: uninitialized urandom read (4 bytes read)
[ 9.822843] random: jshn: uninitialized urandom read (4 bytes read)
[ 10.189196] 8021q: adding VLAN 0 to HW filter on device eth0
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 10.866132] mtk_soc_eth 10100000.ethernet eth0: port 4 link up (100Mbps/Full duplex)
[ 11.746694] procd: - early -
[ 11.752708] procd: - watchdog -
[ 12.263067] procd: - watchdog -
[ 12.269795] procd: - ubus -
[ 12.285038] random: ubusd: uninitialized urandom read (4 bytes read)
[ 12.308866] random: ubusd: uninitialized urandom read (4 bytes read)
[ 12.322215] random: ubusd: uninitialized urandom read (4 bytes read)
[ 12.339290] procd: - init -
Please press Enter to activate this console.
[ 13.057328] kmodloader: loading kernel modules from /etc/modules.d/*
[ 13.148727] fuse: init (API version 7.31)
[ 13.174028] Loading modules backported from Linux version v5.10.168-0-g707c48210a53
[ 13.189363] Backport generated by backports.git v5.10.168-1-0-gd990acb2
[ 13.277857] xt_time: kernel timezone is -0000
[ 13.442559] PPP generic driver version 2.4.2
[ 13.464470] NET: Registered protocol family 24
[ 13.481326] urngd: jent-rng init failed, err: 2
[ 13.535842] rt2800_wmac 10180000.wmac: loaded eeprom from mtd device "factory"
[ 13.550302] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 6352, rev 0500 detected
[ 13.565778] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 7620 detected
[ 13.615291] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 14.237414] random: jshn: uninitialized urandom read (4 bytes read)
[ 14.337742] random: jshn: uninitialized urandom read (4 bytes read)
[ 14.567382] random: jshn: uninitialized urandom read (4 bytes read)
[ 15.347269] random: dd: uninitialized urandom read (1 bytes read)
[ 19.620712] random: crng init done
[ 19.627510] random: 68 urandom warning(s) missed due to ratelimiting
BusyBox v1.33.2 (2023-01-06 16:34:46 UTC) built-in shell (ash)
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------------------------------
| |
| OpenWrt 21.02-SNAPSHOT, r16847-f8282da11e |
| |
| Build time: 2023-04-22 08:35 CEST |
| Cezary Jackiewicz, https://eko.one.pl |
| |
-----------------------------------------------------------------------------
| Machine: Nexx WT3020 (8M) |
| Uptime: 0d, 00:00:37 |
| Load: 0.62 0.16 0.05 |
| Flash: |
| Memory: total: 57.3MB, free: 48.9MB, used: 14% |
| Leases: 0 |
| lan: static, 192.168.1.1 |
| wan: dhcp, ? |
| wan6: dhcpv6, ? |
-----------------------------------------------------------------------------
=== WARNING! ================================================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.
-----------------------------------------------------------------------------
root@OpenWrt:/# [ 52.803833] 8021q: adding VLAN 0 to HW filter on device eth0
[ 52.840342] br-lan: port 1(eth0.1) entered blocking state
[ 52.851193] br-lan: port 1(eth0.1) entered disabled state
[ 52.862370] device eth0.1 entered promiscuous mode
[ 52.871975] device eth0 entered promiscuous mode
[ 52.957722] br-lan: port 1(eth0.1) entered blocking state
[ 52.968548] br-lan: port 1(eth0.1) entered forwarding state
[ 53.829255] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 59.935209] mtk_soc_eth 10100000.ethernet eth0: port 0 link up (100Mbps/Full duplex)
^C
root@OpenWrt:/# ping eko.one.pl
PING eko.one.pl (2.57.137.5): 56 data bytes
64 bytes from 2.57.137.5: seq=0 ttl=57 time=9.000 ms
64 bytes from 2.57.137.5: seq=1 ttl=57 time=10.220 ms
64 bytes from 2.57.137.5: seq=2 ttl=57 time=7.860 ms
^C
--- eko.one.pl ping statistics ---
3 packets transmitted, 3 packets received, 0% packet loss
round-trip min/avg/max = 7.860/9.026/10.220 ms
root@OpenWrt:/# wget -O /tmp/a.bin http://dl.eko.one.pl/openwrt-21.02/targets/ra
mips/mt7620/openwrt-21.02-snapshot-r16847-f8282da11e-ramips-mt7620-nexx_wt3020-8
m-squashfs-sysupgrade.bin
Downloading 'http://dl.eko.one.pl/openwrt-21.02/targets/ramips/mt7620/openwrt-21.02-snapshot-r16847-f8282da11e-ramips-mt7620-nexx_wt3020-8m-squashfs-sysupgrade.bin'
Connecting to 95.160.102.195:80
Writing to '/tmp/a.bin'
/tmp/a.bin 100% |*******************************| 6144k 0:00:00 ETA
Download completed (6291753 bytes)
root@OpenWrt:/# sysupgrade -n /tmp/a.bin
Sat Dec 28 17:02:40 CET 2024 upgrade: Commencing upgrade. Closing all shell sessions.
Watchdog handover: fd=3
- watchdog -
killall: telnetd: no process killed
Sat Dec 28 17:02:41 CET 2024 upgrade: Sending TERM to remaining processes ... logd hostapd wpa_supplicant netifd odhcpd ntpd dnsmasq ubusd
Sat Dec 28 17:02:44 CET 2024 upgrade: Sending KILL to remaining processes ...
[ 165.574086] sh (2383): drop_caches: 3
Sat Dec 28 17:02:45 CET 2024 upgrade: Switching to ramdisk...
Sat Dec 28 16:02:48 UTC 2024 upgrade: Performing system upgrade...
[ 168.121733] sh (2383): drop_caches: 3
Unlocking firmware ...
Writing from <stdin> to firmware ...
Sat Dec 28 16:03:54 UTC 2024 upgrade: Upgrade completed
Sat Dec 28 16:03:55 UTC 2024 upgrade: Rebooting system...
umount: can't unmount /dev: Resource [ 235.009417] reboot: Restarting system
busy
umount: can't unmount /tmp: Resource busy
U-Boot 1.1.3 (Jan 3 2014 - 09:12:42)
MAX Board: Ralink APSoC DRAM: 64 MB
relocate_code Pointer at: 83fb4000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
******************************
Software System Reset Occurred
******************************
spi_wait_nsec: 29
spi device id: ef 40 17 0 0 (40170000)
find flash: W25Q64BV
raspi_read: from:30000 len:1000
raspi_wait_ready: read_sr fail: e0
*** Warning - bad CRC, using default environment
============================================
Ralink UBoot Version: 4.1.1.0
--------------------------------------------
ASIC 7620_MP (Port5<->None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Jan 3 2014 Time:09:12:42
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768
##### The CPU freq = 580 MHZ ####
estimate memory size =64 Mbytes
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP. 0
3: System Boot system code via Flash.
## Booting image at bc050000 ...
raspi_read: from:50000 len:40
raspi_wait_ready: read_sr fail: e0
Bad Magic Number,00000000"Help me Obi-Wan Kenobi. You’re my only hope. " 
Odp: Nexx WT3020 nie działa po próbie wgrania Garygole
jak przez 2 wgram sysupgrade też jest to samo
"Help me Obi-Wan Kenobi. You’re my only hope. "
Odp: Nexx WT3020 nie działa po próbie wgrania Garygole
Uruchom initramfs i zobacz czy w partycji kernel w ogóle coś jest. Może flash mu poleciał i nic nie zapisuje w nim.
Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.
Odp: Nexx WT3020 nie działa po próbie wgrania Garygole
nie jestem pewien czy robię to dobrze, ale wychodzi mi coś takiego:
root@OpenWrt:/# cat /proc/mtd
dev: size erasesize name
mtd0: 00030000 00001000 "u-boot"
mtd1: 00010000 00001000 "u-boot-env"
mtd2: 00010000 00001000 "factory"
mtd3: 007b0000 00001000 "firmware"
mtd4: 001ea8b1 00001000 "kernel"
mtd5: 005c574f 00001000 "rootfs"
mtd6: 001ee000 00001000 "rootfs_data"
root@OpenWrt:/# ls /dev/mtd4
/dev/mtd4"Help me Obi-Wan Kenobi. You’re my only hope. "
Odp: Nexx WT3020 nie działa po próbie wgrania Garygole
hexdump -C /dev/mtd4
Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.
32 2024-12-28 18:41:37 (edytowany przez drk 2024-12-28 18:41:55)
Odp: Nexx WT3020 nie działa po próbie wgrania Garygole
wyciąłem zawartość między 0000200 a 0000320... czy potrzebna jest całość?
0000000 ' 005 031 V 246 n 027 362 d = F x \0 036 250 q
0000010 200 \0 \0 \0 200 \0 \0 \0 245 c 026 315 005 005 002 003
0000020 M I P S O p e n W r t L i n
0000030 u x - 5 . 4 . 2 3 8 \0 \0 \0 \0 \0 \0
0000040 m \0 \0 200 \0 306 374 _ \0 \0 \0 \0 \0 \0 \0 o
0000050 375 377 377 243 267 177 240 264 232 R K 346 332 200 222 g
0000060 , 202 345 320 0 320 " 203 203 232 ] 254 \t * 230 N
0000070 325 \f 5 322 313 V 331 > ~ 016 , 305 260 361 b
0000080 027 a & 334 207 3 ( 353 025 331 371 210 256 004 316
0000090 340 371 356 A 016 002 x 8 024 355 305 234 377 340 305
00000a0 & 241 243 200 244 y Z 253 \a 274 353 240 022 270 376 350
00000b0 312 = 274 + 027 : b 332 ) 363 306 o 364 366 225 316
00000c0 335 377 354 361 6 005 032 _ 273 306 350 e 367 023 G q
00000d0 l 365 g * 226 322 353 032 226 032 243 377 g S { 371
00000e0 p 024 252 315 B 262 235 310 232 220 212 004 317 245 334 F
00000f0 342 363 221 330 v ~ 310 < 227 262 Q 324 z Q k 003
0000100 220 T \r r & 003 254 253 377 \v 216 337 \b \t P
0000110 305 L 314 217 025 361 ) 313 T 273 306 $ 377 b > 016
0000120 204 D 345 Q l 264 254 254 262 r 350 370 b = 037 256
0000130 037 1 @ Y 364 \ 235 004 x 271 $ 220 035 267 263 %
0000140 U C 265 * 001 \0 p s H 311 l Z * " n }
0000150 335 210 v 230 B 347 Y 375 213 020 353 177 # 202 035 262
0000160 205 s 213 322 231 K = 203 s 020 321 \n 031 d \f 030
0000170 ! 362 = 207 . 215 321 G 313 277 334 240 n " 321 \b
0000180 | 306 G 266 033 J 253 q 206 u 024 200 y x 335 b
0000190 024 224 r 030 214 307 \b + 320 371 335 204 S d 245 .
00001a0 233 \f 367 237 233 \n * 221 234 245 304 021 021 274 300 \r
00001b0 321 347 / 230 346 247 331 \ 326 321 \n c 366 u 227
00001c0 303 @ 336 } T 1 331 245 [ 333 033 304 252 k @ \n
00001d0 326 ( 324 I r R 254 g 2 307 034 036 226 S 232 3
00001e0 S \f 201 210 246 036 G J X W N 203 200 [ 341 375
00001f0 341 254 334 240 036 E 313 275 212 037 257 1 \ = 345 037
0000200 f 033 374 350 364 321 i \f @ 252 177 + q b 4 270
0000320 206 { 260 237 _ d 314 360 355 \t B k k 226 i 351
0000330 304 " 303 252 234 6 025 \f 377 270 345 375 255 312 H 310
0000340 W 1 m U 235 8 215 177 231 274 214 016 264 177 _ 2
0000350 337 274 020 001 V 324 355 f \v ; 304 325 336 5 4 ~
0000360 : 306 303 334 0 177 Z 037 a 030 \n L 024 q N >
0000370 037 / 344 256 330 306 333 333 ^ W 275 034 320 213 031 236
0000380 + 1 177 324 r l b \b T \b 232 257 > 035 W 033
0000390 221 362 D 227 346 _ 322 256 | n 233 { 324 363 234 "
00003a0 364 242 214 375 \0 ~ 230 314 d 214 345 324 344 275 Y 210
00003b0 017 H _ M 276 310 Z 030 X 266 362 377 \t * c 016"Help me Obi-Wan Kenobi. You’re my only hope. "
Odp: Nexx WT3020 nie działa po próbie wgrania Garygole
Nie, jest normalnie zawartość
Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.
Odp: Nexx WT3020 nie działa po próbie wgrania Garygole
to co teraz?
"Help me Obi-Wan Kenobi. You’re my only hope. "
Odp: Nexx WT3020 nie działa po próbie wgrania Garygole
drk napisał/a:
to co teraz?
Ja bym się nieśmiało przypomniał, bo router mam na pająka podłączony 
wiem, że to stary sprzęt, ale akurat na taki mam zastosowanie (jako most bezprzewodowy).
"Help me Obi-Wan Kenobi. You’re my only hope. "
Odp: Nexx WT3020 nie działa po próbie wgrania Garygole
Zmień flash na inną sztukę?
Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.
Odp: Nexx WT3020 nie działa po próbie wgrania Garygole
żeby wylutować pamięć i wlutowałem następną? Tego nie potrafię i to dla mnie na poziomie lotów kosmicznych
A tak poważniej to jest jakiś programowy sposób, żeby sprawdzić, czy ten flash żyje?
"Help me Obi-Wan Kenobi. You’re my only hope. "
Odp: Nexx WT3020 nie działa po próbie wgrania Garygole
Teoretycznie żyje - jest wykrywany, ma zawartość sensowną itd.
Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.
Odp: Nexx WT3020 nie działa po próbie wgrania Garygole
Postanowiłem się dziś jeszcze pobawić tym routerem, za nim wyślę go do fajansu i właśnie odkryłem, że nie ważne co wgram (opcja 1) do pamięci RAM przez TFTP to zgłasza się OpenWRT 21.02 w Twoim wydaniu. Nie zauważyłem tego wcześniej, bo byłem zadowolony, że w ogóle coś ruszyło. Najpierw myślałem, że skopałem zmieniając nazwy, ale ściągnąłem obrazy jeszcze raz i zarówno Lede 17.01 jak i Openwrt 23.05 i za każdym razem zgłosił mi się Openwrt 21.02
Mifi 24.10 też zgłosiło się jako openwrt 21.02...
"Help me Obi-Wan Kenobi. You’re my only hope. "
Odp: Nexx WT3020 nie działa po próbie wgrania Garygole
Czyli uruchamia się to co jest we flash.
Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.
Odp: Nexx WT3020 nie działa po próbie wgrania Garygole
Zapewne tak, ale router sam z siebie się nadal nie uruchamia.
Ten błąd o który pytałem jak trochę poguglowałem to wygląda jak błąd bootloadera. Czy możliwe jest, że "sam" uszkodził się bootloader? Można taki bootloader jeszcze raz wgrać? Znalazłem na forum openwrt link do jakiegoś hackpascals. W menu jest opcja 9 'Load Boot Loader code then write to Flash via TFTP' tym się to robi?
"Help me Obi-Wan Kenobi. You’re my only hope. "
Odp: Nexx WT3020 nie działa po próbie wgrania Garygole
To breed. Zapomnij o tym, zamknięty soft i sprawia problemy przy wgrywaniu openwrt.
Możesz przez 4 wejść do bootloadera i tam ręcznie zrobić upgrade czego chcesz, pod warunkiem że będzie chciało się zapisać do flash. Na początek zdobądź bootloader, niech ktoś kto ma wt3020 podeście ci go, później możesz wgrać i sprawdzisz czy się w ogóle uruchamia. Jeżeli tak to leć z softem.
Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.
Posty: 26 do 42 z 42
Strony Poprzednia 1 2
Zaloguj się lub zarejestruj by napisać odpowiedź
eko.one.pl → Oprogramowanie / Software → Nexx WT3020 nie działa po próbie wgrania Garygole
Forum oparte o PunBB, wspierane przez Informer Technologies, Inc