Nie jesteś zalogowany. Proszę się zalogować lub zarejestrować.
eko.one.pl → Sprzęt / Hardware → ZTE MF286R - OpenWrt
Strony Poprzednia 1 … 45 46 47 48 49 50 Następna
Zaloguj się lub zarejestruj by napisać odpowiedź
Wszystkie nie. 11/12/13 (web, kernel, rootfs). Jeżeli mtdx nie będzie chciał ruszyć - użyj mtdblockX. Jeżeli partycja będzie tylko do odczytu - użyj mtd-rw (https://github.com/jclehner/mtd-rw - jest to w openwrt)
Dzięki za info
Weż z 22.05 i zobacz czy się uruchomi: https://dl.eko.one.pl/firmware/?version … zte_mf286r
poszło, aktualnie jest OpenWrt 24.10 luci
skonfigurowałem według informacji, które tu znalazłem, ale modem nie działa "Urządzenie sieciowe nie jest obecne"
mam podejrzenie, że może być uwalony
działał jakiś czas na oryginalnym sofcie, samoczynnie się zresetował i już nie wstał
mogę jakoś na szybko sprawdzić czy jest sprawny?
Zaloguj się przez ssh i pokaż wyniki poleceń
uci show network
ifstatus wwan
cat /sys/kernel/debug/usb/devicesuci show network
network.loopback=interface
network.loopback.device='lo'
network.loopback.proto='static'
network.loopback.ipaddr='127.0.0.1'
network.loopback.netmask='255.0.0.0'
network.globals=globals
network.globals.ula_prefix='fd3a:f12b:4412::/48'
network.@device[0]=device
network.@device[0].name='br-lan'
network.@device[0].type='bridge'
network.@device[0].ports='eth0.1'
network.lan=interface
network.lan.device='br-lan'
network.lan.proto='static'
network.lan.ipaddr='192.168.1.1'
network.lan.netmask='255.255.255.0'
network.lan.ip6assign='60'
network.@switch[0]=switch
network.@switch[0].name='switch0'
network.@switch[0].reset='1'
network.@switch[0].enable_vlan='1'
network.@switch_vlan[0]=switch_vlan
network.@switch_vlan[0].device='switch0'
network.@switch_vlan[0].vlan='1'
network.@switch_vlan[0].ports='1 2 3 5 0t'
network.wwan=interface
network.wwan.proto='ncm'
network.wwan.device='/dev/ttyACM0'
network.wwan.pdptype='IP'
network.wwan.apn='internet'
network.wwan.ipv6='auto'
network.wwan.delay='60'cat /sys/kernel/debug/usb/devices
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 1
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0002 Rev= 6.06
S: Manufacturer=Linux 6.6.63 ehci_hcd
S: Product=EHCI Host Controller
S: SerialNumber=1b000000.usb
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 1
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0002 Rev= 6.06
S: Manufacturer=Linux 6.6.63 ehci_hcd
S: Product=EHCI Host Controller
S: SerialNumber=1b400000.usb
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256msifstatus wwan
{
"up": false,
"pending": false,
"available": true,
"autostart": true,
"dynamic": false,
"proto": "ncm",
"data": {
}
}Tak, w ogóle nie widzi ci modemu jako urządzenia na magistrali usb. Nie ma go jak by fizycznie nie był podłączony.
wsadziłem na próbę jakiś inny
tego widzi
cat /sys/kernel/debug/usb/devices
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 1
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0002 Rev= 6.06
S: Manufacturer=Linux 6.6.63 ehci_hcd
S: Product=EHCI Host Controller
S: SerialNumber=1b000000.usb
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=02(comm.) Sub=00 Prot=00 MxPS=64 #Cfgs= 2
P: Vendor=0bdb ProdID=1900 Rev= 0.00
S: Manufacturer=Ericsson
S: Product=Ericsson F3507g Mobile Broadband Minicard Composite Device
S: SerialNumber=3541430203654660
C:* #Ifs=11 Cfg#= 1 Atr=e0 MxPwr= 20mA
I:* If#= 0 Alt= 0 #EPs= 0 Cls=02(comm.) Sub=08 Prot=00 Driver=(none)
I:* If#= 1 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=02 Prot=01 Driver=cdc_acm
E: Ad=8a(I) Atr=03(Int.) MxPS= 16 Ivl=16ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_acm
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=02 Prot=01 Driver=cdc_acm
E: Ad=89(I) Atr=03(Int.) MxPS= 16 Ivl=16ms
I:* If#= 4 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_acm
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=09 Prot=01 Driver=cdc_wdm
E: Ad=8b(I) Atr=03(Int.) MxPS= 16 Ivl=16ms
I:* If#= 6 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=09 Prot=01 Driver=cdc_wdm
E: Ad=8c(I) Atr=03(Int.) MxPS= 16 Ivl=16ms
I:* If#= 7 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=0a Prot=00 Driver=cdc_ether
E: Ad=87(I) Atr=03(Int.) MxPS= 8 Ivl=8ms
I: If#= 8 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
I:* If#= 8 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 8 Alt= 2 #EPs= 2 Cls=0a(data ) Sub=00 Prot=ee Driver=cdc_ether
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 9 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=02 Prot=01 Driver=cdc_acm
E: Ad=85(I) Atr=03(Int.) MxPS= 16 Ivl=16ms
I:* If#=10 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_acm
E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
C: #Ifs= 9 Cfg#= 2 Atr=e0 MxPwr= 20mA
I: If#= 0 Alt= 0 #EPs= 0 Cls=02(comm.) Sub=08 Prot=00 Driver=
I: If#= 1 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=02 Prot=01 Driver=
E: Ad=8a(I) Atr=03(Int.) MxPS= 16 Ivl=16ms
I: If#= 2 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 3 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=02 Prot=01 Driver=
E: Ad=89(I) Atr=03(Int.) MxPS= 16 Ivl=16ms
I: If#= 4 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 5 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=09 Prot=01 Driver=
E: Ad=8b(I) Atr=03(Int.) MxPS= 16 Ivl=16ms
I: If#= 6 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=09 Prot=01 Driver=
E: Ad=8c(I) Atr=03(Int.) MxPS= 16 Ivl=16ms
I: If#= 7 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=0a Prot=00 Driver=
E: Ad=87(I) Atr=03(Int.) MxPS= 8 Ivl=8ms
I: If#= 8 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=00 Driver=
I: If#= 8 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 8 Alt= 2 #EPs= 2 Cls=0a(data ) Sub=00 Prot=ee Driver=
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 1
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0002 Rev= 6.06
S: Manufacturer=Linux 6.6.63 ehci_hcd
S: Product=EHCI Host Controller
S: SerialNumber=1b400000.usb
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256msmyślisz, że da się go tu skonfigurować?
Po co , jak to modem 3G jest... Szkoda prądu na niego...
Fizycznie pewnie tak, jakimiś poleceniami AT, tylko faktycznie po co.
chyba sztuka dla sztuki 
jest szansa gdzieś kupić taki modem, czy tylko z odzysku?
Od MF286R? Tylko z odzysku, byt nie istnieje w realnym świecie.
taki, żeby zadziałał z MF286R
Z OpenWRT zadziała pewnie każdy na mPCIe .
O modemy Cat.6 czy CAT.7 trudno na tym złączu( z agregacją dwóch pasm) , nie mówiąc już o CAT.12( QAM256 MIMO4x4) ,czy wyższych...
Przy okazji jakby ktoś wiedział jaki modem mPCIe ( może być CAT.3) działa na Windowsie ?
Quectele. Dają sterowniki do windows.
Firmware: https://drive.google.com/file/d/1XyW9Mf … g4iMJ/view
T-Mobile
CR_TMOPLMF286RV1.0.1.B04
MF286-1.0
Witam jestem nowy i nie wiem czy w dobrym miejscu pisze Chce kupić https://www.olx.pl/d/oferta/router-na-k … 26ZoO.html
Czy ktoś mog.by mi pomóc w wgraniu openwrt.
Dziękuję
Weź dołóż do MF286D , to zupełnie inna klasa. Sam router ma lepszy procesor , a i modem już cat12 ( zamiast 7)..
Jak coś to mogę Ci za 200PLN wystawić mój MF286D z już wgranym openwrt
Weź dołóż do MF286D , to zupełnie inna klasa. Sam router ma lepszy procesor , a i modem już cat12 ( zamiast 7)..
Jak coś to mogę Ci za 200PLN wystawić mój MF286D z już wgranym openwrt
dopiero teraz zobaczyłem ze odpisałeś
wysłałem maila na prv
Właśnie zaryzykowałem update z zachowaniem ustawień i wan już nie wstaje. W kółko szuka modemu
Thu Jan 23 00:43:53 2025 user.notice firewall: Reloading firewall due to ifup of lan (br-lan)
' does not exist or is not an array/objectifd: wan (2772): WARNING: Variable '
Thu Jan 23 00:43:54 2025 daemon.notice netifd: wan (2772): Unsupported modem
Thu Jan 23 00:43:55 2025 daemon.notice netifd: wan (3044): Stopping network wanOby to tylko literówka.
root@gate2:/etc/config# dmesg
[ 0.000000] Linux version 6.6.71 (cezary@eko.one.pl) (mips-openwrt-linux-musl-gcc (OpenWrt GCC 13.3.0 r28010-49d8f4b833) 13.3.0, GNU ld (GNU Binutils) 2.42) #0 Sun Jan 19 10:17:23 2025
[ 0.000000] printk: bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019750 (MIPS 74Kc)
[ 0.000000] MIPS: machine is ZTE MF286R
[ 0.000000] SoC: Qualcomm Atheros QCA956X ver 1 rev 0
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Kernel command line: console=ttyS0,115200n8 rootfstype=squashfs,jffs2
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32480
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 119064K/131072K available (7660K kernel code, 592K rwdata, 964K rodata, 1208K init, 240K bss, 12008K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 51
[ 0.000000] CPU clock: 775.000 MHz
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4932285024 ns
[ 0.000001] sched_clock: 32 bits at 388MHz, resolution 2ns, wraps every 5541893118ns
[ 0.008305] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[ 0.074798] pid_max: default: 32768 minimum: 301
[ 0.089098] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.096833] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.113366] RCU Tasks Trace: Setting shift to 0 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=1.
[ 0.127883] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.138305] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[ 0.147960] pinctrl core: initialized pinctrl subsystem
[ 0.156580] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.163345] thermal_sys: Registered thermal governor 'step_wise'
[ 0.165367] /ahb/apb: Fixed dependency cycle(s) with /ahb/apb/interrupt-controller@18060010
[ 0.193054] clocksource: Switched to clocksource MIPS
[ 0.208585] NET: Registered PF_INET protocol family
[ 0.214008] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.222993] tcp_listen_portaddr_hash hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.231969] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.240149] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.248242] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear)
[ 0.255717] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.263163] MPTCP token hash table entries: 512 (order: 0, 6144 bytes, linear)
[ 0.271012] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.277952] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.286201] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.292219] PCI: CLS 0 bytes, default 32
[ 0.300943] workingset: timestamp_bits=14 max_order=15 bucket_order=1
[ 0.309367] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.315569] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.333101] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 0.344268] pinctrl-single 1804002c.pinmux: 544 pins, size 68
[ 0.351753] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.363799] printk: console [ttyS0] disabled
[ 0.368780] 18020000.uart: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 1562500) is a 16550A
[ 0.378049] printk: console [ttyS0] enabled
[ 0.387117] printk: bootconsole [early0] disabled
[ 0.432502] spi-nor spi0.0: gd25q16 (2048 Kbytes)
[ 0.437523] 3 fixed-partitions partitions found on MTD device spi0.0
[ 0.444112] Creating 3 MTD partitions on "spi0.0":
[ 0.449066] 0x000000000000-0x0000000a0000 : "u-boot"
[ 0.456933] 0x0000000a0000-0x0000000c0000 : "u-boot-env"
[ 0.464454] 0x0000000c0000-0x000000200000 : "reserved1"
[ 0.473823] spi-nand spi0.1: GigaDevice SPI NAND was found.
[ 0.479600] spi-nand spi0.1: 128 MiB, block size: 128 KiB, page size: 2048, OOB size: 128
[ 0.488192] 6 fixed-partitions partitions found on MTD device (null)
[ 0.494790] Creating 6 MTD partitions on "(null)":
[ 0.499744] 0x000000000000-0x0000000a0000 : "fota-flag"
[ 0.510913] 0x0000000a0000-0x000000120000 : "art"
[ 0.518524] OF: Bad cell count for /ahb/spi@1f000000/flash@1/partitions
[ 0.525748] 0x000000120000-0x0000001a0000 : "mac"
[ 0.533914] OF: Bad cell count for /ahb/spi@1f000000/flash@1/partitions
[ 0.541031] 0x0000001a0000-0x000001800000 : "ubiconcat0"
[ 0.576118] 0x000001800000-0x000001c00000 : "kernel"
[ 0.588106] 0x000001c00000-0x000008000000 : "ubiconcat1"
[ 1.417498] switch0: Atheros AR8337 rev. 2 switch registered on mdio.0
[ 2.074792] ag71xx-legacy 19000000.eth: connected to PHY at mdio.0:00 [uid=004dd036, driver=Atheros AR8216/AR8236/AR8316]
[ 2.086894] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode: sgmii
[ 2.096940] NET: Registered PF_INET6 protocol family
[ 2.113130] Segment Routing with IPv6
[ 2.117006] In-situ OAM (IOAM) with IPv6
[ 2.121208] NET: Registered PF_PACKET protocol family
[ 2.126513] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 2.140196] 8021q: 802.1Q VLAN Support v1.8
[ 2.184215] PCI host bridge to bus 0000:00
[ 2.188473] pci_bus 0000:00: root bus resource [mem 0x12000000-0x13ffffff]
[ 2.195637] pci_bus 0000:00: root bus resource [io 0x0000]
[ 2.201397] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 2.209641] pci 0000:00:00.0: [168c:0056] type 00 class 0x028000
[ 2.215893] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[ 2.223030] pci 0000:00:00.0: PME# supported from D0 D3hot
[ 2.229866] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[ 2.236770] pci 0000:00:00.0: BAR 0: assigned [mem 0x12000000-0x121fffff 64bit]
[ 2.244719] Concatenating MTD devices:
[ 2.248607] (0): "ubiconcat0"
[ 2.251669] (1): "ubiconcat1"
[ 2.254770] into device "ubi-concat"
[ 2.258493] 1 fixed-partitions partitions found on MTD device ubi-concat
[ 2.265426] Creating 1 MTD partitions on "ubi-concat":
[ 2.270741] 0x000000000000-0x000007a60000 : "ubi"
[ 2.282697] UBI: auto-attach mtd9
[ 2.286184] ubi0: attaching mtd9
[ 4.953268] ubi0: scanning is finished
[ 4.991498] ubi0: attached mtd9 (name "ubi", size 122 MiB)
[ 4.997235] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 5.004352] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 5.011366] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 5.018561] ubi0: good PEBs: 976, bad PEBs: 3, corrupted PEBs: 0
[ 5.024770] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[ 5.032225] ubi0: max/mean erase counter: 34/20, WL threshold: 4096, image sequence number: 1447625496
[ 5.041850] ubi0: available PEBs: 0, total reserved PEBs: 976, PEBs reserved for bad PEB handling: 17
[ 5.051468] ubi0: background thread "ubi_bgt0d" started, PID 312
[ 5.060153] block ubiblock0_0: created from ubi0:0(rootfs)
[ 5.065881] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
[ 5.073286] clk: Disabling unused clocks
[ 5.097476] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[ 5.111317] Freeing unused kernel image (initmem) memory: 1208K
[ 5.117468] This architecture does not have kernel memory protection.
[ 5.124139] Run /sbin/init as init process
[ 5.128367] with arguments:
[ 5.128372] /sbin/init
[ 5.128377] with environment:
[ 5.128382] HOME=/
[ 5.128387] TERM=linux
[ 5.938585] init: Console is alive
[ 5.942478] init: - watchdog -
[ 7.952301] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 8.057070] usbcore: registered new interface driver usbfs
[ 8.062814] usbcore: registered new interface driver hub
[ 8.068461] usbcore: registered new device driver usb
[ 8.083387] gpio_button_hotplug: loading out-of-tree module taints kernel.
[ 8.102462] ehci-platform 1b000000.usb: EHCI Host Controller
[ 8.108403] ehci-platform 1b000000.usb: new USB bus registered, assigned bus number 1
[ 8.116656] ehci-platform 1b000000.usb: irq 15, io mem 0x1b000000
[ 8.123364] ehci-platform 1b400000.usb: EHCI Host Controller
[ 8.129243] ehci-platform 1b400000.usb: new USB bus registered, assigned bus number 2
[ 8.137528] ehci-platform 1b400000.usb: irq 16, io mem 0x1b400000
[ 8.145248] ehci-platform 1b000000.usb: USB 2.0 started, EHCI 1.00
[ 8.152509] hub 1-0:1.0: USB hub found
[ 8.157317] hub 1-0:1.0: 1 port detected
[ 8.193073] ehci-platform 1b400000.usb: USB 2.0 started, EHCI 1.00
[ 8.200747] hub 2-0:1.0: USB hub found
[ 8.205217] hub 2-0:1.0: 1 port detected
[ 8.214442] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 8.233586] init: - preinit -
[ 8.533264] usb 1-1: new high-speed USB device number 2 using ehci-platform
[ 9.453124] random: crng init done
[ 12.253760] Atheros AR8216/AR8236/AR8316 mdio.0:00: Port 5 is up
[ 12.261523] eth0: link up (1000Mbps/Full duplex)
[ 16.581735] UBIFS (ubi0:1): Mounting in unauthenticated mode
[ 16.587904] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 512
[ 16.767744] UBIFS (ubi0:1): recovery needed
[ 17.191416] UBIFS (ubi0:1): recovery completed
[ 17.196161] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[ 17.204271] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 17.214520] UBIFS (ubi0:1): FS size: 113897472 bytes (108 MiB, 897 LEBs), max 908 LEBs, journal size 5713920 bytes (5 MiB, 45 LEBs)
[ 17.226749] UBIFS (ubi0:1): reserved for root: 4952683 bytes (4836 KiB)
[ 17.233585] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID B4E9E846-2667-42B3-89CF-08237753DBA7, small LPT model
[ 17.269116] mount_root: switching to ubifs overlay
[ 17.332797] urandom-seed: Seeding with /etc/urandom.seed
[ 17.462934] eth0: link down
[ 17.495133] procd: - early -
[ 17.498429] procd: - watchdog -
[ 18.373276] procd: - watchdog -
[ 18.394723] procd: - ubus -
[ 18.595591] procd: - init -
[ 21.998310] kmodloader: loading kernel modules from /etc/modules.d/*
[ 23.479971] NET: Registered PF_ALG protocol family
[ 23.566188] OpenVPN data channel offload (ovpn-dco) 2.0.0 -- (C) 2020-2023 OpenVPN, Inc.
[ 23.616960] tun: Universal TUN/TAP device driver, 1.6
[ 23.659930] gre: GRE over IPv4 demultiplexor driver
[ 23.705082] ip_gre: GRE over IPv4 tunneling driver
[ 23.863331] cdc_acm 1-1:1.2: ttyACM0: USB ACM device
[ 23.868650] usbcore: registered new interface driver cdc_acm
[ 23.874546] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 23.945813] usbcore: registered new interface driver cdc_wdm
[ 23.985526] Loading modules backported from Linux version v6.12.6-0-ge9d65b48ce1a
[ 23.993318] Backport generated by backports.git v6.1.110-1-35-g410656ef04d2
[ 24.083446] urngd: v1.0.2 started.
[ 24.157031] usbcore: registered new interface driver usbserial_generic
[ 24.163917] usbserial: USB Serial support registered for generic
[ 24.220898] usbcore: registered new interface driver cdc_ether
[ 24.265835] usbcore: registered new interface driver cdc_ncm
[ 24.414562] usbcore: registered new interface driver huawei_cdc_ncm
[ 25.266848] PPP generic driver version 2.4.2
[ 25.294217] PPP MPPE Compression module registered
[ 25.325380] NET: Registered PF_PPPOX protocol family
[ 25.354529] PPTP driver version 0.8.5
[ 25.376296] usbcore: registered new interface driver qmi_wwan
[ 25.471141] rndis_host 1-1:1.0 eth1: register 'rndis_host' at usb-1b000000.usb-1, ZTE RNDIS device, 0a:7e:74:fd:34:82
[ 25.482432] usbcore: registered new interface driver rndis_host
[ 25.533667] usbcore: registered new interface driver sierra
[ 25.539509] usbserial: USB Serial support registered for Sierra USB modem
[ 25.605515] usbcore: registered new interface driver sierra_net
[ 25.650789] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information.
[ 25.658935] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
[ 25.860147] ath10k 6.10 driver, optimized for CT firmware, probing pci device: 0x56.
[ 25.935578] ath10k_pci 0000:00:00.0: enabling device (0000 -> 0002)
[ 25.942383] ath10k_pci 0000:00:00.0: pci irq legacy oper_irq_mode 1 irq_mode 0 reset_mode 0
[ 30.614213] ath10k_pci 0000:00:00.0: qca9888 hw2.0 target 0x01000000 chip_id 0x00000000 sub 0000:0000
[ 30.623795] ath10k_pci 0000:00:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[ 30.638286] ath10k_pci 0000:00:00.0: firmware ver 10.4b-ct-9888-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 59e741e7
[ 30.991709] ath10k_pci 0000:00:00.0: board_file api 2 bmi_id 0:16 crc32 5968d47d
[ 32.767477] ath10k_pci 0000:00:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
[ 32.775291] ath10k_pci 0000:00:00.0: msdu-desc: 2500 skid: 32
[ 32.825231] ath10k_pci 0000:00:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'
[ 32.836548] ath10k_pci 0000:00:00.0: wmi print 'free: 114572 iram: 12644 sram: 29508'
[ 33.072523] ath10k_pci 0000:00:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-nvmem max-sta 32 raw 0 hwcrypto 1
[ 33.176579] ath: EEPROM regdomain: 0x0
[ 33.176603] ath: EEPROM indicates default country code should be used
[ 33.176609] ath: doing EEPROM country->regdmn map search
[ 33.176624] ath: country maps to regdmn code: 0x3a
[ 33.176631] ath: Country alpha2 being used: US
[ 33.176639] ath: Regpair used: 0x3a
[ 33.252171] usbcore: registered new interface driver cdc_mbim
[ 33.278602] usbcore: registered new interface driver option
[ 33.284502] usbserial: USB Serial support registered for GSM modem (1-port)
[ 33.312936] usbcore: registered new interface driver qcserial
[ 33.319020] usbserial: USB Serial support registered for Qualcomm USB modem
[ 33.381063] ath: EEPROM regdomain: 0x0
[ 33.381089] ath: EEPROM indicates default country code should be used
[ 33.381096] ath: doing EEPROM country->regdmn map search
[ 33.381110] ath: country maps to regdmn code: 0x3a
[ 33.381117] ath: Country alpha2 being used: US
[ 33.381124] ath: Regpair used: 0x3a
[ 33.392978] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
[ 33.393967] ieee80211 phy1: Atheros AR9561 Rev:0 mem=0xed2eabf2, irq=2
[ 33.423565] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 51.680284] export_store: invalid GPIO 20
[ 54.049047] eth0: link up (1000Mbps/Full duplex)
[ 54.058291] br-lan: port 1(eth0.1) entered blocking state
[ 54.063954] br-lan: port 1(eth0.1) entered disabled state
[ 54.069570] eth0.1: entered allmulticast mode
[ 54.074099] ag71xx-legacy 19000000.eth eth0: entered allmulticast mode
[ 54.081079] eth0.1: entered promiscuous mode
[ 54.085545] ag71xx-legacy 19000000.eth eth0: entered promiscuous mode
[ 54.145386] br-lan: port 1(eth0.1) entered blocking state
[ 54.150987] br-lan: port 1(eth0.1) entered forwarding stateNie czyta jego producenta. Pokaż wynik
gcom -d /dev/ttyACM0 -s /etc/gcom/getcardinfo.gcom
Nie czyta jego producenta. Pokaż wynik
gcom -d /dev/ttyACM0 -s /etc/gcom/getcardinfo.gcom
root@gate2:~# gcom -d /dev/ttyACM0 -s /etc/gcom/getcardinfo.gcom
+CGMI: "Marvell"Czyta poprawnie. Zrestartuj go i zobacz czy złapie ew zmień sobie w /lib/netifd/proto/ncm.sh i podstaw na stałe tego marvella żeby nie było problemu z czytaniem.
Czyta poprawnie. Zrestartuj go i zobacz czy złapie ew zmień sobie w /lib/netifd/proto/ncm.sh i podstaw na stałe tego marvella żeby nie było problemu z czytaniem.
zahaszowałem tam wyjscie ze skryptu, idzie zatem dalej lecz i tak nic się nie zmienia. Dla marvella przepisalem init recznie do konsoli. Czy te polecenia nie powinny wypluć przynajmniej 'OK' ??
...
json_load "$(cat /etc/gcom/ncm.json)"
json_select "$manufacturer"
[ $? -ne 0 ] && {
echo "Unsupported modem"
proto_notify_error "$interface" UNSUPPORTED_MODEM
proto_set_available "$interface" 0
# return 1
}
...
root@gate2:~# sms_tool -d /dev/ttyACM0 at 'AT+CFUN=1'
root@gate2:~# sms_tool -d /dev/ttyACM0 at "AT+SPTZCMD=\\\"Y29ubm1hbmN0bCBuZGlzZGlhbCBBVF5ORElTRFVOPSJ1c2IwIiwxLDE=\\\""Nie tu. Chwilę wyżej masz odczytywane manufacturer poleceniem które ja podałem. Zamień je na
manufacturer="\"marvell\""
Nie tu. Chwilę wyżej masz odczytywane manufacturer poleceniem które ja podałem. Zamień je na
manufacturer="\"marvell\""
Poszło dalej, jednak wróciła sytuacja sprzed paru aktualizacji, czyli czeka w nieskończoność na IP przy ustawieniu "Wg ustawień modemu" albo nie toleruje "option mode 'auto'" przy ustawieniu 5G/4G/3G/2G.
Sun Jan 19 11:27:48 2025 daemon.notice netifd: wan_4 (10724): udhcpc: started, v1.36.1
Sun Jan 19 11:27:49 2025 daemon.notice netifd: wan_4 (10724): udhcpc: broadcasting discover
Sun Jan 19 11:27:52 2025 daemon.notice netifd: wan_4 (10724): udhcpc: broadcasting discover
Sun Jan 19 11:27:55 2025 daemon.notice netifd: wan_4 (10724): udhcpc: broadcasting discover
...|||||...
Sun Jan 19 11:32:10 2025 daemon.notice netifd: wan (14345): WARNING: Variable 'modes' does not exist or is not an array/objectRestartów wiele, czekania parę godzin...
Rozumiem, że nie mogę wrócić do poprzedniej wersji. Żałuję że nie zrzuciłem dmesg tamtej wersji żeby porównać z nim obecny. Coś musi być inaczej już przy uruchamianiu pierwszych procesów.
Nie ma modes dla tego modelu. Poprzednia wersja nic by ci nie działa, bo kod od ncm w ogóle nic się nie zmienił. Możesz 23.05 wgrać i zobaczyć.
Strony Poprzednia 1 … 45 46 47 48 49 50 Następna
Zaloguj się lub zarejestruj by napisać odpowiedź
eko.one.pl → Sprzęt / Hardware → ZTE MF286R - OpenWrt
Forum oparte o PunBB, wspierane przez Informer Technologies, Inc