Nie jesteś zalogowany. Proszę się zalogować lub zarejestrować.
eko.one.pl → Sprzęt / Hardware → ZTE MF286R - OpenWrt
Strony Poprzednia 1 … 43 44 45 46 47 … 50 Następna
Zaloguj się lub zarejestruj by napisać odpowiedź
Te cztery pierwsze są zbędne jeżeli korzystasz tylko z luci.
Dzień Dobry.
Coś się popsuło w tym routerze lub w Orange Flex(?) . Router działał na działce od rodziców w czerwcu bez problemu, dzisiaj przychodzę i nie mam internetu.
Interfejs pokazuje: "Error: Network device is not present"
Zobaczyłem logi:
Sun Aug 25 19:56:52 2024 daemon.notice netifd: lte (3090): sending -> AT+CFUN=1
Sun Aug 25 19:56:52 2024 daemon.notice netifd: lte (3090): Configuring modem
Sun Aug 25 19:56:53 2024 daemon.notice netifd: lte (3090): sending -> AT+ZGDCONT=1,"IP","internet","",0,0
Sun Aug 25 19:56:58 2024 daemon.notice netifd: lte (3090): Error running AT-command
Sun Aug 25 19:56:58 2024 daemon.notice netifd: lte (3090): Failed to configure modem
Sun Aug 25 19:56:58 2024 daemon.notice netifd: lte (3282): Stopping network lte
Sun Aug 25 19:57:00 2024 daemon.notice netifd: lte (3282): sending -> AT+ZGACT=0,1
Sun Aug 25 19:57:03 2024 daemon.notice netifd: Interface 'lte' is now down
Sun Aug 25 19:57:03 2024 daemon.notice netifd: Interface 'lte' is setting up now
Sun Aug 25 19:57:04 2024 daemon.warn odhcpd[1702]: No default route present, overriding ra_lifetime!
Sun Aug 25 19:57:11 2024 daemon.notice netifd: lte (3294): sending -> AT+CFUN=1
Sun Aug 25 19:57:11 2024 daemon.notice netifd: lte (3294): Configuring modem
Sun Aug 25 19:57:12 2024 daemon.notice netifd: lte (3294): sending -> AT+ZGDCONT=1,"IP","internet","",0,0
Sun Aug 25 19:57:16 2024 daemon.notice netifd: lte (3294): Error running AT-command
Sun Aug 25 19:57:16 2024 daemon.notice netifd: lte (3294): Failed to configure modem
Sun Aug 25 19:57:17 2024 daemon.notice netifd: lte (3412): Stopping network lte
Sun Aug 25 19:57:19 2024 daemon.notice netifd: lte (3412): sending -> AT+ZGACT=0,1
Sun Aug 25 19:57:21 2024 daemon.notice netifd: Interface 'lte' is now down
Sun Aug 25 19:57:21 2024 daemon.notice netifd: Interface 'lte' is setting up now
Sun Aug 25 19:57:22 2024 daemon.warn odhcpd[1702]: No default route present, overriding ra_lifetime!
Sun Aug 25 19:57:27 2024 daemon.notice netifd: lte (3424): sending -> AT+CFUN=1
Sun Aug 25 19:57:27 2024 daemon.notice netifd: lte (3424): Configuring modem
Sun Aug 25 19:57:28 2024 daemon.notice netifd: lte (3424): sending -> AT+ZGDCONT=1,"IP","internet","",0,0
Sun Aug 25 19:57:31 2024 daemon.info hostapd: phy0-ap0: STA 5c:e9:1e:69:04:7e IEEE 802.11: authenticated
Sun Aug 25 19:57:31 2024 daemon.info hostapd: phy0-ap0: STA 5c:e9:1e:69:04:7e IEEE 802.11: associated (aid 1)
Sun Aug 25 19:57:31 2024 daemon.notice hostapd: phy0-ap0: AP-STA-CONNECTED 5c:e9:1e:69:04:7e auth_alg=open
Sun Aug 25 19:57:31 2024 daemon.info hostapd: phy0-ap0: STA 5c:e9:1e:69:04:7e WPA: pairwise key handshake completed (RSN)
Sun Aug 25 19:57:31 2024 daemon.notice hostapd: phy0-ap0: EAPOL-4WAY-HS-COMPLETED 5c:e9:1e:69:04:7e
Sun Aug 25 19:57:31 2024 daemon.warn odhcpd[1702]: No default route present, overriding ra_lifetime!
Sun Aug 25 19:57:31 2024 daemon.info dnsmasq-dhcp[1]: DHCPREQUEST(br-lan) 192.168.10.106 5c:e9:1e:69:04:7e
Sun Aug 25 19:57:31 2024 daemon.info dnsmasq-dhcp[1]: DHCPACK(br-lan) 192.168.10.106 5c:e9:1e:69:04:7e NonameMook14Pro
Sun Aug 25 19:57:32 2024 daemon.notice netifd: lte (3424): Error running AT-command
Sun Aug 25 19:57:32 2024 daemon.notice netifd: lte (3424): Failed to configure modem
Sun Aug 25 19:57:32 2024 daemon.notice netifd: lte (3537): Stopping network lte
Sun Aug 25 19:57:35 2024 daemon.notice netifd: lte (3537): sending -> AT+ZGACT=0,1
Sun Aug 25 19:57:36 2024 daemon.warn odhcpd[1702]: No default route present, overriding ra_lifetime!
Sun Aug 25 19:57:37 2024 daemon.notice netifd: Interface 'lte' is now down
Sun Aug 25 19:57:37 2024 daemon.notice netifd: Interface 'lte' is setting up now
Sun Aug 25 19:57:38 2024 daemon.warn odhcpd[1702]: No default route present, overriding ra_lifetime!
Sun Aug 25 19:57:40 2024 daemon.notice netifd: lte (3549): WARNING: Variable 'or' does not exist or is not an array/object
Sun Aug 25 19:57:40 2024 daemon.notice netifd: lte (3549): Unsupported modem
Sun Aug 25 19:57:40 2024 daemon.notice netifd: lte (3658): Stopping network lte
Sun Aug 25 19:57:40 2024 daemon.warn odhcpd[1702]: No default route present, overriding ra_lifetime!
Sun Aug 25 19:57:43 2024 daemon.notice netifd: lte (3658): sending -> AT+ZGACT=0,1
Sun Aug 25 19:57:45 2024 daemon.notice netifd: Interface 'lte' is now downOk, czyli modem wysyła komendę
AT+ZGDCONT=1,"IP","internet","",0,0i komenda się wysypuje.
Moje ustawienie interfejsu:
config interface 'lte'
option delay '15'
option proto 'ncm'
option device '/dev/ttyACM0'
option apn 'internet'
option auth 'pap'
option username 'internet'
option password 'internet'Czyli tak jak tutaj: https://www.orange.pl/omnibook/konfigur … -telefonie
Nazwa konfiguracji: Internet IPv4
APN (punkt dostępu): internet
Nazwa użytkownika: internet
Hasło: internet
Uwierzytelnianie: PAP
Typ APN: default,supl
Protokół APN: IPv4
Protokół APN podczas roamingu: IPv4Więc spróbowałem uruchomic komendy ręcznie:
root@WiesCityNetwork:~# socat - /dev/ttyACM0,crnl
AT+ZGACT=0,1
ERROR
AT+CFUN=1
OK
AT+ZGDCONT=1,"IP","internet","",0,0
+CME ERROR: Invalid ParamNie za bardzo rozumiem jak dalej debugować ten problem. Czy modem padł, czy coś Orange Flex pozmieniało, czy tez... Wlasnie, co jeszcze mogę sprawdzić?
Wyjmij kartę SIM, zobacz czy działa w telefonie, przeczyść styki.
@Cezary: Bardzo dziękuje za odpowiedź.
Faktycznie, coś nie tak ze stykami, chociaż wyjmowałem kartę SIM parę razy by różne opcje debugować - i nie pomagało.
Przetarłem styki z karty SIM, jak i też w modemie (kawałek papieru ściernego i wykałaczki).
Teraz działa jak należy 
Dziękuje za celną wskazówkę i wkład w pomoc ludziom, takich jak ja!
Poszukuję odpowiednika komendy do odczytania numeru karty SIM. Na innych połączeniach zwykle wystarcza
sms_tool -D -d /dev/ttyUSB1 at AT+ICCID
sms_tool -D -d /dev/ttyACM0 at AT+ICCIDa tu na NCM już nie. Jakąś komendą easyconfig jednak odczytuje ten numer.
AT*ICCID?easyconfig nie robi tego w jakiś tajemniczy sposób, po prostu czyta po kolei różne wariacje tego: https://github.com/obsy/packages/blob/m … oduct.gcom
Włącz sobie od razu monitor połączenia, bo pod openwrt ten modem nie zachowuje się stabilnie.
Posłusznie melduję, że po ostatniej (przed tą najnowszą z dzisiaj) aktualizacji jest już bardzo stabilne połączenie.
Zamiast wybrać "tylko LTE" zostawiam na "Wg ustawień modemu" - i tak trzyma LTE i w sumie kilka dni bez restartu.
Żadna różnica, dla tego konkretnego typu modemu i tak skrypty nie obsługują wyboru technologii połączenia.
Żadna różnica, dla tego konkretnego typu modemu i tak skrypty nie obsługują wyboru technologii połączenia.
Chyba jednak jest różnica. Sprawdzałem kilka razy. Przy wyborze 'wg ustawień modemu' IP od sieci otrzymywane jest w kilka sekund:
Tue Nov 26 23:13:09 2024 daemon.notice netifd: wan (326): sending -> AT+ZGACT=0,1 <= u mnie option delay '10'
Tue Nov 26 23:13:19 2024 daemon.notice netifd: wan (770): sending -> AT+CFUN=1
Tue Nov 26 23:13:19 2024 daemon.notice netifd: wan (770): Configuring modem
Tue Nov 26 23:13:19 2024 daemon.notice netifd: wan (770): sending -> AT+ZGDCONT=1,"IP","internet","",0,0
Tue Nov 26 23:13:21 2024 daemon.notice netifd: wan (770): sending -> AT+ZGPCOAUTH=1,"","",0
Tue Nov 26 23:13:21 2024 daemon.notice netifd: wan (770): Starting network wan
Tue Nov 26 23:13:21 2024 daemon.notice netifd: wan (770): Connecting modem
Tue Nov 26 23:13:22 2024 daemon.notice netifd: wan (770): sending -> AT+ZGACT=1,1
Tue Nov 26 23:13:22 2024 daemon.notice netifd: wan (770): Setting up usb0
Tue Nov 26 23:13:22 2024 daemon.notice netifd: Interface 'wan' is now up
Tue Nov 26 23:13:22 2024 daemon.info dnsmasq[1]: reading /tmp/resolv.conf.d/resolv.conf.auto
Tue Nov 26 23:13:22 2024 daemon.info dnsmasq[1]: using nameserver 8.8.8.8#53
Tue Nov 26 23:13:22 2024 daemon.info dnsmasq[1]: using nameserver 89.108.195.20#53
Tue Nov 26 23:13:22 2024 daemon.info dnsmasq[1]: using only locally-known addresses for test
Tue Nov 26 23:13:22 2024 daemon.info dnsmasq[1]: using only locally-known addresses for onion
Tue Nov 26 23:13:22 2024 daemon.info dnsmasq[1]: using only locally-known addresses for localhost
Tue Nov 26 23:13:22 2024 daemon.info dnsmasq[1]: using only locally-known addresses for local
Tue Nov 26 23:13:22 2024 daemon.info dnsmasq[1]: using only locally-known addresses for invalid
Tue Nov 26 23:13:22 2024 daemon.info dnsmasq[1]: using only locally-known addresses for bind
Tue Nov 26 23:13:22 2024 daemon.info dnsmasq[1]: using only locally-known addresses for lan
Tue Nov 26 23:13:22 2024 daemon.notice netifd: Network device 'usb0' link is up
Tue Nov 26 23:13:23 2024 daemon.notice netifd: Network alias 'usb0' link is up
Tue Nov 26 23:13:23 2024 daemon.notice netifd: Interface 'wan_4' is enabled
Tue Nov 26 23:13:23 2024 daemon.notice netifd: Interface 'wan_4' has link connectivity
Tue Nov 26 23:13:23 2024 daemon.notice netifd: Interface 'wan_4' is setting up now
Tue Nov 26 23:13:23 2024 daemon.notice netifd: wan_4 (1199): udhcpc: started, v1.36.1
Tue Nov 26 23:13:23 2024 daemon.notice netifd: wan_4 (1199): udhcpc: broadcasting discover
Tue Nov 26 23:13:24 2024 user.notice firewall: Reloading firewall due to ifup of wan (usb0)
Tue Nov 26 23:13:26 2024 daemon.notice netifd: wan_4 (1199): udhcpc: broadcasting discover
Tue Nov 26 23:13:26 2024 daemon.notice netifd: wan_4 (1199): udhcpc: broadcasting select for 10.146.184.65, server 10.146.184.190
Tue Nov 26 23:13:26 2024 daemon.notice netifd: wan_4 (1199): udhcpc: lease of 10.146.184.65 obtained from 10.146.184.190, lease time 7200
Tue Nov 26 23:13:27 2024 daemon.notice netifd: Interface 'wan_4' is now upzaś przy obecnym mode='auto' lub 'lte' (wybranym z GUI), na adres IP czeka się bardzo długo lub wcale, a w logu jakiś warning:
Tue Nov 26 23:12:10 2024 daemon.notice netifd: wan (30643): sending -> AT+ZGACT=0,1
Tue Nov 26 23:12:20 2024 daemon.notice netifd: wan (31083): sending -> AT+CFUN=1
Tue Nov 26 23:12:20 2024 daemon.notice netifd: wan (31083): Configuring modem
Tue Nov 26 23:12:20 2024 daemon.notice netifd: wan (31083): sending -> AT+ZGDCONT=1,"IP","internet","",0,0
Tue Nov 26 23:12:22 2024 daemon.notice netifd: wan (31083): sending -> AT+ZGPCOAUTH=1,"","",0
Tue Nov 26 23:12:22 2024 daemon.notice netifd: wan (31083): WARNING: Variable 'modes' does not exist or is not an array/object
Tue Nov 26 23:12:22 2024 daemon.notice netifd: wan (31083): Starting network wan
Tue Nov 26 23:12:22 2024 daemon.notice netifd: wan (31083): Setting up usb0
Tue Nov 26 23:12:22 2024 daemon.notice netifd: Interface 'wan' is now up
Tue Nov 26 23:12:22 2024 daemon.info dnsmasq[1]: reading /tmp/resolv.conf.d/resolv.conf.auto
Tue Nov 26 23:12:22 2024 daemon.info dnsmasq[1]: using nameserver 8.8.8.8#53
Tue Nov 26 23:12:22 2024 daemon.info dnsmasq[1]: using nameserver 89.108.195.20#53
Tue Nov 26 23:12:22 2024 daemon.info dnsmasq[1]: using only locally-known addresses for test
Tue Nov 26 23:12:22 2024 daemon.info dnsmasq[1]: using only locally-known addresses for onion
Tue Nov 26 23:12:22 2024 daemon.info dnsmasq[1]: using only locally-known addresses for localhost
Tue Nov 26 23:12:22 2024 daemon.info dnsmasq[1]: using only locally-known addresses for local
Tue Nov 26 23:12:22 2024 daemon.info dnsmasq[1]: using only locally-known addresses for invalid
Tue Nov 26 23:12:22 2024 daemon.info dnsmasq[1]: using only locally-known addresses for bind
Tue Nov 26 23:12:22 2024 daemon.info dnsmasq[1]: using only locally-known addresses for lan
Tue Nov 26 23:12:22 2024 daemon.notice netifd: Network device 'usb0' link is up
Tue Nov 26 23:12:23 2024 daemon.notice netifd: Network alias 'usb0' link is up
Tue Nov 26 23:12:23 2024 daemon.notice netifd: Interface 'wan_4' is enabled
Tue Nov 26 23:12:23 2024 daemon.notice netifd: Interface 'wan_4' has link connectivity
Tue Nov 26 23:12:23 2024 daemon.notice netifd: Interface 'wan_4' is setting up now
Tue Nov 26 23:12:23 2024 daemon.notice netifd: wan_4 (31482): udhcpc: started, v1.36.1
Tue Nov 26 23:12:23 2024 daemon.notice netifd: wan_4 (31482): udhcpc: broadcasting discover
Tue Nov 26 23:12:23 2024 user.notice firewall: Reloading firewall due to ifup of wan (usb0)
Tue Nov 26 23:12:26 2024 daemon.notice netifd: wan_4 (31482): udhcpc: broadcasting discover
Tue Nov 26 23:12:29 2024 daemon.notice netifd: wan_4 (31482): udhcpc: broadcasting discoverW configu jest rzecz jasna option mode 'auto'
Ad. Tak to kwestia tej linii - z mode psuje, zaś modes śmiga
Doskonale. Zawsze mówiłem żeby nie ufać w to co piszę i samemu sprawdzać, cieszę że to zrobiłeś.
1. Jak sam wykazałeś nie wysłał żadnego polecenia do zmiany technologii bo takiego czegoś nie ma, zaś:
Tue Nov 26 23:12:22 2024 daemon.notice netifd: wan (31083): WARNING: Variable 'modes' does not exist or is not an array/objectmodes jest ignorowane bo dla ncm go nie obsługuje, obsługuje tylko mode, gdyby tylko mode istniało...
2 ... a nie istnieje bo dla tego typu modemu nigdy nie wprowadziliśmy żadnego polecenia w tym celu. Raz że nie widzisz takich poleceń w logach, dwa: fizycznie w konfigu tego nie ma: https://github.com/openwrt/openwrt/blob … m.json#L94
A druga sprawa - to czy łączy się szybko czy nie kompletnie nie zależy od nas (zakładając że modem ma właściwe ustawienia) tylko od tego co modem z operatorem wyprawia.
Doskonale. Zawsze mówiłem żeby nie ufać w to co piszę i samemu sprawdzać, cieszę że to zrobiłeś.
1. Jak sam wykazałeś nie wysłał żadnego polecenia do zmiany technologii bo takiego czegoś nie ma, zaś:
Tue Nov 26 23:12:22 2024 daemon.notice netifd: wan (31083): WARNING: Variable 'modes' does not exist or is not an array/objectmodes jest ignorowane bo dla ncm go nie obsługuje, obsługuje tylko mode, gdyby tylko mode istniało...
2 ... a nie istnieje bo dla tego typu modemu nigdy nie wprowadziliśmy żadnego polecenia w tym celu. Raz że nie widzisz takich poleceń w logach, dwa: fizycznie w konfigu tego nie ma: https://github.com/openwrt/openwrt/blob … m.json#L94A druga sprawa - to czy łączy się szybko czy nie kompletnie nie zależy od nas (zakładając że modem ma właściwe ustawienia) tylko od tego co modem z operatorem wyprawia.
Rzeczywiście masz rację i ja troszkę też, w błąd wprowadza modem, bo ostrzega o 'modes' gdy zadane ma 'mode'.
Jednak na 3 próby przejścia na 'mode' i z powrotem na bez 'modes' ani 'mode', w tym pierwszym przypadku nie dostaję IP i to nie jest tylko opóźnienie - dlatego o tym zacząłem pisać.
# mode='auto' lub 'lte'
Wed Nov 27 10:33:14 2024 daemon.notice netifd: wan (14821): WARNING: Variable 'modes' does not exist or is not an array/object
Wed Nov 27 10:33:18 2024 daemon.notice netifd: wan_4 (15178): udhcpc: broadcasting discover
Wed Nov 27 10:33:21 2024 daemon.notice netifd: wan_4 (15178): udhcpc: broadcasting discover
Wed Nov 27 10:33:33 2024 user.info adblock-4.2.2-8[14602]: adblock is currently disabled, please set the config option 'adb_enabled' to '1' to use this service
Wed Nov 27 10:37:00 2024 cron.info crond[2321]: USER root pid 15935 cmd /usr/bin/easyconfig_statistics.sh
Wed Nov 27 10:38:00 2024 cron.info crond[2321]: USER root pid 16078 cmd /usr/bin/easyconfig_logs.sh
Wed Nov 27 10:38:00 2024 cron.info crond[2321]: USER root pid 16079 cmd /usr/bin/easyconfig_statistics.sh
# po 5 minutach nie ma IP
# bez linii 'mode' ani 'modes'
Wed Nov 27 10:39:16 2024 daemon.notice netifd: wan_4 (17255): udhcpc: started, v1.36.1
Wed Nov 27 10:39:16 2024 daemon.notice netifd: wan_4 (17255): udhcpc: broadcasting discover
Wed Nov 27 10:39:16 2024 user.notice firewall: Reloading firewall due to ifup of wan (usb0)
Wed Nov 27 10:39:19 2024 daemon.notice netifd: wan_4 (17255): udhcpc: broadcasting discover
Wed Nov 27 10:39:19 2024 daemon.notice netifd: wan_4 (17255): udhcpc: broadcasting select for 10.137.48.90, server 10.137.48.165
Wed Nov 27 10:39:19 2024 daemon.notice netifd: wan_4 (17255): udhcpc: lease of 10.137.48.90 obtained from 10.137.48.165, lease time 7200W każdym razie w GUI nie wybiorę dzisiaj opcji innej niż 'wg modemu' już nigdy.
A co jeśli inni z MF286R też tak mają ?
Na moim wersja FW: BD_MF286MODV1.0.0B03
Wg to efekt placebo, nic nie wysyła więc opcja jest całkowicie ignorowana i tak, bo nic się pod nią nie kryje dla tego modemu. Inna sprawa że modem w MF286R jest ciężko strawny co już pisałem i czasami na problemy z połączeniem.
Wg to efekt placebo, nic nie wysyła więc opcja jest całkowicie ignorowana i tak, bo nic się pod nią nie kryje dla tego modemu. Inna sprawa że modem w MF286R jest ciężko strawny co już pisałem i czasami na problemy z połączeniem.
Z obserwacji wynika, że przy bdb zasięgu (i agregacji full auto) powoli jego ciemne moce słabną potem leci na minimum np. 2Mbit/s (przy uploadzie 10x większym) - wtedy bez restartu nie chce się obudzić. Może zapychają się jemu jakieś stosy/tablice albo sie sam pakuje na czarne listy bts'u. Czy istnieje inny firmware do wgrania ?
Ostatnia terapia poprzez "AT+CFUN=1,1" zawiesiła cały ruter, potem reset do fabrycznych i wgranie ostatniego konfigu - i wtedy zaczął normalnie gadać.
Cześć wszystkim 
Przeszukałem Google ale nie mogę znaleźć odpowiedzi na problem który mam po zakupie MF-286R.
Kupiłem to urządzenie w czarnej wersji Plus / Cyfrowy Polsat z myślą że jest kompatybilne z OpenWRT
Wgrałem OpenWRT i jakoś nie wykrywało /dev/ttyACM0 przy konfiguracji ncm w LuCi
Huh... przywróciłem fabryczny soft by upewnić się że jest zaktualizowany i tu pojawia się problem
Mam kartę z Orange i jej nie wykrywa - "Brak karty SIM lub karta SIM jest nieprawidłowa!"
na górze panelu "usługi ograniczone", po najechaniu na symbol SIM "Nieprawidłowa karta SIM"
Ta sama karta działa bez problemu w ZTE MF258K z Play, oraz w Huawei B535-232
Myślałem że bubel z lombardu ma uszkodzony slot na kartę - doginałem piny, dociskałem, nic nie pomogło.
Przełożyłem kartę Vectra z telefonu i działa...
Kupiłem starter z nju mobile (nawet jeszcze nie rejestrowałem karty), wkładam i to samo jak z Orange - "Brak karty SIM lub karta SIM jest nieprawidłowa!"
Czyżby te urządzenia miały SIM-Lock ale nie pokazywały żadnego komunikatu? W Google nic nie znalazłem na ten temat
Pozdrawiam
Vectra to Play.
Sprawdź czy to urządzenie nie jest na liście zablokowanych: https://www.plus.pl/formularze/formularz-imei
Sprawdziłem, wygląda na to że urządzenie jest już spłacone
Informujemy, że właścicielem urządzenia nie jest Polkomtel Sp. z o.o.
Jeżeli tak jest faktycznie to nie ma podstaw żeby nie działało
Wgrywaj openwrt jeszcze raz i pokaż
cat /sys/kernel/debug/usb/devices
zobaczymy co to ten sam modem co w innych 286R.
root@OpenWrt:~# cat /sys/kernel/debug/usb/devices
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 1
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0002 Rev= 6.06
S: Manufacturer=Linux 6.6.60 ehci_hcd
S: Product=EHCI Host Controller
S: SerialNumber=1b000000.usb
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=19d2 ProdID=1489 Rev=ff.ff
S: Manufacturer=ZTE
S: Product=ZTE
S: SerialNumber=123456789ABCD
C:* #Ifs= 6 Cfg#= 1 Atr=e0 MxPwr= 2mA
A: FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=03
A: FirstIf#= 2 IfCount= 2 Cls=02(comm.) Sub=02 Prot=01
I:* If#= 0 Alt= 0 #EPs= 1 Cls=e0(wlcon) Sub=01 Prot=03 Driver=rndis_host
E: Ad=82(I) Atr=03(Int.) MxPS= 8 Ivl=1ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=rndis_host
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=02 Prot=01 Driver=cdc_acm
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_acm
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=ff Driver=(none)
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 1
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0002 Rev= 6.06
S: Manufacturer=Linux 6.6.60 ehci_hcd
S: Product=EHCI Host Controller
S: SerialNumber=1b400000.usb
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256msNormalnie masz. Musisz mieć /dev/ttyACM* (chyba że się później rozłączy na usb).
Przy konfiguracji w LuCi dodaję interfejs, protokół NCM, a w polu Modem nie ma listy do wyboru
wpisując ręcznie /dev/ttyACM0 wychodzi to:
Protokół: NCM
RX: 0 B (0 Pktw.)
TX: 0 B (0 Pktw.)
Błąd: Urządzenie sieciowe nie jest obecneAle gdy zmieniam Protokół na UMTS/GPRS/EV-DO jest lista w polu Modem i tam /dev/ttyACM0 jest dostępny do wyboru...
Nie rozumiem tego dlaczego nie wykrywa tych kart Orange/Nju
Teraz na OpenWRT wrzuciłem kartę Vectra i wciąż ten interfejs NCM wyświetla "Urządzenie sieciowe nie jest obecne"
A tak się cieszyłem że tanio kupiłem i będzie LTE z OpenWRT bo potrzebuję do DNS Controld...
Hah, taka oszczędność że wiele godzin zmarnowane i chyba pozostaje zostawienie B535 jako gateway, tylko on zaś nie ma trybu bridge 
Pokaż wynik
uci show network
Proszę wynik
root@OpenWrt:~# uci show network
network.loopback=interface
network.loopback.device='lo'
network.loopback.proto='static'
network.loopback.ipaddr='127.0.0.1'
network.loopback.netmask='255.0.0.0'
network.globals=globals
network.globals.ula_prefix='fd8c:6d1a:cb89::/48'
network.@device[0]=device
network.@device[0].name='br-lan'
network.@device[0].type='bridge'
network.@device[0].ports='eth0.1'
network.lan=interface
network.lan.device='br-lan'
network.lan.proto='static'
network.lan.ipaddr='192.168.1.1'
network.lan.netmask='255.255.255.0'
network.lan.ip6assign='60'
network.@switch[0]=switch
network.@switch[0].name='switch0'
network.@switch[0].reset='1'
network.@switch[0].enable_vlan='1'
network.@switch_vlan[0]=switch_vlan
network.@switch_vlan[0].device='switch0'
network.@switch_vlan[0].vlan='1'
network.@switch_vlan[0].ports='1 2 3 5 0t'
network.wwan=interface
network.wwan.proto='ncm'
network.wwan.device='/dev/ttyACM0'
network.wwan.pdptype='IP'
network.wwan.apn='internet'To jest w sumie tylko to co domyśle jest w twoim obrazie OpenWRT + interfejs z wiki
https://openwrt.org/toh/zte/mf286r#basic_configuration
który jak rozumiem jest dokładnie tym samym co wyklikać w LuCi w interfejsach
edit: kurczę ja nie rozumiem tego dlaczego czyta Vectra (Play) a nie czyta w ogóle Orange (który w dwóch innych urządzeniach i telefonie działa bez problemu) i nowego Nju
Może faktycznie czymś się ta wersja czarna od Plusa/Polsatu rózni w oprogramowaniu modemu chociażby?
edit2: ale w sumie Vectra wsadziłem pod OpenWRT i nic to nie zmieniło w kwestii "Błąd: Urządzenie sieciowe nie jest obecne"
Tak, mniej więcej tak to wyglądało, pdptype możesz nawet usunąć.
Zrób ifup wwan poczekaj z 10s i pokaż wynik logread.
root@OpenWrt:~# ifup wwan
root@OpenWrt:~# logread
Sat Nov 16 00:32:55 2024 kern.notice kernel: [ 0.000000] Linux version 6.6.60 (cezary@eko.one.pl) (mips-openwrt-linux-musl-gcc (OpenWrt GCC 13.3.0 r28010-49d8f4b833) 13.3.0, GNU ld (GNU Binutils) 2.42) #0 Fri Nov 15 23:11:29 2024
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 0.000000] printk: bootconsole [early0] enabled
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 0.000000] CPU0 revision is: 00019750 (MIPS 74Kc)
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 0.000000] MIPS: machine is ZTE MF286R
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 0.000000] SoC: Qualcomm Atheros QCA956X ver 1 rev 0
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 0.000000] Initrd not found or empty - disabling initrd
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 0.000000] Zone ranges:
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 0.000000] Movable zone start for each node
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 0.000000] Early memory node ranges
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
Sat Nov 16 00:32:55 2024 kern.debug kernel: [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
Sat Nov 16 00:32:55 2024 kern.debug kernel: [ 0.000000] pcpu-alloc: [0] 0
Sat Nov 16 00:32:55 2024 kern.notice kernel: [ 0.000000] Kernel command line: console=ttyS0,115200n8 rootfstype=squashfs,jffs2
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 0.000000] Writing ErrCtl register=00000000
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 0.000000] Readback ErrCtl register=00000000
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32480
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 0.000000] Memory: 119000K/131072K available (7681K kernel code, 592K rwdata, 968K rodata, 1244K init, 240K bss, 12072K reserved, 0K cma-reserved)
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 0.000000] NR_IRQS: 51
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 0.000000] CPU clock: 775.000 MHz
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4932285024 ns
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 0.000001] sched_clock: 32 bits at 388MHz, resolution 2ns, wraps every 5541893118ns
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 0.008304] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 0.074797] pid_max: default: 32768 minimum: 301
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 0.089146] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 0.096883] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 0.113473] RCU Tasks Trace: Setting shift to 0 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=1.
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 0.128019] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 0.138438] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 0.148120] pinctrl core: initialized pinctrl subsystem
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 0.156758] NET: Registered PF_NETLINK/PF_ROUTE protocol family
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 0.163541] thermal_sys: Registered thermal governor 'step_wise'
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 0.177870] clocksource: Switched to clocksource MIPS
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 0.199820] NET: Registered PF_INET protocol family
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 0.205218] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 0.214271] tcp_listen_portaddr_hash hash table entries: 1024 (order: 0, 4096 bytes, linear)
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 0.223249] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 0.231430] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 0.239520] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear)
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 0.246981] TCP: Hash tables configured (established 1024 bind 1024)
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 0.254385] MPTCP token hash table entries: 512 (order: 0, 6144 bytes, linear)
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 0.262289] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 0.269224] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 0.277464] NET: Registered PF_UNIX/PF_LOCAL protocol family
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 0.283530] PCI: CLS 0 bytes, default 32
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 0.292299] workingset: timestamp_bits=14 max_order=15 bucket_order=1
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 0.300737] squashfs: version 4.0 (2009/01/31) Phillip Lougher
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 0.306892] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 0.324587] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 0.335750] pinctrl-single 1804002c.pinmux: 544 pins, size 68
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 0.343258] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 0.355188] printk: console [ttyS0] disabled
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 0.360235] 18020000.uart: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 1562500) is a 16550A
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 0.369501] printk: console [ttyS0] enabled
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 0.378570] printk: bootconsole [early0] disabled
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 0.424376] spi-nor spi0.0: gd25q16 (2048 Kbytes)
Sat Nov 16 00:32:55 2024 kern.notice kernel: [ 0.429390] 3 fixed-partitions partitions found on MTD device spi0.0
Sat Nov 16 00:32:55 2024 kern.notice kernel: [ 0.435960] Creating 3 MTD partitions on "spi0.0":
Sat Nov 16 00:32:55 2024 kern.notice kernel: [ 0.440930] 0x000000000000-0x0000000a0000 : "u-boot"
Sat Nov 16 00:32:55 2024 kern.notice kernel: [ 0.448842] 0x0000000a0000-0x0000000c0000 : "u-boot-env"
Sat Nov 16 00:32:55 2024 kern.notice kernel: [ 0.456283] 0x0000000c0000-0x000000200000 : "reserved1"
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 0.465597] spi-nand spi0.1: GigaDevice SPI NAND was found.
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 0.471427] spi-nand spi0.1: 128 MiB, block size: 128 KiB, page size: 2048, OOB size: 128
Sat Nov 16 00:32:55 2024 kern.notice kernel: [ 0.480022] 6 fixed-partitions partitions found on MTD device (null)
Sat Nov 16 00:32:55 2024 kern.notice kernel: [ 0.486602] Creating 6 MTD partitions on "(null)":
Sat Nov 16 00:32:55 2024 kern.notice kernel: [ 0.491583] 0x000000000000-0x0000000a0000 : "fota-flag"
Sat Nov 16 00:32:55 2024 kern.notice kernel: [ 0.502807] 0x0000000a0000-0x000000120000 : "art"
Sat Nov 16 00:32:55 2024 kern.err kernel: [ 0.510484] OF: Bad cell count for /ahb/spi@1f000000/flash@1/partitions
Sat Nov 16 00:32:55 2024 kern.notice kernel: [ 0.517593] 0x000000120000-0x0000001a0000 : "mac"
Sat Nov 16 00:32:55 2024 kern.err kernel: [ 0.525717] OF: Bad cell count for /ahb/spi@1f000000/flash@1/partitions
Sat Nov 16 00:32:55 2024 kern.notice kernel: [ 0.532878] 0x0000001a0000-0x000001800000 : "ubiconcat0"
Sat Nov 16 00:32:55 2024 kern.notice kernel: [ 0.568606] 0x000001800000-0x000001c00000 : "kernel"
Sat Nov 16 00:32:55 2024 kern.notice kernel: [ 0.580768] 0x000001c00000-0x000008000000 : "ubiconcat1"
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 1.412291] switch0: Atheros AR8337 rev. 2 switch registered on mdio.0
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 2.069605] ag71xx-legacy 19000000.eth: connected to PHY at mdio.0:00 [uid=004dd036, driver=Atheros AR8216/AR8236/AR8316]
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 2.081724] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode: sgmii
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 2.091892] NET: Registered PF_INET6 protocol family
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 2.109664] Segment Routing with IPv6
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 2.113535] In-situ OAM (IOAM) with IPv6
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 2.117731] NET: Registered PF_PACKET protocol family
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 2.123056] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 2.136721] 8021q: 802.1Q VLAN Support v1.8
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 2.181319] PCI host bridge to bus 0000:00
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 2.185575] pci_bus 0000:00: root bus resource [mem 0x12000000-0x13ffffff]
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 2.192735] pci_bus 0000:00: root bus resource [io 0x0000]
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 2.198509] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 2.206735] pci 0000:00:00.0: [168c:0056] type 00 class 0x028000
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 2.212987] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 2.220143] pci 0000:00:00.0: PME# supported from D0 D3hot
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 2.226888] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 2.233792] pci 0000:00:00.0: BAR 0: assigned [mem 0x12000000-0x121fffff 64bit]
Sat Nov 16 00:32:55 2024 kern.notice kernel: [ 2.241740] Concatenating MTD devices:
Sat Nov 16 00:32:55 2024 kern.notice kernel: [ 2.245626] (0): "ubiconcat0"
Sat Nov 16 00:32:55 2024 kern.notice kernel: [ 2.248729] (1): "ubiconcat1"
Sat Nov 16 00:32:55 2024 kern.notice kernel: [ 2.251797] into device "ubi-concat"
Sat Nov 16 00:32:55 2024 kern.notice kernel: [ 2.255521] 1 fixed-partitions partitions found on MTD device ubi-concat
Sat Nov 16 00:32:55 2024 kern.notice kernel: [ 2.262458] Creating 1 MTD partitions on "ubi-concat":
Sat Nov 16 00:32:55 2024 kern.notice kernel: [ 2.267770] 0x000000000000-0x000007a60000 : "ubi"
Sat Nov 16 00:32:55 2024 kern.notice kernel: [ 2.279806] UBI: auto-attach mtd9
Sat Nov 16 00:32:55 2024 kern.notice kernel: [ 2.283270] ubi0: attaching mtd9
Sat Nov 16 00:32:55 2024 kern.notice kernel: [ 4.948822] ubi0: scanning is finished
Sat Nov 16 00:32:55 2024 kern.notice kernel: [ 4.987030] ubi0: attached mtd9 (name "ubi", size 122 MiB)
Sat Nov 16 00:32:55 2024 kern.notice kernel: [ 4.992768] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
Sat Nov 16 00:32:55 2024 kern.notice kernel: [ 4.999883] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
Sat Nov 16 00:32:55 2024 kern.notice kernel: [ 5.006898] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
Sat Nov 16 00:32:55 2024 kern.notice kernel: [ 5.014092] ubi0: good PEBs: 974, bad PEBs: 5, corrupted PEBs: 0
Sat Nov 16 00:32:55 2024 kern.notice kernel: [ 5.020301] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
Sat Nov 16 00:32:55 2024 kern.notice kernel: [ 5.027758] ubi0: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 716350522
Sat Nov 16 00:32:55 2024 kern.notice kernel: [ 5.037113] ubi0: available PEBs: 0, total reserved PEBs: 974, PEBs reserved for bad PEB handling: 15
Sat Nov 16 00:32:55 2024 kern.notice kernel: [ 5.046729] ubi0: background thread "ubi_bgt0d" started, PID 314
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 5.055401] block ubiblock0_0: created from ubi0:0(rootfs)
Sat Nov 16 00:32:55 2024 kern.notice kernel: [ 5.061138] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 5.068535] clk: Disabling unused clocks
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 5.092900] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 5.106931] Freeing unused kernel image (initmem) memory: 1244K
Sat Nov 16 00:32:55 2024 kern.warn kernel: [ 5.113087] This architecture does not have kernel memory protection.
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 5.119751] Run /sbin/init as init process
Sat Nov 16 00:32:55 2024 kern.debug kernel: [ 5.123979] with arguments:
Sat Nov 16 00:32:55 2024 kern.debug kernel: [ 5.123984] /sbin/init
Sat Nov 16 00:32:55 2024 kern.debug kernel: [ 5.123990] with environment:
Sat Nov 16 00:32:55 2024 kern.debug kernel: [ 5.123994] HOME=/
Sat Nov 16 00:32:55 2024 kern.debug kernel: [ 5.123999] TERM=linux
Sat Nov 16 00:32:55 2024 user.info kernel: [ 5.924417] init: Console is alive
Sat Nov 16 00:32:55 2024 user.info kernel: [ 5.928424] init: - watchdog -
Sat Nov 16 00:32:55 2024 user.info kernel: [ 8.969239] kmodloader: loading kernel modules from /etc/modules-boot.d/*
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 9.037208] usbcore: registered new interface driver usbfs
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 9.043020] usbcore: registered new interface driver hub
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 9.048625] usbcore: registered new device driver usb
Sat Nov 16 00:32:55 2024 kern.warn kernel: [ 9.131460] gpio_button_hotplug: loading out-of-tree module taints kernel.
Sat Nov 16 00:32:55 2024 kern.notice kernel: [ 9.156254] SCSI subsystem initialized
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 9.170502] ehci-platform 1b000000.usb: EHCI Host Controller
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 9.176410] ehci-platform 1b000000.usb: new USB bus registered, assigned bus number 1
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 9.184672] ehci-platform 1b000000.usb: irq 15, io mem 0x1b000000
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 9.191407] ehci-platform 1b400000.usb: EHCI Host Controller
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 9.197289] ehci-platform 1b400000.usb: new USB bus registered, assigned bus number 2
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 9.205571] ehci-platform 1b400000.usb: irq 16, io mem 0x1b400000
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 9.217930] ehci-platform 1b000000.usb: USB 2.0 started, EHCI 1.00
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 9.225235] hub 1-0:1.0: USB hub found
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 9.229958] hub 1-0:1.0: 1 port detected
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 9.257895] ehci-platform 1b400000.usb: USB 2.0 started, EHCI 1.00
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 9.265262] hub 2-0:1.0: USB hub found
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 9.270079] hub 2-0:1.0: 1 port detected
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 9.283777] usbcore: registered new interface driver usb-storage
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 9.293023] usbcore: registered new interface driver uas
Sat Nov 16 00:32:55 2024 user.info kernel: [ 9.299924] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
Sat Nov 16 00:32:55 2024 user.info kernel: [ 9.317982] init: - preinit -
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 9.518825] usb 1-1: new high-speed USB device number 2 using ehci-platform
Sat Nov 16 00:32:55 2024 kern.notice kernel: [ 10.407922] random: crng init done
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 13.380770] Atheros AR8216/AR8236/AR8316 mdio.0:00: Port 1 is up
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 13.397952] eth0: link up (1000Mbps/Full duplex)
Sat Nov 16 00:32:55 2024 user.info kernel: [ 17.718876] mount_root: loading kmods from internal overlay
Sat Nov 16 00:32:55 2024 user.info kernel: [ 17.774787] kmodloader: loading kernel modules from //etc/modules-boot.d/*
Sat Nov 16 00:32:55 2024 user.info kernel: [ 17.795585] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
Sat Nov 16 00:32:55 2024 user.info kernel: [ 18.489587] block: attempting to load /tmp/overlay/upper/etc/config/fstab
Sat Nov 16 00:32:55 2024 user.err kernel: [ 18.496938] block: unable to load configuration (fstab: Entry not found)
Sat Nov 16 00:32:55 2024 user.info kernel: [ 18.504246] block: attempting to load /tmp/overlay/etc/config/fstab
Sat Nov 16 00:32:55 2024 user.err kernel: [ 18.511137] block: unable to load configuration (fstab: Entry not found)
Sat Nov 16 00:32:55 2024 user.info kernel: [ 18.519232] block: attempting to load /etc/config/fstab
Sat Nov 16 00:32:55 2024 user.err kernel: [ 18.530602] block: unable to load configuration (fstab: Entry not found)
Sat Nov 16 00:32:55 2024 user.err kernel: [ 18.537799] block: no usable configuration
Sat Nov 16 00:32:55 2024 kern.notice kernel: [ 18.550884] UBIFS (ubi0:1): Mounting in unauthenticated mode
Sat Nov 16 00:32:55 2024 kern.notice kernel: [ 18.557012] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 537
Sat Nov 16 00:32:55 2024 kern.notice kernel: [ 18.738290] UBIFS (ubi0:1): recovery needed
Sat Nov 16 00:32:55 2024 kern.notice kernel: [ 19.126446] UBIFS (ubi0:1): recovery completed
Sat Nov 16 00:32:55 2024 kern.notice kernel: [ 19.131171] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
Sat Nov 16 00:32:55 2024 kern.notice kernel: [ 19.139281] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
Sat Nov 16 00:32:55 2024 kern.notice kernel: [ 19.149532] UBIFS (ubi0:1): FS size: 111865856 bytes (106 MiB, 881 LEBs), max 892 LEBs, journal size 5586944 bytes (5 MiB, 44 LEBs)
Sat Nov 16 00:32:55 2024 kern.notice kernel: [ 19.161752] UBIFS (ubi0:1): reserved for root: 4952683 bytes (4836 KiB)
Sat Nov 16 00:32:55 2024 kern.notice kernel: [ 19.168589] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID 1BB08F8F-D07D-43D9-9202-4B3B98063F68, small LPT model
Sat Nov 16 00:32:55 2024 user.info kernel: [ 19.190829] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
Sat Nov 16 00:32:55 2024 user.info kernel: [ 19.226794] block: extroot: not configured
Sat Nov 16 00:32:55 2024 kern.notice kernel: [ 19.231358] UBIFS (ubi0:1): un-mount UBI device 0
Sat Nov 16 00:32:55 2024 kern.notice kernel: [ 19.236291] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" stops
Sat Nov 16 00:32:55 2024 kern.notice kernel: [ 19.253021] UBIFS (ubi0:1): Mounting in unauthenticated mode
Sat Nov 16 00:32:55 2024 kern.notice kernel: [ 19.259149] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 540
Sat Nov 16 00:32:55 2024 kern.notice kernel: [ 19.632151] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
Sat Nov 16 00:32:55 2024 kern.notice kernel: [ 19.640304] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
Sat Nov 16 00:32:55 2024 kern.notice kernel: [ 19.650557] UBIFS (ubi0:1): FS size: 111865856 bytes (106 MiB, 881 LEBs), max 892 LEBs, journal size 5586944 bytes (5 MiB, 44 LEBs)
Sat Nov 16 00:32:55 2024 kern.notice kernel: [ 19.662778] UBIFS (ubi0:1): reserved for root: 4952683 bytes (4836 KiB)
Sat Nov 16 00:32:55 2024 kern.notice kernel: [ 19.669614] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID 1BB08F8F-D07D-43D9-9202-4B3B98063F68, small LPT model
Sat Nov 16 00:32:55 2024 user.info kernel: [ 20.094457] block: attempting to load /tmp/overlay/upper/etc/config/fstab
Sat Nov 16 00:32:55 2024 user.info kernel: [ 20.126149] block: extroot: not configured
Sat Nov 16 00:32:55 2024 user.info kernel: [ 20.134700] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
Sat Nov 16 00:32:55 2024 user.info kernel: [ 20.142833] block: extroot: not configured
Sat Nov 16 00:32:55 2024 user.info kernel: [ 20.153839] mount_root: switching to ubifs overlay
Sat Nov 16 00:32:55 2024 user.warn kernel: [ 20.209322] urandom-seed: Seeding with /etc/urandom.seed
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 20.315060] eth0: link down
Sat Nov 16 00:32:55 2024 user.info kernel: [ 20.340386] procd: - early -
Sat Nov 16 00:32:55 2024 user.info kernel: [ 20.343675] procd: - watchdog -
Sat Nov 16 00:32:55 2024 user.info kernel: [ 21.238080] procd: - watchdog -
Sat Nov 16 00:32:55 2024 user.info kernel: [ 21.270437] procd: - ubus -
Sat Nov 16 00:32:55 2024 user.info kernel: [ 21.491604] procd: - init -
Sat Nov 16 00:32:55 2024 user.info kernel: [ 25.027916] kmodloader: loading kernel modules from /etc/modules.d/*
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 26.573791] OpenVPN data channel offload (ovpn-dco) 2.0.0 -- (C) 2020-2023 OpenVPN, Inc.
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 26.621758] tun: Universal TUN/TAP device driver, 1.6
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 26.788140] ntfs3: Enabled Linux POSIX ACLs support
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 26.924053] cdc_acm 1-1:1.2: ttyACM0: USB ACM device
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 26.929440] usbcore: registered new interface driver cdc_acm
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 26.935290] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
Sat Nov 16 00:32:55 2024 user.info kernel: [ 26.947745] urngd: v1.0.2 started.
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 26.989659] usbcore: registered new interface driver cdc_wdm
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 27.028809] Loading modules backported from Linux version v6.11.2-0-g7aa21fec187b
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 27.036558] Backport generated by backports.git v6.1.110-1-32-gc61f71fe0942
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 27.180448] usbcore: registered new interface driver usblp
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 27.242070] usbcore: registered new interface driver usbserial_generic
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 27.248961] usbserial: USB Serial support registered for generic
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 27.309965] usbcore: registered new interface driver cdc_ether
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 27.345173] usbcore: registered new interface driver cdc_ncm
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 27.499401] usbcore: registered new interface driver huawei_cdc_ncm
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 28.351765] PPP generic driver version 2.4.2
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 28.389216] NET: Registered PF_PPPOX protocol family
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 28.430836] usbcore: registered new interface driver qmi_wwan
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 28.518857] rndis_host 1-1:1.0 eth1: register 'rndis_host' at usb-1b000000.usb-1, ZTE RNDIS device, ee:de:4c:f3:8f:bc
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 28.530104] usbcore: registered new interface driver rndis_host
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 28.560162] usbcore: registered new interface driver sierra
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 28.566053] usbserial: USB Serial support registered for Sierra USB modem
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 28.632711] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information.
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 28.640863] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 28.851175] ath10k 6.10 driver, optimized for CT firmware, probing pci device: 0x56.
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 28.958850] ath10k_pci 0000:00:00.0: enabling device (0000 -> 0002)
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 28.965646] ath10k_pci 0000:00:00.0: pci irq legacy oper_irq_mode 1 irq_mode 0 reset_mode 0
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 37.949936] ath10k_pci 0000:00:00.0: qca9888 hw2.0 target 0x01000000 chip_id 0x00000000 sub 0000:0000
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 37.959516] ath10k_pci 0000:00:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 37.973983] ath10k_pci 0000:00:00.0: firmware ver 10.4b-ct-9888-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 59e741e7
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 38.330786] ath10k_pci 0000:00:00.0: board_file api 2 bmi_id 0:16 crc32 5968d47d
Sat Nov 16 00:32:55 2024 kern.warn kernel: [ 40.104620] ath10k_pci 0000:00:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
Sat Nov 16 00:32:55 2024 kern.warn kernel: [ 40.112431] ath10k_pci 0000:00:00.0: msdu-desc: 2500 skid: 32
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 40.162472] ath10k_pci 0000:00:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 40.173783] ath10k_pci 0000:00:00.0: wmi print 'free: 114572 iram: 12644 sram: 29508'
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 40.409863] ath10k_pci 0000:00:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-nvmem max-sta 32 raw 0 hwcrypto 1
Sat Nov 16 00:32:55 2024 kern.debug kernel: [ 40.511374] ath: EEPROM regdomain: 0x0
Sat Nov 16 00:32:55 2024 kern.debug kernel: [ 40.511400] ath: EEPROM indicates default country code should be used
Sat Nov 16 00:32:55 2024 kern.debug kernel: [ 40.511406] ath: doing EEPROM country->regdmn map search
Sat Nov 16 00:32:55 2024 kern.debug kernel: [ 40.511421] ath: country maps to regdmn code: 0x3a
Sat Nov 16 00:32:55 2024 kern.debug kernel: [ 40.511428] ath: Country alpha2 being used: US
Sat Nov 16 00:32:55 2024 kern.debug kernel: [ 40.511436] ath: Regpair used: 0x3a
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 40.600559] usbcore: registered new interface driver cdc_mbim
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 40.621472] usbcore: registered new interface driver option
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 40.627318] usbserial: USB Serial support registered for GSM modem (1-port)
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 40.653003] usbcore: registered new interface driver qcserial
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 40.659083] usbserial: USB Serial support registered for Qualcomm USB modem
Sat Nov 16 00:32:55 2024 kern.debug kernel: [ 40.728072] ath: EEPROM regdomain: 0x0
Sat Nov 16 00:32:55 2024 kern.debug kernel: [ 40.728099] ath: EEPROM indicates default country code should be used
Sat Nov 16 00:32:55 2024 kern.debug kernel: [ 40.728105] ath: doing EEPROM country->regdmn map search
Sat Nov 16 00:32:55 2024 kern.debug kernel: [ 40.728121] ath: country maps to regdmn code: 0x3a
Sat Nov 16 00:32:55 2024 kern.debug kernel: [ 40.728128] ath: Country alpha2 being used: US
Sat Nov 16 00:32:55 2024 kern.debug kernel: [ 40.728135] ath: Regpair used: 0x3a
Sat Nov 16 00:32:55 2024 kern.debug kernel: [ 40.739933] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
Sat Nov 16 00:32:55 2024 kern.info kernel: [ 40.740890] ieee80211 phy1: Atheros AR9561 Rev:0 mem=0x2b9635d3, irq=2
Sat Nov 16 00:32:55 2024 user.info kernel: [ 40.778423] kmodloader: done loading kernel modules from /etc/modules.d/*
Sat Nov 16 00:32:58 2024 user.notice dnsmasq: DNS rebinding protection is active, will discard upstream RFC1918 responses!
Sat Nov 16 00:32:58 2024 user.notice dnsmasq: Allowing 127.0.0.0/8 responses
Sat Nov 16 00:32:58 2024 user.notice dnsmasq: Allowing RFC1918 responses for domain free.aero2.net.pl
Sat Nov 16 00:32:59 2024 daemon.info dnsmasq[1]: started, version 2.90 cachesize 1000
Sat Nov 16 00:32:59 2024 daemon.info dnsmasq[1]: DNS service limited to local subnets
Sat Nov 16 00:32:59 2024 daemon.info dnsmasq[1]: compile time options: IPv6 GNU-getopt no-DBus UBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-nftset no-auth no-cryptohash no-DNSSEC no-ID loop-detect inotify dumpfile
Sat Nov 16 00:32:59 2024 daemon.info dnsmasq[1]: UBus support enabled: connected to system bus
Sat Nov 16 00:32:59 2024 daemon.info dnsmasq[1]: using only locally-known addresses for test
Sat Nov 16 00:32:59 2024 daemon.info dnsmasq[1]: using only locally-known addresses for onion
Sat Nov 16 00:32:59 2024 daemon.info dnsmasq[1]: using only locally-known addresses for localhost
Sat Nov 16 00:32:59 2024 daemon.info dnsmasq[1]: using only locally-known addresses for local
Sat Nov 16 00:32:59 2024 daemon.info dnsmasq[1]: using only locally-known addresses for invalid
Sat Nov 16 00:32:59 2024 daemon.info dnsmasq[1]: using only locally-known addresses for bind
Sat Nov 16 00:32:59 2024 daemon.info dnsmasq[1]: using only locally-known addresses for lan
Sat Nov 16 00:32:59 2024 daemon.warn dnsmasq[1]: no servers found in /tmp/resolv.conf.d/resolv.conf.auto, will retry
Sat Nov 16 00:32:59 2024 daemon.info dnsmasq[1]: read /etc/hosts - 12 names
Sat Nov 16 00:32:59 2024 daemon.info dnsmasq[1]: read /tmp/hosts/dhcp.cfg01411c - 0 names
Sat Nov 16 00:33:00 2024 authpriv.info dropbear[2020]: Not backgrounding
Sat Nov 16 00:33:05 2024 daemon.notice wpa_supplicant[2133]: Successfully initialized wpa_supplicant
Sat Nov 16 00:33:05 2024 user.notice : Added device handler type: bonding
Sat Nov 16 00:33:05 2024 user.notice : Added device handler type: 8021ad
Sat Nov 16 00:33:05 2024 user.notice : Added device handler type: 8021q
Sat Nov 16 00:33:05 2024 user.notice : Added device handler type: macvlan
Sat Nov 16 00:33:05 2024 user.notice : Added device handler type: veth
Sat Nov 16 00:33:05 2024 user.notice : Added device handler type: bridge
Sat Nov 16 00:33:05 2024 user.notice : Added device handler type: Network device
Sat Nov 16 00:33:05 2024 user.notice : Added device handler type: tunnel
Sat Nov 16 00:33:10 2024 user.info adblock-4.2.2-r8[2436]: dns backend directory '/tmp/dnsmasq.d' created
Sat Nov 16 00:33:10 2024 user.info adblock-4.2.2-r8[2436]: backup directory '/tmp/adblock-Backup' created
Sat Nov 16 00:33:11 2024 daemon.info dnsmasq[1]: exiting on receipt of SIGTERM
Sat Nov 16 00:33:15 2024 kern.info kernel: [ 64.963939] eth0: link up (1000Mbps/Full duplex)
Sat Nov 16 00:33:15 2024 kern.info kernel: [ 64.976486] br-lan: port 1(eth0.1) entered blocking state
Sat Nov 16 00:33:15 2024 kern.info kernel: [ 64.982150] br-lan: port 1(eth0.1) entered disabled state
Sat Nov 16 00:33:15 2024 kern.info kernel: [ 64.987765] eth0.1: entered allmulticast mode
Sat Nov 16 00:33:15 2024 kern.info kernel: [ 64.992302] ag71xx-legacy 19000000.eth eth0: entered allmulticast mode
Sat Nov 16 00:33:15 2024 kern.info kernel: [ 64.999320] eth0.1: entered promiscuous mode
Sat Nov 16 00:33:15 2024 kern.info kernel: [ 65.003754] ag71xx-legacy 19000000.eth eth0: entered promiscuous mode
Sat Nov 16 00:33:15 2024 kern.info kernel: [ 65.068047] br-lan: port 1(eth0.1) entered blocking state
Sat Nov 16 00:33:15 2024 kern.info kernel: [ 65.073651] br-lan: port 1(eth0.1) entered forwarding state
Sat Nov 16 00:33:15 2024 daemon.notice netifd: Interface 'lan' is enabled
Sat Nov 16 00:33:15 2024 daemon.notice netifd: Interface 'lan' is setting up now
Sat Nov 16 00:33:15 2024 daemon.notice netifd: Interface 'lan' is now up
Sat Nov 16 00:33:15 2024 daemon.notice netifd: bridge 'br-lan' link is up
Sat Nov 16 00:33:15 2024 daemon.notice netifd: Interface 'lan' has link connectivity
Sat Nov 16 00:33:15 2024 daemon.notice netifd: Interface 'loopback' is enabled
Sat Nov 16 00:33:15 2024 daemon.notice netifd: Interface 'loopback' is setting up now
Sat Nov 16 00:33:15 2024 daemon.notice netifd: Interface 'loopback' is now up
Sat Nov 16 00:33:15 2024 daemon.notice netifd: Interface 'wwan' is setting up now
Sat Nov 16 00:33:15 2024 daemon.notice netifd: bridge 'br-lan' link is down
Sat Nov 16 00:33:15 2024 daemon.notice netifd: Interface 'lan' has link connectivity loss
Sat Nov 16 00:33:15 2024 daemon.notice netifd: Network device 'eth0' link is up
Sat Nov 16 00:33:15 2024 daemon.notice netifd: VLAN 'eth0.1' link is up
Sat Nov 16 00:33:15 2024 daemon.notice netifd: bridge 'br-lan' link is up
Sat Nov 16 00:33:15 2024 daemon.notice netifd: Interface 'lan' has link connectivity
Sat Nov 16 00:33:15 2024 daemon.notice netifd: Network device 'lo' link is up
Sat Nov 16 00:33:15 2024 daemon.notice netifd: Interface 'loopback' has link connectivity
Sat Nov 16 00:33:17 2024 user.notice firewall: Reloading firewall due to ifup of lan (br-lan)
' does not exist or is not an array/objectifd: wwan (2891): WARNING: Variable '
Sat Nov 16 00:33:18 2024 daemon.notice netifd: wwan (2891): Unsupported modem
Sat Nov 16 00:33:19 2024 daemon.notice netifd: wwan (3095): Stopping network wwan
' does not exist or is not an array/objectifd: wwan (3095): WARNING: Variable '
Sat Nov 16 00:33:21 2024 daemon.notice netifd: wwan (3095): Unsupported modem
Sat Nov 16 00:33:22 2024 daemon.err collectd[3121]: plugin_load: plugin "cpu" successfully loaded.
Sat Nov 16 00:33:22 2024 daemon.notice netifd: Interface 'wwan' is now down
Sat Nov 16 00:33:22 2024 daemon.err collectd[3121]: plugin_load: plugin "interface" successfully loaded.
Sat Nov 16 00:33:22 2024 daemon.err collectd[3121]: plugin_load: plugin "iwinfo" successfully loaded.
Sat Nov 16 00:33:22 2024 daemon.err collectd[3121]: plugin_load: plugin "load" successfully loaded.
Sat Nov 16 00:33:22 2024 daemon.info dnsmasq[1]: started, version 2.90 cachesize 1000
Sat Nov 16 00:33:22 2024 daemon.info dnsmasq[1]: DNS service limited to local subnets
Sat Nov 16 00:33:22 2024 daemon.info dnsmasq[1]: compile time options: IPv6 GNU-getopt no-DBus UBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-nftset no-auth no-cryptohash no-DNSSEC no-ID loop-detect inotify dumpfile
Sat Nov 16 00:33:22 2024 daemon.info dnsmasq[1]: UBus support enabled: connected to system bus
Sat Nov 16 00:33:22 2024 daemon.info dnsmasq-dhcp[1]: DHCP, IP range 192.168.1.100 -- 192.168.1.249, lease time 12h
Sat Nov 16 00:33:22 2024 daemon.info dnsmasq[1]: using only locally-known addresses for test
Sat Nov 16 00:33:22 2024 daemon.info dnsmasq[1]: using only locally-known addresses for onion
Sat Nov 16 00:33:22 2024 daemon.info dnsmasq[1]: using only locally-known addresses for localhost
Sat Nov 16 00:33:22 2024 daemon.info dnsmasq[1]: using only locally-known addresses for local
Sat Nov 16 00:33:22 2024 daemon.info dnsmasq[1]: using only locally-known addresses for invalid
Sat Nov 16 00:33:22 2024 daemon.info dnsmasq[1]: using only locally-known addresses for bind
Sat Nov 16 00:33:22 2024 daemon.info dnsmasq[1]: using only locally-known addresses for lan
Sat Nov 16 00:33:22 2024 daemon.warn dnsmasq[1]: no servers found in /tmp/resolv.conf.d/resolv.conf.auto, will retry
Sat Nov 16 00:33:22 2024 daemon.info dnsmasq[1]: read /etc/hosts - 12 names
Sat Nov 16 00:33:22 2024 daemon.info dnsmasq[1]: read /tmp/hosts/dhcp.cfg01411c - 4 names
Sat Nov 16 00:33:22 2024 daemon.info dnsmasq-dhcp[1]: read /etc/ethers - 0 addresses
Sat Nov 16 00:33:22 2024 daemon.err collectd[3121]: plugin_load: plugin "memory" successfully loaded.
Sat Nov 16 00:33:23 2024 daemon.warn odhcpd[2519]: No default route present, overriding ra_lifetime to 0!
Sat Nov 16 00:33:23 2024 daemon.info dnsmasq[1]: read /etc/hosts - 12 names
Sat Nov 16 00:33:23 2024 daemon.info dnsmasq[1]: read /tmp/hosts/dhcp.cfg01411c - 4 names
Sat Nov 16 00:33:23 2024 daemon.info dnsmasq[1]: read /tmp/hosts/odhcpd - 0 names
Sat Nov 16 00:33:23 2024 daemon.info dnsmasq-dhcp[1]: read /etc/ethers - 0 addresses
Sat Nov 16 00:33:23 2024 daemon.err collectd[3121]: plugin_load: plugin "rrdtool" successfully loaded.
Sat Nov 16 00:33:23 2024 daemon.err collectd[3121]: rrdtool plugin: RRASingle = true: creating only AVERAGE RRAs
Sat Nov 16 00:33:24 2024 daemon.err nlbwmon[2963]: The netlink receive buffer size of 524288 bytes will be capped to 180224 bytes
Sat Nov 16 00:33:24 2024 daemon.err nlbwmon[2963]: by the kernel. The net.core.rmem_max sysctl limit needs to be raised to
Sat Nov 16 00:33:24 2024 daemon.info dnsmasq[1]: read /etc/hosts - 12 names
Sat Nov 16 00:33:24 2024 daemon.info dnsmasq[1]: read /tmp/hosts/dhcp.cfg01411c - 4 names
Sat Nov 16 00:33:24 2024 daemon.info dnsmasq[1]: read /tmp/hosts/odhcpd - 2 names
Sat Nov 16 00:33:24 2024 daemon.info dnsmasq-dhcp[1]: read /etc/ethers - 0 addresses
Sat Nov 16 00:33:24 2024 user.notice ucitrack: Setting up /etc/config/luci-splash reload dependency on /etc/config/firewall
Sat Nov 16 00:33:24 2024 daemon.err collectd[3121]: plugin_load: plugin "sensors" successfully loaded.
Sat Nov 16 00:33:24 2024 daemon.err collectd[3121]: Initialization complete, entering read-loop.
Sat Nov 16 00:33:24 2024 user.notice ucitrack: Setting up /etc/config/qos reload dependency on /etc/config/firewall
Sat Nov 16 00:33:24 2024 user.notice ucitrack: Setting up /etc/config/miniupnpd reload dependency on /etc/config/firewall
Sat Nov 16 00:33:24 2024 daemon.err nlbwmon[2963]: at least 524288 in order to sucessfully set the desired receive buffer size!
Sat Nov 16 00:33:24 2024 user.notice nlbwmon: Reloading nlbwmon due to ifup of lan (br-lan)
Sat Nov 16 00:33:25 2024 user.notice ucitrack: Setting up /etc/config/odhcpd reload dependency on /etc/config/dhcp
Sat Nov 16 00:33:26 2024 user.notice ucitrack: Setting up /etc/config/dhcp reload dependency on /etc/config/network
Sat Nov 16 00:33:26 2024 user.notice ucitrack: Setting up /etc/config/network reload dependency on /etc/config/wireless
Sat Nov 16 00:33:27 2024 user.notice ucitrack: Setting up non-init /etc/config/fstab reload handler: /sbin/block mount
Sat Nov 16 00:33:27 2024 user.notice ucitrack: Setting up /etc/config/system reload trigger for non-procd /etc/init.d/led
Sat Nov 16 00:33:27 2024 user.notice ucitrack: Setting up /etc/config/luci_statistics reload dependency on /etc/config/system
Sat Nov 16 00:33:27 2024 user.notice ucitrack: Setting up /etc/config/dhcp reload dependency on /etc/config/system
Sat Nov 16 00:33:30 2024 user.notice nlbwmon: Reloading nlbwmon due to ifup of loopback (lo)
Sat Nov 16 00:33:31 2024 daemon.notice ksmbd: Stopping Ksmbd userspace service.
Sat Nov 16 00:33:31 2024 daemon.notice ksmbd: Starting Ksmbd userspace service.
Sat Nov 16 00:33:39 2024 daemon.warn odhcpd[2519]: No default route present, overriding ra_lifetime to 0!
Sat Nov 16 00:33:40 2024 daemon.info procd: - init complete -
Sat Nov 16 00:33:48 2024 user.info adblock-4.2.2-r8[2436]: adblock is currently disabled, please set the config option 'adb_enabled' to '1' to use this service
Sat Nov 16 00:33:55 2024 daemon.warn odhcpd[2519]: No default route present, overriding ra_lifetime to 0!
Sat Nov 16 00:33:58 2024 daemon.info dnsmasq-dhcp[1]: DHCPDISCOVER(br-lan) 192.168.1.234 30:9c:23:93:51:87
Sat Nov 16 00:33:58 2024 daemon.info dnsmasq-dhcp[1]: DHCPOFFER(br-lan) 192.168.1.234 30:9c:23:93:51:87
Sat Nov 16 00:33:58 2024 daemon.info dnsmasq-dhcp[1]: DHCPREQUEST(br-lan) 192.168.1.234 30:9c:23:93:51:87
Sat Nov 16 00:33:58 2024 daemon.info dnsmasq-dhcp[1]: DHCPACK(br-lan) 192.168.1.234 30:9c:23:93:51:87 DESKTOP-NVM960L
Sat Nov 16 00:34:21 2024 authpriv.info dropbear[4780]: Child connection from 192.168.1.234:57110
Sat Nov 16 00:34:22 2024 authpriv.notice dropbear[4780]: Auth succeeded with blank password for 'root' from 192.168.1.234:57110Sat Nov 16 00:33:17 2024 user.notice firewall: Reloading firewall due to ifup of lan (br-lan)
' does not exist or is not an array/objectifd: wwan (2891): WARNING: Variable '
Sat Nov 16 00:33:18 2024 daemon.notice netifd: wwan (2891): Unsupported modem
Sat Nov 16 00:33:19 2024 daemon.notice netifd: wwan (3095): Stopping network wwan
' does not exist or is not an array/objectifd: wwan (3095): WARNING: Variable '
Sat Nov 16 00:33:21 2024 daemon.notice netifd: wwan (3095): Unsupported modem
Ciekawie się robi. Pokaż
gcom -d /dev/ttyACM0 -s /etc/gcom/getcardinfo.gcomStrony Poprzednia 1 … 43 44 45 46 47 … 50 Następna
Zaloguj się lub zarejestruj by napisać odpowiedź
eko.one.pl → Sprzęt / Hardware → ZTE MF286R - OpenWrt
Forum oparte o PunBB, wspierane przez Informer Technologies, Inc