1 (edytowany przez ambrozy5 2024-08-12 18:38:51)

Temat: Cudy AP3000 openwrt

Pozwoliłem sobie utworzyć temat o tym AP.
Mamy do czynienia z bardzo fajną konstrukcją opartą na :
Procesor : Mediatek MT7981BA
Ram: 512MB DDR4!
FLash: 256MB
Sieć : Realtek rtl8221b 2.5Gb POE+ / bra kelementow na drugi port 1Gb z cpu !


dwa zdjęcia ze środka na początek
https://i.imgur.com/Kqic0Yd.jpeg
https://i.imgur.com/IAKeSPp.jpeg

Dom : router https://i.imgur.com/IuB6Zwy.png | TP-LINK T1700G-28TQ |Zyxel XGS-1210-12 | 6x Ruckus r310 unleashed  + Ruckus icx7150-c12p | Truenas scale 124TB 25Gb| Xpenology 12TB | apc smart ups 750 lcd smile 100Mb/s - 25Gb/s
Podróżne : GL.Inet MT3000  +1TB hdd
Działka : rb260gs 1j wdm 1Gb+ ruckus r310 + nb m5 + kilka kamer ip  + panel 285Wp + lifepo4 12v 60Ah .

2

Odp: Cudy AP3000 openwrt

GPL'e do pobrania: https://www.cudy.com/pages/download-center/ap3000-1-0

DTSy są, więc w sumie to kwestia tylko przeportowania tego na aktualne źródła (soft cudy oparty jest na 21.02)

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

3

Odp: Cudy AP3000 openwrt

konsola nieaktywna sad nie da się przerwać łądowania os

Dom : router https://i.imgur.com/IuB6Zwy.png | TP-LINK T1700G-28TQ |Zyxel XGS-1210-12 | 6x Ruckus r310 unleashed  + Ruckus icx7150-c12p | Truenas scale 124TB 25Gb| Xpenology 12TB | apc smart ups 750 lcd smile 100Mb/s - 25Gb/s
Podróżne : GL.Inet MT3000  +1TB hdd
Działka : rb260gs 1j wdm 1Gb+ ruckus r310 + nb m5 + kilka kamer ip  + panel 285Wp + lifepo4 12v 60Ah .

4

Odp: Cudy AP3000 openwrt

Poszukaj czy w obwodzie np, rezystora nie brakuje.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

5 (edytowany przez ambrozy5 2024-08-12 19:28:41)

Odp: Cudy AP3000 openwrt

nie brakuje bo znaki wysla do terminala ale nie reaguje, probowalem esc, del, spacebar, strzałki dół, góra i nic,
https://pastebin.com/NgRfNkqk

Dom : router https://i.imgur.com/IuB6Zwy.png | TP-LINK T1700G-28TQ |Zyxel XGS-1210-12 | 6x Ruckus r310 unleashed  + Ruckus icx7150-c12p | Truenas scale 124TB 25Gb| Xpenology 12TB | apc smart ups 750 lcd smile 100Mb/s - 25Gb/s
Podróżne : GL.Inet MT3000  +1TB hdd
Działka : rb260gs 1j wdm 1Gb+ ruckus r310 + nb m5 + kilka kamer ip  + panel 285Wp + lifepo4 12v 60Ah .

6

Odp: Cudy AP3000 openwrt

W sensie że przerwać nie ma jak.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

7 (edytowany przez ambrozy5 2024-08-12 19:52:51)

Odp: Cudy AP3000 openwrt

Cezary napisał/a:

W sensie że przerwać nie ma jak.

tak,

edit: 3 sek wcisnac reset i jest konsola uboota big_smile , teraz jakis intramfs odpale


U-Boot 2022.07-rc3 (Sep 01 2023 - 07:34:59 +0000), Build: jenkins-AP3000-19

CPU:   MediaTek MT7981
Model: mt7981-rfb
DRAM:  512 MiB
Core:  44 devices, 20 uclasses, devicetree: embed

Initializing NMBM ...
spi-nand: spi_nand spi_nand@0: Micron SPI NAND was found.
spi-nand: spi_nand spi_nand@0: 256 MiB, block size: 128 KiB, page size: 2048, OO                B size: 128
Could not find a valid device for nmbm0
Signature found at block 2047 [0x0ffe0000]
First info table with writecount 0 found in block 1920
Second info table with writecount 0 found in block 1923
NMBM has been successfully attached

Loading Environment from MTD... *** Warning - bad CRC, using default environment

In:    serial@11002000
Out:   serial@11002000
Err:   serial@11002000
Net:
Warning: ethernet@15100000 (eth0) using random MAC address - 2a:47:e7:7e:0e:cd
eth0: ethernet@15100000
gpio: pin 39 (gpio 39) value is 0
RESET button is pressed for:  2 second(s)

*** Upgrading oem fit Firmware ***

ethernet@15100000 Waiting for PHY auto negotiation to complete......... TIMEOUT                 !
MT7981> help
?         - alias for 'help'
base      - print or set address offset
bdinfo    - print Board Info structure
blkcache  - block cache diagnostics and control
boot      - boot default, i.e., run 'bootcmd'
bootd     - boot default, i.e., run 'bootcmd'
bootefi   - Boots an EFI payload from memory
bootelf   - Boot from an ELF image in memory
bootflow  - Boot flows
booti     - boot Linux kernel 'Image' format from memory
bootm     - boot application image from memory
bootmenu  - ANSI terminal bootmenu
bootp     - boot image via network using BOOTP/TFTP protocol
bootvx    - Boot vxWorks from an ELF image
button    - manage buttons
cmp       - memory compare
coninfo   - print console devices and information
cp        - memory copy
crc32     - checksum calculation
custombtn - custom button check
echo      - echo args to console
editenv   - edit environment variable
env       - environment handling commands
erase     - erase FLASH memory
fdt       - flattened device tree utility commands
flinfo    - print FLASH memory information
go        - start application at address 'addr'
gpio      - query and control gpio pins
gzwrite   - unzip and write memory to block device
help      - print command description/usage
iminfo    - print header information for application image
imxtract  - extract a part of a multi-image
itest     - return true/false on integer compare
led       - manage LEDs
ledblink  - led blink
loadb     - load binary file over serial line (kermit mode)
loads     - load S-Record file over serial line
loadx     - load binary file over serial line (xmodem mode)
loady     - load binary file over serial line (ymodem mode)
loop      - infinite loop on address range
lzmadec   - lzma uncompress a memory region
md        - memory display
mm        - memory modify (auto-incrementing address)
mtd       - MTD utils
mtkautoboot- Display MediaTek bootmenu
mtkboardboot- Boot MTK firmware
mtkload   - MTK image loading utility
mtkupgrade- MTK firmware/bootloader upgrading utility
mtkupgrade_oem- MTK firmware/bootloader upgrading utility for oem firmware
mw        - memory write (fill)
nand      - NAND utility
net       - NET sub-system
nfs       - boot image via network using NFS protocol
nm        - memory modify (constant address)
nmbm      - NMBM utility commands
panic     - Panic with optional message
ping      - send ICMP ECHO_REQUEST to network host
pinmux    - show pin-controller muxing
printenv  - print environment variables
protect   - enable or disable FLASH write protection
pwm       - control pwm channels
random    - fill memory with random pattern
reset     - Perform RESET of the CPU
run       - run commands in an environment variable
saveenv   - save environment variables to persistent storage
setenv    - set environment variables
setexpr   - set environment variable as the result of eval expression
sf        - SPI flash sub-system
sleep     - delay execution for some time
smc       - Issue a Secure Monitor Call
source    - run script from memory
tftpboot  - boot image via network using TFTP protocol
unlz4     - lz4 uncompress a memory region
unzip     - unzip a memory region
version   - print monitor, compiler and linker version
MT7981>
?         - alias for 'help'
base      - print or set address offset
bdinfo    - print Board Info structure
blkcache  - block cache diagnostics and control
boot      - boot default, i.e., run 'bootcmd'
bootd     - boot default, i.e., run 'bootcmd'
bootefi   - Boots an EFI payload from memory
bootelf   - Boot from an ELF image in memory
bootflow  - Boot flows
booti     - boot Linux kernel 'Image' format from memory
bootm     - boot application image from memory
bootmenu  - ANSI terminal bootmenu
bootp     - boot image via network using BOOTP/TFTP protocol
bootvx    - Boot vxWorks from an ELF image
button    - manage buttons
cmp       - memory compare
coninfo   - print console devices and information
cp        - memory copy
crc32     - checksum calculation
custombtn - custom button check
echo      - echo args to console
editenv   - edit environment variable
env       - environment handling commands
erase     - erase FLASH memory
fdt       - flattened device tree utility commands
flinfo    - print FLASH memory information
go        - start application at address 'addr'
gpio      - query and control gpio pins
gzwrite   - unzip and write memory to block device
help      - print command description/usage
iminfo    - print header information for application image
imxtract  - extract a part of a multi-image
itest     - return true/false on integer compare
led       - manage LEDs
ledblink  - led blink
loadb     - load binary file over serial line (kermit mode)
loads     - load S-Record file over serial line
loadx     - load binary file over serial line (xmodem mode)
loady     - load binary file over serial line (ymodem mode)
loop      - infinite loop on address range
lzmadec   - lzma uncompress a memory region
md        - memory display
mm        - memory modify (auto-incrementing address)
mtd       - MTD utils
mtkautoboot- Display MediaTek bootmenu
mtkboardboot- Boot MTK firmware
mtkload   - MTK image loading utility
mtkupgrade- MTK firmware/bootloader upgrading utility
mtkupgrade_oem- MTK firmware/bootloader upgrading utility for oem firmware
mw        - memory write (fill)
nand      - NAND utility
net       - NET sub-system
nfs       - boot image via network using NFS protocol
nm        - memory modify (constant address)
nmbm      - NMBM utility commands
panic     - Panic with optional message
ping      - send ICMP ECHO_REQUEST to network host
pinmux    - show pin-controller muxing
printenv  - print environment variables
protect   - enable or disable FLASH write protection
pwm       - control pwm channels
random    - fill memory with random pattern
reset     - Perform RESET of the CPU
run       - run commands in an environment variable
saveenv   - save environment variables to persistent storage
setenv    - set environment variables
setexpr   - set environment variable as the result of eval expression
sf        - SPI flash sub-system
sleep     - delay execution for some time
smc       - Issue a Secure Monitor Call
source    - run script from memory
tftpboot  - boot image via network using TFTP protocol
unlz4     - lz4 uncompress a memory region
unzip     - unzip a memory region
version   - print monitor, compiler and linker version
MT7981> printenv
baudrate=115200
bootdelay=2
ethact=ethernet@15100000
ethaddr=2a:47:e7:7e:0e:cd
fdtcontroladdr=5ffc3a00
ipaddr=192.168.1.112
loadaddr=0x46000000
netmask=255.255.255.0
serverip=192.168.1.88
stderr=serial@11002000
stdin=serial@11002000
stdout=serial@11002000

Environment size: 257/131068 bytes
MT7981> tftpboot openwrt-mediatek-filogic-cudy_tr3000-v1-initramfs-kernel.bin
ethernet@15100000 Waiting for PHY auto negotiation to complete......... TIMEOUT !
MT7981> tftpboot openwrt-mediatek-filogic-cudy_tr3000-v1-initramfs-kernel.bin
ethernet@15100000 Waiting for PHY auto negotiation to complete......... TIMEOUT !
MT7981> setenv bootfile initramfs-kernel.bin
MT7981> tftpboot
ethernet@15100000 Waiting for PHY auto negotiation to complete......... TIMEOUT !
MT7981> tftpboot
ethernet@15100000 Waiting for PHY auto negotiation to complete......... TIMEOUT !
MT7981> tftpboot
ethernet@15100000 Waiting for PHY auto negotiation to complete......... TIMEOUT !
MT7981>
Dom : router https://i.imgur.com/IuB6Zwy.png | TP-LINK T1700G-28TQ |Zyxel XGS-1210-12 | 6x Ruckus r310 unleashed  + Ruckus icx7150-c12p | Truenas scale 124TB 25Gb| Xpenology 12TB | apc smart ups 750 lcd smile 100Mb/s - 25Gb/s
Podróżne : GL.Inet MT3000  +1TB hdd
Działka : rb260gs 1j wdm 1Gb+ ruckus r310 + nb m5 + kilka kamer ip  + panel 285Wp + lifepo4 12v 60Ah .

8

Odp: Cudy AP3000 openwrt

Nie negocjuje ci połączenia. Do czego podłączyłeś jego ethernet?

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

9

Odp: Cudy AP3000 openwrt

podpinałem przez switcha z poe  to samo co bezposrednio, ustawialem w sterowniku karty 10 /100/1000/2500/ auto i to samo. moze jakiejs zmiennej w env brakuje ? nawet ping nie dziala

Dom : router https://i.imgur.com/IuB6Zwy.png | TP-LINK T1700G-28TQ |Zyxel XGS-1210-12 | 6x Ruckus r310 unleashed  + Ruckus icx7150-c12p | Truenas scale 124TB 25Gb| Xpenology 12TB | apc smart ups 750 lcd smile 100Mb/s - 25Gb/s
Podróżne : GL.Inet MT3000  +1TB hdd
Działka : rb260gs 1j wdm 1Gb+ ruckus r310 + nb m5 + kilka kamer ip  + panel 285Wp + lifepo4 12v 60Ah .

10

Odp: Cudy AP3000 openwrt

Ale by były szopki gdyby się okazało że uboot odnosi się do tego drugiego ethernetu którego nie ma.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

11 (edytowany przez ambrozy5 2024-08-12 20:55:29)

Odp: Cudy AP3000 openwrt

no jestem zly na nich, z tego co widze to eth dopiero sie laczy jak os sie zaladuje..

edit: dodałem do env bootfile=initramfs-kernel.bin i zapisalem, po reboocie jak wcisne reset to chce te plik z ip 192.168.1.88 ale eth śpi. jeden kroczek do przodu.

Dom : router https://i.imgur.com/IuB6Zwy.png | TP-LINK T1700G-28TQ |Zyxel XGS-1210-12 | 6x Ruckus r310 unleashed  + Ruckus icx7150-c12p | Truenas scale 124TB 25Gb| Xpenology 12TB | apc smart ups 750 lcd smile 100Mb/s - 25Gb/s
Podróżne : GL.Inet MT3000  +1TB hdd
Działka : rb260gs 1j wdm 1Gb+ ruckus r310 + nb m5 + kilka kamer ip  + panel 285Wp + lifepo4 12v 60Ah .

12

Odp: Cudy AP3000 openwrt

widze ze utknelismy na tym samym Ambrozy ;-)

13

Odp: Cudy AP3000 openwrt

A czy firmware ten 2.1.1 zmienia cos w wersji u-boota? jak myslisz

14

Odp: Cudy AP3000 openwrt

Kusi podlutować te wolne miejsce na port ETH ;-) pare rezystorkow....moze zadziała?

15

Odp: Cudy AP3000 openwrt

Wgralem nowy odrazu ale taki sam efekt, downgrade polecial i jak widac, mozna by podpatrzec z bpi schematy czy coś, niby nie duzo elementow ale sa bardzo tyciaczne sad

Dom : router https://i.imgur.com/IuB6Zwy.png | TP-LINK T1700G-28TQ |Zyxel XGS-1210-12 | 6x Ruckus r310 unleashed  + Ruckus icx7150-c12p | Truenas scale 124TB 25Gb| Xpenology 12TB | apc smart ups 750 lcd smile 100Mb/s - 25Gb/s
Podróżne : GL.Inet MT3000  +1TB hdd
Działka : rb260gs 1j wdm 1Gb+ ruckus r310 + nb m5 + kilka kamer ip  + panel 285Wp + lifepo4 12v 60Ah .

16

Odp: Cudy AP3000 openwrt

Czy w ich sofcie jest dostęp do ssh? Jeżeli tak to spoko, wystarczy zrobić odpowiedni sysupgrade.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

17

Odp: Cudy AP3000 openwrt

Cezary napisał/a:

Czy w ich sofcie jest dostęp do ssh? Jeżeli tak to spoko, wystarczy zrobić odpowiedni sysupgrade.

nie ma, otwarte jedynie 53,80 i 443  sad może jakieś ukryte menu w ichiejszym sofcie jest ? dropbeara nie udalo sie wywolac z gui ściezka ze zwyklego openwrt.

Dom : router https://i.imgur.com/IuB6Zwy.png | TP-LINK T1700G-28TQ |Zyxel XGS-1210-12 | 6x Ruckus r310 unleashed  + Ruckus icx7150-c12p | Truenas scale 124TB 25Gb| Xpenology 12TB | apc smart ups 750 lcd smile 100Mb/s - 25Gb/s
Podróżne : GL.Inet MT3000  +1TB hdd
Działka : rb260gs 1j wdm 1Gb+ ruckus r310 + nb m5 + kilka kamer ip  + panel 285Wp + lifepo4 12v 60Ah .

18

Odp: Cudy AP3000 openwrt

a ja probowalem przeslac binarke initram przez terminal (kermit chyba poszedl), tylko zawiesilo mi sie - moze macie pomysl gdzie uboot ma ta binarke zaladowac (adres?) - bo moze to jest ostatnia droga wgrania?

19

Odp: Cudy AP3000 openwrt

Pewnie pod zmienną loadaddr

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

20

Odp: Cudy AP3000 openwrt

Ja za to kończę wsparcie dla AP3000 Outdoor. Ale tam nie da się rozebrać obudowy i trzeba kombinować bez seriala.

Mam i używam: Fujitsu Futro S720, Netgear R6220, Unielec U7621-06, TP-Linki 1043 V1, V2, Linksysy EA7500v2, AeroHive AP350, Linksys EA8500, ZTE MF286d.
Mam: D-Linki DWR-921, DWR-118, DWR-116, TP-Link WDR-4900 v1, Checkpoint L-50, Linksysy 1900ACS, LB-Link BL-W1200,

21

Odp: Cudy AP3000 openwrt

widze ze cos tu sie moze zadziac chyba
https://github.com/Linaro1985/openwrt/c … 0da18a0b43

22 (edytowany przez ambrozy5 2024-08-13 00:30:35)

Odp: Cudy AP3000 openwrt

zyxel nwa50ax pro jest bardzo podobny 

MT7981> atnz 665ACGE1C0.bin
Using ethernet1@15100000 device
TFTP from server 192.168.42.42; our IP address is 192.168.42.1
Filename '665ACGE1C0.bin'.

Na stronie cudy "For AP3000, it is because there is no recover feature. If the device is work abnormal. You can’t get it back"... El żenuasjon.

Dom : router https://i.imgur.com/IuB6Zwy.png | TP-LINK T1700G-28TQ |Zyxel XGS-1210-12 | 6x Ruckus r310 unleashed  + Ruckus icx7150-c12p | Truenas scale 124TB 25Gb| Xpenology 12TB | apc smart ups 750 lcd smile 100Mb/s - 25Gb/s
Podróżne : GL.Inet MT3000  +1TB hdd
Działka : rb260gs 1j wdm 1Gb+ ruckus r310 + nb m5 + kilka kamer ip  + panel 285Wp + lifepo4 12v 60Ah .

23 (edytowany przez szyper 2024-08-13 01:01:40)

Odp: Cudy AP3000 openwrt

Udało mi sie uruchomic openwrt -na razie z obrazu TR3000 - niestety na jakies 15 sekund.

ethernet@15100000 Waiting for PHY auto negotiation to complete......... TIMEOUT !
MT7981> setenv bootfile initramfs-kernel.bin
MT7981> loadx
## Ready for binary (xmodem) download to 0x46000000 at 115200 bps...
C## Total Size      = 0x006f62c4 = 7299780 Bytes
## Start Addr      = 0x46000000
MT7981> bootm
## Loading kernel from FIT Image at 46000000 ...
   Using 'config-1' configuration
   Trying 'kernel-1' kernel subimage
     Description:  ARM64 OpenWrt Linux-5.15.162
     Type:         Kernel Image
     Compression:  lzma compressed
     Data Start:   0x460000ec
     Data Size:    3779836 Bytes = 3.6 MiB
     Architecture: AArch64
     OS:           Linux
     Load Address: 0x48000000
     Entry Point:  0x48000000
     Hash algo:    crc32
     Hash value:   b736c825
     Hash algo:    sha1
     Hash value:   2fc05ba58e3317134cc541a2cd331f7e54ae5060
   Verifying Hash Integrity ... crc32+ sha1+ OK
## Loading ramdisk from FIT Image at 46000000 ...
   Using 'config-1' configuration
   Trying 'initrd-1' ramdisk subimage
     Description:  ARM64 OpenWrt cudy_tr3000-v1 initrd
     Type:         RAMDisk Image
     Compression:  Unknown Compression
     Data Start:   0x4639af20
     Data Size:    3495464 Bytes = 3.3 MiB
     Architecture: AArch64
     OS:           Linux
     Load Address: unavailable
     Entry Point:  unavailable
     Hash algo:    crc32
     Hash value:   ba5afe98
     Hash algo:    sha1
     Hash value:   a8eb27d4ca1d75d96edcba7defd0bccc038f89fb
   Verifying Hash Integrity ... crc32+ sha1+ OK
WARNING: 'compression' nodes for ramdisks are deprecated, please fix your .its file!
## Loading fdt from FIT Image at 46000000 ...
   Using 'config-1' configuration
   Trying 'fdt-1' fdt subimage
     Description:  ARM64 OpenWrt cudy_tr3000-v1 device tree blob
     Type:         Flat Device Tree
     Compression:  uncompressed
     Data Start:   0x466f0654
     Data Size:    22332 Bytes = 21.8 KiB
     Architecture: AArch64
     Hash algo:    crc32
     Hash value:   2b8bf20b
     Hash algo:    sha1
     Hash value:   f10462de83eee6ea32303c4a187d538cb9bf0832
   Verifying Hash Integrity ... crc32+ sha1+ OK
   Booting using the fdt blob at 0x466f0654
   Uncompressing Kernel Image
   Loading Ramdisk to 5f4a5000, end 5f7fa628 ... OK
   Loading Device Tree to 000000005f49c000, end 000000005f4a473b ... OK

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[    0.000000] Linux version 5.15.162 (builder@buildhost) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 12.3.0 r24012-d8dd03c46f) 12.3.0, GNU ld (GNU Binutils) 2.40.0) #0 SMP Mon Jul 15 22:14:18 2024
[    0.000000] Machine model: Cudy TR3000 v1
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000040000000-0x000000005fffffff]
[    0.000000]   DMA32    empty
[    0.000000]   Normal   empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000040000000-0x0000000042ffffff]
[    0.000000]   node   0: [mem 0x0000000043000000-0x000000004302ffff]
[    0.000000]   node   0: [mem 0x0000000043030000-0x0000000047c7ffff]
[    0.000000]   node   0: [mem 0x0000000047c80000-0x0000000047ffffff]
[    0.000000]   node   0: [mem 0x0000000048000000-0x000000005fffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000005fffffff]
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.1 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] psci: SMC Calling Convention v1.2
[    0.000000] percpu: Embedded 18 pages/cpu s33112 r8192 d32424 u73728
[    0.000000] pcpu-alloc: s33112 r8192 d32424 u73728 alloc=18*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1
[    0.000000] Detected VIPT I-cache on CPU0
[    0.000000] CPU features: detected: GIC system register CPU interface
[    0.000000] CPU features: kernel page table isolation disabled by kernel configuration
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 129024
[    0.000000] Kernel command line:
[    0.000000] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes, linear)
[    0.000000] Inode-cache hash table entries: 32768 (order: 6, 262144 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 495112K/524288K available (8384K kernel code, 906K rwdata, 1488K rodata, 448K init, 300K bss, 29176K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] rcu: Hierarchical RCU implementation.
[    0.000000] rcu:     RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000]  Tracing variant of Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[    0.000000] GICv3: GIC: Using split EOI/Deactivate mode
[    0.000000] GICv3: 640 SPIs implemented
[    0.000000] GICv3: 0 Extended SPIs implemented
[    0.000000] GICv3: Distributor has no Range Selector support
[    0.000000] Root IRQ handler: 0xffffffc008010090
[    0.000000] GICv3: 16 PPIs implemented
[    0.000000] GICv3: CPU0: found redistributor 0 region 0:0x000000000c080000
[    0.000000] arch_timer: cp15 timer(s) running at 13.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2ff89eacb, max_idle_ns: 440795202429 ns
[    0.000001] sched_clock: 56 bits at 13MHz, resolution 76ns, wraps every 4398046511101ns
[    0.000144] Calibrating delay loop (skipped), value calculated using timer frequency.. 26.00 BogoMIPS (lpj=130000)
[    0.000154] pid_max: default: 32768 minimum: 301
[    0.000439] Mount-cache hash table entries: 1024 (order: 1, 8192 bytes, linear)
[    0.000450] Mountpoint-cache hash table entries: 1024 (order: 1, 8192 bytes, linear)
[    0.001754] rcu: Hierarchical SRCU implementation.
[    0.002121] smp: Bringing up secondary CPUs ...
[    0.002444] Detected VIPT I-cache on CPU1
[    0.002471] GICv3: CPU1: found redistributor 1 region 0:0x000000000c0a0000
[    0.002499] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[    0.002566] smp: Brought up 1 node, 2 CPUs
[    0.002580] SMP: Total of 2 processors activated.
[    0.002585] CPU features: detected: 32-bit EL0 Support
[    0.002590] CPU features: detected: CRC32 instructions
[    0.002616] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching
[    0.002681] CPU: All CPU(s) started at EL2
[    0.002692] alternatives: patching kernel code
[    0.005979] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.006001] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
[    0.006143] pinctrl core: initialized pinctrl subsystem
[    0.006985] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[    0.007288] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations
[    0.007316] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[    0.007345] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[    0.007683] thermal_sys: Registered thermal governor 'fair_share'
[    0.007687] thermal_sys: Registered thermal governor 'bang_bang'
[    0.007692] thermal_sys: Registered thermal governor 'step_wise'
[    0.007696] thermal_sys: Registered thermal governor 'user_space'
[    0.007877] ASID allocator initialised with 65536 entries
[    0.008336] pstore: Registered ramoops as persistent store backend
[    0.008342] ramoops: using 0x10000@0x42ff0000, ecc: 0
[    0.018992] cryptd: max_cpu_qlen set to 1000
[    0.021499] SCSI subsystem initialized
[    0.021686] libata version 3.00 loaded.
[    0.022844] clocksource: Switched to clocksource arch_sys_counter
[    0.023484] NET: Registered PF_INET protocol family
[    0.023584] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear)
[    0.024090] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear)
[    0.024113] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.024123] TCP established hash table entries: 4096 (order: 3, 32768 bytes, linear)
[    0.024154] TCP bind hash table entries: 4096 (order: 4, 65536 bytes, linear)
[    0.024206] TCP: Hash tables configured (established 4096 bind 4096)
[    0.024272] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.024290] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.024422] NET: Registered PF_UNIX/PF_LOCAL protocol family
[    0.024452] PCI: CLS 0 bytes, default 64
[    0.024733] Unpacking initramfs...
[    0.026952] workingset: timestamp_bits=46 max_order=17 bucket_order=0
[    0.030799] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.030817] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.066529] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[    0.068289] pwm-mediatek 10048000.pwm: clock: top fail: -517
[    0.078642] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.080836] printk: console [ttyS0] disabled
[    0.101025] 11002000.serial: ttyS0 at MMIO 0x11002000 (irq = 18, base_baud = 2500000) is a ST16650V2
[    0.726357] printk: console [ttyS0] enabled
[    0.731378] cacheinfo: Unable to detect cache hierarchy for CPU 0
[    0.741656] loop: module loaded
[    0.744839] Loading iSCSI transport class v2.0-870.
[    0.763824] spi spi0.0: setup: ignoring unsupported mode bits a00
[    0.771177] spi-nand spi0.0: calibration result: 0x2
[    0.776337] spi-nand spi0.0: Micron SPI NAND was found.
[    0.781564] spi-nand spi0.0: 256 MiB, block size: 128 KiB, page size: 2048, OOB size: 128
[    0.790417] Signature found at block 2047 [0x0ffe0000]
[    0.795594] NMBM management region starts at block 1920 [0x0f000000]
[    0.804516] First info table with writecount 2 found in block 1920
[    0.818275] Second info table with writecount 2 found in block 1923
[    0.824571] NMBM has been successfully attached
[    1.049442] Freeing initrd memory: 3412K
[    1.060018] 6 fixed-partitions partitions found on MTD device spi0.0
[    1.066687] Creating 6 MTD partitions on "spi0.0":
[    1.071478] 0x000000000000-0x000000100000 : "BL2"
[    1.077496] 0x000000100000-0x000000180000 : "u-boot-env"
[    1.083711] 0x000000180000-0x000000380000 : "Factory"
[    1.091042] 0x000000380000-0x0000003c0000 : "bdinfo"
[    1.097146] 0x0000003c0000-0x0000005c0000 : "FIP"
[    1.104154] 0x0000005c0000-0x0000045c0000 : "ubi"
[    1.675977] mtk_soc_eth 15100000.ethernet eth0: mediatek frame engine at 0xffffffc009100000, irq 82
[    1.685862] mtk_soc_eth 15100000.ethernet eth1: mediatek frame engine at 0xffffffc009100000, irq 82
[    1.695511] i2c_dev: i2c /dev entries driver
[    1.701109] mtk-wdt 1001c000.watchdog: Watchdog enabled (timeout=31 sec, nowayout=0)
[    1.709985] NET: Registered PF_INET6 protocol family
[    1.716119] Segment Routing with IPv6
[    1.719802] In-situ OAM (IOAM) with IPv6
[    1.723794] NET: Registered PF_PACKET protocol family
[    1.728871] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    1.742059] 8021q: 802.1Q VLAN Support v1.8
[    1.747254] pstore: Using crash dump compression: deflate
[    1.761566] phy phy-usb-phy@11e10000.1: type_sw - reg 0x218, index 0
[    1.769070] UBI: auto-attach mtd5
[    1.772393] ubi0: default fastmap pool size: 25
[    1.776946] ubi0: default fastmap WL pool size: 12
[    1.781724] ubi0: attaching mtd5
[    2.201195] ubi0: scanning is finished
[    2.214321] ubi0 warning: 0xffffffc00856d794: cannot reserve enough PEBs for bad PEB handling, reserved 36, need 38
[    2.225326] ubi0: attached mtd5 (name "ubi", size 64 MiB)
[    2.230728] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    2.237611] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    2.244392] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[    2.251339] ubi0: good PEBs: 512, bad PEBs: 0, corrupted PEBs: 0
[    2.257336] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
[    2.264548] ubi0: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 1693553699
[    2.273668] ubi0: available PEBs: 0, total reserved PEBs: 512, PEBs reserved for bad PEB handling: 36
[    2.282884] ubi0: background thread "ubi_bgt0d" started, PID 435
[    2.290833] block ubiblock0_1: created from ubi0:1(rootfs)
[    2.296363] ubiblock: device ubiblock0_1 (rootfs) set to be root filesystem
[    2.303555] clk: Disabling unused clocks
[    2.308027] Freeing unused kernel memory: 448K
[    2.312504] Run /init as init process
[    2.316165]   with arguments:
[    2.319120]     /init
[    2.321380]   with environment:
[    2.324512]     HOME=/
[    2.326859]     TERM=linux
[    2.514264] init: Console is alive
[    2.517802] init: - watchdog -
[    2.524893] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    2.536778] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    2.551522] init: - preinit -
[    2.603152] random: procd: uninitialized urandom read (4 bytes read)
[    2.671036] mtk_soc_eth 15100000.ethernet eth1: PHY [mdio-bus:00] driver [MediaTek MT7981 PHY] (irq=POLL)
[    2.685754] mtk_soc_eth 15100000.ethernet eth1: configuring for phy/gmii link mode
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    4.758045] procd: - early -
[    4.761010] procd: - watchdog -
[    5.291216] procd: - watchdog -
[    5.294548] procd: - ubus -
[    5.299931] random: ubusd: uninitialized urandom read (4 bytes read)
[    5.347098] random: ubusd: uninitialized urandom read (4 bytes read)
[    5.353662] random: ubusd: uninitialized urandom read (4 bytes read)
[    5.361174] procd: - init -
Please press Enter to activate this console.
[    5.520851] kmodloader: loading kernel modules from /etc/modules.d/*
[    5.534221] crypto-safexcel 10320000.crypto: EIP97:230(0,1,4,4)-HIA:270(0,5,5),PE:150/433(alg:7fcdfc00)/0/0/0
[    5.550767] Loading modules backported from Linux version v6.1.97-0-g7753af06eebfb
[    5.558372] Backport generated by backports.git v6.1.97-1-0-g2431d56e
[    5.731198] urngd: v1.0.2 started.
[    5.893360] random: crng init done
[    5.896762] random: 23 urandom warning(s) missed due to ratelimiting
[    5.915518] mt798x-wmac 18000000.wifi: Direct firmware load for mediatek/mt7981_rom_patch.bin failed with error -2
[    5.925876] mt798x-wmac 18000000.wifi: Falling back to sysfs fallback for: mediatek/mt7981_rom_patch.bin
[    5.958022] mt798x-wmac: probe of 18000000.wifi failed with error -12
[    5.984836] PPP generic driver version 2.4.2
[    5.990317] NET: Registered PF_PPPOX protocol family
[    5.999097] kmodloader: done loading kernel modules from /etc/modules.d/*



BusyBox v1.36.1 (2024-07-15 22:14:18 UTC) built-in shell (ash)

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 -----------------------------------------------------
 OpenWrt 23.05.4, r24012-d8dd03c46f
 -----------------------------------------------------
=== WARNING! =====================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.
--------------------------------------------------
root@(none):/#
root@(none):/# ls
bin      init     mnt      rom      sys      var
dev      lib      overlay  root     tmp      www
etc      lib64    proc     sbin     usr
root@OpenWrt:/# df -h
Filesystem                Size      Used Available Use% Mounted on
tmpfs                   243.6M     18.7M    225.0M   8% /
tmpfs                   243.6M     40.0K    243.6M   0% /tmp
tmpfs                   512.0K         0    512.0K   0% /dev
root@OpenWrt:/# [   10.497711] mtk_soc_eth 15100000.ethernet eth1: PHY [mdio-bus:00] driver [MediaTek MT7981 PHY] (irq=POLL)
[   10.512789] mtk_soc_eth 15100000.ethernet eth1: configuring for phy/gmii link mode
[   10.521561] br-lan: port 1(eth1) entered blocking state
[   10.526860] br-lan: port 1(eth1) entered disabled state
[   10.532282] device eth1 entered promiscuous mode
[   10.783332] mtk_soc_eth 15100000.ethernet eth0: PHY [mdio-bus:01] driver [RTL8221B-VB-CG 2.5Gbps PHY] (irq=POLL)
[   10.793565] mtk_soc_eth 15100000.ethernet eth0: configuring for phy/2500base-x link mode

root@OpenWrt:/# dmesg
[    0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[    0.000000] Linux version 5.15.162 (builder@buildhost) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 12.3.0 r24012-d8dd03c46f) 12.3.0, GNU ld (GNU Binutils) 2.40.0) #0 SMP Mon Jul 15 22:14:18 2024
[    0.000000] M[   13.923409] mtk_soc_eth 15100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
achine model: Cu[   13.932083] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
dy TR3000 v1
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000040000000-0x000000005fffffff]
[    0.000000]   DMA32    empty
[    0.000000]   Normal   empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000040000000-0x0000000042ffffff]
[    0.000000]   node   0: [mem 0x0000000043000000-0x000000004302ffff]
[    0.000000]   node   0: [mem 0x0000000043030000-0x0000000047c7ffff]
[    0.000000]   node   0: [mem 0x0000000047c80000-0x0000000047ffffff]
[    0.000000]   node   0: [mem 0x0000000048000000-0x000000005fffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000005fffffff]
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.1 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] psci: SMC Calling Convention v1.2
[    0.000000] percpu: Embedded 18 pages/cpu s33112 r8192 d32424 u73728
[    0.000000] pcpu-alloc: s33112 r8192 d32424 u73728 alloc=18*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1
[    0.000000] Detected VIPT I-cache on CPU0
[    0.000000] CPU features: detected: GIC system register CPU interface
[    0.000000] CPU features: kernel page table isolation disabled by kernel configuration
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 129024
[    0.000000] Kernel command line:
[    0.000000] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes, linear)
[    0.000000] Inode-cache hash table entries: 32768 (order: 6, 262144 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 495112K/524288K available (8384K kernel code, 906K rwdata, 1488K rodata, 448K init, 300K bss, 29176K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] rcu: Hierarchical RCU implementation.
[    0.000000] rcu:     RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000]  Tracing variant of Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[    0.000000] GICv3: GIC: Using split EOI/Deactivate mode
[    0.000000] GICv3: 640 SPIs implemented
[    0.000000] GICv3: 0 Extended SPIs implemented
[    0.000000] GICv3: Distributor has no Range Selector support
[    0.000000] Root IRQ handler: 0xffffffc008010090
[    0.000000] GICv3: 16 PPIs implemented
[    0.000000] GICv3: CPU0: found redistributor 0 region 0:0x000000000c080000
[    0.000000] arch_timer: cp15 timer(s) running at 13.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2ff89eacb, max_idle_ns: 440795202429 ns
[    0.000001] sched_clock: 56 bits at 13MHz, resolution 76ns, wraps every 4398046511101ns
[    0.000144] Calibrating delay loop (skipped), value calculated using timer frequency.. 26.00 BogoMIPS (lpj=130000)
[    0.000154] pid_max: default: 32768 minimum: 301
[    0.000439] Mount-cache hash table entries: 1024 (order: 1, 8192 bytes, linear)
[    0.000450] Mountpoint-cache hash table entries: 1024 (order: 1, 8192 bytes, linear)
[    0.001754] rcu: Hierarchical SRCU implementation.
[    0.002121] smp: Bringing up secondary CPUs ...
[    0.002444] Detected VIPT I-cache on CPU1
[    0.002471] GICv3: CPU1: found redistributor 1 region 0:0x000000000c0a0000
[    0.002499] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[    0.002566] smp: Brought up 1 node, 2 CPUs
[    0.002580] SMP: Total of 2 processors activated.
[    0.002585] CPU features: detected: 32-bit EL0 Support
[    0.002590] CPU features: detected: CRC32 instructions
[    0.002616] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching
[    0.002681] CPU: All CPU(s) started at EL2
[    0.002692] alternatives: patching kernel code
[    0.005979] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.006001] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
[    0.006143] pinctrl core: initialized pinctrl subsystem
[    0.006985] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[    0.007288] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations
[    0.007316] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[    0.007345] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[    0.007683] thermal_sys: Registered thermal governor 'fair_share'
[    0.007687] thermal_sys: Registered thermal governor 'bang_bang'
[    0.007692] thermal_sys: Registered thermal governor 'step_wise'
[    0.007696] thermal_sys: Registered thermal governor 'user_space'
[    0.007877] ASID allocator initialised with 65536 entries
[    0.008336] pstore: Registered ramoops as persistent store backend
[    0.008342] ramoops: using 0x10000@0x42ff0000, ecc: 0
[    0.018992] cryptd: max_cpu_qlen set to 1000
[    0.021499] SCSI subsystem initialized
[    0.021686] libata version 3.00 loaded.
[    0.022844] clocksource: Switched to clocksource arch_sys_counter
[    0.023484] NET: Registered PF_INET protocol family
[    0.023584] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear)
[    0.024090] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear)
[    0.024113] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.024123] TCP established hash table entries: 4096 (order: 3, 32768 bytes, linear)
[    0.024154] TCP bind hash table entries: 4096 (order: 4, 65536 bytes, linear)
[    0.024206] TCP: Hash tables configured (established 4096 bind 4096)
[    0.024272] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.024290] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.024422] NET: Registered PF_UNIX/PF_LOCAL protocol family
[    0.024452] PCI: CLS 0 bytes, default 64
[    0.024733] Unpacking initramfs...
[    0.026952] workingset: timestamp_bits=46 max_order=17 bucket_order=0
[    0.030799] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.030817] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.066529] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[    0.068289] pwm-mediatek 10048000.pwm: clock: top fail: -517
[    0.078642] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.080836] printk: console [ttyS0] disabled
[    0.101025] 11002000.serial: ttyS0 at MMIO 0x11002000 (irq = 18, base_baud = 2500000) is a ST16650V2
[    0.726357] printk: console [ttyS0] enabled
[    0.731378] cacheinfo: Unable to detect cache hierarchy for CPU 0
[    0.741656] loop: module loaded
[    0.744839] Loading iSCSI transport class v2.0-870.
[    0.763824] spi spi0.0: setup: ignoring unsupported mode bits a00
[    0.771177] spi-nand spi0.0: calibration result: 0x2
[    0.776337] spi-nand spi0.0: Micron SPI NAND was found.
[    0.781564] spi-nand spi0.0: 256 MiB, block size: 128 KiB, page size: 2048, OOB size: 128
[    0.790417] Signature found at block 2047 [0x0ffe0000]
[    0.795594] NMBM management region starts at block 1920 [0x0f000000]
[    0.804516] First info table with writecount 2 found in block 1920
[    0.818275] Second info table with writecount 2 found in block 1923
[    0.824571] NMBM has been successfully attached
[    1.049442] Freeing initrd memory: 3412K
[    1.060018] 6 fixed-partitions partitions found on MTD device spi0.0
[    1.066687] Creating 6 MTD partitions on "spi0.0":
[    1.071478] 0x000000000000-0x000000100000 : "BL2"
[    1.077496] 0x000000100000-0x000000180000 : "u-boot-env"
[    1.083711] 0x000000180000-0x000000380000 : "Factory"
[    1.091042] 0x000000380000-0x0000003c0000 : "bdinfo"
[    1.097146] 0x0000003c0000-0x0000005c0000 : "FIP"
[    1.104154] 0x0000005c0000-0x0000045c0000 : "ubi"
[    1.675977] mtk_soc_eth 15100000.ethernet eth0: mediatek frame engine at 0xffffffc009100000, irq 82
[    1.685862] mtk_soc_eth 15100000.ethernet eth1: mediatek frame engine at 0xffffffc009100000, irq 82
[    1.695511] i2c_dev: i2c /dev entries driver
[    1.701109] mtk-wdt 1001c000.watchdog: Watchdog enabled (timeout=31 sec, nowayout=0)
[    1.709985] NET: Registered PF_INET6 protocol family
[    1.716119] Segment Routing with IPv6
[    1.719802] In-situ OAM (IOAM) with IPv6
[    1.723794] NET: Registered PF_PACKET protocol family
[    1.728871] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    1.742059] 8021q: 802.1Q VLAN Support v1.8
[    1.747254] pstore: Using crash dump compression: deflate
[    1.761566] phy phy-usb-phy@11e10000.1: type_sw - reg 0x218, index 0
[    1.769070] UBI: auto-attach mtd5
[    1.772393] ubi0: default fastmap pool size: 25
[    1.776946] ubi0: default fastmap WL pool size: 12
[    1.781724] ubi0: attaching mtd5
[    2.201195] ubi0: scanning is finished
[    2.214321] ubi0 warning: 0xffffffc00856d794: cannot reserve enough PEBs for bad PEB handling, reserved 36, need 38
[    2.225326] ubi0: attached mtd5 (name "ubi", size 64 MiB)
[    2.230728] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    2.237611] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    2.244392] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[    2.251339] ubi0: good PEBs: 512, bad PEBs: 0, corrupted PEBs: 0
[    2.257336] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
[    2.264548] ubi0: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 1693553699
[    2.273668] ubi0: available PEBs: 0, total reserved PEBs: 512, PEBs reserved for bad PEB handling: 36
[    2.282884] ubi0: background thread "ubi_bgt0d" started, PID 435
[    2.290833] block ubiblock0_1: created from ubi0:1(rootfs)
[    2.296363] ubiblock: device ubiblock0_1 (rootfs) set to be root filesystem
[    2.303555] clk: Disabling unused clocks
[    2.308027] Freeing unused kernel memory: 448K
[    2.312504] Run /init as init process
[    2.316165]   with arguments:
[    2.319120]     /init
[    2.321380]   with environment:
[    2.324512]     HOME=/
[    2.326859]     TERM=linux
[    2.514264] init: Console is alive
[    2.517802] init: - watchdog -
[    2.524893] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    2.536778] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    2.551522] init: - preinit -
[    2.603152] random: procd: uninitialized urandom read (4 bytes read)
[    2.671036] mtk_soc_eth 15100000.ethernet eth1: PHY [mdio-bus:00] driver [MediaTek MT7981 PHY] (irq=POLL)
[    2.685754] mtk_soc_eth 15100000.ethernet eth1: configuring for phy/gmii link mode
[    4.758045] procd: - early -
[    4.761010] procd: - watchdog -
[    5.291216] procd: - watchdog -
[    5.294548] procd: - ubus -
[    5.299931] random: ubusd: uninitialized urandom read (4 bytes read)
[    5.347098] random: ubusd: uninitialized urandom read (4 bytes read)
[    5.353662] random: ubusd: uninitialized urandom read (4 bytes read)
[    5.361174] procd: - init -
[    5.520851] kmodloader: loading kernel modules from /etc/modules.d/*
[    5.534221] crypto-safexcel 10320000.crypto: EIP97:230(0,1,4,4)-HIA:270(0,5,5),PE:150/433(alg:7fcdfc00)/0/0/0
[    5.550767] Loading modules backported from Linux version v6.1.97-0-g7753af06eebfb
[    5.558372] Backport generated by backports.git v6.1.97-1-0-g2431d56e
[    5.731198] urngd: v1.0.2 started.
[    5.893360] random: crng init done
[    5.896762] random: 23 urandom warning(s) missed due to ratelimiting
[    5.915518] mt798x-wmac 18000000.wifi: Direct firmware load for mediatek/mt7981_rom_patch.bin failed with error -2
[    5.925876] mt798x-wmac 18000000.wifi: Falling back to sysfs fallback for: mediatek/mt7981_rom_patch.bin
[    5.958022] mt798x-wmac: probe of 18000000.wifi failed with error -12
[    5.984836] PPP generic driver version 2.4.2
[    5.990317] NET: Registered PF_PPPOX protocol family
[    5.999097] kmodloader: done loading kernel modules from /etc/modules.d/*
[   10.497711] mtk_soc_eth 15100000.ethernet eth1: PHY [mdio-bus:00] driver [MediaTek MT7981 PHY] (irq=POLL)
[   10.512789] mtk_soc_eth 15100000.ethernet eth1: configuring for phy/gmii link mode
[   10.521561] br-lan: port 1(eth1) entered blocking state
[   10.526860] br-lan: port 1(eth1) entered disabled state
[   10.532282] device eth1 entered promiscuous mode
[   10.783332] mtk_soc_eth 15100000.ethernet eth0: PHY [mdio-bus:01] driver [RTL8221B-VB-CG 2.5Gbps PHY] (irq=POLL)
[   10.793565] mtk_soc_eth 15100000.ethernet eth0: configuring for phy/2500base-x link mode
root@OpenWrt:/#
root@OpenWrt:/# ifconfig
br-lan    Link encap:Ethernet  HWaddr 80:AF:CA:44:8F:1A
          inet addr:192.168.1.1  Bcast:192.168.1.255  Mask:255.255.255.0
          inet6 addr: fd3d:2036:e9d0::1/60 Scope:Global
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

eth0      Link encap:Ethernet  HWaddr 80:AF:CA:44:8F:1B
          inet6 addr: fe80::82af:caff:fe44:8f1b/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:131 errors:0 dropped:3 overruns:0 frame:0
          TX packets:12 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:25620 (25.0 KiB)  TX bytes:2126 (2.0 KiB)
          Interrupt:82

eth1      Link encap:Ethernet  HWaddr 80:AF:CA:44:8F:1A
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
          Interrupt:82

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:65536  Metric:1
          RX packets:32 errors:0 dropped:0 overruns:0 frame:0
          TX packets:32 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:2496 (2.4 KiB)  TX bytes:2496 (2.4 KiB)

root@OpenWrt:/#
r
root@OpenWrt:/#
root@OpenWrt:/#
root@OpenWrt:/# [   32.482855] usb-vbus: disabling

root@OpenWrt:/#
root@OpenWrt:/#
....

i tu nastepuje restart do domyslnego obrazu firmowego.
Myslicie ze jest sens zrobic szybki sysupgrade i to coś da?
Ew, czy skompilowac openwrt z commit linaro, ktory juz podpial dts itp. i ten wgrac?

24

Odp: Cudy AP3000 openwrt

Dokładnie, skompiluj tamto i jak działa - czyszczenie i do openwrt.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

25 (edytowany przez ambrozy5 2024-08-13 17:25:34)

Odp: Cudy AP3000 openwrt

obawiam się, że będzie nam równiez potrzebny firmware przechodni tak jak Królik miał do ap3000 outdoor a te głąby nie chcą się podzielic ... ta , mila im napisalem i piłeczke odbili że no way.

Dom : router https://i.imgur.com/IuB6Zwy.png | TP-LINK T1700G-28TQ |Zyxel XGS-1210-12 | 6x Ruckus r310 unleashed  + Ruckus icx7150-c12p | Truenas scale 124TB 25Gb| Xpenology 12TB | apc smart ups 750 lcd smile 100Mb/s - 25Gb/s
Podróżne : GL.Inet MT3000  +1TB hdd
Działka : rb260gs 1j wdm 1Gb+ ruckus r310 + nb m5 + kilka kamer ip  + panel 285Wp + lifepo4 12v 60Ah .