1 Temat przez tygrysss (edytowany przez tygrysss 2024-08-03 14:16:35)

  • Zarejestrowany: 2015-06-19
  • Posty: 423

Temat: AX3000T - jak tego nie robic + upewnienie się by zrobić to dobrze

Cześć,
kolejny już widzę post dot. tego urządzenia - chyba informacja o promocji na pewnej stronie, że można go dostać za ~120zł robi swoje.
Post ten jest w sumie informacją jak nie postępować podczas zmiany oprogramowywania na OpenWRT.
Robiąc to sugerowałem się https://openwrt.org/inbox/toh/xiaomi/ax3000t ale również na filmiku na YT (by mieć pogląd jak to wygląda). Wina moja - za szybko, gonił mnie czas, a w zasadzie jego brak.
Router odebrałem - soft 1.0.47, wgrałem ten rekomendowany - poszło ok. Dostęp do SSH, zgranie partycji 

nanddump -f /tmp/BL2.bin /dev/mtd1
nanddump -f /tmp/Nvram.bin /dev/mtd2
nanddump -f /tmp/Bdata.bin /dev/mtd3
nanddump -f /tmp/Factory.bin /dev/mtd4
nanddump -f /tmp/FIP.bin /dev/mtd5
nanddump -f /tmp/ubi.bin /dev/mtd8
nanddump -f /tmp/KF.bin /dev/mtd12

wrzucenie https://dl.eko.one.pl/luci/openwrt-23.0 … actory.ubi i wstało na openwrt.
Wstało, ale zauważyłem, że bez WIFI. Nigdzie w zakładce nie było informacji o sieciach bezprzewodowych (na ori działało).
Nie przejąłem się tym za bardzo w tamtym momencie.
Pytanie - czemu nie widać było interfejsu bezprzewodowego?
Mówię, ok czas na uboot. No i wgrałem najpierw https://dl.eko.one.pl/luci/openwrt-23.0 … actory.ubi i router już nie wstał. Wpadł w bootloop. Nie działała procedura TFTP.
No to co - otwieram. Szybki UART no i co zrobiłem:

 

  *** U-Boot Boot Menu ***

     1. Startup system (Default)
     2. Startup firmware0
     3. Startup firmware1
     4. Upgrade firmware
     5. Upgrade ATF BL2
     6. Upgrade ATF FIP
     7. Upgrade single image
     8. Load image
     0. U-Boot console


  Press UP/DOWN to move, ENTER to select, ESC/CTRL+C to quit

*** Loading image ***

Input load address: 0x46000000                                                0
detect button reset released!
Reading from 0x0 to 0x4f7fdd7c, size 0x4 ... OK
Boot failure detected on both systems
Reading from 0x0 to 0x4f7fdd7c, size 0x4 ... OK
Saving Environment to MTD... Erasing on MTD device 'nmbm0'... OK
Writing to MTD device 'nmbm0'... OK
OK
Booting System 0, sys1_failed = 61, sys2_failed = 8
ubi0: attaching mtd9
ubi0: scanning is finished
ubi0: attached mtd9 (name "ubi", size 34 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 272, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 0, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 3/2, WL threshold: 4096, image sequence number: 1503784899
ubi0: available PEBs: 249, total reserved PEBs: 23, PEBs reserved for bad PEB handling: 19
Reading from volume 'kernel' to 0x46000000, size 0x0 ... *** Cannot find volume 'kernel' ***
resetting ...

F0: 102B 0000
FA: 1040 0000
FA: 1040 0000 [0200]
F9: 0000 0000
V0: 0000 0000 [0001]
00: 0000 0000
BP: 2400 0041 [0000]
G0: 1190 0000
EC: 0000 0000 [1000]
T0: 0000 024F [010F]
Jump to BL

NOTICE:  BL2: v2.6(release):e233a3d581-dirty
NOTICE:  BL2: Built : 06:23:27, Jul 30 2023
NOTICE:  WDT: disabled
NOTICE:  EMI: Using DDR3 settings

dump toprgu registers data:
1001c000 | 00000000 0000ffe0 00000000 00000000
1001c010 | 00000fff 00000000 00f00000 00000000
1001c020 | 00000000 00000000 00000000 00000000
1001c030 | 003c0003 003c0003 00000000 00000000
1001c040 | 00000000 00000000 00000000 00000000
1001c050 | 00000000 00000000 00000000 00000000
1001c060 | 00000000 00000000 00000000 00000000
1001c070 | 00000000 00000000 00000000 00000000
1001c080 | 00000000 00000000 00000000 00000000

dump drm registers data:
1001d000 | 00000000 00000000 00000000 00000000
1001d010 | 00000000 00000000 00000000 00000000
1001d020 | 00000000 00000000 00000000 00000000
1001d030 | 00a003f1 000000ff 00100000 00000000
1001d040 | 00027e71 000200a0 00020303 000000ff
1001d050 | 00000000 00000000 00000000 00000000
1001d060 | 00000002 00000000 00000000 00000000
drm: 500 = 0xc
[DDR Reserve] ddr reserve mode not be enabled yet
DDR RESERVE Success 0
[EMI] ComboMCP not ready, using default setting
BYTE_swap:0
BYTE_swap:0
Window Sum 632, worse bit 0, min window 76
Window Sum 604, worse bit 11, min window 72
Window Sum 522, worse bit 1, min window 64
Window Sum 458, worse bit 10, min window 54
Window Sum 464, worse bit 8, min window 56
Window Sum 524, worse bit 1, min window 64
Window Sum 468, worse bit 11, min window 56
Window Sum 474, worse bit 11, min window 56
Window Sum 482, worse bit 8, min window 58
NOTICE:  EMI: Detected DRAM size: 256MB
NOTICE:  EMI: complex R/W mem test passed
NOTICE:  CPU: MT7981 (1300MHz)
NOTICE:  SPI_NAND parses attributes from parameter page.
NOTICE:  SPI_NAND Detected ID 0xc8
NOTICE:  Page size 2048, Block size 131072, size 134217728
NOTICE:  Initializing NMBM ...
NOTICE:  Signature found at block 1023 [0x07fe0000]
NOTICE:  First info table with writecount 0 found in block 960
NOTICE:  Second info table with writecount 0 found in block 963
NOTICE:  NMBM has been successfully attached in read-only mode
NOTICE:  BL2: Booting BL31
NOTICE:  BL31: v2.6(release):e233a3d581-dirty
NOTICE:  BL31: Built : 06:23:27, Jul 30 2023
NOTICE:  Hello BL31!!!
In:    serial@11002000
Out:   serial@11002000
Err:   serial@11002000
Net:   eth0: ethernet@15100000

  *** U-Boot Boot Menu ***

     1. Startup system (Default)
     2. Startup firmware0
     3. Startup firmware1
     4. Upgrade firmware
     5. Upgrade ATF BL2
     6. Upgrade ATF FIP
     7. Upgrade single image
     8. Load image
     0. U-Boot console


  Press UP/DOWN to move, ENTER to select, ESC/CTRL+C to quit
detect button reset released!
Reading from 0x0 to 0x4f7fdd7c, size 0x4 ... OK
Boot failure detected on both systems
Reading from 0x0 to 0x4f7fdd7c, size 0x4 ... OK
Saving Environment to MTD... Erasing on MTD device 'nmbm0'... OK
Writing to MTD device 'nmbm0'... OK
OK
Booting System 0, sys1_failed = 62, sys2_failed = 8
ubi0: attaching mtd9
ubi0: scanning is finished
ubi0: attached mtd9 (name "ubi", size 34 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 272, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 0, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 3/2, WL threshold: 4096, image sequence number: 1503784899
ubi0: available PEBs: 249, total reserved PEBs: 23, PEBs reserved for bad PEB handling: 19
Reading from volume 'kernel' to 0x46000000, size 0x0 ... *** Cannot find volume 'kernel' ***
resetting ...

F0: 102B 0000
FA: 1040 0000
FA: 1040 0000 [0200]
F9: 0000 0000
V0: 0000 0000 [0001]
00: 0000 0000
BP: 2400 0041 [0000]
G0: 1190 0000
EC: 0000 0000 [1000]
T0: 0000 024F [010F]
Jump to BL

NOTICE:  BL2: v2.6(release):e233a3d581-dirty
NOTICE:  BL2: Built : 06:23:27, Jul 30 2023
NOTICE:  WDT: disabled
NOTICE:  EMI: Using DDR3 settings

dump toprgu registers data:
1001c000 | 00000000 0000ffe0 00000000 00000000
1001c010 | 00000fff 00000000 00f00000 00000000
1001c020 | 00000000 00000000 00000000 00000000
1001c030 | 003c0003 003c0003 00000000 00000000
1001c040 | 00000000 00000000 00000000 00000000
1001c050 | 00000000 00000000 00000000 00000000
1001c060 | 00000000 00000000 00000000 00000000
1001c070 | 00000000 00000000 00000000 00000000
1001c080 | 00000000 00000000 00000000 00000000

dump drm registers data:
1001d000 | 00000000 00000000 00000000 00000000
1001d010 | 00000000 00000000 00000000 00000000
1001d020 | 00000000 00000000 00000000 00000000
1001d030 | 00a003f1 000000ff 00100000 00000000
1001d040 | 00027e71 000200a0 00020303 000000ff
1001d050 | 00000000 00000000 00000000 00000000
1001d060 | 00000002 00000000 00000000 00000000
drm: 500 = 0xc
[DDR Reserve] ddr reserve mode not be enabled yet
DDR RESERVE Success 0
[EMI] ComboMCP not ready, using default setting
BYTE_swap:0
BYTE_swap:0
Window Sum 620, worse bit 0, min window 76
Window Sum 612, worse bit 8, min window 76
Window Sum 532, worse bit 0, min window 66
Window Sum 470, worse bit 11, min window 56
Window Sum 480, worse bit 8, min window 58
Window Sum 488, worse bit 10, min window 58
Window Sum 486, worse bit 8, min window 60
NOTICE:  EMI: Detected DRAM size: 256MB
NOTICE:  EMI: complex R/W mem test passed
NOTICE:  CPU: MT7981 (1300MHz)
NOTICE:  SPI_NAND parses attributes from parameter page.
NOTICE:  SPI_NAND Detected ID 0xc8
NOTICE:  Page size 2048, Block size 131072, size 134217728
NOTICE:  Initializing NMBM ...
NOTICE:  Signature found at block 1023 [0x07fe0000]
NOTICE:  First info table with writecount 0 found in block 960
NOTICE:  Second info table with writecount 0 found in block 963
NOTICE:  NMBM has been successfully attached in read-only mode
NOTICE:  BL2: Booting BL31
NOTICE:  BL31: v2.6(release):e233a3d581-dirty
NOTICE:  BL31: Built : 06:23:27, Jul 30 2023
NOTICE:  Hello BL31!!!
In:    serial@11002000
Out:   serial@11002000
Err:   serial@11002000
Net:   eth0: ethernet@15100000

  *** U-Boot Boot Menu ***

     1. Startup system (Default)
     2. Startup firmware0
     3. Startup firmware1
     4. Upgrade firmware
     5. Upgrade ATF BL2
     6. Upgrade ATF FIP
     7. Upgrade single image
     8. Load image
     0. U-Boot console


  Press UP/DOWN to move, ENTER to select, ESC/CTRL+C to quit
detect button reset released!
Reading from 0x0 to 0x4f7fdd7c, size 0x4 ... OK
Boot failure detected on both systems
Reading from 0x0 to 0x4f7fdd7c, size 0x4 ... OK
Saving Environment to MTD... Erasing on MTD device 'nmbm0'... OK
Writing to MTD device 'nmbm0'... OK
OK
Booting System 0, sys1_failed = 63, sys2_failed = 8
ubi0: attaching mtd9
ubi0: scanning is finished
ubi0: attached mtd9 (name "ubi", size 34 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 272, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 0, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 3/2, WL threshold: 4096, image sequence number: 1503784899
ubi0: available PEBs: 249, total reserved PEBs: 23, PEBs reserved for bad PEB handling: 19
Reading from volume 'kernel' to 0x46000000, size 0x0 ... *** Cannot find volume 'kernel' ***
resetting ...

F0: 102B 0000
FA: 1040 0000
FA: 1040 0000 [0200]
F9: 0000 0000
V0: 0000 0000 [0001]
00: 0000 0000
BP: 2400 0041 [0000]
G0: 1190 0000
EC: 0000 0000 [1000]
T0: 0000 024F [010F]
Jump to BL

NOTICE:  BL2: v2.6(release):e233a3d581-dirty
NOTICE:  BL2: Built : 06:23:27, Jul 30 2023
NOTICE:  WDT: disabled
NOTICE:  EMI: Using DDR3 settings

dump toprgu registers data:
1001c000 | 00000000 0000ffe0 00000000 00000000
1001c010 | 00000fff 00000000 00f00000 00000000
1001c020 | 00000000 00000000 00000000 00000000
1001c030 | 003c0003 003c0003 00000000 00000000
1001c040 | 00000000 00000000 00000000 00000000
1001c050 | 00000000 00000000 00000000 00000000
1001c060 | 00000000 00000000 00000000 00000000
1001c070 | 00000000 00000000 00000000 00000000
1001c080 | 00000000 00000000 00000000 00000000

dump drm registers data:
1001d000 | 00000000 00000000 00000000 00000000
1001d010 | 00000000 00000000 00000000 00000000
1001d020 | 00000000 00000000 00000000 00000000
1001d030 | 00a003f1 000000ff 00100000 00000000
1001d040 | 00027e71 000200a0 00020303 000000ff
1001d050 | 00000000 00000000 00000000 00000000
1001d060 | 00000002 00000000 00000000 00000000
drm: 500 = 0xc
[DDR Reserve] ddr reserve mode not be enabled yet
DDR RESERVE Success 0
[EMI] ComboMCP not ready, using default setting
BYTE_swap:0
BYTE_swap:0
Window Sum 636, worse bit 0, min window 76
Window Sum 608, worse bit 11, min window 72
Window Sum 520, worse bit 0, min window 64
Window Sum 458, worse bit 10, min window 54
Window Sum 524, worse bit 0, min window 64
Window Sum 468, worse bit 10, min window 56
Window Sum 528, worse bit 1, min window 64
Window Sum 478, worse bit 10, min window 58
Window Sum 480, worse bit 10, min window 58
NOTICE:  EMI: Detected DRAM size: 256MB
NOTICE:  EMI: complex R/W mem test passed
NOTICE:  CPU: MT7981 (1300MHz)
NOTICE:  SPI_NAND parses attributes from parameter page.
NOTICE:  SPI_NAND Detected ID 0xc8
NOTICE:  Page size 2048, Block size 131072, size 134217728
NOTICE:  Initializing NMBM ...
NOTICE:  Signature found at block 1023 [0x07fe0000]
NOTICE:  First info table with writecount 0 found in block 960
NOTICE:  Second info table with writecount 0 found in block 963
NOTICE:  NMBM has been successfully attached in read-only mode
NOTICE:  BL2: Booting BL31
NOTICE:  BL31: v2.6(release):e233a3d581-dirty
NOTICE:  BL31: Built : 06:23:27, Jul 30 2023
NOTICE:  Hello BL31!!!
In:    serial@11002000
Out:   serial@11002000
Err:   serial@11002000
Net:   eth0: ethernet@15100000

  *** U-Boot Boot Menu ***

     1. Startup system (Default)
     2. Startup firmware0
     3. Startup firmware1
     4. Upgrade firmware
     5. Upgrade ATF BL2
     6. Upgrade ATF FIP
     7. Upgrade single image
     8. Load image
     0. U-Boot console


  Press UP/DOWN to move, ENTER to select, ESC/CTRL+C to quit
detect button reset released!
Reading from 0x0 to 0x4f7fdd7c, size 0x4 ... OK
Boot failure detected on both systems
Reading from 0x0 to 0x4f7fdd7c, size 0x4 ... OK
Saving Environment to MTD... Erasing on MTD device 'nmbm0'... OK
Writing to MTD device 'nmbm0'... OK
OK
Booting System 0, sys1_failed = 64, sys2_failed = 8
ubi0: attaching mtd9
ubi0: scanning is finished
ubi0: attached mtd9 (name "ubi", size 34 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 272, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 0, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 3/2, WL threshold: 4096, image sequence number: 1503784899
ubi0: available PEBs: 249, total reserved PEBs: 23, PEBs reserved for bad PEB handling: 19
Reading from volume 'kernel' to 0x46000000, size 0x0 ... *** Cannot find volume 'kernel' ***
resetting ...

F0: 102B 0000
FA: 1040 0000
FA: 1040 0000 [0200]
F9: 0000 0000
V0: 0000 0000 [0001]
00: 0000 0000
BP: 2400 0041 [0000]
G0: 1190 0000
EC: 0000 0000 [1000]
T0: 0000 024F [010F]
Jump to BL

NOTICE:  BL2: v2.6(release):e233a3d581-dirty
NOTICE:  BL2: Built : 06:23:27, Jul 30 2023
NOTICE:  WDT: disabled
NOTICE:  EMI: Using DDR3 settings

dump toprgu registers data:
1001c000 | 00000000 0000ffe0 00000000 00000000
1001c010 | 00000fff 00000000 00f00000 00000000
1001c020 | 00000000 00000000 00000000 00000000
1001c030 | 003c0003 003c0003 00000000 00000000
1001c040 | 00000000 00000000 00000000 00000000
1001c050 | 00000000 00000000 00000000 00000000
1001c060 | 00000000 00000000 00000000 00000000
1001c070 | 00000000 00000000 00000000 00000000
1001c080 | 00000000 00000000 00000000 00000000

dump drm registers data:
1001d000 | 00000000 00000000 00000000 00000000
1001d010 | 00000000 00000000 00000000 00000000
1001d020 | 00000000 00000000 00000000 00000000
1001d030 | 00a003f1 000000ff 00100000 00000000
1001d040 | 00027e71 000200a0 00020303 000000ff
1001d050 | 00000000 00000000 00000000 00000000
1001d060 | 00000002 00000000 00000000 00000000
drm: 500 = 0xc
[DDR Reserve] ddr reserve mode not be enabled yet
DDR RESERVE Success 0
[EMI] ComboMCP not ready, using default setting
BYTE_swap:0
BYTE_swap:0
Window Sum 624, worse bit 0, min window 76
Window Sum 620, worse bit 8, min window 76
Window Sum 532, worse bit 0, min window 66
Window Sum 470, worse bit 11, min window 56
Window Sum 486, worse bit 10, min window 58
Window Sum 490, worse bit 10, min window 58
Window Sum 490, worse bit 8, min window 60
Window Sum 492, worse bit 8, min window 60
NOTICE:  EMI: Detected DRAM size: 256MB
NOTICE:  EMI: complex R/W mem test passed
NOTICE:  CPU: MT7981 (1300MHz)
NOTICE:  SPI_NAND parses attributes from parameter page.
NOTICE:  SPI_NAND Detected ID 0xc8
NOTICE:  Page size 2048, Block size 131072, size 134217728
NOTICE:  Initializing NMBM ...
NOTICE:  Signature found at block 1023 [0x07fe0000]
NOTICE:  First info table with writecount 0 found in block 960
NOTICE:  Second info table with writecount 0 found in block 963
NOTICE:  NMBM has been successfully attached in read-only mode
NOTICE:  BL2: Booting BL31
NOTICE:  BL31: v2.6(release):e233a3d581-dirty
NOTICE:  BL31: Built : 06:23:27, Jul 30 2023
NOTICE:  Hello BL31!!!
In:    serial@11002000
Out:   serial@11002000
Err:   serial@11002000
Net:   eth0: ethernet@15100000

  *** U-Boot Boot Menu ***

     1. Startup system (Default)
     2. Startup firmware0
     3. Startup firmware1
     4. Upgrade firmware
     5. Upgrade ATF BL2
     6. Upgrade ATF FIP
     7. Upgrade single image
     8. Load image
     0. U-Boot console


  Press UP/DOWN to move, ENTER to select, ESC/CTRL+C to quit

*** Upgrading Firmware ***

Run image after upgrading? (Y/n): Available load methods:
    0 - TFTP client (Default)
    1 - Xmodem
    2 - Ymodem
    3 - Kermit
    4 - S-Record
    5 - RAM

Select (enter for default): 0

Input U-Boot's IP address: 192.168.10.1
Input TFTP server's IP address: 192.168.10.100
Input IP netmask: 255.255.255.0
Input file name:
*** Operation Aborted! ***
Hit any key to stop autoboot:  0
detect button reset released!
Reading from 0x0 to 0x4f7ff2cc, size 0x4 ... OK
Boot failure detected on both systems
Reading from 0x0 to 0x4f7ff2cc, size 0x4 ... OK
Saving Environment to MTD... Erasing on MTD device 'nmbm0'... OK
Writing to MTD device 'nmbm0'... OK
OK
Booting System 0, sys1_failed = 65, sys2_failed = 8
ubi0: attaching mtd9
ubi0: scanning is finished
ubi0: attached mtd9 (name "ubi", size 34 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 272, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 0, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 3/2, WL threshold: 4096, image sequence number: 1503784899
ubi0: available PEBs: 249, total reserved PEBs: 23, PEBs reserved for bad PEB handling: 19
Reading from volume 'kernel' to 0x46000000, size 0x0 ... *** Cannot find volume 'kernel' ***
resetting ...

F0: 102B 0000
FA: 1040 0000
FA: 1040 0000 [0200]
F9: 0000 0000
V0: 0000 0000 [0001]
00: 0000 0000
BP: 2400 0041 [0000]
G0: 1190 0000
EC: 0000 0000 [1000]
T0: 0000 024F [010F]
Jump to BL

NOTICE:  BL2: v2.6(release):e233a3d581-dirty
NOTICE:  BL2: Built : 06:23:27, Jul 30 2023
NOTICE:  WDT: disabled
NOTICE:  EMI: Using DDR3 settings

dump toprgu registers data:
1001c000 | 00000000 0000ffe0 00000000 00000000
1001c010 | 00000fff 00000000 00f00000 00000000
1001c020 | 00000000 00000000 00000000 00000000
1001c030 | 003c0003 003c0003 00000000 00000000
1001c040 | 00000000 00000000 00000000 00000000
1001c050 | 00000000 00000000 00000000 00000000
1001c060 | 00000000 00000000 00000000 00000000
1001c070 | 00000000 00000000 00000000 00000000
1001c080 | 00000000 00000000 00000000 00000000

dump drm registers data:
1001d000 | 00000000 00000000 00000000 00000000
1001d010 | 00000000 00000000 00000000 00000000
1001d020 | 00000000 00000000 00000000 00000000
1001d030 | 00a003f1 000000ff 00100000 00000000
1001d040 | 00027e71 000200a0 00020303 000000ff
1001d050 | 00000000 00000000 00000000 00000000
1001d060 | 00000002 00000000 00000000 00000000
drm: 500 = 0xc
[DDR Reserve] ddr reserve mode not be enabled yet
DDR RESERVE Success 0
[EMI] ComboMCP not ready, using default setting
BYTE_swap:0
BYTE_swap:0
Window Sum 612, worse bit 0, min window 72
Window Sum 612, worse bit 8, min window 76
Window Sum 524, worse bit 1, min window 64
Window Sum 474, worse bit 11, min window 56
Window Sum 480, worse bit 10, min window 58
Window Sum 482, worse bit 10, min window 58
Window Sum 490, worse bit 8, min window 60
NOTICE:  EMI: Detected DRAM size: 256MB
NOTICE:  EMI: complex R/W mem test passed
NOTICE:  CPU: MT7981 (1300MHz)
NOTICE:  SPI_NAND parses attributes from parameter page.
NOTICE:  SPI_NAND Detected ID 0xc8
NOTICE:  Page size 2048, Block size 131072, size 134217728
NOTICE:  Initializing NMBM ...
NOTICE:  Signature found at block 1023 [0x07fe0000]
NOTICE:  First info table with writecount 0 found in block 960
NOTICE:  Second info table with writecount 0 found in block 963
NOTICE:  NMBM has been successfully attached in read-only mode
NOTICE:  BL2: Booting BL31
NOTICE:  BL31: v2.6(release):e233a3d581-dirty
NOTICE:  BL31: Built : 06:23:27, Jul 30 2023
NOTICE:  Hello BL31!!!
In:    serial@11002000
Out:   serial@11002000
Err:   serial@11002000
Net:   eth0: ethernet@15100000

  *** U-Boot Boot Menu ***

     1. Startup system (Default)
     2. Startup firmware0
     3. Startup firmware1
     4. Upgrade firmware
     5. Upgrade ATF BL2
     6. Upgrade ATF FIP
     7. Upgrade single image
     8. Load image
     0. U-Boot console


  Press UP/DOWN to move, ENTER to select, ESC/CTRL+C to quit
detect button reset released!
Reading from 0x0 to 0x4f7fdd7c, size 0x4 ... OK
Boot failure detected on both systems
Reading from 0x0 to 0x4f7fdd7c, size 0x4 ... OK
Saving Environment to MTD... Erasing on MTD device 'nmbm0'... OK
Writing to MTD device 'nmbm0'... OK
OK
Booting System 0, sys1_failed = 66, sys2_failed = 8
ubi0: attaching mtd9
ubi0: scanning is finished
ubi0: attached mtd9 (name "ubi", size 34 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 272, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 0, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 3/2, WL threshold: 4096, image sequence number: 1503784899
ubi0: available PEBs: 249, total reserved PEBs: 23, PEBs reserved for bad PEB handling: 19
Reading from volume 'kernel' to 0x46000000, size 0x0 ... *** Cannot find volume 'kernel' ***
resetting ...

F0: 102B 0000
FA: 1040 0000
FA: 1040 0000 [0200]
F9: 0000 0000
V0: 0000 0000 [0001]
00: 0000 0000
BP: 2400 0041 [0000]
G0: 1190 0000
EC: 0000 0000 [1000]
T0: 0000 024F [010F]
Jump to BL

NOTICE:  BL2: v2.6(release):e233a3d581-dirty
NOTICE:  BL2: Built : 06:23:27, Jul 30 2023
NOTICE:  WDT: disabled
NOTICE:  EMI: Using DDR3 settings

dump toprgu registers data:
1001c000 | 00000000 0000ffe0 00000000 00000000
1001c010 | 00000fff 00000000 00f00000 00000000
1001c020 | 00000000 00000000 00000000 00000000
1001c030 | 003c0003 003c0003 00000000 00000000
1001c040 | 00000000 00000000 00000000 00000000
1001c050 | 00000000 00000000 00000000 00000000
1001c060 | 00000000 00000000 00000000 00000000
1001c070 | 00000000 00000000 00000000 00000000
1001c080 | 00000000 00000000 00000000 00000000

dump drm registers data:
1001d000 | 00000000 00000000 00000000 00000000
1001d010 | 00000000 00000000 00000000 00000000
1001d020 | 00000000 00000000 00000000 00000000
1001d030 | 00a003f1 000000ff 00100000 00000000
1001d040 | 00027e71 000200a0 00020303 000000ff
1001d050 | 00000000 00000000 00000000 00000000
1001d060 | 00000002 00000000 00000000 00000000
drm: 500 = 0xc
[DDR Reserve] ddr reserve mode not be enabled yet
DDR RESERVE Success 0
[EMI] ComboMCP not ready, using default setting
BYTE_swap:0
BYTE_swap:0
Window Sum 620, worse bit 0, min window 76
Window Sum 600, worse bit 11, min window 72
Window Sum 518, worse bit 0, min window 64
Window Sum 460, worse bit 10, min window 54
Window Sum 526, worse bit 1, min window 64
Window Sum 468, worse bit 10, min window 56
Window Sum 476, worse bit 11, min window 56
Window Sum 478, worse bit 10, min window 58
NOTICE:  EMI: Detected DRAM size: 256MB
NOTICE:  EMI: complex R/W mem test passed
NOTICE:  CPU: MT7981 (1300MHz)
NOTICE:  SPI_NAND parses attributes from parameter page.
NOTICE:  SPI_NAND Detected ID 0xc8
NOTICE:  Page size 2048, Block size 131072, size 134217728
NOTICE:  Initializing NMBM ...
NOTICE:  Signature found at block 1023 [0x07fe0000]
NOTICE:  First info table with writecount 0 found in block 960
NOTICE:  Second info table with writecount 0 found in block 963
NOTICE:  NMBM has been successfully attached in read-only mode
NOTICE:  BL2: Booting BL31
NOTICE:  BL31: v2.6(release):e233a3d581-dirty
NOTICE:  BL31: Built : 06:23:27, Jul 30 2023
NOTICE:  Hello BL31!!!
In:    serial@11002000
Out:   serial@11002000
Err:   serial@11002000
Net:   eth0: ethernet@15100000

  *** U-Boot Boot Menu ***

     1. Startup system (Default)
     2. Startup firmware0
     3. Startup firmware1
     4. Upgrade firmware
     5. Upgrade ATF BL2
     6. Upgrade ATF FIP
     7. Upgrade single image
     8. Load image
     0. U-Boot console


  Press UP/DOWN to move, ENTER to select, ESC/CTRL+C to quit
detect button reset released!
Reading from 0x0 to 0x4f7fdd7c, size 0x4 ... OK
Boot failure detected on both systems
Reading from 0x0 to 0x4f7fdd7c, size 0x4 ... OK
Saving Environment to MTD... Erasing on MTD device 'nmbm0'... OK
Writing to MTD device 'nmbm0'... OK
OK
Booting System 0, sys1_failed = 67, sys2_failed = 8
ubi0: attaching mtd9
ubi0: scanning is finished
ubi0: attached mtd9 (name "ubi", size 34 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 272, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 0, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 3/2, WL threshold: 4096, image sequence number: 1503784899
ubi0: available PEBs: 249, total reserved PEBs: 23, PEBs reserved for bad PEB handling: 19
Reading from volume 'kernel' to 0x46000000, size 0x0 ... *** Cannot find volume 'kernel' ***
resetting ...

F0: 102B 0000
FA: 1040 0000
FA: 1040 0000 [0200]
F9: 0000 0000
V0: 0000 0000 [0001]
00: 0000 0000
BP: 2400 0041 [0000]
G0: 1190 0000
EC: 0000 0000 [1000]
T0: 0000 024F [010F]
Jump to BL

NOTICE:  BL2: v2.6(release):e233a3d581-dirty
NOTICE:  BL2: Built : 06:23:27, Jul 30 2023
NOTICE:  WDT: disabled
NOTICE:  EMI: Using DDR3 settings

dump toprgu registers data:
1001c000 | 00000000 0000ffe0 00000000 00000000
1001c010 | 00000fff 00000000 00f00000 00000000
1001c020 | 00000000 00000000 00000000 00000000
1001c030 | 003c0003 003c0003 00000000 00000000
1001c040 | 00000000 00000000 00000000 00000000
1001c050 | 00000000 00000000 00000000 00000000
1001c060 | 00000000 00000000 00000000 00000000
1001c070 | 00000000 00000000 00000000 00000000
1001c080 | 00000000 00000000 00000000 00000000

dump drm registers data:
1001d000 | 00000000 00000000 00000000 00000000
1001d010 | 00000000 00000000 00000000 00000000
1001d020 | 00000000 00000000 00000000 00000000
1001d030 | 00a003f1 000000ff 00100000 00000000
1001d040 | 00027e71 000200a0 00020303 000000ff
1001d050 | 00000000 00000000 00000000 00000000
1001d060 | 00000002 00000000 00000000 00000000
drm: 500 = 0xc
[DDR Reserve] ddr reserve mode not be enabled yet
DDR RESERVE Success 0
[EMI] ComboMCP not ready, using default setting
BYTE_swap:0
BYTE_swap:0
Window Sum 632, worse bit 0, min window 76
Window Sum 616, worse bit 8, min window 76
Window Sum 528, worse bit 0, min window 64
Window Sum 472, worse bit 11, min window 56
Window Sum 530, worse bit 4, min window 64
Window Sum 480, worse bit 10, min window 58
Window Sum 484, worse bit 10, min window 58
Window Sum 486, worse bit 8, min window 60
NOTICE:  EMI: Detected DRAM size: 256MB
NOTICE:  EMI: complex R/W mem test passed
NOTICE:  CPU: MT7981 (1300MHz)
NOTICE:  SPI_NAND parses attributes from parameter page.
NOTICE:  SPI_NAND Detected ID 0xc8
NOTICE:  Page size 2048, Block size 131072, size 134217728
NOTICE:  Initializing NMBM ...
NOTICE:  Signature found at block 1023 [0x07fe0000]
NOTICE:  First info table with writecount 0 found in block 960
NOTICE:  Second info table with writecount 0 found in block 963
NOTICE:  NMBM has been successfully attached in read-only mode
NOTICE:  BL2: Booting BL31
NOTICE:  BL31: v2.6(release):e233a3d581-dirty
NOTICE:  BL31: Built : 06:23:27, Jul 30 2023
NOTICE:  Hello BL31!!!
In:    serial@11002000
Out:   serial@11002000
Err:   serial@11002000
Net:   ▒▒▒▒p
F0: 102B 0000
FA: 1040 0000
FA: 1040 0000 [0200]
F9: 0000 0000
V0: 0000 0000 [0001]
00: 0000 0000
BP: 2400 0041 [0000]
G0: 1190 0000
EC: 0000 0000 [1000]
T0: 0000 024F [010F]
Jump to BL

NOTICE:  BL2: v2.6(release):e233a3d581-dirty
NOTICE:  BL2: Built : 06:23:27, Jul 30 2023
NOTICE:  WDT: disabled
NOTICE:  EMI: Using DDR3 settings

dump toprgu registers data:
1001c000 | 00000000 0000ffe0 00000000 00000000
1001c010 | 00000fff 00000000 00f00000 00000000
1001c020 | 00000000 00000000 00000000 00000000
1001c030 | 003c0003 003c0003 00000000 00000000
1001c040 | 00000000 00000000 00000000 00000000
1001c050 | 00000000 00000000 00000000 00000000
1001c060 | 00000000 00000000 00000000 00000000
1001c070 | 00000000 00000000 00000000 00000000
1001c080 | 00000000 00000000 00000000 00000000

dump drm registers data:
1001d000 | 00000000 00000000 00000000 00000000
1001d010 | 00000000 00000000 00000000 00000000
1001d020 | 00000000 00000000 00000000 00000000
1001d030 | 00a083f1 000003ff 00100000 00000000
1001d040 | 00000000 00000000 00020303 000000ff
1001d050 | 00000000 00000000 00000000 00000000
1001d060 | 00000002 00000000 00000000 00000000
drm: 500 = 0x8
[DDR Reserve] ddr reserve mode not be enabled yet
DDR RESERVE Success 0
[EMI] ComboMCP not ready, using default setting
BYTE_swap:0
BYTE_swap:0
Window Sum 640, worse bit 0, min window 80
Window Sum 616, worse bit 11, min window 72
Window Sum 522, worse bit 0, min window 64
Window Sum 456, worse bit 10, min window 54
Window Sum 462, worse bit 8, min window 56
Window Sum 470, worse bit 11, min window 56
Window Sum 476, worse bit 11, min window 56
NOTICE:  EMI: Detected DRAM size: 256MB
NOTICE:  EMI: complex R/W mem test passed
NOTICE:  CPU: MT7981 (1300MHz)
NOTICE:  SPI_NAND parses attributes from parameter page.
NOTICE:  SPI_NAND Detected ID 0xc8
NOTICE:  Page size 2048, Block size 131072, size 134217728
NOTICE:  Initializing NMBM ...
NOTICE:  Signature found at block 1023 [0x07fe0000]
NOTICE:  First info table with writecount 0 found in block 960
NOTICE:  Second info table with writecount 0 found in block 963
NOTICE:  NMBM has been successfully attached in read-only mode
NOTICE:  BL2: Booting BL31
NOTICE:  BL31: v2.6(release):e233a3d581-dirty
NOTICE:  BL31: Built : 06:23:27, Jul 30 2023
NOTICE:  Hello BL31!!!
In:    serial@11002000
Out:   serial@11002000
Err:   serial@11002000
Net:   eth0: ethernet@15100000

  *** U-Boot Boot Menu ***

     1. Startup system (Default)
     2. Startup firmware0
     3. Startup firmware1
     4. Upgrade firmware
     5. Upgrade ATF BL2
     6. Upgrade ATF FIP
     7. Upgrade single image
     8. Load image
     0. U-Boot console


  Press UP/DOWN to move, ENTER to select, ESC/CTRL+C to quit
 detect button reset pressed, continue check 5 secs
 detect button reset pressed 5 secs !
 confirm to launch xq_upgrade !
 cmd=dhcp
BOOTP broadcast 1
BOOTP broadcast 2
BOOTP broadcast 3
BOOTP broadcast 4
BOOTP broadcast 5
BOOTP broadcast 6
BOOTP broadcast 7
BOOTP broadcast 8
BOOTP broadcast 9
BOOTP broadcast 10
BOOTP broadcast 11
BOOTP broadcast 12
BOOTP broadcast 13
BOOTP broadcast 14
BOOTP broadcast 15

Abort
======== dhcp failed, retry !========
 confirm to launch xq_upgrade !
 cmd=dhcp
BOOTP broadcast 1
BOOTP broadcast 2
BOOTP broadcast 3
BOOTP broadcast 4
BOOTP broadcast 5

Abort
======== dhcp failed, retry !========
 confirm to launch xq_upgrade !
 cmd=dhcp
BOOTP broadcast 1

Abort
======== dhcp failed, retry !========
 confirm to launch xq_upgrade !
 cmd=dhcp
BOOTP broadcast 1
BOOTP broadcast 2
BOOTP broadcast 3
BOOTP broadcast 4
BOOTP broadcast 5
BOOTP broadcast 6
eth0: ethernet@15100000
[b]
  *** U-Boot Boot Menu ***

     1. Startup system (Default)
     2. Startup firmware0
     3. Startup firmware1
     4. Upgrade firmware
     5. Upgrade ATF BL2
     6. Upgrade ATF FIP
     7. Upgrade single image
     8. Load image
     0. U-Boot console


  Press UP/DOWN to move, ENTER to select, ESC/CTRL+C to quit

*** Upgrading Single image ***

Available load methods:

  *** U-Boot Boot Menu ***

     1. Startup system (Default)
     2. Startup firmware0
     3. Startup firmware1
     4. Upgrade firmware
     5. Upgrade ATF BL2lt): 1
     6. Upgrade ATF FIP
     7. Upgrade single imageting ***
     8. Load image
     0. U-Boot console
*** Loaded 0 (0x0) bytes at 0x46000000 ***

  Press UP/DOWN to move, ENTER to select, ESC/CTRL+C to quit

Hit any key to stop autoboot:  0
RD03> <INTERRUPT>
RD03> <INTERRUPT>
RD03> <INTERRUPT>
RD03> <INTERRUPT>
RD03>
RD03>  ` 00 s                                                                 1

*** Upgrading Firmware ***

Run image after upgrading? (Y/n): y

Available load methods:
    0 - TFTP client (Default)
    1 - Xmodem
    2 - Ymodem
    3 - Kermit
    4 - S-Record
    5 - RAM

Select (enter for default): 0

Input U-Boot's IP address: 192.168.10.1
Input TFTP server's IP address: 192.168.10.100
*** Operation Aborted! ***
Hit any key to stop autoboot:  0
RD03> y <INTERRUPT>
RD03> <INTERRUPT>
RD03> ▒▒▒▒▒
F0: 102B 0000
FA: 1040 0000
FA: 1040 0000 [0200]
F9: 0000 0000
V0: 0000 0000 [0001]
00: 0000 0000
BP: 2400 0041 [0000]
G0: 1190 0000
EC: 0000 0000 [1000]
T0: 0000 024F [010F]
Jump to BL

NOTICE:  BL2: v2.6(release):e233a3d581-dirty
NOTICE:  BL2: Built : 06:23:27, Jul 30 2023
NOTICE:  WDT: disabled
NOTICE:  EMI: Using DDR3 settings

dump toprgu registers data:
1001c000 | 00000000 0000ffe0 00000000 00000000
1001c010 | 00000fff 00000000 00f00000 00000000
1001c020 | 00000000 00000000 00000000 00000000
1001c030 | 003c0003 003c0003 00000000 00000000
1001c040 | 00000000 00000000 00000000 00000000
1001c050 | 00000000 00000000 00000000 00000000
1001c060 | 00000000 00000000 00000000 00000000
1001c070 | 00000000 00000000 00000000 00000000
1001c080 | 00000000 00000000 00000000 00000000

dump drm registers data:
1001d000 | 00000000 00000000 00000000 00000000
1001d010 | 00000000 00000000 00000000 00000000
1001d020 | 00000000 00000000 00000000 00000000
1001d030 | 00a083f1 000003ff 00100000 00000000
1001d040 | 00000000 00000000 00020303 000000ff
1001d050 | 00000000 00000000 00000000 00000000
1001d060 | 00000002 00000000 00000000 00000000
drm: 500 = 0x8
[DDR Reserve] ddr reserve mode not be enabled yet
DDR RESERVE Success 0
[EMI] ComboMCP not ready, using default setting
BYTE_swap:0
BYTE_swap:0
Window Sum 636, worse bit 0, min window 76
Window Sum 612, worse bit 11, min window 72
Window Sum 524, worse bit 1, min window 64
Window Sum 474, worse bit 15, min window 56
Window Sum 476, worse bit 11, min window 56
Window Sum 484, worse bit 8, min window 60
Window Sum 488, worse bit 8, min window 60
NOTICE:  EMI: Detected DRAM size: 256MB
NOTICE:  EMI: complex R/W mem test passed
NOTICE:  CPU: MT7981 (1300MHz)
NOTICE:  SPI_NAND parses attributes from parameter page.
NOTICE:  SPI_NAND Detected ID 0xc8
NOTICE:  Page size 2048, Block size 131072, size 134217728
NOTICE:  Initializing NMBM ...
NOTICE:  Signature found at block 1023 [0x07fe0000]
NOTICE:  First info table with writecount 0 found in block 960
NOTICE:  Second info table with writecount 0 found in block 963
NOTICE:  NMBM has been successfully attached in read-only mode
NOTICE:  BL2: Booting BL31
NOTICE:  BL31: v2.6(release):e233a3d581-dirty
NOTICE:  BL31: Built : 06:23:27, Jul 30 2023
NOTICE:  Hello BL31!!!
In:    serial@11002000
Out:   serial@11002000
Err:   serial@11002000
Net:   eth0: ethernet@15100000

  *** U-Boot Boot Menu ***

     1. Startup system (Default)
     2. Startup firmware0
     3. Startup firmware1
     4. Upgrade firmware
     5. Upgrade ATF BL2
     6. Upgrade ATF FIP
     7. Upgrade single image
     8. Load image
     0. U-Boot console


  Press UP/DOWN to move, ENTER to select, ESC/CTRL+C to quit
detect button reset released!
Reading from 0x0 to 0x4f7fdd7c, size 0x4 ... OK
Boot failure detected on both systems
Reading from 0x0 to 0x4f7fdd7c, size 0x4 ... OK
Saving Environment to MTD... Erasing on MTD device 'nmbm0'... OK
Writing to MTD device 'nmbm0'... OK
OK
Booting System 0, sys1_failed = 68, sys2_failed = 8
ubi0: attaching mtd9
ubi0: scanning is finished
ubi0: attached mtd9 (name "ubi", size 34 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 272, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 0, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 3/2, WL threshold: 4096, image sequence number: 1503784899
ubi0: available PEBs: 249, total reserved PEBs: 23, PEBs reserved for bad PEB handling: 19
Reading from volume 'kernel' to 0x46000000, size 0x0 ... *** Cannot find volume 'kernel' ***
resetting ...

F0: 102B 0000
FA: 1040 0000
FA: 1040 0000 [0200]
F9: 0000 0000
V0: 0000 0000 [0001]
00: 0000 0000
BP: 2400 0041 [0000]
G0: 1190 0000
EC: 0000 0000 [1000]
T0: 0000 024F [010F]
Jump to BL

NOTICE:  BL2: v2.6(release):e233a3d581-dirty
NOTICE:  BL2: Built : 06:23:27, Jul 30 2023
NOTICE:  WDT: disabled
NOTICE:  EMI: Using DDR3 settings

dump toprgu registers data:
1001c000 | 00000000 0000ffe0 00000000 00000000
1001c010 | 00000fff 00000000 00f00000 00000000
1001c020 | 00000000 00000000 00000000 00000000
1001c030 | 003c0003 003c0003 00000000 00000000
1001c040 | 00000000 00000000 00000000 00000000
1001c050 | 00000000 00000000 00000000 00000000
1001c060 | 00000000 00000000 00000000 00000000
1001c070 | 00000000 00000000 00000000 00000000
1001c080 | 00000000 00000000 00000000 00000000

dump drm registers data:
1001d000 | 00000000 00000000 00000000 00000000
1001d010 | 00000000 00000000 00000000 00000000
1001d020 | 00000000 00000000 00000000 00000000
1001d030 | 00a003f1 000000ff 00100000 00000000
1001d040 | 00027e71 000200a0 00020303 000000ff
1001d050 | 00000000 00000000 00000000 00000000
1001d060 | 00000002 00000000 00000000 00000000
drm: 500 = 0xc
[DDR Reserve] ddr reserve mode not be enabled yet
DDR RESERVE Success 0
[EMI] ComboMCP not ready, using default setting
BYTE_swap:0
BYTE_swap:0
Window Sum 632, worse bit 0, min window 76
Window Sum 600, worse bit 9, min window 72
Window Sum 524, worse bit 1, min window 64
Window Sum 454, worse bit 10, min window 54
Window Sum 468, worse bit 10, min window 56
Window Sum 472, worse bit 11, min window 56
Window Sum 478, worse bit 10, min window 58
NOTICE:  EMI: Detected DRAM size: 256MB
NOTICE:  EMI: complex R/W mem test passed
NOTICE:  CPU: MT7981 (1300MHz)
NOTICE:  SPI_NAND parses attributes from parameter page.
NOTICE:  SPI_NAND Detected ID 0xc8
NOTICE:  Page size 2048, Block size 131072, size 134217728
NOTICE:  Initializing NMBM ...
NOTICE:  Signature found at block 1023 [0x07fe0000]
NOTICE:  First info table with writecount 0 found in block 960
NOTICE:  Second info table with writecount 0 found in block 963
NOTICE:  NMBM has been successfully attached in read-only mode
NOTICE:  BL2: Booting BL31
NOTICE:  BL31: v2.6(release):e233a3d581-dirty
NOTICE:  BL31: Built : 06:23:27, Jul 30 2023
NOTICE:  Hello BL31!!!
In:    serial@11002000
Out:   serial@11002000
Err:   serial@11002000
Net:   eth0: ethernet@15100000

  *** U-Boot Boot Menu ***

     1. Startup system (Default)
     2. Startup firmware0
     3. Startup firmware1
     4. Upgrade firmware
     5. Upgrade ATF BL2
     6. Upgrade ATF FIP
     7. Upgrade single image
     8. Load image
     0. U-Boot console


  Press UP/DOWN to move, ENTER to select, ESC/CTRL+C to quit

*** Upgrading Firmware ***

Run image after upgrading? (Y/n): y

Available load methods:
    0 - TFTP client (Default)
    1 - Xmodem
    2 - Ymodem
    3 - Kermit
    4 - S-Record
    5 - RAM

Select (enter for default): 0

Input U-Boot's IP address: 192.168.10.1
Input TFTP server's IP address: 192.168.10.100
Input IP netmask: 255.255.255.0
Input file name: C0A81F02.img

Using ethernet@15100000 device
TFTP from server 192.168.10.100; our IP address is 192.168.10.1
Filename 'C0A81F02.img'.
Load address: 0x46000000
Loading: #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         ################################################
         6.6 MiB/s
done
Bytes transferred = 23593992 (1680408 hex)
Saving Environment to MTD... Erasing on MTD device 'nmbm0'... OK
Writing to MTD device 'nmbm0'... OK
OK

*** Loaded 23593992 (0x1680408) bytes at 0x46000000 ***

*** Image not supported! ***
Hit any key to stop autoboot:  0
detect button reset released!
Reading from 0x0 to 0x4f7ff2cc, size 0x4 ... OK
Boot failure detected on both systems
Reading from 0x0 to 0x4f7ff2cc, size 0x4 ... OK
Saving Environment to MTD... Erasing on MTD device 'nmbm0'... OK
Writing to MTD device 'nmbm0'... OK
OK
Booting System 0, sys1_failed = 69, sys2_failed = 8
ubi0: attaching mtd9
ubi0: scanning is finished
ubi0: attached mtd9 (name "ubi", size 34 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 272, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 0, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 3/2, WL threshold: 4096, image sequence number: 1503784899
ubi0: available PEBs: 249, total reserved PEBs: 23, PEBs reserved for bad PEB handling: 19
Reading from volume 'kernel' to 0x46000000, size 0x0 ... *** Cannot find volume 'kernel' ***
resetting ...

F0: 102B 0000
FA: 1040 0000
FA: 1040 0000 [0200]
F9: 0000 0000
V0: 0000 0000 [0001]
00: 0000 0000
BP: 2400 0041 [0000]
G0: 1190 0000
EC: 0000 0000 [1000]
T0: 0000 024F [010F]
Jump to BL

NOTICE:  BL2: v2.6(release):e233a3d581-dirty
NOTICE:  BL2: Built : 06:23:27, Jul 30 2023
NOTICE:  WDT: disabled
NOTICE:  EMI: Using DDR3 settings

dump toprgu registers data:
1001c000 | 00000000 0000ffe0 00000000 00000000
1001c010 | 00000fff 00000000 00f00000 00000000
1001c020 | 00000000 00000000 00000000 00000000
1001c030 | 003c0003 003c0003 00000000 00000000
1001c040 | 00000000 00000000 00000000 00000000
1001c050 | 00000000 00000000 00000000 00000000
1001c060 | 00000000 00000000 00000000 00000000
1001c070 | 00000000 00000000 00000000 00000000
1001c080 | 00000000 00000000 00000000 00000000

dump drm registers data:
1001d000 | 00000000 00000000 00000000 00000000
1001d010 | 00000000 00000000 00000000 00000000
1001d020 | 00000000 00000000 00000000 00000000
1001d030 | 00a003f1 000000ff 00100000 00000000
1001d040 | 00027e71 000200a0 00020303 000000ff
1001d050 | 00000000 00000000 00000000 00000000
1001d060 | 00000002 00000000 00000000 00000000
drm: 500 = 0xc
[DDR Reserve] ddr reserve mode not be enabled yet
DDR RESERVE Success 0
[EMI] ComboMCP not ready, using default setting
BYTE_swap:0
BYTE_swap:0
Window Sum 620, worse bit 0, min window 76
Window Sum 620, worse bit 8, min window 76
Window Sum 526, worse bit 4, min window 64
Window Sum 470, worse bit 11, min window 56
Window Sum 486, worse bit 10, min window 58
Window Sum 490, worse bit 10, min window 58
Window Sum 528, worse bit 1, min window 64
Window Sum 492, worse bit 8, min window 60
NOTICE:  EMI: Detected DRAM size: 256MB
NOTICE:  EMI: complex R/W mem test passed
NOTICE:  CPU: MT7981 (1300MHz)
NOTICE:  SPI_NAND parses attributes from parameter page.
NOTICE:  SPI_NAND Detected ID 0xc8
NOTICE:  Page size 2048, Block size 131072, size 134217728
NOTICE:  Initializing NMBM ...
NOTICE:  Signature found at block 1023 [0x07fe0000]
NOTICE:  First info table with writecount 0 found in block 960
NOTICE:  Second info table with writecount 0 found in block 963
NOTICE:  NMBM has been successfully attached in read-only mode
NOTICE:  BL2: Booting BL31
NOTICE:  BL31: v2.6(release):e233a3d581-dirty
NOTICE:  BL31: Built : 06:23:27, Jul 30 2023
NOTICE:  Hello BL31!!!
In:    serial@11002000
Out:   serial@11002000
Err:   serial@11002000
Net:   eth0: ethernet@15100000

  *** U-Boot Boot Menu ***

     1. Startup system (Default)
     2. Startup firmware0
     3. Startup firmware1
     4. Upgrade firmware
     5. Upgrade ATF BL2
     6. Upgrade ATF FIP
     7. Upgrade single image
     8. Load image
     0. U-Boot console


  Press UP/DOWN to move, ENTER to select, ESC/CTRL+C to quit

*** Upgrading Firmware ***

Run image after upgrading? (Y/n): y

Available load methods:
    0 - TFTP client (Default)
    1 - Xmodem
    2 - Ymodem
    3 - Kermit
    4 - S-Record
    5 - RAM

Select (enter for default): 0

Input U-Boot's IP address: 192.168.10.1
Input TFTP server's IP address: 192.168.10.100
Input IP netmask: 255.255.255.0
Input file name: C0A81F02.img

Using ethernet@15100000 device
TFTP from server 192.168.10.100; our IP address is 192.168.10.1
Filename 'C0A81F02.img'.
Load address: 0x46000000
Loading: #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         ################################################
         6.6 MiB/s
done
Bytes transferred = 23593992 (1680408 hex)
Saving Environment to MTD... Erasing on MTD device 'nmbm0'... OK
Writing to MTD device 'nmbm0'... OK
OK

*** Loaded 23593992 (0x1680408) bytes at 0x46000000 ***

*** Image not supported! ***
Hit any key to stop autoboot:  0
detect button reset released!
Reading from 0x0 to 0x4f7ff2cc, size 0x4 ... OK
Boot failure detected on both systems
Reading from 0x0 to 0x4f7ff2cc, size 0x4 ... OK
Saving Environment to MTD... Erasing on MTD device 'nmbm0'... OK
Writing to MTD device 'nmbm0'... OK
OK
Booting System 0, sys1_failed = 70, sys2_failed = 8
ubi0: attaching mtd9
ubi0: scanning is finished
ubi0: attached mtd9 (name "ubi", size 34 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 272, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 0, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 3/2, WL threshold: 4096, image sequence number: 1503784899
ubi0: available PEBs: 249, total reserved PEBs: 23, PEBs reserved for bad PEB handling: 19
Reading from volume 'kernel' to 0x46000000, size 0x0 ... *** Cannot find volume 'kernel' ***
resetting ...

F0: 102B 0000
FA: 1040 0000
FA: 1040 0000 [0200]
F9: 0000 0000
V0: 0000 0000 [0001]
00: 0000 0000
BP: 2400 0041 [0000]
G0: 1190 0000
EC: 0000 0000 [1000]
T0: 0000 024F [010F]
Jump to BL

NOTICE:  BL2: v2.6(release):e233a3d581-dirty
NOTICE:  BL2: Built : 06:23:27, Jul 30 2023
NOTICE:  WDT: disabled
NOTICE:  EMI: Using DDR3 settings

dump toprgu registers data:
1001c000 | 00000000 0000ffe0 00000000 00000000
1001c010 | 00000fff 00000000 00f00000 00000000
1001c020 | 00000000 00000000 00000000 00000000
1001c030 | 003c0003 003c0003 00000000 00000000
1001c040 | 00000000 00000000 00000000 00000000
1001c050 | 00000000 00000000 00000000 00000000
1001c060 | 00000000 00000000 00000000 00000000
1001c070 | 00000000 00000000 00000000 00000000
1001c080 | 00000000 00000000 00000000 00000000

dump drm registers data:
1001d000 | 00000000 00000000 00000000 00000000
1001d010 | 00000000 00000000 00000000 00000000
1001d020 | 00000000 00000000 00000000 00000000
1001d030 | 00a003f1 000000ff 00100000 00000000
1001d040 | 00027e71 000200a0 00020303 000000ff
1001d050 | 00000000 00000000 00000000 00000000
1001d060 | 00000002 00000000 00000000 00000000
drm: 500 = 0xc
[DDR Reserve] ddr reserve mode not be enabled yet
DDR RESERVE Success 0
[EMI] ComboMCP not ready, using default setting
BYTE_swap:0
BYTE_swap:0
Window Sum 628, worse bit 0, min window 76
Window Sum 616, worse bit 11, min window 72
Window Sum 532, worse bit 0, min window 66
Window Sum 466, worse bit 8, min window 56
Window Sum 484, worse bit 10, min window 58
Window Sum 490, worse bit 8, min window 60
NOTICE:  EMI: Detected DRAM size: 256MB
NOTICE:  EMI: complex R/W mem test passed
NOTICE:  CPU: MT7981 (1300MHz)
NOTICE:  SPI_NAND parses attributes from parameter page.
NOTICE:  SPI_NAND Detected ID 0xc8
NOTICE:  Page size 2048, Block size 131072, size 134217728
NOTICE:  Initializing NMBM ...
NOTICE:  Signature found at block 1023 [0x07fe0000]
NOTICE:  First info table with writecount 0 found in block 960
NOTICE:  Second info table with writecount 0 found in block 963
NOTICE:  NMBM has been successfully attached in read-only mode
NOTICE:  BL2: Booting BL31
NOTICE:  BL31: v2.6(release):e233a3d581-dirty
NOTICE:  BL31: Built : 06:23:27, Jul 30 2023
NOTICE:  Hello BL31!!!
In:    serial@11002000
Out:   serial@11002000
Err:   serial@11002000
Net:   eth0: ethernet@15100000

  *** U-Boot Boot Menu ***

     1. Startup system (Default)
     2. Startup firmware0
     3. Startup firmware1
     4. Upgrade firmware
     5. Upgrade ATF BL2
     6. Upgrade ATF FIP
     7. Upgrade single image
     8. Load image
     0. U-Boot console


  Press UP/DOWN to move, ENTER to select, ESC/CTRL+C to quit

*** Upgrading Firmware ***

Run image after upgrading? (Y/n): y

Available load methods:
    0 - TFTP client (Default)
    1 - Xmodem
    2 - Ymodem
    3 - Kermit
    4 - S-Record
    5 - RAM

Select (enter for default): 0

Input U-Boot's IP address: 192.168.10.1
Input TFTP server's IP address: 192.168.10.100
Input IP netmask: 255.255.255.0
Input file name: C0A81F02.img

Using ethernet@15100000 device
TFTP from server 192.168.10.100; our IP address is 192.168.10.1
Filename 'C0A81F02.img'.
Load address: 0x46000000
Loading: #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         ################################################
         6.6 MiB/s
done
Bytes transferred = 23593992 (1680408 hex)
Saving Environment to MTD... Erasing on MTD device 'nmbm0'... OK
Writing to MTD device 'nmbm0'... OK
OK

*** Loaded 23593992 (0x1680408) bytes at 0x46000000 ***

*** Image not supported! ***
Hit any key to stop autoboot:  0
detect button reset released!
Reading from 0x0 to 0x4f7ff2cc, size 0x4 ... OK
Boot failure detected on both systems
Reading from 0x0 to 0x4f7ff2cc, size 0x4 ... OK
Saving Environment to MTD... Erasing on MTD device 'nmbm0'... OK
Writing to MTD device 'nmbm0'... OK
OK
Booting System 0, sys1_failed = 71, sys2_failed = 8
ubi0: attaching mtd9
ubi0: scanning is finished
ubi0: attached mtd9 (name "ubi", size 34 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 272, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 0, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 3/2, WL threshold: 4096, image sequence number: 1503784899
ubi0: available PEBs: 249, total reserved PEBs: 23, PEBs reserved for bad PEB handling: 19
Reading from volume 'kernel' to 0x46000000, size 0x0 ... *** Cannot find volume 'kernel' ***
resetting ...

F0: 102B 0000
FA: 1040 0000
FA: 1040 0000 [0200]
F9: 0000 0000
V0: 0000 0000 [0001]
00: 0000 0000
BP: 2400 0041 [0000]
G0: 1190 0000
EC: 0000 0000 [1000]
T0: 0000 024F [010F]
Jump to BL

NOTICE:  BL2: v2.6(release):e233a3d581-dirty
NOTICE:  BL2: Built : 06:23:27, Jul 30 2023
NOTICE:  WDT: disabled
NOTICE:  EMI: Using DDR3 settings

dump toprgu registers data:
1001c000 | 00000000 0000ffe0 00000000 00000000
1001c010 | 00000fff 00000000 00f00000 00000000
1001c020 | 00000000 00000000 00000000 00000000
1001c030 | 003c0003 003c0003 00000000 00000000
1001c040 | 00000000 00000000 00000000 00000000
1001c050 | 00000000 00000000 00000000 00000000
1001c060 | 00000000 00000000 00000000 00000000
1001c070 | 00000000 00000000 00000000 00000000
1001c080 | 00000000 00000000 00000000 00000000

dump drm registers data:
1001d000 | 00000000 00000000 00000000 00000000
1001d010 | 00000000 00000000 00000000 00000000
1001d020 | 00000000 00000000 00000000 00000000
1001d030 | 00a003f1 000000ff 00100000 00000000
1001d040 | 00027e71 000200a0 00020303 000000ff
1001d050 | 00000000 00000000 00000000 00000000
1001d060 | 00000002 00000000 00000000 00000000
drm: 500 = 0xc
[DDR Reserve] ddr reserve mode not be enabled yet
DDR RESERVE Success 0
[EMI] ComboMCP not ready, using default setting
BYTE_swap:0
BYTE_swap:0
Window Sum 632, worse bit 0, min window 76
Window Sum 600, worse bit 11, min window 72
Window Sum 518, worse bit 0, min window 64
Window Sum 458, worse bit 15, min window 54
Window Sum 524, worse bit 1, min window 64
Window Sum 464, worse bit 8, min window 56
Window Sum 468, worse bit 10, min window 56
Window Sum 476, worse bit 8, min window 58
NOTICE:  EMI: Detected DRAM size: 256MB
NOTICE:  EMI: complex R/W mem test passed
NOTICE:  CPU: MT7981 (1300MHz)
NOTICE:  SPI_NAND parses attributes from parameter page.
NOTICE:  SPI_NAND Detected ID 0xc8
NOTICE:  Page size 2048, Block size 131072, size 134217728
NOTICE:  Initializing NMBM ...
NOTICE:  Signature found at block 1023 [0x07fe0000]
NOTICE:  First info table with writecount 0 found in block 960
NOTICE:  Second info table with writecount 0 found in block 963
NOTICE:  NMBM has been successfully attached in read-only mode
NOTICE:  BL2: Booting BL31
NOTICE:  BL31: v2.6(release):e233a3d581-dirty
NOTICE:  BL31: Built : 06:23:27, Jul 30 2023
NOTICE:  Hello BL31!!!
In:    serial@11002000
Out:   serial@11002000
Err:   serial@11002000
Net:   eth0: ethernet@15100000

  *** U-Boot Boot Menu ***

     1. Startup system (Default)
     2. Startup firmware0
     3. Startup firmware1
     4. Upgrade firmware
     5. Upgrade ATF BL2
     6. Upgrade ATF FIP
     7. Upgrade single image
     8. Load image
     0. U-Boot console


  Press UP/DOWN to move, ENTER to select, ESC/CTRL+C to quit

*** Upgrading Single image ***

Available load methods:
    0 - TFTP client (Default)
    1 - Xmodem
    2 - Ymodem
    3 - Kermit
    4 - S-Record
    5 - RAM

Select (enter for default): 0

Input U-Boot's IP address: 192.168.10.1
Input TFTP server's IP address: 192.168.10.100
Input IP netmask: 255.255.255.0
Input file name: C0A81F02.img

Using ethernet@15100000 device
TFTP from server 192.168.10.100; our IP address is 192.168.10.1
Filename 'C0A81F02.img'.
Load address: 0x46000000
Loading: #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         ################################################
         6.6 MiB/s
done
Bytes transferred = 23593992 (1680408 hex)
Saving Environment to MTD... Erasing on MTD device 'nmbm0'... OK
Writing to MTD device 'nmbm0'... OK
OK

*** Loaded 23593992 (0x1680408) bytes at 0x46000000 ***

Erasing from 0x0 to 0x169ffff, size 0x16a0000 ... OK
Writing from 0x46000000 to 0x0, size 0x1680408 ... OK
Verifying from 0x0 to 0x1680407, size 0x1680408 ... OK

*** Single image upgrade completed! ***
Hit any key to stop autoboot:  0
detect button reset released!
Reading from 0x0 to 0x4f7ff2cc, size 0x4 ... OK
Boot failure detected on both systems
Reading from 0x0 to 0x4f7ff2cc, size 0x4 ... OK
Saving Environment to MTD... Erasing on MTD device 'nmbm0'... OK
Writing to MTD device 'nmbm0'... OK
OK
Booting System 0, sys1_failed = 72, sys2_failed = 8
ubi0: attaching mtd9
ubi0: scanning is finished
ubi0 error: ubi_read_volume_table: the layout volume was not found
ubi0 error: ubi_attach_mtd_dev: failed to attach mtd9, error -22
UBI error: cannot attach mtd9
UBI error: cannot initialize UBI, error -22
*** Failed to attach UBI ***
*** Rebuilding UBI ***
Erasing from 0x0 to 0x21fffff, size 0x2200000 ... OK
*** UBI is read-only mode ***
resetting ...

F0: 102B 0000
FA: 1040 0000
FA: 1040 0000 [0200]
F9: 3903 0041
F3: 1001 0000 [0200]
F3: 1001 0000
F6: 102C 0000
F5: 480A 0031
00: 1005 0000
FA: 1040 0000
FA: 1040 0000 [0200]
F9: 3903 0041
F3: 1001 0000 [0200]
F3: 1001 0000
F6: 102C 0000
01: 102A 0001
02: 1005 0000
BP: 2000 00C0 [0001]
EC: 0000 0000 [1000]
T0: 0000 00ED [010F]
System halt!


F0: 102B 0000
FA: 1040 0000
FA: 1040 0000 [0200]
F9: 3903 0041
F3: 1001 0000 [0200]
F3: 1001 0000
F6: 102C 0000
F5: 480A 0031
00: 1005 0000
FA: 1040 0000
FA: 1040 0000 [0200]
F9: 3903 0041
F3: 1001 0000 [0200]
F3: 1001 0000
F6: 102C 0000
01: 102A 0001
02: 1005 0000
BP: 2000 00C0 [0001]
EC: 0000 0000 [1000]
T0: 0000 00ED [010F]
System halt! [/b]

Probowałem wgrać soft (firmware) ale nie przyjmował, no to dawaj - update single image no i ubiłem router. Prawdopodobnie ubiłem uboot. Wgrywałem oczywiście obraz openwrt...
Sprawdziłem kość nand, nie mam czym jej odczytac, ch341 odpada. Szrot. Wiem, mogłem odpalić obraz z drugiej partycji, ale tak jak mówiłem pośpiech, brak czasu.

Zamówiłem drugi - już do mnie idzie.
Chciałbym tym razem nie ubić sprzętu przy zmienianiu oprogramowania i uboot.

Bazując oczywiście na https://openwrt.org/inbox/toh/xiaomi/ax3000t

Czy do pierwszego wgrania mogę użyć https://dl.eko.one.pl/luci/openwrt-23.0 … actory.ubi ?

Nastpępnie aby wgrać uboot wgrywam ten soft: https://dl.eko.one.pl/luci/openwrt-23.0 … actory.ubi ?
Jeśli chcę dodatkowe 10mega na recovery, wgrywam też plik https://dl.eko.one.pl/luci/openwrt-23.0 … covery.itb do tmp, a potem
ubimkvol /dev/ubi0 -n 2 -N recovery -s 10MiB
ubiupdatevol /dev/ubi0_2 /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-initramfs-recovery.itb
I dalej zgodnie z poradnikiem? Spokojnie mogę brać wszytskie pliki od Cezarego?
Pytania może i laickie, ale mając na uwadze, że ubiłem wcześniejszy egzemplarz - czytam i upewniam sie po 10 razy.

2 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 115,952

Odp: AX3000T - jak tego nie robic + upewnienie się by zrobić to dobrze

Pytanie - czemu nie widać było interfejsu bezprzewodowego?

Bo initramfs nie zawiera wszystkich sterowników, a w szczególności danych specyficznych dla danego modelu routera. Initramfs służy tylko przejściowo do wgrania docelowego softu i nie musi mieć wifi czy usb żeby się to dało zrobić. initramfs jest jeden, ogólny dla wszystkich buildów.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

3 Odpowiedź przez tygrysss

  • Zarejestrowany: 2015-06-19
  • Posty: 423

Odp: AX3000T - jak tego nie robic + upewnienie się by zrobić to dobrze

Ok dzięki za odpowiedz.
Co z reszta pytań - czy tych obrazów/plików mogę użyć?

4 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 115,952

Odp: AX3000T - jak tego nie robic + upewnienie się by zrobić to dobrze

W statystyce są AX3000T z moim softem, więc - komuś to działa.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

5 Odpowiedź przez MiG25 (edytowany przez MiG25 2024-08-03 15:13:58)

  • MiG25
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2014-07-23
  • Posty: 3,795

Odp: AX3000T - jak tego nie robic + upewnienie się by zrobić to dobrze

To na tym ubitym mtk_uartboot nie próbowałeś ?
Coś na ten wzór: https://eko.one.pl/forum/viewtopic.php? … 75#p302975

6 Odpowiedź przez tygrysss

  • Zarejestrowany: 2015-06-19
  • Posty: 423

Odp: AX3000T - jak tego nie robic + upewnienie się by zrobić to dobrze

MiG25 napisał/a:

To na tym ubitym mtk_uartboot nie próbowałeś ?
Coś na ten wzór: https://eko.one.pl/forum/viewtopic.php? … 75#p302975

Urządzenie stało się głuche, zero podświetlenia diody i nie nie wypluwalo na uart.

7 Odpowiedź przez tygrysss

  • Zarejestrowany: 2015-06-19
  • Posty: 423

Odp: AX3000T - jak tego nie robic + upewnienie się by zrobić to dobrze

Cezary napisał/a:

W statystyce są AX3000T z moim softem, więc - komuś to działa.

Ok - chodzi mi czy nie pomyliłem plików.

8 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 115,952

Odp: AX3000T - jak tego nie robic + upewnienie się by zrobić to dobrze

Wiesz że opisujesz jedno, a których plików faktycznie użyłeś i czy się nie pomyliłeś tego nikt nie wie.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

9 Odpowiedź przez MiG25

  • MiG25
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2014-07-23
  • Posty: 3,795

Odp: AX3000T - jak tego nie robic + upewnienie się by zrobić to dobrze

tygrysss napisał/a:
MiG25 napisał/a:

To na tym ubitym mtk_uartboot nie próbowałeś ?
Coś na ten wzór: https://eko.one.pl/forum/viewtopic.php? … 75#p302975

Urządzenie stało się głuche, zero podświetlenia diody i nie nie wypluwalo na uart.

No ale to ,że nic nie wypluwa na uart to nie znaczy , ze np ten program tej komunikacji nie zainicjuje i tego loadera przez uart nie wgra...

10 Odpowiedź przez tygrysss

  • Zarejestrowany: 2015-06-19
  • Posty: 423

Odp: AX3000T - jak tego nie robic + upewnienie się by zrobić to dobrze

MiG25 napisał/a:
tygrysss napisał/a:
MiG25 napisał/a:

To na tym ubitym mtk_uartboot nie próbowałeś ?
Coś na ten wzór: https://eko.one.pl/forum/viewtopic.php? … 75#p302975

Urządzenie stało się głuche, zero podświetlenia diody i nie nie wypluwalo na uart.

No ale to ,że nic nie wypluwa na uart to nie znaczy , ze np ten program tej komunikacji nie zainicjuje i tego loadera przez uart nie wgra...

Sprzęt został odesłany a dziś przyszedł nowy.
Pytanie jak pominąć te aktywacje? Nie chce go podłączać pod internet. Wcześniej jakoś gdzieś naklikalem i ustawiłem hasło wifi które było tez hasłem do panelu.

11 Odpowiedź przez MiG25

  • MiG25
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2014-07-23
  • Posty: 3,795

Odp: AX3000T - jak tego nie robic + upewnienie się by zrobić to dobrze

Jaka aktywacja? Chcesz zmienić na openwrt to robisz to wg instrukcji , i tylko niej.

12 Odpowiedź przez tygrysss

  • Zarejestrowany: 2015-06-19
  • Posty: 423

Odp: AX3000T - jak tego nie robic + upewnienie się by zrobić to dobrze

Pierwsze uruchomienie urządzenia z pudełka - sadzać po obrazkach chce dostęp do internetu.
Ok - naklikalem ustawiłem hasło i mam już dostęp do panelu oryginalnego softu.
Klucz (stock) wyciągnięty. Openwrt już na pokładzie.
Teraz próbuje zmienić uboot na ten openwrt.
Do tego z tego co widzę potrzebuje już internet - pobranie paczki kmod-mtd-rw
Zaczynam flashowac plikiem od Cezarego

13 Odpowiedź przez tygrysss

  • Zarejestrowany: 2015-06-19
  • Posty: 423

Odp: AX3000T - jak tego nie robic + upewnienie się by zrobić to dobrze

No to mamy sukces smile udało się wgrać uboot - urządzenie wstało.
Jest natomiast jedna nieścisłość. Plik Cezarego ubootmod-initramfs-recovery ma ponad 10 mega, podczas gdy partycja to 10 MiB.
Trzeba by może napisać aby zwiększyć partycje? Albo co?
Korzystałem w tym wypadku z oryginalnego pliki ze strony openwrt tak samo jak z bl2 i fip aby nie mieszać ich ze sobą.

14 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 115,952

Odp: AX3000T - jak tego nie robic + upewnienie się by zrobić to dobrze

Obraz z luci ubootmod-initramfs-recovery ma 7.8M
Obraz bez luci - 6.7M

Gdzie tam masz ponad 10M?

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

15 Odpowiedź przez tygrysss

  • Zarejestrowany: 2015-06-19
  • Posty: 423

Odp: AX3000T - jak tego nie robic + upewnienie się by zrobić to dobrze

Dostałem informacje ze jest za duży. Dlatego podmieniłem na ten z openwrt i poszło od Strzala.
Pytanie - gdzie podziala się sekcja „przełącznik” w zakładce siec? Chciałbym skonfigurować vlany etc jak w starym wdr4300

16 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 115,952

Odp: AX3000T - jak tego nie robic + upewnienie się by zrobić to dobrze

No to nie wiem co pobrałeś skoro oba są mniejsze niż 10M.

Nie ma od kilku wydań openwrt, urządzenie ma dsa a nie swconfig. Na portach normalnie zrób vlany.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

17 Odpowiedź przez mosquito

  • Zarejestrowany: 2017-12-15
  • Posty: 18

Odp: AX3000T - jak tego nie robic + upewnienie się by zrobić to dobrze

Cześć,
zainstalowałem openwrt na AX3000T zgodnie z instrukcją na:
https://www.androidpimp.com/wireless-ro … 0t-router/
https://openwrt.org/inbox/toh/xiaomi/ax3000t

Niestety zatrzymałem się na kroku
sysupgrade -n /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-squashfs-sysupgrade.bin

Mogę zalogować się do konsoli:
BusyBox v1.36.1 (2024-09-16 20:47:44 UTC) built-in shell (ash)

  _______                     ________        __
|       |.-----.-----.-----.|  |  |  |.----.|  |_
|   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
|_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
-----------------------------------------------------
OpenWrt SNAPSHOT, r27433-7e1d092552
-----------------------------------------------------
=== WARNING! =====================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.
--------------------------------------------------
root@OpenWrt:~#

po wykonaniu polecenia:
sysupgrade -n /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-squashfs-sysupgrade.bin

mam:
root@OpenWrt:/tmp# sysupgrade -n /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-squashfs-sysupgrade.bin
verifying sysupgrade tar file integrity
Mon Sep 16 20:57:08 UTC 2024 upgrade: Commencing upgrade. Closing all shell sessions.
Command failed: Connection failed
root@OpenWrt:/tmp# Connection to 192.168.1.1 closed by remote host.
Connection to 192.168.1.1 closed.
gc@gc-Vostro-3350:~$

pomożecie?

18 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 115,952

Odp: AX3000T - jak tego nie robic + upewnienie się by zrobić to dobrze

Wszystko jest ok, openwrt tak właśnie wypisuje robiąc aktualizację - zrywa sesję. Więc z czym masz problem?

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

19 Odpowiedź przez mosquito (edytowany przez mosquito 2024-10-06 19:56:45)

  • Zarejestrowany: 2017-12-15
  • Posty: 18

Odp: AX3000T - jak tego nie robic + upewnienie się by zrobić to dobrze

wybaczcie, jakaś pomroczność mnie ogarnęła