Nie jesteś zalogowany. Proszę się zalogować lub zarejestrować.
eko.one.pl → Sprzęt / Hardware → Router domowyz 5G
Strony Poprzednia 1 2 3 4
Zaloguj się lub zarejestruj by napisać odpowiedź
Niestety po wgraniu wersji luci*sysupgrade pacjent się nie odzywa.
Demontaż prosty, 4 śruby pod nóżkami i można się dostać do złącza uart.
Choć dla mnie podłączenie nie będzie proste.
Więc sprawdź co wypisuje na konsoli.
Tak się zatrzymuje:
Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.3.1-00163
S - IMAGE_VARIANT_STRING=HAACANAZA
S - OEM_IMAGE_VERSION_STRING=CRM
S - Boot Config, 0x000002e5
B - 201 - PBL, Start
B - 2735 - bootable_media_detect_entry, Start
B - 3447 - bootable_media_detect_success, Start
B - 3452 - elf_loader_entry, Start
B - 7623 - auth_hash_seg_entry, Start
B - 7868 - auth_hash_seg_exit, Start
B - 69641 - elf_segs_hash_verify_entry, Start
B - 132495 - PBL, End
B - 142526 - SBL1, Start
B - 194010 - GCC [RstStat:0x10, RstDbg:0x600000] WDog Stat : 0x4
B - 200446 - pm_device_init, Start
B - 319945 - PM_SET_VAL:Skip
D - 119072 - pm_device_init, Delta
B - 322354 - pm_driver_init, Start
D - 5337 - pm_driver_init, Delta
B - 328729 - clock_init, Start
D - 2104 - clock_init, Delta
B - 332724 - boot_flash_init, Start
D - 16531 - boot_flash_init, Delta
B - 352946 - boot_config_data_table_init, Start
D - 4026 - boot_config_data_table_init, Delta - (575 Bytes)
B - 360327 - Boot Setting : 0x00000618
B - 364444 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:0,Subtype:8
B - 371246 - sbl1_ddr_set_params, Start
B - 375058 - CPR configuration: 0x30c
B - 378535 - cpr_init, Start
B - 381311 - Rail:0 Mode: 5 Voltage: 824000
B - 386526 - CL CPR settled at 776000mV
B - 389332 - Rail:1 Mode: 5 Voltage: 880000
B - 393541 - Rail:1 Mode: 7 Voltage: 912000
D - 16531 - cpr_init, Delta
B - 400404 - Pre_DDR_clock_init, Start
B - 404430 - Pre_DDR_clock_init, End
B - 407724 - DDR Type : PCDDR3
B - 413458 - do ddr sanity test, Start
D - 1067 - do ddr sanity test, Delta
B - 418216 - DDR: Start of HAL DDR Boot Training
B - 422974 - DDR: End of HAL DDR Boot Training
B - 428647 - DDR: Checksum to be stored on flash is -2059726583
B - 439169 - Image Load, Start
D - 216245 - QSEE Image Loaded, Delta - (1374928 Bytes)
B - 655475 - Image Load, Start
D - 61 - SEC Image Loaded, Delta - (0 Bytes)
B - 663161 - Image Load, Start
D - 12017 - DEVCFG Image Loaded, Delta - (26148 Bytes)
B - 675270 - Image Load, Start
D - 23027 - RPM Image Loaded, Delta - (86660 Bytes)
B - 698389 - Image Load, Start
D - 89914 - APPSBL Image Loaded, Delta - (572642 Bytes)
B - 788455 - QSEE Execution, Start
D - 61 - QSEE Execution, Delta
B - 794250 - USB D+ check, Start
D - 0 - USB D+ check, Delta
B - 800655 - SBL1, End
D - 660417 - SBL1, Delta
S - Flash Throughput, 6899 KB/s (2061625 Bytes, 298801 us)
S - DDR Frequency, 466 MHz
S - Core 0 Frequency, 1651 MHz
U-Boot 2016.01 (Jul 25 2022 - 17:08:05 +0800)
DRAM: smem ram ptable found: ver: 1 len: 4
1 GiB
NAND: Could not find nand_gpio in dts, using defaults
Not an ONFI device
ONFI probe failed
ID = 2691a398
Vendor = 98
Device = a3
qpic_nand: changing oobsize to 160 from 256 bytes
SF: Unsupported flash IDs: manuf ff, jedec ffff, ext_jedec ffff
ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0)
1024 MiB
MMC: sdhci: Node Not found, skipping initialization
PCI0 is not defined in the device tree
PCI1 is not defined in the device tree
In: serial@78B3000
Out: serial@78B3000
Err: serial@78B3000
machid: 8010008
MMC Device 0 not found
[arc_board_setting]
[serial_register_init]
Hit any key to stop autoboot: 0
[do_boot_unsignedimg(903)] debug:0
[do_boot_unsignedimg(934)] runcmd:setenv mtdids nand0=nand0 && setenv mtdparts mtdparts=nand0:0x6400000@0x1000000(fs),${msmparts} && ubi part fs && ubi read 0x44000000 kernel &&
ubi0: attaching mtd1
ubi0: scanning is finished
ubi0: attached mtd1 (name "mtd=0", size 100 MiB)
ubi0: PEB size: 262144 bytes (256 KiB), LEB size: 253952 bytes
ubi0: min./max. I/O unit sizes: 4096/4096, sub-page size 4096
ubi0: VID header offset: 4096 (aligned 4096), data offset: 8192
ubi0: good PEBs: 400, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 6/3, WL threshold: 4096, image sequence number: 1831545825
ubi0: available PEBs: 0, total reserved PEBs: 400, PEBs reserved for bad PEB handling: 80
Read 0 bytes from volume kernel to 44000000
No size specified -> Using max size (4825088)
[do_boot_unsignedimg(1004)] mtdids:nand0=nand0
## Loading kernel from FIT Image at 44000000 ...
Using 'config@hk09' configuration
Trying 'kernel-1' kernel subimage
Description: ARM64 OpenWrt Linux-5.15.148
Type: Kernel Image
Compression: gzip compressed
Data Start: 0x440000ec
Data Size: 4550217 Bytes = 4.3 MiB
Architecture: AArch64
OS: Linux
Load Address: 0x41000000
Entry Point: 0x41000000
Hash algo: crc32
Hash value: 292e97cb
Hash algo: sha1
Hash value: cdab96d5bc4c20b4270667ae786154e62944b60d
Verifying Hash Integrity ... crc32+ sha1+ OK
## Loading fdt from FIT Image at 44000000 ...
Using 'config@hk09' configuration
Trying 'fdt-1' fdt subimage
Description: ARM64 OpenWrt arcadyan_aw1000 device tree blob
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x44457078
Data Size: 43016 Bytes = 42 KiB
Architecture: AArch64
Hash algo: crc32
Hash value: cd38ffde
Hash algo: sha1
Hash value: d85a8259ef06ed458c0410a20d3c6b10279c6545
Verifying Hash Integrity ... crc32+ sha1+ OK
Booting using the fdt blob at 0x44457078
Uncompressing Kernel Image ... OK
Loading Device Tree to 4a3f2000, end 4a3ff807 ... OK
Could not find PCI in device tree
Using machid 0x8010008 from environment
Starting kernel ...
Jumping to AARCH64 kernel via monitor
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[ 0.000000] Linux version 5.15.148 (cezary@eko.one.pl) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 12.3.0 r23004-7f0db09513) 12.3.0, GNU ld (GNU Binutils) 2.40.0) #0 SMP Thu Mar 7 21:14:32 2024
[ 0.000000] Machine model: Arcadyan AW1000
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000040000000-0x000000007fffffff]
[ 0.000000] DMA32 empty
[ 0.000000] Normal empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000040000000-0x0000000040ffffff]
[ 0.000000] node 0: [mem 0x0000000041000000-0x000000004a3fffff]
[ 0.000000] node 0: [mem 0x000000004a400000-0x00000000510fffff]
[ 0.000000] node 0: [mem 0x0000000051100000-0x000000007fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000007fffffff]
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.0 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] psci: SMC Calling Convention v1.0
[ 0.000000] percpu: Embedded 17 pages/cpu s30808 r8192 d30632 u69632
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 258048
[ 0.000000] Kernel command line: console=ttyMSM0,115200n8 pcie_dev=RG50 ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashfs rootwait root=/dev/ubiblock0_1
[ 0.000000] Unknown kernel command line parameters "pcie_dev=RG50", will be passed to user space.
[ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 888440K/1048576K available (7808K kernel code, 860K rwdata, 1400K rodata, 1280K init, 288K bss, 160136K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] Root IRQ handler: 0xffffffc00837cb10
[ 0.000000] GICv2m: range[mem 0x0b00a000-0x0b00affc], SPI[448:479]
[ 0.000000] arch_timer: cp15 and mmio timer(s) running at 19.20MHz (virt/virt).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns
[ 0.000000] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns
[ 0.000126] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=192000)
[ 0.000143] pid_max: default: 32768 minimum: 301
[ 0.000614] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.000632] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.002614] rcu: Hierarchical SRCU implementation.
[ 0.003400] smp: Bringing up secondary CPUs ...
[ 0.004033] Detected VIPT I-cache on CPU1
[ 0.004100] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[ 0.004724] Detected VIPT I-cache on CPU2
[ 0.004765] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
[ 0.005375] Detected VIPT I-cache on CPU3
[ 0.005413] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
[ 0.005478] smp: Brought up 1 node, 4 CPUs
[ 0.005506] SMP: Total of 4 processors activated.
[ 0.005514] CPU features: detected: 32-bit EL0 Support
[ 0.005521] CPU features: detected: CRC32 instructions
[ 0.005574] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching
[ 0.005583] CPU: All CPU(s) started at EL1
[ 0.005605] alternatives: patching kernel code
[ 0.015868] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.015903] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[ 0.016137] pinctrl core: initialized pinctrl subsystem
[ 0.017557] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.018109] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations
[ 0.018152] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[ 0.018189] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[ 0.018579] thermal_sys: Registered thermal governor 'step_wise'
[ 0.020305] cpuidle: using governor menu
[ 0.020568] ASID allocator initialised with 65536 entries
[ 0.048718] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4
[ 0.058733] SCSI subsystem initialized
[ 0.058931] usbcore: registered new interface driver usbfs
[ 0.058973] usbcore: registered new interface driver hub
[ 0.059010] usbcore: registered new device driver usb
[ 0.059487] qcom_scm: convention: smc arm 64
[ 0.061044] clocksource: Switched to clocksource arch_sys_counter
[ 0.061971] NET: Registered PF_INET protocol family
[ 0.062111] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 0.063156] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes, linear)
[ 0.063184] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.063200] TCP established hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.063288] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear)
[ 0.063442] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.063537] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.063579] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.063800] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.063846] PCI: CLS 0 bytes, default 64
[ 0.065226] workingset: timestamp_bits=46 max_order=18 bucket_order=0
[ 0.069884] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.069906] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.070896] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
[ 0.072056] qcom-qmp-phy 58000.phy: supply vdda-phy not found, using dummy regulator
[ 0.072262] qcom-qmp-phy 58000.phy: supply vdda-pll not found, using dummy regulator
[ 0.072757] qcom-qmp-phy 58000.phy: Registered Qcom-QMP phy
[ 0.073006] qcom-qmp-phy 78000.phy: supply vdda-phy not found, using dummy regulator
[ 0.073152] qcom-qmp-phy 78000.phy: supply vdda-pll not found, using dummy regulator
[ 0.073530] qcom-qmp-phy 78000.phy: Registered Qcom-QMP phy
[ 0.074317] qcom-qusb2-phy 59000.phy: supply vdda-pll not found, using dummy regulator
[ 0.074451] qcom-qusb2-phy 59000.phy: supply vdda-phy-dpdm not found, using dummy regulator
[ 0.074654] qcom-qusb2-phy 59000.phy: Registered Qcom-QUSB2 phy
[ 0.074837] qcom-qusb2-phy 79000.phy: supply vdda-pll not found, using dummy regulator
[ 0.074960] qcom-qusb2-phy 79000.phy: supply vdda-phy-dpdm not found, using dummy regulator
[ 0.075098] qcom-qusb2-phy 79000.phy: Registered Qcom-QUSB2 phy
[ 0.076896] gpio-export gpio-export: 4 gpio(s) exported
[ 0.078515] bam-dma-engine 704000.dma-controller: num-channels unspecified in dt
[ 0.078539] bam-dma-engine 704000.dma-controller: num-ees unspecified in dt
[ 0.082678] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.084516] msm_serial 78b3000.serial: msm_serial: detected port #0
[ 0.084559] msm_serial 78b3000.serial: uartclk = 3686400
[ 0.084609] 78b3000.serial: ttyMSM0 at MMIO 0x78b3000 (irq = 22, base_baud = 230400) is a MSM
[ 0.084641] msm_serial: console setup on port #0
[ 0.774302] printk: console [ttyMSM0] enabled
[ 0.779466] msm_serial: driver initialized
[ 0.787889] loop: module loaded
[ 0.787964] Loading iSCSI transport class v2.0-870.
[ 0.792121] nand: device found, Manufacturer ID: 0x98, Chip ID: 0xa3
[ 0.795122] nand: Toshiba NAND 1GiB 1,8V 8-bit
[ 0.801760] nand: 1024 MiB, SLC, erase size: 256 KiB, page size: 4096, OOB size: 128
[ 0.805975] nand: ECC (step, strength) = (512, 8) does not fit in OOB
[ 0.805985] qcom-nandc 79b0000.nand-controller: No valid ECC settings possible
[ 0.820286] qcom-nandc: probe of 79b0000.nand-controller failed with error -28
[ 0.827870] spmi spmi-0: PMIC arbiter version v2 (0x20010000)
[ 0.837603] s1: supplied by regulator-dummy
[ 0.840551] s2: supplied by regulator-dummy
[ 0.844516] vdd_s3: supplied by regulator-dummy
[ 0.848826] vdd_s4: supplied by regulator-dummy
[ 0.853356] s5: supplied by regulator-dummy
[ 0.857710] l1: supplied by regulator-dummy
[ 0.861913] l2: supplied by regulator-dummy
[ 0.866056] l3: supplied by regulator-dummy
[ 0.870210] l4: supplied by regulator-dummy
[ 0.874390] l5: supplied by regulator-dummy
[ 0.878578] l6: supplied by regulator-dummy
[ 0.882710] l7: supplied by regulator-dummy
[ 0.886879] l8: supplied by regulator-dummy
[ 0.891074] l9: supplied by regulator-dummy
[ 0.895332] l11: supplied by regulator-dummy
[ 0.899352] l12: supplied by regulator-dummy
[ 0.903924] l13: supplied by regulator-dummy
[ 0.923052] i2c_dev: i2c /dev entries driver
[ 0.927256] sdhci: Secure Digital Host Controller Interface driver
[ 0.927300] sdhci: Copyright(c) Pierre Ossman
[ 0.932421] sdhci-pltfm: SDHCI platform and OF driver helper
[ 0.940382] remoteproc remoteproc0: releasing cd00000.q6v5_wcss
[ 0.945268] NET: Registered PF_INET6 protocol family
[ 0.949210] Segment Routing with IPv6
[ 0.953443] In-situ OAM (IOAM) with IPv6
[ 0.957018] NET: Registered PF_PACKET protocol family
[ 0.960977] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 0.966019] 8021q: 802.1Q VLAN Support v1.8
[ 0.997108] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4
[ 0.997438] cpr4_ipq807x_apss_read_fuse_data: apc_corner: speed bin = 0
[ 1.003285] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR fusing revision = 1
[ 1.009836] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR misc fuse value = 0
[ 1.017504] cpr4_ipq807x_apss_read_fuse_data: apc_corner: Voltage boost fuse config = 0 boost = disable
[ 1.025009] cpr3_mem_acc_init: apc: not using memory accelerator regulator
[ 1.034146] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused SVS: open-loop= 704000 uV
[ 1.041095] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused NOM: open-loop= 832000 uV
[ 1.051078] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused TURBO: open-loop= 888000 uV
[ 1.060880] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused STURBO: open-loop= 976000 uV
[ 1.070753] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused SVS: quot[ 7]= 683, quot_offset[ 7]= 0
[ 1.080512] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused NOM: quot[ 7]= 935, quot_offset[ 7]= 250
[ 1.091357] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused TURBO: quot[ 7]=1031, quot_offset[ 7]= 95
[ 1.102300] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused STURBO: quot[ 7]=1194, quot_offset[ 7]= 160
[ 1.113369] cpr3_regulator_init_ctrl: apc: Default CPR mode = closed-loop
[ 1.116043] cpufreq: cpufreq_online: CPU0: Running at unlisted initial frequency: 19200 KHz, changing to: 1017600 KHz
[ 1.132029] remoteproc remoteproc0: cd00000.q6v5_wcss is availab�+HH��1.148422] Waiting for root device /dev/ubiblock0_1...
[ 31.191075] l11: disablingDodaj cały bootlog.
Dodałem.
Tak wygląda załadowany initramfs:
root@OpenWrt:~# dmesg
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[ 0.000000] Linux version 6.1.80 (builder@buildhost) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 12.3.0 r25414-22f24f9107) 12.3.0, GNU ld (GNU Binutils) 2.40.0) #0 SMP Fri Mar 8 08:51:35 2024
[ 0.000000] Machine model: Arcadyan AW1000
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000040000000-0x000000007fffffff]
[ 0.000000] DMA32 empty
[ 0.000000] Normal empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000040000000-0x0000000040ffffff]
[ 0.000000] node 0: [mem 0x0000000041000000-0x000000004a3fffff]
[ 0.000000] node 0: [mem 0x000000004a400000-0x00000000510fffff]
[ 0.000000] node 0: [mem 0x0000000051100000-0x000000007fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000007fffffff]
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.0 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] psci: SMC Calling Convention v1.0
[ 0.000000] percpu: Embedded 18 pages/cpu s34664 r8192 d30872 u73728
[ 0.000000] pcpu-alloc: s34664 r8192 d30872 u73728 alloc=18*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] alternatives: applying boot alternatives
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 258048
[ 0.000000] Kernel command line: console=ttyMSM0,115200n8 pcie_dev=RG50 root=/dev/ubiblock0_1
[ 0.000000] Unknown kernel command line parameters "pcie_dev=RG50", will be passed to user space.
[ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 879648K/1048576K available (8192K kernel code, 900K rwdata, 2408K rodata, 8640K init, 293K bss, 168928K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] Root IRQ handler: gic_handle_irq
[ 0.000000] GICv2m: range[mem 0x0b00a000-0x0b00affc], SPI[448:479]
[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[ 0.000000] arch_timer: cp15 and mmio timer(s) running at 19.20MHz (virt/virt).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns
[ 0.000001] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns
[ 0.000123] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=192000)
[ 0.000137] pid_max: default: 32768 minimum: 301
[ 0.000603] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.000617] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.002462] cblist_init_generic: Setting adjustable number of callback queues.
[ 0.002469] cblist_init_generic: Setting shift to 2 and lim to 1.
[ 0.002664] rcu: Hierarchical SRCU implementation.
[ 0.002668] rcu: Max phase no-delay instances is 1000.
[ 0.003467] smp: Bringing up secondary CPUs ...
[ 0.004102] Detected VIPT I-cache on CPU1
[ 0.004243] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[ 0.004905] Detected VIPT I-cache on CPU2
[ 0.005010] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
[ 0.005626] Detected VIPT I-cache on CPU3
[ 0.005723] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
[ 0.005791] smp: Brought up 1 node, 4 CPUs
[ 0.005799] SMP: Total of 4 processors activated.
[ 0.005804] CPU features: detected: 32-bit EL0 Support
[ 0.005808] CPU features: detected: CRC32 instructions
[ 0.005871] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching
[ 0.005878] CPU: All CPU(s) started at EL1
[ 0.005880] alternatives: applying system-wide alternatives
[ 0.016453] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.016481] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[ 0.016693] pinctrl core: initialized pinctrl subsystem
[ 0.018123] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.018655] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations
[ 0.018700] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[ 0.018735] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[ 0.019118] thermal_sys: Registered thermal governor 'step_wise'
[ 0.019299] cpuidle: using governor menu
[ 0.019563] ASID allocator initialised with 65536 entries
[ 0.073240] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4
[ 0.082290] SCSI subsystem initialized
[ 0.082474] usbcore: registered new interface driver usbfs
[ 0.082550] usbcore: registered new interface driver hub
[ 0.082597] usbcore: registered new device driver usb
[ 0.083037] qcom_scm: convention: smc arm 64
[ 0.084582] clocksource: Switched to clocksource arch_sys_counter
[ 0.085737] NET: Registered PF_INET protocol family
[ 0.085881] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 0.087315] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes, linear)
[ 0.087339] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.087353] TCP established hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.087440] TCP bind hash table entries: 8192 (order: 6, 262144 bytes, linear)
[ 0.087715] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.087817] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.087855] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.088069] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.088106] PCI: CLS 0 bytes, default 64
[ 0.089378] workingset: timestamp_bits=46 max_order=18 bucket_order=0
[ 0.094399] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.094414] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.095508] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
[ 0.097788] qcom-qmp-usb-phy 58000.phy: supply vdda-phy not found, using dummy regulator
[ 0.097953] qcom-qmp-usb-phy 58000.phy: supply vdda-pll not found, using dummy regulator
[ 0.099529] qcom-qmp-usb-phy 78000.phy: supply vdda-phy not found, using dummy regulator
[ 0.099673] qcom-qmp-usb-phy 78000.phy: supply vdda-pll not found, using dummy regulator
[ 0.101483] qcom-qusb2-phy 59000.phy: supply vdd not found, using dummy regulator
[ 0.101689] qcom-qusb2-phy 59000.phy: supply vdda-pll not found, using dummy regulator
[ 0.101747] qcom-qusb2-phy 59000.phy: supply vdda-phy-dpdm not found, using dummy regulator
[ 0.101924] qcom-qusb2-phy 59000.phy: Registered Qcom-QUSB2 phy
[ 0.102156] qcom-qusb2-phy 79000.phy: supply vdd not found, using dummy regulator
[ 0.102261] qcom-qusb2-phy 79000.phy: supply vdda-pll not found, using dummy regulator
[ 0.102333] qcom-qusb2-phy 79000.phy: supply vdda-phy-dpdm not found, using dummy regulator
[ 0.102525] qcom-qusb2-phy 79000.phy: Registered Qcom-QUSB2 phy
[ 0.104652] gpio-export gpio-export: 4 gpio(s) exported
[ 0.108287] bam-dma-engine 704000.dma-controller: num-channels unspecified in dt
[ 0.108304] bam-dma-engine 704000.dma-controller: num-ees unspecified in dt
[ 0.112961] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.115174] msm_serial 78b3000.serial: msm_serial: detected port #0
[ 0.115215] msm_serial 78b3000.serial: uartclk = 3686400
[ 0.115317] 78b3000.serial: ttyMSM0 at MMIO 0x78b3000 (irq = 21, base_baud = 230400) is a MSM
[ 0.115346] msm_serial: console setup on port #0
[ 0.835658] printk: console [ttyMSM0] enabled
[ 0.840818] msm_serial: driver initialized
[ 0.849585] loop: module loaded
[ 0.849660] Loading iSCSI transport class v2.0-870.
[ 0.853281] nand: device found, Manufacturer ID: 0x98, Chip ID: 0xa3
[ 0.856512] nand: Toshiba TH58NYG3S0HBAI4 8G 1.8V 8-bit
[ 0.863068] nand: 1024 MiB, SLC, erase size: 256 KiB, page size: 4096, OOB size: 256
[ 0.878825] spmi spmi-0: PMIC arbiter version v2 (0x20010000)
[ 0.985857] i2c_dev: i2c /dev entries driver
[ 0.991963] sdhci: Secure Digital Host Controller Interface driver
[ 0.992008] sdhci: Copyright(c) Pierre Ossman
[ 0.997081] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.003309] remoteproc remoteproc0: releasing cd00000.q6v5_wcss
[ 1.010416] NET: Registered PF_INET6 protocol family
[ 1.013871] Segment Routing with IPv6
[ 1.018127] In-situ OAM (IOAM) with IPv6
[ 1.021684] NET: Registered PF_PACKET protocol family
[ 1.025651] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 1.030680] 8021q: 802.1Q VLAN Support v1.8
[ 1.065381] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4
[ 1.065705] cpr4_ipq807x_apss_read_fuse_data: apc_corner: speed bin = 0
[ 1.071508] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR fusing revision = 1
[ 1.078124] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR misc fuse value = 0
[ 1.085776] cpr4_ipq807x_apss_read_fuse_data: apc_corner: Voltage boost fuse config = 0 boost = disable
[ 1.093291] cpr3_mem_acc_init: apc: not using memory accelerator regulator
[ 1.102421] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused SVS: open-loop= 704000 uV
[ 1.109367] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused NOM: open-loop= 832000 uV
[ 1.119350] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused TURBO: open-loop= 888000 uV
[ 1.129158] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused STURBO: open-loop= 976000 uV
[ 1.139019] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused SVS: quot[ 7]= 683, quot_offset[ 7]= 0
[ 1.148780] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused NOM: quot[ 7]= 935, quot_offset[ 7]= 250
[ 1.159630] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused TURBO: quot[ 7]=1031, quot_offset[ 7]= 95
[ 1.170567] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused STURBO: quot[ 7]=1194, quot_offset[ 7]= 160
[ 1.181703] cpr3_regulator_init_ctrl: apc: Default CPR mode = closed-loop
[ 1.184134] nand: device found, Manufacturer ID: 0x98, Chip ID: 0xa3
[ 1.199216] nand: Toshiba TH58NYG3S0HBAI4 8G 1.8V 8-bit
[ 1.205639] nand: 1024 MiB, SLC, erase size: 256 KiB, page size: 4096, OOB size: 256
[ 1.220102] 26 qcomsmem partitions found on MTD device qcom_nand.0
[ 1.220150] Creating 26 MTD partitions on "qcom_nand.0":
[ 1.225234] 0x000000000000-0x000000100000 : "0:sbl1"
[ 1.231740] 0x000000100000-0x000000200000 : "0:mibib"
[ 1.236577] 0x000000200000-0x000000280000 : "0:bootconfig"
[ 1.241218] 0x000000280000-0x000000300000 : "0:bootconfig1"
[ 1.246667] 0x000000300000-0x000000600000 : "0:qsee"
[ 1.253072] 0x000000600000-0x000000900000 : "0:qsee_1"
[ 1.258347] 0x000000900000-0x000000980000 : "0:devcfg"
[ 1.262215] 0x000000980000-0x000000a00000 : "0:devcfg_1"
[ 1.267409] 0x000000a00000-0x000000a80000 : "0:apdp"
[ 1.272828] 0x000000a80000-0x000000b00000 : "0:apdp_1"
[ 1.277838] 0x000000b00000-0x000000b80000 : "0:rpm"
[ 1.282702] 0x000000b80000-0x000000c00000 : "0:rpm_1"
[ 1.287536] 0x000000c00000-0x000000c80000 : "0:cdt"
[ 1.292701] 0x000000c80000-0x000000d00000 : "0:cdt_1"
[ 1.297506] 0x000000d00000-0x000000d80000 : "0:appsblenv"
[ 1.302634] 0x000000d80000-0x000000e80000 : "0:appsbl"
[ 1.308261] 0x000000e80000-0x000000f80000 : "0:appsbl_1"
[ 1.313281] 0x000000f80000-0x000001000000 : "0:art"
[ 1.318563] 0x000001000000-0x000007400000 : "rootfs"
[ 1.364147] mtd: setting mtd18 (rootfs) as root device
[ 1.364692] mtdsplit: no squashfs found in "rootfs"
[ 1.368223] 0x000007400000-0x000008c80000 : "0:wififw"
[ 1.383411] 0x000008c80000-0x00000f080000 : "rootfs_1"
[ 1.425171] 0x00000f080000-0x000010900000 : "0:wififw_1"
[ 1.436025] 0x000010900000-0x000010b40000 : "0:ethphyfw"
[ 1.437521] 0x000010b40000-0x000010c40000 : "0:board_data"
[ 1.441301] 0x000010c40000-0x000011440000 : "0:arc_datadump"
[ 1.449478] 0x000011440000-0x00003e000000 : "0:arc_data"
[ 1.756180] cpufreq: cpufreq_online: CPU0: Running at unlisted initial frequency: 800000 KHz, changing to: 1017600 KHz
[ 1.758085] remoteproc remoteproc0: cd00000.q6v5_wcss is available
[ 1.769532] Freeing unused kernel memory: 8640K
[ 1.814763] Run /init as init process
[ 1.814798] with arguments:
[ 1.814802] /init
[ 1.814805] with environment:
[ 1.814808] HOME=/
[ 1.814811] TERM=linux
[ 1.814814] pcie_dev=RG50
[ 1.982305] init: Console is alive
[ 1.982472] init: - watchdog -
[ 1.990721] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 2.012238] ssdk_dt_parse_interrupt[935]:INFO:intr-gpio does not exist
[ 3.144692] regi_init[3603]:INFO:Initializing HPPE Done!!
[ 3.144821] regi_init[3662]:INFO:qca-ssdk module init succeeded!
[ 3.151207] EDMA ver 1 hw init
[ 3.155393] EDMA HW Reset completed succesfully
[ 3.158048] Num rings - TxDesc:1 (23-23) TxCmpl:1 (7-7)
[ 3.162445] RxDesc:1 (15-15) RxFill:1 (7-7)
[ 3.687247] **********************************************************
[ 3.687286] * NSS Data Plane driver
[ 3.692663] **********************************************************
[ 3.710582] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 3.710629] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 1
[ 3.715120] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220fe65 hci version 0x110 quirks 0x0000008002010010
[ 3.722556] xhci-hcd xhci-hcd.1.auto: irq 41, io mem 0x08a00000
[ 3.731981] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 3.737800] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 2
[ 3.743355] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed
[ 3.751433] hub 1-0:1.0: USB hub found
[ 3.757600] hub 1-0:1.0: 1 port detected
[ 3.761485] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 3.765711] hub 2-0:1.0: USB hub found
[ 3.773401] hub 2-0:1.0: 1 port detected
[ 3.777280] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller
[ 3.781029] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 3
[ 3.786462] xhci-hcd xhci-hcd.2.auto: hcc params 0x0220fe65 hci version 0x110 quirks 0x0000008002010010
[ 3.793917] xhci-hcd xhci-hcd.2.auto: irq 42, io mem 0x08c00000
[ 3.803344] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller
[ 3.809155] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 4
[ 3.814713] xhci-hcd xhci-hcd.2.auto: Host supports USB 3.0 SuperSpeed
[ 3.822729] hub 3-0:1.0: USB hub found
[ 3.829007] hub 3-0:1.0: 1 port detected
[ 3.832931] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[ 3.836974] hub 4-0:1.0: USB hub found
[ 3.844763] hub 4-0:1.0: 1 port detected
[ 3.849600] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 3.857869] init: - preinit -
[ 8.414574] random: crng init done
[ 10.538825] procd: - early -
[ 10.538913] procd: - watchdog -
[ 10.634737] usb 4-1: new SuperSpeed USB device number 2 using xhci-hcd
[ 11.169261] procd: - watchdog -
[ 11.169493] procd: - ubus -
[ 11.222738] procd: - init -
[ 11.352316] kmodloader: loading kernel modules from /etc/modules.d/*
[ 11.378904] Loading modules backported from Linux version v6.6.15-0-g51f354b815c4
[ 11.378945] Backport generated by backports.git 193becf2
[ 11.389346] NET: Registered PF_QIPCRTR protocol family
[ 11.414773] PPP generic driver version 2.4.2
[ 11.415443] NET: Registered PF_PPPOX protocol family
[ 11.423613] ath11k c000000.wifi: ipq8074 hw2.0
[ 11.423646] ath11k c000000.wifi: FW memory mode: 0
[ 11.427661] remoteproc remoteproc0: powering up cd00000.q6v5_wcss
[ 11.432153] remoteproc remoteproc0: Booting fw image IPQ8074/q6_fw.mdt, size 668
[ 11.509799] urngd: v1.0.2 started.
[ 11.783297] remoteproc remoteproc0: remote processor cd00000.q6v5_wcss is now up
[ 11.786903] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 11.828715] ath11k c000000.wifi: qmi ignore invalid mem req type 3
[ 11.836142] ath11k c000000.wifi: chip_id 0x0 chip_family 0x0 board_id 0x270 soc_id 0xffffffff
[ 11.836178] ath11k c000000.wifi: fw_version 0x290104a5 fw_build_timestamp 2023-08-02 20:32 fw_build_id WLAN.HK.2.9.0.1-01890-QCAHKSWPL_SILICONZ-1
[ 11.906340] ath11k c000000.wifi: failed to fetch board data for bus=ahb,qmi-chip-id=0,qmi-board-id=624,variant=Arcadyan-AW1000 from ath11k/IPQ8074/hw2.0/board-2.bin
[ 11.906403] ath11k c000000.wifi: failed to fetch board data for bus=ahb,qmi-chip-id=0,qmi-board-id=624 from ath11k/IPQ8074/hw2.0/board-2.bin
[ 11.920207] ath11k c000000.wifi: failed to fetch board data for bus=ahb,qmi-chip-id=0,qmi-board-id=624 from ath11k/IPQ8074/hw2.0/board-2.bin
[ 11.932729] ath11k c000000.wifi: failed to fetch board.bin from IPQ8074/hw2.0
[ 11.945302] ath11k c000000.wifi: qmi failed to fetch board file: -12
[ 11.952310] ath11k c000000.wifi: failed to load board data file: -12
[ 14.844547] br-lan: port 1(lan1) entered blocking state
[ 14.844624] br-lan: port 1(lan1) entered disabled state
[ 14.848837] device lan1 entered promiscuous mode
[ 14.860242] br-lan: port 2(lan2) entered blocking state
[ 14.860284] br-lan: port 2(lan2) entered disabled state
[ 14.864486] device lan2 entered promiscuous mode
[ 14.873532] br-lan: port 3(lan3) entered blocking state
[ 14.874353] br-lan: port 3(lan3) entered disabled state
[ 14.879559] device lan3 entered promiscuous mode
[ 14.887722] br-lan: port 4(lan4) entered blocking state
[ 14.889374] br-lan: port 4(lan4) entered disabled state
[ 14.894517] device lan4 entered promiscuous mode
[ 17.995251] nss-dp 3a001000.dp1 lan1: PHY Link up speed: 1000
[ 17.995330] br-lan: port 1(lan1) entered blocking state
[ 17.999985] br-lan: port 1(lan1) entered forwarding state
[ 18.005260] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 22.234955] platform leds: deferred probe pending
[ 31.834629] l11: disabling
root@OpenWrt:~# Czyli czeka na roota z ubiblock0_1 ,jak jeszcze nanda nie odczytał?
EDIT: Chociaż probowal:
[ 0.820286] qcom-nandc: probe of 79b0000.nand-controller failed with error -28
Może tu coś ciekawego będzie, tak wygląda sysupgrade (mifi) z poziomu konsoli:
root@OpenWrt:/# Watchdog handover: fd=3
- watchdog -
Watchdog did not previously reset the system
Fri Mar 8 08:56:44 UTC 2024 upgrade: Sending TERM to remaining processes ...
Fri Mar 8 08:56:44 UTC 2024 upgrade: Sending signal TERM to netifd (2022)
Fri Mar 8 08:56:48 UTC 2024 upgrade: Sending KILL to remaining processes ...
Fri Mar 8 08:56:48 UTC 2024 upgrade: Sending signal KILL to netifd (2022)
[ 329.579890] stage2 (3126): drop_caches: 3
Fri Mar 8 08:56:56 UTC 2024 upgrade: Switching to ramdisk...
[ 331.101825] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" stops
[ 331.109913] UBIFS (ubi0:2): un-mount UBI device 0
Fri Mar 8 08:56:57 UTC 2024 upgrade: Performing system upgrade...
verifying sysupgrade tar file integrity
[ 331.607351] block ubiblock0_1: released
Volume ID 0, size 19 LEBs (4825088 bytes, 4.6 MiB), LEB size 253952 bytes (248.0 KiB), dynamic, name "kernel", alignment 1
[ 331.859100] block ubiblock0_1: created from ubi0:1(rootfs)
Volume ID 1, size 37 LEBs (9396224 bytes, 8.9 MiB), LEB size 253952 bytes (248.0 KiB), dynamic, name "rootfs", alignment 1
Set volume size to 66027520
Volume ID 2, size 260 LEBs (66027520 bytes, 62.9 MiB), LEB size 253952 bytes (248.0 KiB), dynamic, name "rootfs_data", alignment 1
sysupgrade successful
umount: can't unmount /dev: Resource busy
umount: can't unmount /tmp: Resource busy
[ 334.452822] remoteproc remoteproc0: stopped remote processor cd00000.q6v5_wcss
[ 334.967538] reboot: Restarting system
Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.3.1-00163
S - IMAGE_VARIANT_STRING=HAACANAZA
S - OEM_IMAGE_VERSION_STRING=CRM
S - Boot Config, 0x000002e5
B - 201 - PBL, Start
B - 2736 - bootable_media_detect_entry, Start
B - 3449 - bootable_media_detect_success, Start
B - 3454 - elf_loader_entry, Start
B - 7636 - auth_hash_seg_entry, Start
B - 7884 - auth_hash_seg_exit, Start
B - 69785 - elf_segs_hash_verify_entry, Start
B - 132640 - PBL, End
B - 214049 - SBL1, Start
B - 291275 - GCC [RstStat:0x10, RstDbg:0x600000] WDog Stat : 0x4
B - 300913 - pm_device_init, Start
B - 480222 - PM_SET_VAL:Skip
D - 177510 - pm_device_init, Delta
B - 482662 - pm_driver_init, Start
D - 5398 - pm_driver_init, Delta
B - 488976 - clock_init, Start
D - 2135 - clock_init, Delta
B - 493002 - boot_flash_init, Start
D - 16531 - boot_flash_init, Delta
B - 513223 - boot_config_data_table_init, Start
D - 3995 - boot_config_data_table_init, Delta - (575 Bytes)
B - 520604 - Boot Setting : 0x00000618
B - 524722 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:0,Subtype:8
B - 531523 - sbl1_ddr_set_params, Start
B - 535336 - CPR configuration: 0x30c
B - 538782 - cpr_init, Start
B - 541588 - Rail:0 Mode: 5 Voltage: 824000
B - 546804 - CL CPR settled at 776000mV
B - 549610 - Rail:1 Mode: 5 Voltage: 880000
B - 553788 - Rail:1 Mode: 7 Voltage: 912000
D - 16531 - cpr_init, Delta
B - 560681 - Pre_DDR_clock_init, Start
B - 564707 - Pre_DDR_clock_init, End
B - 568001 - DDR Type : PCDDR3
B - 573735 - do ddr sanity test, Start
D - 1067 - do ddr sanity test, Delta
B - 578493 - DDR: Start of HAL DDR Boot Training
B - 583221 - DDR: End of HAL DDR Boot Training
B - 588924 - DDR: Checksum to be stored on flash is -2059726583
B - 599416 - Image Load, Start
D - 216245 - QSEE Image Loaded, Delta - (1374928 Bytes)
B - 815753 - Image Load, Start
D - 61 - SEC Image Loaded, Delta - (0 Bytes)
B - 823439 - Image Load, Start
D - 12017 - DEVCFG Image Loaded, Delta - (26148 Bytes)
B - 835547 - Image Load, Start
D - 23028 - RPM Image Loaded, Delta - (86660 Bytes)
B - 858666 - Image Load, Start
D - 89884 - APPSBL Image Loaded, Delta - (572642 Bytes)
B - 948702 - QSEE Execution, Start
D - 91 - QSEE Execution, Delta
B - 954497 - USB D+ check, Start
D - 0 - USB D+ check, Delta
B - 960902 - SBL1, End
D - 749141 - SBL1, Delta
S - Flash Throughput, 6898 KB/s (2061625 Bytes, 298831 us)
S - DDR Frequency, 466 MHz
S - Core 0 Frequency, 1651 MHz
U-Boot 2016.01 (Jul 25 2022 - 17:08:05 +0800)
DRAM: smem ram ptable found: ver: 1 len: 4
1 GiB
NAND: Could not find nand_gpio in dts, using defaults
Not an ONFI device
ONFI probe failed
ID = 2691a398
Vendor = 98
Device = a3
qpic_nand: changing oobsize to 160 from 256 bytes
SF: Unsupported flash IDs: manuf ff, jedec ffff, ext_jedec ffff
ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0)
1024 MiB
MMC: sdhci: Node Not found, skipping initialization
PCI0 is not defined in the device tree
PCI1 is not defined in the device tree
In: serial@78B3000
Out: serial@78B3000
Err: serial@78B3000
machid: 8010008
MMC Device 0 not found
[arc_board_setting]
[serial_register_init]
Hit any key to stop autoboot: 0
[do_boot_unsignedimg(903)] debug:0
[do_boot_unsignedimg(934)] runcmd:setenv mtdids nand0=nand0 && setenv mtdparts mtdparts=nand0:0x6400000@0x1000000(fs),${msmparts} && ubi part fs && ubi read 0x44000000 kernel &&
ubi0: attaching mtd1
ubi0: scanning is finished
ubi0: attached mtd1 (name "mtd=0", size 100 MiB)
ubi0: PEB size: 262144 bytes (256 KiB), LEB size: 253952 bytes
ubi0: min./max. I/O unit sizes: 4096/4096, sub-page size 4096
ubi0: VID header offset: 4096 (aligned 4096), data offset: 8192
ubi0: good PEBs: 400, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 6/3, WL threshold: 4096, image sequence number: 1831545825
ubi0: available PEBs: 0, total reserved PEBs: 400, PEBs reserved for bad PEB handling: 80
Read 0 bytes from volume kernel to 44000000
No size specified -> Using max size (4825088)
[do_boot_unsignedimg(1004)] mtdids:nand0=nand0
## Loading kernel from FIT Image at 44000000 ...
Using 'config@hk09' configuration
Trying 'kernel-1' kernel subimage
Description: ARM64 OpenWrt Linux-5.15.148
Type: Kernel Image
Compression: gzip compressed
Data Start: 0x440000ec
Data Size: 4550217 Bytes = 4.3 MiB
Architecture: AArch64
OS: Linux
Load Address: 0x41000000
Entry Point: 0x41000000
Hash algo: crc32
Hash value: 292e97cb
Hash algo: sha1
Hash value: cdab96d5bc4c20b4270667ae786154e62944b60d
Verifying Hash Integrity ... crc32+ sha1+ OK
## Loading fdt from FIT Image at 44000000 ...
Using 'config@hk09' configuration
Trying 'fdt-1' fdt subimage
Description: ARM64 OpenWrt arcadyan_aw1000 device tree blob
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x44457078
Data Size: 43016 Bytes = 42 KiB
Architecture: AArch64
Hash algo: crc32
Hash value: cd38ffde
Hash algo: sha1
Hash value: d85a8259ef06ed458c0410a20d3c6b10279c6545
Verifying Hash Integrity ... crc32+ sha1+ OK
Booting using the fdt blob at 0x44457078
Uncompressing Kernel Image ... OK
Loading Device Tree to 4a3f2000, end 4a3ff807 ... OK
Could not find PCI in device tree
Using machid 0x8010008 from environment
Starting kernel ...
Jumping to AARCH64 kernel via monitor
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[ 0.000000] Linux version 5.15.148 (cezary@eko.one.pl) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 12.3.0 r23004-7f0db09513) 12.3.0, GNU ld (GNU Binutils) 2.40.0) #0 SMP Thu Mar 7 21:14:32 2024
[ 0.000000] Machine model: Arcadyan AW1000
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000040000000-0x000000007fffffff]
[ 0.000000] DMA32 empty
[ 0.000000] Normal empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000040000000-0x0000000040ffffff]
[ 0.000000] node 0: [mem 0x0000000041000000-0x000000004a3fffff]
[ 0.000000] node 0: [mem 0x000000004a400000-0x00000000510fffff]
[ 0.000000] node 0: [mem 0x0000000051100000-0x000000007fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000007fffffff]
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.0 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] psci: SMC Calling Convention v1.0
[ 0.000000] percpu: Embedded 17 pages/cpu s30808 r8192 d30632 u69632
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 258048
[ 0.000000] Kernel command line: console=ttyMSM0,115200n8 pcie_dev=RG50 ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashfs rootwait root=/dev/ubiblock0_1
[ 0.000000] Unknown kernel command line parameters "pcie_dev=RG50", will be passed to user space.
[ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 888440K/1048576K available (7808K kernel code, 860K rwdata, 1400K rodata, 1280K init, 288K bss, 160136K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] Root IRQ handler: 0xffffffc00837cb10
[ 0.000000] GICv2m: range[mem 0x0b00a000-0x0b00affc], SPI[448:479]
[ 0.000000] arch_timer: cp15 and mmio timer(s) running at 19.20MHz (virt/virt).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns
[ 0.000000] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns
[ 0.000127] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=192000)
[ 0.000144] pid_max: default: 32768 minimum: 301
[ 0.000610] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.000628] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.002616] rcu: Hierarchical SRCU implementation.
[ 0.003417] smp: Bringing up secondary CPUs ...
[ 0.004046] Detected VIPT I-cache on CPU1
[ 0.004114] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[ 0.004738] Detected VIPT I-cache on CPU2
[ 0.004779] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
[ 0.005387] Detected VIPT I-cache on CPU3
[ 0.005424] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
[ 0.005489] smp: Brought up 1 node, 4 CPUs
[ 0.005517] SMP: Total of 4 processors activated.
[ 0.005525] CPU features: detected: 32-bit EL0 Support
[ 0.005532] CPU features: detected: CRC32 instructions
[ 0.005585] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching
[ 0.005594] CPU: All CPU(s) started at EL1
[ 0.005615] alternatives: patching kernel code
[ 0.015874] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.015909] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[ 0.016146] pinctrl core: initialized pinctrl subsystem
[ 0.017571] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.018120] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations
[ 0.018163] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[ 0.018200] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[ 0.018589] thermal_sys: Registered thermal governor 'step_wise'
[ 0.020327] cpuidle: using governor menu
[ 0.020593] ASID allocator initialised with 65536 entries
[ 0.048710] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4
[ 0.058722] SCSI subsystem initialized
[ 0.058921] usbcore: registered new interface driver usbfs
[ 0.058963] usbcore: registered new interface driver hub
[ 0.059000] usbcore: registered new device driver usb
[ 0.059472] qcom_scm: convention: smc arm 64
[ 0.061028] clocksource: Switched to clocksource arch_sys_counter
[ 0.061961] NET: Registered PF_INET protocol family
[ 0.062100] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 0.063146] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes, linear)
[ 0.063174] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.063190] TCP established hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.063278] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear)
[ 0.063428] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.063525] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.063566] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.063787] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.063833] PCI: CLS 0 bytes, default 64
[ 0.065136] workingset: timestamp_bits=46 max_order=18 bucket_order=0
[ 0.069956] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.069979] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.071007] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
[ 0.072152] qcom-qmp-phy 58000.phy: supply vdda-phy not found, using dummy regulator
[ 0.072319] qcom-qmp-phy 58000.phy: supply vdda-pll not found, using dummy regulator
[ 0.072815] qcom-qmp-phy 58000.phy: Registered Qcom-QMP phy
[ 0.073076] qcom-qmp-phy 78000.phy: supply vdda-phy not found, using dummy regulator
[ 0.073210] qcom-qmp-phy 78000.phy: supply vdda-pll not found, using dummy regulator
[ 0.073615] qcom-qmp-phy 78000.phy: Registered Qcom-QMP phy
[ 0.074411] qcom-qusb2-phy 59000.phy: supply vdda-pll not found, using dummy regulator
[ 0.074529] qcom-qusb2-phy 59000.phy: supply vdda-phy-dpdm not found, using dummy regulator
[ 0.074687] qcom-qusb2-phy 59000.phy: Registered Qcom-QUSB2 phy
[ 0.074890] qcom-qusb2-phy 79000.phy: supply vdda-pll not found, using dummy regulator
[ 0.075015] qcom-qusb2-phy 79000.phy: supply vdda-phy-dpdm not found, using dummy regulator
[ 0.075173] qcom-qusb2-phy 79000.phy: Registered Qcom-QUSB2 phy
[ 0.076937] gpio-export gpio-export: 4 gpio(s) exported
[ 0.078550] bam-dma-engine 704000.dma-controller: num-channels unspecified in dt
[ 0.078574] bam-dma-engine 704000.dma-controller: num-ees unspecified in dt
[ 0.082715] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.084500] msm_serial 78b3000.serial: msm_serial: detected port #0
[ 0.084550] msm_serial 78b3000.serial: uartclk = 3686400
[ 0.084597] 78b3000.serial: ttyMSM0 at MMIO 0x78b3000 (irq = 22, base_baud = 230400) is a MSM
[ 0.084629] msm_serial: console setup on port #0
[ 0.774295] printk: console [ttyMSM0] enabled
[ 0.779420] msm_serial: driver initialized
[ 0.787844] loop: module loaded
[ 0.787930] Loading iSCSI transport class v2.0-870.
[ 0.792187] nand: device found, Manufacturer ID: 0x98, Chip ID: 0xa3
[ 0.795111] nand: Toshiba NAND 1GiB 1,8V 8-bit
[ 0.801722] nand: 1024 MiB, SLC, erase size: 256 KiB, page size: 4096, OOB size: 128
[ 0.805964] nand: ECC (step, strength) = (512, 8) does not fit in OOB
[ 0.805974] qcom-nandc 79b0000.nand-controller: No valid ECC settings possible
[ 0.820260] qcom-nandc: probe of 79b0000.nand-controller failed with error -28
[ 0.827915] spmi spmi-0: PMIC arbiter version v2 (0x20010000)
[ 0.837585] s1: supplied by regulator-dummy
[ 0.840544] s2: supplied by regulator-dummy
[ 0.844505] vdd_s3: supplied by regulator-dummy
[ 0.848806] vdd_s4: supplied by regulator-dummy
[ 0.853375] s5: supplied by regulator-dummy
[ 0.857711] l1: supplied by regulator-dummy
[ 0.861877] l2: supplied by regulator-dummy
[ 0.866045] l3: supplied by regulator-dummy
[ 0.870192] l4: supplied by regulator-dummy
[ 0.874367] l5: supplied by regulator-dummy
[ 0.878567] l6: supplied by regulator-dummy
[ 0.882698] l7: supplied by regulator-dummy
[ 0.886878] l8: supplied by regulator-dummy
[ 0.891076] l9: supplied by regulator-dummy
[ 0.895303] l11: supplied by regulator-dummy
[ 0.899408] l12: supplied by regulator-dummy
[ 0.903884] l13: supplied by regulator-dummy
[ 0.923057] i2c_dev: i2c /dev entries driver
[ 0.927361] sdhci: Secure Digital Host Controller Interface driver
[ 0.927402] sdhci: Copyright(c) Pierre Ossman
[ 0.932483] sdhci-pltfm: SDHCI platform and OF driver helper
[ 0.940376] remoteproc remoteproc0: releasing cd00000.q6v5_wcss
[ 0.945425] NET: Registered PF_INET6 protocol family
[ 0.949169] Segment Routing with IPv6
[ 0.953499] In-situ OAM (IOAM) with IPv6
[ 0.957070] NET: Registered PF_PACKET protocol family
[ 0.961042] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 0.966061] 8021q: 802.1Q VLAN Support v1.8
[ 0.997310] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4
[ 0.997608] cpr4_ipq807x_apss_read_fuse_data: apc_corner: speed bin = 0
[ 1.003482] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR fusing revision = 1
[ 1.010035] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR misc fuse value = 0
[ 1.017705] cpr4_ipq807x_apss_read_fuse_data: apc_corner: Voltage boost fuse config = 0 boost = disable
[ 1.025209] cpr3_mem_acc_init: apc: not using memory accelerator regulator
[ 1.034347] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused SVS: open-loop= 704000 uV
[ 1.041296] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused NOM: open-loop= 832000 uV
[ 1.051278] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused TURBO: open-loop= 888000 uV
[ 1.061086] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused STURBO: open-loop= 976000 uV
[ 1.070938] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused SVS: quot[ 7]= 683, quot_offset[ 7]= 0
[ 1.080707] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused NOM: quot[ 7]= 935, quot_offset[ 7]= 250
[ 1.091557] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused TURBO: quot[ 7]=1031, quot_offset[ 7]= 95
[ 1.102496] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused STURBO: quot[ 7]=1194, quot_offset[ 7]= 160
[ 1.113571] cpr3_regulator_init_ctrl: apc: Default CPR mode = closed-loop
[ 1.116283] cpufreq: cpufreq_online: CPU0: Running at unlisted initial frequency: 19200 KHz, changing to: 1017600 KHz
[ 1.132203] remoteproc remoteproc0: cd00000.q6v5_wcss is availab[ 1.148614] Waiting for root device /dev/ubiblock0_1...
[ 31.191059] l11: disablingMoże w rooterze jest jeszcze jakaś łatka którą nie przeniosłem. Zobaczę.
Taki commit znalazłem:
https://github.com/ofmodemsandmen/ROOte … 95a80d951d
Ciekawe dlaczego usunęli??
Czy MC888 to wciąż najlepsza opcja dla domowego routera 5G? Myślałem, żeby postawić go w trybie bridge a dalej pociągnąć to na D-Link COVR AX1800 w małym domku.
Czy MC888 to wciąż najlepsza opcja dla domowego routera 5G? Myślałem, żeby postawić go w trybie bridge a dalej pociągnąć to na D-Link COVR AX1800 w małym domku.
Pod openwrt to nie 
Skubi napisał/a:Czy MC888 to wciąż najlepsza opcja dla domowego routera 5G? Myślałem, żeby postawić go w trybie bridge a dalej pociągnąć to na D-Link COVR AX1800 w małym domku.
Pod openwrt to nie
Ustawiony w trybie bridge, gdzie D-Linki na Openwrt to by nie było? 
Strony Poprzednia 1 2 3 4
Zaloguj się lub zarejestruj by napisać odpowiedź
eko.one.pl → Sprzęt / Hardware → Router domowyz 5G
Forum oparte o PunBB, wspierane przez Informer Technologies, Inc