Odp: Arcadyan AW1000
To teraz jeszcze bootipq debug.
Strony Poprzednia 1 … 5 6 7 8 9 … 33 Następna
Zaloguj się lub zarejestruj by napisać odpowiedź
Nie jesteś zalogowany. Proszę się zalogować lub zarejestrować.
Arcadyan AW1000 (Strona 7 z 33)
eko.one.pl → Sprzęt / Hardware → Arcadyan AW1000
Posty: 151 do 175 z 823
Odp: Arcadyan AW1000
samo bootipq po prostu startuje system, z debug chyba nic więcej nie ma
IPQ807x# bootipq debug
[do_boot_unsignedimg(903)] debug:1
bootargs=console=ttyMSM0,115200n8 pcie_dev=RG50 ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashfs rootwait
Booting from flash
Using nand device 0
[do_boot_unsignedimg(934)] runcmd:setenv mtdids nand0=nand0 && setenv mtdparts mtdparts=nand0:0x6400000@0x1000000(fs),${msmparts} && ubi part fs && ubi read 0x44000000 kernel &&
ubi0: attaching mtd1
ubi0: scanning is finished
ubi0: attached mtd1 (name "mtd=0", size 100 MiB)
ubi0: PEB size: 262144 bytes (256 KiB), LEB size: 253952 bytes
ubi0: min./max. I/O unit sizes: 4096/4096, sub-page size 4096
ubi0: VID header offset: 4096 (aligned 4096), data offset: 8192
ubi0: good PEBs: 400, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 13/4, WL threshold: 4096, image sequence number: 1831545825
ubi0: available PEBs: 0, total reserved PEBs: 400, PEBs reserved for bad PEB handling: 80
Read 0 bytes from volume kernel to 44000000
No size specified -> Using max size (5332992)
[do_boot_unsignedimg(1004)] mtdids:nand0=nand0
## Loading kernel from FIT Image at 44000000 ...
Using 'config@hk09' configuration
Trying 'kernel@1' kernel subimage
Description: ARM64 OpenWrt Linux-5.4.164
Type: Kernel Image
Compression: gzip compressed
Data Start: 0x440000e8
Data Size: 5149878 Bytes = 4.9 MiB
Architecture: AArch64
OS: Linux
Load Address: 0x41080000
Entry Point: 0x41080000
Hash algo: crc32
Hash value: dc4cdae6
Hash algo: sha1
Hash value: 64b539d6f007c7f44df2fc3abb16d9befe68a20b
Verifying Hash Integrity ... crc32+ sha1+ OK
## Loading fdt from FIT Image at 44000000 ...
Using 'config@hk09' configuration
Trying 'fdt@1' fdt subimage
Description: ARM64 OpenWrt arcadyan_aw1000 device tree blob
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x444e96e0
Data Size: 68060 Bytes = 66.5 KiB
Architecture: AArch64
Hash algo: crc32
Hash value: 6614bdc9
Hash algo: sha1
Hash value: c35bbae37549de281bb614cdcdfcc391c3e49380
Verifying Hash Integrity ... crc32+ sha1+ OK
Booting using the fdt blob at 0x444e96e0
Uncompressing Kernel Image ... OK
Loading Device Tree to 4a3ec000, end 4a3ff9db ... OK
Could not find PCI in device tree
Using machid 0x8010008 from environment
Starting kernel ...
Jumping to AARCH64 kernel via monitorGeneralnie start tego systemu to właśnie trwa dobre 30s w tym momencie , nie wiem ,czy ten kernel się wypakowywuje , czy jak...
153 2024-03-25 22:37:02 (edytowany przez MiG25 2024-03-25 22:49:16)
Odp: Arcadyan AW1000
Start z pendriva usb Twoją metodą też się powiódł.
Najpierw przygotowujemy na linuxie pendriwe z initramfs :
sudo dd if=openwrt-qualcommax-ipq807x-arcadyan_aw1000-initramfs-uImage.itb bs=1M of=/dev/sdc1Po czym w uboocie po kolei:
usb start
usbboot 0x44000000 0:1
bootm 0x44000000Odp: Arcadyan AW1000
To spróbuj wrzucić na USB obraz (nadpisze się zawartość USB):
dd bs=1M if=openwrt-qualcommax-ipq807x-arcadyan_aw1000-initramfs-uImage.itb of=/dev/sdXNa końcu zmień to X na odpowiednią literę.
A później podłącz USB do routera i odpal:
usb start
usbboot 0x44000000 0
bootm 0x44000000i sprawdź czy system wystartuje. Jak zadziałą to możesz sobie ustawić zmienne:
fw_setenv bootusb 'usb start && usbboot 0x44000000 0 && bootm 0x44000000'
fw_setenv bootcmd 'run bootusb; bootipq'i wtedy będzie zawsze startował z USB jeśli będzie USB z initramfs.
155 2024-03-25 22:48:46 (edytowany przez MiG25 2024-03-26 09:32:54)
Odp: Arcadyan AW1000
No tak , takie bootowanie bezpośrednio z dysku ( bez partycji ) też działa , właśnie to równolegle ćwiczyłem 
Dla potomności z uboota to takie komendy:
setenv bootusb 'usb start && usbboot 0x44000000 0 && bootm 0x44000000'
setenv bootcmd 'run bootusb; bootipq'
saveenvI faktycznie działa start automatyczny z uBoota ,jak jest włożony przygotowany pendrive z initramfs.
156 2024-03-25 22:54:26 (edytowany przez frutis 2024-03-25 22:55:20)
Odp: Arcadyan AW1000
Widzę właśnie
Pytałeś o to skąd startuje to tutaj masz odpowiedź:
bootargs=console=ttyMSM0,115200n8 pcie_dev=RG50 ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashfs rootwaitTa zmienna jest zaszyta w u-boocie, dlatego nie wyświetla się przy wyświetlaniu zmiennych ale można ją nadpisać.
Myślę jeszcze o implementacji dualboot...
A co do bootowania z USB to bez partycji jest bezpieczniej, bo można mieć jakąś dziwną tablicę której uboot nie odczyta...
Odp: Arcadyan AW1000
no fakt , tego przy zwykłym bootipq ( debug 0) nie pokazywał...
Odp: Arcadyan AW1000
secam7 napisał/a:
Polimery napisał/a:frutis napisał/a:A testowaliście na kernelu 6.6?
Tu jest wersja z nowszym kernelem z NSS: https://github.com/AgustinLorenzo/openwrt ale w buildzie póki co konfigurację akurat arcadyana zakomentował, więc są póki co tylko te: https://github.com/AgustinLorenzo/openw … 03-25-1818
Napisałem na forum openwrt i gość obiecał dołączyć nasz router do swojej kompilacji.
I wrzucił: https://github.com/AgustinLorenzo/openw … 03-26-0021 i @MiG25 może bootujac z USB z tego nowego builda sprawdzić czy NSS faktycznie działa na nim z Arcadyanem.
Odp: Arcadyan AW1000
A jak to rozpoznać ? Bo tej initramfs nie ma nawet sterowników do modemu .... ( no ale wystartował )
Odp: Arcadyan AW1000
W logach gdzieś powinno być więcej info że nss ładuje.
Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.
Odp: Arcadyan AW1000
Zobacz lsmod.
Odp: Arcadyan AW1000
Tak wygląda grepowanie po nss w logu:
root@OpenWrt:/# logread |grep nss
Thu Jan 1 00:00:10 1970 kern.info kernel: [ 0.000000] OF: reserved mem: 0x0000000040000000..0x0000000040ffffff (16384 KiB) nomap non-reusable nss@40000000
Thu Jan 1 00:00:10 1970 kern.info kernel: [ 0.000000] OF: reserved mem: 0x000000004b000000..0x0000000050efffff (97280 KiB) nomap non-reusable wcnss@4b000000
Thu Jan 1 00:00:10 1970 kern.alert kernel: [ 7.711988] qca-nss-drv.ko is loaded for symbol link
Thu Jan 1 00:00:10 1970 kern.notice kernel: [ 7.753386] nss_vlan_mgr_init_module[1902]:Module (Build Build Id: 03/25/24, 23:16:39) loaded
Thu Jan 1 00:00:10 1970 kern.warn kernel: [ 7.776675] nss_vxlanmgr_init_module[119]:nss-common not found.
Thu Jan 1 00:00:10 1970 kern.warn kernel: [ 7.792503] nss_wifi_meshmgr_init_module[1974]:NSS common not found.
Thu Jan 1 00:00:10 1970 kern.alert kernel: [ 7.817021] nss_cryptoapi_init[2350]:ffffffc079fc0118: Failed to register nss_cryptoapi
Thu Jan 1 00:00:10 1970 kern.alert kernel: [ 7.934789] nss_cryptoapi_init[2350]:ffffffc07a39d118: Failed to register nss_cryptoapi
Thu Jan 1 00:00:10 1970 kern.warn kernel: [ 7.950997] nss_vxlanmgr_init_module[119]:nss-common not found.
Thu Jan 1 00:00:10 1970 kern.warn kernel: [ 7.967495] nss_wifi_meshmgr_init_module[1974]:NSS common not found.
Thu Jan 1 00:00:10 1970 user.err kernel: [ 7.982032] kmodloader: dependency not loaded qca-nss-wifi-meshmgr
Thu Jan 1 00:00:10 1970 user.err kernel: [ 8.000833] kmodloader: - qca-nss-cfi-cryptoapi - 0
Thu Jan 1 00:00:10 1970 user.err kernel: [ 8.004692] kmodloader: - qca-nss-vxlanmgr - 0
Thu Jan 1 00:00:10 1970 user.err kernel: [ 8.009283] kmodloader: - qca-nss-wifi-meshmgr - 0
Thu Jan 1 00:00:10 1970 daemon.notice procd: /etc/rc.d/S13openssl: Generating engines.cnf
Thu Jan 1 00:00:10 1970 daemon.notice procd: /etc/rc.d/S13openssl: Generating providers.cnf
Thu Jan 1 00:00:11 1970 daemon.notice procd: /etc/rc.d/S26qca-nss-ecm: sysctl: error: 'dev.nss/general/redirect' is an unknown key
Thu Jan 1 00:00:11 1970 daemon.notice procd: /etc/rc.d/S26qca-nss-ecm: net.bridge.bridge-nf-call-arptables = 0
Thu Jan 1 00:00:11 1970 daemon.notice procd: /etc/rc.d/S26qca-nss-ecm: net.bridge.bridge-nf-call-iptables = 0
Thu Jan 1 00:00:11 1970 daemon.notice procd: /etc/rc.d/S26qca-nss-ecm: net.bridge.bridge-nf-call-ip6tables = 0
Thu Jan 1 00:00:12 1970 daemon.notice procd: /etc/rc.d/S71qca-nss-pbuf: find: /sys/kernel/debug/ath11k: No such file or directory
Thu Jan 1 00:00:12 1970 user.notice ath11k_nss: Module parameter '/sys/module/ath11k/parameters/nss_offload' does NOT exist. Skipping applying wifi nss configs
Thu Jan 1 00:00:12 1970 kern.info kernel: [ 12.471420] nss-dp 3a001000.dp1 lan1: entered allmulticast mode
Thu Jan 1 00:00:12 1970 kern.info kernel: [ 12.476833] nss-dp 3a001000.dp1 lan1: entered promiscuous mode
Thu Jan 1 00:00:12 1970 kern.info kernel: [ 12.496803] nss-dp 3a001200.dp2 lan2: entered allmulticast mode
Thu Jan 1 00:00:12 1970 kern.info kernel: [ 12.502098] nss-dp 3a001200.dp2 lan2: entered promiscuous mode
Thu Jan 1 00:00:12 1970 kern.info kernel: [ 12.518830] nss-dp 3a001400.dp3 lan3: entered allmulticast mode
Thu Jan 1 00:00:12 1970 kern.info kernel: [ 12.524197] nss-dp 3a001400.dp3 lan3: entered promiscuous mode
Thu Jan 1 00:00:12 1970 kern.info kernel: [ 12.540905] nss-dp 3a001600.dp4 lan4: entered allmulticast mode
Thu Jan 1 00:00:12 1970 kern.info kernel: [ 12.546422] nss-dp 3a001600.dp4 lan4: entered promiscuous mode
root@OpenWrt:/#Odp: Arcadyan AW1000
root@OpenWrt:/# lsmod
act_gact 12288 0
act_mirred 16384 0
act_skbedit 16384 0
aquantia 24576 0
bonding 126976 5 ecm,qca_nss_pppoe,qca_nss_lag_mgr,qca_nss_bridge_mgr,qca_nss_vlan
cfg80211 331776 1 mac80211
chacha_neon 20480 1 libchacha20poly1305
cls_basic 12288 0
cls_flow 16384 0
cls_fw 16384 0
cls_matchall 16384 0
cls_route 16384 0
cls_u32 20480 0
cmac 12288 0
compat 12288 2 mac80211,cfg80211
crc_ccitt 12288 2 ppp_async,aquantia
crc32c_generic 12288 1
drbg 24576 0
dwc3 45056 0
dwc3_qcom 16384 0
ecm 540672 0
em_u32 12288 0
ext4 446464 0
geniv 12288 1 seqiv
gpio_button_hotplug 16384 0
gre 12288 3 pptp,ip6_gre,ip_gre
hmac 12288 0
hwmon 20480 1 aquantia
ifb 12288 0
ip_gre 24576 0
ip_tables 20480 3 iptable_nat,iptable_mangle,iptable_filter
ip6_gre 28672 0
ip6_tunnel 32768 2 qca_nss_tunipip6,ip6_gre
ipt_REJECT 12288 0
iptable_filter 12288 0
iptable_mangle 12288 0
iptable_nat 12288 0
jbd2 73728 1 ext4
jitterentropy_rng 16384 0
kpp 12288 0
l2tp_ppp 20480 1 ecm
leds_gpio 12288 0
libchacha 12288 1 chacha_neon
libchacha20poly1305 12288 1 wireguard
libcrc32c 12288 1 nf_tables
libcurve25519_generic 36864 1 wireguard
mac80211 634880 0
mbcache 12288 1 ext4
michael_mic 12288 0
nat46 45056 2 ecm,qca_nss_map_t
nf_conncount 16384 1 xt_connlimit
nf_conntrack 86016 20 ecm,xt_connlimit,nf_conncount,xt_state,xt_nat,xt_helper,xt_conntrack,xt_connmark,xt_connbytes,xt_REDIRECT,xt_MASQUERADE,nft_redir,nft_nat,nft_masq,nft_flow_offload,nft_ct,nf_nat_rtsp,nf_nat,nf_flow_table,nf_conntrack_rtsp
nf_conntrack_rtsp 16384 2 nf_nat_rtsp
nf_defrag_ipv4 12288 1 nf_conntrack
nf_defrag_ipv6 16384 2 nf_conntrack,nat46
nf_flow_table 28672 2 nf_flow_table_inet,nft_flow_offload
nf_flow_table_inet 12288 0
nf_log_syslog 16384 0
nf_nat 28672 9 iptable_nat,xt_nat,xt_REDIRECT,xt_MASQUERADE,nft_redir,nft_nat,nft_masq,nft_chain_nat,nf_nat_rtsp
nf_nat_rtsp 12288 0
nf_reject_ipv4 12288 3 nft_reject_ipv4,nft_reject_inet,ipt_REJECT
nf_reject_ipv6 12288 2 nft_reject_ipv6,nft_reject_inet
nf_tables 192512226 nft_fib_inet,nf_flow_table_inet,nft_reject_ipv6,nft_reject_ipv4,nft_reject_inet,nft_reject,nft_redir,nft_quota,nft_numgen,nft_nat,nft_masq,nft_log,nft_limit,nft_hash,nft_flow_offload,nft_fib_ipv6,nft_fib_ipv4,nft_fib,nft_ct,nft_chain_nat
nfnetlink 16384 1 nf_tables
nft_chain_nat 12288 2
nft_ct 16384 6
nft_fib 12288 3 nft_fib_inet,nft_fib_ipv6,nft_fib_ipv4
nft_fib_inet 12288 0
nft_fib_ipv4 12288 1 nft_fib_inet
nft_fib_ipv6 12288 1 nft_fib_inet
nft_flow_offload 12288 0
nft_hash 12288 0
nft_limit 12288 6
nft_log 12288 0
nft_masq 12288 1
nft_nat 12288 0
nft_numgen 12288 0
nft_quota 12288 0
nft_redir 12288 0
nft_reject 12288 3 nft_reject_ipv6,nft_reject_ipv4,nft_reject_inet
nft_reject_inet 12288 2
nft_reject_ipv4 12288 0
nft_reject_ipv6 12288 0
poly1305_neon 16384 1 libchacha20poly1305
ppp_async 16384 0
ppp_generic 36864 9 ecm,ppp_async,l2tp_ppp,qca_nss_pptp,pptp,qca_nss_pppoe,pppoe,pppox,qca_nss_l2tpv2
pppoe 20480 2 ecm,qca_nss_pppoe
pppox 12288 3 l2tp_ppp,pptp,pppoe
pptp 24576 2 ecm,qca_nss_pptp
qca_mcs 53248 1 ecm
qca_nss_bridge_mgr 16384 0
qca_nss_crypto 36864 0
qca_nss_dp 49152 1 qca_nss_drv
qca_nss_drv 929792 14 ecm,mac80211,qca_nss_tunipip6,qca_nss_tun6rd,qca_nss_crypto,qca_nss_qdisc,qca_nss_pptp,qca_nss_pppoe,qca_nss_map_t,qca_nss_lag_mgr,qca_nss_l2tpv2,qca_nss_gre,qca_nss_bridge_mgr,qca_nss_vlan
qca_nss_gre 24576 0
qca_nss_l2tpv2 16384 0
qca_nss_lag_mgr 12288 0
qca_nss_map_t 16384 0
qca_nss_pppoe 12288 0
qca_nss_pptp 12288 0
qca_nss_qdisc 86016 0
qca_nss_tun6rd 12288 0
qca_nss_tunipip6 20480 0
qca_nss_vlan 24576 1 qca_nss_bridge_mgr
qca_ssdk 1110016 5 qca_nss_qdisc,qca_nss_bridge_mgr,qca_nss_vlan,qca_nss_drv,qca_nss_dp
qmi_helpers 20480 0
qrtr 24576 3 qrtr_smd
qrtr_smd 12288 0
sch_hfsc 20480 0
sch_htb 28672 0
sch_ingress 12288 0
sch_tbf 16384 0
seqiv 12288 0
sha1_ce 12288 0
sha2_ce 12288 0
sha256_arm64 20480 1 sha2_ce
sha3_generic 12288 0
sha512_arm64 16384 0
sha512_generic 12288 0
sit 24576 1 qca_nss_tun6rd
slhc 12288 1 ppp_generic
tcp_bbr 16384 11
tls 86016 1 bonding
tun 40960 0
tunnel4 12288 1 sit
tunnel6 12288 1 ip6_tunnel
vxlan 90112 1 ecm
wireguard 65536 0
x_tables 24576 24 xt_connlimit,iptable_nat,xt_state,xt_nat,xt_helper,xt_conntrack,xt_connmark,xt_connbytes,xt_REDIRECT,xt_MASQUERADE,iptable_mangle,iptable_filter,ipt_REJECT,ip_tables,xt_time,xt_tcpudp,xt_recent,xt_multiport,xt_mark,xt_mac,xt_limit,xt_comment,xt_TCPMSS,xt_LOG
xhci_hcd 131072 2 xhci_plat_hcd,xhci_pci
xhci_pci 16384 0
xhci_plat_hcd 12288 0
xt_LOG 12288 0
xt_MASQUERADE 12288 0
xt_REDIRECT 12288 0
xt_TCPMSS 12288 0
xt_comment 12288 0
xt_connbytes 12288 0
xt_connlimit 12288 0
xt_connmark 12288 0
xt_conntrack 12288 0
xt_helper 12288 0
xt_limit 12288 0
xt_mac 12288 0
xt_mark 12288 0
xt_multiport 12288 0
xt_nat 12288 0
xt_recent 16384 0
xt_state 12288 0
xt_tcpudp 12288 0
xt_time 12288 0
root@OpenWrt:/#Odp: Arcadyan AW1000
No to masz załadowane moduły.
Odp: Arcadyan AW1000
Pewnie w tym initramfs nie ma iperf3, ale można powtórzyć moj test i puścić iperf przez lan (1G/2.5G) na wif6.
Ciekawe czy będzie jakaś zmiana.
166 2024-03-26 11:41:44 (edytowany przez MiG25 2024-03-26 11:45:09)
Odp: Arcadyan AW1000
Nie ma też sterowników do wifi ( no albo są ,tylko złe) , także w ogóle plik /etc/config/wireless jest pusty.
EDIT: @Cezary kiedyś pisał , że w initramfs to jak się nie zaznaczy konkretnie sterowników wifi to nie będą dodane , także może to ten przypadek. To w sumie cały bootlog ze startu:
U-Boot 2016.01 (Jan 19 2023 - 14:49:11 +0800)
DRAM: smem ram ptable found: ver: 1 len: 4
1 GiB
NAND: Could not find nand_gpio in dts, using defaults
Not an ONFI device
ONFI probe failed
ID = 2691a398
Vendor = 98
Device = a3
qpic_nand: changing oobsize to 160 from 256 bytes
SF: Unsupported flash IDs: manuf ff, jedec ffff, ext_jedec ffff
ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0)
1024 MiB
MMC: sdhci: Node Not found, skipping initialization
PCI0 is not defined in the device tree
PCI1 is not defined in the device tree
In: serial@78B3000
Out: serial@78B3000
Err: serial@78B3000
machid: 8010008
MMC Device 0 not found
[arc_board_setting]
[serial_register_init]
Hit any key to stop autoboot: 0
starting USB...
USB0: Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus 0 for devices... 2 USB Device(s) found
USB1: Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus 1 for devices... 1 USB Device(s) found
Loading from usb device 0, partition 0: Name: Whole Disk Type: U-Boot
Fit image detected...
FIT description: ARM64 OpenWrt FIT (Flattened Image Tree)
Image 0 (kernel-1)
Description: ARM64 OpenWrt Linux-6.6.22
Type: Kernel Image
Compression: gzip compressed
Data Start: 0x440000e8
Data Size: 19813605 Bytes = 18.9 MiB
Architecture: AArch64
OS: Linux
Load Address: 0x41000000
Entry Point: 0x41000000
Hash algo: crc32
Hash value: f8fab400
Hash algo: sha1
Hash value: c9deee2d5652385d72fdaf025ca2ff2fd0e46c50
Image 1 (fdt-1)
Description: ARM64 OpenWrt arcadyan_aw1000 device tree blob
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x452e5710
Data Size: 45442 Bytes = 44.4 KiB
Architecture: AArch64
Hash algo: crc32
Hash value: 6aff139d
Hash algo: sha1
Hash value: 97865d8db487a7614401fcc86529b51e0a8f6c79
Default Configuration: 'config@hk09'
Configuration 0 (config@hk09)
Description: OpenWrt arcadyan_aw1000
Kernel: kernel-1
FDT: fdt-1
## Loading kernel from FIT Image at 44000000 ...
Using 'config@hk09' configuration
Trying 'kernel-1' kernel subimage
Description: ARM64 OpenWrt Linux-6.6.22
Type: Kernel Image
Compression: gzip compressed
Data Start: 0x440000e8
Data Size: 19813605 Bytes = 18.9 MiB
Architecture: AArch64
OS: Linux
Load Address: 0x41000000
Entry Point: 0x41000000
Hash algo: crc32
Hash value: f8fab400
Hash algo: sha1
Hash value: c9deee2d5652385d72fdaf025ca2ff2fd0e46c50
Verifying Hash Integrity ... crc32+ sha1+ OK
## Loading fdt from FIT Image at 44000000 ...
Using 'config@hk09' configuration
Trying 'fdt-1' fdt subimage
Description: ARM64 OpenWrt arcadyan_aw1000 device tree blob
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x452e5710
Data Size: 45442 Bytes = 44.4 KiB
Architecture: AArch64
Hash algo: crc32
Hash value: 6aff139d
Hash algo: sha1
Hash value: 97865d8db487a7614401fcc86529b51e0a8f6c79
Verifying Hash Integrity ... crc32+ sha1+ OK
Booting using the fdt blob at 0x452e5710
Uncompressing Kernel Image ... OK
Loading Device Tree to 4a3f1000, end 4a3ff181 ... OK
mtdids not defined, no default present
Could not find PCI in device tree
Using machid 0x8010008 from environment
Starting kernel ...
Jumping to AARCH64 kernel via monitor
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[ 0.000000] Linux version 6.6.22 (runner@ax3600) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 13.2.0 r0-998fa9d) 13.2.0, GNU ld (GNU Binutils) 2.40.0) #0 SMP PREEMPT Mon Mar 25 21:19:55 2024
[ 0.000000] Machine model: Arcadyan AW1000
[ 0.000000] OF: reserved mem: 0x0000000040000000..0x0000000040ffffff (16384 KiB) nomap non-reusable nss@40000000
[ 0.000000] OF: reserved mem: 0x000000004a400000..0x000000004a5fffff (2048 KiB) nomap non-reusable tzapp@4a400000
[ 0.000000] OF: reserved mem: 0x000000004a600000..0x000000004a9fffff (4096 KiB) nomap non-reusable bootloader@4a600000
[ 0.000000] OF: reserved mem: 0x000000004aa00000..0x000000004aafffff (1024 KiB) nomap non-reusable sbl@4aa00000
[ 0.000000] OF: reserved mem: 0x000000004ab00000..0x000000004abfffff (1024 KiB) nomap non-reusable smem@4ab00000
[ 0.000000] OF: reserved mem: 0x000000004ac00000..0x000000004affffff (4096 KiB) nomap non-reusable memory@4ac00000
[ 0.000000] OF: reserved mem: 0x000000004b000000..0x0000000050efffff (97280 KiB) nomap non-reusable wcnss@4b000000
[ 0.000000] OF: reserved mem: 0x0000000050f00000..0x0000000050ffffff (1024 KiB) nomap non-reusable q6_etr_dump@50f00000
[ 0.000000] OF: reserved mem: 0x0000000051000000..0x00000000510fffff (1024 KiB) nomap non-reusable m3_dump@51000000
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000040000000-0x000000007fffffff]
[ 0.000000] DMA32 empty
[ 0.000000] Normal empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000040000000-0x0000000040ffffff]
[ 0.000000] node 0: [mem 0x0000000041000000-0x000000004a3fffff]
[ 0.000000] node 0: [mem 0x000000004a400000-0x00000000510fffff]
[ 0.000000] node 0: [mem 0x0000000051100000-0x000000007fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000007fffffff]
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.0 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] psci: SMC Calling Convention v1.0
[ 0.000000] percpu: Embedded 19 pages/cpu s37096 r8192 d32536 u77824
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] alternatives: applying boot alternatives
[ 0.000000] Kernel command line: console=ttyMSM0,115200n8 pcie_dev=RG50 root=/dev/ubiblock0_1 swiotlb=noforce
[ 0.000000] Unknown kernel command line parameters "pcie_dev=RG50", will be passed to user space.
[ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes, linear)
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 258048
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 872652K/1048576K available (7936K kernel code, 890K rwdata, 2404K rodata, 15872K init, 274K bss, 175924K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000] Trampoline variant of Tasks RCU enabled.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 100 jiffies.
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] Root IRQ handler: gic_handle_irq
[ 0.000000] GICv2m: range[mem 0x0b00a000-0x0b00affc], SPI[448:479]
[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[ 0.000000] arch_timer: cp15 and mmio timer(s) running at 19.20MHz (virt/virt).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns
[ 0.000000] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns
[ 0.000120] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=19200)
[ 0.000134] pid_max: default: 32768 minimum: 301
[ 0.005436] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.005451] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.009983] RCU Tasks: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1.
[ 0.010089] RCU Tasks Trace: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1.
[ 0.010313] rcu: Hierarchical SRCU implementation.
[ 0.010318] rcu: Max phase no-delay instances is 400.
[ 0.011289] smp: Bringing up secondary CPUs ...
[ 0.011956] Detected VIPT I-cache on CPU1
[ 0.012063] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[ 0.012836] Detected VIPT I-cache on CPU2
[ 0.012909] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
[ 0.013622] Detected VIPT I-cache on CPU3
[ 0.013692] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
[ 0.013766] smp: Brought up 1 node, 4 CPUs
[ 0.013775] SMP: Total of 4 processors activated.
[ 0.013781] CPU features: detected: 32-bit EL0 Support
[ 0.013786] CPU features: detected: CRC32 instructions
[ 0.013855] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching
[ 0.013863] CPU: All CPU(s) started at EL1
[ 0.013866] alternatives: applying system-wide alternatives
[ 0.025356] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns
[ 0.025383] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[ 0.027139] pinctrl core: initialized pinctrl subsystem
[ 0.029315] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.029924] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations
[ 0.029982] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[ 0.030018] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[ 0.030425] thermal_sys: Registered thermal governor 'step_wise'
[ 0.030481] cpuidle: using governor menu
[ 0.030724] ASID allocator initialised with 65536 entries
[ 0.060841] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4
[ 0.064138] Modules: 25872 pages in range for non-PLT usage
[ 0.064150] Modules: 517392 pages in range for PLT usage
[ 0.068520] SCSI subsystem initialized
[ 0.068745] usbcore: registered new interface driver usbfs
[ 0.068781] usbcore: registered new interface driver hub
[ 0.068819] usbcore: registered new device driver usb
[ 0.069319] qcom_scm: convention: smc arm 64
[ 0.070840] clocksource: Switched to clocksource arch_sys_counter
[ 0.074908] NET: Registered PF_INET protocol family
[ 0.075051] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 0.077752] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes, linear)
[ 0.077817] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.077847] TCP established hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.077935] TCP bind hash table entries: 8192 (order: 6, 262144 bytes, linear)
[ 0.078209] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.078320] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.078359] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.078682] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.078724] PCI: CLS 0 bytes, default 64
[ 0.083214] workingset: timestamp_bits=46 max_order=18 bucket_order=0
[ 0.083784] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.083792] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.090536] qcom-qmp-usb-phy 58000.phy: supply vdda-phy not found, using dummy regulator
[ 0.090730] qcom-qmp-usb-phy 58000.phy: supply vdda-pll not found, using dummy regulator
[ 0.091723] qcom-qmp-usb-phy 78000.phy: supply vdda-phy not found, using dummy regulator
[ 0.091938] qcom-qmp-usb-phy 78000.phy: supply vdda-pll not found, using dummy regulator
[ 0.093182] qcom-qusb2-phy 59000.phy: supply vdd not found, using dummy regulator
[ 0.093320] qcom-qusb2-phy 59000.phy: supply vdda-pll not found, using dummy regulator
[ 0.093366] qcom-qusb2-phy 59000.phy: supply vdda-phy-dpdm not found, using dummy regulator
[ 0.093572] qcom-qusb2-phy 59000.phy: Registered Qcom-QUSB2 phy
[ 0.093919] qcom-qusb2-phy 79000.phy: supply vdd not found, using dummy regulator
[ 0.094072] qcom-qusb2-phy 79000.phy: supply vdda-pll not found, using dummy regulator
[ 0.094116] qcom-qusb2-phy 79000.phy: supply vdda-phy-dpdm not found, using dummy regulator
[ 0.094294] qcom-qusb2-phy 79000.phy: Registered Qcom-QUSB2 phy
[ 0.096902] gpio-export gpio-export: 4 gpio(s) exported
[ 0.104688] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.105905] msm_serial 78b3000.serial: msm_serial: detected port #0
[ 0.105948] msm_serial 78b3000.serial: uartclk = 3686400
[ 0.106329] 78b3000.serial: ttyMSM0 at MMIO 0x78b3000 (irq = 21, base_baud = 230400) is a MSM
[ 0.106363] msm_serial: console setup on port #0
[ 0.106423] printk: console [ttyMSM0] enabled
[ 0.922761] msm_serial: driver initialized
[ 0.932471] loop: module loaded
[ 0.933872] nand: device found, Manufacturer ID: 0x98, Chip ID: 0xa3
[ 0.934429] nand: Toshiba TH58NYG3S0HBAI4 8G 1.8V 8-bit
[ 0.941060] nand: 1024 MiB, SLC, erase size: 256 KiB, page size: 4096, OOB size: 256
[ 1.324047] spmi spmi-0: PMIC arbiter version v2 (0x20010000)
[ 1.480531] i2c_dev: i2c /dev entries driver
[ 1.487559] sdhci: Secure Digital Host Controller Interface driver
[ 1.487604] sdhci: Copyright(c) Pierre Ossman
[ 1.492655] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.498430] remoteproc remoteproc0: releasing cd00000.q6v5_wcss
[ 1.506797] NET: Registered PF_INET6 protocol family
[ 1.509575] Segment Routing with IPv6
[ 1.513713] In-situ OAM (IOAM) with IPv6
[ 1.517296] NET: Registered PF_PACKET protocol family
[ 1.521278] Bridge firewalling registered
[ 1.526272] l2tp_core: L2TP core driver, V2.0
[ 1.530153] l2tp_netlink: L2TP netlink interface
[ 1.534523] 8021q: 802.1Q VLAN Support v1.8
[ 1.573897] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4
[ 1.574241] cpr4_ipq807x_apss_read_fuse_data: apc_corner: speed bin = 0
[ 1.580099] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR fusing revision = 1
[ 1.586675] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR misc fuse value = 0
[ 1.594302] cpr4_ipq807x_apss_read_fuse_data: apc_corner: Voltage boost fuse config = 0 boost = disable
[ 1.601804] cpr3_mem_acc_init: apc: not using memory accelerator regulator
[ 1.610939] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused SVS: open-loop= 704000 uV
[ 1.617887] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused NOM: open-loop= 832000 uV
[ 1.627869] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused TURBO: open-loop= 896000 uV
[ 1.637678] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused STURBO: open-loop= 992000 uV
[ 1.647537] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused SVS: quot[ 7]= 688, quot_offset[ 7]= 0
[ 1.657299] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused NOM: quot[ 7]= 929, quot_offset[ 7]= 240
[ 1.668148] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused TURBO: quot[ 7]=1034, quot_offset[ 7]= 105
[ 1.679087] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused STURBO: quot[ 7]=1201, quot_offset[ 7]= 165
[ 1.690229] cpr3_regulator_init_ctrl: apc: Default CPR mode = closed-loop
[ 1.692789] nand: device found, Manufacturer ID: 0x98, Chip ID: 0xa3
[ 1.707730] nand: Toshiba TH58NYG3S0HBAI4 8G 1.8V 8-bit
[ 1.714146] nand: 1024 MiB, SLC, erase size: 256 KiB, page size: 4096, OOB size: 256
[ 1.738313] 26 qcomsmem partitions found on MTD device qcom_nand.0
[ 1.738361] Creating 26 MTD partitions on "qcom_nand.0":
[ 1.743415] 0x000000000000-0x000000100000 : "0:sbl1"
[ 1.750059] 0x000000100000-0x000000200000 : "0:mibib"
[ 1.754813] 0x000000200000-0x000000280000 : "0:bootconfig"
[ 1.759524] 0x000000280000-0x000000300000 : "0:bootconfig1"
[ 1.764980] 0x000000300000-0x000000600000 : "0:qsee"
[ 1.771434] 0x000000600000-0x000000900000 : "0:qsee_1"
[ 1.776672] 0x000000900000-0x000000980000 : "0:devcfg"
[ 1.780555] 0x000000980000-0x000000a00000 : "0:devcfg_1"
[ 1.785676] 0x000000a00000-0x000000a80000 : "0:apdp"
[ 1.791134] 0x000000a80000-0x000000b00000 : "0:apdp_1"
[ 1.796137] 0x000000b00000-0x000000b80000 : "0:rpm"
[ 1.801082] 0x000000b80000-0x000000c00000 : "0:rpm_1"
[ 1.805776] 0x000000c00000-0x000000c80000 : "0:cdt"
[ 1.811037] 0x000000c80000-0x000000d00000 : "0:cdt_1"
[ 1.815709] 0x000000d00000-0x000000d80000 : "0:appsblenv"
[ 1.820939] 0x000000d80000-0x000000e80000 : "0:appsbl"
[ 1.826488] 0x000000e80000-0x000000f80000 : "0:appsbl_1"
[ 1.831586] 0x000000f80000-0x000001000000 : "0:art"
[ 1.836789] 0x000001000000-0x000007400000 : "rootfs"
[ 1.883388] mtd: setting mtd18 (rootfs) as root device
[ 1.883929] mtdsplit: no squashfs found in "rootfs"
[ 1.887484] 0x000007400000-0x000008c80000 : "0:wififw"
[ 1.903189] 0x000008c80000-0x00000f080000 : "rootfs_1"
[ 1.946058] 0x00000f080000-0x000010900000 : "0:wififw_1"
[ 1.957083] 0x000010900000-0x000010b40000 : "0:ethphyfw"
[ 1.958624] 0x000010b40000-0x000010c40000 : "0:board_data"
[ 1.962476] 0x000010c40000-0x000011440000 : "0:arc_datadump"
[ 1.970701] 0x000011440000-0x00003e000000 : "0:arc_data"
[ 2.288856] cpufreq: cpufreq_online: CPU0: Running at unlisted initial frequency: 800000 KHz, changing to: 1017600 KHz
[ 2.290772] remoteproc remoteproc0: cd00000.q6v5_wcss is avail[ 2.309876] Freeing unused kernel memory: 15872K
[ 2.318857] Run /init as init process
[ 2.616925] init: Console is alive
[ 2.617059] init: - watchdog -
[ 2.627691] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 2.642807] gpio_button_hotplug: loading out-of-tree module taints kernel.
[ 2.655568] ssdk_dt_parse_interrupt[916]:INFO:intr-gpio does not exist
[ 3.615908] regi_init[3603]:INFO:Initializing HPPE Done!!
[ 3.616011] regi_init[3662]:INFO:qca-ssdk module init succeeded!
[ 3.622000] EDMA ver 1 hw init
[ 3.626604] EDMA HW Reset completed succesfully
[ 3.629265] Num rings - TxDesc:1 (23-23) TxCmpl:1 (7-7)
[ 3.633737] RxDesc:1 (15-15) RxFill:1 (7-7)
[ 4.038077] **********************************************************
[ 4.038112] * NSS Data Plane driver
[ 4.043500] **********************************************************
[ 4.062105] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 4.062153] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 1
[ 4.066637] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220fe65 hci version 0x110 quirks 0x0000008002000010
[ 4.074082] xhci-hcd xhci-hcd.1.auto: irq 41, io mem 0x08a00000
[ 4.083505] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 4.089322] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 2
[ 4.094880] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed
[ 4.102731] hub 1-0:1.0: USB hub found
[ 4.109044] hub 1-0:1.0: 1 port detected
[ 4.112981] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 4.117159] hub 2-0:1.0: USB hub found
[ 4.124923] hub 2-0:1.0: 1 port detected
[ 4.128801] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller
[ 4.132563] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 3
[ 4.137980] xhci-hcd xhci-hcd.2.auto: hcc params 0x0220fe65 hci version 0x110 quirks 0x0000008002000010
[ 4.145446] xhci-hcd xhci-hcd.2.auto: irq 42, io mem 0x08c00000
[ 4.154865] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller
[ 4.160680] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 4
[ 4.166286] xhci-hcd xhci-hcd.2.auto: Host supports USB 3.0 SuperSpeed
[ 4.174072] hub 3-0:1.0: USB hub found
[ 4.180393] hub 3-0:1.0: 1 port detected
[ 4.184310] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[ 4.188496] hub 4-0:1.0: USB hub found
[ 4.196281] hub 4-0:1.0: 1 port detected
[ 4.201269] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 4.209449] init: - preinit -
[ 4.353851] usb 1-1: new high-speed USB device number 2 using xhci-hcd
[ 4.781842] random: crng init done
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 6.892008] procd: - early -
[ 6.892086] procd: - watchdog -
[ 7.419147] procd: - watchdog -
[ 7.419315] procd: - ubus -
[ 7.472054] procd: - init -
Please press Enter to activate this console.
[ 7.622478] kmodloader: loading kernel modules from /etc/modules.d/*
[ 7.692905] tun: Universal TUN/TAP device driver, 1.6
[ 7.698063] urngd: v1.0.2 started.
[ 7.705037] qca-nss-drv.ko is loaded for symbol link
[ 7.706410] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 7.714129] nat46: module (version 4c5beee236841724219598fabb1edc93d4f08ce5) loaded.
[ 7.716677] gre: GRE over IPv4 demultiplexor driver
[ 7.725170] ip_gre: GRE over IPv4 tunneling driver
[ 7.731498] ip6_gre: GRE over IPv6 tunneling driver
[ 7.739499] QCA multicast snooping installed successfully
[ 7.740723] nss_vlan_mgr_init_module[1902]:Module (Build Build Id: 03/25/24, 23:16:39) loaded
[ 7.748377] PPP generic driver version 2.4.2
[ 7.756080] NET: Registered PF_PPPOX protocol family
[ 7.759690] PPTP driver version 0.8.5
[ 7.764135] nss_vxlanmgr_init_module[119]:nss-common not found.
[ 7.778387] nss_wifi_meshmgr_init_module[1974]:NSS common not found.
[ 7.795676] <NSS-CRYPTO>:module loaded Build_ID - 03/25/24, 23:13:21 SoC=ipq807x
[ 7.795956] <NSS-CRYPTO>:module loaded for symbol link
[ 7.803869] nss_cryptoapi_init[2350]:ffffffc079fb9118: Failed to register nss_cryptoapi
[ 7.824299] GACT probability on
[ 7.825139] Mirror/redirect action on
[ 7.830972] u32 classifier
[ 7.831005] input device check on
[ 7.832718] Actions configured
[ 7.842754] Loading modules backported from Linux version v6.6.15-0-g51f354b815c4
[ 7.842803] Backport generated by backports.git 193becf2
[ 7.850178] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[ 7.861569] NET: Registered PF_QIPCRTR protocol family
[ 7.867639] xt_time: kernel timezone is -0000
[ 7.893106] nf_conntrack_rtsp v0.7 loading
[ 7.896363] nf_nat_rtsp v0.7 loading
[ 7.909699] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information.
[ 7.909738] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
[ 7.924313] nss_cryptoapi_init[2350]:ffffffc07a38f118: Failed to register nss_cryptoapi
[ 7.950000] nss_vxlanmgr_init_module[119]:nss-common not found.
[ 7.966501] nss_wifi_meshmgr_init_module[1974]:NSS common not found.
[ 7.981006] kmodloader: 5 modules could not be probed
[ 7.981050] kmodloader: dependency not loaded qca-nss-wifi-meshmgr
[ 7.985053] kmodloader: - ath11k - 1
[ 7.991116] kmodloader: dependency not loaded ath11k
[ 7.994849] kmodloader: - ath11k_ahb - 1
[ 7.999850] kmodloader: - qca-nss-cfi-cryptoapi - 0
[ 8.003711] kmodloader: - qca-nss-vxlanmgr - 0
[ 8.008302] kmodloader: - qca-nss-wifi-meshmgr - 0
[ 9.849340] ECM init
[ 9.849409] ECM database jhash random seed: 0x1fda7242
[ 9.862902] ECM init complete
[ 10.165979] usb 4-1: new SuperSpeed USB device number 2 using xhci-hcd
[ 13.359192] br-lan: port 1(lan1) entered blocking state
[ 13.359247] br-lan: port 1(lan1) entered disabled state
[ 13.363443] nss-dp 3a001000.dp1 lan1: entered allmulticast mode
[ 13.369160] nss-dp 3a001000.dp1 lan1: entered promiscuous mode
[ 13.384511] br-lan: port 2(lan2) entered blocking state
[ 13.384567] br-lan: port 2(lan2) entered disabled state
[ 13.388654] nss-dp 3a001200.dp2 lan2: entered allmulticast mode
[ 13.394154] nss-dp 3a001200.dp2 lan2: entered promiscuous mode
[ 13.404086] br-lan: port 3(lan3) entered blocking state
[ 13.405668] br-lan: port 3(lan3) entered disabled state
[ 13.410822] nss-dp 3a001400.dp3 lan3: entered allmulticast mode
[ 13.416171] nss-dp 3a001400.dp3 lan3: entered promiscuous mode
[ 13.426152] br-lan: port 4(lan4) entered blocking state
[ 13.427814] br-lan: port 4(lan4) entered disabled state
[ 13.432919] nss-dp 3a001600.dp4 lan4: entered allmulticast mode
[ 13.438291] nss-dp 3a001600.dp4 lan4: entered promiscuous mode
[ 17.889181] platform leds: deferred probe pending
[ 32.735874] l11: disablingOdp: Arcadyan AW1000
Bo to initramfs. Buduje się jeden dla wszystkich urządzeń a w sysupgrade są dopiero dodawane pakiety specyficzne dla urządzenia. A że gość nie zaznaczył ich na stałe to masz taki initramfs a nie inny.
Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.
Odp: Arcadyan AW1000
Można zbudować samodzielnie obraz initramfs ze wszystkimi potrzemnymi modułami.
169 2024-03-26 11:50:04 (edytowany przez MiG25 2024-03-26 11:54:25)
Odp: Arcadyan AW1000
No tak , wpadłem na to...
Najlepszym wyjściem byłoby znalezienie tego "ukrytego env" ,żeby ubi tworzyło nie z partycji rootfs ( ubi.mtd=rootfs ) , a z partycji rootfs_1 (ubi.mtd=rootfs_1) , to wtedy zobaczylibyśmy co jest na tym równoległym , i ew wgrywali tam różne testy...
EDIT: Jest taki coś jak bootcount=0 w env ... Może to liczy ilość nieudanych startów , i za którymś razem to przełączy ?
Odp: Arcadyan AW1000
Ustaw na 3 i zobacz.
Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.
Odp: Arcadyan AW1000
Ale żeby wystartować z drugiej partycji wystarczy ustawić:
fw_setenv bootargs console=ttyMSM0,115200n8 pcie_dev=RG50 ubi.mtd=rootfs_1 root=mtd:ubi_rootfs rootfstype=squashfs rootwaitA później usunąć tą zmienną i tyle.
Ten bootcount to chyba nie jest zaimplementowany. Nie ma nic w logach podczas startu.
@MiG25 a zrzut mtd18 i mtd20 zrobisz?
Odp: Arcadyan AW1000
Nic nie dało ...
Odp: Arcadyan AW1000
u-boot musi być zbudowany z odpowiednią opcją: https://github.com/u-boot/u-boot/blob/m … .bootcount
Odp: Arcadyan AW1000
Po wprowadzeniu tego rootfs_1 zrobił się mishmash i się nie uruchomił...
w bootarg zrobiły się dwa te same argumenty , więc nie wiem ,czy on brał w końcu ten ostatni , czy oba....
Tak to wygląda dopuki nie zawisł:
U-Boot 2016.01 (Jan 19 2023 - 14:49:11 +0800)
DRAM: smem ram ptable found: ver: 1 len: 4
1 GiB
NAND: Could not find nand_gpio in dts, using defaults
Not an ONFI device
ONFI probe failed
ID = 2691a398
Vendor = 98
Device = a3
qpic_nand: changing oobsize to 160 from 256 bytes
SF: Unsupported flash IDs: manuf ff, jedec ffff, ext_jedec ffff
ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0)
1024 MiB
MMC: sdhci: Node Not found, skipping initialization
PCI0 is not defined in the device tree
PCI1 is not defined in the device tree
In: serial@78B3000
Out: serial@78B3000
Err: serial@78B3000
machid: 8010008
MMC Device 0 not found
[arc_board_setting]
[serial_register_init]
Hit any key to stop autoboot: 0
starting USB...
USB0: Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus 0 for devices... 1 USB Device(s) found
USB1: Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus 1 for devices... 1 USB Device(s) found
** Bad device usb 0 **
[do_boot_unsignedimg(903)] debug:1
bootargs=console=ttyMSM0,115200n8 pcie_dev=RG50 ubi.mtd=rootfs_1 root=mtd:ubi_rootfs rootfstype=squashfs rootwait ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashfs rootwait
Booting from flash
Using nand device 0
[do_boot_unsignedimg(934)] runcmd:setenv mtdids nand0=nand0 && setenv mtdparts mtdparts=nand0:0x6400000@0x1000000(fs),${msmparts} && ubi part fs && ubi read 0x44000000 kernel &&
ubi0: attaching mtd1
ubi0: scanning is finished
ubi0: attached mtd1 (name "mtd=0", size 100 MiB)
ubi0: PEB size: 262144 bytes (256 KiB), LEB size: 253952 bytes
ubi0: min./max. I/O unit sizes: 4096/4096, sub-page size 4096
ubi0: VID header offset: 4096 (aligned 4096), data offset: 8192
ubi0: good PEBs: 400, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 16/5, WL threshold: 4096, image sequence number: 1831545825
ubi0: available PEBs: 0, total reserved PEBs: 400, PEBs reserved for bad PEB handling: 80
Read 0 bytes from volume kernel to 44000000
No size specified -> Using max size (5332992)
[do_boot_unsignedimg(1004)] mtdids:nand0=nand0
## Loading kernel from FIT Image at 44000000 ...
Using 'config@hk09' configuration
Trying 'kernel@1' kernel subimage
Description: ARM64 OpenWrt Linux-5.4.164
Type: Kernel Image
Compression: gzip compressed
Data Start: 0x440000e8
Data Size: 5149878 Bytes = 4.9 MiB
Architecture: AArch64
OS: Linux
Load Address: 0x41080000
Entry Point: 0x41080000
Hash algo: crc32
Hash value: dc4cdae6
Hash algo: sha1
Hash value: 64b539d6f007c7f44df2fc3abb16d9befe68a20b
Verifying Hash Integrity ... crc32+ sha1+ OK
## Loading fdt from FIT Image at 44000000 ...
Using 'config@hk09' configuration
Trying 'fdt@1' fdt subimage
Description: ARM64 OpenWrt arcadyan_aw1000 device tree blob
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x444e96e0
Data Size: 68060 Bytes = 66.5 KiB
Architecture: AArch64
Hash algo: crc32
Hash value: 6614bdc9
Hash algo: sha1
Hash value: c35bbae37549de281bb614cdcdfcc391c3e49380
Verifying Hash Integrity ... crc32+ sha1+ OK
Booting using the fdt blob at 0x444e96e0
Uncompressing Kernel Image ... OK
Loading Device Tree to 4a3ec000, end 4a3ff9db ... OK
Could not find PCI in device tree
Using machid 0x8010008 from environment
Starting kernel ...
Jumping to AARCH64 kernel via monitor
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[ 0.000000] Linux version 5.4.164 (devenv@ubuntu-build) (gcc version 7.5.0 (OpenWrt GCC 7.5.0 r47273-b4df38cf18)) #0 SMP PREEMPT Sat Aug 5 16:42:02 2023
[ 0.000000] Machine model: Arcadyan AW1000
[ 0.000000] Reserved memory: created DMA memory pool at 0x000000004a300000, size 1 MiB
[ 0.000000] OF: reserved mem: initialized node tzapp_data@4a300000, compatible id shared-dma-pool
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.0 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] psci: SMC Calling Convention v1.0
[ 0.000000] percpu: Embedded 24 pages/cpu s59096 r8192 d31016 u98304
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] CPU features: kernel page table isolation disabled by kernel configuration
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 226296
[ 0.000000] Kernel command line: console=ttyMSM0,115200n8 pcie_dev=RG50 ubi.mtd=rootfs_1 root=mtd:ubi_rootfs rootfstype=squashfs rootwait ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashfs rootwait root=/dev/ubiblock0_1 swiotlb=1 coherent_pool=2M
[ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 889280K/919552K available (7678K kernel code, 492K rwdata, 2356K rodata, 576K init, 413K bss, 30272K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000] Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] GICv2m: range[mem 0x0b00a000-0x0b00affc], SPI[448:479]
[ 0.000000] random: get_random_bytes called from start_kernel+0x320/0x470 with crng_init=0
[ 0.000000] arch_timer: cp15 and mmio timer(s) running at 19.20MHz (virt/virt).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns
[ 0.000004] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns
[ 0.000432] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=192000)
[ 0.000444] pid_max: default: 32768 minimum: 301
[ 0.000555] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.000568] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.001551] ASID allocator initialised with 65536 entries
[ 0.001621] rcu: Hierarchical SRCU implementation.
[ 0.002240] MSM Memory Dump base table set up
[ 0.002259] MSM Memory Dump apps data table set up
[ 0.002400] smp: Bringing up secondary CPUs ...
[ 0.002891] Detected VIPT I-cache on CPU1
[ 0.002943] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[ 0.003457] Detected VIPT I-cache on CPU2
[ 0.003490] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
[ 0.003949] Detected VIPT I-cache on CPU3
[ 0.003979] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
[ 0.004044] smp: Brought up 1 node, 4 CPUs
[ 0.004065] SMP: Total of 4 processors activated.
[ 0.004073] CPU features: detected: 32-bit EL0 Support
[ 0.004079] CPU features: detected: CRC32 instructions
[ 0.004120] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching
[ 0.004128] CPU: All CPU(s) started at EL1
[ 0.004366] alternatives: patching kernel code
[ 0.017120] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.017141] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[ 0.017263] pinctrl core: initialized pinctrl subsystem
[ 0.018041] NET: Registered protocol family 16
[ 0.018689] DMA: preallocated 2048 KiB pool for atomic allocations
[ 0.019113] cpuidle: using governor ladder
[ 0.019136] cpuidle: using governor menu
[ 0.019271] NET: Registered protocol family 42
[ 0.019499] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.035154] spmi spmi-0: PMIC arbiter version v2 (0x20010000)
[ 0.051405] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4
[ 0.051671] qcom,cpr3-npu-regulator a4000.npu-cpr: NPU CPR valid fuse count: 2
[ 0.053126] msm_sps_probe: sps:sps is ready
[ 0.065443] cryptd: max_cpu_qlen set to 1000
[ 0.152207] pps_core: LinuxPPS API ver. 1 registered
[ 0.152215] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.152233] PTP clock support registered
[ 0.152942] Advanced Linux Sound Architecture Driver Initialized.
[ 0.152992] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512
[ 0.153742] clocksource: Switched to clocksource arch_sys_counter
[ 0.154322] thermal_sys: Registered thermal governor 'step_wise'
[ 0.154325] thermal_sys: Registered thermal governor 'user_space'
[ 0.156169] NET: Registered protocol family 2
[ 0.156282] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 0.157021] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes, linear)
[ 0.157047] TCP established hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.157134] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear)
[ 0.157279] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.157360] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.157397] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.157539] NET: Registered protocol family 1
[ 0.157569] PCI: CLS 0 bytes, default 64
[ 0.182597] workingset: timestamp_bits=62 max_order=18 bucket_order=0
[ 0.186779] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.186789] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.207717] qcom-qmp-phy 78000.ssphy: 78000.ssphy supply vdda-phy not found, using dummy regulator
[ 0.207783] qcom-qmp-phy 78000.ssphy: 78000.ssphy supply vdda-pll not found, using dummy regulator
[ 0.208144] qcom-qmp-phy 78000.ssphy: Registered Qcom-QMP phy
[ 0.208283] qcom-qmp-phy 58000.ssphy: 58000.ssphy supply vdda-phy not found, using dummy regulator
[ 0.208332] qcom-qmp-phy 58000.ssphy: 58000.ssphy supply vdda-pll not found, using dummy regulator
[ 0.208583] qcom-qmp-phy 58000.ssphy: Registered Qcom-QMP phy
[ 0.208886] qcom-qmp-phy 84000.phy: Registered Qcom-QMP phy
[ 0.208966] qcom-qmp-phy: probe of 86000.phy failed with error -13
[ 0.209235] qcom-qmp-phy 8e000.phy: Registered Qcom-QMP phy
[ 0.210741] qcom-pcie 20000000.pci: IRQ mdm2ap_e911 not found
[ 0.213794] qcom-pcie 20000000.pci: host bridge /soc/pci@20000000 ranges:
[ 0.213831] qcom-pcie 20000000.pci: IO 0x20200000..0x2020ffff -> 0x20200000
[ 0.213856] qcom-pcie 20000000.pci: MEM 0x20220000..0x2fffffff -> 0x20220000
[ 40.340148] qcom-pcie 20000000.pci: Phy link never came up
[ 40.341707] qcom-pcie 20000000.pci: cannot initialize host
[ 40.341803] qcom-pcie: probe of 20000000.pci failed with error -110
[ 40.342888] bam-dma-engine 704000.dma: num-channels unspecified in dt
[ 40.342898] bam-dma-engine 704000.dma: num-ees unspecified in dt
[ 40.343476] bam-dma-engine 7884000.dma: qcom,controlled-remotely unspecified
[ 40.344901] bam-dma-engine 7984000.dma: qcom,controlled-remotely unspecified
[ 40.345564] msm-dcc b3000.dcc: DCC XPU is not specified
[ 40.345787] msm-dcc b3000.dcc: jiffies_64: 0xffff9a93, cntvct_64: 0x3b769990
[ 40.345800] msm-dcc b3000.dcc: gcnt_hi: 0x00000000(0x(____ptrval____))
[ 40.345810] msm-dcc b3000.dcc: gcnt_lo: 0x3b769b6f(0x(____ptrval____))
[ 40.346160] global timer is null
[ 40.346415] CPU: IPQ8072A, SoC Version: 2.0
[ 40.346422] OEM_ID: 0, PROD_ID: 0
[ 40.346831] msm_rpm_log_probe: OK
[ 40.347043] TZ SMMU State: SMMU Stage2 Enabled
[ 40.347093] TZ Log : Will warn on Access Violation, as paniconaccessviolation is not set
[ 40.347876] pmd9655_s3: supplied by e-smps1-reg
[ 40.348170] pmd9655_s4: supplied by e-smps1-reg
[ 40.348570] pmd9655_ldo11: supplied by e-smps1-reg
[ 40.349045] msm_serial 78b3000.serial: msm_serial: detected port #0
[ 40.349075] msm_serial 78b3000.serial: uartclk = 3686400
[ 40.349124] 78b3000.serial: ttyMSM0 at MMIO 0x78b3000 (irq = 12, base_baud = 230400) is a MSM
[ 40.349146] msm_serial: console setup on port #0
[ 41.122908] printk: console [ttyMSM0] enabled
[ 41.127830] msm_serial: driver initialized
[ 41.132120] random: fast init done
[ 41.136021] random: crng init done
[ 41.141174] brd: module loaded
[ 41.145430] loop: module loaded
[ 41.147012] nand: device found, Manufacturer ID: 0x98, Chip ID: 0xa3
[ 41.148676] nand: Toshiba TH58NYG3S0H 8G 1.8V 8-bit
[ 41.155313] nand: 1024 MiB, SLC, erase size: 256 KiB, page size: 4096, OOB size: 256
[ 41.160012] 26 fixed-partitions partitions found on MTD device qcom_nand.0
[ 41.167873] Creating 26 MTD partitions on "qcom_nand.0":
[ 41.174570] 0x000000000000-0x000000100000 : "0:SBL1"
[ 41.180986] 0x000000100000-0x000000200000 : "0:MIBIB"
[ 41.185908] 0x000000200000-0x000000280000 : "0:BOOTCONFIG"
[ 41.190603] 0x000000280000-0x000000300000 : "0:BOOTCONFIG1"
[ 41.196047] 0x000000300000-0x000000600000 : "0:QSEE"
[ 41.202569] 0x000000600000-0x000000900000 : "0:QSEE_1"
[ 41.207835] 0x000000900000-0x000000980000 : "0:DEVCFG"
[ 41.211621] 0x000000980000-0x000000a00000 : "0:DEVCFG_1"
[ 41.216765] 0x000000a00000-0x000000a80000 : "0:APDP"
[ 41.222223] 0x000000a80000-0x000000b00000 : "0:APDP_1"
[ 41.227171] 0x000000b00000-0x000000b80000 : "0:RPM"
[ 41.232101] 0x000000b80000-0x000000c00000 : "0:RPM_1"
[ 41.236907] 0x000000c00000-0x000000c80000 : "0:CDT"
[ 41.242094] 0x000000c80000-0x000000d00000 : "0:CDT_1"
[ 41.246808] 0x000000d00000-0x000000d80000 : "0:APPSBLENV"
[ 41.252041] 0x000000d80000-0x000000e80000 : "0:APPSBL"
[ 41.257612] 0x000000e80000-0x000000f80000 : "0:APPSBL_1"
[ 41.262641] 0x000000f80000-0x000001000000 : "0:ART"
[ 41.267894] 0x000001000000-0x000007400000 : "rootfs"
[ 41.316202] mtd: device 18 (rootfs) set to be root filesystem
[ 41.316708] mtdsplit: no squashfs found in "rootfs"
[ 41.320926] 0x000007400000-0x000008c80000 : "0:WIFIFW"
[ 41.336890] 0x000008c80000-0x00000f080000 : "rootfs_1"
[ 41.381370] 0x00000f080000-0x000010900000 : "0:WIFIFW_1"
[ 41.392672] 0x000010900000-0x000010b40000 : "0:ETHPHYFW"
[ 41.394204] 0x000010b40000-0x000010c40000 : "0:board_data"
[ 41.398022] 0x000010c40000-0x000011440000 : "0:arc_datadump"
[ 41.406357] 0x000011440000-0x00003e000000 : "0:arc_data"
[ 41.723717] spi_qup 78b8000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64
[ 41.725092] libphy: Fixed MDIO Bus: probed
[ 42.170246] qca-mdio 90000.mdio: Could not find phy-reset-gpio
[ 42.170410] libphy: qca_mdio: probed
[ 42.176740] qca-mdio 90000.mdio: qca-mdio driver was registered
[ 42.178841] i2c /dev entries driver
[ 42.189308] device-mapper: ioctl: 4.41.0-ioctl (2019-09-16) initialised: dm-devel@redhat.com
[ 42.190908] qcom_ice_get_device_tree_data: No vdd-hba-supply regulator, assuming not needed
[ 42.196878] ICE IRQ = 13
[ 42.205245] sdhci: Secure Digital Host Controller Interface driver
[ 42.207656] sdhci: Copyright(c) Pierre Ossman
[ 42.213641] sdhci-pltfm: SDHCI platform and OF driver helper
[ 42.218459]
[ 42.218459] Version Rollback Feature Disabled
[ 42.224943] remoteproc remoteproc0: cd00000.q6v5_wcss is available
[ 42.229742] SPMI VADC - Min ch: 0 Max ch: 15
[ 42.237419] coresight-tmc 6027000.tmc: failed to get flush cti, defer probe
[ 42.240278] coresight-dynamic-funnel 6021000.funnel: Uses obsolete Coresight DT bindings
[ 42.248287] coresight coresight-etm0: CPU0: ETM v4.0 initialized
[ 42.255076] coresight-etm4x 619c000.etm: CPU0: (null) initialized
[ 42.261367] coresight coresight-etm1: CPU1: ETM v4.0 initialized
[ 42.267073] coresight-etm4x 619d000.etm: CPU1: (null) initialized
[ 42.273428] coresight coresight-etm2: CPU2: ETM v4.0 initialized
[ 42.279115] coresight-etm4x 619e000.etm: CPU2: (null) initialized
[ 42.285503] coresight coresight-etm3: CPU3: ETM v4.0 initialized
[ 42.291166] coresight-etm4x 619f000.etm: CPU3: (null) initialized
[ 42.297432] coresight-stm 6002000.stm: coresight-stm : stm_register_device failed, probing deferred
[ 42.303335] OF: graph: no port node found in /soc/cti@6010000
[ 42.312264] OF: graph: no port node found in /soc/cti@6011000
[ 42.318154] OF: graph: no port node found in /soc/cti@6012000
[ 42.323883] OF: graph: no port node found in /soc/cti@6013000
[ 42.329599] OF: graph: no port node found in /soc/cti@6014000
[ 42.335342] OF: graph: no port node found in /soc/cti@6015000
[ 42.341055] OF: graph: no port node found in /soc/cti@6016000
[ 42.346797] OF: graph: no port node found in /soc/cti@6017000
[ 42.352517] OF: graph: no port node found in /soc/cti@6018000
[ 42.358264] OF: graph: no port node found in /soc/cti@6019000
[ 42.363989] OF: graph: no port node found in /soc/cti@601a000
[ 42.369705] OF: graph: no port node found in /soc/cti@601b000
[ 42.375450] OF: graph: no port node found in /soc/cti@601c000
[ 42.381162] OF: graph: no port node found in /soc/cti@601d000
[ 42.386907] OF: graph: no port node found in /soc/cti@601e000
[ 42.392622] OF: graph: no port node found in /soc/cti@601f000
[ 42.398369] OF: graph: no port node found in /soc/cti@6198000
[ 42.404098] OF: graph: no port node found in /soc/cti@6199000
[ 42.409816] OF: graph: no port node found in /soc/cti@619a000
[ 42.415556] OF: graph: no port node found in /soc/cti@619b000
[ 42.421277] OF: graph: no port node found in /soc/cti@610c000
[ 42.427778] OF: graph: no port node found in /soc/hwevent@6101000
[ 42.432575] coresight-hwevent 6101000.hwevent: No csr data
[ 42.438925] OF: graph: no port node found in /soc/csr@6001000
[ 42.444118] coresight-csr 6001000.csr: CSR initialized: coresight-csr
[ 42.452037] NET: Registered protocol family 10
[ 42.456963] Segment Routing with IPv6
[ 42.460658] NET: Registered protocol family 17
[ 42.464410] Bridge firewalling registered
[ 42.468676] 8021q: 802.1Q VLAN Support v1.8
[ 42.488498] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4
[ 42.488748] cpr4_ipq807x_apss_read_fuse_data: apc_corner: speed bin = 0
[ 42.494669] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR fusing revision = 1
[ 42.501214] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR misc fuse value = 0
[ 42.508888] cpr4_ipq807x_apss_read_fuse_data: apc_corner: Voltage boost fuse config = 0 boost = disable
[ 42.516400] cpr3_mem_acc_init: apc: not using memory accelerator regulator
[ 42.525529] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused SVS: open-loop= 704000 uV
[ 42.532468] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused NOM: open-loop= 832000 uV
[ 42.542462] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused TURBO: open-loop= 896000 uV
[ 42.552268] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused STURBO: open-loop= 992000 uV
[ 42.562135] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused SVS: quot[ 7]= 688, quot_offset[ 7]= 0
[ 42.571898] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused NOM: quot[ 7]= 929, quot_offset[ 7]= 240
[ 42.582743] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused TURBO: quot[ 7]=1034, quot_offset[ 7]= 105
[ 42.593678] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused STURBO: quot[ 7]=1201, quot_offset[ 7]= 165
[ 42.604745] cpr3_regulator_init_ctrl: apc: Default CPR mode = closed-loop
[ 42.605419] qcom,cpr3-npu-regulator a4000.npu-cpr: NPU CPR valid fuse count: 2
[ 42.622440] cpr3_mem_acc_init: npu: not using memory accelerator regulator
[ 42.629441] npu_corner: fused NOM: open-loop= 808000 uV
[ 42.636290] npu_corner: fused TURBO: open-loop= 880000 uV
[ 42.642130] npu_corner: fused NOM: open-loop= 808000 uV
[ 42.647748] npu_corner: fused TURBO: open-loop= 880000 uV
[ 42.653400] npu_corner: Normal and Cold condition init done. Default to normal.
[ 42.659660] core: _opp_supported_by_regulators: OPP minuV: 0 maxuV: 0, not supported by regulator
[ 42.666081] cpu cpu0: _opp_add: OPP not supported by regulators (0)
[ 42.675594] cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 800000 KHz
[ 42.681403] cpufreq: cpufreq_online: CPU0: Unlisted initial frequency changed to: 1017600 KHz
[ 42.688759] sps_register_bam_device: sps:BAM 0x0000000006044000 is registered
[ 42.697630] coresight coresight-stm: STM32 initialized
[ 42.704424] ubi0: attaching mtd20
[ 43.085110] ubi0: scanning is finished
[ 43.090616] ubi0: attached mtd20 (name "rootfs_1", size 100 MiB)
[ 43.090635] ubi0: PEB size: 262144 bytes (256 KiB), LEB size: 253952 bytes
[ 43.095682] ubi0: min./max. I/O unit sizes: 4096/4096, sub-page size 4096
[ 43.102360] ubi0: VID header offset: 4096 (aligned 4096), data offset: 8192
[ 43.109222] ubi0: good PEBs: 400, bad PEBs: 0, corrupted PEBs: 0
[ 43.115991] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
[ 43.122239] ubi0: max/mean erase counter: 46/13, WL threshold: 4096, image sequence number: 1488462315
[ 43.129278] ubi0: available PEBs: 0, total reserved PEBs: 400, PEBs reserved for bad PEB handling: 80
[ 43.138573] ubi0: background thread "ubi_bgt0d" started, PID 207
[ 43.138584] ubi1: attaching mtd18
[ 43.531357] ubi1: scanning is finished
[ 43.536817] ubi1: attached mtd18 (name "rootfs", size 100 MiB)
[ 43.536835] ubi1: PEB size: 262144 bytes (256 KiB), LEB size: 253952 bytes
[ 43.541530] ubi1: min./max. I/O unit sizes: 4096/4096, sub-page size 4096
[ 43.548394] ubi1: VID header offset: 4096 (aligned 4096), data offset: 8192
[ 43.555249] ubi1: good PEBs: 400, bad PEBs: 0, corrupted PEBs: 0
[ 43.562014] ubi1: user volume: 3, internal volumes: 1, max. volumes count: 128
[ 43.568270] ubi1: max/mean erase counter: 16/5, WL threshold: 4096, image sequence number: 1831545825
[ 43.575307] ubi1: available PEBs: 0, total reserved PEBs: 400, PEBs reserved for bad PEB handling: 80
[ 43.584600] ubi1: background thread "ubi_bgt1d" started, PID 208
[ 43.594117] block ubiblock1_1: created from ubi1:1(rootfs)
[ 43.599864] hctosys: unable to open rtc device (rtc0)
[ 43.605677] ALSA device list:
[ 43.610272] No soundcards found.
[ 43.613496] Waiting for root device /dev/ubiblock0_1...
[ 74.073756] pmd9655_ldo11: disablingPosty: 151 do 175 z 823
Strony Poprzednia 1 … 5 6 7 8 9 … 33 Następna
Zaloguj się lub zarejestruj by napisać odpowiedź
eko.one.pl → Sprzęt / Hardware → Arcadyan AW1000
Forum oparte o PunBB, wspierane przez Informer Technologies, Inc