Który sterownik dla tego rtl8153 bo coś nie tak?
kmod-realtek-r8152 - 5.15.147+2.17.1-1 - Realtek USB FE/GBE/2.5G RTL8152/RTL8153/RTL8154/RTL8156
kmod-usb-net-rtl8152 - 5.15.147-1 - Kernel module for USB-to-Ethernet Realtek 8152 USB2.0/3.0 convertors
r8152-firmware - 20230804-1 - RealTek RTL8152 firmware
eth1: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc fq_codel master br-lan state DOWN mode DEFAULT group default qlen 1000
link/ether 00:e0:4c:68:37:03 brd ff:ff:ff:ff:ff:ff
[ 669.262301] r8152-cfgselector 1-2: USB disconnect, device number 2
[ 669.274966] r8152 1-2:1.0 eth1: Stop submitting intr, status -143
[ 669.288513] br-lan: port 1(eth1) entered disabled state
[ 669.303690] device eth1 left promiscuous mode
[ 669.312535] br-lan: port 1(eth1) entered disabled state
[ 669.451195] xhci-mtk 1e1c0000.xhci: drop_ep_quirk high-speed ep3in intr, mpkt:2, interval:8/16ms
[ 669.820495] usb 1-2: new high-speed USB device number 3 using xhci-mtk
[ 669.837511] xhci-mtk 1e1c0000.xhci: ERROR: unexpected setup context command completion code 0x11.
[ 669.855399] usb 1-2: hub failed to enable device, error -22
[ 674.200375] usb usb1-port2: Cannot enable. Maybe the USB cable is bad?
[ 674.213692] usb usb1-port2: attempt power cycle
[ 678.660414] usb usb1-port2: Cannot enable. Maybe the USB cable is bad?
[ 683.010331] usb usb1-port2: Cannot enable. Maybe the USB cable is bad?
[ 683.023655] usb usb1-port2: unable to enumerate USB device
[ 851.558729] usb 1-2: new high-speed USB device number 7 using xhci-mtk
[ 851.753100] xhci-mtk 1e1c0000.xhci: drop_ep_quirk high-speed ep3in intr, mpkt:16, interval:8/16ms
[ 851.929193] r8152-cfgselector 1-2: reset high-speed USB device number 7 using xhci-mtk
[ 852.129852] xhci-mtk 1e1c0000.xhci: drop_ep_quirk high-speed ep3in intr, mpkt:2, interval:8/16ms
[ 852.231110] r8152 1-2:1.0 eth1: v2.17.1 (2023/06/13)
[ 852.241240] r8152 1-2:1.0 eth1: This product is covered by one or more of the following patents:
[ 852.241240] US6,570,884, US6,115,776, and US6,327,625.
[ 852.241240]
jak zainstalowałem:
kmod-realtek-r8152 - 5.15.147+2.17.1-1 - Realtek USB FE/GBE/2.5G RTL8152/RTL8153/RTL8154/RTL8156
to mam...
[ 1532.639395] usb 1-2: USB disconnect, device number 2
[ 1532.650491] xhci-mtk 1e1c0000.xhci: drop_ep_quirk high-speed ep3in intr, mpkt:16, interval:8/16ms
[ 1545.111471] usb 1-2: new high-speed USB device number 3 using xhci-mtk
[ 1589.631685] kmodloader: loading kernel modules from /etc/modules.d/*
[ 1589.666365] usbcore: registered new device driver r8152-cfgselector
[ 1589.679925] xhci-mtk 1e1c0000.xhci: drop_ep_quirk high-speed ep3in intr, mpkt:16, interval:8/16ms
[ 1589.705204] xhci-mtk 1e1c0000.xhci: drop_ep_quirk high-speed ep3in intr, mpkt:16, interval:8/16ms
[ 1589.871305] r8152-cfgselector 1-2: reset high-speed USB device number 3 using xhci-mtk
[ 1590.081614] xhci-mtk 1e1c0000.xhci: drop_ep_quirk high-speed ep3in intr, mpkt:2, interval:8/16ms
[ 1590.192829] r8152 1-2:1.0 eth1: v2.17.1 (2023/06/13)
[ 1590.202997] r8152 1-2:1.0 eth1: This product is covered by one or more of the following patents:
[ 1590.202997] US6,570,884, US6,115,776, and US6,327,625.
[ 1590.202997]
[ 1590.234505] usbcore: registered new interface driver r8152
[ 1590.256855] br-lan: port 5(eth1) entered blocking state
[ 1590.267434] br-lan: port 5(eth1) entered disabled state
[ 1590.278505] device eth1 entered promiscuous mode
[ 1590.288490] br-lan: port 5(eth1) entered blocking state
[ 1590.299057] br-lan: port 5(eth1) entered forwarding state
[ 1590.323389] br-lan: port 5(eth1) entered disabled state
[ 1590.355585] kmodloader: done loading kernel modules from /etc/modules.d/*
...ale dalej nie widzi połączenia...
eth1: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc fq_codel master br-lan state DOWN group default qlen 1000
link/ether 00:e0:4c:68:37:03 brd ff:ff:ff:ff:ff:ff
