1 Temat przez Payti (edytowany przez Payti 2024-02-16 12:52:13)

  • Payti
  • Payti
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2012-01-05
  • Posty: 374

Temat: BPi-R3 i wkładka SFP GPON ONT oraz inne wkładki SFP 1Gbps, 2.5Gbps

Cześć,
z modemem LTE się uporałem, nadszedł czas na uruchomienie wkładki SFP GPON ONT w BPI-R3.
Mam wkładkę Nokia G-010S-A 3FE46541AACA GPON ONT SFP
Po włożeniu w port sfp1 na buildzie OpenWrt 23.05-SNAPSHOT r23695-80ef582dee wkładka się zgłasza:

root@Banana_Pi_BPI-R3:~# dmesg | tail
[  676.472206] DW3 : 03 38 80 41
[  676.472206] DW4 : 01 00 01 00
[  676.472206] DW5 : 0f 20 02 00
[ 2119.401648] sfp sfp-2: module removed
[ 2135.882296] sfp sfp-1: module ALCATELLUCENT    3FE46541AA       rev 0001 sn ALCLF95613A7     dc 190327
[ 2135.891791] sfp sfp-1: Unknown/unsupported extended compliance code: 0x20
[ 2186.310727] hwmon hwmon4: temp1_input not attached to any thermal zone
root@Banana_Pi_BPI-R3:~#

i tyle.

ethtool -m eth1

root@Banana_Pi_BPI-R3:~# ethtool -m eth1
Offset          Values
------          ------
0x0000:         03 04 01 00 00 00 02 00 00 00 00 03 20 00 28 ff
0x0010:         00 00 00 00 41 4c 43 41 54 45 4c 4c 55 43 45 4e
0x0020:         54 20 20 20 20 20 20 20 33 46 45 34 36 35 34 31
0x0030:         41 41 20 20 20 20 20 20 30 30 30 31 05 1e ff dc
0x0040:         00 1a 00 00 41 4c 43 4c 46 39 35 36 31 33 41 37
0x0050:         20 20 20 20 31 39 30 33 32 37 20 20 68 f0 05 4f
0x0060:         41 4c 43 41 54 45 4c 20 33 46 45 34 36 35 34 31
0x0070:         41 41 30 31 32 42 56 4c 33 41 38 4a 4e 41 41 97
0x0080:         00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x0090:         00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x00a0:         00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x00b0:         00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x00c0:         00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x00d0:         00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x00e0:         00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x00f0:         00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x0100:         55 00 d8 00 55 00 d8 00 87 5a 76 ca 87 5a 76 ca
0x0110:         4e 20 05 78 4e 20 05 78 7d 00 2b d4 7d 00 2b d4
0x0120:         06 40 00 0f 06 40 00 0f 00 00 00 00 00 00 00 00
0x0130:         00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x0140:         00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x0150:         00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 14
0x0160:         20 d9 80 e7 0b 29 00 00 00 00 00 00 00 00 02 00
0x0170:         01 40 00 00 01 40 00 00 00 00 00 00 00 00 00 18
0x0180:         00 0f fd 0f fe 00 00 00 00 00 00 00 00 00 00 00
0x0190:         00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x01a0:         00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x01b0:         00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x01c0:         00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x01d0:         00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x01e0:         00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x01f0:         00 00 00 00 00 00 00 00 00 00 00 0a 02 00 00 00
root@Banana_Pi_BPI-R3:~#

Odczyt informacji nt portu eth1 - swiatlowód aktualnie nie podłączony

root@Banana_Pi_BPI-R3:~# ethtool eth1
Settings for eth1:
        Supported ports: [ FIBRE ]
        Supported link modes:   2500baseX/Full
                                1000baseX/Full
        Supported pause frame use: Symmetric Receive-only
        Supports auto-negotiation: Yes
        Supported FEC modes: Not reported
        Advertised link modes:  2500baseX/Full
        Advertised pause frame use: Symmetric Receive-only
        Advertised auto-negotiation: Yes
        Advertised FEC modes: Not reported
        Speed: 2500Mb/s
        Duplex: Full
        Port: FIBRE
        PHYAD: 0
        Transceiver: internal
        Auto-negotiation: on
        Current message level: 0x000000ff (255)
                               drv probe link timer ifdown ifup rx_err tx_err
        Link detected: no
root@Banana_Pi_BPI-R3:~#

Wygląda, że brakuje obsługi w kernelu. Taki sam objaw jest też na kernelu 6.1 (build testowy z repo dla @RafalB).

Cezary co myślisz?
Znalazłem tu patcha do tej wkładki -> https://lore.kernel.org/netdev/E1oYBEz- … ux.org.uk/
-> https://lkml.kernel.org/netdev/20191120 … onome.com/
-> https://git.openwrt.org/?p=openwrt/open … 65e6d551c3

Da się dodać do obecnego kernela OpenWRT, choć wydaje mi się, że powinna być backportowana już ... ?

Tu coś znalazłem na podobny problem -> https://lafibre.info/remplacer-sfr/remplacer-ont-sfr/
ale narazie się wczytuję ...

Pozdr,

Banana Pi BPI-R3 + SFP GPON ONT Nokia G-010S-A + LTE FIBOCOM L860-GL-16 (OpenWrt 25.12-SNAPSHOT, kernel 6.12.71)
Xiaomi AX3600 (OpenWrt 25.12-SNAPSHOT, kernel 6.12.71)
Xiaomi AX3000T (OpenWrt 25.12-SNAPSHOT, kernel 6.12.71)
All OpenWRT compilations from ASU by @Cezary

2 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 115,877

Odp: BPi-R3 i wkładka SFP GPON ONT oraz inne wkładki SFP 1Gbps, 2.5Gbps

@RafalB ci coś o tym powie, on walczył z wkładkami.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

3 Odpowiedź przez Payti (edytowany przez Payti 2024-02-08 19:23:54)

  • Payti
  • Payti
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2012-01-05
  • Posty: 374

Odp: BPi-R3 i wkładka SFP GPON ONT oraz inne wkładki SFP 1Gbps, 2.5Gbps

Przejrzałem dokładnie cały jego wątek i jego wkładka 'wstaje' do pracy w logach.
Ta zaś wyrzuci dwa komunikaty i tyle ...
Na tym francuskim forum w OpenWRT niby widoczna ...

[30572.741487] sfp sfp1: module ALCATELLUCENT    3FE46541AA       rev 0001 sn ALCLF84EF976 dc 170418
[30572.750375] sfp sfp1: Unknown/unsupported extended compliance code: 0x20
[30572.757077] Atheros 8031 ethernet mdio-bus:07: SFP interface 1000base-x
[30572.917487] sfp sfp1: module transmit fault indicated
[30590.149662] mtk_soc_eth 1e100000.ethernet sfp: Link is Up - 1Gbps/Full - flow control rx/tx
[30590.158060] IPv6: ADDRCONF(NETDEV_CHANGE): sfp: link becomes ready
[30632.133651] mtk_soc_eth 1e100000.ethernet sfp: Link is Down
[30632.307438] mtk_soc_eth 1e100000.ethernet sfp: PHY [mdio-bus:07] driver [Atheros 8031 ethernet]
[30632.316209] mtk_soc_eth 1e100000.ethernet sfp: configuring for phy/rgmii-rxid link mode
[30632.324761] at803x_config_aneg: fiber
[30633.349816] mtk_soc_eth 1e100000.ethernet sfp: Link is Up - 1Gbps/Full - flow control rx/tx
[30633.358245] IPv6: ADDRCONF(NETDEV_CHANGE): sfp: link becomes ready
[30638.469658] mtk_soc_eth 1e100000.ethernet sfp: Link is Down
[30638.606324] mtk_soc_eth 1e100000.ethernet sfp: PHY [mdio-bus:07] driver [Atheros 8031 ethernet]
[30638.615113] mtk_soc_eth 1e100000.ethernet sfp: configuring for phy/rgmii-rxid link mode

Co jeszcze sprawdzić ? Może sterownika jakiegoś (Atheros 8031) brakuje ?

Banana Pi BPI-R3 + SFP GPON ONT Nokia G-010S-A + LTE FIBOCOM L860-GL-16 (OpenWrt 25.12-SNAPSHOT, kernel 6.12.71)
Xiaomi AX3600 (OpenWrt 25.12-SNAPSHOT, kernel 6.12.71)
Xiaomi AX3000T (OpenWrt 25.12-SNAPSHOT, kernel 6.12.71)
All OpenWRT compilations from ASU by @Cezary

4 Odpowiedź przez RafalB (edytowany przez RafalB 2024-02-08 20:03:01)

  • RafalB
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2011-01-17
  • Posty: 145

Odp: BPi-R3 i wkładka SFP GPON ONT oraz inne wkładki SFP 1Gbps, 2.5Gbps

Jaką masz wersje kernela?

Zainstaluj też ethtool-full, zwykła wersja nie odczytuje poprawnie eepromu z wkładek

Bardzo często musi być podłączony i aktywny światłowód do wkładki, dopiero wówczas jest poprawna rozpoznawana/aktywna - sprawdź taki wariant

5 Odpowiedź przez Payti

  • Payti
  • Payti
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2012-01-05
  • Posty: 374

Odp: BPi-R3 i wkładka SFP GPON ONT oraz inne wkładki SFP 1Gbps, 2.5Gbps

Wersja kernela：5.15.139
ethtool-full zaraz zainstaluję i potestuję wariant ze światłowodem wpiętym jak mówisz ...

Banana Pi BPI-R3 + SFP GPON ONT Nokia G-010S-A + LTE FIBOCOM L860-GL-16 (OpenWrt 25.12-SNAPSHOT, kernel 6.12.71)
Xiaomi AX3600 (OpenWrt 25.12-SNAPSHOT, kernel 6.12.71)
Xiaomi AX3000T (OpenWrt 25.12-SNAPSHOT, kernel 6.12.71)
All OpenWRT compilations from ASU by @Cezary

6 Odpowiedź przez RafalB

  • RafalB
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2011-01-17
  • Posty: 145

Odp: BPi-R3 i wkładka SFP GPON ONT oraz inne wkładki SFP 1Gbps, 2.5Gbps

Snapshota instaluj, natychmiast!

7 Odpowiedź przez Payti (edytowany przez Payti 2024-02-08 20:35:34)

  • Payti
  • Payti
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2012-01-05
  • Posty: 374

Odp: BPi-R3 i wkładka SFP GPON ONT oraz inne wkładki SFP 1Gbps, 2.5Gbps

Mam ostatniego snapshota @Cezarego z 2024-01-06:

Wersja kernela：5.15.139
Model：Bananapi BPI-R3
Architektura：ARMv8 Processor rev 4
Wersja firmware：OpenWrt 23.05-SNAPSHOT r23695-80ef582dee

Banana Pi BPI-R3 + SFP GPON ONT Nokia G-010S-A + LTE FIBOCOM L860-GL-16 (OpenWrt 25.12-SNAPSHOT, kernel 6.12.71)
Xiaomi AX3600 (OpenWrt 25.12-SNAPSHOT, kernel 6.12.71)
Xiaomi AX3000T (OpenWrt 25.12-SNAPSHOT, kernel 6.12.71)
All OpenWRT compilations from ASU by @Cezary

8 Odpowiedź przez RafalB

  • RafalB
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2011-01-17
  • Posty: 145

Odp: BPi-R3 i wkładka SFP GPON ONT oraz inne wkładki SFP 1Gbps, 2.5Gbps

To nie snapshot, masze wersje 23.05 wink ew .skompiluj sam albo użyj obrazu który Cezary kompilował dla mnie, tam jest kernel 6.1

9 Odpowiedź przez Payti (edytowany przez Payti 2024-02-08 21:09:51)

  • Payti
  • Payti
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2012-01-05
  • Posty: 374

Odp: BPi-R3 i wkładka SFP GPON ONT oraz inne wkładki SFP 1Gbps, 2.5Gbps

A o tym mówisz ? -> https://dl.eko.one.pl/test/bananapi-rpi … k/filogic/

Ale jest progres po zainstalowaniu ethtool-full, narazie bez wpiętego światłowodu:

root@Banana_Pi_BPI-R3:~# ethtool eth1
Settings for eth1:
        Supported ports: [ FIBRE ]
        Supported link modes:   2500baseX/Full
                                1000baseX/Full
        Supported pause frame use: Symmetric Receive-only
        Supports auto-negotiation: Yes
        Supported FEC modes: Not reported
        Advertised link modes:  2500baseX/Full
        Advertised pause frame use: Symmetric Receive-only
        Advertised auto-negotiation: Yes
        Advertised FEC modes: Not reported
        Speed: 2500Mb/s
        Duplex: Full
        Auto-negotiation: on
        Port: FIBRE
        PHYAD: 0
        Transceiver: internal
        Current message level: 0x000000ff (255)
                               drv probe link timer ifdown ifup rx_err tx_err
        Link detected: no
root@Banana_Pi_BPI-R3:~# ethtool -m eth1
        Identifier                                : 0x03 (SFP)
        Extended identifier                       : 0x04 (GBIC/SFP defined by 2-wire interface ID)
        Connector                                 : 0x01 (SC)
        Transceiver codes                         : 0x00 0x00 0x00 0x02 0x00 0x00 0x00 0x00 0x20
        Transceiver type                          : Ethernet: 1000BASE-LX
        Transceiver type                          : Extended: 100G SWDM4
        Encoding                                  : 0x03 (NRZ)
        BR, Nominal                               : 3200MBd
        Rate identifier                           : 0x00 (unspecified)
        Length (SMF,km)                           : 40km
        Length (SMF)                              : 25500m
        Length (50um)                             : 0m
        Length (62.5um)                           : 0m
        Length (Copper)                           : 0m
        Length (OM3)                              : 0m
        Laser wavelength                          : 1310nm
        Vendor name                               : ALCATELLUCENT
        Vendor OUI                                : 20:20:20
        Vendor PN                                 : 3FE46541AA
        Vendor rev                                : 0001
        Option values                             : 0x00 0x1a
        Option                                    : RX_LOS implemented
        Option                                    : TX_FAULT implemented
        Option                                    : TX_DISABLE implemented
        BR margin, max                            : 0%
        BR margin, min                            : 0%
        Vendor SN                                 : ALCLF95613A7
        Date code                                 : 190327
        Optical diagnostics support               : Yes
        Laser bias current                        : 8.648 mA
        Laser output power                        : 0.0000 mW / -inf dBm
        Receiver signal average optical power     : 0.0000 mW / -inf dBm
        Module temperature                        : 49.85 degrees C / 121.73 degrees F
        Module voltage                            : 3.2999 V
        Alarm/warning flags implemented           : Yes
        Laser bias current high alarm             : Off
        Laser bias current low alarm              : Off
        Laser bias current high warning           : Off
        Laser bias current low warning            : Off
        Laser output power high alarm             : Off
        Laser output power low alarm              : On
        Laser output power high warning           : Off
        Laser output power low warning            : On
        Module temperature high alarm             : Off
        Module temperature low alarm              : Off
        Module temperature high warning           : Off
        Module temperature low warning            : Off
        Module voltage high alarm                 : Off
        Module voltage low alarm                  : Off
        Module voltage high warning               : Off
        Module voltage low warning                : Off
        Laser rx power high alarm                 : Off
        Laser rx power low alarm                  : On
        Laser rx power high warning               : Off
        Laser rx power low warning                : On
        Laser bias current high alarm threshold   : 40.000 mA
        Laser bias current low alarm threshold    : 2.800 mA
        Laser bias current high warning threshold : 40.000 mA
        Laser bias current low warning threshold  : 2.800 mA
        Laser output power high alarm threshold   : 3.2000 mW / 5.05 dBm
        Laser output power low alarm threshold    : 1.1220 mW / 0.50 dBm
        Laser output power high warning threshold : 3.2000 mW / 5.05 dBm
        Laser output power low warning threshold  : 1.1220 mW / 0.50 dBm
        Module temperature high alarm threshold   : 85.00 degrees C / 185.00 degrees F
        Module temperature low alarm threshold    : -40.00 degrees C / -40.00 degrees F
        Module temperature high warning threshold : 85.00 degrees C / 185.00 degrees F
        Module temperature low warning threshold  : -40.00 degrees C / -40.00 degrees F
        Module voltage high alarm threshold       : 3.4650 V
        Module voltage low alarm threshold        : 3.0410 V
        Module voltage high warning threshold     : 3.4650 V
        Module voltage low warning threshold      : 3.0410 V
        Laser rx power high alarm threshold       : 0.1600 mW / -7.96 dBm
        Laser rx power low alarm threshold        : 0.0015 mW / -28.24 dBm
        Laser rx power high warning threshold     : 0.1600 mW / -7.96 dBm
        Laser rx power low warning threshold      : 0.0015 mW / -28.24 dBm
root@Banana_Pi_BPI-R3:~#

Wkładkę teraz ethtool ładnie zczytał ...

Dodałem interfejs SFP_GPON na nią do /etc/config/network

config interface 'SFP_GPON'
        option proto 'static'
        option device 'eth1'
        option ipaddr '192.168.1.15'
        option netmask '255.255.255.0'

ale jej nie pinguję ... ona ma adres domyślny: 192.168.1.10, w media konwerterze działa ok pod takim ...

Pozdr,

Banana Pi BPI-R3 + SFP GPON ONT Nokia G-010S-A + LTE FIBOCOM L860-GL-16 (OpenWrt 25.12-SNAPSHOT, kernel 6.12.71)
Xiaomi AX3600 (OpenWrt 25.12-SNAPSHOT, kernel 6.12.71)
Xiaomi AX3000T (OpenWrt 25.12-SNAPSHOT, kernel 6.12.71)
All OpenWRT compilations from ASU by @Cezary

10 Odpowiedź przez Payti

  • Payti
  • Payti
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2012-01-05
  • Posty: 374

Odp: BPi-R3 i wkładka SFP GPON ONT oraz inne wkładki SFP 1Gbps, 2.5Gbps

Ok, zainstalowałem na drugiej karcie image z kernelem 6.1 od @Cezarego -> https://dl.eko.one.pl/test/bananapi-rpi … k/filogic/
Wersja kernela：6.1.64
Model：Bananapi BPI-R3
Architektura：ARMv8 Processor rev 4
Wersja firmware：OpenWrt SNAPSHOT r24564-78d259e7d2

Dodałem to repo do customfeed z modułami, doinstalowałem co trzeba ...
Skonfigurowałem j/w w poprzednim interfejs sfp_gpon do wkładki i objaw taki sam, nie pinguje wkładki SFP GPON.
ethtool (full) widzi to samo j/w.
Jutro potestuję oba z wpiętym światłowodem, bo dziś już rodzinka śpi i nie chcę budzić ...

Banana Pi BPI-R3 + SFP GPON ONT Nokia G-010S-A + LTE FIBOCOM L860-GL-16 (OpenWrt 25.12-SNAPSHOT, kernel 6.12.71)
Xiaomi AX3600 (OpenWrt 25.12-SNAPSHOT, kernel 6.12.71)
Xiaomi AX3000T (OpenWrt 25.12-SNAPSHOT, kernel 6.12.71)
All OpenWRT compilations from ASU by @Cezary

11 Odpowiedź przez RafalB

  • RafalB
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2011-01-17
  • Posty: 145

Odp: BPi-R3 i wkładka SFP GPON ONT oraz inne wkładki SFP 1Gbps, 2.5Gbps

Daj sobie luzu z pingowaniem, ja tu odpuściłem, skonfiguruj ja w mediakonwerterze/switchu i wio

12 Odpowiedź przez Payti (edytowany przez Payti 2024-02-09 17:10:10)

  • Payti
  • Payti
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2012-01-05
  • Posty: 374

Odp: BPi-R3 i wkładka SFP GPON ONT oraz inne wkładki SFP 1Gbps, 2.5Gbps

A masz wkładkę dostępną z jakiegoś interfejsu np. sfp_gpon  coby móc coś zobaczyć na niej  jak siedzi w routerze ?
Pokaż proszę loga z dmesg jak wstaje Twoja wkładka jak jest gotowa do pracy i ma link optyczny wpięty.
Oraz prośba o info jak masz dodany interfejs z VLAN i proto na GPON.

Banana Pi BPI-R3 + SFP GPON ONT Nokia G-010S-A + LTE FIBOCOM L860-GL-16 (OpenWrt 25.12-SNAPSHOT, kernel 6.12.71)
Xiaomi AX3600 (OpenWrt 25.12-SNAPSHOT, kernel 6.12.71)
Xiaomi AX3000T (OpenWrt 25.12-SNAPSHOT, kernel 6.12.71)
All OpenWRT compilations from ASU by @Cezary

13 Odpowiedź przez Payti

  • Payti
  • Payti
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2012-01-05
  • Posty: 374

Odp: BPi-R3 i wkładka SFP GPON ONT oraz inne wkładki SFP 1Gbps, 2.5Gbps

Testów ciąg dalszy ...
Teraz z wpiętym światłowodem (ale jeszcze nie skonfigurowana wkładka dla Operatora)

root@Banana_Pi_BPI-R3:~# ethtool eth1
Settings for eth1:
        Supported ports: [ FIBRE ]
        Supported link modes:   2500baseX/Full
                                1000baseX/Full
        Supported pause frame use: Symmetric Receive-only
        Supports auto-negotiation: Yes
        Supported FEC modes: Not reported
        Advertised link modes:  2500baseX/Full
        Advertised pause frame use: Symmetric Receive-only
        Advertised auto-negotiation: Yes
        Advertised FEC modes: Not reported
        Speed: 2500Mb/s
        Duplex: Full
        Auto-negotiation: on
        Port: FIBRE
        PHYAD: 0
        Transceiver: internal
        Current message level: 0x000000ff (255)
                               drv probe link timer ifdown ifup rx_err tx_err
        Link detected: no
root@Banana_Pi_BPI-R3:~# ethtool -m eth1
        Identifier                                : 0x03 (SFP)
        Extended identifier                       : 0x04 (GBIC/SFP defined by 2-wire interface ID)
        Connector                                 : 0x01 (SC)
        Transceiver codes                         : 0x00 0x00 0x00 0x02 0x00 0x00 0x00 0x00 0x20
        Transceiver type                          : Ethernet: 1000BASE-LX
        Transceiver type                          : Extended: 100G SWDM4
        Encoding                                  : 0x03 (NRZ)
        BR, Nominal                               : 3200MBd
        Rate identifier                           : 0x00 (unspecified)
        Length (SMF,km)                           : 40km
        Length (SMF)                              : 25500m
        Length (50um)                             : 0m
        Length (62.5um)                           : 0m
        Length (Copper)                           : 0m
        Length (OM3)                              : 0m
        Laser wavelength                          : 1310nm
        Vendor name                               : ALCATELLUCENT
        Vendor OUI                                : 20:20:20
        Vendor PN                                 : 3FE46541AA
        Vendor rev                                : 0001
        Option values                             : 0x00 0x1a
        Option                                    : RX_LOS implemented
        Option                                    : TX_FAULT implemented
        Option                                    : TX_DISABLE implemented
        BR margin, max                            : 0%
        BR margin, min                            : 0%
        Vendor SN                                 : ALCLF95613A7
        Date code                                 : 190327
        Optical diagnostics support               : Yes
        Laser bias current                        : 9.916 mA
        Laser output power                        : 1.5592 mW / 1.93 dBm
        Receiver signal average optical power     : 0.0057 mW / -22.44 dBm
        Module temperature                        : 50.85 degrees C / 123.53 degrees F
        Module voltage                            : 3.2999 V
        Alarm/warning flags implemented           : Yes
        Laser bias current high alarm             : Off
        Laser bias current low alarm              : Off
        Laser bias current high warning           : Off
        Laser bias current low warning            : Off
        Laser output power high alarm             : Off
        Laser output power low alarm              : Off
        Laser output power high warning           : Off
        Laser output power low warning            : Off
        Module temperature high alarm             : Off
        Module temperature low alarm              : Off
        Module temperature high warning           : Off
        Module temperature low warning            : Off
        Module voltage high alarm                 : Off
        Module voltage low alarm                  : Off
        Module voltage high warning               : Off
        Module voltage low warning                : Off
        Laser rx power high alarm                 : Off
        Laser rx power low alarm                  : Off
        Laser rx power high warning               : Off
        Laser rx power low warning                : Off
        Laser bias current high alarm threshold   : 40.000 mA
        Laser bias current low alarm threshold    : 2.800 mA
        Laser bias current high warning threshold : 40.000 mA
        Laser bias current low warning threshold  : 2.800 mA
        Laser output power high alarm threshold   : 3.2000 mW / 5.05 dBm
        Laser output power low alarm threshold    : 1.1220 mW / 0.50 dBm
        Laser output power high warning threshold : 3.2000 mW / 5.05 dBm
        Laser output power low warning threshold  : 1.1220 mW / 0.50 dBm
        Module temperature high alarm threshold   : 85.00 degrees C / 185.00 degrees F
        Module temperature low alarm threshold    : -40.00 degrees C / -40.00 degrees F
        Module temperature high warning threshold : 85.00 degrees C / 185.00 degrees F
        Module temperature low warning threshold  : -40.00 degrees C / -40.00 degrees F
        Module voltage high alarm threshold       : 3.4650 V
        Module voltage low alarm threshold        : 3.0410 V
        Module voltage high warning threshold     : 3.4650 V
        Module voltage low warning threshold      : 3.0410 V
        Laser rx power high alarm threshold       : 0.1600 mW / -7.96 dBm
        Laser rx power low alarm threshold        : 0.0015 mW / -28.24 dBm
        Laser rx power high warning threshold     : 0.1600 mW / -7.96 dBm
        Laser rx power low warning threshold      : 0.0015 mW / -28.24 dBm
root@Banana_Pi_BPI-R3:~#
root@Banana_Pi_BPI-R3:~# dmesg | grep eth1
[    1.211933] mtk_soc_eth 15100000.ethernet eth1: mediatek frame engine at 0xffffffc009500000, irq 123
[   20.912268] mtk_soc_eth 15100000.ethernet eth1: configuring for inband/2500base-x link mode
[   20.923565] br-wan: port 1(eth1) entered blocking state
[   20.928843] br-wan: port 1(eth1) entered disabled state
[   20.934391] device eth1 entered promiscuous mode
root@Banana_Pi_BPI-R3:~# dmesg | grep sfp-1
[   13.039436] sfp sfp-1: Host maximum power 3.0W
[   13.388470] sfp sfp-1: module ALCATELLUCENT    3FE46541AA       rev 0001 sn ALCLF95613A7     dc 190327
[   13.397954] sfp sfp-1: Unknown/unsupported extended compliance code: 0x20
root@Banana_Pi_BPI-R3:~#

Sama wkładka działa na kernelu 6.1, ale też nie ma dostępu do niej z ssh i web-gui jak siedzi w routerze. Pobawię się w skonfigurowanie w mediakonwerterze i załadowanie do niej modowanego softu OpenWRT 7.5.3 aby działała z moim dostawcą GPON.
Dam znać jak będzie progres ...

Banana Pi BPI-R3 + SFP GPON ONT Nokia G-010S-A + LTE FIBOCOM L860-GL-16 (OpenWrt 25.12-SNAPSHOT, kernel 6.12.71)
Xiaomi AX3600 (OpenWrt 25.12-SNAPSHOT, kernel 6.12.71)
Xiaomi AX3000T (OpenWrt 25.12-SNAPSHOT, kernel 6.12.71)
All OpenWRT compilations from ASU by @Cezary

14 Odpowiedź przez RafalB

  • RafalB
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2011-01-17
  • Posty: 145

Odp: BPi-R3 i wkładka SFP GPON ONT oraz inne wkładki SFP 1Gbps, 2.5Gbps

Przy swoich zabawach z Leoxem, zauważyłem że wkładka długo się podnosi i konieczeny jest restart sieci, do tego wkładka a raczej samo openwrt w bananapi nie lubi autonegocjacji. Zerknij na mój wątek dotyczący leoxa, kilka wskazówek które mi pomogły, tam są. Do interfaceu od strony sfp, żeby dostać się do gui nie dostałem się.

15 Odpowiedź przez Payti (edytowany przez Payti 2024-02-16 16:16:08)

  • Payti
  • Payti
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2012-01-05
  • Posty: 374

Odp: BPi-R3 i wkładka SFP GPON ONT oraz inne wkładki SFP 1Gbps, 2.5Gbps

Ok, jestem po testach na kernelu 6.1.64 kompilacji @Cezarego. Wkładka SFP Nokia G-010S-A 3FE46541AACA GPON ONT  działa OK, analogicznie jak Leox u @RafalB. Jednakże aby tak było w OpenWRT w BPI-R3 trzeba używać oryginalnego firmware we wkładce - ja używam FW -> 3FE46398BFGB18 w banku image1. ethtool wówczas raportuje wszysko poprawnie. Działa ok, prędkości max jakie daje provider bez problemów (1Gbps/100Mbps u mnie).
Jeśli włączymy we wkładce konsolę na uart asc0 (fw_setenv bootdelay 5; fw_setenv asc0 0; fw_setenv preboot) to kończy transmisję do OS OpenWRT i nie widać nic po włożeniu/wyjęciu wkładki w BPI-R3 w dmesg i nie działa poprawnie. Aby to naprawić trzeba przywrócić z backup partycję mtd1 (uboot_env), warto też przed zmianami zrobić sobie backup wszystkich partycji.  Załadowałem też modowane softy OpenWRT 7.5.3. Działają bardzo dobrze w media konwerterze i switchu z L3 ale w OpenWRT BPI-R3 wkładka nie podnosi interfejsu i nie działa. No i u mnie przepisał ten modowany soft EEPROM'a wkładki (musiałem go przywracać z backup .bin), po włożeniu wkładki z tym softem do BPI-R3 zgłaszała w dmesg: 'EEPROM checksum error' - także nie polecam do BPI-R3 tego modowanego softu OpenWRT 7.5.3, choć ma wszystkie opcje do ustawiania GPON i współpracy z OLT w Web-GUI (LuCi) łącznie z VLAN. W switchu i media konweterze wkładka z tym modowanym softem działa super (łatwa konfiguracja).

Podsumowując Nokia G-010S-A 3FE46541AACA z FW: 3FE46398BFGB18 działa dobrze w BPI-R3, po ok 70 sekundach od włączenia zasilania interfejs eth1 dostaje IP i podnosi link. Do Web-GUI i SSH wkładki podobnie jak w Leox nie ma dostępu z poziomu BPI-R3 (trzeba ją skonfigurować wcześniej w media konwerterze lub switchu z komend z konsoli wg -> https://hack-gpon.org/ont-nokia-g-010s-a/ i przełożyć do BPI-R3, nie ma tu problemów bo to się robi raz). W BPI-R3 później konfigurujemy VLAN i eth1 (br-wan) zależnie od tego jaką mamy autoryzację u dostawcy FTTH/GPON.

Banana Pi BPI-R3 + SFP GPON ONT Nokia G-010S-A + LTE FIBOCOM L860-GL-16 (OpenWrt 25.12-SNAPSHOT, kernel 6.12.71)
Xiaomi AX3600 (OpenWrt 25.12-SNAPSHOT, kernel 6.12.71)
Xiaomi AX3000T (OpenWrt 25.12-SNAPSHOT, kernel 6.12.71)
All OpenWRT compilations from ASU by @Cezary

16 Odpowiedź przez RafalB

  • RafalB
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2011-01-17
  • Posty: 145

Odp: BPi-R3 i wkładka SFP GPON ONT oraz inne wkładki SFP 1Gbps, 2.5Gbps

Sprawdź proszę ostatniego snapszota, wczoraj wjechało sporo poprawek i może w tej kwestii coś się zmieniło

17 Odpowiedź przez Payti

  • Payti
  • Payti
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2012-01-05
  • Posty: 374

Odp: BPi-R3 i wkładka SFP GPON ONT oraz inne wkładki SFP 1Gbps, 2.5Gbps

Rozumiem,  że masz na myśli ten snapshot z OpenWRT do BPI-R3 - > SNAPSHOT (r25154-f3cbdaec29) 2024-02-15 15:00:33 -> https://downloads.openwrt.org/snapshots … ard.img.gz

Wgram wieczorem na inną kartę SD i potestuję ...

Banana Pi BPI-R3 + SFP GPON ONT Nokia G-010S-A + LTE FIBOCOM L860-GL-16 (OpenWrt 25.12-SNAPSHOT, kernel 6.12.71)
Xiaomi AX3600 (OpenWrt 25.12-SNAPSHOT, kernel 6.12.71)
Xiaomi AX3000T (OpenWrt 25.12-SNAPSHOT, kernel 6.12.71)
All OpenWRT compilations from ASU by @Cezary

18 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 115,877

Odp: BPi-R3 i wkładka SFP GPON ONT oraz inne wkładki SFP 1Gbps, 2.5Gbps

Payti napisał/a:

Rozumiem,  że masz na myśli ten snapshot z OpenWRT do BPI-R3 - > SNAPSHOT (r25154-f3cbdaec29) 2024-02-15 15:00:33 -> https://downloads.openwrt.org/snapshots … ard.img.gz

Wgram wieczorem na inną kartę SD i potestuję ...

Poczekaj jeszcze chwilę, niech builder przebuduje nowe obrazy.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

19 Odpowiedź przez RafalB

  • RafalB
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2011-01-17
  • Posty: 145

Odp: BPi-R3 i wkładka SFP GPON ONT oraz inne wkładki SFP 1Gbps, 2.5Gbps

Użyj tego https://firmware-selector.openwrt.org/? … api_bpi-r3 i jeszcze dodasz sobie potrzebne pakiety na "gotowo"

Tak jak Cezary piszę, poczekaj bo tu jeszcze nie ma aktualnego feedu

20 Odpowiedź przez Payti

  • Payti
  • Payti
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2012-01-05
  • Posty: 374

Odp: BPi-R3 i wkładka SFP GPON ONT oraz inne wkładki SFP 1Gbps, 2.5Gbps

Cezary napisał/a:

Poczekaj jeszcze chwilę, niech builder przebuduje nowe obrazy.

Spoko, rzecz jasna potestuję Twój build wieczorkiem ...
Przy okazji przetestuję potem też gdzieś 12 typów i modeli różnych wkładek SFP dwuwłóknowych (LC/PC) od różnych producentów 1Gbit/s i 2,5Bbit/s co mam dostępne i ich kompatybilność, współpracę z BPI-R3 i wrzucę do tego wątku wyniki ...

Banana Pi BPI-R3 + SFP GPON ONT Nokia G-010S-A + LTE FIBOCOM L860-GL-16 (OpenWrt 25.12-SNAPSHOT, kernel 6.12.71)
Xiaomi AX3600 (OpenWrt 25.12-SNAPSHOT, kernel 6.12.71)
Xiaomi AX3000T (OpenWrt 25.12-SNAPSHOT, kernel 6.12.71)
All OpenWRT compilations from ASU by @Cezary

21 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 115,877

Odp: BPi-R3 i wkładka SFP GPON ONT oraz inne wkładki SFP 1Gbps, 2.5Gbps

Fajnie, będzie dla przyszłych użytkowników.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

22 Odpowiedź przez Payti (edytowany przez Payti 2024-02-17 00:36:41)

  • Payti
  • Payti
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2012-01-05
  • Posty: 374

Odp: BPi-R3 i wkładka SFP GPON ONT oraz inne wkładki SFP 1Gbps, 2.5Gbps

Ok, skompilowałem ze swoimi pakietami co używam dzisiejszy snapshot:

Wersja kernela：6.1.77
Model：Bananapi BPI-R3
Architektura：ARMv8 Processor rev 4
Wersja firmware：OpenWrt SNAPSHOT r25210-b0b8fd436f

No wszystko bangla bardzo dobrze, modem Fibocom L860-GL ruszył od strzału, wkładka GPON ONT  Nokia G-010S-A 3FE46541AACA z FW: 3FE46398BFGB18 wg opisu powyżej (nie widać jakiejś znaczącej różnicy), także bardzo dobrze.

Zauważalny jest nowy uboot, który się zainstalował 2024.01 i teraz jest tak:

...
[    5.155998] mtk-pcie-gen3 11280000.pcie: host bridge /soc/pcie@11280000 ranges:
[    5.163339] mtk-pcie-gen3 11280000.pcie: Parsing ranges property...
[    5.169613] mtk-pcie-gen3 11280000.pcie:      MEM 0x0020000000..0x002fffffff -> 0x0020000000
[    5.185021] mmc0: host does not support reading read-only switch, assuming write-enable
[    5.196087] mmc0: new high speed SDHC card at address aaaa
[    5.202405] mmcblk0: mmc0:aaaa SD32G 29.7 GiB
[    5.210250] Alternate GPT is invalid, using primary GPT.
[    5.216063]  mmcblk0: p1 p2 p3 p4 p5 p6 p7
[    5.519323] mtk-pcie-gen3 11280000.pcie: PCIe link down, current LTSSM state: detect.quiet (0x1)
[    5.528122] mtk-pcie-gen3: probe of 11280000.pcie failed with error -110
[    5.535883] FIT: Detected U-Boot 2024.01-OpenWrt-r25210-b0b8fd436f
[    5.542062] FIT: Selected configuration: "config-mt7986a-bananapi-bpi-r3" (OpenWrt bananapi_bpi-r3)
[    5.551095] FIT:           kernel sub-image 0x00001000..0x0056d2a0 "kernel-1" (ARM64 OpenWrt Linux-6.1.77)
[    5.560820] FIT:          flat_dt sub-image 0x0056e000..0x00575cda "fdt-1" (ARM64 OpenWrt bananapi_bpi-r3 device tree blob)
[    5.572020] FIT:          flat_dt sub-image 0x00576000..0x005763dd "fdt-mt7986a-bananapi-bpi-r3-emmc" (ARM64 OpenWrt bananapi_bpi-r3 device tree overlay mt7986a-bananapi-bpi-r3-emmc)
[    5.588333] FIT:          flat_dt sub-image 0x00577000..0x0057748f "fdt-mt7986a-bananapi-bpi-r3-nand" (ARM64 OpenWrt bananapi_bpi-r3 device tree overlay mt7986a-bananapi-bpi-r3-nand)
[    5.604647] FIT:          flat_dt sub-image 0x00578000..0x005784bd "fdt-mt7986a-bananapi-bpi-r3-nor" (ARM64 OpenWrt bananapi_bpi-r3 device tree overlay mt7986a-bananapi-bpi-r3-nor)
[    5.620786] FIT:          flat_dt sub-image 0x00579000..0x00579343 "fdt-mt7986a-bananapi-bpi-r3-sd" (ARM64 OpenWrt bananapi_bpi-r3 device tree overlay mt7986a-bananapi-bpi-r3-sd)
[    5.636753] FIT:          flat_dt sub-image 0x0057a000..0x0057a555 "fdt-mt7986a-bananapi-bpi-r3-respeaker-2mics" (ARM64 OpenWrt bananapi_bpi-r3 device tree overlay mt7986a-bananapi-bpi-r3-respeaker-2mics)
[    5.654971] FIT:       filesystem sub-image 0x0057b000..0x010cffff "rootfs-1" (ARM64 OpenWrt bananapi_bpi-r3 rootfs)
[    5.665923] block mmcblk0p7: mapped 1 uImage.FIT filesystem sub-image as /dev/fit0
[    5.673722] block mmcblk0p7: mapped remaing space as /dev/fitrw
[    5.701826] mt7530-mdio mdio-bus:1f: configuring for fixed/2500base-x link mode
[    5.710865] mt7530-mdio mdio-bus:1f: Link is Up - 2.5Gbps/Full - flow control rx/tx
...

root@BananaPi_BPi-R3:~# df -h
Filesystem                Size      Used Available Use% Mounted on
/dev/root                11.5M     11.5M         0 100% /rom
tmpfs                   996.2M      2.6M    993.6M   0% /tmp
/dev/fitrw               76.2M      1.7M     68.4M   2% /overlay
overlayfs:/overlay       76.2M      1.7M     68.4M   2% /
tmpfs                   512.0K         0    512.0K   0% /dev
root@BananaPi_BPi-R3:~# cat /proc/mtd
dev:    size   erasesize  name
mtd0: 07e00000 00020000 "ubi"
mtd1: 00200000 00020000 "bl2"
root@BananaPi_BPi-R3:~#

Na plus wydaje mi się, że szybciej sią płytka BPI-R3 bootuje z SD ...

Pozdr,

Banana Pi BPI-R3 + SFP GPON ONT Nokia G-010S-A + LTE FIBOCOM L860-GL-16 (OpenWrt 25.12-SNAPSHOT, kernel 6.12.71)
Xiaomi AX3600 (OpenWrt 25.12-SNAPSHOT, kernel 6.12.71)
Xiaomi AX3000T (OpenWrt 25.12-SNAPSHOT, kernel 6.12.71)
All OpenWRT compilations from ASU by @Cezary

23 Odpowiedź przez Payti (edytowany przez Payti 2024-02-20 20:02:18)

  • Payti
  • Payti
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2012-01-05
  • Posty: 374

Odp: BPi-R3 i wkładka SFP GPON ONT oraz inne wkładki SFP 1Gbps, 2.5Gbps

Obiecane testy różnych wkładek SFP.

Testy obejmują:
uname -a (na jakiej wersji kernela)
ethtool eth1 (jak wkładka konfiguruje interfejs eth porty sfp1 lub sfp2)
ethtool -m eth1 (odczyt parametrów wkładki I2C oraz jeśli dostępne monitorowania DDM)
ping -c 5 -I sfp2 10.0.0.1 (ping na pętli patchcordem, jeśli możliwe)

----------------------------------------------------------------------------------------------------------------------


Wkładki jednowłóknowe SFP GPON ONT - działające z BPi-R3

1.) Nokia G-010S-A 3FE46541AACA - SC/APC

root@OBanana_Pi_BPI-R3:/# uname -a
Linux OpenWrt 6.1.64 #0 SMP Sat Dec  2 20:57:38 2023 aarch64 GNU/Linux

root@Banana_Pi_BPI-R3:~# dmesg | tail
...
[ 2135.882296] sfp sfp-1: module ALCATELLUCENT    3FE46541AA       rev 0001 sn ALCLF95613A7     dc 190327
[ 2135.891791] sfp sfp-1: Unknown/unsupported extended compliance code: 0x20
[ 2186.310727] hwmon hwmon4: temp1_input not attached to any thermal zone
root@Banana_Pi_BPI-R3:~#

root@Banana_Pi_BPI-R3:~# ethtool eth1
Settings for eth1:
        Supported ports: [ FIBRE ]
        Supported link modes:   2500baseX/Full
                                1000baseX/Full
        Supported pause frame use: Symmetric Receive-only
        Supports auto-negotiation: Yes
        Supported FEC modes: Not reported
        Advertised link modes:  2500baseX/Full
        Advertised pause frame use: Symmetric Receive-only
        Advertised auto-negotiation: Yes
        Advertised FEC modes: Not reported
        Speed: 2500Mb/s
        Duplex: Full
        Auto-negotiation: on
        Port: FIBRE
        PHYAD: 0
        Transceiver: internal
        Current message level: 0x000000ff (255)
                               drv probe link timer ifdown ifup rx_err tx_err
        Link detected: yes
root@Banana_Pi_BPI-R3:~# ethtool -m eth1
        Identifier                                : 0x03 (SFP)
        Extended identifier                       : 0x04 (GBIC/SFP defined by 2-wire interface ID)
        Connector                                 : 0x01 (SC)
        Transceiver codes                         : 0x00 0x00 0x00 0x02 0x00 0x00 0x00 0x00 0x20
        Transceiver type                          : Ethernet: 1000BASE-LX
        Transceiver type                          : Extended: 100G SWDM4
        Encoding                                  : 0x03 (NRZ)
        BR, Nominal                               : 3200MBd
        Rate identifier                           : 0x00 (unspecified)
        Length (SMF,km)                           : 40km
        Length (SMF)                              : 25500m
        Length (50um)                             : 0m
        Length (62.5um)                           : 0m
        Length (Copper)                           : 0m
        Length (OM3)                              : 0m
        Laser wavelength                          : 1310nm
        Vendor name                               : ALCATELLUCENT
        Vendor OUI                                : 20:20:20
        Vendor PN                                 : 3FE46541AA
        Vendor rev                                : 0001
        Option values                             : 0x00 0x1a
        Option                                    : RX_LOS implemented
        Option                                    : TX_FAULT implemented
        Option                                    : TX_DISABLE implemented
        BR margin, max                            : 0%
        BR margin, min                            : 0%
        Vendor SN                                 : ALCLF95613A7
        Date code                                 : 190327
        Optical diagnostics support               : Yes
        Laser bias current                        : 9.916 mA
        Laser output power                        : 1.5592 mW / 1.93 dBm
        Receiver signal average optical power     : 0.0057 mW / -22.44 dBm
        Module temperature                        : 50.85 degrees C / 123.53 degrees F
        Module voltage                            : 3.2999 V
        Alarm/warning flags implemented           : Yes
        Laser bias current high alarm             : Off
        Laser bias current low alarm              : Off
        Laser bias current high warning           : Off
        Laser bias current low warning            : Off
        Laser output power high alarm             : Off
        Laser output power low alarm              : Off
        Laser output power high warning           : Off
        Laser output power low warning            : Off
        Module temperature high alarm             : Off
        Module temperature low alarm              : Off
        Module temperature high warning           : Off
        Module temperature low warning            : Off
        Module voltage high alarm                 : Off
        Module voltage low alarm                  : Off
        Module voltage high warning               : Off
        Module voltage low warning                : Off
        Laser rx power high alarm                 : Off
        Laser rx power low alarm                  : Off
        Laser rx power high warning               : Off
        Laser rx power low warning                : Off
        Laser bias current high alarm threshold   : 40.000 mA
        Laser bias current low alarm threshold    : 2.800 mA
        Laser bias current high warning threshold : 40.000 mA
        Laser bias current low warning threshold  : 2.800 mA
        Laser output power high alarm threshold   : 3.2000 mW / 5.05 dBm
        Laser output power low alarm threshold    : 1.1220 mW / 0.50 dBm
        Laser output power high warning threshold : 3.2000 mW / 5.05 dBm
        Laser output power low warning threshold  : 1.1220 mW / 0.50 dBm
        Module temperature high alarm threshold   : 85.00 degrees C / 185.00 degrees F
        Module temperature low alarm threshold    : -40.00 degrees C / -40.00 degrees F
        Module temperature high warning threshold : 85.00 degrees C / 185.00 degrees F
        Module temperature low warning threshold  : -40.00 degrees C / -40.00 degrees F
        Module voltage high alarm threshold       : 3.4650 V
        Module voltage low alarm threshold        : 3.0410 V
        Module voltage high warning threshold     : 3.4650 V
        Module voltage low warning threshold      : 3.0410 V
        Laser rx power high alarm threshold       : 0.1600 mW / -7.96 dBm
        Laser rx power low alarm threshold        : 0.0015 mW / -28.24 dBm
        Laser rx power high warning threshold     : 0.1600 mW / -7.96 dBm
        Laser rx power low warning threshold      : 0.0015 mW / -28.24 dBm
root@Banana_Pi_BPI-R3:~#

2.) Leox GPON LXT-010S-H - SC/PC - testy i uruchomienie dzięki @RafalB -> https://eko.one.pl/forum/viewtopic.php?id=23477

root@OpenWrt:/# uname -a
Linux OpenWrt 6.1.64 #0 SMP Sat Dec  2 20:57:38 2023 aarch64 GNU/Linux

root@OpenWrt:/# dmesg | tail
[  121.422499] sfp sfp-1: module removed
[  165.951942] sfp sfp-1: module Hisense-Leox     LXT-010S-H       rev 1.0  sn LEOXD10000F7     dc 221104
[  165.961435] mtk_soc_eth 15100000.ethernet eth1: switched to inband/1000base-x link mode
[  166.000919] hwmon hwmon4: temp1_input not attached to any thermal zone

root@OpenWrt:/# ethtool eth1
Settings for eth1:
        Supported ports: [ FIBRE ]
        Supported link modes:   1000baseX/Full
        Supported pause frame use: Symmetric Receive-only
        Supports auto-negotiation: Yes
        Supported FEC modes: Not reported
        Advertised link modes:  1000baseX/Full
        Advertised pause frame use: Symmetric Receive-only
        Advertised auto-negotiation: Yes
        Advertised FEC modes: Not reported
        Link partner advertised link modes:  1000baseX/Full
        Link partner advertised pause frame use: Symmetric Receive-only
        Link partner advertised auto-negotiation: Yes
        Link partner advertised FEC modes: Not reported
        Speed: 1000Mb/s
        Duplex: Full
        Auto-negotiation: on
        Port: FIBRE
        PHYAD: 0
        Transceiver: internal
        Current message level: 0x000000ff (255)
                               drv probe link timer ifdown ifup rx_err tx_err
        Link detected: yes

root@OpenWrt:/# ethtool -m eth1
        Identifier                                : 0x03 (SFP)
        Extended identifier                       : 0x04 (GBIC/SFP defined by 2-wire interface ID)
        Connector                                 : 0x01 (SC)
        Transceiver codes                         : 0x00 0x00 0x00 0x02 0x00 0x00 0x00 0x00 0x00
        Transceiver type                          : Ethernet: 1000BASE-LX
        Encoding                                  : 0x03 (NRZ)
        BR, Nominal                               : 1300MBd
        Rate identifier                           : 0x00 (unspecified)
        Length (SMF,km)                           : 20km
        Length (SMF)                              : 20000m
        Length (50um)                             : 0m
        Length (62.5um)                           : 0m
        Length (Copper)                           : 0m
        Length (OM3)                              : 0m
        Laser wavelength                          : 1310nm
        Vendor name                               : Hisense-Leox
        Vendor OUI                                : 00:00:00
        Vendor PN                                 : LXT-010S-H
        Vendor rev                                : 1.0
        Option values                             : 0x00 0x1a
        Option                                    : RX_LOS implemented
        Option                                    : TX_FAULT implemented
        Option                                    : TX_DISABLE implemented
        BR margin, max                            : 0%
        BR margin, min                            : 0%
        Vendor SN                                 : LEOXD10000F7
        Date code                                 : 221104
        Optical diagnostics support               : Yes
        Laser bias current                        : 9.336 mA
        Laser output power                        : 1.8451 mW / 2.66 dBm
        Receiver signal average optical power     : 0.0126 mW / -19.00 dBm
        Module temperature                        : 54.39 degrees C / 129.90 degrees F
        Module voltage                            : 3.3231 V
        Alarm/warning flags implemented           : Yes
        Laser bias current high alarm             : Off
        Laser bias current low alarm              : Off
        Laser bias current high warning           : Off
        Laser bias current low warning            : Off
        Laser output power high alarm             : Off
        Laser output power low alarm              : Off
        Laser output power high warning           : Off
        Laser output power low warning            : Off
        Module temperature high alarm             : Off
        Module temperature low alarm              : Off
        Module temperature high warning           : Off
        Module temperature low warning            : Off
        Module voltage high alarm                 : Off
        Module voltage low alarm                  : Off
        Module voltage high warning               : Off
        Module voltage low warning                : Off
        Laser rx power high alarm                 : Off
        Laser rx power low alarm                  : Off
        Laser rx power high warning               : Off
        Laser rx power low warning                : Off
        Laser bias current high alarm threshold   : 100.000 mA
        Laser bias current low alarm threshold    : 0.000 mA
        Laser bias current high warning threshold : 80.000 mA
        Laser bias current low warning threshold  : 0.000 mA
        Laser output power high alarm threshold   : 3.9811 mW / 6.00 dBm
        Laser output power low alarm threshold    : 0.7943 mW / -1.00 dBm
        Laser output power high warning threshold : 3.1623 mW / 5.00 dBm
        Laser output power low warning threshold  : 1.0000 mW / 0.00 dBm
        Module temperature high alarm threshold   : 110.00 degrees C / 230.00 degrees F
        Module temperature low alarm threshold    : -45.00 degrees C / -49.00 degrees F
        Module temperature high warning threshold : 105.00 degrees C / 221.00 degrees F
        Module temperature low warning threshold  : -40.00 degrees C / -40.00 degrees F
        Module voltage high alarm threshold       : 3.6000 V
        Module voltage low alarm threshold        : 3.0000 V
        Module voltage high warning threshold     : 3.5000 V
        Module voltage low warning threshold      : 3.1000 V
        Laser rx power high alarm threshold       : 0.1995 mW / -7.00 dBm
        Laser rx power low alarm threshold        : 0.0013 mW / -28.86 dBm
        Laser rx power high warning threshold     : 0.1585 mW / -8.00 dBm
        Laser rx power low warning threshold      : 0.0016 mW / -27.96 dBm

Wkładki SFP 2.5Gbps dwuwłóknowe LC/PC - działające z BPi-R3

1. FIBRAIN FTS-R27G-S31L-020D-HU SFP 155MB-2.67GB - 2.67G 1310nm 20km 

root@BananaPi_BPi-R3 /root [#]# uname -a
Linux BananaPi_BPi-R3 6.1.77 #0 SMP Fri Feb 16 13:10:11 2024 aarch64 GNU/Linux

root@BananaPi_BPi-R3 /root [#]# dmesg | tail
...
[11699.270518] sfp sfp-2: module FIBRAIN          FTSR27GS31L020DH rev 3.0  sn HUC23330156      dc 230922
[11699.319608] hwmon hwmon5: temp1_input not attached to any thermal zone
[11749.570175] mt7530-mdio mdio-bus:1f sfp2: Link is Up - 2.5Gbps/Full - flow control off
[11749.578290] br-lan: port 5(sfp2) entered blocking state
[11749.583508] br-lan: port 5(sfp2) entered forwarding state
[11753.039911] br-lan: received packet on sfp2 with own address as source address (addr:a6:bb:0f:ed:50:d6, vlan:0)
[11758.850180] br-lan: received packet on sfp2 with own address as source address (addr:a6:bb:0f:ed:50:d6, vlan:0)
[11758.860346] br-lan: received packet on sfp2 with own address as source address (addr:a6:bb:0f:ed:50:d6, vlan:0)

root@BananaPi_BPi-R3 /root [#]# ethtool sfp2
Settings for sfp2:
        Supported ports: [ FIBRE ]
        Supported link modes:   2500baseX/Full
        Supported pause frame use: Symmetric Receive-only
        Supports auto-negotiation: Yes
        Supported FEC modes: Not reported
        Advertised link modes:  2500baseX/Full
        Advertised pause frame use: Symmetric Receive-only
        Advertised auto-negotiation: Yes
        Advertised FEC modes: Not reported
        Speed: 2500Mb/s
        Duplex: Full
        Auto-negotiation: on
        Port: FIBRE
        PHYAD: 0
        Transceiver: internal
        Supports Wake-on: d
        Wake-on: d
        Link detected: yes
root@BananaPi_BPi-R3 /root [#]# ethtool -m sfp2
        Identifier                                : 0x03 (SFP)
        Extended identifier                       : 0x04 (GBIC/SFP defined by 2-wire interface ID)
        Connector                                 : 0x07 (LC)
        Transceiver codes                         : 0x00 0x12 0x00 0x00 0x22 0x90 0x01 0x00 0x00
        Transceiver type                          : SONET: SONET reach specifier bit 1
        Transceiver type                          : SONET: OC-48, intermediate reach
        Transceiver type                          : FC: intermediate distance (I)
        Transceiver type                          : FC: Longwave laser (LC)
        Transceiver type                          : FC: Electrical intra-enclosure (EL)
        Transceiver type                          : FC: Longwave laser (LL)
        Transceiver type                          : FC: Single Mode (SM)
        Encoding                                  : 0x03 (NRZ)
        BR, Nominal                               : 2500MBd
        Rate identifier                           : 0x00 (unspecified)
        Length (SMF,km)                           : 20km
        Length (SMF)                              : 20000m
        Length (50um)                             : 0m
        Length (62.5um)                           : 0m
        Length (Copper)                           : 0m
        Length (OM3)                              : 0m
        Laser wavelength                          : 1310nm
        Vendor name                               : FIBRAIN
        Vendor OUI                                : 00:1b:c5
        Vendor PN                                 : FTSR27GS31L020DH
        Vendor rev                                : 3.0
        Option values                             : 0x00 0x1a
        Option                                    : RX_LOS implemented
        Option                                    : TX_FAULT implemented
        Option                                    : TX_DISABLE implemented
        BR margin, max                            : 0%
        BR margin, min                            : 0%
        Vendor SN                                 : HUC23330156
        Date code                                 : 230922
        Optical diagnostics support               : Yes
        Laser bias current                        : 17.466 mA
        Laser output power                        : 0.5687 mW / -2.45 dBm
        Receiver signal average optical power     : 0.5766 mW / -2.39 dBm
        Module temperature                        : 55.93 degrees C / 132.68 degrees F
        Module voltage                            : 3.2682 V
        Alarm/warning flags implemented           : Yes
        Laser bias current high alarm             : Off
        Laser bias current low alarm              : Off
        Laser bias current high warning           : Off
        Laser bias current low warning            : Off
        Laser output power high alarm             : Off
        Laser output power low alarm              : Off
        Laser output power high warning           : Off
        Laser output power low warning            : Off
        Module temperature high alarm             : Off
        Module temperature low alarm              : Off
        Module temperature high warning           : Off
        Module temperature low warning            : Off
        Module voltage high alarm                 : Off
        Module voltage low alarm                  : Off
        Module voltage high warning               : Off
        Module voltage low warning                : Off
        Laser rx power high alarm                 : Off
        Laser rx power low alarm                  : Off
        Laser rx power high warning               : Off
        Laser rx power low warning                : Off
        Laser bias current high alarm threshold   : 90.000 mA
        Laser bias current low alarm threshold    : 0.500 mA
        Laser bias current high warning threshold : 80.000 mA
        Laser bias current low warning threshold  : 1.000 mA
        Laser output power high alarm threshold   : 1.2589 mW / 1.00 dBm
        Laser output power low alarm threshold    : 0.2512 mW / -6.00 dBm
        Laser output power high warning threshold : 1.0000 mW / 0.00 dBm
        Laser output power low warning threshold  : 0.3162 mW / -5.00 dBm
        Module temperature high alarm threshold   : 80.00 degrees C / 176.00 degrees F
        Module temperature low alarm threshold    : -10.00 degrees C / 14.00 degrees F
        Module temperature high warning threshold : 75.00 degrees C / 167.00 degrees F
        Module temperature low warning threshold  : -5.00 degrees C / 23.00 degrees F
        Module voltage high alarm threshold       : 3.6000 V
        Module voltage low alarm threshold        : 2.9000 V
        Module voltage high warning threshold     : 3.5000 V
        Module voltage low warning threshold      : 3.0000 V
        Laser rx power high alarm threshold       : 1.5850 mW / 2.00 dBm
        Laser rx power low alarm threshold        : 0.0100 mW / -20.00 dBm
        Laser rx power high warning threshold     : 1.0000 mW / 0.00 dBm
        Laser rx power low warning threshold      : 0.0158 mW / -18.01 dBm
root@BananaPi_BPi-R3 /root [#]#

Wkładki SFP 1Gbps dwuwłóknowe LC/PC - działające z BPi-R3

1. Finisar FTLF1318P2BTL-HW Class 1 21CFR1040.10 - 1.25G-1310nm-20km-SM-eSFP 

root@BananaPi_BPi-R3 /root [#]# uname -a
Linux BananaPi_BPi-R3 6.1.77 #0 SMP Fri Feb 16 13:10:11 2024 aarch64 GNU/Linux

root@BananaPi_BPi-R3 /root [#]# dmesg | tail
[13470.883933] sfp sfp-2: module FINISAR CORP.    FTLF1318P2BTL-HW rev A    sn PR685XQ          dc 140913
[13470.893429] mt7530-mdio mdio-bus:1f sfp2: switched to inband/1000base-x link mode
[13470.933053] hwmon hwmon5: temp1_input not attached to any thermal zone
[13480.225406] mt7530-mdio mdio-bus:1f sfp2: Link is Up - 1Gbps/Full - flow control rx/tx
[13480.233687] br-lan: port 5(sfp2) entered blocking state
[13480.238915] br-lan: port 5(sfp2) entered forwarding state
[13483.631567] br-lan: received packet on sfp2 with own address as source address (addr:a6:bb:0f:ed:50:d6, vlan:0)
[13487.839888] br-lan: received packet on sfp2 with own address as source address (addr:a6:bb:0f:ed:50:d6, vlan:0)
[13487.850041] br-lan: received packet on sfp2 with own address as source address (addr:a6:bb:0f:ed:50:d6, vlan:0)

root@BananaPi_BPi-R3 /root [#]# ethtool sfp2
Settings for sfp2:
        Supported ports: [ FIBRE ]
        Supported link modes:   1000baseX/Full
        Supported pause frame use: Symmetric Receive-only
        Supports auto-negotiation: Yes
        Supported FEC modes: Not reported
        Advertised link modes:  1000baseX/Full
        Advertised pause frame use: Symmetric Receive-only
        Advertised auto-negotiation: Yes
        Advertised FEC modes: Not reported
        Link partner advertised link modes:  1000baseX/Full
        Link partner advertised pause frame use: Symmetric Receive-only
        Link partner advertised auto-negotiation: Yes
        Link partner advertised FEC modes: Not reported
        Speed: 1000Mb/s
        Duplex: Full
        Auto-negotiation: on
        Port: FIBRE
        PHYAD: 0
        Transceiver: internal
        Supports Wake-on: d
        Wake-on: d
        Link detected: yes
root@BananaPi_BPi-R3 /root [#]# ethtool -m sfp2
        Identifier                                : 0x03 (SFP)
        Extended identifier                       : 0x04 (GBIC/SFP defined by 2-wire interface ID)
        Connector                                 : 0x07 (LC)
        Transceiver codes                         : 0x00 0x00 0x00 0x02 0x12 0x10 0x01 0x00 0x00
        Transceiver type                          : Ethernet: 1000BASE-LX
        Transceiver type                          : FC: long distance (L)
        Transceiver type                          : FC: Longwave laser (LC)
        Transceiver type                          : FC: Longwave laser (LL)
        Transceiver type                          : FC: Single Mode (SM)
        Encoding                                  : 0x01 (8B/10B)
        BR, Nominal                               : 1200MBd
        Rate identifier                           : 0x00 (unspecified)
        Length (SMF,km)                           : 10km
        Length (SMF)                              : 10000m
        Length (50um)                             : 0m
        Length (62.5um)                           : 0m
        Length (Copper)                           : 0m
        Length (OM3)                              : 0m
        Laser wavelength                          : 1310nm
        Vendor name                               : FINISAR CORP.
        Vendor OUI                                : 00:90:65
        Vendor PN                                 : FTLF1318P2BTL-HW
        Vendor rev                                : A
        Option values                             : 0x00 0x1a
        Option                                    : RX_LOS implemented
        Option                                    : TX_FAULT implemented
        Option                                    : TX_DISABLE implemented
        BR margin, max                            : 0%
        BR margin, min                            : 0%
        Vendor SN                                 : PR685XQ
        Date code                                 : 140913
        Optical diagnostics support               : Yes
        Laser bias current                        : 9.320 mA
        Laser output power                        : 0.2775 mW / -5.57 dBm
        Receiver signal average optical power     : 0.3060 mW / -5.14 dBm
        Module temperature                        : 51.18 degrees C / 124.13 degrees F
        Module voltage                            : 3.3154 V
        Alarm/warning flags implemented           : Yes
        Laser bias current high alarm             : Off
        Laser bias current low alarm              : Off
        Laser bias current high warning           : Off
        Laser bias current low warning            : Off
        Laser output power high alarm             : Off
        Laser output power low alarm              : Off
        Laser output power high warning           : Off
        Laser output power low warning            : Off
        Module temperature high alarm             : Off
        Module temperature low alarm              : Off
        Module temperature high warning           : Off
        Module temperature low warning            : Off
        Module voltage high alarm                 : Off
        Module voltage low alarm                  : Off
        Module voltage high warning               : Off
        Module voltage low warning                : Off
        Laser rx power high alarm                 : Off
        Laser rx power low alarm                  : Off
        Laser rx power high warning               : Off
        Laser rx power low warning                : Off
        Laser bias current high alarm threshold   : 39.436 mA
        Laser bias current low alarm threshold    : 2.430 mA
        Laser bias current high warning threshold : 29.436 mA
        Laser bias current low warning threshold  : 2.430 mA
        Laser output power high alarm threshold   : 0.6310 mW / -2.00 dBm
        Laser output power low alarm threshold    : 0.0708 mW / -11.50 dBm
        Laser output power high warning threshold : 0.5012 mW / -3.00 dBm
        Laser output power low warning threshold  : 0.1122 mW / -9.50 dBm
        Module temperature high alarm threshold   : 90.00 degrees C / 194.00 degrees F
        Module temperature low alarm threshold    : -45.00 degrees C / -49.00 degrees F
        Module temperature high warning threshold : 85.00 degrees C / 185.00 degrees F
        Module temperature low warning threshold  : -40.00 degrees C / -40.00 degrees F
        Module voltage high alarm threshold       : 3.7000 V
        Module voltage low alarm threshold        : 2.9000 V
        Module voltage high warning threshold     : 3.6000 V
        Module voltage low warning threshold      : 3.0000 V
        Laser rx power high alarm threshold       : 0.5012 mW / -3.00 dBm
        Laser rx power low alarm threshold        : 0.0126 mW / -19.00 dBm
        Laser rx power high warning threshold     : 0.5012 mW / -3.00 dBm
        Laser rx power low warning threshold      : 0.0126 mW / -19.00 dBm
root@BananaPi_BPi-R3 /root [#]#

2. GBC PHOTONICS SF-SM31020D-GP - 1.25G 20km 1310nm DDM

root@BananaPi_BPi-R3 /root [#]# uname -a
Linux BananaPi_BPi-R3 6.1.77 #0 SMP Fri Feb 16 13:10:11 2024 aarch64 GNU/Linux

root@BananaPi_BPi-R3 /root [#]# dmesg | tail
...
[12786.192465] sfp sfp-2: module GBC PHOTONICS    SF-SM31020D-GP   rev A0   sn GPE2002158183    dc 201215
[12786.201962] mt7530-mdio mdio-bus:1f sfp2: switched to inband/1000base-x link mode
[12786.251634] hwmon hwmon5: temp1_input not attached to any thermal zone
[12795.583402] mt7530-mdio mdio-bus:1f sfp2: Link is Up - 1Gbps/Full - flow control rx/tx
[12795.591681] br-lan: port 5(sfp2) entered blocking state
[12795.596903] br-lan: port 5(sfp2) entered forwarding state
[12795.768646] br-lan: received packet on sfp2 with own address as source address (addr:a6:bb:0f:ed:50:d6, vlan:0)
[12795.778820] br-lan: received packet on sfp2 with own address as source address (addr:a6:bb:0f:ed:50:d6, vlan:0)
[12795.788916] br-lan: received packet on sfp2 with own address as source address (addr:a6:bb:0f:ed:50:d6, vlan:0)

root@BananaPi_BPi-R3 /root [#]# ethtool -m sfp2
        Identifier                                : 0x03 (SFP)
        Extended identifier                       : 0x04 (GBIC/SFP defined by 2-wire interface ID)
        Connector                                 : 0x07 (LC)
        Transceiver codes                         : 0x00 0x00 0x00 0x02 0x12 0x00 0x0d 0x01 0x00
        Transceiver type                          : Ethernet: 1000BASE-LX
        Transceiver type                          : FC: long distance (L)
        Transceiver type                          : FC: Longwave laser (LC)
        Transceiver type                          : FC: Multimode, 62.5um (M6)
        Transceiver type                          : FC: Multimode, 50um (M5)
        Transceiver type                          : FC: Single Mode (SM)
        Transceiver type                          : FC: 100 MBytes/sec
        Encoding                                  : 0x01 (8B/10B)
        BR, Nominal                               : 1300MBd
        Rate identifier                           : 0x00 (unspecified)
        Length (SMF,km)                           : 10km
        Length (SMF)                              : 10000m
        Length (50um)                             : 550m
        Length (62.5um)                           : 550m
        Length (Copper)                           : 0m
        Length (OM3)                              : 0m
        Laser wavelength                          : 1310nm
        Vendor name                               : GBC PHOTONICS
        Vendor OUI                                : 00:53:4f
        Vendor PN                                 : SF-SM31020D-GP
        Vendor rev                                : A0
        Option values                             : 0x00 0x1a
        Option                                    : RX_LOS implemented
        Option                                    : TX_FAULT implemented
        Option                                    : TX_DISABLE implemented
        BR margin, max                            : 0%
        BR margin, min                            : 0%
        Vendor SN                                 : GPE2002158183
        Date code                                 : 201215
        Optical diagnostics support               : Yes
        Laser bias current                        : 19.364 mA
        Laser output power                        : 0.2913 mW / -5.36 dBm
        Receiver signal average optical power     : 0.2560 mW / -5.92 dBm
        Module temperature                        : 45.23 degrees C / 113.41 degrees F
        Module voltage                            : 3.3278 V
        Alarm/warning flags implemented           : Yes
        Laser bias current high alarm             : Off
        Laser bias current low alarm              : Off
        Laser bias current high warning           : Off
        Laser bias current low warning            : Off
        Laser output power high alarm             : Off
        Laser output power low alarm              : Off
        Laser output power high warning           : Off
        Laser output power low warning            : Off
        Module temperature high alarm             : Off
        Module temperature low alarm              : Off
        Module temperature high warning           : Off
        Module temperature low warning            : Off
        Module voltage high alarm                 : Off
        Module voltage low alarm                  : Off
        Module voltage high warning               : Off
        Module voltage low warning                : Off
        Laser rx power high alarm                 : Off
        Laser rx power low alarm                  : Off
        Laser rx power high warning               : Off
        Laser rx power low warning                : Off
        Laser bias current high alarm threshold   : 80.000 mA
        Laser bias current low alarm threshold    : 2.000 mA
        Laser bias current high warning threshold : 70.000 mA
        Laser bias current low warning threshold  : 3.000 mA
        Laser output power high alarm threshold   : 0.5012 mW / -3.00 dBm
        Laser output power low alarm threshold    : 0.1585 mW / -8.00 dBm
        Laser output power high warning threshold : 0.4467 mW / -3.50 dBm
        Laser output power low warning threshold  : 0.1778 mW / -7.50 dBm
        Module temperature high alarm threshold   : 110.00 degrees C / 230.00 degrees F
        Module temperature low alarm threshold    : -45.00 degrees C / -49.00 degrees F
        Module temperature high warning threshold : 95.00 degrees C / 203.00 degrees F
        Module temperature low warning threshold  : -42.00 degrees C / -43.60 degrees F
        Module voltage high alarm threshold       : 3.6000 V
        Module voltage low alarm threshold        : 3.0000 V
        Module voltage high warning threshold     : 3.5000 V
        Module voltage low warning threshold      : 3.0500 V
        Laser rx power high alarm threshold       : 0.5012 mW / -3.00 dBm
        Laser rx power low alarm threshold        : 0.0063 mW / -22.01 dBm
        Laser rx power high warning threshold     : 0.4467 mW / -3.50 dBm
        Laser rx power low warning threshold      : 0.0071 mW / -21.49 dBm
root@BananaPi_BPi-R3 /root [#]#

3. NOKIA 3FE26774AA 01 MFGR P/N: APS31123IDL10NK - 1G SFP SM 1310nm 10km I-Temp

root@BananaPi_BPi-R3 /root [#]# uname -a
Linux BananaPi_BPi-R3 6.1.77 #0 SMP Fri Feb 16 13:10:11 2024 aarch64 GNU/Linux

root@BananaPi_BPi-R3 /root [#]# dmesg | tail
...
[13586.197091] sfp sfp-2: module ATOP             APS31123IDL10NK  rev 01   sn ATOPCN21485695   dc 201201
[13586.246117] hwmon hwmon5: temp1_input not attached to any thermal zone
[13595.537283] mt7530-mdio mdio-bus:1f sfp2: Link is Up - 1Gbps/Full - flow control rx/tx
[13595.545559] br-lan: port 5(sfp2) entered blocking state
[13595.550784] br-lan: port 5(sfp2) entered forwarding state
[13605.118860] br-lan: received packet on sfp2 with own address as source address (addr:a6:bb:0f:ed:50:d6, vlan:0)
[13605.129040] br-lan: received packet on sfp2 with own address as source address (addr:a6:bb:0f:ed:50:d6, vlan:0)
[13605.139142] br-lan: received packet on sfp2 with own address as source address (addr:a6:bb:0f:ed:50:d6, vlan:0)

root@BananaPi_BPi-R3 /root [#]# ethtool sfp2
Settings for sfp2:
        Supported ports: [ FIBRE ]
        Supported link modes:   1000baseX/Full
        Supported pause frame use: Symmetric Receive-only
        Supports auto-negotiation: Yes
        Supported FEC modes: Not reported
        Advertised link modes:  1000baseX/Full
        Advertised pause frame use: Symmetric Receive-only
        Advertised auto-negotiation: Yes
        Advertised FEC modes: Not reported
        Link partner advertised link modes:  1000baseX/Full
        Link partner advertised pause frame use: Symmetric Receive-only
        Link partner advertised auto-negotiation: Yes
        Link partner advertised FEC modes: Not reported
        Speed: 1000Mb/s
        Duplex: Full
        Auto-negotiation: on
        Port: FIBRE
        PHYAD: 0
        Transceiver: internal
        Supports Wake-on: d
        Wake-on: d
        Link detected: yes
root@BananaPi_BPi-R3 /root [#]# ethtool -m sfp2
        Identifier                                : 0x03 (SFP)
        Extended identifier                       : 0x04 (GBIC/SFP defined by 2-wire interface ID)
        Connector                                 : 0x07 (LC)
        Transceiver codes                         : 0x00 0x00 0x00 0x02 0x00 0x00 0x00 0x00 0x00
        Transceiver type                          : Ethernet: 1000BASE-LX
        Encoding                                  : 0x01 (8B/10B)
        BR, Nominal                               : 1300MBd
        Rate identifier                           : 0x00 (unspecified)
        Length (SMF,km)                           : 10km
        Length (SMF)                              : 10000m
        Length (50um)                             : 0m
        Length (62.5um)                           : 0m
        Length (Copper)                           : 0m
        Length (OM3)                              : 0m
        Laser wavelength                          : 1310nm
        Vendor name                               : ATOP
        Vendor OUI                                : 00:00:00
        Vendor PN                                 : APS31123IDL10NK
        Vendor rev                                : 01
        Option values                             : 0x00 0x1a
        Option                                    : RX_LOS implemented
        Option                                    : TX_FAULT implemented
        Option                                    : TX_DISABLE implemented
        BR margin, max                            : 0%
        BR margin, min                            : 0%
        Vendor SN                                 : ATOPCN21485695
        Date code                                 : 201201
        Optical diagnostics support               : Yes
        Laser bias current                        : 22.550 mA
        Laser output power                        : 0.2385 mW / -6.23 dBm
        Receiver signal average optical power     : 0.1997 mW / -7.00 dBm
        Module temperature                        : 43.47 degrees C / 110.25 degrees F
        Module voltage                            : 3.2960 V
        Alarm/warning flags implemented           : Yes
        Laser bias current high alarm             : Off
        Laser bias current low alarm              : Off
        Laser bias current high warning           : Off
        Laser bias current low warning            : Off
        Laser output power high alarm             : Off
        Laser output power low alarm              : Off
        Laser output power high warning           : Off
        Laser output power low warning            : Off
        Module temperature high alarm             : Off
        Module temperature low alarm              : Off
        Module temperature high warning           : Off
        Module temperature low warning            : Off
        Module voltage high alarm                 : Off
        Module voltage low alarm                  : Off
        Module voltage high warning               : Off
        Module voltage low warning                : Off
        Laser rx power high alarm                 : Off
        Laser rx power low alarm                  : Off
        Laser rx power high warning               : Off
        Laser rx power low warning                : Off
        Laser bias current high alarm threshold   : 60.000 mA
        Laser bias current low alarm threshold    : 0.000 mA
        Laser bias current high warning threshold : 50.000 mA
        Laser bias current low warning threshold  : 0.000 mA
        Laser output power high alarm threshold   : 0.5012 mW / -3.00 dBm
        Laser output power low alarm threshold    : 0.1259 mW / -9.00 dBm
        Laser output power high warning threshold : 0.4074 mW / -3.90 dBm
        Laser output power low warning threshold  : 0.1549 mW / -8.10 dBm
        Module temperature high alarm threshold   : 85.00 degrees C / 185.00 degrees F
        Module temperature low alarm threshold    : -40.00 degrees C / -40.00 degrees F
        Module temperature high warning threshold : 75.00 degrees C / 167.00 degrees F
        Module temperature low warning threshold  : -30.00 degrees C / -22.00 degrees F
        Module voltage high alarm threshold       : 3.8000 V
        Module voltage low alarm threshold        : 2.7999 V
        Module voltage high warning threshold     : 3.7000 V
        Module voltage low warning threshold      : 2.8999 V
        Laser rx power high alarm threshold       : 0.5012 mW / -3.00 dBm
        Laser rx power low alarm threshold        : 0.0100 mW / -20.00 dBm
        Laser rx power high warning threshold     : 0.3162 mW / -5.00 dBm
        Laser rx power low warning threshold      : 0.0158 mW / -18.01 dBm
root@BananaPi_BPi-R3 /root [#]#

4. HUAWEI RTXM191-400 (466101) Class 1  - 1.25G-1310nm-10km-SM-ESFP

root@BananaPi_BPi-R3 /root [#]# uname -a
Linux BananaPi_BPi-R3 6.1.77 #0 SMP Fri Feb 16 13:10:11 2024 aarch64 GNU/Linux

root@BananaPi_BPi-R3 /root [#]# dmesg | tail
...
[14201.969043] sfp sfp-2: module WTD              RTXM191-400      rev 3.0  sn EC163400400110   dc 160821
[14202.018092] hwmon hwmon5: temp1_input not attached to any thermal zone
[14209.601313] mt7530-mdio mdio-bus:1f sfp2: Link is Up - 1Gbps/Full - flow control rx/tx
[14209.609591] br-lan: port 5(sfp2) entered blocking state
[14209.614815] br-lan: port 5(sfp2) entered forwarding state
[14211.119182] net_ratelimit: 4 callbacks suppressed
[14211.119195] br-lan: received packet on sfp2 with own address as source address (addr:a6:bb:0f:ed:50:d6, vlan:0)
[14212.157973] br-lan: received packet on sfp2 with own address as source address (addr:a6:bb:0f:ed:50:d6, vlan:0)
[14213.196808] br-lan: received packet on sfp2 with own address as source address (addr:a6:bb:0f:ed:50:d6, vlan:0)

root@BananaPi_BPi-R3 /root [#]# ethtool sfp2
Settings for sfp2:
        Supported ports: [ FIBRE ]
        Supported link modes:   1000baseX/Full
        Supported pause frame use: Symmetric Receive-only
        Supports auto-negotiation: Yes
        Supported FEC modes: Not reported
        Advertised link modes:  1000baseX/Full
        Advertised pause frame use: Symmetric Receive-only
        Advertised auto-negotiation: Yes
        Advertised FEC modes: Not reported
        Link partner advertised link modes:  1000baseX/Full
        Link partner advertised pause frame use: Symmetric Receive-only
        Link partner advertised auto-negotiation: Yes
        Link partner advertised FEC modes: Not reported
        Speed: 1000Mb/s
        Duplex: Full
        Auto-negotiation: on
        Port: FIBRE
        PHYAD: 0
        Transceiver: internal
        Supports Wake-on: d
        Wake-on: d
        Link detected: yes
root@BananaPi_BPi-R3 /root [#]# ethtool -m sfp2
        Identifier                                : 0x03 (SFP)
        Extended identifier                       : 0x04 (GBIC/SFP defined by 2-wire interface ID)
        Connector                                 : 0x07 (LC)
        Transceiver codes                         : 0x00 0x00 0x00 0x02 0x42 0x10 0x01 0x00 0x00
        Transceiver type                          : Ethernet: 1000BASE-LX
        Transceiver type                          : FC: short distance (S)
        Transceiver type                          : FC: Longwave laser (LC)
        Transceiver type                          : FC: Longwave laser (LL)
        Transceiver type                          : FC: Single Mode (SM)
        Encoding                                  : 0x03 (NRZ)
        BR, Nominal                               : 1200MBd
        Rate identifier                           : 0x00 (unspecified)
        Length (SMF,km)                           : 10km
        Length (SMF)                              : 10000m
        Length (50um)                             : 0m
        Length (62.5um)                           : 0m
        Length (Copper)                           : 0m
        Length (OM3)                              : 0m
        Laser wavelength                          : 1310nm
        Vendor name                               : WTD
        Vendor OUI                                : 00:1c:ad
        Vendor PN                                 : RTXM191-400
        Vendor rev                                : 3.0
        Option values                             : 0x00 0x1a
        Option                                    : RX_LOS implemented
        Option                                    : TX_FAULT implemented
        Option                                    : TX_DISABLE implemented
        BR margin, max                            : 0%
        BR margin, min                            : 0%
        Vendor SN                                 : EC163400400110
        Date code                                 : 160821
        Optical diagnostics support               : Yes
        Laser bias current                        : 11.760 mA
        Laser output power                        : 0.2575 mW / -5.89 dBm
        Receiver signal average optical power     : 0.2313 mW / -6.36 dBm
        Module temperature                        : 37.45 degrees C / 99.41 degrees F
        Module voltage                            : 3.3022 V
        Alarm/warning flags implemented           : Yes
        Laser bias current high alarm             : Off
        Laser bias current low alarm              : Off
        Laser bias current high warning           : Off
        Laser bias current low warning            : Off
        Laser output power high alarm             : Off
        Laser output power low alarm              : Off
        Laser output power high warning           : Off
        Laser output power low warning            : Off
        Module temperature high alarm             : Off
        Module temperature low alarm              : Off
        Module temperature high warning           : Off
        Module temperature low warning            : Off
        Module voltage high alarm                 : Off
        Module voltage low alarm                  : Off
        Module voltage high warning               : Off
        Module voltage low warning                : Off
        Laser rx power high alarm                 : Off
        Laser rx power low alarm                  : Off
        Laser rx power high warning               : Off
        Laser rx power low warning                : Off
        Laser bias current high alarm threshold   : 60.000 mA
        Laser bias current low alarm threshold    : 0.000 mA
        Laser bias current high warning threshold : 60.000 mA
        Laser bias current low warning threshold  : 0.000 mA
        Laser output power high alarm threshold   : 0.7943 mW / -1.00 dBm
        Laser output power low alarm threshold    : 0.0794 mW / -11.00 dBm
        Laser output power high warning threshold : 0.5011 mW / -3.00 dBm
        Laser output power low warning threshold  : 0.1258 mW / -9.00 dBm
        Module temperature high alarm threshold   : 80.00 degrees C / 176.00 degrees F
        Module temperature low alarm threshold    : -10.00 degrees C / 14.00 degrees F
        Module temperature high warning threshold : 70.00 degrees C / 158.00 degrees F
        Module temperature low warning threshold  : 0.00 degrees C / 32.00 degrees F
        Module voltage high alarm threshold       : 3.6300 V
        Module voltage low alarm threshold        : 2.9700 V
        Module voltage high warning threshold     : 3.4650 V
        Module voltage low warning threshold      : 3.1350 V
        Laser rx power high alarm threshold       : 0.7943 mW / -1.00 dBm
        Laser rx power low alarm threshold        : 0.0063 mW / -22.01 dBm
        Laser rx power high warning threshold     : 0.5011 mW / -3.00 dBm
        Laser rx power low warning threshold      : 0.0100 mW / -20.00 dBm
root@BananaPi_BPi-R3 /root [#]#

5. CISCO GLC-LH-SM SFCT-5798PZ CLASS 1 - 1.25G 1310nm 10km SM

root@BananaPi_BPi-R3 /root [#]# uname -a
Linux BananaPi_BPi-R3 6.1.77 #0 SMP Fri Feb 16 13:10:11 2024 aarch64 GNU/Linux

root@BananaPi_BPi-R3 /root [#]# dmesg | tail
...
[22068.830292] sfp sfp-2: module CISCO-AVAGO      SFCT-5798PZ      rev 0000 sn AGC1137U37A      dc 07091601
[22076.143470] mt7530-mdio mdio-bus:1f sfp2: Link is Up - 1Gbps/Full - flow control rx/tx
[22076.151747] br-lan: port 5(sfp2) entered blocking state
[22076.156970] br-lan: port 5(sfp2) entered forwarding state
[22079.563036] br-lan: received packet on sfp2 with own address as source address (addr:a6:bb:0f:ed:50:d6, vlan:0)
[22079.573202] br-lan: received packet on sfp2 with own address as source address (addr:a6:bb:0f:ed:50:d6, vlan:0)
[22079.583304] br-lan: received packet on sfp2 with own address as source address (addr:a6:bb:0f:ed:50:d6, vlan:0)

root@BananaPi_BPi-R3 /root [#]# ethtool sfp2
Settings for sfp2:
        Supported ports: [ FIBRE ]
        Supported link modes:   1000baseX/Full
        Supported pause frame use: Symmetric Receive-only
        Supports auto-negotiation: Yes
        Supported FEC modes: Not reported
        Advertised link modes:  1000baseX/Full
        Advertised pause frame use: Symmetric Receive-only
        Advertised auto-negotiation: Yes
        Advertised FEC modes: Not reported
        Link partner advertised link modes:  1000baseX/Full
        Link partner advertised pause frame use: Symmetric Receive-only
        Link partner advertised auto-negotiation: Yes
        Link partner advertised FEC modes: Not reported
        Speed: 1000Mb/s
        Duplex: Full
        Auto-negotiation: on
        Port: FIBRE
        PHYAD: 0
        Transceiver: internal
        Supports Wake-on: d
        Wake-on: d
        Link detected: yes
root@BananaPi_BPi-R3 /root [#]# ethtool -m sfp2
        Identifier                                : 0x03 (SFP)
        Extended identifier                       : 0x04 (GBIC/SFP defined by 2-wire interface ID)
        Connector                                 : 0x07 (LC)
        Transceiver codes                         : 0x00 0x00 0x00 0x02 0x00 0x00 0x00 0x00 0x00
        Transceiver type                          : Ethernet: 1000BASE-LX
        Encoding                                  : 0x01 (8B/10B)
        BR, Nominal                               : 1200MBd
        Rate identifier                           : 0x00 (unspecified)
        Length (SMF,km)                           : 10km
        Length (SMF)                              : 10000m
        Length (50um)                             : 550m
        Length (62.5um)                           : 550m
        Length (Copper)                           : 0m
        Length (OM3)                              : 0m
        Laser wavelength                          : 1310nm
        Vendor name                               : CISCO-AVAGO
        Vendor OUI                                : 00:17:6a
        Vendor PN                                 : SFCT-5798PZ
        Vendor rev                                : 0000
        Option values                             : 0x00 0x1a
        Option                                    : RX_LOS implemented
        Option                                    : TX_FAULT implemented
        Option                                    : TX_DISABLE implemented
        BR margin, max                            : 0%
        BR margin, min                            : 0%
        Vendor SN                                 : AGC1137U37A
        Date code                                 : 07091601
root@BananaPi_BPi-R3 /root [#]#

6. CISCO SYSTEMS GLC-LH-SM CLASS 1 - 1.25G 1310nm 10km SM

root@BananaPi_BPi-R3 /root [#]# uname -a
Linux BananaPi_BPi-R3 6.1.77 #0 SMP Fri Feb 16 13:10:11 2024 aarch64 GNU/Linux

root@BananaPi_BPi-R3 /root [#]# dmesg | tail
...
[22557.294273] sfp sfp-2: module CISCO-FINISAR    FTLF1318P2BCL-CS rev 0000 sn FNS114111YT      dc 071108
[22566.513130] mt7530-mdio mdio-bus:1f sfp2: Link is Up - 1Gbps/Full - flow control rx/tx
[22566.521408] br-lan: port 5(sfp2) entered blocking state
[22566.526632] br-lan: port 5(sfp2) entered forwarding state
[22569.279003] br-lan: received packet on sfp2 with own address as source address (addr:a6:bb:0f:ed:50:d6, vlan:0)
[22569.289168] br-lan: received packet on sfp2 with own address as source address (addr:a6:bb:0f:ed:50:d6, vlan:0)
[22569.299265] br-lan: received packet on sfp2 with own address as source address (addr:a6:bb:0f:ed:50:d6, vlan:0)

root@BananaPi_BPi-R3 /root [#]# ethtool sfp2
Settings for sfp2:
        Supported ports: [ FIBRE ]
        Supported link modes:   1000baseX/Full
        Supported pause frame use: Symmetric Receive-only
        Supports auto-negotiation: Yes
        Supported FEC modes: Not reported
        Advertised link modes:  1000baseX/Full
        Advertised pause frame use: Symmetric Receive-only
        Advertised auto-negotiation: Yes
        Advertised FEC modes: Not reported
        Link partner advertised link modes:  1000baseX/Full
        Link partner advertised pause frame use: Symmetric Receive-only
        Link partner advertised auto-negotiation: Yes
        Link partner advertised FEC modes: Not reported
        Speed: 1000Mb/s
        Duplex: Full
        Auto-negotiation: on
        Port: FIBRE
        PHYAD: 0
        Transceiver: internal
        Supports Wake-on: d
        Wake-on: d
        Link detected: yes
root@BananaPi_BPi-R3 /root [#]# ethtool -m sfp2
        Identifier                                : 0x03 (SFP)
        Extended identifier                       : 0x04 (GBIC/SFP defined by 2-wire interface ID)
        Connector                                 : 0x07 (LC)
        Transceiver codes                         : 0x00 0x00 0x00 0x02 0x00 0x00 0x00 0x00 0x00
        Transceiver type                          : Ethernet: 1000BASE-LX
        Encoding                                  : 0x01 (8B/10B)
        BR, Nominal                               : 1300MBd
        Rate identifier                           : 0x00 (unspecified)
        Length (SMF,km)                           : 10km
        Length (SMF)                              : 10000m
        Length (50um)                             : 550m
        Length (62.5um)                           : 550m
        Length (Copper)                           : 0m
        Length (OM3)                              : 0m
        Laser wavelength                          : 1310nm
        Vendor name                               : CISCO-FINISAR
        Vendor OUI                                : 00:90:65
        Vendor PN                                 : FTLF1318P2BCL-CS
        Vendor rev                                : 0000
        Option values                             : 0x00 0x12
        Option                                    : RX_LOS implemented
        Option                                    : TX_DISABLE implemented
        BR margin, max                            : 0%
        BR margin, min                            : 0%
        Vendor SN                                 : FNS114111YT
        Date code                                 : 071108
root@BananaPi_BPi-R3 /root [#]#

7. CISCO SYSTEMS GLC-ZX-SM CLASS 1 - 1.25G 1550nm 80km SM

root@BananaPi_BPi-R3 /root [#]# uname -a
Linux BananaPi_BPi-R3 6.1.77 #0 SMP Fri Feb 16 13:10:11 2024 aarch64 GNU/Linux

root@BananaPi_BPi-R3 /root [#]# dmesg | tail
...
[22850.220070] sfp sfp-2: module CISCO-FINISAR    FTRJ1519P1BCL-CS rev A    sn FNS222240U8R      dc 070612
[22850.269181] hwmon hwmon5: temp1_input not attached to any thermal zone
[22858.444281] mt7530-mdio mdio-bus:1f sfp2: Link is Up - 1Gbps/Full - flow control rx/tx
[22858.452557] br-lan: port 5(sfp2) entered blocking state
[22858.457781] br-lan: port 5(sfp2) entered forwarding state
[22859.117681] br-lan: received packet on sfp2 with own address as source address (addr:a6:bb:0f:ed:50:d6, vlan:0)
[22859.127847] br-lan: received packet on sfp2 with own address as source address (addr:a6:bb:0f:ed:50:d6, vlan:0)
[22859.137945] br-lan: received packet on sfp2 with own address as source address (addr:a6:bb:0f:ed:50:d6, vlan:0)

root@BananaPi_BPi-R3 /root [#]# ethtool sfp2
Settings for sfp2:
        Supported ports: [ FIBRE ]
        Supported link modes:   1000baseX/Full
        Supported pause frame use: Symmetric Receive-only
        Supports auto-negotiation: Yes
        Supported FEC modes: Not reported
        Advertised link modes:  1000baseX/Full
        Advertised pause frame use: Symmetric Receive-only
        Advertised auto-negotiation: Yes
        Advertised FEC modes: Not reported
        Link partner advertised link modes:  1000baseX/Full
        Link partner advertised pause frame use: Symmetric Receive-only
        Link partner advertised auto-negotiation: Yes
        Link partner advertised FEC modes: Not reported
        Speed: 1000Mb/s
        Duplex: Full
        Auto-negotiation: on
        Port: FIBRE
        PHYAD: 0
        Transceiver: internal
        Supports Wake-on: d
        Wake-on: d
        Link detected: yes
root@BananaPi_BPi-R3 /root [#]# ethtool -m sfp2
        Identifier                                : 0x03 (SFP)
        Extended identifier                       : 0x04 (GBIC/SFP defined by 2-wire interface ID)
        Connector                                 : 0x07 (LC)
        Transceiver codes                         : 0x00 0x00 0x00 0x02 0x80 0x10 0x01 0x05 0x00
        Transceiver type                          : Ethernet: 1000BASE-LX
        Transceiver type                          : FC: very long distance (V)
        Transceiver type                          : FC: Longwave laser (LL)
        Transceiver type                          : FC: Single Mode (SM)
        Transceiver type                          : FC: 200 MBytes/sec
        Transceiver type                          : FC: 100 MBytes/sec
        Encoding                                  : 0x01 (8B/10B)
        BR, Nominal                               : 2500MBd
        Rate identifier                           : 0x00 (unspecified)
        Length (SMF,km)                           : 76km
        Length (SMF)                              : 25500m
        Length (50um)                             : 0m
        Length (62.5um)                           : 0m
        Length (Copper)                           : 0m
        Length (OM3)                              : 0m
        Laser wavelength                          : 1550nm
        Vendor name                               : CISCO-FINISAR
        Vendor OUI                                : 00:90:65
        Vendor PN                                 : FTRJ1519P1BCL-CS
        Vendor rev                                : A
        Option values                             : 0x00 0x1a
        Option                                    : RX_LOS implemented
        Option                                    : TX_FAULT implemented
        Option                                    : TX_DISABLE implemented
        BR margin, max                            : 0%
        BR margin, min                            : 0%
        Vendor SN                                 : FNS22240U8R
        Date code                                 : 070612
        Optical diagnostics support               : Yes
        Laser bias current                        : 22.444 mA
        Laser output power                        : 2.0309 mW / 3.08 dBm
        Receiver signal average optical power     : 1.2438 mW / -9.95 dBm
        Module temperature                        : 48.29 degrees C / 118.92 degrees F
        Module voltage                            : 3.3312 V
        Alarm/warning flags implemented           : Yes
        Laser bias current high alarm             : Off
        Laser bias current low alarm              : Off
        Laser bias current high warning           : Off
        Laser bias current low warning            : Off
        Laser output power high alarm             : Off
        Laser output power low alarm              : Off
        Laser output power high warning           : Off
        Laser output power low warning            : Off
        Module temperature high alarm             : Off
        Module temperature low alarm              : Off
        Module temperature high warning           : Off
        Module temperature low warning            : Off
        Module voltage high alarm                 : Off
        Module voltage low alarm                  : Off
        Module voltage high warning               : Off
        Module voltage low warning                : Off
        Laser rx power high alarm                 : Off
        Laser rx power low alarm                  : Off
        Laser rx power high warning               : Off
        Laser rx power low warning                : Off
        Laser bias current high alarm threshold   : 84.000 mA
        Laser bias current low alarm threshold    : 2.000 mA
        Laser bias current high warning threshold : 70.000 mA
        Laser bias current low warning threshold  : 4.000 mA
        Laser output power high alarm threshold   : 6.5407 mW / 8.16 dBm
        Laser output power low alarm threshold    : 0.3974 mW / -4.01 dBm
        Laser output power high warning threshold : 5.0047 mW / 6.99 dBm
        Laser output power low warning threshold  : 0.6300 mW / -2.01 dBm
        Module temperature high alarm threshold   : 110.00 degrees C / 230.00 degrees F
        Module temperature low alarm threshold    : -9.00 degrees C / 15.80 degrees F
        Module temperature high warning threshold : 93.00 degrees C / 199.40 degrees F
        Module temperature low warning threshold  : -3.00 degrees C / 26.60 degrees F
        Module voltage high alarm threshold       : 4.0000 V
        Module voltage low alarm threshold        : 2.8000 V
        Module voltage high warning threshold     : 3.7000 V
        Module voltage low warning threshold      : 2.9000 V
        Laser rx power high alarm threshold       : 1.1940 mW / 0.77 dBm
        Laser rx power low alarm threshold        : 0.0039 mW / -24.09 dBm
        Laser rx power high warning threshold     : 0.7942 mW / -1.00 dBm
        Laser rx power low warning threshold      : 0.0099 mW / -20.04 dBm
root@BananaPi_BPi-R3 /root [#]#

Kolejne 1Gbps poniżej, bo się nie mieszczą w jednym poście ...

Banana Pi BPI-R3 + SFP GPON ONT Nokia G-010S-A + LTE FIBOCOM L860-GL-16 (OpenWrt 25.12-SNAPSHOT, kernel 6.12.71)
Xiaomi AX3600 (OpenWrt 25.12-SNAPSHOT, kernel 6.12.71)
Xiaomi AX3000T (OpenWrt 25.12-SNAPSHOT, kernel 6.12.71)
All OpenWRT compilations from ASU by @Cezary

24 Odpowiedź przez Payti (edytowany przez Payti 2024-02-20 20:07:29)

  • Payti
  • Payti
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2012-01-05
  • Posty: 374

Odp: BPi-R3 i wkładka SFP GPON ONT oraz inne wkładki SFP 1Gbps, 2.5Gbps

Ciąg dalszy poprzedniego posta ...


8. Alcatel-Lucent 3HE00028CA MFGR P/N: SP-GB-LX-IDFN-AL - 1.25G 1310nm 10km SM

root@BananaPi_BPi-R3 /root [#]# uname -a
Linux BananaPi_BPi-R3 6.1.77 #0 SMP Fri Feb 16 13:10:11 2024 aarch64 GNU/Linux

root@BananaPi_BPi-R3 /root [#]# dmesg | tail
...
[23374.870157] sfp sfp-2: module SOURCEPHOTONICS  SPGBLXIDFNAL     rev 10   sn C4O2224689       dc 120306
[23374.919301] hwmon hwmon5: temp1_input not attached to any thermal zone
[23385.198743] mt7530-mdio mdio-bus:1f sfp2: Link is Up - 1Gbps/Full - flow control rx/tx
[23385.207019] br-lan: port 5(sfp2) entered blocking state
[23385.212243] br-lan: port 5(sfp2) entered forwarding state
[23388.851815] br-lan: received packet on sfp2 with own address as source address (addr:a6:bb:0f:ed:50:d6, vlan:0)
[23388.861958] br-lan: received packet on sfp2 with own address as source address (addr:a6:bb:0f:ed:50:d6, vlan:0)
[23388.872080] br-lan: received packet on sfp2 with own address as source address (addr:a6:bb:0f:ed:50:d6, vlan:0)

root@BananaPi_BPi-R3 /root [#]# ethtool sfp2
Settings for sfp2:
        Supported ports: [ FIBRE ]
        Supported link modes:   1000baseX/Full
        Supported pause frame use: Symmetric Receive-only
        Supports auto-negotiation: Yes
        Supported FEC modes: Not reported
        Advertised link modes:  1000baseX/Full
        Advertised pause frame use: Symmetric Receive-only
        Advertised auto-negotiation: Yes
        Advertised FEC modes: Not reported
        Link partner advertised link modes:  1000baseX/Full
        Link partner advertised pause frame use: Symmetric Receive-only
        Link partner advertised auto-negotiation: Yes
        Link partner advertised FEC modes: Not reported
        Speed: 1000Mb/s
        Duplex: Full
        Auto-negotiation: on
        Port: FIBRE
        PHYAD: 0
        Transceiver: internal
        Supports Wake-on: d
        Wake-on: d
        Link detected: yes
root@BananaPi_BPi-R3 /root [#]# ethtool -m sfp2
        Identifier                                : 0x03 (SFP)
        Extended identifier                       : 0x04 (GBIC/SFP defined by 2-wire interface ID)
        Connector                                 : 0x07 (LC)
        Transceiver codes                         : 0x00 0x00 0x00 0x02 0x12 0x00 0x01 0x01 0x00
        Transceiver type                          : Ethernet: 1000BASE-LX
        Transceiver type                          : FC: long distance (L)
        Transceiver type                          : FC: Longwave laser (LC)
        Transceiver type                          : FC: Single Mode (SM)
        Transceiver type                          : FC: 100 MBytes/sec
        Encoding                                  : 0x01 (8B/10B)
        BR, Nominal                               : 1300MBd
        Rate identifier                           : 0x00 (unspecified)
        Length (SMF,km)                           : 10km
        Length (SMF)                              : 10000m
        Length (50um)                             : 0m
        Length (62.5um)                           : 0m
        Length (Copper)                           : 0m
        Length (OM3)                              : 0m
        Laser wavelength                          : 1310nm
        Vendor name                               : SOURCEPHOTONICS
        Vendor OUI                                : 00:1f:22
        Vendor PN                                 : SPGBLXIDFNAL
        Vendor rev                                : 10
        Option values                             : 0x00 0x1a
        Option                                    : RX_LOS implemented
        Option                                    : TX_FAULT implemented
        Option                                    : TX_DISABLE implemented
        BR margin, max                            : 0%
        BR margin, min                            : 0%
        Vendor SN                                 : C4O2224689
        Date code                                 : 120306
        Optical diagnostics support               : Yes
        Laser bias current                        : 17.152 mA
        Laser output power                        : 0.2464 mW / -6.08 dBm
        Receiver signal average optical power     : 0.3030 mW / -5.19 dBm
        Module temperature                        : 47.69 degrees C / 117.84 degrees F
        Module voltage                            : 3.2904 V
        Alarm/warning flags implemented           : Yes
        Laser bias current high alarm             : Off
        Laser bias current low alarm              : Off
        Laser bias current high warning           : Off
        Laser bias current low warning            : Off
        Laser output power high alarm             : Off
        Laser output power low alarm              : Off
        Laser output power high warning           : Off
        Laser output power low warning            : Off
        Module temperature high alarm             : Off
        Module temperature low alarm              : Off
        Module temperature high warning           : Off
        Module temperature low warning            : Off
        Module voltage high alarm                 : Off
        Module voltage low alarm                  : Off
        Module voltage high warning               : Off
        Module voltage low warning                : Off
        Laser rx power high alarm                 : Off
        Laser rx power low alarm                  : Off
        Laser rx power high warning               : Off
        Laser rx power low warning                : Off
        Laser bias current high alarm threshold   : 70.000 mA
        Laser bias current low alarm threshold    : 0.100 mA
        Laser bias current high warning threshold : 60.000 mA
        Laser bias current low warning threshold  : 0.200 mA
        Laser output power high alarm threshold   : 0.6310 mW / -2.00 dBm
        Laser output power low alarm threshold    : 0.1000 mW / -10.00 dBm
        Laser output power high warning threshold : 0.5012 mW / -3.00 dBm
        Laser output power low warning threshold  : 0.1259 mW / -9.00 dBm
        Module temperature high alarm threshold   : 100.00 degrees C / 212.00 degrees F
        Module temperature low alarm threshold    : -40.00 degrees C / -40.00 degrees F
        Module temperature high warning threshold : 95.00 degrees C / 203.00 degrees F
        Module temperature low warning threshold  : -35.00 degrees C / -31.00 degrees F
        Module voltage high alarm threshold       : 3.7000 V
        Module voltage low alarm threshold        : 2.9000 V
        Module voltage high warning threshold     : 3.6000 V
        Module voltage low warning threshold      : 3.0000 V
        Laser rx power high alarm threshold       : 0.6310 mW / -2.00 dBm
        Laser rx power low alarm threshold        : 0.0063 mW / -22.01 dBm
        Laser rx power high warning threshold     : 0.5012 mW / -3.00 dBm
        Laser rx power low warning threshold      : 0.0079 mW / -21.02 dBm
root@BananaPi_BPi-R3 /root [#]#

9. Alcatel-Lucent 3HE00029CA 01 SCP6G94-A8-AWH - 1.25G 1550nm 80km SM

root@BananaPi_BPi-R3 /root [#]# uname -a
Linux BananaPi_BPi-R3 6.1.77 #0 SMP Fri Feb 16 13:10:11 2024 aarch64 GNU/Linux

root@BananaPi_BPi-R3 /root [#]# dmesg | tail
...
[23817.246370] sfp sfp-2: module SumitomoElectric SCP6G94-A8-AWH   rev A    sn 23T721622974     dc 120421
[23817.295553] hwmon hwmon5: temp1_input not attached to any thermal zone
[23825.648661] mt7530-mdio mdio-bus:1f sfp2: Link is Up - 1Gbps/Full - flow control rx/tx
[23825.656938] br-lan: port 5(sfp2) entered blocking state
[23825.662163] br-lan: port 5(sfp2) entered forwarding state
[23828.543251] br-lan: received packet on sfp2 with own address as source address (addr:a6:bb:0f:ed:50:d6, vlan:0)
[23828.553386] br-lan: received packet on sfp2 with own address as source address (addr:a6:bb:0f:ed:50:d6, vlan:0)
[23828.563473] br-lan: received packet on sfp2 with own address as source address (addr:a6:bb:0f:ed:50:d6, vlan:0)

root@BananaPi_BPi-R3 /root [#]# ethtool sfp2
Settings for sfp2:
        Supported ports: [ FIBRE ]
        Supported link modes:   1000baseX/Full
        Supported pause frame use: Symmetric Receive-only
        Supports auto-negotiation: Yes
        Supported FEC modes: Not reported
        Advertised link modes:  1000baseX/Full
        Advertised pause frame use: Symmetric Receive-only
        Advertised auto-negotiation: Yes
        Advertised FEC modes: Not reported
        Link partner advertised link modes:  1000baseX/Full
        Link partner advertised pause frame use: Symmetric Receive-only
        Link partner advertised auto-negotiation: Yes
        Link partner advertised FEC modes: Not reported
        Speed: 1000Mb/s
        Duplex: Full
        Auto-negotiation: on
        Port: FIBRE
        PHYAD: 0
        Transceiver: internal
        Supports Wake-on: d
        Wake-on: d
        Link detected: yes
root@BananaPi_BPi-R3 /root [#]# ethtool -m sfp2
        Identifier                                : 0x03 (SFP)
        Extended identifier                       : 0x04 (GBIC/SFP defined by 2-wire interface ID)
        Connector                                 : 0x07 (LC)
        Transceiver codes                         : 0x00 0x00 0x00 0x02 0x00 0x00 0x00 0x00 0x00
        Transceiver type                          : Ethernet: 1000BASE-LX
        Encoding                                  : 0x01 (8B/10B)
        BR, Nominal                               : 1300MBd
        Rate identifier                           : 0x00 (unspecified)
        Length (SMF,km)                           : 80km
        Length (SMF)                              : 25500m
        Length (50um)                             : 0m
        Length (62.5um)                           : 0m
        Length (Copper)                           : 0m
        Length (OM3)                              : 0m
        Laser wavelength                          : 1550nm
        Vendor name                               : SumitomoElectric
        Vendor OUI                                : 00:00:5f
        Vendor PN                                 : SCP6G94-A8-AWH
        Vendor rev                                : A
        Option values                             : 0x00 0x1a
        Option                                    : RX_LOS implemented
        Option                                    : TX_FAULT implemented
        Option                                    : TX_DISABLE implemented
        BR margin, max                            : 0%
        BR margin, min                            : 0%
        Vendor SN                                 : 23T721622974
        Date code                                 : 120421
        Optical diagnostics support               : Yes
        Laser bias current                        : 12.632 mA
        Laser output power                        : 1.7399 mW / 2.41 dBm
        Receiver signal average optical power     : 1.6646 mW / -7.21 dBm
        Module temperature                        : 35.14 degrees C / 95.25 degrees F
        Module voltage                            : 3.3101 V
        Alarm/warning flags implemented           : Yes
        Laser bias current high alarm             : Off
        Laser bias current low alarm              : Off
        Laser bias current high warning           : Off
        Laser bias current low warning            : Off
        Laser output power high alarm             : Off
        Laser output power low alarm              : Off
        Laser output power high warning           : Off
        Laser output power low warning            : Off
        Module temperature high alarm             : Off
        Module temperature low alarm              : Off
        Module temperature high warning           : Off
        Module temperature low warning            : Off
        Module voltage high alarm                 : Off
        Module voltage low alarm                  : Off
        Module voltage high warning               : Off
        Module voltage low warning                : Off
        Laser rx power high alarm                 : Off
        Laser rx power low alarm                  : Off
        Laser rx power high warning               : Off
        Laser rx power low warning                : Off
        Laser bias current high alarm threshold   : 70.000 mA
        Laser bias current low alarm threshold    : 0.000 mA
        Laser bias current high warning threshold : 60.000 mA
        Laser bias current low warning threshold  : 0.100 mA
        Laser output power high alarm threshold   : 6.3095 mW / 8.00 dBm
        Laser output power low alarm threshold    : 0.5011 mW / -3.00 dBm
        Laser output power high warning threshold : 3.9810 mW / 6.00 dBm
        Laser output power low warning threshold  : 0.7943 mW / -1.00 dBm
        Module temperature high alarm threshold   : 98.00 degrees C / 208.40 degrees F
        Module temperature low alarm threshold    : -45.00 degrees C / -49.00 degrees F
        Module temperature high warning threshold : 88.00 degrees C / 190.40 degrees F
        Module temperature low warning threshold  : -43.00 degrees C / -45.40 degrees F
        Module voltage high alarm threshold       : 4.1200 V
        Module voltage low alarm threshold        : 2.8000 V
        Module voltage high warning threshold     : 3.6000 V
        Module voltage low warning threshold      : 3.0000 V
        Laser rx power high alarm threshold       : 1.0000 mW / 0.00 dBm
        Laser rx power low alarm threshold        : 0.0040 mW / -23.98 dBm
        Laser rx power high warning threshold     : 0.7944 mW / -1.00 dBm
        Laser rx power low warning threshold      : 0.0051 mW / -22.92 dBm
root@BananaPi_BPi-R3 /root [#]#

10. SUMITOMO ELECTRIC SCP6G44-H2-BWE - 1.25G-1310nm-10km-SM-ESFP

root@BananaPi_BPi-R3 /root [#]# uname -a
Linux BananaPi_BPi-R3 6.1.77 #0 SMP Fri Feb 16 13:10:11 2024 aarch64 GNU/Linux

root@BananaPi_BPi-R3 /root [#]# dmesg | tail
...
[24221.226079] sfp sfp-2: module SumitomoElectric SCP6G44-H2-BWE   rev A    sn 07T442633358     dc 130722
[24221.275236] hwmon hwmon5: temp1_input not attached to any thermal zone
[24229.777201] mt7530-mdio mdio-bus:1f sfp2: Link is Up - 1Gbps/Full - flow control rx/tx
[24229.785479] br-lan: port 5(sfp2) entered blocking state
[24229.790705] br-lan: port 5(sfp2) entered forwarding state
[24238.258395] br-lan: received packet on sfp2 with own address as source address (addr:a6:bb:0f:ed:50:d6, vlan:0)
[24238.268532] br-lan: received packet on sfp2 with own address as source address (addr:a6:bb:0f:ed:50:d6, vlan:0)
[24238.278622] br-lan: received packet on sfp2 with own address as source address (addr:a6:bb:0f:ed:50:d6, vlan:0)

root@BananaPi_BPi-R3 /root [#]# ethtool sfp2
Settings for sfp2:
        Supported ports: [ FIBRE ]
        Supported link modes:   1000baseX/Full
        Supported pause frame use: Symmetric Receive-only
        Supports auto-negotiation: Yes
        Supported FEC modes: Not reported
        Advertised link modes:  1000baseX/Full
        Advertised pause frame use: Symmetric Receive-only
        Advertised auto-negotiation: Yes
        Advertised FEC modes: Not reported
        Link partner advertised link modes:  1000baseX/Full
        Link partner advertised pause frame use: Symmetric Receive-only
        Link partner advertised auto-negotiation: Yes
        Link partner advertised FEC modes: Not reported
        Speed: 1000Mb/s
        Duplex: Full
        Auto-negotiation: on
        Port: FIBRE
        PHYAD: 0
        Transceiver: internal
        Supports Wake-on: d
        Wake-on: d
        Link detected: yes
root@BananaPi_BPi-R3 /root [#]# ethtool -m sfp2
        Identifier                                : 0x03 (SFP)
        Extended identifier                       : 0x04 (GBIC/SFP defined by 2-wire interface ID)
        Connector                                 : 0x07 (LC)
        Transceiver codes                         : 0x00 0x00 0x00 0x02 0x12 0x00 0x01 0x01 0x00
        Transceiver type                          : Ethernet: 1000BASE-LX
        Transceiver type                          : FC: long distance (L)
        Transceiver type                          : FC: Longwave laser (LC)
        Transceiver type                          : FC: Single Mode (SM)
        Transceiver type                          : FC: 100 MBytes/sec
        Encoding                                  : 0x01 (8B/10B)
        BR, Nominal                               : 1300MBd
        Rate identifier                           : 0x00 (unspecified)
        Length (SMF,km)                           : 10km
        Length (SMF)                              : 10000m
        Length (50um)                             : 550m
        Length (62.5um)                           : 550m
        Length (Copper)                           : 0m
        Length (OM3)                              : 0m
        Laser wavelength                          : 1310nm
        Vendor name                               : SumitomoElectric
        Vendor OUI                                : 00:00:5f
        Vendor PN                                 : SCP6G44-H2-BWE
        Vendor rev                                : A
        Option values                             : 0x00 0x1a
        Option                                    : RX_LOS implemented
        Option                                    : TX_FAULT implemented
        Option                                    : TX_DISABLE implemented
        BR margin, max                            : 0%
        BR margin, min                            : 0%
        Vendor SN                                 : 07T442633358
        Date code                                 : 130722
        Optical diagnostics support               : Yes
        Laser bias current                        : 6.130 mA
        Laser output power                        : 0.1867 mW / -7.29 dBm
        Receiver signal average optical power     : 0.1880 mW / -7.26 dBm
        Module temperature                        : 36.97 degrees C / 98.55 degrees F
        Module voltage                            : 3.3050 V
        Alarm/warning flags implemented           : Yes
        Laser bias current high alarm             : Off
        Laser bias current low alarm              : Off
        Laser bias current high warning           : Off
        Laser bias current low warning            : Off
        Laser output power high alarm             : Off
        Laser output power low alarm              : Off
        Laser output power high warning           : Off
        Laser output power low warning            : Off
        Module temperature high alarm             : Off
        Module temperature low alarm              : Off
        Module temperature high warning           : Off
        Module temperature low warning            : Off
        Module voltage high alarm                 : Off
        Module voltage low alarm                  : Off
        Module voltage high warning               : Off
        Module voltage low warning                : Off
        Laser rx power high alarm                 : Off
        Laser rx power low alarm                  : Off
        Laser rx power high warning               : Off
        Laser rx power low warning                : Off
        Laser bias current high alarm threshold   : 60.000 mA
        Laser bias current low alarm threshold    : 0.000 mA
        Laser bias current high warning threshold : 50.000 mA
        Laser bias current low warning threshold  : 0.000 mA
        Laser output power high alarm threshold   : 1.0000 mW / 0.00 dBm
        Laser output power low alarm threshold    : 0.0630 mW / -12.01 dBm
        Laser output power high warning threshold : 0.5011 mW / -3.00 dBm
        Laser output power low warning threshold  : 0.1258 mW / -9.00 dBm
        Module temperature high alarm threshold   : 105.00 degrees C / 221.00 degrees F
        Module temperature low alarm threshold    : -45.00 degrees C / -49.00 degrees F
        Module temperature high warning threshold : 95.00 degrees C / 203.00 degrees F
        Module temperature low warning threshold  : -45.00 degrees C / -49.00 degrees F
        Module voltage high alarm threshold       : 4.0000 V
        Module voltage low alarm threshold        : 2.8000 V
        Module voltage high warning threshold     : 3.6000 V
        Module voltage low warning threshold      : 3.0000 V
        Laser rx power high alarm threshold       : 0.5012 mW / -3.00 dBm
        Laser rx power low alarm threshold        : 0.0126 mW / -19.00 dBm
        Laser rx power high warning threshold     : 0.5012 mW / -3.00 dBm
        Laser rx power low warning threshold      : 0.0126 mW / -19.00 dBm
root@BananaPi_BPi-R3 /root [#]#

11. HUAWEI MXPD-243S - 1.25G-1310nm-10km-SM-ESFP

root@BananaPi_BPi-R3 /root [#]# uname -a
Linux BananaPi_BPi-R3 6.1.77 #0 SMP Fri Feb 16 13:10:11 2024 aarch64 GNU/Linux

root@BananaPi_BPi-R3 /root [#]# dmesg | tail
...
[ 9336.273625] sfp sfp-2: module HG GENUINE       MXPD-243S        rev  sn HB16550891481    dc 160320
[ 9336.282772] mt7530-mdio mdio-bus:1f sfp2: switched to inband/1000base-x link mode
[ 9336.332748] hwmon hwmon6: temp1_input not attached to any thermal zone
[ 9344.585668] mt7530-mdio mdio-bus:1f sfp2: Link is Up - 1Gbps/Full - flow control rx/tx
[ 9344.593944] br-lan: port 5(sfp2) entered blocking state
[ 9344.599167] br-lan: port 5(sfp2) entered forwarding state
[ 9345.629753] br-lan: received packet on sfp2 with own address as source address (addr:a6:bb:0f:ed:50:d6, vlan:0)
[ 9345.639845] br-lan: received packet on sfp2 with own address as source address (addr:a6:bb:0f:ed:50:d6, vlan:0)
[ 9345.830380] br-lan: received packet on sfp2 with own address as source address (addr:a6:bb:0f:ed:50:d6, vlan:0)

root@BananaPi_BPi-R3 /root [#]# ethtool sfp2
Settings for sfp2:
        Supported ports: [ FIBRE ]
        Supported link modes:   1000baseX/Full
        Supported pause frame use: Symmetric Receive-only
        Supports auto-negotiation: Yes
        Supported FEC modes: Not reported
        Advertised link modes:  1000baseX/Full
        Advertised pause frame use: Symmetric Receive-only
        Advertised auto-negotiation: Yes
        Advertised FEC modes: Not reported
        Link partner advertised link modes:  1000baseX/Full
        Link partner advertised pause frame use: Symmetric Receive-only
        Link partner advertised auto-negotiation: Yes
        Link partner advertised FEC modes: Not reported
        Speed: 1000Mb/s
        Duplex: Full
        Auto-negotiation: on
        Port: FIBRE
        PHYAD: 0
        Transceiver: internal
        Supports Wake-on: d
        Wake-on: d
        Link detected: yes
root@BananaPi_BPi-R3 /root [#]# ethtool -m sfp2
        Identifier                                : 0x03 (SFP)
        Extended identifier                       : 0x04 (GBIC/SFP defined by 2-wire interface ID)
        Connector                                 : 0x07 (LC)
        Transceiver codes                         : 0x00 0x00 0x00 0x02 0x12 0x00 0x01 0x01 0x00
        Transceiver type                          : Ethernet: 1000BASE-LX
        Transceiver type                          : FC: long distance (L)
        Transceiver type                          : FC: Longwave laser (LC)
        Transceiver type                          : FC: Single Mode (SM)
        Transceiver type                          : FC: 100 MBytes/sec
        Encoding                                  : 0x01 (8B/10B)
        BR, Nominal                               : 1300MBd
        Rate identifier                           : 0x00 (unspecified)
        Length (SMF,km)                           : 10km
        Length (SMF)                              : 10000m
        Length (50um)                             : 0m
        Length (62.5um)                           : 0m
        Length (Copper)                           : 0m
        Length (OM3)                              : 0m
        Laser wavelength                          : 1310nm
        Vendor name                               : HG GENUINE
        Vendor OUI                                : 00:00:00
        Vendor PN                                 : MXPD-243S
        Vendor rev                                : ____
        Option values                             : 0x00 0x1a
        Option                                    : RX_LOS implemented
        Option                                    : TX_FAULT implemented
        Option                                    : TX_DISABLE implemented
        BR margin, max                            : 0%
        BR margin, min                            : 0%
        Vendor SN                                 : HB16550891481
        Date code                                 : 160320
        Optical diagnostics support               : Yes
        Laser bias current                        : 15.006 mA
        Laser output power                        : 0.2249 mW / -6.48 dBm
        Receiver signal average optical power     : 0.2524 mW / -5.98 dBm
        Module temperature                        : 30.33 degrees C / 86.59 degrees F
        Module voltage                            : 3.3912 V
        Alarm/warning flags implemented           : Yes
        Laser bias current high alarm             : Off
        Laser bias current low alarm              : Off
        Laser bias current high warning           : Off
        Laser bias current low warning            : Off
        Laser output power high alarm             : Off
        Laser output power low alarm              : Off
        Laser output power high warning           : Off
        Laser output power low warning            : Off
        Module temperature high alarm             : Off
        Module temperature low alarm              : Off
        Module temperature high warning           : Off
        Module temperature low warning            : Off
        Module voltage high alarm                 : Off
        Module voltage low alarm                  : Off
        Module voltage high warning               : Off
        Module voltage low warning                : Off
        Laser rx power high alarm                 : Off
        Laser rx power low alarm                  : Off
        Laser rx power high warning               : Off
        Laser rx power low warning                : Off
        Laser bias current high alarm threshold   : 60.000 mA
        Laser bias current low alarm threshold    : 0.000 mA
        Laser bias current high warning threshold : 50.000 mA
        Laser bias current low warning threshold  : 0.000 mA
        Laser output power high alarm threshold   : 0.7943 mW / -1.00 dBm
        Laser output power low alarm threshold    : 0.0794 mW / -11.00 dBm
        Laser output power high warning threshold : 0.5012 mW / -3.00 dBm
        Laser output power low warning threshold  : 0.1259 mW / -9.00 dBm
        Module temperature high alarm threshold   : 80.00 degrees C / 176.00 degrees F
        Module temperature low alarm threshold    : -10.00 degrees C / 14.00 degrees F
        Module temperature high warning threshold : 70.00 degrees C / 158.00 degrees F
        Module temperature low warning threshold  : 0.00 degrees C / 32.00 degrees F
        Module voltage high alarm threshold       : 3.6300 V
        Module voltage low alarm threshold        : 2.9700 V
        Module voltage high warning threshold     : 3.4650 V
        Module voltage low warning threshold      : 3.1350 V
        Laser rx power high alarm threshold       : 0.7943 mW / -1.00 dBm
        Laser rx power low alarm threshold        : 0.0063 mW / -22.01 dBm
        Laser rx power high warning threshold     : 0.5012 mW / -3.00 dBm
        Laser rx power low warning threshold      : 0.0100 mW / -20.00 dBm
root@BananaPi_BPi-R3 /root [#]#

12. NeoPhotonics PT7620-51-3W - 1.25G 1550nm 80km SM ESFP

root@BananaPi_BPi-R3 /root [#]# uname -a
Linux BananaPi_BPi-R3 6.1.77 #0 SMP Fri Feb 16 13:10:11 2024 aarch64 GNU/Linux

root@BananaPi_BPi-R3 /root [#]# dmesg | tail
...
[11247.968422] sfp sfp-2: module NEOPHOTONICS     PT7620-51-3W     rev 1.0  sn A0613643570      dc 130715
[11248.017513] hwmon hwmon6: temp1_input not attached to any thermal zone
[11260.316099] mt7530-mdio mdio-bus:1f sfp2: Link is Up - 1Gbps/Full - flow control rx/tx
[11260.324372] br-lan: port 5(sfp2) entered blocking state
[11260.329595] br-lan: port 5(sfp2) entered forwarding state
[11261.481804] net_ratelimit: 8 callbacks suppressed
[11261.481818] br-lan: received packet on sfp2 with own address as source address (addr:a6:bb:0f:ed:50:d6, vlan:0)
[11261.496729] br-lan: received packet on sfp2 with own address as source address (addr:a6:bb:0f:ed:50:d6, vlan:0)
[11261.506831] br-lan: received packet on sfp2 with own address as source address (addr:a6:bb:0f:ed:50:d6, vlan:0)

root@BananaPi_BPi-R3 /root [#]# ethtool sfp2
Settings for sfp2:
        Supported ports: [ FIBRE ]
        Supported link modes:   1000baseX/Full
        Supported pause frame use: Symmetric Receive-only
        Supports auto-negotiation: Yes
        Supported FEC modes: Not reported
        Advertised link modes:  1000baseX/Full
        Advertised pause frame use: Symmetric Receive-only
        Advertised auto-negotiation: Yes
        Advertised FEC modes: Not reported
        Link partner advertised link modes:  1000baseX/Full
        Link partner advertised pause frame use: Symmetric Receive-only
        Link partner advertised auto-negotiation: Yes
        Link partner advertised FEC modes: Not reported
        Speed: 1000Mb/s
        Duplex: Full
        Auto-negotiation: on
        Port: FIBRE
        PHYAD: 0
        Transceiver: internal
        Supports Wake-on: d
        Wake-on: d
        Link detected: yes
root@BananaPi_BPi-R3 /root [#]# ethtool -m sfp2
        Identifier                                : 0x03 (SFP)
        Extended identifier                       : 0x04 (GBIC/SFP defined by 2-wire interface ID)
        Connector                                 : 0x07 (LC)
        Transceiver codes                         : 0x00 0x00 0x00 0x02 0x12 0x00 0x01 0x01 0x00
        Transceiver type                          : Ethernet: 1000BASE-LX
        Transceiver type                          : FC: long distance (L)
        Transceiver type                          : FC: Longwave laser (LC)
        Transceiver type                          : FC: Single Mode (SM)
        Transceiver type                          : FC: 100 MBytes/sec
        Encoding                                  : 0x01 (8B/10B)
        BR, Nominal                               : 1200MBd
        Rate identifier                           : 0x00 (unspecified)
        Length (SMF,km)                           : 80km
        Length (SMF)                              : 25500m
        Length (50um)                             : 0m
        Length (62.5um)                           : 0m
        Length (Copper)                           : 0m
        Length (OM3)                              : 0m
        Laser wavelength                          : 1550nm
        Vendor name                               : NEOPHOTONICS
        Vendor OUI                                : 00:00:00
        Vendor PN                                 : PT7620-51-3W
        Vendor rev                                : 1.0
        Option values                             : 0x00 0x1a
        Option                                    : RX_LOS implemented
        Option                                    : TX_FAULT implemented
        Option                                    : TX_DISABLE implemented
        BR margin, max                            : 0%
        BR margin, min                            : 0%
        Vendor SN                                 : A0613643570
        Date code                                 : 130715
        Optical diagnostics support               : Yes
        Laser bias current                        : 14.740 mA
        Laser output power                        : 1.8419 mW / 2.65 dBm
        Receiver signal average optical power     : 0.0343 mW / -14.65 dBm
        Module temperature                        : 67.03 degrees C / 152.66 degrees F
        Module voltage                            : 3.3196 V
        Alarm/warning flags implemented           : Yes
        Laser bias current high alarm             : Off
        Laser bias current low alarm              : Off
        Laser bias current high warning           : Off
        Laser bias current low warning            : Off
        Laser output power high alarm             : Off
        Laser output power low alarm              : Off
        Laser output power high warning           : Off
        Laser output power low warning            : Off
        Module temperature high alarm             : Off
        Module temperature low alarm              : Off
        Module temperature high warning           : Off
        Module temperature low warning            : Off
        Module voltage high alarm                 : Off
        Module voltage low alarm                  : Off
        Module voltage high warning               : Off
        Module voltage low warning                : Off
        Laser rx power high alarm                 : Off
        Laser rx power low alarm                  : Off
        Laser rx power high warning               : Off
        Laser rx power low warning                : Off
        Laser bias current high alarm threshold   : 69.996 mA
        Laser bias current low alarm threshold    : 0.000 mA
        Laser bias current high warning threshold : 60.002 mA
        Laser bias current low warning threshold  : 0.000 mA
        Laser output power high alarm threshold   : 3.6483 mW / 5.62 dBm
        Laser output power low alarm threshold    : 0.9167 mW / -0.38 dBm
        Laser output power high warning threshold : 2.8975 mW / 4.62 dBm
        Laser output power low warning threshold  : 1.1537 mW / 0.62 dBm
        Module temperature high alarm threshold   : 100.00 degrees C / 212.00 degrees F
        Module temperature low alarm threshold    : -10.00 degrees C / 14.00 degrees F
        Module temperature high warning threshold : 95.00 degrees C / 203.00 degrees F
        Module temperature low warning threshold  : 0.00 degrees C / 32.00 degrees F
        Module voltage high alarm threshold       : 3.5000 V
        Module voltage low alarm threshold        : 3.1000 V
        Module voltage high warning threshold     : 3.4500 V
        Module voltage low warning threshold      : 3.1500 V
        Laser rx power high alarm threshold       : 0.5011 mW / -3.00 dBm
        Laser rx power low alarm threshold        : 0.0049 mW / -23.10 dBm
        Laser rx power high warning threshold     : 0.5011 mW / -3.00 dBm
        Laser rx power low warning threshold      : 0.0049 mW / -23.10 dBm
root@BananaPi_BPi-R3 /root [#]#

13. SUMITOMO ELECTRIC SCP6894-GL-AW - 1.25G 1550nm 80km SM

root@BananaPi_BPi-R3 /root [#]# uname -a
Linux BananaPi_BPi-R3 6.1.77 #0 SMP Fri Feb 16 13:10:11 2024 aarch64 GNU/Linux

root@BananaPi_BPi-R3 /root [#]# dmesg | tail
...
[13399.202168] sfp sfp-2: module SumitomoElectric SCP6894-GL-AW    rev D    sn 790022D01138     dc 070128
[13406.675383] mt7530-mdio mdio-bus:1f sfp2: Link is Up - 1Gbps/Full - flow control rx/tx
[13406.683661] br-lan: port 5(sfp2) entered blocking state
[13406.688884] br-lan: port 5(sfp2) entered forwarding state
[13410.188458] net_ratelimit: 2 callbacks suppressed
[13410.188472] br-lan: received packet on sfp2 with own address as source address (addr:a6:bb:0f:ed:50:d6, vlan:0)
[13410.203321] br-lan: received packet on sfp2 with own address as source address (addr:a6:bb:0f:ed:50:d6, vlan:0)
[13410.213458] br-lan: received packet on sfp2 with own address as source address (addr:a6:bb:0f:ed:50:d6, vlan:0)

root@BananaPi_BPi-R3 /root [#]# ethtool sfp2
Settings for sfp2:
        Supported ports: [ FIBRE ]
        Supported link modes:   1000baseX/Full
        Supported pause frame use: Symmetric Receive-only
        Supports auto-negotiation: Yes
        Supported FEC modes: Not reported
        Advertised link modes:  1000baseX/Full
        Advertised pause frame use: Symmetric Receive-only
        Advertised auto-negotiation: Yes
        Advertised FEC modes: Not reported
        Link partner advertised link modes:  1000baseX/Full
        Link partner advertised pause frame use: Symmetric Receive-only
        Link partner advertised auto-negotiation: Yes
        Link partner advertised FEC modes: Not reported
        Speed: 1000Mb/s
        Duplex: Full
        Auto-negotiation: on
        Port: FIBRE
        PHYAD: 0
        Transceiver: internal
        Supports Wake-on: d
        Wake-on: d
        Link detected: yes
root@BananaPi_BPi-R3 /root [#]# ethtool -m sfp2
        Identifier                                : 0x03 (SFP)
        Extended identifier                       : 0x04 (GBIC/SFP defined by 2-wire interface ID)
        Connector                                 : 0x07 (LC)
        Transceiver codes                         : 0x00 0x00 0x00 0x02 0x00 0x00 0x00 0x00 0x00
        Transceiver type                          : Ethernet: 1000BASE-LX
        Encoding                                  : 0x01 (8B/10B)
        BR, Nominal                               : 1300MBd
        Rate identifier                           : 0x00 (unspecified)
        Length (SMF,km)                           : 80km
        Length (SMF)                              : 25500m
        Length (50um)                             : 550m
        Length (62.5um)                           : 550m
        Length (Copper)                           : 0m
        Length (OM3)                              : 0m
        Laser wavelength                          : 1550nm
        Vendor name                               : SumitomoElectric
        Vendor OUI                                : 00:00:5f
        Vendor PN                                 : SCP6894-GL-AW
        Vendor rev                                : D
        Option values                             : 0x00 0x1a
        Option                                    : RX_LOS implemented
        Option                                    : TX_FAULT implemented
        Option                                    : TX_DISABLE implemented
        BR margin, max                            : 0%
        BR margin, min                            : 0%
        Vendor SN                                 : 790022D01138
        Date code                                 : 070128
root@BananaPi_BPi-R3 /root [#]#

14. NORTEL GE LX/FC100 SM/FC200 NTTP06CFE6 05 - 1.25G 1310nm 10km SM

root@BananaPi_BPi-R3 /root [#]# uname -a
Linux BananaPi_BPi-R3 6.1.77 #0 SMP Fri Feb 16 13:10:11 2024 aarch64 GNU/Linux

root@BananaPi_BPi-R3 /root [#]# dmesg | tail
...
[13848.997580] sfp sfp-2: module WHTD             RTXM192-408NT    rev      sn BE0929640123     dc 090712
[13849.046710] hwmon hwmon6: temp1_input not attached to any thermal zone
[13853.403976] mt7530-mdio mdio-bus:1f sfp2: Link is Up - 1Gbps/Full - flow control rx/tx
[13853.412255] br-lan: port 5(sfp2) entered blocking state
[13853.417479] br-lan: port 5(sfp2) entered forwarding state
[13854.107706] br-lan: received packet on sfp2 with own address as source address (addr:a6:bb:0f:ed:50:d6, vlan:0)
[13854.117797] br-lan: received packet on sfp2 with own address as source address (addr:a6:bb:0f:ed:50:d6, vlan:0)
[13854.127865] br-lan: received packet on sfp2 with own address as source address (addr:a6:bb:0f:ed:50:d6, vlan:0)

root@BananaPi_BPi-R3 /root [#]# ethtool sfp2
Settings for sfp2:
        Supported ports: [ FIBRE ]
        Supported link modes:   1000baseX/Full
        Supported pause frame use: Symmetric Receive-only
        Supports auto-negotiation: Yes
        Supported FEC modes: Not reported
        Advertised link modes:  1000baseX/Full
        Advertised pause frame use: Symmetric Receive-only
        Advertised auto-negotiation: Yes
        Advertised FEC modes: Not reported
        Link partner advertised link modes:  1000baseX/Full
        Link partner advertised pause frame use: Symmetric Receive-only
        Link partner advertised auto-negotiation: Yes
        Link partner advertised FEC modes: Not reported
        Speed: 1000Mb/s
        Duplex: Full
        Auto-negotiation: on
        Port: FIBRE
        PHYAD: 0
        Transceiver: internal
        Supports Wake-on: d
        Wake-on: d
        Link detected: yes
root@BananaPi_BPi-R3 /root [#]# ethtool -m sfp2
        Identifier                                : 0x03 (SFP)
        Extended identifier                       : 0x04 (GBIC/SFP defined by 2-wire interface ID)
        Connector                                 : 0x07 (LC)
        Transceiver codes                         : 0x00 0x00 0x00 0x02 0x12 0x00 0x01 0x05 0x00
        Transceiver type                          : Ethernet: 1000BASE-LX
        Transceiver type                          : FC: long distance (L)
        Transceiver type                          : FC: Longwave laser (LC)
        Transceiver type                          : FC: Single Mode (SM)
        Transceiver type                          : FC: 200 MBytes/sec
        Transceiver type                          : FC: 100 MBytes/sec
        Encoding                                  : 0x03 (NRZ)
        BR, Nominal                               : 2100MBd
        Rate identifier                           : 0x00 (unspecified)
        Length (SMF,km)                           : 10km
        Length (SMF)                              : 10000m
        Length (50um)                             : 0m
        Length (62.5um)                           : 0m
        Length (Copper)                           : 0m
        Length (OM3)                              : 0m
        Laser wavelength                          : 1310nm
        Vendor name                               : WHTD
        Vendor OUI                                : 00:00:00
        Vendor PN                                 : RTXM192-408NT
        Vendor rev                                :
        Option values                             : 0x00 0x1a
        Option                                    : RX_LOS implemented
        Option                                    : TX_FAULT implemented
        Option                                    : TX_DISABLE implemented
        BR margin, max                            : 0%
        BR margin, min                            : 0%
        Vendor SN                                 : BE0929640123
        Date code                                 : 090712__
        Optical diagnostics support               : Yes
        Laser bias current                        : 8.128 mA
        Laser output power                        : 0.3112 mW / -5.07 dBm
        Receiver signal average optical power     : 0.3490 mW / -4.57 dBm
        Module temperature                        : 40.25 degrees C / 104.45 degrees F
        Module voltage                            : 3.3032 V
        Alarm/warning flags implemented           : Yes
        Laser bias current high alarm             : Off
        Laser bias current low alarm              : Off
        Laser bias current high warning           : Off
        Laser bias current low warning            : Off
        Laser output power high alarm             : Off
        Laser output power low alarm              : Off
        Laser output power high warning           : Off
        Laser output power low warning            : Off
        Module temperature high alarm             : Off
        Module temperature low alarm              : Off
        Module temperature high warning           : Off
        Module temperature low warning            : Off
        Module voltage high alarm                 : Off
        Module voltage low alarm                  : Off
        Module voltage high warning               : Off
        Module voltage low warning                : Off
        Laser rx power high alarm                 : Off
        Laser rx power low alarm                  : Off
        Laser rx power high warning               : Off
        Laser rx power low warning                : Off
        Laser bias current high alarm threshold   : 55.232 mA
        Laser bias current low alarm threshold    : 1.904 mA
        Laser bias current high warning threshold : 45.232 mA
        Laser bias current low warning threshold  : 3.808 mA
        Laser output power high alarm threshold   : 0.7943 mW / -1.00 dBm
        Laser output power low alarm threshold    : 0.0707 mW / -11.51 dBm
        Laser output power high warning threshold : 0.6309 mW / -2.00 dBm
        Laser output power low warning threshold  : 0.0891 mW / -10.50 dBm
        Module temperature high alarm threshold   : 93.00 degrees C / 199.40 degrees F
        Module temperature low alarm threshold    : -10.00 degrees C / 14.00 degrees F
        Module temperature high warning threshold : 88.00 degrees C / 190.40 degrees F
        Module temperature low warning threshold  : -5.00 degrees C / 23.00 degrees F
        Module voltage high alarm threshold       : 3.5650 V
        Module voltage low alarm threshold        : 3.0350 V
        Module voltage high warning threshold     : 3.5000 V
        Module voltage low warning threshold      : 3.1000 V
        Laser rx power high alarm threshold       : 0.7942 mW / -1.00 dBm
        Laser rx power low alarm threshold        : 0.0062 mW / -22.08 dBm
        Laser rx power high warning threshold     : 0.6309 mW / -2.00 dBm
        Laser rx power low warning threshold      : 0.0079 mW / -21.02 dBm
root@BananaPi_BPi-R3 /root [#]#

15. STRATOS SPLC-20-4-2M-BH-R6 - 1.25G 1310nm 10km SM

root@BananaPi_BPi-R3 /root [#]# uname -a
Linux BananaPi_BPi-R3 6.1.77 #0 SMP Fri Feb 16 13:10:11 2024 aarch64 GNU/Linux

root@BananaPi_BPi-R3 /root [#]# dmesg | tail
...
[14389.817550] sfp sfp-2: module StratosLightwave SPLC2042MBHR6    rev      sn G710341258       dc 07022900
[14404.032256] mt7530-mdio mdio-bus:1f sfp2: Link is Up - 1Gbps/Full - flow control rx/tx
[14404.040534] br-lan: port 5(sfp2) entered blocking state
[14404.045759] br-lan: port 5(sfp2) entered forwarding state
[14404.270289] net_ratelimit: 17 callbacks suppressed
[14404.270301] br-lan: received packet on sfp2 with own address as source address (addr:a6:bb:0f:ed:50:d6, vlan:0)
[14404.285273] br-lan: received packet on sfp2 with own address as source address (addr:a6:bb:0f:ed:50:d6, vlan:0)
[14404.295368] br-lan: received packet on sfp2 with own address as source address (addr:a6:bb:0f:ed:50:d6, vlan:0)

root@BananaPi_BPi-R3 /root [#]# ethtool sfp2
Settings for sfp2:
        Supported ports: [ FIBRE ]
        Supported link modes:   1000baseX/Full
        Supported pause frame use: Symmetric Receive-only
        Supports auto-negotiation: Yes
        Supported FEC modes: Not reported
        Advertised link modes:  1000baseX/Full
        Advertised pause frame use: Symmetric Receive-only
        Advertised auto-negotiation: Yes
        Advertised FEC modes: Not reported
        Link partner advertised link modes:  1000baseX/Full
        Link partner advertised pause frame use: Symmetric Receive-only
        Link partner advertised auto-negotiation: Yes
        Link partner advertised FEC modes: Not reported
        Speed: 1000Mb/s
        Duplex: Full
        Auto-negotiation: on
        Port: FIBRE
        PHYAD: 0
        Transceiver: internal
        Supports Wake-on: d
        Wake-on: d
        Link detected: yes
root@BananaPi_BPi-R3 /root [#]# ethtool -m sfp2
        Identifier                                : 0x03 (SFP)
        Extended identifier                       : 0x04 (GBIC/SFP defined by 2-wire interface ID)
        Connector                                 : 0x07 (LC)
        Transceiver codes                         : 0x00 0x00 0x00 0x02 0x12 0x00 0x01 0x01 0x00
        Transceiver type                          : Ethernet: 1000BASE-LX
        Transceiver type                          : FC: long distance (L)
        Transceiver type                          : FC: Longwave laser (LC)
        Transceiver type                          : FC: Single Mode (SM)
        Transceiver type                          : FC: 100 MBytes/sec
        Encoding                                  : 0x00 (unspecified)
        BR, Nominal                               : 1300MBd
        Rate identifier                           : 0x00 (unspecified)
        Length (SMF,km)                           : 10km
        Length (SMF)                              : 10000m
        Length (50um)                             : 0m
        Length (62.5um)                           : 0m
        Length (Copper)                           : 0m
        Length (OM3)                              : 0m
        Laser wavelength                          : 1310nm
        Vendor name                               : StratosLightwave
        Vendor OUI                                : 00:00:00
        Vendor PN                                 : SPLC2042MBHR6
        Vendor rev                                :
        Option values                             : 0x00 0x1a
        Option                                    : RX_LOS implemented
        Option                                    : TX_FAULT implemented
        Option                                    : TX_DISABLE implemented
        BR margin, max                            : 0%
        BR margin, min                            : 0%
        Vendor SN                                 : G710341258
        Date code                                 : 07022900
root@BananaPi_BPi-R3 /root [#]#

16. HUAWEI LTD1303-BC+1 - 1.25G-1310nm-10km-SM-ESFP

root@BananaPi_BPi-R3 /root [#]# uname -a
Linux BananaPi_BPi-R3 6.1.77 #0 SMP Fri Feb 16 13:10:11 2024 aarch64 GNU/Linux

root@BananaPi_BPi-R3 /root [#]# dmesg | tail
...
[  758.603399] sfp sfp-2: module Hisense          LTD1302-BC+1     rev V1.3 sn J3365052678      dc 160329
[  758.612896] mt7530-mdio mdio-bus:1f sfp2: switched to inband/1000base-x link mode
[  758.652561] hwmon hwmon5: temp1_input not attached to any thermal zone
[  770.024037] mt7530-mdio mdio-bus:1f sfp2: Link is Up - 1Gbps/Full - flow control rx/tx
[  770.032314] br-lan: port 5(sfp2) entered blocking state
[  770.037543] br-lan: port 5(sfp2) entered forwarding state
[  772.500365] br-lan: received packet on sfp2 with own address as source address (addr:a6:bb:0f:ed:50:d6, vlan:0)
[  773.539044] br-lan: received packet on sfp2 with own address as source address (addr:a6:bb:0f:ed:50:d6, vlan:0)
[  777.214978] br-lan: received packet on sfp2 with own address as source address (addr:a6:bb:0f:ed:50:d6, vlan:0)

root@BananaPi_BPi-R3 /root [#]# ethtool sfp2
Settings for sfp2:
        Supported ports: [ FIBRE ]
        Supported link modes:   1000baseX/Full
        Supported pause frame use: Symmetric Receive-only
        Supports auto-negotiation: Yes
        Supported FEC modes: Not reported
        Advertised link modes:  1000baseX/Full
        Advertised pause frame use: Symmetric Receive-only
        Advertised auto-negotiation: Yes
        Advertised FEC modes: Not reported
        Link partner advertised link modes:  1000baseX/Full
        Link partner advertised pause frame use: Symmetric Receive-only
        Link partner advertised auto-negotiation: Yes
        Link partner advertised FEC modes: Not reported
        Speed: 1000Mb/s
        Duplex: Full
        Auto-negotiation: on
        Port: FIBRE
        PHYAD: 0
        Transceiver: internal
        Supports Wake-on: d
        Wake-on: d
        Link detected: yes
root@BananaPi_BPi-R3 /root [#]# ethtool -m sfp2
        Identifier                                : 0x03 (SFP)
        Extended identifier                       : 0x04 (GBIC/SFP defined by 2-wire interface ID)
        Connector                                 : 0x07 (LC)
        Transceiver codes                         : 0x00 0x00 0x00 0x02 0x12 0x00 0x01 0x01 0x00
        Transceiver type                          : Ethernet: 1000BASE-LX
        Transceiver type                          : FC: long distance (L)
        Transceiver type                          : FC: Longwave laser (LC)
        Transceiver type                          : FC: Single Mode (SM)
        Transceiver type                          : FC: 100 MBytes/sec
        Encoding                                  : 0x03 (NRZ)
        BR, Nominal                               : 1200MBd
        Rate identifier                           : 0x00 (unspecified)
        Length (SMF,km)                           : 10km
        Length (SMF)                              : 10000m
        Length (50um)                             : 0m
        Length (62.5um)                           : 0m
        Length (Copper)                           : 0m
        Length (OM3)                              : 0m
        Laser wavelength                          : 1310nm
        Vendor name                               : Hisense
        Vendor OUI                                : 00:00:00
        Vendor PN                                 : LTD1302-BC+1
        Vendor rev                                : V1.3
        Option values                             : 0x00 0x1a
        Option                                    : RX_LOS implemented
        Option                                    : TX_FAULT implemented
        Option                                    : TX_DISABLE implemented
        BR margin, max                            : 0%
        BR margin, min                            : 0%
        Vendor SN                                 : J3365052678
        Date code                                 : 160329
        Optical diagnostics support               : Yes
        Laser bias current                        : 8.960 mA
        Laser output power                        : 0.3180 mW / -4.98 dBm
        Receiver signal average optical power     : 0.2617 mW / -5.82 dBm
        Module temperature                        : 35.16 degrees C / 95.28 degrees F
        Module voltage                            : 3.3800 V
        Alarm/warning flags implemented           : Yes
        Laser bias current high alarm             : Off
        Laser bias current low alarm              : Off
        Laser bias current high warning           : Off
        Laser bias current low warning            : Off
        Laser output power high alarm             : Off
        Laser output power low alarm              : Off
        Laser output power high warning           : Off
        Laser output power low warning            : Off
        Module temperature high alarm             : Off
        Module temperature low alarm              : Off
        Module temperature high warning           : Off
        Module temperature low warning            : Off
        Module voltage high alarm                 : Off
        Module voltage low alarm                  : Off
        Module voltage high warning               : Off
        Module voltage low warning                : Off
        Laser rx power high alarm                 : Off
        Laser rx power low alarm                  : Off
        Laser rx power high warning               : Off
        Laser rx power low warning                : Off
        Laser bias current high alarm threshold   : 70.000 mA
        Laser bias current low alarm threshold    : 0.000 mA
        Laser bias current high warning threshold : 65.000 mA
        Laser bias current low warning threshold  : 0.000 mA
        Laser output power high alarm threshold   : 0.7943 mW / -1.00 dBm
        Laser output power low alarm threshold    : 0.0794 mW / -11.00 dBm
        Laser output power high warning threshold : 0.5012 mW / -3.00 dBm
        Laser output power low warning threshold  : 0.1259 mW / -9.00 dBm
        Module temperature high alarm threshold   : 80.00 degrees C / 176.00 degrees F
        Module temperature low alarm threshold    : -10.00 degrees C / 14.00 degrees F
        Module temperature high warning threshold : 70.00 degrees C / 158.00 degrees F
        Module temperature low warning threshold  : 0.00 degrees C / 32.00 degrees F
        Module voltage high alarm threshold       : 3.6300 V
        Module voltage low alarm threshold        : 2.9700 V
        Module voltage high warning threshold     : 3.4650 V
        Module voltage low warning threshold      : 3.1350 V
        Laser rx power high alarm threshold       : 0.8000 mW / -0.97 dBm
        Laser rx power low alarm threshold        : 0.0063 mW / -22.01 dBm
        Laser rx power high warning threshold     : 0.5048 mW / -2.97 dBm
        Laser rx power low warning threshold      : 0.0100 mW / -20.00 dBm
root@BananaPi_BPi-R3 /root [#]#

17. OPNEXT TRF7765AALB2S3 - 1.25G 1550nm 80km SM

root@BananaPi_BPi-R3 /root [#]# uname -a
Linux BananaPi_BPi-R3 6.1.77 #0 SMP Fri Feb 16 13:10:11 2024 aarch64 GNU/Linux

root@BananaPi_BPi-R3 /root [#]# dmesg | tail
...
[ 1009.008141] sfp sfp-2: module OPNEXT INC       TRF7765AALB2S3   rev B1A  sn C08A54171        dc 080407
[ 1049.473182] mt7530-mdio mdio-bus:1f sfp2: Link is Up - 1Gbps/Full - flow control rx/tx
[ 1049.481461] br-lan: port 5(sfp2) entered blocking state
[ 1049.486685] br-lan: port 5(sfp2) entered forwarding state
[ 1057.470987] br-lan: received packet on sfp2 with own address as source address (addr:a6:bb:0f:ed:50:d6, vlan:0)
[ 1057.481157] br-lan: received packet on sfp2 with own address as source address (addr:a6:bb:0f:ed:50:d6, vlan:0)
[ 1057.491255] br-lan: received packet on sfp2 with own address as source address (addr:a6:bb:0f:ed:50:d6, vlan:0)

root@BananaPi_BPi-R3 /root [#]# ethtool sfp2
Settings for sfp2:
        Supported ports: [ FIBRE ]
        Supported link modes:   1000baseX/Full
        Supported pause frame use: Symmetric Receive-only
        Supports auto-negotiation: Yes
        Supported FEC modes: Not reported
        Advertised link modes:  1000baseX/Full
        Advertised pause frame use: Symmetric Receive-only
        Advertised auto-negotiation: Yes
        Advertised FEC modes: Not reported
        Link partner advertised link modes:  1000baseX/Full
        Link partner advertised pause frame use: Symmetric Receive-only
        Link partner advertised auto-negotiation: Yes
        Link partner advertised FEC modes: Not reported
        Speed: 1000Mb/s
        Duplex: Full
        Auto-negotiation: on
        Port: FIBRE
        PHYAD: 0
        Transceiver: internal
        Supports Wake-on: d
        Wake-on: d
        Link detected: yes
root@BananaPi_BPi-R3 /root [#]# ethtool -m sfp2
        Identifier                                : 0x03 (SFP)
        Extended identifier                       : 0x04 (GBIC/SFP defined by 2-wire interface ID)
        Connector                                 : 0x07 (LC)
        Transceiver codes                         : 0x00 0x00 0x00 0x02 0x80 0x10 0x01 0x01 0x00
        Transceiver type                          : Ethernet: 1000BASE-LX
        Transceiver type                          : FC: very long distance (V)
        Transceiver type                          : FC: Longwave laser (LL)
        Transceiver type                          : FC: Single Mode (SM)
        Transceiver type                          : FC: 100 MBytes/sec
        Encoding                                  : 0x01 (8B/10B)
        BR, Nominal                               : 1300MBd
        Rate identifier                           : 0x00 (unspecified)
        Length (SMF,km)                           : 80km
        Length (SMF)                              : 25500m
        Length (50um)                             : 0m
        Length (62.5um)                           : 0m
        Length (Copper)                           : 0m
        Length (OM3)                              : 0m
        Laser wavelength                          : 1550nm
        Vendor name                               : OPNEXT INC
        Vendor OUI                                : 00:0b:40
        Vendor PN                                 : TRF7765AALB2S3
        Vendor rev                                : B1A
        Option values                             : 0x00 0x1a
        Option                                    : RX_LOS implemented
        Option                                    : TX_FAULT implemented
        Option                                    : TX_DISABLE implemented
        BR margin, max                            : 0%
        BR margin, min                            : 0%
        Vendor SN                                 : C08A54171
        Date code                                 : 080407
root@BananaPi_BPi-R3 /root [#]#

18. RAD UN600024731 SFP-6 - 1.25G 1310nm 10km SM

root@BananaPi_BPi-R3 /root [#]# uname -a
Linux BananaPi_BPi-R3 6.1.77 #0 SMP Fri Feb 16 13:10:11 2024 aarch64 GNU/Linux

root@BananaPi_BPi-R3 /root [#]# dmesg | tail
...
[ 1732.273597] sfp sfp-2: module RAD Data Comm.   SFP-6            rev 1.1  sn EO140218072033   dc 140725
[ 1741.374404] mt7530-mdio mdio-bus:1f sfp2: Link is Up - 1Gbps/Full - flow control rx/tx
[ 1741.382680] br-lan: port 5(sfp2) entered blocking state
[ 1741.387904] br-lan: port 5(sfp2) entered forwarding state
[ 1746.915599] net_ratelimit: 1 callbacks suppressed
[ 1746.915613] br-lan: received packet on sfp2 with own address as source address (addr:a6:bb:0f:ed:50:d6, vlan:0)
[ 1746.930447] br-lan: received packet on sfp2 with own address as source address (addr:a6:bb:0f:ed:50:d6, vlan:0)
[ 1746.940563] br-lan: received packet on sfp2 with own address as source address (addr:a6:bb:0f:ed:50:d6, vlan:0)

root@BananaPi_BPi-R3 /root [#]# ethtool sfp2
Settings for sfp2:
        Supported ports: [ FIBRE ]
        Supported link modes:   1000baseX/Full
        Supported pause frame use: Symmetric Receive-only
        Supports auto-negotiation: Yes
        Supported FEC modes: Not reported
        Advertised link modes:  1000baseX/Full
        Advertised pause frame use: Symmetric Receive-only
        Advertised auto-negotiation: Yes
        Advertised FEC modes: Not reported
        Link partner advertised link modes:  1000baseX/Full
        Link partner advertised pause frame use: Symmetric Receive-only
        Link partner advertised auto-negotiation: Yes
        Link partner advertised FEC modes: Not reported
        Speed: 1000Mb/s
        Duplex: Full
        Auto-negotiation: on
        Port: FIBRE
        PHYAD: 0
        Transceiver: internal
        Supports Wake-on: d
        Wake-on: d
        Link detected: yes
root@BananaPi_BPi-R3 /root [#]# ethtool -m sfp2
        Identifier                                : 0x03 (SFP)
        Extended identifier                       : 0x04 (GBIC/SFP defined by 2-wire interface ID)
        Connector                                 : 0x07 (LC)
        Transceiver codes                         : 0x00 0x00 0x00 0x02 0x12 0x00 0x01 0x01 0x00
        Transceiver type                          : Ethernet: 1000BASE-LX
        Transceiver type                          : FC: long distance (L)
        Transceiver type                          : FC: Longwave laser (LC)
        Transceiver type                          : FC: Single Mode (SM)
        Transceiver type                          : FC: 100 MBytes/sec
        Encoding                                  : 0x01 (8B/10B)
        BR, Nominal                               : 1300MBd
        Rate identifier                           : 0x00 (unspecified)
        Length (SMF,km)                           : 10km
        Length (SMF)                              : 10000m
        Length (50um)                             : 0m
        Length (62.5um)                           : 0m
        Length (Copper)                           : 0m
        Length (OM3)                              : 0m
        Laser wavelength                          : 1310nm
        Vendor name                               : RAD Data Comm.
        Vendor OUI                                : 00:00:00
        Vendor PN                                 : SFP-6
        Vendor rev                                : 1.1
        Option values                             : 0x00 0x1a
        Option                                    : RX_LOS implemented
        Option                                    : TX_FAULT implemented
        Option                                    : TX_DISABLE implemented
        BR margin, max                            : 0%
        BR margin, min                            : 0%
        Vendor SN                                 : EO140218072033
        Date code                                 : 140725
root@BananaPi_BPi-R3 /root [#]#

Ciąg dalszy w następnym poście, tu już się nie mieści ... wink

Banana Pi BPI-R3 + SFP GPON ONT Nokia G-010S-A + LTE FIBOCOM L860-GL-16 (OpenWrt 25.12-SNAPSHOT, kernel 6.12.71)
Xiaomi AX3600 (OpenWrt 25.12-SNAPSHOT, kernel 6.12.71)
Xiaomi AX3000T (OpenWrt 25.12-SNAPSHOT, kernel 6.12.71)
All OpenWRT compilations from ASU by @Cezary

25 Odpowiedź przez Payti (edytowany przez Payti 2024-02-22 21:24:55)

  • Payti
  • Payti
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2012-01-05
  • Posty: 374

Odp: BPi-R3 i wkładka SFP GPON ONT oraz inne wkładki SFP 1Gbps, 2.5Gbps

Ciąg dalszy testów SFP 1Gbps z poprzedniego posta ....


19. ALCATEL (Sumitomo Electric) 3FE25773AA 01 SCP6F86-A6-CWH - 1.25G 850nm 300m MM LC/PC (wkładka multi-modowa, także działa)

root@BananaPi_BPi-R3 /root [#]# uname -a
Linux BananaPi_BPi-R3 6.1.77 #0 SMP Fri Feb 16 13:10:11 2024 aarch64 GNU/Linux

root@BananaPi_BPi-R3 /root [#]# dmesg | tail
...
[ 3709.623893] sfp sfp-2: module SumitomoElectric SCP6F86-A6-CWH   rev C    sn EXLGCN07090458   dc 070227
[ 3709.673034] hwmon hwmon5: temp1_input not attached to any thermal zone
[ 3804.638214] mt7530-mdio mdio-bus:1f sfp2: Link is Up - 1Gbps/Full - flow control rx/tx
[ 3804.646492] br-lan: port 5(sfp2) entered blocking state
[ 3804.651717] br-lan: port 5(sfp2) entered forwarding state
[ 3805.422106] br-lan: received packet on sfp2 with own address as source address (addr:a6:bb:0f:ed:50:d6, vlan:0)
[ 3805.432244] br-lan: received packet on sfp2 with own address as source address (addr:a6:bb:0f:ed:50:d6, vlan:0)
[ 3805.442387] br-lan: received packet on sfp2 with own address as source address (addr:a6:bb:0f:ed:50:d6, vlan:0)

root@BananaPi_BPi-R3 /root [#]# ethtool sfp2
Settings for sfp2:
        Supported ports: [ FIBRE ]
        Supported link modes:   1000baseX/Full
        Supported pause frame use: Symmetric Receive-only
        Supports auto-negotiation: Yes
        Supported FEC modes: Not reported
        Advertised link modes:  1000baseX/Full
        Advertised pause frame use: Symmetric Receive-only
        Advertised auto-negotiation: Yes
        Advertised FEC modes: Not reported
        Link partner advertised link modes:  1000baseX/Full
        Link partner advertised pause frame use: Symmetric Receive-only
        Link partner advertised auto-negotiation: Yes
        Link partner advertised FEC modes: Not reported
        Speed: 1000Mb/s
        Duplex: Full
        Auto-negotiation: on
        Port: FIBRE
        PHYAD: 0
        Transceiver: internal
        Supports Wake-on: d
        Wake-on: d
        Link detected: yes
root@BananaPi_BPi-R3 /root [#]# ethtool -m sfp2
        Identifier                                : 0x03 (SFP)
        Extended identifier                       : 0x04 (GBIC/SFP defined by 2-wire interface ID)
        Connector                                 : 0x07 (LC)
        Transceiver codes                         : 0x00 0x00 0x00 0x01 0x20 0x40 0x0c 0x05 0x00
        Transceiver type                          : Ethernet: 1000BASE-SX
        Transceiver type                          : FC: intermediate distance (I)
        Transceiver type                          : FC: Shortwave laser w/o OFC (SN)
        Transceiver type                          : FC: Multimode, 62.5um (M6)
        Transceiver type                          : FC: Multimode, 50um (M5)
        Transceiver type                          : FC: 200 MBytes/sec
        Transceiver type                          : FC: 100 MBytes/sec
        Encoding                                  : 0x01 (8B/10B)
        BR, Nominal                               : 2100MBd
        Rate identifier                           : 0x00 (unspecified)
        Length (SMF,km)                           : 0km
        Length (SMF)                              : 0m
        Length (50um)                             : 300m
        Length (62.5um)                           : 150m
        Length (Copper)                           : 0m
        Length (OM3)                              : 0m
        Laser wavelength                          : 850nm
        Vendor name                               : SumitomoElectric
        Vendor OUI                                : 00:00:5f
        Vendor PN                                 : SCP6F86-A6-CWH
        Vendor rev                                : C
        Option values                             : 0x00 0x1a
        Option                                    : RX_LOS implemented
        Option                                    : TX_FAULT implemented
        Option                                    : TX_DISABLE implemented
        BR margin, max                            : 0%
        BR margin, min                            : 0%
        Vendor SN                                 : EXLGCN07095408
        Date code                                 : 070927
        Optical diagnostics support               : Yes
        Laser bias current                        : 3.990 mA
        Laser output power                        : 0.2562 mW / -5.91 dBm
        Receiver signal average optical power     : 0.0010 mW / -20.10 dBm
        Module temperature                        : 36.57 degrees C / 97.83 degrees F
        Module voltage                            : 3.3281 V
        Alarm/warning flags implemented           : Yes
        Laser bias current high alarm             : Off
        Laser bias current low alarm              : Off
        Laser bias current high warning           : Off
        Laser bias current low warning            : Off
        Laser output power high alarm             : Off
        Laser output power low alarm              : Off
        Laser output power high warning           : Off
        Laser output power low warning            : Off
        Module temperature high alarm             : Off
        Module temperature low alarm              : Off
        Module temperature high warning           : Off
        Module temperature low warning            : Off
        Module voltage high alarm                 : Off
        Module voltage low alarm                  : Off
        Module voltage high warning               : Off
        Module voltage low warning                : Off
        Laser rx power high alarm                 : Off
        Laser rx power low alarm                  : On
        Laser rx power high warning               : Off
        Laser rx power low warning                : On
        Laser bias current high alarm threshold   : 10.000 mA
        Laser bias current low alarm threshold    : 1.000 mA
        Laser bias current high warning threshold : 9.000 mA
        Laser bias current low warning threshold  : 2.000 mA
        Laser output power high alarm threshold   : 0.8000 mW / -0.97 dBm
        Laser output power low alarm threshold    : 0.1000 mW / -10.00 dBm
        Laser output power high warning threshold : 0.6000 mW / -2.22 dBm
        Laser output power low warning threshold  : 0.2000 mW / -6.99 dBm
        Module temperature high alarm threshold   : 90.00 degrees C / 194.00 degrees F
        Module temperature low alarm threshold    : -40.00 degrees C / -40.00 degrees F
        Module temperature high warning threshold : 85.00 degrees C / 185.00 degrees F
        Module temperature low warning threshold  : -40.00 degrees C / -40.00 degrees F
        Module voltage high alarm threshold       : 4.0000 V
        Module voltage low alarm threshold        : 0.0000 V
        Module voltage high warning threshold     : 3.6449 V
        Module voltage low warning threshold      : 2.9550 V
        Laser rx power high alarm threshold       : 1.6000 mW / 2.04 dBm
        Laser rx power low alarm threshold        : 0.0100 mW / -20.00 dBm
        Laser rx power high warning threshold     : 1.0000 mW / 0.00 dBm
        Laser rx power low warning threshold      : 0.0200 mW / -16.99 dBm
root@BananaPi_BPi-R3 /root [#]#

20. Sumitomo Electric SCP6G94-L4-CME - 1.25G 1550nm 80km LC/PC

root@BananaPi_BPi-R3 /root [#]# uname -a
Linux BananaPi_BPi-R3 6.1.77 #0 SMP Fri Feb 16 13:10:11 2024 aarch64 GNU/Linux

root@BananaPi_BPi-R3 /root [#]# dmesg | tail
...
[ 6103.387405] sfp sfp-2: module SumitomoElectric SCP6G94-L4-CME   rev N    sn 38T732601121     dc 130830
[ 6103.396905] mt7530-mdio mdio-bus:1f sfp2: switched to inband/1000base-x link mode
[ 6103.436529] hwmon hwmon5: temp1_input not attached to any thermal zone
[ 6132.480187] mt7530-mdio mdio-bus:1f sfp2: Link is Up - 1Gbps/Full - flow control rx/tx
[ 6132.488465] br-lan: port 5(sfp2) entered blocking state
[ 6132.493687] br-lan: port 5(sfp2) entered forwarding state
[ 6135.497520] br-lan: received packet on sfp2 with own address as source address (addr:a2:1d:43:f7:0f:d6, vlan:0)
[ 6135.507691] br-lan: received packet on sfp2 with own address as source address (addr:a2:1d:43:f7:0f:d6, vlan:0)
[ 6135.517790] br-lan: received packet on sfp2 with own address as source address (addr:a2:1d:43:f7:0f:d6, vlan:0)

root@BananaPi_BPi-R3 /root [#]# ethtool sfp2
Settings for sfp2:
        Supported ports: [ FIBRE ]
        Supported link modes:   1000baseX/Full
        Supported pause frame use: Symmetric Receive-only
        Supports auto-negotiation: Yes
        Supported FEC modes: Not reported
        Advertised link modes:  1000baseX/Full
        Advertised pause frame use: Symmetric Receive-only
        Advertised auto-negotiation: Yes
        Advertised FEC modes: Not reported
        Link partner advertised link modes:  1000baseX/Full
        Link partner advertised pause frame use: Symmetric Receive-only
        Link partner advertised auto-negotiation: Yes
        Link partner advertised FEC modes: Not reported
        Speed: 1000Mb/s
        Duplex: Full
        Auto-negotiation: on
        Port: FIBRE
        PHYAD: 0
        Transceiver: internal
        Supports Wake-on: d
        Wake-on: d
        Link detected: yes
root@BananaPi_BPi-R3 /root [#]# ethtool -m sfp2
        Identifier                                : 0x03 (SFP)
        Extended identifier                       : 0x04 (GBIC/SFP defined by 2-wire interface ID)
        Connector                                 : 0x07 (LC)
        Transceiver codes                         : 0x00 0x00 0x00 0x02 0x00 0x00 0x00 0x00 0x00
        Transceiver type                          : Ethernet: 1000BASE-LX
        Encoding                                  : 0x01 (8B/10B)
        BR, Nominal                               : 1300MBd
        Rate identifier                           : 0x00 (unspecified)
        Length (SMF,km)                           : 80km
        Length (SMF)                              : 25500m
        Length (50um)                             : 0m
        Length (62.5um)                           : 0m
        Length (Copper)                           : 0m
        Length (OM3)                              : 0m
        Laser wavelength                          : 1550nm
        Vendor name                               : SumitomoElectric
        Vendor OUI                                : 00:00:5f
        Vendor PN                                 : SCP6G94-L4-CME
        Vendor rev                                : N
        Option values                             : 0x00 0x1a
        Option                                    : RX_LOS implemented
        Option                                    : TX_FAULT implemented
        Option                                    : TX_DISABLE implemented
        BR margin, max                            : 0%
        BR margin, min                            : 0%
        Vendor SN                                 : 38T732601121
        Date code                                 : 130830
        Optical diagnostics support               : Yes
        Laser bias current                        : 16.634 mA
        Laser output power                        : 1.7463 mW / 2.42 dBm
        Receiver signal average optical power     : 1.5631 mW / 1.94 dBm
        Module temperature                        : 43.81 degrees C / 110.86 degrees F
        Module voltage                            : 3.2999 V
        Alarm/warning flags implemented           : Yes
        Laser bias current high alarm             : Off
        Laser bias current low alarm              : Off
        Laser bias current high warning           : Off
        Laser bias current low warning            : Off
        Laser output power high alarm             : Off
        Laser output power low alarm              : Off
        Laser output power high warning           : Off
        Laser output power low warning            : Off
        Module temperature high alarm             : Off
        Module temperature low alarm              : Off
        Module temperature high warning           : Off
        Module temperature low warning            : Off
        Module voltage high alarm                 : Off
        Module voltage low alarm                  : Off
        Module voltage high warning               : Off
        Module voltage low warning                : Off
        Laser rx power high alarm                 : Off
        Laser rx power low alarm                  : Off
        Laser rx power high warning               : Off
        Laser rx power low warning                : Off
        Laser bias current high alarm threshold   : 70.000 mA
        Laser bias current low alarm threshold    : 0.000 mA
        Laser bias current high warning threshold : 60.000 mA
        Laser bias current low warning threshold  : 0.000 mA
        Laser output power high alarm threshold   : 6.3095 mW / 8.00 dBm
        Laser output power low alarm threshold    : 0.5011 mW / -3.00 dBm
        Laser output power high warning threshold : 3.9810 mW / 6.00 dBm
        Laser output power low warning threshold  : 0.7943 mW / -1.00 dBm
        Module temperature high alarm threshold   : 97.00 degrees C / 206.60 degrees F
        Module temperature low alarm threshold    : -45.00 degrees C / -49.00 degrees F
        Module temperature high warning threshold : 95.00 degrees C / 203.00 degrees F
        Module temperature low warning threshold  : -15.00 degrees C / 5.00 degrees F
        Module voltage high alarm threshold       : 4.0000 V
        Module voltage low alarm threshold        : 2.8000 V
        Module voltage high warning threshold     : 3.6000 V
        Module voltage low warning threshold      : 3.0000 V
        Laser rx power high alarm threshold       : 6.5535 mW / 8.16 dBm
        Laser rx power low alarm threshold        : 0.0000 mW / -inf dBm
        Laser rx power high warning threshold     : 6.5535 mW / 8.16 dBm
        Laser rx power low warning threshold      : 0.0000 mW / -inf dBm
root@BananaPi_BPi-R3 /root [#]#

21. NOKIA 3FE25774AA 01 - 1.25G 1310nm 10km LC/PC

root@BananaPi_BPi-R3 /root [#]# uname -a
Linux BananaPi_BPi-R3 6.1.78 #0 SMP Mon Feb 19 20:40:06 2024 aarch64 GNU/Linux

root@BananaPi_BPi-R3 /root [#]# dmesg | tail
...
[ 7476.514440] sfp sfp-2: module WTD              RTXM191-404      rev 3.0  sn WHTDCN17299294   dc 170915
[ 7476.563588] hwmon hwmon5: temp1_input not attached to any thermal zone
[ 7487.205756] mt7530-mdio mdio-bus:1f sfp2: Link is Up - 1Gbps/Full - flow control rx/tx
[ 7487.214033] br-lan: port 5(sfp2) entered blocking state
[ 7487.219254] br-lan: port 5(sfp2) entered forwarding state
[ 7491.580391] br-lan: received packet on sfp2 with own address as source address (addr:a2:1d:43:f7:0f:d6, vlan:0)
[ 7495.001056] br-lan: received packet on sfp2 with own address as source address (addr:a2:1d:43:f7:0f:d6, vlan:0)
[ 7495.011201] br-lan: received packet on sfp2 with own address as source address (addr:a2:1d:43:f7:0f:d6, vlan:0)

root@BananaPi_BPi-R3 /root [#]# ethtool sfp2
Settings for sfp2:
        Supported ports: [ FIBRE ]
        Supported link modes:   1000baseX/Full
        Supported pause frame use: Symmetric Receive-only
        Supports auto-negotiation: Yes
        Supported FEC modes: Not reported
        Advertised link modes:  1000baseX/Full
        Advertised pause frame use: Symmetric Receive-only
        Advertised auto-negotiation: Yes
        Advertised FEC modes: Not reported
        Link partner advertised link modes:  1000baseX/Full
        Link partner advertised pause frame use: Symmetric Receive-only
        Link partner advertised auto-negotiation: Yes
        Link partner advertised FEC modes: Not reported
        Speed: 1000Mb/s
        Duplex: Full
        Auto-negotiation: on
        Port: FIBRE
        PHYAD: 0
        Transceiver: internal
        Supports Wake-on: d
        Wake-on: d
        Link detected: yes
root@BananaPi_BPi-R3 /root [#]# ethtool -m sfp2
        Identifier                                : 0x03 (SFP)
        Extended identifier                       : 0x04 (GBIC/SFP defined by 2-wire interface ID)
        Connector                                 : 0x07 (LC)
        Transceiver codes                         : 0x00 0x00 0x00 0x02 0x42 0x00 0x01 0x00 0x00
        Transceiver type                          : Ethernet: 1000BASE-LX
        Transceiver type                          : FC: short distance (S)
        Transceiver type                          : FC: Longwave laser (LC)
        Transceiver type                          : FC: Single Mode (SM)
        Encoding                                  : 0x03 (NRZ)
        BR, Nominal                               : 1300MBd
        Rate identifier                           : 0x00 (unspecified)
        Length (SMF,km)                           : 10km
        Length (SMF)                              : 10000m
        Length (50um)                             : 0m
        Length (62.5um)                           : 0m
        Length (Copper)                           : 0m
        Length (OM3)                              : 0m
        Laser wavelength                          : 1310nm
        Vendor name                               : WTD
        Vendor OUI                                : 00:1c:ad
        Vendor PN                                 : RTXM191-404
        Vendor rev                                : 3.0
        Option values                             : 0x00 0x1a
        Option                                    : RX_LOS implemented
        Option                                    : TX_FAULT implemented
        Option                                    : TX_DISABLE implemented
        BR margin, max                            : 0%
        BR margin, min                            : 0%
        Vendor SN                                 : WHTDCN17299294
        Date code                                 : 170915
        Optical diagnostics support               : Yes
        Laser bias current                        : 12.824 mA
        Laser output power                        : 0.3204 mW / -4.94 dBm
        Receiver signal average optical power     : 0.3973 mW / -4.01 dBm
        Module temperature                        : 42.84 degrees C / 109.12 degrees F
        Module voltage                            : 3.3064 V
        Alarm/warning flags implemented           : Yes
        Laser bias current high alarm             : Off
        Laser bias current low alarm              : Off
        Laser bias current high warning           : Off
        Laser bias current low warning            : Off
        Laser output power high alarm             : Off
        Laser output power low alarm              : Off
        Laser output power high warning           : Off
        Laser output power low warning            : Off
        Module temperature high alarm             : Off
        Module temperature low alarm              : Off
        Module temperature high warning           : Off
        Module temperature low warning            : Off
        Module voltage high alarm                 : Off
        Module voltage low alarm                  : Off
        Module voltage high warning               : Off
        Module voltage low warning                : Off
        Laser rx power high alarm                 : Off
        Laser rx power low alarm                  : Off
        Laser rx power high warning               : On
        Laser rx power low warning                : Off
        Laser bias current high alarm threshold   : 62.720 mA
        Laser bias current low alarm threshold    : 2.272 mA
        Laser bias current high warning threshold : 52.720 mA
        Laser bias current low warning threshold  : 2.840 mA
        Laser output power high alarm threshold   : 0.5020 mW / -2.99 dBm
        Laser output power low alarm threshold    : 0.1998 mW / -6.99 dBm
        Laser output power high warning threshold : 0.3988 mW / -3.99 dBm
        Laser output power low warning threshold  : 0.2516 mW / -5.99 dBm
        Module temperature high alarm threshold   : 100.00 degrees C / 212.00 degrees F
        Module temperature low alarm threshold    : -45.00 degrees C / -49.00 degrees F
        Module temperature high warning threshold : 90.00 degrees C / 194.00 degrees F
        Module temperature low warning threshold  : -40.00 degrees C / -40.00 degrees F
        Module voltage high alarm threshold       : 3.6000 V
        Module voltage low alarm threshold        : 3.0000 V
        Module voltage high warning threshold     : 3.5000 V
        Module voltage low warning threshold      : 3.1000 V
        Laser rx power high alarm threshold       : 0.5011 mW / -3.00 dBm
        Laser rx power low alarm threshold        : 0.0099 mW / -20.04 dBm
        Laser rx power high warning threshold     : 0.2511 mW / -6.00 dBm
        Laser rx power low warning threshold      : 0.0199 mW / -17.01 dBm
root@BananaPi_BPi-R3 /root [#]#

22. ciena GE LX/FC100 SM/FC200 SM NTTP06CFE6 05 - 1.25G 1310nm 10km LC/PC

root@BananaPi_BPi-R3 /root [#]# uname -a
Linux BananaPi_BPi-R3 6.1.78 #0 SMP Mon Feb 19 20:40:06 2024 aarch64 GNU/Linux

root@BananaPi_BPi-R3 /root [#]# dmesg | tail
...
[ 8564.528718] sfp sfp-2: module WHTD             RTXM192-408NT    rev      sn WHTDCN1223012264 dc 120612
[ 8564.577836] hwmon hwmon5: temp1_input not attached to any thermal zone
[ 8573.891427] mt7530-mdio mdio-bus:1f sfp2: Link is Up - 1Gbps/Full - flow control rx/tx
[ 8573.899708] br-lan: port 5(sfp2) entered blocking state
[ 8573.904938] br-lan: port 5(sfp2) entered forwarding state
[ 8574.072475] br-lan: received packet on sfp2 with own address as source address (addr:a2:1d:43:f7:0f:d6, vlan:0)
[ 8574.082577] br-lan: received packet on sfp2 with own address as source address (addr:a2:1d:43:f7:0f:d6, vlan:0)
[ 8574.472003] br-lan: received packet on sfp2 with own address as source address (addr:a2:1d:43:f7:0f:d6, vlan:0)

root@BananaPi_BPi-R3 /root [#]# ethtool sfp2
Settings for sfp2:
        Supported ports: [ FIBRE ]
        Supported link modes:   1000baseX/Full
        Supported pause frame use: Symmetric Receive-only
        Supports auto-negotiation: Yes
        Supported FEC modes: Not reported
        Advertised link modes:  1000baseX/Full
        Advertised pause frame use: Symmetric Receive-only
        Advertised auto-negotiation: Yes
        Advertised FEC modes: Not reported
        Link partner advertised link modes:  1000baseX/Full
        Link partner advertised pause frame use: Symmetric Receive-only
        Link partner advertised auto-negotiation: Yes
        Link partner advertised FEC modes: Not reported
        Speed: 1000Mb/s
        Duplex: Full
        Auto-negotiation: on
        Port: FIBRE
        PHYAD: 0
        Transceiver: internal
        Supports Wake-on: d
        Wake-on: d
        Link detected: yes
root@BananaPi_BPi-R3 /root [#]# ethtool -m sfp2
        Identifier                                : 0x03 (SFP)
        Extended identifier                       : 0x04 (GBIC/SFP defined by 2-wire interface ID)
        Connector                                 : 0x07 (LC)
        Transceiver codes                         : 0x00 0x00 0x00 0x02 0x12 0x00 0x01 0x05 0x00
        Transceiver type                          : Ethernet: 1000BASE-LX
        Transceiver type                          : FC: long distance (L)
        Transceiver type                          : FC: Longwave laser (LC)
        Transceiver type                          : FC: Single Mode (SM)
        Transceiver type                          : FC: 200 MBytes/sec
        Transceiver type                          : FC: 100 MBytes/sec
        Encoding                                  : 0x03 (NRZ)
        BR, Nominal                               : 2100MBd
        Rate identifier                           : 0x00 (unspecified)
        Length (SMF,km)                           : 10km
        Length (SMF)                              : 10000m
        Length (50um)                             : 0m
        Length (62.5um)                           : 0m
        Length (Copper)                           : 0m
        Length (OM3)                              : 0m
        Laser wavelength                          : 1310nm
        Vendor name                               : WHTD
        Vendor OUI                                : 00:00:00
        Vendor PN                                 : RTXM192-408NT
        Vendor rev                                :
        Option values                             : 0x00 0x1a
        Option                                    : RX_LOS implemented
        Option                                    : TX_FAULT implemented
        Option                                    : TX_DISABLE implemented
        BR margin, max                            : 0%
        BR margin, min                            : 0%
        Vendor SN                                 : WHTDCN1223012264
        Date code                                 : 120612
        Optical diagnostics support               : Yes
        Laser bias current                        : 9.280 mA
        Laser output power                        : 0.3172 mW / -4.99 dBm
        Receiver signal average optical power     : 0.3469 mW / -4.60 dBm
        Module temperature                        : 43.34 degrees C / 110.02 degrees F
        Module voltage                            : 3.3080 V
        Alarm/warning flags implemented           : Yes
        Laser bias current high alarm             : Off
        Laser bias current low alarm              : Off
        Laser bias current high warning           : Off
        Laser bias current low warning            : Off
        Laser output power high alarm             : Off
        Laser output power low alarm              : Off
        Laser output power high warning           : Off
        Laser output power low warning            : Off
        Module temperature high alarm             : Off
        Module temperature low alarm              : Off
        Module temperature high warning           : Off
        Module temperature low warning            : Off
        Module voltage high alarm                 : Off
        Module voltage low alarm                  : Off
        Module voltage high warning               : Off
        Module voltage low warning                : Off
        Laser rx power high alarm                 : Off
        Laser rx power low alarm                  : Off
        Laser rx power high warning               : Off
        Laser rx power low warning                : Off
        Laser bias current high alarm threshold   : 56.656 mA
        Laser bias current low alarm threshold    : 2.082 mA
        Laser bias current high warning threshold : 46.656 mA
        Laser bias current low warning threshold  : 4.164 mA
        Laser output power high alarm threshold   : 0.7943 mW / -1.00 dBm
        Laser output power low alarm threshold    : 0.0707 mW / -11.51 dBm
        Laser output power high warning threshold : 0.6309 mW / -2.00 dBm
        Laser output power low warning threshold  : 0.0891 mW / -10.50 dBm
        Module temperature high alarm threshold   : 93.00 degrees C / 199.40 degrees F
        Module temperature low alarm threshold    : -10.00 degrees C / 14.00 degrees F
        Module temperature high warning threshold : 88.00 degrees C / 190.40 degrees F
        Module temperature low warning threshold  : -5.00 degrees C / 23.00 degrees F
        Module voltage high alarm threshold       : 3.5650 V
        Module voltage low alarm threshold        : 3.0350 V
        Module voltage high warning threshold     : 3.5000 V
        Module voltage low warning threshold      : 3.1000 V
        Laser rx power high alarm threshold       : 0.7942 mW / -1.00 dBm
        Laser rx power low alarm threshold        : 0.0062 mW / -22.08 dBm
        Laser rx power high warning threshold     : 0.6309 mW / -2.00 dBm
        Laser rx power low warning threshold      : 0.0079 mW / -21.02 dBm
root@BananaPi_BPi-R3 /root [#]#

23. WTD RTXM191-500 - 1.25G-1550nm-40km-SM-ESFP LC/PC

root@BananaPi_BPi-R3 /root [#]# uname -a
Linux BananaPi_BPi-R3 6.1.78 #0 SMP Mon Feb 19 20:40:06 2024 aarch64 GNU/Linux

root@BananaPi_BPi-R3 /root [#]# dmesg | tail
...
[ 9182.106219] sfp sfp-2: module WTD              RTXM191-500      rev 3.0  sn 100199880508     dc 120208
[ 9182.155317] hwmon hwmon5: temp1_input not attached to any thermal zone
[ 9193.077462] mt7530-mdio mdio-bus:1f sfp2: Link is Up - 1Gbps/Full - flow control rx/tx
[ 9193.085739] br-lan: port 5(sfp2) entered blocking state
[ 9193.090965] br-lan: port 5(sfp2) entered forwarding state
[ 9194.254620] br-lan: received packet on sfp2 with own address as source address (addr:a2:1d:43:f7:0f:d6, vlan:0)
[ 9194.384343] br-lan: received packet on sfp2 with own address as source address (addr:a2:1d:43:f7:0f:d6, vlan:0)
[ 9194.394511] br-lan: received packet on sfp2 with own address as source address (addr:a2:1d:43:f7:0f:d6, vlan:0)

root@BananaPi_BPi-R3 /root [#]# ethtool sfp2
Settings for sfp2:
        Supported ports: [ FIBRE ]
        Supported link modes:   1000baseX/Full
        Supported pause frame use: Symmetric Receive-only
        Supports auto-negotiation: Yes
        Supported FEC modes: Not reported
        Advertised link modes:  1000baseX/Full
        Advertised pause frame use: Symmetric Receive-only
        Advertised auto-negotiation: Yes
        Advertised FEC modes: Not reported
        Link partner advertised link modes:  1000baseX/Full
        Link partner advertised pause frame use: Symmetric Receive-only
        Link partner advertised auto-negotiation: Yes
        Link partner advertised FEC modes: Not reported
        Speed: 1000Mb/s
        Duplex: Full
        Auto-negotiation: on
        Port: FIBRE
        PHYAD: 0
        Transceiver: internal
        Supports Wake-on: d
        Wake-on: d
        Link detected: yes
root@BananaPi_BPi-R3 /root [#]# ethtool -m sfp2
        Identifier                                : 0x03 (SFP)
        Extended identifier                       : 0x04 (GBIC/SFP defined by 2-wire interface ID)
        Connector                                 : 0x07 (LC)
        Transceiver codes                         : 0x00 0x00 0x00 0x02 0x22 0x10 0x01 0x00 0x00
        Transceiver type                          : Ethernet: 1000BASE-LX
        Transceiver type                          : FC: intermediate distance (I)
        Transceiver type                          : FC: Longwave laser (LC)
        Transceiver type                          : FC: Longwave laser (LL)
        Transceiver type                          : FC: Single Mode (SM)
        Encoding                                  : 0x03 (NRZ)
        BR, Nominal                               : 1200MBd
        Rate identifier                           : 0x00 (unspecified)
        Length (SMF,km)                           : 40km
        Length (SMF)                              : 25500m
        Length (50um)                             : 0m
        Length (62.5um)                           : 0m
        Length (Copper)                           : 0m
        Length (OM3)                              : 0m
        Laser wavelength                          : 1550nm
        Vendor name                               : WTD
        Vendor OUI                                : 00:1c:ad
        Vendor PN                                 : RTXM191-500
        Vendor rev                                : 3.0
        Option values                             : 0x00 0x1a
        Option                                    : RX_LOS implemented
        Option                                    : TX_FAULT implemented
        Option                                    : TX_DISABLE implemented
        BR margin, max                            : 0%
        BR margin, min                            : 0%
        Vendor SN                                 : 100199880508
        Date code                                 : 120208
        Optical diagnostics support               : Yes
        Laser bias current                        : 8.976 mA
        Laser output power                        : 0.6352 mW / -1.97 dBm
        Receiver signal average optical power     : 0.4333 mW / -3.63 dBm
        Module temperature                        : 38.66 degrees C / 101.58 degrees F
        Module voltage                            : 3.3144 V
        Alarm/warning flags implemented           : Yes
        Laser bias current high alarm             : Off
        Laser bias current low alarm              : Off
        Laser bias current high warning           : Off
        Laser bias current low warning            : Off
        Laser output power high alarm             : Off
        Laser output power low alarm              : Off
        Laser output power high warning           : Off
        Laser output power low warning            : Off
        Module temperature high alarm             : Off
        Module temperature low alarm              : Off
        Module temperature high warning           : Off
        Module temperature low warning            : Off
        Module voltage high alarm                 : Off
        Module voltage low alarm                  : Off
        Module voltage high warning               : Off
        Module voltage low warning                : Off
        Laser rx power high alarm                 : Off
        Laser rx power low alarm                  : Off
        Laser rx power high warning               : Off
        Laser rx power low warning                : Off
        Laser bias current high alarm threshold   : 39.992 mA
        Laser bias current low alarm threshold    : 0.000 mA
        Laser bias current high warning threshold : 29.990 mA
        Laser bias current low warning threshold  : 0.000 mA
        Laser output power high alarm threshold   : 1.2594 mW / 1.00 dBm
        Laser output power low alarm threshold    : 0.3163 mW / -5.00 dBm
        Laser output power high warning threshold : 1.0003 mW / 0.00 dBm
        Laser output power low warning threshold  : 0.3982 mW / -4.00 dBm
        Module temperature high alarm threshold   : 85.00 degrees C / 185.00 degrees F
        Module temperature low alarm threshold    : -5.00 degrees C / 23.00 degrees F
        Module temperature high warning threshold : 75.00 degrees C / 167.00 degrees F
        Module temperature low warning threshold  : 0.00 degrees C / 32.00 degrees F
        Module voltage high alarm threshold       : 3.6000 V
        Module voltage low alarm threshold        : 3.0000 V
        Module voltage high warning threshold     : 3.5000 V
        Module voltage low warning threshold      : 3.1000 V
        Laser rx power high alarm threshold       : 0.5011 mW / -3.00 dBm
        Laser rx power low alarm threshold        : 0.0062 mW / -22.08 dBm
        Laser rx power high warning threshold     : 0.5011 mW / -3.00 dBm
        Laser rx power low warning threshold      : 0.0062 mW / -22.08 dBm
root@BananaPi_BPi-R3 /root [#]#

23. OCP TRPAG1ZXIBGS-HWS - 1.25G-1550nm-80km-SM-ESFP LC/PC

root@BananaPi_BPi-R3 /root [#]# uname -a
Linux BananaPi_BPi-R3 6.1.78 #0 SMP Mon Feb 19 20:40:06 2024 aarch64 GNU/Linux

root@BananaPi_BPi-R3 /root [#]# dmesg | tail
...
[ 9443.408566] sfp sfp-2: module OCP              TRPAG1ZXIBGS-HWS rev 0000 sn 6254213          dc 120109
[ 9443.457737] hwmon hwmon5: temp1_input not attached to any thermal zone
[ 9443.469295] mt7530-mdio mdio-bus:1f sfp2: Link is Up - 1Gbps/Full - flow control rx/tx
[ 9443.477558] br-lan: port 5(sfp2) entered blocking state
[ 9443.482779] br-lan: port 5(sfp2) entered forwarding state
[ 9444.302038] br-lan: received packet on sfp2 with own address as source address (addr:a2:1d:43:f7:0f:d6, vlan:0)
[ 9444.312215] br-lan: received packet on sfp2 with own address as source address (addr:a2:1d:43:f7:0f:d6, vlan:0)
[ 9444.322316] br-lan: received packet on sfp2 with own address as source address (addr:a2:1d:43:f7:0f:d6, vlan:0)

root@BananaPi_BPi-R3 /root [#]# ethtool sfp2
Settings for sfp2:
        Supported ports: [ FIBRE ]
        Supported link modes:   1000baseX/Full
        Supported pause frame use: Symmetric Receive-only
        Supports auto-negotiation: Yes
        Supported FEC modes: Not reported
        Advertised link modes:  1000baseX/Full
        Advertised pause frame use: Symmetric Receive-only
        Advertised auto-negotiation: Yes
        Advertised FEC modes: Not reported
        Link partner advertised link modes:  1000baseX/Full
        Link partner advertised pause frame use: Symmetric Receive-only
        Link partner advertised auto-negotiation: Yes
        Link partner advertised FEC modes: Not reported
        Speed: 1000Mb/s
        Duplex: Full
        Auto-negotiation: on
        Port: FIBRE
        PHYAD: 0
        Transceiver: internal
        Supports Wake-on: d
        Wake-on: d
        Link detected: yes
root@BananaPi_BPi-R3 /root [#]# ethtool -m sfp2
        Identifier                                : 0x03 (SFP)
        Extended identifier                       : 0x04 (GBIC/SFP defined by 2-wire interface ID)
        Connector                                 : 0x07 (LC)
        Transceiver codes                         : 0x00 0x00 0x00 0x02 0x00 0x00 0x00 0x00 0x00
        Transceiver type                          : Ethernet: 1000BASE-LX
        Encoding                                  : 0x01 (8B/10B)
        BR, Nominal                               : 1300MBd
        Rate identifier                           : 0x00 (unspecified)
        Length (SMF,km)                           : 80km
        Length (SMF)                              : 25500m
        Length (50um)                             : 0m
        Length (62.5um)                           : 0m
        Length (Copper)                           : 0m
        Length (OM3)                              : 0m
        Laser wavelength                          : 1550nm
        Vendor name                               : OCP
        Vendor OUI                                : 00:0a:1d
        Vendor PN                                 : TRPAG1ZXIBGS-HWS
        Vendor rev                                : 0000
        Option values                             : 0x00 0x1a
        Option                                    : RX_LOS implemented
        Option                                    : TX_FAULT implemented
        Option                                    : TX_DISABLE implemented
        BR margin, max                            : 0%
        BR margin, min                            : 0%
        Vendor SN                                 : 6254213
        Date code                                 : 120109
        Optical diagnostics support               : Yes
        Laser bias current                        : 22.204 mA
        Laser output power                        : 1.5044 mW / 1.77 dBm
        Receiver signal average optical power     : 0.5021 mW / -2.99 dBm
        Module temperature                        : 44.91 degrees C / 112.85 degrees F
        Module voltage                            : 3.3255 V
        Alarm/warning flags implemented           : Yes
        Laser bias current high alarm             : Off
        Laser bias current low alarm              : Off
        Laser bias current high warning           : Off
        Laser bias current low warning            : Off
        Laser output power high alarm             : Off
        Laser output power low alarm              : Off
        Laser output power high warning           : Off
        Laser output power low warning            : Off
        Module temperature high alarm             : Off
        Module temperature low alarm              : Off
        Module temperature high warning           : Off
        Module temperature low warning            : Off
        Module voltage high alarm                 : Off
        Module voltage low alarm                  : Off
        Module voltage high warning               : Off
        Module voltage low warning                : Off
        Laser rx power high alarm                 : Off
        Laser rx power low alarm                  : Off
        Laser rx power high warning               : Off
        Laser rx power low warning                : Off
        Laser bias current high alarm threshold   : 77.000 mA
        Laser bias current low alarm threshold    : 4.500 mA
        Laser bias current high warning threshold : 70.000 mA
        Laser bias current low warning threshold  : 5.500 mA
        Laser output power high alarm threshold   : 3.5481 mW / 5.50 dBm
        Laser output power low alarm threshold    : 0.8913 mW / -0.50 dBm
        Laser output power high warning threshold : 3.1623 mW / 5.00 dBm
        Laser output power low warning threshold  : 1.0000 mW / 0.00 dBm
        Module temperature high alarm threshold   : 87.00 degrees C / 188.60 degrees F
        Module temperature low alarm threshold    : -8.00 degrees C / 17.60 degrees F
        Module temperature high warning threshold : 83.00 degrees C / 181.40 degrees F
        Module temperature low warning threshold  : -7.00 degrees C / 19.40 degrees F
        Module voltage high alarm threshold       : 3.5100 V
        Module voltage low alarm threshold        : 3.1000 V
        Module voltage high warning threshold     : 3.4950 V
        Module voltage low warning threshold      : 3.1150 V
        Laser rx power high alarm threshold       : 0.7079 mW / -1.50 dBm
        Laser rx power low alarm threshold        : 0.0020 mW / -26.99 dBm
        Laser rx power high warning threshold     : 0.6310 mW / -2.00 dBm
        Laser rx power low warning threshold      : 0.0025 mW / -26.02 dBm
root@BananaPi_BPi-R3 /root [#]#

Wkładki SFP, które NIE działają w BPi-R3

1. HG Genuine MXPD-033S - 155M-1310nm-15km-SM-ESFP  LC/PC

root@BananaPi_BPi-R3 /root [#]# uname -a
Linux BananaPi_BPi-R3 6.1.77 #0 SMP Fri Feb 16 13:10:11 2024 aarch64 GNU/Linux

root@BananaPi_BPi-R3 /root [#]# dmesg | tail
...
[24593.593476] sfp sfp-2: module HG GENUINE       MXPD-033S        rev  sn MA11070111803    dc 111214
[24593.602613] mt7530-mdio mdio-bus:1f sfp2: unsupported SFP module: no common interface modes
[24593.652632] hwmon hwmon5: temp1_input not attached to any thermal zone

root@BananaPi_BPi-R3 /root [#]# ethtool sfp2
Settings for sfp2:
        Supported ports: [ FIBRE ]
        Supported link modes:   1000baseX/Full
        Supported pause frame use: Symmetric Receive-only
        Supports auto-negotiation: Yes
        Supported FEC modes: Not reported
        Advertised link modes:  1000baseX/Full
        Advertised pause frame use: Symmetric Receive-only
        Advertised auto-negotiation: Yes
        Advertised FEC modes: Not reported
        Speed: Unknown!
        Duplex: Unknown! (255)
        Auto-negotiation: on
        Port: FIBRE
        PHYAD: 0
        Transceiver: internal
        Supports Wake-on: d
        Wake-on: d
        Link detected: no
root@BananaPi_BPi-R3 /root [#]# ethtool -m sfp2
        Identifier                                : 0x03 (SFP)
        Extended identifier                       : 0x04 (GBIC/SFP defined by 2-wire interface ID)
        Connector                                 : 0x07 (LC)
        Transceiver codes                         : 0x00 0x10 0x02 0x00 0x00 0x00 0x00 0x00 0x00
        Transceiver type                          : SONET: SONET reach specifier bit 1
        Transceiver type                          : SONET: OC-3, single mode, inter. reach
        Encoding                                  : 0x05 (SONET Scrambled)
        BR, Nominal                               : 100MBd
        Rate identifier                           : 0x00 (unspecified)
        Length (SMF,km)                           : 15km
        Length (SMF)                              : 15000m
        Length (50um)                             : 0m
        Length (62.5um)                           : 0m
        Length (Copper)                           : 0m
        Length (OM3)                              : 0m
        Laser wavelength                          : 1310nm
        Vendor name                               : HG GENUINE
        Vendor OUI                                : 00:00:00
        Vendor PN                                 : MXPD-033S
        Vendor rev                                : ____
        Option values                             : 0x00 0x1a
        Option                                    : RX_LOS implemented
        Option                                    : TX_FAULT implemented
        Option                                    : TX_DISABLE implemented
        BR margin, max                            : 0%
        BR margin, min                            : 0%
        Vendor SN                                 : MA11070111803
        Date code                                 : 111214
        Optical diagnostics support               : Yes
        Laser bias current                        : 6.960 mA
        Laser output power                        : 0.0854 mW / -10.69 dBm
        Receiver signal average optical power     : 0.1006 mW / -9.97 dBm
        Module temperature                        : 45.16 degrees C / 113.28 degrees F
        Module voltage                            : 3.3280 V
        Alarm/warning flags implemented           : Yes
        Laser bias current high alarm             : Off
        Laser bias current low alarm              : Off
        Laser bias current high warning           : Off
        Laser bias current low warning            : Off
        Laser output power high alarm             : Off
        Laser output power low alarm              : Off
        Laser output power high warning           : Off
        Laser output power low warning            : Off
        Module temperature high alarm             : Off
        Module temperature low alarm              : Off
        Module temperature high warning           : Off
        Module temperature low warning            : Off
        Module voltage high alarm                 : Off
        Module voltage low alarm                  : Off
        Module voltage high warning               : Off
        Module voltage low warning                : Off
        Laser rx power high alarm                 : Off
        Laser rx power low alarm                  : Off
        Laser rx power high warning               : Off
        Laser rx power low warning                : Off
        Laser bias current high alarm threshold   : 24.030 mA
        Laser bias current low alarm threshold    : 1.602 mA
        Laser bias current high warning threshold : 20.024 mA
        Laser bias current low warning threshold  : 1.602 mA
        Laser output power high alarm threshold   : 0.1697 mW / -7.70 dBm
        Laser output power low alarm threshold    : 0.0426 mW / -13.71 dBm
        Laser output power high warning threshold : 0.1348 mW / -8.70 dBm
        Laser output power low warning threshold  : 0.0536 mW / -12.71 dBm
        Module temperature high alarm threshold   : 80.00 degrees C / 176.00 degrees F
        Module temperature low alarm threshold    : -10.00 degrees C / 14.00 degrees F
        Module temperature high warning threshold : 75.00 degrees C / 167.00 degrees F
        Module temperature low warning threshold  : -5.00 degrees C / 23.00 degrees F
        Module voltage high alarm threshold       : 3.7000 V
        Module voltage low alarm threshold        : 2.8500 V
        Module voltage high warning threshold     : 3.6300 V
        Module voltage low warning threshold      : 2.9700 V
        Laser rx power high alarm threshold       : 0.1563 mW / -8.06 dBm
        Laser rx power low alarm threshold        : 0.0016 mW / -27.96 dBm
        Laser rx power high warning threshold     : 0.1563 mW / -8.06 dBm
        Laser rx power low warning threshold      : 0.0016 mW / -27.96 dBm
root@BananaPi_BPi-R3 /root [#]#

2. WTD RTXM139-400 - 155M-1310nm-15km-SM-ESFP  LC/PC

root@BananaPi_BPi-R3 /root [#]# uname -a
Linux BananaPi_BPi-R3 6.1.77 #0 SMP Fri Feb 16 13:10:11 2024 aarch64 GNU/Linux

root@BananaPi_BPi-R3 /root [#]# dmesg | tail
...
[ 8524.963793] sfp sfp-2: module WTD              RTXM139-400      rev 3.0  sn 112106420509     dc 110530
[ 8524.973281] mt7530-mdio mdio-bus:1f sfp2: unsupported SFP module: no common interface modes
[ 8525.012696] hwmon hwmon5: temp1_input not attached to any thermal zone

root@BananaPi_BPi-R3 /root [#]# ethtool sfp2
Settings for sfp2:
        Supported ports: [ MII ]
        Supported link modes:   2500baseX/Full
        Supported pause frame use: Symmetric Receive-only
        Supports auto-negotiation: Yes
        Supported FEC modes: Not reported
        Advertised link modes:  2500baseX/Full
        Advertised pause frame use: Symmetric Receive-only
        Advertised auto-negotiation: Yes
        Advertised FEC modes: Not reported
        Speed: 2500Mb/s
        Duplex: Full
        Auto-negotiation: on
        Port: MII
        PHYAD: 0
        Transceiver: internal
        Supports Wake-on: d
        Wake-on: d
        Link detected: no
root@BananaPi_BPi-R3 /root [#]# ethtool -m sfp2
        Identifier                                : 0x03 (SFP)
        Extended identifier                       : 0x04 (GBIC/SFP defined by 2-wire interface ID)
        Connector                                 : 0x07 (LC)
        Transceiver codes                         : 0x00 0x10 0x02 0x10 0x00 0x00 0x00 0x00 0x00
        Transceiver type                          : SONET: SONET reach specifier bit 1
        Transceiver type                          : SONET: OC-3, single mode, inter. reach
        Transceiver type                          : Ethernet: 100BASE-LX/LX10
        Encoding                                  : 0x03 (NRZ)
        BR, Nominal                               : 100MBd
        Rate identifier                           : 0x00 (unspecified)
        Length (SMF,km)                           : 15km
        Length (SMF)                              : 15000m
        Length (50um)                             : 0m
        Length (62.5um)                           : 0m
        Length (Copper)                           : 0m
        Length (OM3)                              : 0m
        Laser wavelength                          : 1310nm
        Vendor name                               : WTD
        Vendor OUI                                : 00:1c:ad
        Vendor PN                                 : RTXM139-400
        Vendor rev                                : 3.0
        Option values                             : 0x00 0x1a
        Option                                    : RX_LOS implemented
        Option                                    : TX_FAULT implemented
        Option                                    : TX_DISABLE implemented
        BR margin, max                            : 70%
        BR margin, min                            : 90%
        Vendor SN                                 : 112106420509
        Date code                                 : 110530
        Optical diagnostics support               : Yes
        Laser bias current                        : 6.440 mA
        Laser output power                        : 0.0888 mW / -10.52 dBm
        Receiver signal average optical power     : 0.0839 mW / -10.76 dBm
        Module temperature                        : 44.91 degrees C / 112.83 degrees F
        Module voltage                            : 3.3280 V
        Alarm/warning flags implemented           : Yes
        Laser bias current high alarm             : Off
        Laser bias current low alarm              : Off
        Laser bias current high warning           : Off
        Laser bias current low warning            : Off
        Laser output power high alarm             : Off
        Laser output power low alarm              : Off
        Laser output power high warning           : Off
        Laser output power low warning            : Off
        Module temperature high alarm             : Off
        Module temperature low alarm              : Off
        Module temperature high warning           : Off
        Module temperature low warning            : Off
        Module voltage high alarm                 : Off
        Module voltage low alarm                  : Off
        Module voltage high warning               : Off
        Module voltage low warning                : Off
        Laser rx power high alarm                 : Off
        Laser rx power low alarm                  : Off
        Laser rx power high warning               : Off
        Laser rx power low warning                : Off
        Laser bias current high alarm threshold   : 33.512 mA
        Laser bias current low alarm threshold    : 0.000 mA
        Laser bias current high warning threshold : 23.512 mA
        Laser bias current low warning threshold  : 0.000 mA
        Laser output power high alarm threshold   : 0.1787 mW / -7.48 dBm
        Laser output power low alarm threshold    : 0.0449 mW / -13.48 dBm
        Laser output power high warning threshold : 0.1420 mW / -8.48 dBm
        Laser output power low warning threshold  : 0.0565 mW / -12.48 dBm
        Module temperature high alarm threshold   : 85.00 degrees C / 185.00 degrees F
        Module temperature low alarm threshold    : -5.00 degrees C / 23.00 degrees F
        Module temperature high warning threshold : 75.00 degrees C / 167.00 degrees F
        Module temperature low warning threshold  : 0.00 degrees C / 32.00 degrees F
        Module voltage high alarm threshold       : 3.6000 V
        Module voltage low alarm threshold        : 3.0000 V
        Module voltage high warning threshold     : 3.5000 V
        Module voltage low warning threshold      : 3.1000 V
        Laser rx power high alarm threshold       : 0.1584 mW / -8.00 dBm
        Laser rx power low alarm threshold        : 0.0015 mW / -28.24 dBm
        Laser rx power high warning threshold     : 0.1584 mW / -8.00 dBm
        Laser rx power low warning threshold      : 0.0015 mW / -28.24 dBm
root@BananaPi_BPi-R3 /root [#]#

3. GBC PHOTONICS SF-CP100C-GP - 10/100/1000Base-T RJ45 100m

root@BananaPi_BPi-R3 /root [#]# uname -a
Linux BananaPi_BPi-R3 6.1.77 #0 SMP Fri Feb 16 13:10:11 2024 aarch64 GNU/Linux

root@BananaPi_BPi-R3 /root [#]# dmesg | tail
...
[24940.472376] sfp sfp-2: module OEM              SF-CP100C-GP     rev A    sn TD9U888267       dc 131112
[24940.567646] mt7530-mdio mdio-bus:1f sfp2: validation with support 00000000,00000000,00000000 failed: -EINVAL
[24940.577556] sfp sfp-2: sfp_add_phy failed: -EINVAL

root@BananaPi_BPi-R3 /root [#]# ethtool sfp2
Settings for sfp2:
        Supported ports: [ FIBRE ]
        Supported link modes:   1000baseX/Full
        Supported pause frame use: Symmetric Receive-only
        Supports auto-negotiation: Yes
        Supported FEC modes: Not reported
        Advertised link modes:  1000baseX/Full
        Advertised pause frame use: Symmetric Receive-only
        Advertised auto-negotiation: Yes
        Advertised FEC modes: Not reported
        Speed: Unknown!
        Duplex: Unknown! (255)
        Auto-negotiation: on
        Port: FIBRE
        PHYAD: 0
        Transceiver: internal
        Supports Wake-on: d
        Wake-on: d
        Link detected: no
root@BananaPi_BPi-R3 /root [#]# ethtool -m sfp2
        Identifier                                : 0x03 (SFP)
        Extended identifier                       : 0x04 (GBIC/SFP defined by 2-wire interface ID)
        Connector                                 : 0x07 (LC)
        Transceiver codes                         : 0x00 0x00 0x00 0x08 0x00 0x00 0x00 0x00 0x00
        Transceiver type                          : Ethernet: 1000BASE-T
        Encoding                                  : 0x01 (8B/10B)
        BR, Nominal                               : 1300MBd
        Rate identifier                           : 0x00 (unspecified)
        Length (SMF,km)                           : 0km
        Length (SMF)                              : 0m
        Length (50um)                             : 0m
        Length (62.5um)                           : 0m
        Length (Copper)                           : 100m
        Length (OM3)                              : 0m
        Laser wavelength                          : 0nm
        Vendor name                               : OEM
        Vendor OUI                                : 00:53:4f
        Vendor PN                                 : SF-CP100C-GP
        Vendor rev                                : A
        Option values                             : 0x00 0x00
        BR margin, max                            : 0%
        BR margin, min                            : 0%
        Vendor SN                                 : TD9U888267
        Date code                                 : 131112
root@BananaPi_BPi-R3 /root [#]#

Podsumowując -> jestem pod wrażeniem, duża ilość dostępnych wkładek SFP, zróżnicowanych producentów 2.5Gbps i 1Gbps Ethernet działa poprawnie w BPi-R3 wink Generalnie nie działają wkładki 100Mbit/s, pomimo że obsługują Ethernet.

Kolejne przetestowane wkładki SFP niebawem jak będę miał dostępne wink

Banana Pi BPI-R3 + SFP GPON ONT Nokia G-010S-A + LTE FIBOCOM L860-GL-16 (OpenWrt 25.12-SNAPSHOT, kernel 6.12.71)
Xiaomi AX3600 (OpenWrt 25.12-SNAPSHOT, kernel 6.12.71)
Xiaomi AX3000T (OpenWrt 25.12-SNAPSHOT, kernel 6.12.71)
All OpenWRT compilations from ASU by @Cezary