ambrozy5 napisał/a:Może czas na zmianę? Kilka sztuk po znajomych zamontowałem ale jak się zaczęły problemy z nandem to pozbyłem się ich, używki wtedy kupiłem więc nieco zużyte już na starcie były.
pewnie z tego samego żródełka co całe forum, i ja.
robie z nich dummy AP ;p z resztą, dopiero co kupiłem "nowy" router LTE 4G kat 16 na tym samym mcu, więc .. 
wracając do tematu, strzeliłem jak na wiki wariant na 3700, i nie wstało radio 5g ?
[ 0.000000] Linux version 6.12.94 (cezary@eko.one.pl) (mipsel-openwrt-linux-musl-gcc (OpenWrt GCC 14.3.0 r32355-02f9e71dd2) 14.3.0, GNU ld (GNU Binutils) 2.44) #0 SMP Thu Jul 30 13:53:31 2026
[ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
[ 0.000000] printk: legacy bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[ 0.000000] MIPS: machine is Netgear WNDR3700 v5
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] VPE topology {2} total 2
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] OF: reserved mem: Reserved memory: No reserved-memory node in the DT
[ 0.000000] percpu: Embedded 13 pages/cpu s22928 r8192 d22128 u53248
[ 0.000000] pcpu-alloc: s22928 r8192 d22128 u53248 alloc=13*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[ 0.000000] Writing ErrCtl register=00004009
[ 0.000000] Readback ErrCtl register=00004009
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32768
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] RCU Tasks Trace: Setting shift to 1 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=2.
[ 0.000000] NR_IRQS: 256
[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns
[ 0.000004] sched_clock: 64 bits at 880MHz, resolution 1ns, wraps every 4398046511103ns
[ 0.016029] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688)
[ 0.088264] pid_max: default: 32768 minimum: 301
[ 0.107147] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.121559] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.147044] rcu: Hierarchical SRCU implementation.
[ 0.156452] rcu: Max phase no-delay instances is 1000.
[ 0.167364] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level
[ 0.184006] smp: Bringing up secondary CPUs ...
[ 0.193874] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.193905] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.193921] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.194051] CPU1 revision is: 0001992f (MIPS 1004Kc)
[ 0.253704] smp: Brought up 1 node, 2 CPUs
[ 0.312296] Memory: 116780K/131072K available (8774K kernel code, 657K rwdata, 1088K rodata, 1244K init, 236K bss, 13452K reserved, 0K cma-reserved)
[ 0.345533] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.365053] futex hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.384236] pinctrl core: initialized pinctrl subsystem
[ 0.397590] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.410164] thermal_sys: Registered thermal governor 'step_wise'
[ 0.412833] /pinctrl: Fixed dependency cycle(s) with /pinctrl/pinctrl0
[ 0.442060] FPU Affinity set after 11720 emulations
[ 0.457733] clocksource: Switched to clocksource GIC
[ 0.477531] NET: Registered PF_INET protocol family
[ 0.487402] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.503205] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 0.519768] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.535112] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.550327] TCP bind hash table entries: 1024 (order: 2, 16384 bytes, linear)
[ 0.564556] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.577584] MPTCP token hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.592202] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.605110] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.619978] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.631197] PCI: CLS 0 bytes, default 32
[ 0.642261] workingset: timestamp_bits=14 max_order=15 bucket_order=1
[ 0.657130] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.668641] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.692874] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 0.711025] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 0.722539] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 0.734072] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 0.745760] mt7621-pci 1e140000.pcie: host bridge /pcie@1e140000 ranges:
[ 0.759069] mt7621-pci 1e140000.pcie: No bus range found for /pcie@1e140000, using [bus 00-ff]
[ 0.776492] mt7621-pci 1e140000.pcie: MEM 0x0060000000..0x006fffffff -> 0x0060000000
[ 0.792715] mt7621-pci 1e140000.pcie: IO 0x001e160000..0x001e16ffff -> 0x0000000000
[ 1.137704] mt7621-pci 1e140000.pcie: pcie0 no card, disable it (RST & CLK)
[ 1.151502] mt7621-pci 1e140000.pcie: pcie1 no card, disable it (RST & CLK)
[ 1.165301] mt7621-pci 1e140000.pcie: PCIE2 enabled
[ 1.175175] PCI coherence region base: 0x60000000, mask/settings: 0xf0000002
[ 1.189260] mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00
[ 1.201845] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 1.212670] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
[ 1.226343] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
[ 1.238840] pci 0000:00:02.0: [0e8d:0801] type 01 class 0x060400 PCIe Root Port
[ 1.253302] pci 0000:00:02.0: BAR 0 [mem 0x00000000-0x7fffffff]
[ 1.265035] pci 0000:00:02.0: BAR 1 [mem 0x00000000-0x0000ffff]
[ 1.276781] pci 0000:00:02.0: PCI bridge to [bus 00]
[ 1.286624] pci 0000:00:02.0: bridge window [io 0x0000-0x0fff]
[ 1.298718] pci 0000:00:02.0: bridge window [mem 0x00000000-0x000fffff]
[ 1.312207] pci 0000:00:02.0: bridge window [mem 0x00000000-0x000fffff pref]
[ 1.326615] pci 0000:00:02.0: supports D1
[ 1.334489] pci 0000:00:02.0: PME# supported from D0 D1 D3hot
[ 1.348137] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 1.364304] pci 0000:01:00.0: [14c3:7603] type 00 class 0x028000 PCIe Endpoint
[ 1.378641] pci 0000:01:00.0: BAR 0 [mem 0x00000000-0x000fffff]
[ 1.390487] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[ 1.402872] pci 0000:00:02.0: PCI bridge to [bus 01-ff]
[ 1.413216] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 1.426356] pci 0000:00:02.0: BAR 0 [mem size 0x80000000]: can't assign; no space
[ 1.441173] pci 0000:00:02.0: BAR 0 [mem size 0x80000000]: failed to assign
[ 1.454999] pci 0000:00:02.0: bridge window [mem 0x60000000-0x600fffff]: assigned
[ 1.469873] pci 0000:00:02.0: bridge window [mem 0x60100000-0x601fffff pref]: assigned
[ 1.485583] pci 0000:00:02.0: BAR 1 [mem 0x60200000-0x6020ffff]: assigned
[ 1.499065] pci 0000:00:02.0: bridge window [io 0x0000-0x0fff]: assigned
[ 1.512541] pci 0000:01:00.0: BAR 0 [mem 0x60000000-0x600fffff]: assigned
[ 1.526008] pci 0000:00:02.0: PCI bridge to [bus 01]
[ 1.535864] pci 0000:00:02.0: bridge window [io 0x0000-0x0fff]
[ 1.547951] pci 0000:00:02.0: bridge window [mem 0x60000000-0x600fffff]
[ 1.561443] pci 0000:00:02.0: bridge window [mem 0x60100000-0x601fffff pref]
[ 1.575771] pci_bus 0000:00: Some PCI device resources are unassigned, try booting with pci=realloc
[ 1.593745] pci_bus 0000:00: resource 4 [mem 0x60000000-0x6fffffff]
[ 1.606185] pci_bus 0000:00: resource 5 [io 0x0000-0xffff]
[ 1.617239] pci_bus 0000:01: resource 0 [io 0x0000-0x0fff]
[ 1.628311] pci_bus 0000:01: resource 1 [mem 0x60000000-0x600fffff]
[ 1.640746] pci_bus 0000:01: resource 2 [mem 0x60100000-0x601fffff pref]
[ 1.656205] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 1.676823] printk: legacy console [ttyS0] disabled
[ 1.687464] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 14, base_baud = 3125000) is a 16550A
[ 1.705579] printk: legacy console [ttyS0] enabled
[ 1.724673] printk: legacy bootconsole [early0] disabled
[ 1.751124] spi-mt7621 1e000b00.spi: sys_freq: 220000000
[ 1.763798] 4 fixed-partitions partitions found on MTD device spi0.0
[ 1.777037] Creating 4 MTD partitions on "spi0.0":
[ 1.786764] 0x000000000000-0x000000030000 : "u-boot"
[ 1.798583] 0x000000030000-0x000000040000 : "u-boot-env"
[ 1.810182] 0x000000f30000-0x000000f40000 : "factory"
[ 1.822199] 0x000000050000-0x000000f30000 : "firmware"
[ 1.833811] 2 uimage-fw partitions found on MTD device firmware
[ 1.845711] Creating 2 MTD partitions on "firmware":
[ 1.855621] 0x000000000000-0x000000330000 : "kernel"
[ 1.866641] 0x000000330000-0x000000ee0000 : "rootfs"
[ 1.877495] mtd: setting mtd5 (rootfs) as root device
[ 1.887804] 1 squashfs-split partitions found on MTD device rootfs
[ 1.900159] 0x000000850000-0x000000ee0000 : "rootfs_data"
[ 2.041149] mt7530-mdio mdio-bus:1f: MT7530 adapts as multi-chip module
[ 2.065479] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 15
[ 2.085238] mtk_soc_eth 1e100000.ethernet eth1: mediatek frame engine at 0xbe100000, irq 15
[ 2.103859] i2c_dev: i2c /dev entries driver
[ 2.116759] NET: Registered PF_INET6 protocol family
[ 2.130434] Segment Routing with IPv6
[ 2.137931] In-situ OAM (IOAM) with IPv6
[ 2.145856] NET: Registered PF_PACKET protocol family
[ 2.156073] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 2.182765] 8021q: 802.1Q VLAN Support v1.8
[ 2.226507] mt7530-mdio mdio-bus:1f: MT7530 adapts as multi-chip module
[ 2.267132] mt7530-mdio mdio-bus:1f: configuring for fixed/rgmii link mode
[ 2.282434] mt7530-mdio mdio-bus:1f lan4 (uninitialized): PHY [mt7530-0:00] driver [MediaTek MT7530 PHY] (irq=17)
[ 2.303481] mt7530-mdio mdio-bus:1f: Link is Up - 1Gbps/Full - flow control rx/tx
[ 2.311232] mt7530-mdio mdio-bus:1f lan3 (uninitialized): PHY [mt7530-0:01] driver [MediaTek MT7530 PHY] (irq=18)
[ 2.342129] mt7530-mdio mdio-bus:1f lan2 (uninitialized): PHY [mt7530-0:02] driver [MediaTek MT7530 PHY] (irq=19)
[ 2.365592] mt7530-mdio mdio-bus:1f lan1 (uninitialized): PHY [mt7530-0:03] driver [MediaTek MT7530 PHY] (irq=20)
[ 2.388647] mtk_soc_eth 1e100000.ethernet eth0: entered promiscuous mode
[ 2.402186] DSA: tree 0 setup
[ 2.409222] clk: Disabling unused clocks
[ 2.427475] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[ 2.446057] Freeing unused kernel image (initmem) memory: 1244K
[ 2.457936] This architecture does not have kernel memory protection.
[ 2.470800] Run /sbin/init as init process
[ 2.478966] with arguments:
[ 2.478977] /sbin/init
[ 2.478986] with environment:
[ 2.478993] HOME=/
[ 2.479001] TERM=linux
[ 3.475182] init: Console is alive
[ 3.482459] init: - watchdog -
[ 6.086714] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 6.204699] usbcore: registered new interface driver usbfs
[ 6.215945] usbcore: registered new interface driver hub
[ 6.226720] usbcore: registered new device driver usb
[ 6.317524] gpio_button_hotplug: loading out-of-tree module taints kernel.
[ 6.343989] SCSI subsystem initialized
[ 6.365476] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
[ 6.376216] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 1
[ 6.396234] xhci-mtk 1e1c0000.xhci: hcc params 0x01401198 hci version 0x96 quirks 0x0000000000280010
[ 6.414622] xhci-mtk 1e1c0000.xhci: irq 24, io mem 0x1e1c0000
[ 6.426418] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
[ 6.437047] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 2
[ 6.451977] xhci-mtk 1e1c0000.xhci: Host supports USB 3.0 SuperSpeed
[ 6.465771] hub 1-0:1.0: USB hub found
[ 6.473470] hub 1-0:1.0: 2 ports detected
[ 6.482626] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 6.499901] hub 2-0:1.0: USB hub found
[ 6.507491] hub 2-0:1.0: 1 port detected
[ 6.544908] usbcore: registered new interface driver usb-storage
[ 6.579298] usbcore: registered new interface driver uas
[ 6.590949] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 6.616729] init: - preinit -
[ 8.152798] mtk_soc_eth 1e100000.ethernet wan: renamed from eth1
[ 9.557736] random: crng init done
[ 10.094560] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
[ 10.115681] mt7530-mdio mdio-bus:1f lan1: configuring for phy/gmii link mode
[ 10.129914] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 14.579257] mount_root: loading kmods from internal overlay
[ 14.612637] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[ 14.629918] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[ 16.023981] block: attempting to load /tmp/overlay/upper/etc/config/fstab
[ 16.040860] block: unable to load configuration (fstab: Entry not found)
[ 16.054499] block: attempting to load /tmp/overlay/etc/config/fstab
[ 16.067263] block: unable to load configuration (fstab: Entry not found)
[ 16.080861] block: attempting to load /etc/config/fstab
[ 16.091607] block: unable to load configuration (fstab: Entry not found)
[ 16.105136] block: no usable configuration
[ 16.113976] block: attempting to load /etc/config/fstab
[ 16.124712] block: unable to load configuration (fstab: Entry not found)
[ 16.138231] block: no usable configuration
[ 16.147519] mount_root: jffs2 not ready yet, using temporary tmpfs overlay
[ 16.174172] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 16.860499] procd: - early -
[ 16.866466] procd: - watchdog -
[ 17.485669] procd: - watchdog -
[ 17.498597] procd: - ubus -
[ 17.716669] procd: - init -
[ 19.728733] kmodloader: loading kernel modules from /etc/modules.d/*
[ 19.875538] mtk-eip93 1e004000.crypto: EIP93 Crypto Engine Initialized.
[ 20.839524] urngd: v1.0.2 started.
[ 20.868227] ntfs3: Enabled Linux POSIX ACLs support
[ 20.913463] Loading modules backported from Linux version v6.18.39-0-gf89c29685
[ 20.928146] Backport generated by backports.git 614e5ed
[ 21.527263] pci 0000:00:02.0: enabling device (0000 -> 0003)
[ 21.538701] mt7603e 0000:01:00.0: enabling device (0000 -> 0002)
[ 21.550985] mt7603e 0000:01:00.0: ASIC revision: 76030010
[ 21.630229] mt7603e 0000:01:00.0: Firmware Version: ap_pcie
[ 21.641440] mt7603e 0000:01:00.0: Build Time: 20160107100755
[ 21.717696] mt7603e 0000:01:00.0: firmware init done
[ 21.904789] mt7603e 0000:01:00.0: registering led 'mt76-phy0'
[ 22.019070] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 22.227302] PPP generic driver version 2.4.2
[ 22.259288] NET: Registered PF_PPPOX protocol family
[ 22.298343] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 54.861906] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[ 54.877464] jffs2_build_filesystem(): unlocking the mtd device...
[ 54.877581] done.
[ 54.894008] jffs2_build_filesystem(): erasing all blocks after the end marker...
[ 59.507081] mtk_soc_eth 1e100000.ethernet eth0: Link is Down
[ 59.586659] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
[ 59.602798] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 59.627221] mt7530-mdio mdio-bus:1f lan1: configuring for phy/gmii link mode
[ 59.644429] br-lan: port 1(lan1) entered blocking state
[ 59.654975] br-lan: port 1(lan1) entered disabled state
[ 59.665555] mt7530-mdio mdio-bus:1f lan1: entered allmulticast mode
[ 59.678125] mtk_soc_eth 1e100000.ethernet eth0: entered allmulticast mode
[ 59.696113] mt7530-mdio mdio-bus:1f lan1: entered promiscuous mode
[ 59.768393] mt7530-mdio mdio-bus:1f lan2: configuring for phy/gmii link mode
[ 59.802324] br-lan: port 2(lan2) entered blocking state
[ 59.812875] br-lan: port 2(lan2) entered disabled state
[ 59.823531] mt7530-mdio mdio-bus:1f lan2: entered allmulticast mode
[ 59.839954] mt7530-mdio mdio-bus:1f lan2: entered promiscuous mode
[ 59.875641] mt7530-mdio mdio-bus:1f lan3: configuring for phy/gmii link mode
[ 59.909679] br-lan: port 3(lan3) entered blocking state
[ 59.920229] br-lan: port 3(lan3) entered disabled state
[ 59.930808] mt7530-mdio mdio-bus:1f lan3: entered allmulticast mode
[ 59.960297] mt7530-mdio mdio-bus:1f lan3: entered promiscuous mode
[ 60.020383] mt7530-mdio mdio-bus:1f lan4: configuring for phy/gmii link mode
[ 60.060007] br-lan: port 4(lan4) entered blocking state
[ 60.070678] br-lan: port 4(lan4) entered disabled state
[ 60.081399] mt7530-mdio mdio-bus:1f lan4: entered allmulticast mode
[ 60.129620] mt7530-mdio mdio-bus:1f lan4: entered promiscuous mode
[ 60.207303] mtk_soc_eth 1e100000.ethernet wan: PHY [mt7530-0:04] driver [MediaTek MT7530 PHY] (irq=POLL)
[ 60.226395] mtk_soc_eth 1e100000.ethernet wan: configuring for phy/rgmii link mode
[ 85.370065] done.
[ 85.373953] jffs2: notice: (1939) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 85.554796] overlayfs: upper fs does not support tmpfile.
[ 97.740002] mt7530-mdio mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control rx/tx
[ 97.740121] br-lan: port 1(lan1) entered blocking state
[ 97.766281] br-lan: port 1(lan1) entered forwarding state
[ 99.106012] mt7530-mdio mdio-bus:1f lan1: Link is Down
[ 99.128345] br-lan: port 1(lan1) entered disabled state
[ 101.732377] mt7530-mdio mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control rx/tx
[ 101.732476] br-lan: port 1(lan1) entered blocking state
[ 101.758672] br-lan: port 1(lan1) entered forwarding state
[ 103.098736] mt7530-mdio mdio-bus:1f lan1: Link is Down
[ 103.109239] br-lan: port 1(lan1) entered disabled state
[ 105.756830] mt7530-mdio mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control rx/tx
[ 105.772838] br-lan: port 1(lan1) entered blocking state
[ 105.783279] br-lan: port 1(lan1) entered forwarding state
[ 107.125588] mt7530-mdio mdio-bus:1f lan1: Link is Down
[ 107.136066] br-lan: port 1(lan1) entered disabled state
[ 109.214295] mt7530-mdio mdio-bus:1f lan1: Link is Up - 100Mbps/Full - flow control rx/tx
[ 109.214537] br-lan: port 1(lan1) entered blocking state
[ 109.240958] br-lan: port 1(lan1) entered forwarding state
root@OpenWrt:~# cat /etc/config/wireless
config wifi-device 'radio0'
option type 'mac80211'
option path '1e140000.pcie/pci0000:00/0000:00:02.0/0000:01:00.0'
option band '2g'
option channel '1'
option htmode 'HT20'
option country 'PL'
config wifi-iface 'default_radio0'
option device 'radio0'
option network 'lan'
option mode 'ap'
option ssid 'OpenWrt'
option encryption 'none'
option disabled '1'
ls -l /sys/bus/pci/devices/
lrwxrwxrwx 1 root root 0 Jan 1 1970 0000:00:02.0 -> ../../../devices/platform/1e140000.pcie/pci0000:00/0000:00:02.0
lrwxrwxrwx 1 root root 0 Jan 1 1970 0000:01:00.0 -> ../../../devices/platform/1e140000.pcie/pci0000:00/0000:00:02.0/0000:01:00.0
pcie0 no card
pcie1 no card
PCIE2 enabled
w sumie to ta sama bajka co na początku wątku ;D z tego co widze ucielo mi 65kb z 1MB factory
dd if=factory.bin of=flash.bin bs=64K seek=243 count=10 conv=notrunc
skrypt na wiki tnie, za bardzo, w ogóle partycja factory jest za mała
mwan3 tylko czasami nie działa jak należy, potrafi się nie przełączyć przy braku połączenia jeżeli fizycznie nie odepniemy przewodu ...
