Odp: Xiaomi AX3600
@smereka chcesz odpalić 160MHz na kanałach 100-128 czy 149-177?
Strony Poprzednia 1 … 13 14 15 16 17 … 48 Następna
Zaloguj się lub zarejestruj by napisać odpowiedź
Nie jesteś zalogowany. Proszę się zalogować lub zarejestrować.
Xiaomi AX3600 (Strona 15 z 48)
eko.one.pl → Sprzęt / Hardware → Xiaomi AX3600
Posty: 351 do 375 z 1,198
352 2023-01-26 12:15:33 (edytowany przez smereka 2023-01-26 12:16:35)
Odp: Xiaomi AX3600
Cezary napisał/a:
Wyłącz DFS. A jeżeli nie możesz to ustaw country code gdzie nie ma DFS (indonezja chyba). Tylko do testów, bo u nas powinieneś mieć włączone DFS.
A da się na testy to DFS wyłączyć w openwrt?
frutis napisał/a:
@smereka chcesz odpalić 160MHz na kanałach 100-128 czy 149-177?
Obojętnie jeśli się da bo nie wiem tego czy 160MHz jest obsługiwane na wszystkich kanałach dlatego właśnie pytam Was, może ktoś wnikał w to i wie
Odp: Xiaomi AX3600
Tu masz listę na jakich kanałach możesz złożyć 160MHz: https://en.wikipedia.org/wiki/List_of_W … j/n/ac/ax)
Teraz po pierwsze zrób iw list i zobaczysz jakimi kanałami w ogóle dysponuje to xiaomi i czy mówi że możesz złożyć 160MHz. I w końcu ustaw to countrycode na inne żeby nie widziało DFS. DFS jest domyślnie włączone w sterownikach qualcomma w openwrt.
Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.
Odp: Xiaomi AX3600
Dzięki wieczorem sprawdzę. Nie zrobiłem sobie wejścia z wanu do tego xiaomi wiec teraz nie mam jak sprawdzić. Dam znać. Ciekawa tabelka - zrobiło mi się jaśniej 
355 2023-01-26 13:20:15 (edytowany przez frutis 2023-01-26 13:49:27)
Odp: Xiaomi AX3600
Po ustawieniu US wstaje radio na 160MHz na kanałach 100-128.
A to wypluwa iw:
Wiphy phy1
wiphy index: 1
max # scan SSIDs: 16
max scan IEs length: 142 bytes
max # sched scan SSIDs: 0
max # match sets: 0
Retry short limit: 7
Retry long limit: 4
Coverage class: 0 (up to 0m)
Device supports AP-side u-APSD.
Available Antennas: TX 0xf0 RX 0xf0
Configured Antennas: TX 0xf0 RX 0xf0
Supported interface modes:
* managed
* AP
* monitor
* mesh point
Band 2:
Capabilities: 0x19e7
RX LDPC
HT20/HT40
Dynamic SM Power Save
RX HT20 SGI
RX HT40 SGI
TX STBC
RX STBC 1-stream
Max AMSDU length: 7935 bytes
DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: No restriction (0x00)
HT TX/RX MCS rate indexes supported: 0-31
VHT Capabilities (0x739b79fa):
Max MPDU length: 11454
Supported Channel Width: (reserved)
RX LDPC
short GI (80 MHz)
short GI (160/80+80 MHz)
TX STBC
SU Beamformer
SU Beamformee
MU Beamformer
MU Beamformee
RX antenna pattern consistency
TX antenna pattern consistency
VHT RX MCS set:
1 streams: MCS 0-9
2 streams: MCS 0-9
3 streams: MCS 0-9
4 streams: MCS 0-9
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
VHT RX highest supported: 0 Mbps
VHT TX MCS set:
1 streams: MCS 0-9
2 streams: MCS 0-9
3 streams: MCS 0-9
4 streams: MCS 0-9
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
VHT TX highest supported: 0 Mbps
VHT extended NSS: supported
HE Iftypes: managed
HE MAC Capabilities (0x000b9a181040):
+HTC HE Supported
TWT Requester
Dynamic BA Fragementation Level: 1
BSR
Broadcast TWT
OM Control
Maximum A-MPDU Length Exponent: 3
RX Control Frame to MultiBSS
A-MSDU in A-MPDU
OM Control UL MU Data Disable RX
HE PHY Capabilities: (0x1c604c897fdb839c010c00):
HE40/HE80/5GHz
HE160/5GHz
HE160/HE80+80/5GHz
LDPC Coding in Payload
HE SU PPDU with 1x HE-LTF and 0.8us GI
STBC Tx <= 80MHz
STBC Rx <= 80MHz
Full Bandwidth UL MU-MIMO
DCM Max Constellation: 1
DCM Max Constellation Rx: 1
SU Beamformer
SU Beamformee
MU Beamformer
Beamformee STS <= 80Mhz: 7
Beamformee STS > 80Mhz: 3
Sounding Dimensions <= 80Mhz: 3
Sounding Dimensions > 80Mhz: 3
Ng = 16 SU Feedback
Ng = 16 MU Feedback
Codebook Size SU Feedback
Codebook Size MU Feedback
PPE Threshold Present
HE SU PPDU & HE PPDU 4x HE-LTF 0.8us GI
Max NC: 3
STBC Rx > 80MHz
HE ER SU PPDU 4x HE-LTF 0.8us GI
TX 1024-QAM
RX 1024-QAM
HE RX MCS and NSS set <= 80 MHz
1 streams: MCS 0-11
2 streams: MCS 0-11
3 streams: MCS 0-11
4 streams: MCS 0-11
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
HE TX MCS and NSS set <= 80 MHz
1 streams: MCS 0-11
2 streams: MCS 0-11
3 streams: MCS 0-11
4 streams: MCS 0-11
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
HE RX MCS and NSS set 160 MHz
1 streams: MCS 0-11
2 streams: MCS 0-11
3 streams: not supported
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
HE TX MCS and NSS set 160 MHz
1 streams: MCS 0-11
2 streams: MCS 0-11
3 streams: not supported
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
EHT Iftypes: managed
EHT MAC Capabilities (0x0000):
EHT PHY Capabilities: (0x0000000000000000):
EHT MCS/NSS: (0x):
EHT bw <= 80 MHz, max NSS for MCS 8-9: Rx=0, Tx=0
EHT bw <= 80 MHz, max NSS for MCS 10-11: Rx=0, Tx=0
EHT bw <= 80 MHz, max NSS for MCS 12-13: Rx=0, Tx=0
EHT bw=160 MHz, max NSS for MCS 8-9: Rx=0, Tx=0
EHT bw=160 MHz, max NSS for MCS 10-11: Rx=0, Tx=0
EHT bw=160 MHz, max NSS for MCS 12-13: Rx=0, Tx=0
HE Iftypes: AP
HE MAC Capabilities (0x000d9a181040):
+HTC HE Supported
TWT Responder
Dynamic BA Fragementation Level: 1
BSR
Broadcast TWT
OM Control
Maximum A-MPDU Length Exponent: 3
RX Control Frame to MultiBSS
A-MSDU in A-MPDU
OM Control UL MU Data Disable RX
HE PHY Capabilities: (0x1c604c887fdb839c010c00):
HE40/HE80/5GHz
HE160/5GHz
HE160/HE80+80/5GHz
LDPC Coding in Payload
HE SU PPDU with 1x HE-LTF and 0.8us GI
STBC Tx <= 80MHz
STBC Rx <= 80MHz
Full Bandwidth UL MU-MIMO
DCM Max Constellation Rx: 1
SU Beamformer
SU Beamformee
MU Beamformer
Beamformee STS <= 80Mhz: 7
Beamformee STS > 80Mhz: 3
Sounding Dimensions <= 80Mhz: 3
Sounding Dimensions > 80Mhz: 3
Ng = 16 SU Feedback
Ng = 16 MU Feedback
Codebook Size SU Feedback
Codebook Size MU Feedback
PPE Threshold Present
HE SU PPDU & HE PPDU 4x HE-LTF 0.8us GI
Max NC: 3
STBC Rx > 80MHz
HE ER SU PPDU 4x HE-LTF 0.8us GI
TX 1024-QAM
RX 1024-QAM
HE RX MCS and NSS set <= 80 MHz
1 streams: MCS 0-11
2 streams: MCS 0-11
3 streams: MCS 0-11
4 streams: MCS 0-11
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
HE TX MCS and NSS set <= 80 MHz
1 streams: MCS 0-11
2 streams: MCS 0-11
3 streams: MCS 0-11
4 streams: MCS 0-11
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
HE RX MCS and NSS set 160 MHz
1 streams: MCS 0-11
2 streams: MCS 0-11
3 streams: not supported
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
HE TX MCS and NSS set 160 MHz
1 streams: MCS 0-11
2 streams: MCS 0-11
3 streams: not supported
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
EHT Iftypes: AP
EHT MAC Capabilities (0x0000):
EHT PHY Capabilities: (0x0000000000000000):
EHT MCS/NSS: (0x):
EHT bw <= 80 MHz, max NSS for MCS 8-9: Rx=0, Tx=0
EHT bw <= 80 MHz, max NSS for MCS 10-11: Rx=0, Tx=0
EHT bw <= 80 MHz, max NSS for MCS 12-13: Rx=0, Tx=0
EHT bw=160 MHz, max NSS for MCS 8-9: Rx=0, Tx=0
EHT bw=160 MHz, max NSS for MCS 10-11: Rx=0, Tx=0
EHT bw=160 MHz, max NSS for MCS 12-13: Rx=0, Tx=0
HE Iftypes: mesh point
HE MAC Capabilities (0x00098a081040):
+HTC HE Supported
Dynamic BA Fragementation Level: 1
BSR
OM Control
Maximum A-MPDU Length Exponent: 1
RX Control Frame to MultiBSS
A-MSDU in A-MPDU
OM Control UL MU Data Disable RX
HE PHY Capabilities: (0x1c600c807d5b811c000000):
HE40/HE80/5GHz
HE160/5GHz
HE160/HE80+80/5GHz
LDPC Coding in Payload
HE SU PPDU with 1x HE-LTF and 0.8us GI
STBC Tx <= 80MHz
STBC Rx <= 80MHz
SU Beamformer
SU Beamformee
Beamformee STS <= 80Mhz: 7
Beamformee STS > 80Mhz: 3
Sounding Dimensions <= 80Mhz: 3
Sounding Dimensions > 80Mhz: 3
Ng = 16 SU Feedback
Codebook Size SU Feedback
PPE Threshold Present
HE SU PPDU & HE PPDU 4x HE-LTF 0.8us GI
Max NC: 3
HE RX MCS and NSS set <= 80 MHz
1 streams: MCS 0-11
2 streams: MCS 0-11
3 streams: MCS 0-11
4 streams: MCS 0-11
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
HE TX MCS and NSS set <= 80 MHz
1 streams: MCS 0-11
2 streams: MCS 0-11
3 streams: MCS 0-11
4 streams: MCS 0-11
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
HE RX MCS and NSS set 160 MHz
1 streams: MCS 0-11
2 streams: MCS 0-11
3 streams: not supported
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
HE TX MCS and NSS set 160 MHz
1 streams: MCS 0-11
2 streams: MCS 0-11
3 streams: not supported
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
EHT Iftypes: mesh point
EHT MAC Capabilities (0x0000):
EHT PHY Capabilities: (0x0000000000000000):
EHT MCS/NSS: (0x):
EHT bw <= 80 MHz, max NSS for MCS 8-9: Rx=0, Tx=0
EHT bw <= 80 MHz, max NSS for MCS 10-11: Rx=0, Tx=0
EHT bw <= 80 MHz, max NSS for MCS 12-13: Rx=0, Tx=0
EHT bw=160 MHz, max NSS for MCS 8-9: Rx=0, Tx=0
EHT bw=160 MHz, max NSS for MCS 10-11: Rx=0, Tx=0
EHT bw=160 MHz, max NSS for MCS 12-13: Rx=0, Tx=0
Frequencies:
* 5180 MHz [36] (30.0 dBm)
* 5200 MHz [40] (30.0 dBm)
* 5220 MHz [44] (30.0 dBm)
* 5240 MHz [48] (30.0 dBm)
* 5260 MHz [52] (24.0 dBm) (radar detection)
* 5280 MHz [56] (24.0 dBm) (radar detection)
* 5300 MHz [60] (24.0 dBm) (radar detection)
* 5320 MHz [64] (24.0 dBm) (radar detection)
* 5500 MHz [100] (24.0 dBm) (radar detection)
* 5520 MHz [104] (24.0 dBm) (radar detection)
* 5540 MHz [108] (24.0 dBm) (radar detection)
* 5560 MHz [112] (24.0 dBm) (radar detection)
* 5580 MHz [116] (24.0 dBm) (radar detection)
* 5600 MHz [120] (24.0 dBm) (radar detection)
* 5620 MHz [124] (24.0 dBm) (radar detection)
* 5640 MHz [128] (24.0 dBm) (radar detection)
* 5660 MHz [132] (24.0 dBm) (radar detection)
* 5680 MHz [136] (24.0 dBm) (radar detection)
* 5700 MHz [140] (24.0 dBm) (radar detection)
* 5720 MHz [144] (24.0 dBm) (radar detection)
* 5745 MHz [149] (30.0 dBm)
* 5765 MHz [153] (30.0 dBm)
* 5785 MHz [157] (30.0 dBm)
* 5805 MHz [161] (30.0 dBm)
* 5825 MHz [165] (30.0 dBm)
* 5845 MHz [169] (disabled)
* 5865 MHz [173] (disabled)
valid interface combinations:
* #{ managed } <= 1, #{ AP, mesh point } <= 16,
total <= 16, #channels <= 1, STA/AP BI must match, radar detect widths: { 20 MHz (no HT), 20 MHz, 40 MHz, 80 MHz, 80+80 MHz, 160 MHz }
HT Capability overrides:
* MCS: ff ff ff ff ff ff ff ff ff ff
* maximum A-MSDU length
* supported channel width
* short GI for 40 MHz
* max A-MPDU length exponent
* min MPDU start spacing
max # scan plans: 1
max scan plan interval: -1
max scan plan iterations: 0
Maximum associated stations in AP mode: 128
Supported extended features:
* [ RRM ]: RRM
* [ SET_SCAN_DWELL ]: scan dwell setting
* [ FILS_STA ]: STA FILS (Fast Initial Link Setup)
* [ CQM_RSSI_LIST ]: multiple CQM_RSSI_THOLD records
* [ CONTROL_PORT_OVER_NL80211 ]: control port over nl80211
* [ TXQS ]: FQ-CoDel-enabled intermediate TXQs
* [ STA_TX_PWR ]: TX power control per station
* [ CONTROL_PORT_NO_PREAUTH ]: disable pre-auth over nl80211 control port support
* [ SCAN_FREQ_KHZ ]: scan on kHz frequency support
* [ CONTROL_PORT_OVER_NL80211_TX_STATUS ]: tx status for nl80211 control port support
* [ BSS_COLOR ]: BSS coloring supporta po ustawieniu PL radio nie wstaje, w logach nic nie ma a iw wypluwa:
Wiphy phy1
wiphy index: 1
max # scan SSIDs: 16
max scan IEs length: 142 bytes
max # sched scan SSIDs: 0
max # match sets: 0
Retry short limit: 7
Retry long limit: 4
Coverage class: 0 (up to 0m)
Device supports AP-side u-APSD.
Available Antennas: TX 0xf0 RX 0xf0
Configured Antennas: TX 0xf0 RX 0xf0
Supported interface modes:
* managed
* AP
* monitor
* mesh point
Band 2:
Capabilities: 0x19e7
RX LDPC
HT20/HT40
Dynamic SM Power Save
RX HT20 SGI
RX HT40 SGI
TX STBC
RX STBC 1-stream
Max AMSDU length: 7935 bytes
DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: No restriction (0x00)
HT TX/RX MCS rate indexes supported: 0-31
VHT Capabilities (0x739b79fa):
Max MPDU length: 11454
Supported Channel Width: (reserved)
RX LDPC
short GI (80 MHz)
short GI (160/80+80 MHz)
TX STBC
SU Beamformer
SU Beamformee
MU Beamformer
MU Beamformee
RX antenna pattern consistency
TX antenna pattern consistency
VHT RX MCS set:
1 streams: MCS 0-9
2 streams: MCS 0-9
3 streams: MCS 0-9
4 streams: MCS 0-9
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
VHT RX highest supported: 0 Mbps
VHT TX MCS set:
1 streams: MCS 0-9
2 streams: MCS 0-9
3 streams: MCS 0-9
4 streams: MCS 0-9
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
VHT TX highest supported: 0 Mbps
VHT extended NSS: supported
HE Iftypes: managed
HE MAC Capabilities (0x000b9a181040):
+HTC HE Supported
TWT Requester
Dynamic BA Fragementation Level: 1
BSR
Broadcast TWT
OM Control
Maximum A-MPDU Length Exponent: 3
RX Control Frame to MultiBSS
A-MSDU in A-MPDU
OM Control UL MU Data Disable RX
HE PHY Capabilities: (0x1c604c897fdb839c010c00):
HE40/HE80/5GHz
HE160/5GHz
HE160/HE80+80/5GHz
LDPC Coding in Payload
HE SU PPDU with 1x HE-LTF and 0.8us GI
STBC Tx <= 80MHz
STBC Rx <= 80MHz
Full Bandwidth UL MU-MIMO
DCM Max Constellation: 1
DCM Max Constellation Rx: 1
SU Beamformer
SU Beamformee
MU Beamformer
Beamformee STS <= 80Mhz: 7
Beamformee STS > 80Mhz: 3
Sounding Dimensions <= 80Mhz: 3
Sounding Dimensions > 80Mhz: 3
Ng = 16 SU Feedback
Ng = 16 MU Feedback
Codebook Size SU Feedback
Codebook Size MU Feedback
PPE Threshold Present
HE SU PPDU & HE PPDU 4x HE-LTF 0.8us GI
Max NC: 3
STBC Rx > 80MHz
HE ER SU PPDU 4x HE-LTF 0.8us GI
TX 1024-QAM
RX 1024-QAM
HE RX MCS and NSS set <= 80 MHz
1 streams: MCS 0-11
2 streams: MCS 0-11
3 streams: MCS 0-11
4 streams: MCS 0-11
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
HE TX MCS and NSS set <= 80 MHz
1 streams: MCS 0-11
2 streams: MCS 0-11
3 streams: MCS 0-11
4 streams: MCS 0-11
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
HE RX MCS and NSS set 160 MHz
1 streams: MCS 0-11
2 streams: MCS 0-11
3 streams: not supported
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
HE TX MCS and NSS set 160 MHz
1 streams: MCS 0-11
2 streams: MCS 0-11
3 streams: not supported
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
EHT Iftypes: managed
EHT MAC Capabilities (0x0000):
EHT PHY Capabilities: (0x0000000000000000):
EHT MCS/NSS: (0x):
EHT bw <= 80 MHz, max NSS for MCS 8-9: Rx=0, Tx=0
EHT bw <= 80 MHz, max NSS for MCS 10-11: Rx=0, Tx=0
EHT bw <= 80 MHz, max NSS for MCS 12-13: Rx=0, Tx=0
EHT bw=160 MHz, max NSS for MCS 8-9: Rx=0, Tx=0
EHT bw=160 MHz, max NSS for MCS 10-11: Rx=0, Tx=0
EHT bw=160 MHz, max NSS for MCS 12-13: Rx=0, Tx=0
HE Iftypes: AP
HE MAC Capabilities (0x000d9a181040):
+HTC HE Supported
TWT Responder
Dynamic BA Fragementation Level: 1
BSR
Broadcast TWT
OM Control
Maximum A-MPDU Length Exponent: 3
RX Control Frame to MultiBSS
A-MSDU in A-MPDU
OM Control UL MU Data Disable RX
HE PHY Capabilities: (0x1c604c887fdb839c010c00):
HE40/HE80/5GHz
HE160/5GHz
HE160/HE80+80/5GHz
LDPC Coding in Payload
HE SU PPDU with 1x HE-LTF and 0.8us GI
STBC Tx <= 80MHz
STBC Rx <= 80MHz
Full Bandwidth UL MU-MIMO
DCM Max Constellation Rx: 1
SU Beamformer
SU Beamformee
MU Beamformer
Beamformee STS <= 80Mhz: 7
Beamformee STS > 80Mhz: 3
Sounding Dimensions <= 80Mhz: 3
Sounding Dimensions > 80Mhz: 3
Ng = 16 SU Feedback
Ng = 16 MU Feedback
Codebook Size SU Feedback
Codebook Size MU Feedback
PPE Threshold Present
HE SU PPDU & HE PPDU 4x HE-LTF 0.8us GI
Max NC: 3
STBC Rx > 80MHz
HE ER SU PPDU 4x HE-LTF 0.8us GI
TX 1024-QAM
RX 1024-QAM
HE RX MCS and NSS set <= 80 MHz
1 streams: MCS 0-11
2 streams: MCS 0-11
3 streams: MCS 0-11
4 streams: MCS 0-11
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
HE TX MCS and NSS set <= 80 MHz
1 streams: MCS 0-11
2 streams: MCS 0-11
3 streams: MCS 0-11
4 streams: MCS 0-11
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
HE RX MCS and NSS set 160 MHz
1 streams: MCS 0-11
2 streams: MCS 0-11
3 streams: not supported
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
HE TX MCS and NSS set 160 MHz
1 streams: MCS 0-11
2 streams: MCS 0-11
3 streams: not supported
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
EHT Iftypes: AP
EHT MAC Capabilities (0x0000):
EHT PHY Capabilities: (0x0000000000000000):
EHT MCS/NSS: (0x):
EHT bw <= 80 MHz, max NSS for MCS 8-9: Rx=0, Tx=0
EHT bw <= 80 MHz, max NSS for MCS 10-11: Rx=0, Tx=0
EHT bw <= 80 MHz, max NSS for MCS 12-13: Rx=0, Tx=0
EHT bw=160 MHz, max NSS for MCS 8-9: Rx=0, Tx=0
EHT bw=160 MHz, max NSS for MCS 10-11: Rx=0, Tx=0
EHT bw=160 MHz, max NSS for MCS 12-13: Rx=0, Tx=0
HE Iftypes: mesh point
HE MAC Capabilities (0x00098a081040):
+HTC HE Supported
Dynamic BA Fragementation Level: 1
BSR
OM Control
Maximum A-MPDU Length Exponent: 1
RX Control Frame to MultiBSS
A-MSDU in A-MPDU
OM Control UL MU Data Disable RX
HE PHY Capabilities: (0x1c600c807d5b811c000000):
HE40/HE80/5GHz
HE160/5GHz
HE160/HE80+80/5GHz
LDPC Coding in Payload
HE SU PPDU with 1x HE-LTF and 0.8us GI
STBC Tx <= 80MHz
STBC Rx <= 80MHz
SU Beamformer
SU Beamformee
Beamformee STS <= 80Mhz: 7
Beamformee STS > 80Mhz: 3
Sounding Dimensions <= 80Mhz: 3
Sounding Dimensions > 80Mhz: 3
Ng = 16 SU Feedback
Codebook Size SU Feedback
PPE Threshold Present
HE SU PPDU & HE PPDU 4x HE-LTF 0.8us GI
Max NC: 3
HE RX MCS and NSS set <= 80 MHz
1 streams: MCS 0-11
2 streams: MCS 0-11
3 streams: MCS 0-11
4 streams: MCS 0-11
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
HE TX MCS and NSS set <= 80 MHz
1 streams: MCS 0-11
2 streams: MCS 0-11
3 streams: MCS 0-11
4 streams: MCS 0-11
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
HE RX MCS and NSS set 160 MHz
1 streams: MCS 0-11
2 streams: MCS 0-11
3 streams: not supported
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
HE TX MCS and NSS set 160 MHz
1 streams: MCS 0-11
2 streams: MCS 0-11
3 streams: not supported
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
EHT Iftypes: mesh point
EHT MAC Capabilities (0x0000):
EHT PHY Capabilities: (0x0000000000000000):
EHT MCS/NSS: (0x):
EHT bw <= 80 MHz, max NSS for MCS 8-9: Rx=0, Tx=0
EHT bw <= 80 MHz, max NSS for MCS 10-11: Rx=0, Tx=0
EHT bw <= 80 MHz, max NSS for MCS 12-13: Rx=0, Tx=0
EHT bw=160 MHz, max NSS for MCS 8-9: Rx=0, Tx=0
EHT bw=160 MHz, max NSS for MCS 10-11: Rx=0, Tx=0
EHT bw=160 MHz, max NSS for MCS 12-13: Rx=0, Tx=0
Frequencies:
* 5180 MHz [36] (30.0 dBm)
* 5200 MHz [40] (30.0 dBm)
* 5220 MHz [44] (30.0 dBm)
* 5240 MHz [48] (30.0 dBm)
* 5260 MHz [52] (24.0 dBm) (radar detection)
* 5280 MHz [56] (24.0 dBm) (radar detection)
* 5300 MHz [60] (24.0 dBm) (radar detection)
* 5320 MHz [64] (24.0 dBm) (radar detection)
* 5500 MHz [100] (24.0 dBm) (radar detection)
* 5520 MHz [104] (24.0 dBm) (radar detection)
* 5540 MHz [108] (24.0 dBm) (radar detection)
* 5560 MHz [112] (24.0 dBm) (radar detection)
* 5580 MHz [116] (24.0 dBm) (radar detection)
* 5600 MHz [120] (24.0 dBm) (radar detection)
* 5620 MHz [124] (24.0 dBm) (radar detection)
* 5640 MHz [128] (24.0 dBm) (radar detection)
* 5660 MHz [132] (24.0 dBm) (radar detection)
* 5680 MHz [136] (24.0 dBm) (radar detection)
* 5700 MHz [140] (24.0 dBm) (radar detection)
* 5720 MHz [144] (disabled)
* 5745 MHz [149] (disabled)
* 5765 MHz [153] (disabled)
* 5785 MHz [157] (disabled)
* 5805 MHz [161] (disabled)
* 5825 MHz [165] (disabled)
* 5845 MHz [169] (disabled)
* 5865 MHz [173] (disabled)
valid interface combinations:
* #{ managed } <= 1, #{ AP, mesh point } <= 16,
total <= 16, #channels <= 1, STA/AP BI must match, radar detect widths: { 20 MHz (no HT), 20 MHz, 40 MHz, 80 MHz, 80+80 MHz, 160 MHz }
HT Capability overrides:
* MCS: ff ff ff ff ff ff ff ff ff ff
* maximum A-MSDU length
* supported channel width
* short GI for 40 MHz
* max A-MPDU length exponent
* min MPDU start spacing
max # scan plans: 1
max scan plan interval: -1
max scan plan iterations: 0
Maximum associated stations in AP mode: 128
Supported extended features:
* [ RRM ]: RRM
* [ SET_SCAN_DWELL ]: scan dwell setting
* [ FILS_STA ]: STA FILS (Fast Initial Link Setup)
* [ CQM_RSSI_LIST ]: multiple CQM_RSSI_THOLD records
* [ CONTROL_PORT_OVER_NL80211 ]: control port over nl80211
* [ TXQS ]: FQ-CoDel-enabled intermediate TXQs
* [ STA_TX_PWR ]: TX power control per station
* [ CONTROL_PORT_NO_PREAUTH ]: disable pre-auth over nl80211 control port support
* [ SCAN_FREQ_KHZ ]: scan on kHz frequency support
* [ CONTROL_PORT_OVER_NL80211_TX_STATUS ]: tx status for nl80211 control port support
* [ BSS_COLOR ]: BSS coloring supportA tutaj jest baza jak by ktoś chciał sobie zerknąć co ma jaki kraj: https://git.kernel.org/pub/scm/linux/ke … ree/db.txt
EDIT:
Dla zakresu kanałów 100-128 w bazie jest:
- US: (5470 - 5730 @ 160), (24), DFS
- PL: (5470 - 5725 @ 160), (500 mW), DFS, wmmrule=ETSI
Czy to wmmrule=ETSI jest problemem?
356 2023-01-26 13:40:49 (edytowany przez pepe2k 2023-01-26 13:41:00)
- pepe2k
- Użytkownik
- Nieaktywny
Odp: Xiaomi AX3600
Dlaczego ucinasz co wypluwa iw? Pokaż całość... jest tam m.in. informacja o konfiguracji szerokości kanałów.
357 2023-01-26 13:49:43 (edytowany przez frutis 2023-01-26 13:58:21)
Odp: Xiaomi AX3600
pepe2k napisał/a:
Dlaczego ucinasz co wypluwa iw? Pokaż całość... jest tam m.in. informacja o konfiguracji szerokości kanałów.
Zedytowałem.
Dane są identyczne poza ustawieniami dla kanałów:
- PL
* 5720 MHz [144] (disabled)
* 5745 MHz [149] (disabled)
* 5765 MHz [153] (disabled)
* 5785 MHz [157] (disabled)
* 5805 MHz [161] (disabled)
* 5825 MHz [165] (disabled)- US
* 5720 MHz [144] (24.0 dBm) (radar detection)
* 5745 MHz [149] (30.0 dBm)
* 5765 MHz [153] (30.0 dBm)
* 5785 MHz [157] (30.0 dBm)
* 5805 MHz [161] (30.0 dBm)
* 5825 MHz [165] (30.0 dBm)Odp: Xiaomi AX3600
U mnie w logach na pewno są błędy. Wrócę do domu to wstawię i przeanalizujecie.
359 2023-01-26 14:50:03 (edytowany przez frutis 2023-01-26 15:02:20)
Odp: Xiaomi AX3600
Jednak działa na PL na kanałach 100-128 na 160MHz. Tylko trzeba sobie poczekać 10 minut zanim radio wstanie (cac_time=600s):
Wed Jan 25 23:35:47 2023 daemon.notice hostapd: Configuration file: /var/run/hostapd-phy1.conf (phy phy1-ap0) --> new PHY
Wed Jan 25 23:35:47 2023 kern.info kernel: [ 199.415895] br-lan: port 4(phy1-ap0) entered blocking state
Wed Jan 25 23:35:47 2023 kern.info kernel: [ 199.415944] br-lan: port 4(phy1-ap0) entered disabled state
Wed Jan 25 23:35:47 2023 kern.info kernel: [ 199.420527] device phy1-ap0 entered promiscuous mode
Wed Jan 25 23:35:47 2023 daemon.notice hostapd: phy1-ap0: interface state UNINITIALIZED->COUNTRY_UPDATE
Wed Jan 25 23:35:47 2023 daemon.notice hostapd: phy1-ap0: interface state COUNTRY_UPDATE->HT_SCAN
Wed Jan 25 23:35:48 2023 daemon.notice hostapd: phy1-ap0: interface state HT_SCAN->DFS
Wed Jan 25 23:35:48 2023 daemon.notice hostapd: phy1-ap0: DFS-CAC-START freq=5500 chan=100 sec_chan=1, width=2, seg0=114, seg1=0, cac_time=600s
Wed Jan 25 23:35:48 2023 daemon.notice netifd: Wireless device 'radio1' is now up
Wed Jan 25 23:46:20 2023 daemon.notice hostapd: phy1-ap0: DFS-CAC-COMPLETED success=1 freq=5500 ht_enabled=0 chan_offset=0 chan_width=5 cf1=5570 cf2=0
Wed Jan 25 23:46:20 2023 kern.info kernel: [ 832.647994] IPv6: ADDRCONF(NETDEV_CHANGE): phy1-ap0: link becomes ready
Wed Jan 25 23:46:20 2023 kern.info kernel: [ 832.648175] br-lan: port 4(phy1-ap0) entered blocking state
Wed Jan 25 23:46:20 2023 kern.info kernel: [ 832.653449] br-lan: port 4(phy1-ap0) entered forwarding state
Wed Jan 25 23:46:20 2023 daemon.notice netifd: Network device 'phy1-ap0' link is up
Wed Jan 25 23:46:21 2023 daemon.notice hostapd: phy1-ap0: interface state DFS->ENABLED
Wed Jan 25 23:46:21 2023 daemon.notice hostapd: phy1-ap0: AP-ENABLEDNa kanałach 36-64 skanowanie trwa tylko minutę (cac_time=60s):
Wed Jan 25 23:54:30 2023 daemon.notice hostapd: Configuration file: /var/run/hostapd-phy1.conf (phy phy1-ap0) --> new PHY
Wed Jan 25 23:54:30 2023 kern.info kernel: [ 1322.555210] br-lan: port 4(phy1-ap0) entered blocking state
Wed Jan 25 23:54:30 2023 kern.info kernel: [ 1322.555265] br-lan: port 4(phy1-ap0) entered disabled state
Wed Jan 25 23:54:30 2023 kern.info kernel: [ 1322.559806] device phy1-ap0 entered promiscuous mode
Wed Jan 25 23:54:30 2023 kern.info kernel: [ 1322.565323] br-lan: port 4(phy1-ap0) entered blocking state
Wed Jan 25 23:54:30 2023 daemon.notice hostapd: phy1-ap0: interface state UNINITIALIZED->COUNTRY_UPDATE
Wed Jan 25 23:54:30 2023 daemon.notice hostapd: phy1-ap0: interface state COUNTRY_UPDATE->HT_SCAN
Wed Jan 25 23:54:30 2023 kern.info kernel: [ 1322.570384] br-lan: port 4(phy1-ap0) entered forwarding state
Wed Jan 25 23:54:31 2023 daemon.notice hostapd: phy1-ap0: interface state HT_SCAN->DFS
Wed Jan 25 23:54:31 2023 daemon.notice hostapd: phy1-ap0: DFS-CAC-START freq=5180 chan=36 sec_chan=1, width=2, seg0=50, seg1=0, cac_time=60s
Wed Jan 25 23:54:31 2023 kern.info kernel: [ 1322.960601] br-lan: port 4(phy1-ap0) entered disabled state
Wed Jan 25 23:54:31 2023 daemon.notice netifd: Wireless device 'radio1' is now up
Wed Jan 25 23:55:33 2023 daemon.notice hostapd: phy1-ap0: DFS-CAC-COMPLETED success=1 freq=5180 ht_enabled=0 chan_offset=0 chan_width=5 cf1=5250 cf2=0
Wed Jan 25 23:55:33 2023 daemon.warn hostapd: Can't set DFS state for freq 5180 MHz
Wed Jan 25 23:55:33 2023 daemon.warn hostapd: Can't set DFS state for freq 5200 MHz
Wed Jan 25 23:55:33 2023 daemon.warn hostapd: Can't set DFS state for freq 5220 MHz
Wed Jan 25 23:55:33 2023 daemon.warn hostapd: Can't set DFS state for freq 5240 MHz
Wed Jan 25 23:55:34 2023 kern.info kernel: [ 1386.047699] IPv6: ADDRCONF(NETDEV_CHANGE): phy1-ap0: link becomes ready
Wed Jan 25 23:55:34 2023 kern.info kernel: [ 1386.047887] br-lan: port 4(phy1-ap0) entered blocking state
Wed Jan 25 23:55:34 2023 kern.info kernel: [ 1386.053159] br-lan: port 4(phy1-ap0) entered forwarding state
Wed Jan 25 23:55:34 2023 daemon.notice netifd: Network device 'phy1-ap0' link is up
Wed Jan 25 23:55:34 2023 daemon.notice hostapd: phy1-ap0: interface state DFS->ENABLED
Wed Jan 25 23:55:34 2023 daemon.notice hostapd: phy1-ap0: AP-ENABLED360 2023-01-26 20:44:08 (edytowany przez smereka 2023-01-26 20:45:45)
Odp: Xiaomi AX3600
No jakieś komedie się dzieją. Ustawiłem kanał 100 i działa, ustawiłem 149 i działa. Nie wiem co on odpiernicza ale zabanglał. Odsunąłem się maksymalnie od sąsiadów i puki co 0 zakłóceń. Ale żeby nie być gołosłownym logi a wczoraj. Nie resetowałem xiaomi więc można analizować;)
Wed Jan 25 21:49:33 2023 daemon.notice hostapd: phy1-ap0: interface state UNINITIALIZED->COUNTRY_UPDATE
Wed Jan 25 21:49:33 2023 daemon.err hostapd: Interface initialization failed
Wed Jan 25 21:49:33 2023 daemon.notice hostapd: phy1-ap0: interface state COUNTRY_UPDATE->DISABLED
Wed Jan 25 21:49:33 2023 daemon.notice hostapd: phy1-ap0: AP-DISABLED
Wed Jan 25 21:49:33 2023 daemon.err hostapd: phy1-ap0: Unable to setup interface.
Wed Jan 25 21:49:33 2023 daemon.notice hostapd: nl80211: deinit ifname=phy1-ap0 disabled_11b_rates=0
Wed Jan 25 21:49:33 2023 kern.info kernel: [ 4505.628207] device phy1-ap0 left promiscuous mode
Wed Jan 25 21:49:33 2023 kern.info kernel: [ 4505.632490] br-lan: port 5(phy1-ap0) entered disabled state
Wed Jan 25 21:49:34 2023 daemon.err hostapd: rmdir[ctrl_interface=/var/run/hostapd]: Permission denied
Wed Jan 25 21:49:34 2023 daemon.notice hostapd: phy1-ap0: CTRL-EVENT-TERMINATING
Wed Jan 25 21:49:34 2023 daemon.err hostapd: hostapd_free_hapd_data: Interface phy1-ap0 wasn't started
Wed Jan 25 21:49:34 2023 daemon.notice netifd: radio1 (18956): Command failed: ubus call hostapd config_add {"iface":"phy1-ap0", "config":"/var/run/hostapd-phy1.conf"} (Invalid argument)
Wed Jan 25 21:49:34 2023 daemon.notice netifd: radio1 (18956): Usage: ubus [<options>] <command> [arguments...]
Wed Jan 25 21:49:34 2023 daemon.notice netifd: radio1 (18956): Options:
Wed Jan 25 21:49:34 2023 daemon.notice netifd: radio1 (18956): -s <socket>: Set the unix domain socket to connect to
Wed Jan 25 21:49:34 2023 daemon.notice netifd: radio1 (18956): -t <timeout>: Set the timeout (in seconds) for a command to complete
Wed Jan 25 21:49:34 2023 daemon.notice netifd: radio1 (18956): -S: Use simplified output (for scripts)
Wed Jan 25 21:49:34 2023 daemon.notice netifd: radio1 (18956): -v: More verbose output
Wed Jan 25 21:49:34 2023 daemon.notice netifd: radio1 (18956): -m <type>: (for monitor): include a specific message type
Wed Jan 25 21:49:34 2023 daemon.notice netifd: radio1 (18956): (can be used more than once)
Wed Jan 25 21:49:34 2023 daemon.notice netifd: radio1 (18956): -M <r|t> (for monitor): only capture received or transmitted traffic
Wed Jan 25 21:49:34 2023 daemon.notice netifd: radio1 (18956):
Wed Jan 25 21:49:34 2023 daemon.notice netifd: radio1 (18956): Commands:
Wed Jan 25 21:49:34 2023 daemon.notice netifd: radio1 (18956): - list [<path>] List objects
Wed Jan 25 21:49:34 2023 daemon.notice netifd: radio1 (18956): - call <path> <method> [<message>] Call an object method
Wed Jan 25 21:49:34 2023 daemon.notice netifd: radio1 (18956): - subscribe <path> [<path>...] Subscribe to object(s) notifications
Wed Jan 25 21:49:34 2023 daemon.notice netifd: radio1 (18956): - listen [<path>...] Listen for events
Wed Jan 25 21:49:34 2023 daemon.notice netifd: radio1 (18956): - send <type> [<message>] Send an event
Wed Jan 25 21:49:34 2023 daemon.notice netifd: radio1 (18956): - wait_for <object> [<object>...] Wait for multiple objects to appear on ubus
Wed Jan 25 21:49:34 2023 daemon.notice netifd: radio1 (18956): - monitor Monitor ubus traffic
Wed Jan 25 21:49:34 2023 daemon.notice netifd: radio1 (18956):
Wed Jan 25 21:49:34 2023 daemon.notice netifd: radio1 (18956): Device setup failed: HOSTAPD_START_FAILED
Wed Jan 25 21:49:34 2023 daemon.notice netifd: Wireless device 'radio1' set retry=0
Wed Jan 25 21:49:34 2023 daemon.crit netifd: Wireless device 'radio1' setup failed, retry=0
Wed Jan 25 21:49:34 2023 daemon.notice netifd: Wireless device 'radio1' is now down
Wed Jan 25 21:49:35 2023 daemon.info dnsmasq[1]: read /etc/hosts - 12 names
Wed Jan 25 21:49:35 2023 daemon.info dnsmasq[1]: read /tmp/hosts/dhcp.cfg01411c - 4 names
Wed Jan 25 21:49:35 2023 daemon.info dnsmasq[1]: read /tmp/hosts/odhcpd - 4 names
Wed Jan 25 21:49:35 2023 daemon.info dnsmasq-dhcp[1]: read /etc/ethers - 0 addresses
Wed Jan 25 21:50:06 2023 daemon.notice hostapd: Configuration file: /var/run/hostapd-phy1.conf (phy phy1-ap0) --> new PHY
Wed Jan 25 21:50:06 2023 kern.info kernel: [ 4538.160739] br-lan: port 5(phy1-ap0) entered blocking state
Wed Jan 25 21:50:06 2023 kern.info kernel: [ 4538.160787] br-lan: port 5(phy1-ap0) entered disabled state
Wed Jan 25 21:50:06 2023 kern.info kernel: [ 4538.165419] device phy1-ap0 entered promiscuous mode
Wed Jan 25 21:50:06 2023 kern.info kernel: [ 4538.170807] br-lan: port 5(phy1-ap0) entered blocking state
Wed Jan 25 21:50:06 2023 kern.info kernel: [ 4538.175917] br-lan: port 5(phy1-ap0) entered forwarding state
Wed Jan 25 21:50:06 2023 daemon.notice hostapd: phy1-ap0: interface state UNINITIALIZED->COUNTRY_UPDATE
Wed Jan 25 21:50:06 2023 daemon.err hostapd: Interface initialization failed
Wed Jan 25 21:50:06 2023 daemon.notice hostapd: phy1-ap0: interface state COUNTRY_UPDATE->DISABLED
Wed Jan 25 21:50:06 2023 daemon.notice hostapd: phy1-ap0: AP-DISABLED
Wed Jan 25 21:50:06 2023 daemon.err hostapd: phy1-ap0: Unable to setup interface.
Wed Jan 25 21:50:06 2023 daemon.notice hostapd: nl80211: deinit ifname=phy1-ap0 disabled_11b_rates=0
Wed Jan 25 21:50:06 2023 kern.info kernel: [ 4538.181953] br-lan: port 5(phy1-ap0) entered disabled state
Wed Jan 25 21:50:06 2023 kern.info kernel: [ 4538.188289] device phy1-ap0 left promiscuous mode
Wed Jan 25 21:50:06 2023 kern.info kernel: [ 4538.192725] br-lan: port 5(phy1-ap0) entered disabled state
Wed Jan 25 21:50:06 2023 daemon.err hostapd: rmdir[ctrl_interface=/var/run/hostapd]: Permission denied
Wed Jan 25 21:50:06 2023 daemon.notice hostapd: phy1-ap0: CTRL-EVENT-TERMINATING
Wed Jan 25 21:50:06 2023 daemon.err hostapd: hostapd_free_hapd_data: Interface phy1-ap0 wasn't started
Wed Jan 25 21:50:06 2023 daemon.notice netifd: radio1 (19299): Command failed: ubus call hostapd config_add {"iface":"phy1-ap0", "config":"/var/run/hostapd-phy1.conf"} (Invalid argument)
Wed Jan 25 21:50:06 2023 daemon.notice netifd: radio1 (19299): Usage: ubus [<options>] <command> [arguments...]
Wed Jan 25 21:50:06 2023 daemon.notice netifd: radio1 (19299): Options:
Wed Jan 25 21:50:06 2023 daemon.notice netifd: radio1 (19299): -s <socket>: Set the unix domain socket to connect to
Wed Jan 25 21:50:06 2023 daemon.notice netifd: radio1 (19299): -t <timeout>: Set the timeout (in seconds) for a command to complete
Wed Jan 25 21:50:06 2023 daemon.notice netifd: radio1 (19299): -S: Use simplified output (for scripts)
Wed Jan 25 21:50:06 2023 daemon.notice netifd: radio1 (19299): -v: More verbose output
Wed Jan 25 21:50:06 2023 daemon.notice netifd: radio1 (19299): -m <type>: (for monitor): include a specific message type
Wed Jan 25 21:50:06 2023 daemon.notice netifd: radio1 (19299): (can be used more than once)
Wed Jan 25 21:50:06 2023 daemon.notice netifd: radio1 (19299): -M <r|t> (for monitor): only capture received or transmitted traffic
Wed Jan 25 21:50:06 2023 daemon.notice netifd: radio1 (19299):
Wed Jan 25 21:50:06 2023 daemon.notice netifd: radio1 (19299): Commands:
Wed Jan 25 21:50:06 2023 daemon.notice netifd: radio1 (19299): - list [<path>] List objects
Wed Jan 25 21:50:06 2023 daemon.notice netifd: radio1 (19299): - call <path> <method> [<message>] Call an object method
Wed Jan 25 21:50:06 2023 daemon.notice netifd: radio1 (19299): - subscribe <path> [<path>...] Subscribe to object(s) notifications
Wed Jan 25 21:50:06 2023 daemon.notice netifd: radio1 (19299): - listen [<path>...] Listen for events
Wed Jan 25 21:50:06 2023 daemon.notice netifd: radio1 (19299): - send <type> [<message>] Send an event
Wed Jan 25 21:50:06 2023 daemon.notice netifd: radio1 (19299): - wait_for <object> [<object>...] Wait for multiple objects to appear on ubus
Wed Jan 25 21:50:06 2023 daemon.notice netifd: radio1 (19299): - monitor Monitor ubus traffic
Wed Jan 25 21:50:06 2023 daemon.notice netifd: radio1 (19299):
Wed Jan 25 21:50:06 2023 daemon.notice netifd: radio1 (19299): Device setup failed: HOSTAPD_START_FAILED
Wed Jan 25 21:50:06 2023 daemon.notice netifd: Wireless device 'radio1' set retry=0
Wed Jan 25 21:50:06 2023 daemon.crit netifd: Wireless device 'radio1' setup failed, retry=0
Wed Jan 25 21:50:06 2023 daemon.notice netifd: Wireless device 'radio1' is now down
Wed Jan 25 21:50:08 2023 daemon.info dnsmasq[1]: read /etc/hosts - 12 names
Wed Jan 25 21:50:08 2023 daemon.info dnsmasq[1]: read /tmp/hosts/dhcp.cfg01411c - 4 names
Wed Jan 25 21:50:08 2023 daemon.info dnsmasq[1]: read /tmp/hosts/odhcpd - 4 names
Wed Jan 25 21:50:08 2023 daemon.info dnsmasq-dhcp[1]: read /etc/ethers - 0 addresses
Wed Jan 25 21:50:47 2023 daemon.notice hostapd: Configuration file: /var/run/hostapd-phy1.conf (phy phy1-ap0) --> new PHY
Wed Jan 25 21:50:47 2023 kern.info kernel: [ 4579.724417] br-lan: port 5(phy1-ap0) entered blocking state
Wed Jan 25 21:50:47 2023 kern.info kernel: [ 4579.724465] br-lan: port 5(phy1-ap0) entered disabled state
Wed Jan 25 21:50:47 2023 kern.info kernel: [ 4579.729030] device phy1-ap0 entered promiscuous mode
Wed Jan 25 21:50:47 2023 kern.info kernel: [ 4579.734541] br-lan: port 5(phy1-ap0) entered blocking state
Wed Jan 25 21:50:47 2023 kern.info kernel: [ 4579.739572] br-lan: port 5(phy1-ap0) entered forwarding state
Wed Jan 25 21:50:47 2023 daemon.notice hostapd: phy1-ap0: interface state UNINITIALIZED->COUNTRY_UPDATE
Wed Jan 25 21:50:47 2023 kern.info kernel: [ 4579.745379] br-lan: port 5(phy1-ap0) entered disabled state
Wed Jan 25 21:50:47 2023 daemon.err hostapd: Interface initialization failed
Wed Jan 25 21:50:47 2023 daemon.notice hostapd: phy1-ap0: interface state COUNTRY_UPDATE->DISABLED
Wed Jan 25 21:50:47 2023 daemon.notice hostapd: phy1-ap0: AP-DISABLED
Wed Jan 25 21:50:47 2023 daemon.err hostapd: phy1-ap0: Unable to setup interface.
Wed Jan 25 21:50:47 2023 daemon.notice hostapd: nl80211: deinit ifname=phy1-ap0 disabled_11b_rates=0
Wed Jan 25 21:50:47 2023 kern.info kernel: [ 4579.752092] device phy1-ap0 left promiscuous mode
Wed Jan 25 21:50:47 2023 kern.info kernel: [ 4579.756235] br-lan: port 5(phy1-ap0) entered disabled state
Wed Jan 25 21:50:48 2023 daemon.err hostapd: rmdir[ctrl_interface=/var/run/hostapd]: Permission denied
Wed Jan 25 21:50:48 2023 daemon.notice hostapd: phy1-ap0: CTRL-EVENT-TERMINATING
Wed Jan 25 21:50:48 2023 daemon.err hostapd: hostapd_free_hapd_data: Interface phy1-ap0 wasn't started
Wed Jan 25 21:50:48 2023 daemon.notice netifd: radio1 (19698): Command failed: ubus call hostapd config_add {"iface":"phy1-ap0", "config":"/var/run/hostapd-phy1.conf"} (Invalid argument)
Wed Jan 25 21:50:48 2023 daemon.notice netifd: radio1 (19698): Usage: ubus [<options>] <command> [arguments...]
Wed Jan 25 21:50:48 2023 daemon.notice netifd: radio1 (19698): Options:
Wed Jan 25 21:50:48 2023 daemon.notice netifd: radio1 (19698): -s <socket>: Set the unix domain socket to connect to
Wed Jan 25 21:50:48 2023 daemon.notice netifd: radio1 (19698): -t <timeout>: Set the timeout (in seconds) for a command to complete
Wed Jan 25 21:50:48 2023 daemon.notice netifd: radio1 (19698): -S: Use simplified output (for scripts)
Wed Jan 25 21:50:48 2023 daemon.notice netifd: radio1 (19698): -v: More verbose output
Wed Jan 25 21:50:48 2023 daemon.notice netifd: radio1 (19698): -m <type>: (for monitor): include a specific message type
Wed Jan 25 21:50:48 2023 daemon.notice netifd: radio1 (19698): (can be used more than once)
Wed Jan 25 21:50:48 2023 daemon.notice netifd: radio1 (19698): -M <r|t> (for monitor): only capture received or transmitted traffic
Wed Jan 25 21:50:48 2023 daemon.notice netifd: radio1 (19698):
Wed Jan 25 21:50:48 2023 daemon.notice netifd: radio1 (19698): Commands:
Wed Jan 25 21:50:48 2023 daemon.notice netifd: radio1 (19698): - list [<path>] List objects
Wed Jan 25 21:50:48 2023 daemon.notice netifd: radio1 (19698): - call <path> <method> [<message>] Call an object method
Wed Jan 25 21:50:48 2023 daemon.notice netifd: radio1 (19698): - subscribe <path> [<path>...] Subscribe to object(s) notifications
Wed Jan 25 21:50:48 2023 daemon.notice netifd: radio1 (19698): - listen [<path>...] Listen for events
Wed Jan 25 21:50:48 2023 daemon.notice netifd: radio1 (19698): - send <type> [<message>] Send an event
Wed Jan 25 21:50:48 2023 daemon.notice netifd: radio1 (19698): - wait_for <object> [<object>...] Wait for multiple objects to appear on ubus
Wed Jan 25 21:50:48 2023 daemon.notice netifd: radio1 (19698): - monitor Monitor ubus traffic
Wed Jan 25 21:50:48 2023 daemon.notice netifd: radio1 (19698):
Wed Jan 25 21:50:48 2023 daemon.notice netifd: radio1 (19698): Device setup failed: HOSTAPD_START_FAILED
Wed Jan 25 21:50:48 2023 daemon.notice netifd: Wireless device 'radio1' set retry=0
Wed Jan 25 21:50:48 2023 daemon.crit netifd: Wireless device 'radio1' setup failed, retry=0
Wed Jan 25 21:50:48 2023 daemon.notice netifd: Wireless device 'radio1' is now down
Wed Jan 25 21:50:49 2023 daemon.info dnsmasq[1]: read /etc/hosts - 12 names
Wed Jan 25 21:50:49 2023 daemon.info dnsmasq[1]: read /tmp/hosts/dhcp.cfg01411c - 4 names
Wed Jan 25 21:50:49 2023 daemon.info dnsmasq[1]: read /tmp/hosts/odhcpd - 4 names
Wed Jan 25 21:50:49 2023 daemon.info dnsmasq-dhcp[1]: read /etc/ethers - 0 addresses
Wed Jan 25 21:51:13 2023 daemon.notice hostapd: Configuration file: /var/run/hostapd-phy1.conf (phy phy1-ap0) --> new PHY
Wed Jan 25 21:51:13 2023 kern.info kernel: [ 4605.571702] br-lan: port 5(phy1-ap0) entered blocking state
Wed Jan 25 21:51:13 2023 kern.info kernel: [ 4605.571750] br-lan: port 5(phy1-ap0) entered disabled state
Wed Jan 25 21:51:13 2023 kern.info kernel: [ 4605.576308] device phy1-ap0 entered promiscuous mode
Wed Jan 25 21:51:13 2023 kern.info kernel: [ 4605.581815] br-lan: port 5(phy1-ap0) entered blocking state
Wed Jan 25 21:51:13 2023 kern.info kernel: [ 4605.586858] br-lan: port 5(phy1-ap0) entered forwarding state
Wed Jan 25 21:51:13 2023 daemon.notice hostapd: phy1-ap0: interface state UNINITIALIZED->COUNTRY_UPDATE
Wed Jan 25 21:51:13 2023 daemon.err hostapd: Interface initialization failed
Wed Jan 25 21:51:13 2023 daemon.notice hostapd: phy1-ap0: interface state COUNTRY_UPDATE->DISABLED
Wed Jan 25 21:51:13 2023 daemon.notice hostapd: phy1-ap0: AP-DISABLED
Wed Jan 25 21:51:13 2023 daemon.err hostapd: phy1-ap0: Unable to setup interface.
Wed Jan 25 21:51:13 2023 daemon.notice hostapd: nl80211: deinit ifname=phy1-ap0 disabled_11b_rates=0
Wed Jan 25 21:51:13 2023 kern.info kernel: [ 4605.592584] br-lan: port 5(phy1-ap0) entered disabled state
Wed Jan 25 21:51:13 2023 kern.info kernel: [ 4605.599312] device phy1-ap0 left promiscuous mode
Wed Jan 25 21:51:13 2023 kern.info kernel: [ 4605.603556] br-lan: port 5(phy1-ap0) entered disabled state
Wed Jan 25 21:51:13 2023 daemon.err hostapd: rmdir[ctrl_interface=/var/run/hostapd]: Permission denied
Wed Jan 25 21:51:13 2023 daemon.notice hostapd: phy1-ap0: CTRL-EVENT-TERMINATING
Wed Jan 25 21:51:13 2023 daemon.err hostapd: hostapd_free_hapd_data: Interface phy1-ap0 wasn't started
Wed Jan 25 21:51:13 2023 daemon.notice netifd: radio1 (20093): Command failed: ubus call hostapd config_add {"iface":"phy1-ap0", "config":"/var/run/hostapd-phy1.conf"} (Invalid argument)
Wed Jan 25 21:51:13 2023 daemon.notice netifd: radio1 (20093): Usage: ubus [<options>] <command> [arguments...]
Wed Jan 25 21:51:13 2023 daemon.notice netifd: radio1 (20093): Options:
Wed Jan 25 21:51:13 2023 daemon.notice netifd: radio1 (20093): -s <socket>: Set the unix domain socket to connect to
Wed Jan 25 21:51:13 2023 daemon.notice netifd: radio1 (20093): -t <timeout>: Set the timeout (in seconds) for a command to complete
Wed Jan 25 21:51:13 2023 daemon.notice netifd: radio1 (20093): -S: Use simplified output (for scripts)
Wed Jan 25 21:51:13 2023 daemon.notice netifd: radio1 (20093): -v: More verbose output
Wed Jan 25 21:51:13 2023 daemon.notice netifd: radio1 (20093): -m <type>: (for monitor): include a specific message type
Wed Jan 25 21:51:13 2023 daemon.notice netifd: radio1 (20093): (can be used more than once)
Wed Jan 25 21:51:13 2023 daemon.notice netifd: radio1 (20093): -M <r|t> (for monitor): only capture received or transmitted traffic
Wed Jan 25 21:51:13 2023 daemon.notice netifd: radio1 (20093):
Wed Jan 25 21:51:13 2023 daemon.notice netifd: radio1 (20093): Commands:
Wed Jan 25 21:51:13 2023 daemon.notice netifd: radio1 (20093): - list [<path>] List objects
Wed Jan 25 21:51:13 2023 daemon.notice netifd: radio1 (20093): - call <path> <method> [<message>] Call an object method
Wed Jan 25 21:51:13 2023 daemon.notice netifd: radio1 (20093): - subscribe <path> [<path>...] Subscribe to object(s) notifications
Wed Jan 25 21:51:13 2023 daemon.notice netifd: radio1 (20093): - listen [<path>...] Listen for events
Wed Jan 25 21:51:13 2023 daemon.notice netifd: radio1 (20093): - send <type> [<message>] Send an event
Wed Jan 25 21:51:13 2023 daemon.notice netifd: radio1 (20093): - wait_for <object> [<object>...] Wait for multiple objects to appear on ubus
Wed Jan 25 21:51:13 2023 daemon.notice netifd: radio1 (20093): - monitor Monitor ubus traffic
Wed Jan 25 21:51:13 2023 daemon.notice netifd: radio1 (20093):
Wed Jan 25 21:51:13 2023 daemon.notice netifd: radio1 (20093): Device setup failed: HOSTAPD_START_FAILED
Wed Jan 25 21:51:13 2023 daemon.notice netifd: Wireless device 'radio1' set retry=0
Wed Jan 25 21:51:13 2023 daemon.crit netifd: Wireless device 'radio1' setup failed, retry=0
Wed Jan 25 21:51:14 2023 daemon.notice netifd: Wireless device 'radio1' is now down
Wed Jan 25 21:51:15 2023 daemon.info dnsmasq[1]: read /etc/hosts - 12 names
Wed Jan 25 21:51:15 2023 daemon.info dnsmasq[1]: read /tmp/hosts/dhcp.cfg01411c - 4 names
Wed Jan 25 21:51:15 2023 daemon.info dnsmasq[1]: read /tmp/hosts/odhcpd - 4 names
Wed Jan 25 21:51:15 2023 daemon.info dnsmasq-dhcp[1]: read /etc/ethers - 0 addresses
Wed Jan 25 21:51:29 2023 daemon.notice hostapd: Configuration file: /var/run/hostapd-phy1.conf (phy phy1-ap0) --> new PHY
Wed Jan 25 21:51:29 2023 kern.info kernel: [ 4621.769191] br-lan: port 5(phy1-ap0) entered blocking state
Wed Jan 25 21:51:29 2023 kern.info kernel: [ 4621.769238] br-lan: port 5(phy1-ap0) entered disabled state
Wed Jan 25 21:51:29 2023 kern.info kernel: [ 4621.773863] device phy1-ap0 entered promiscuous mode
Wed Jan 25 21:51:29 2023 kern.info kernel: [ 4621.779238] br-lan: port 5(phy1-ap0) entered blocking state
Wed Jan 25 21:51:29 2023 kern.info kernel: [ 4621.784364] br-lan: port 5(phy1-ap0) entered forwarding state
Wed Jan 25 21:51:29 2023 daemon.notice hostapd: phy1-ap0: interface state UNINITIALIZED->COUNTRY_UPDATE
Wed Jan 25 21:51:29 2023 kern.info kernel: [ 4621.790042] br-lan: port 5(phy1-ap0) entered disabled state
Wed Jan 25 21:51:29 2023 daemon.err hostapd: Interface initialization failed
Wed Jan 25 21:51:29 2023 daemon.notice hostapd: phy1-ap0: interface state COUNTRY_UPDATE->DISABLED
Wed Jan 25 21:51:29 2023 daemon.notice hostapd: phy1-ap0: AP-DISABLED
Wed Jan 25 21:51:29 2023 daemon.err hostapd: phy1-ap0: Unable to setup interface.
Wed Jan 25 21:51:29 2023 daemon.notice hostapd: nl80211: deinit ifname=phy1-ap0 disabled_11b_rates=0
Wed Jan 25 21:51:30 2023 kern.info kernel: [ 4621.796932] device phy1-ap0 left promiscuous mode
Wed Jan 25 21:51:30 2023 kern.info kernel: [ 4621.801009] br-lan: port 5(phy1-ap0) entered disabled state
Wed Jan 25 21:51:30 2023 daemon.err hostapd: rmdir[ctrl_interface=/var/run/hostapd]: Permission denied
Wed Jan 25 21:51:30 2023 daemon.notice hostapd: phy1-ap0: CTRL-EVENT-TERMINATING
Wed Jan 25 21:51:30 2023 daemon.err hostapd: hostapd_free_hapd_data: Interface phy1-ap0 wasn't started
Wed Jan 25 21:51:30 2023 daemon.notice netifd: radio1 (20489): Command failed: ubus call hostapd config_add {"iface":"phy1-ap0", "config":"/var/run/hostapd-phy1.conf"} (Invalid argument)
Wed Jan 25 21:51:30 2023 daemon.notice netifd: radio1 (20489): Usage: ubus [<options>] <command> [arguments...]
Wed Jan 25 21:51:30 2023 daemon.notice netifd: radio1 (20489): Options:
Wed Jan 25 21:51:30 2023 daemon.notice netifd: radio1 (20489): -s <socket>: Set the unix domain socket to connect to
Wed Jan 25 21:51:30 2023 daemon.notice netifd: radio1 (20489): -t <timeout>: Set the timeout (in seconds) for a command to complete
Wed Jan 25 21:51:30 2023 daemon.notice netifd: radio1 (20489): -S: Use simplified output (for scripts)
Wed Jan 25 21:51:30 2023 daemon.notice netifd: radio1 (20489): -v: More verbose output
Wed Jan 25 21:51:30 2023 daemon.notice netifd: radio1 (20489): -m <type>: (for monitor): include a specific message type
Wed Jan 25 21:51:30 2023 daemon.notice netifd: radio1 (20489): (can be used more than once)
Wed Jan 25 21:51:30 2023 daemon.notice netifd: radio1 (20489): -M <r|t> (for monitor): only capture received or transmitted traffic
Wed Jan 25 21:51:30 2023 daemon.notice netifd: radio1 (20489):
Wed Jan 25 21:51:30 2023 daemon.notice netifd: radio1 (20489): Commands:
Wed Jan 25 21:51:30 2023 daemon.notice netifd: radio1 (20489): - list [<path>] List objects
Wed Jan 25 21:51:30 2023 daemon.notice netifd: radio1 (20489): - call <path> <method> [<message>] Call an object method
Wed Jan 25 21:51:30 2023 daemon.notice netifd: radio1 (20489): - subscribe <path> [<path>...] Subscribe to object(s) notifications
Wed Jan 25 21:51:30 2023 daemon.notice netifd: radio1 (20489): - listen [<path>...] Listen for events
Wed Jan 25 21:51:30 2023 daemon.notice netifd: radio1 (20489): - send <type> [<message>] Send an event
Wed Jan 25 21:51:30 2023 daemon.notice netifd: radio1 (20489): - wait_for <object> [<object>...] Wait for multiple objects to appear on ubus
Wed Jan 25 21:51:30 2023 daemon.notice netifd: radio1 (20489): - monitor Monitor ubus traffic
Wed Jan 25 21:51:30 2023 daemon.notice netifd: radio1 (20489):
Wed Jan 25 21:51:30 2023 daemon.notice netifd: radio1 (20489): Device setup failed: HOSTAPD_START_FAILED
Wed Jan 25 21:51:30 2023 daemon.notice netifd: Wireless device 'radio1' set retry=0
Wed Jan 25 21:51:30 2023 daemon.crit netifd: Wireless device 'radio1' setup failed, retry=0
Wed Jan 25 21:51:30 2023 daemon.notice netifd: Wireless device 'radio1' is now down
Wed Jan 25 21:51:31 2023 daemon.info dnsmasq[1]: read /etc/hosts - 12 names
Wed Jan 25 21:51:31 2023 daemon.info dnsmasq[1]: read /tmp/hosts/dhcp.cfg01411c - 4 names
Wed Jan 25 21:51:31 2023 daemon.info dnsmasq[1]: read /tmp/hosts/odhcpd - 4 names
Wed Jan 25 21:51:31 2023 daemon.info dnsmasq-dhcp[1]: read /etc/ethers - 0 addresses
Wed Jan 25 21:52:11 2023 daemon.notice hostapd: Configuration file: /var/run/hostapd-phy1.conf (phy phy1-ap0) --> new PHY
Wed Jan 25 21:52:11 2023 kern.info kernel: [ 4663.372865] br-lan: port 5(phy1-ap0) entered blocking state
Wed Jan 25 21:52:11 2023 kern.info kernel: [ 4663.372915] br-lan: port 5(phy1-ap0) entered disabled state
Wed Jan 25 21:52:11 2023 kern.info kernel: [ 4663.377483] device phy1-ap0 entered promiscuous mode
Wed Jan 25 21:52:11 2023 kern.info kernel: [ 4663.382997] br-lan: port 5(phy1-ap0) entered blocking state
Wed Jan 25 21:52:11 2023 kern.info kernel: [ 4663.388022] br-lan: port 5(phy1-ap0) entered forwarding state
Wed Jan 25 21:52:11 2023 daemon.notice hostapd: phy1-ap0: interface state UNINITIALIZED->COUNTRY_UPDATE
Wed Jan 25 21:52:11 2023 daemon.err hostapd: Interface initialization failed
Wed Jan 25 21:52:11 2023 daemon.notice hostapd: phy1-ap0: interface state COUNTRY_UPDATE->DISABLED
Wed Jan 25 21:52:11 2023 daemon.notice hostapd: phy1-ap0: AP-DISABLED
Wed Jan 25 21:52:11 2023 daemon.err hostapd: phy1-ap0: Unable to setup interface.
Wed Jan 25 21:52:11 2023 daemon.notice hostapd: nl80211: deinit ifname=phy1-ap0 disabled_11b_rates=0
Wed Jan 25 21:52:11 2023 kern.info kernel: [ 4663.393663] br-lan: port 5(phy1-ap0) entered disabled state
Wed Jan 25 21:52:11 2023 kern.info kernel: [ 4663.400467] device phy1-ap0 left promiscuous mode
Wed Jan 25 21:52:11 2023 kern.info kernel: [ 4663.404804] br-lan: port 5(phy1-ap0) entered disabled state
Wed Jan 25 21:52:11 2023 daemon.err hostapd: rmdir[ctrl_interface=/var/run/hostapd]: Permission denied
Wed Jan 25 21:52:11 2023 daemon.notice hostapd: phy1-ap0: CTRL-EVENT-TERMINATING
Wed Jan 25 21:52:11 2023 daemon.err hostapd: hostapd_free_hapd_data: Interface phy1-ap0 wasn't started
Wed Jan 25 21:52:11 2023 daemon.notice netifd: radio1 (20861): Command failed: ubus call hostapd config_add {"iface":"phy1-ap0", "config":"/var/run/hostapd-phy1.conf"} (Invalid argument)
Wed Jan 25 21:52:11 2023 daemon.notice netifd: radio1 (20861): Usage: ubus [<options>] <command> [arguments...]
Wed Jan 25 21:52:11 2023 daemon.notice netifd: radio1 (20861): Options:
Wed Jan 25 21:52:11 2023 daemon.notice netifd: radio1 (20861): -s <socket>: Set the unix domain socket to connect to
Wed Jan 25 21:52:11 2023 daemon.notice netifd: radio1 (20861): -t <timeout>: Set the timeout (in seconds) for a command to complete
Wed Jan 25 21:52:11 2023 daemon.notice netifd: radio1 (20861): -S: Use simplified output (for scripts)
Wed Jan 25 21:52:11 2023 daemon.notice netifd: radio1 (20861): -v: More verbose output
Wed Jan 25 21:52:11 2023 daemon.notice netifd: radio1 (20861): -m <type>: (for monitor): include a specific message type
Wed Jan 25 21:52:11 2023 daemon.notice netifd: radio1 (20861): (can be used more than once)
Wed Jan 25 21:52:11 2023 daemon.notice netifd: radio1 (20861): -M <r|t> (for monitor): only capture received or transmitted traffic
Wed Jan 25 21:52:11 2023 daemon.notice netifd: radio1 (20861):
Wed Jan 25 21:52:11 2023 daemon.notice netifd: radio1 (20861): Commands:
Wed Jan 25 21:52:11 2023 daemon.notice netifd: radio1 (20861): - list [<path>] List objects
Wed Jan 25 21:52:11 2023 daemon.notice netifd: radio1 (20861): - call <path> <method> [<message>] Call an object method
Wed Jan 25 21:52:11 2023 daemon.notice netifd: radio1 (20861): - subscribe <path> [<path>...] Subscribe to object(s) notifications
Wed Jan 25 21:52:11 2023 daemon.notice netifd: radio1 (20861): - listen [<path>...] Listen for events
Wed Jan 25 21:52:11 2023 daemon.notice netifd: radio1 (20861): - send <type> [<message>] Send an event
Wed Jan 25 21:52:11 2023 daemon.notice netifd: radio1 (20861): - wait_for <object> [<object>...] Wait for multiple objects to appear on ubus
Wed Jan 25 21:52:11 2023 daemon.notice netifd: radio1 (20861): - monitor Monitor ubus traffic
Wed Jan 25 21:52:11 2023 daemon.notice netifd: radio1 (20861):
Wed Jan 25 21:52:11 2023 daemon.notice netifd: radio1 (20861): Device setup failed: HOSTAPD_START_FAILED
Wed Jan 25 21:52:11 2023 daemon.notice netifd: Wireless device 'radio1' set retry=0
Wed Jan 25 21:52:11 2023 daemon.crit netifd: Wireless device 'radio1' setup failed, retry=0
Wed Jan 25 21:52:11 2023 daemon.notice netifd: Wireless device 'radio1' is now down
Wed Jan 25 21:52:29 2023 daemon.notice hostapd: Configuration file: /var/run/hostapd-phy1.conf (phy phy1-ap0) --> new PHY
Wed Jan 25 21:52:29 2023 kern.info kernel: [ 4681.630362] br-lan: port 5(phy1-ap0) entered blocking state
Wed Jan 25 21:52:29 2023 kern.info kernel: [ 4681.630411] br-lan: port 5(phy1-ap0) entered disabled state
Wed Jan 25 21:52:29 2023 kern.info kernel: [ 4681.635049] device phy1-ap0 entered promiscuous mode
Wed Jan 25 21:52:29 2023 kern.info kernel: [ 4681.640416] br-lan: port 5(phy1-ap0) entered blocking state
Wed Jan 25 21:52:29 2023 kern.info kernel: [ 4681.645545] br-lan: port 5(phy1-ap0) entered forwarding state
Wed Jan 25 21:52:29 2023 daemon.notice hostapd: phy1-ap0: interface state UNINITIALIZED->COUNTRY_UPDATE
Wed Jan 25 21:52:29 2023 kern.info kernel: [ 4681.651041] br-lan: port 5(phy1-ap0) entered disabled state
Wed Jan 25 21:52:29 2023 daemon.notice hostapd: phy1-ap0: interface state COUNTRY_UPDATE->DFS
Wed Jan 25 21:52:29 2023 daemon.notice hostapd: phy1-ap0: DFS-CAC-START freq=5720 chan=144 sec_chan=-1, width=1, seg0=138, seg1=0, cac_time=60s
Wed Jan 25 21:52:30 2023 daemon.notice netifd: Wireless device 'radio1' is now up
Wed Jan 25 21:52:31 2023 daemon.info dnsmasq[1]: read /etc/hosts - 12 names
Wed Jan 25 21:52:31 2023 daemon.info dnsmasq[1]: read /tmp/hosts/dhcp.cfg01411c - 4 names
Wed Jan 25 21:52:31 2023 daemon.info dnsmasq[1]: read /tmp/hosts/odhcpd - 4 names
Wed Jan 25 21:52:31 2023 daemon.info dnsmasq-dhcp[1]: read /etc/ethers - 0 addresses
Wed Jan 25 21:53:32 2023 daemon.notice hostapd: phy1-ap0: DFS-CAC-COMPLETED success=1 freq=5720 ht_enabled=0 chan_offset=0 chan_width=3 cf1=5690 cf2=0
Wed Jan 25 21:53:32 2023 kern.info kernel: [ 4744.204810] IPv6: ADDRCONF(NETDEV_CHANGE): phy1-ap0: link becomes ready
Wed Jan 25 21:53:32 2023 kern.info kernel: [ 4744.205013] br-lan: port 5(phy1-ap0) entered blocking state
Wed Jan 25 21:53:32 2023 kern.info kernel: [ 4744.210244] br-lan: port 5(phy1-ap0) entered forwarding state
Wed Jan 25 21:53:32 2023 daemon.notice netifd: Network device 'phy1-ap0' link is up
Wed Jan 25 21:53:32 2023 daemon.notice hostapd: phy1-ap0: interface state DFS->ENABLED
Wed Jan 25 21:53:32 2023 daemon.notice hostapd: phy1-ap0: AP-ENABLED
To jako ciekawostka. Zaczęło działać więc nie wiem co go bolało...
- pepe2k
- Użytkownik
- Nieaktywny
Odp: Xiaomi AX3600
Gdzieś jest babol w tym zmienionym skrypcie konfigurującym radia... też to już kilka razy widziałem i na razie nie udało się znaleźć.
Odp: Xiaomi AX3600
smereka napisał/a:
No jakieś komedie się dzieją. Ustawiłem kanał 100 i działa, ustawiłem 149 i działa.
Na 149 kanale to chyba raczej nie udało Ci się odpalić 160MHz...
smereka napisał/a:
To jako ciekawostka. Zaczęło działać więc nie wiem co go bolało...
Jest ten problem zgłoszony: https://github.com/openwrt/openwrt/issues/11246
Odp: Xiaomi AX3600
frutis napisał/a:
A na oprogramowaniu od Xiaomi działało Ci 160MHz? Albo na jakimś innym routerze czy Ci działa?
dziala 160 MHz na Linksys e8450 na kanale 64 kraj Haiti
ASUS ax4200 & Xiaomi Redmi ax6000 dumbAP @ openwrt 24.10 & Huawei e5786 jako backup
Odp: Xiaomi AX3600
sebastan napisał/a:
Nie, nie musisz wracać do chińskiego, choć możesz.
W tej sytuacji, w jakiej jesteś musisz po pierwsze ustalić, której partycji teraz używasz.
fw_printenv flag_boot_rootfsW zależności, czy odpowiedź będzie 0 czy 1 to wiesz, że musisz sformatować tą drugą partycję:
Jeśli 1 to
ubiformat /dev/mtd12 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi -s 2048 -O 2048 && fw_setenv flag_boot_rootfs 0 && fw_setenv flag_last_success 0 && rebootJeśli 0 to
ubiformat /dev/mtd13 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi -s 2048 -O 2048 && fw_setenv flag_boot_rootfs 0 && fw_setenv flag_last_success 0 && rebootWcześniej musisz rzecz jasna wrzucić initramfs-factory.ubi do /tmp.
Może być to:
https://github.com/robimarko/openwrt/releases/download/ipq807x-2023-01-14-1709/openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubiWtedy restart i powinno Ci się uruchomić w initramfs
Wtedy robisz już normalne sysupgrade np. tym:
https://github.com/robimarko/openwrt/releases/download/ipq807x-2023-01-14-1709/openwrt-ipq807x-generic-xiaomi_ax3600-squashfs-sysupgrade.binPodlinkowane wersje to 3a2144f autorstwa robimarko.
Instrukcje różne tu :
https://openwrt.org/inbox/toh/xiaomi/xiaomi_ax3600#installation
Czy po poszerzeniu partycji i i wgraniu sysupgrade można uruchomić oprogramowanie z drugiej partycji?
Teraz jestem na partycji 0 ( rozszerzona) chcę wrócić do partycji 1 uruchomić oprogramowanie na niej?
Odp: Xiaomi AX3600
Jeśli poszerzyłeś partycję, no to masz już tylko jedną.
366 2023-01-30 17:47:32 (edytowany przez jurekcostam 2023-01-30 17:47:52)
Odp: Xiaomi AX3600
Witam
mam zainstalowany obraz SNAPSHOT r21922-6e428a8490 z LuCI chciałem zrobić aktualizację ale wywali mi bład:
root@OpenWrt:~# sysupgrade -n /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-squashf
s-sysupgrade.bin
Mon Jan 30 17:31:30 CET 2023 upgrade: The device is supported, but this image is incompatible for sysupgrade based on the image version (2.0->1.0).
Image check failed.
root@OpenWrt:~#
Próbowałem też aktualizację firmware przez LuCI ale też nie można ten sam błąd.
Nawet jak dam" wymuś uaktualnienie" niby obraz się ładuje ale po restarcie wstaje nadal bierzący obraz.
Coś robię nie tak?
Odp: Xiaomi AX3600
Skąd miałeś poprzedni obraz? Stanowczo że chce go zaktualizować z -F, z wymuszeniem. Ale jak piszesz - zostawia w spokoju, więc wygląda tak jak byś musiał mu wgrać od początku factory.
Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.
368 2023-01-30 20:15:11 (edytowany przez jurekcostam 2023-01-30 20:16:34)
Odp: Xiaomi AX3600
Poprzednio miałem obraz @robimako ten z 14stycznia, później zainstalowałem ze strony OpenWrt zainstalował się z wymuszeniem. Tego najnowszego z OpenWrt już nie mogę.
Odp: Xiaomi AX3600
Przywróć oryginał od xiaomi i wgraj jeszcze raz.
Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.
Odp: Xiaomi AX3600
Nie wiem czy mogę mam już zrobioną poszerzaną partycje.
Odp: Xiaomi AX3600
Eh, chyba właśnie sobie odpowiedziałeś czemu nie wchodzi z wymuszeniem 
Chyba skrypty od sysupgarde albo nie wiedzą co zrobić w takim przypadku albo się wykładają. Na 90% przypuszczam że to jest problemem.
Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.
372 2023-01-31 11:16:11 (edytowany przez sebastan 2023-01-31 11:19:18)
Odp: Xiaomi AX3600
Wersja została podniesiona do 2.0 przez robimarko po poszerzeniu partycji, właśnie po to by ludzie nie uwalali tunerów i widzieli to ostrzeżenie.
Jednak jeśli partycję już poszerzyłeś i chcesz zrobić sysupgrade do aktualnej wersji, to możesz to zrobić. Ja to zrobiłem poleceniem przez ssh na zmianę wersji z 2.0 na 1.0 i wtedy nie musisz wymuszenia.
PS. Poszerzona partycja też Ci nie przeszkadza, nawet gdybyś musiał wrócić do chińczyka. Przy sysupgrade proponuje się też stop wpad, ale ja zawsze robię dwukrotnie i za drugim razem zawsze wchodzi bez stop wpad. Pamiętaj też, że wersje aktualne są bez luci, żebyś się nie spłoszył, że coś poszło nie tak, bo Ci się luci nie pokaże.
373 2023-01-31 11:20:10 (edytowany przez jurekcostam 2023-01-31 11:24:28)
Odp: Xiaomi AX3600
Możesz napisać jak to zrobić chodzi o polecenia. Jeżeli chodzi o Luci to wiem bo już robiłem aktualizację sysupgrade i wcześniej poszło
Odp: Xiaomi AX3600
uci set system.@system[0].compat_version="1.0"
uci commit system375 2023-01-31 11:37:38 (edytowany przez jurekcostam 2023-01-31 11:38:14)
Odp: Xiaomi AX3600
I później już sysupgrade -n .... ?
Posty: 351 do 375 z 1,198
Strony Poprzednia 1 … 13 14 15 16 17 … 48 Następna
Zaloguj się lub zarejestruj by napisać odpowiedź
eko.one.pl → Sprzęt / Hardware → Xiaomi AX3600
Forum oparte o PunBB, wspierane przez Informer Technologies, Inc