1 Temat przez smereka (edytowany przez smereka 2023-01-31 20:55:24)

  • Zarejestrowany: 2014-07-09
  • Posty: 2,443

Temat: netgear wnap320 openwrt?

Dobra znalazłem chwilę żeby po testować czy uda się zapodanie mu openwrt. Wypatroszyłem go. Później może wstawię foty dla potomnych. Wpiąłem się serialem. Zrobiłem tak jak poniżej. Macie też logi:

Welcome to SDK.

Have a lot of fun...

parter login:

U-Boot 1.1.4 dni-1.09 (Jul  1 2010 - 11:39:24)

AP94 (ar7100) U-boot 0.0.12
DRAM:  b8050000: 0xc0140180
128 MB
Top of RAM usable for U-Boot at: 88000000
Reserving 228k for U-Boot at: 87fc4000
Reserving 192k for malloc() at: 87f94000
Reserving 56 Bytes for Board Info at: 87f93fc8
Reserving 36 Bytes for Global Data at: 87f93fa4
Reserving 128k for boot params() at: 87f73fa4
Stack Pointer at: 87f73f88
Now running in RAM - U-Boot at: 87fc4000
id read 0x100000ff
flash size 8MB, sector count = 128
Flash:  8 MB
In:    serial
Out:   serial
Err:   serial
Net:   ag7100_enet_initialize...
No valid address in Flash. Using fixed address
: cfg1 0xf cfg2 0x7014
 VSCXXX Found 0  unit 0:0  phy_addr: 1  id: 004dd04e
PHY:   Atheros AR8021
eth0: 00:03:7f:09:0b:ad
eth0 up
eth0
Manu data is valid!
### main_loop entered: bootdelay=4

### main_loop: bootcmd="bootm 0xbf050000"
Enter SPACE to drop into boot loader:  0
ar7100> setenv ipaddr 192.168.1.1
ar7100> setenv serverip 192.168.1.42
ar7100> saveenv
Saving Environment to Flash...
Protect off BF040000 ... BF04FFFF
Un-Protecting sectors 4..4 in bank 1
Un-Protected 1 sectors
Erasing Flash...Erase Flash from 0xbf040000 to 0xbf04ffff in Bank # 1
First 0x4 last 0x4 sector size 0x10000                                                                                                                                                                                                      4
Erased 1 sectors
Writing to Flash... write addr: bf040000
done
Protecting sectors 4..4 in bank 1
Protected 1 sectors
ar7100> reset

Resetting...

U-Boot 1.1.4 dni-1.09 (Jul  1 2010 - 11:39:24)

AP94 (ar7100) U-boot 0.0.12
DRAM:  b8050000: 0xc0140180
128 MB
Top of RAM usable for U-Boot at: 88000000
Reserving 228k for U-Boot at: 87fc4000
Reserving 192k for malloc() at: 87f94000
Reserving 56 Bytes for Board Info at: 87f93fc8
Reserving 36 Bytes for Global Data at: 87f93fa4
Reserving 128k for boot params() at: 87f73fa4
Stack Pointer at: 87f73f88
Now running in RAM - U-Boot at: 87fc4000
id read 0x100000ff
flash size 8MB, sector count = 128
Flash:  8 MB
In:    serial
Out:   serial
Err:   serial
Net:   ag7100_enet_initialize...
No valid address in Flash. Using fixed address
: cfg1 0xf cfg2 0x7014
 VSCXXX Found 0  unit 0:0  phy_addr: 1  id: 004dd04e
PHY:   Atheros AR8021
eth0: 00:03:7f:09:0b:ad
eth0 up
eth0
Manu data is valid!
### main_loop entered: bootdelay=4

### main_loop: bootcmd="bootm 0xbf050000"
Enter SPACE to drop into boot loader:  0
ar7100> tftpboot 0x81000000 1.bin
Trying eth0
Using eth0 device
TFTP from server 192.168.1.42; our IP address is 192.168.1.1
Filename '1.bin'.
Load address: 0x81000000
Loading: #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         ######
done
Bytes transferred = 18332916 (117bcf4 hex)
ar7100> bootm 0x81000000
## Booting image at 81000000 ...
   Image Name:   MIPS OpenWrt Linux-5.10.120
   Created:      2022-06-10   7:20:21 UTC
   Image Type:   MIPS Linux Kernel Image (uncompressed)
   Data Size:    18332852 Bytes = 17.5 MB
   Load Address: 80060000
   Entry Point:  80060000
   Verifying Checksum ... OK
OK
No initrd
## Transferring control to Linux (at address 80060000) ...
## Giving linux memsize in bytes, 134217728

Starting kernel ...

[    0.000000] Linux version 5.10.120 (builder@buildhost) (mips-openwrt-linux-musl-gcc (OpenWrt GCC 11.2.0 r19426-2b1941e47d) 11.2.0, GNU ld (GNU Binutils) 2.37) #0 Fri Jun 10 07:20:21 2022
[    0.000000] printk: bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
[    0.000000] MIPS: machine is Netgear WNDAP360
[    0.000000] SoC: Atheros AR7161 rev 2
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 32480
[    0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 110600K/131072K available (5844K kernel code, 606K rwdata, 744K rodata, 11740K init, 210K bss, 20472K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS: 51
[    0.000000] CPU clock: 680.000 MHz
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 5621354254 ns
[    0.000008] sched_clock: 32 bits at 340MHz, resolution 2ns, wraps every 6316128254ns
[    0.092880] Calibrating delay loop... 452.19 BogoMIPS (lpj=2260992)
[    0.227858] pid_max: default: 32768 minimum: 301
[    0.283296] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.370793] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.465395] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build
[    0.559537] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.677279] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[    0.758641] pinctrl core: initialized pinctrl subsystem
[    0.825294] NET: Registered protocol family 16
[    0.879146] thermal_sys: Registered thermal governor 'step_wise'
[    1.182296] PCI host bridge /ahb/apb/pcie-controller@17010000 ranges:
[    1.331393]  MEM 0x0000000010000000..0x0000000016ffffff
[    1.393931]   IO 0x0000000000000000..0x0000000000000000
[    1.493285] PCI host bridge to bus 0000:00
[    1.542328] pci_bus 0000:00: root bus resource [mem 0x10000000-0x16ffffff]
[    1.624599] pci_bus 0000:00: root bus resource [io  0x0000]
[    1.691324] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    1.772620] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    1.867885] pci 0000:00:11.0: [168c:ff1d] type 00 class 0x020000
[    1.939814] pci 0000:00:11.0: reg 0x10: [mem 0x00000000-0x0000ffff]
[    2.016252] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[    2.095460] pci 0000:00:11.0: BAR 0: assigned [mem 0x10000000-0x1000ffff]
[    2.182738] clocksource: Switched to clocksource MIPS
[    2.244331] NET: Registered protocol family 2
[    2.296728] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
[    2.384001] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[    2.484078] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    2.575738] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    2.660150] TCP: Hash tables configured (established 1024 bind 1024)
[    2.736378] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[    2.814541] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[    2.898165] NET: Registered protocol family 1
[    2.950313] PCI: CLS 0 bytes, default 32
[    3.180778] workingset: timestamp_bits=14 max_order=15 bucket_order=1
[    3.262299] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    3.332193] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    3.450677] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[    3.541072] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    3.619363] printk: console [ttyS0] disabled
[    3.670590] 18020000.uart: ttyS0 at MMIO 0x18020000 (irq = 10, base_baud = 10625000) is a 16550A
▒޳▒▒i▒▒i▒▒▒m)▒QJ▒       j! `▒ ▒▒▒Yt▒▒(▒▒▒uQH▒▒!▒& ]{▒ËES▒I▒▒▒▒u▒].E
                                                                   ɋ▒▒O:▒▒赇 ZڕI▒▒▒^▒*Pi▒Z▒▒8?▒E▒▒▒▒璇T▒S▒▒_▒_y}~TX뿁▒ ް▒B▒▒▒P▒wZEW▒▒tM▒▒_▒▒▒`j▒▒▒▒h+%▒▒▒▒▒▒▒▒d▒U▒▒▒u>j▒▒PEܘ▒▒▒EP`▒P▒W▒^▒       `\▒▒mPE▒▒P+▒e▒▒▒ ▒|Sm▒(▒▒▒x,Qـ▒<▒K▒

Dioda pomarańczowa od zasilania po tych ostatnich logach jeszcze kilkanaście sekund sobie mruga potem przestaje. Jak wyjmę przewód gasną 2 diody od sieci i ta druga oznaczona w kształcie wirujących strzałek.

Te 1.bin co mu zapodałem to:

openwrt-22.03.0-rc4-ath79-generic-netgear_wndap360-initramfs-kernel.bin


Na forum openwrt odnośnie modelu wndap360 piszą, że trzeba sobie skompilować kernela. Ja tego nie umiem zrobić. Cezary mógłbyś mi testowego wrzucić? Chyba, ze coś już po powyższych logach można stwierdzić....

2 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 115,970

Odp: netgear wnap320 openwrt?

Tzn co trzeba kompilować?  Initramfs dla 360 masz u mnie, 320 chyba nie jest wspierana.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

3 Odpowiedź przez smereka

  • Zarejestrowany: 2014-07-09
  • Posty: 2,443

Odp: netgear wnap320 openwrt?

dasz linka do Twojego initramfs 360 bo szukam i szukam...

4 Odpowiedź przez smereka (edytowany przez smereka 2023-01-31 20:56:06)

  • Zarejestrowany: 2014-07-09
  • Posty: 2,443

Odp: netgear wnap320 openwrt?

Dobra znalazłem. Działa hura. Wszystkie diody działają jak trzeba. Lan zestawia się na 1gbit i wifi też śmiga. W końcu jedyny prawdziwy soft na dziadku. Teraz wszystkie pozostałe 4 przemagluję. Ale elegancko. W sumie dziwne jakby miało nie działac przecież to to samo co wndap360 tylko wykastrowane z wifi na 5GHz wink

Macie log w grania:

U-Boot 1.1.4 dni-1.09 (Jul  1 2010 - 11:39:24)

AP94 (ar7100) U-boot 0.0.12
DRAM:  b8050000: 0xc0140180
128 MB
Top of RAM usable for U-Boot at: 88000000
Reserving 228k for U-Boot at: 87fc4000
Reserving 192k for malloc() at: 87f94000
Reserving 56 Bytes for Board Info at: 87f93fc8
Reserving 36 Bytes for Global Data at: 87f93fa4
Reserving 128k for boot params() at: 87f73fa4
Stack Pointer at: 87f73f88
Now running in RAM - U-Boot at: 87fc4000
id read 0x100000ff
flash size 8MB, sector count = 128
Flash:  8 MB
In:    serial
Out:   serial
Err:   serial
Net:   ag7100_enet_initialize...
No valid address in Flash. Using fixed address
: cfg1 0xf cfg2 0x7014
 VSCXXX Found 0  unit 0:0  phy_addr: 1  id: 004dd04e
PHY:   Atheros AR8021
eth0: 00:03:7f:09:0b:ad
eth0 up
eth0
Manu data is valid!
### main_loop entered: bootdelay=4

### main_loop: bootcmd="bootm 0xbf050000"
Enter SPACE to drop into boot loader:  0
ar7100> setenv ipaddr 192.168.1.1
ar7100> setenv serverip 192.168.1.42
ar7100> saveenv
Saving Environment to Flash...
Protect off BF040000 ... BF04FFFF
Un-Protecting sectors 4..4 in bank 1
Un-Protected 1 sectors
Erasing Flash...Erase Flash from 0xbf040000 to 0xbf04ffff in Bank # 1
First 0x4 last 0x4 sector size 0x10000                                                                                                                                                                                                      4
Erased 1 sectors
Writing to Flash... write addr: bf040000
done
Protecting sectors 4..4 in bank 1
Protected 1 sectors
ar7100> reset

Resetting...

U-Boot 1.1.4 dni-1.09 (Jul  1 2010 - 11:39:24)

AP94 (ar7100) U-boot 0.0.12
DRAM:  b8050000: 0xc0140180
128 MB
Top of RAM usable for U-Boot at: 88000000
Reserving 228k for U-Boot at: 87fc4000
Reserving 192k for malloc() at: 87f94000
Reserving 56 Bytes for Board Info at: 87f93fc8
Reserving 36 Bytes for Global Data at: 87f93fa4
Reserving 128k for boot params() at: 87f73fa4
Stack Pointer at: 87f73f88
Now running in RAM - U-Boot at: 87fc4000
id read 0x100000ff
flash size 8MB, sector count = 128
Flash:  8 MB
In:    serial
Out:   serial
Err:   serial
Net:   ag7100_enet_initialize...
No valid address in Flash. Using fixed address
: cfg1 0xf cfg2 0x7014
 VSCXXX Found 0  unit 0:0  phy_addr: 1  id: 004dd04e
PHY:   Atheros AR8021
eth0: 00:03:7f:09:0b:ad
eth0 up
eth0
Manu data is valid!
### main_loop entered: bootdelay=4

### main_loop: bootcmd="bootm 0xbf050000"
Enter SPACE to drop into boot loader:  0
ar7100> tftpboot 0x81000000 1.bin
Trying eth0
Using eth0 device
TFTP from server 192.168.1.42; our IP address is 192.168.1.1
Filename '1.bin'.
Load address: 0x81000000
Loading: #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         ###############################################
done
Bytes transferred = 4233506 (409922 hex)
ar7100> bootm 0x81000000
## Booting image at 81000000 ...
   Image Name:   MIPS OpenWrt Linux-4.14.275
   Created:      2022-04-20  10:38:55 UTC
   Image Type:   MIPS Linux Kernel Image (gzip compressed)
   Data Size:    4233442 Bytes =  4 MB
   Load Address: 80060000
   Entry Point:  80060000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80060000) ...
## Giving linux memsize in bytes, 134217728

Starting kernel ...

[    0.000000] Linux version 4.14.275 (cezary@eko.one.pl) (gcc version 7.5.0 (OpenWrt GCC 7.5.0 r11261-3f5fecfd33)) #0 Wed Apr 20 10:38:55 2022
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
[    0.000000] SoC: Atheros AR7161 rev 2
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] random: get_random_bytes called from 0x804f4740 with crng_init=0
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line:  board=WNDAP360 console=ttyS0,9600 mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,7744k(firmware),64k(nvram)ro,64k(art)ro rootfstype=squashfs noinitrd
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 122372K/131072K available (3969K kernel code, 191K rwdata, 516K rodata, 2224K init, 212K bss, 8700K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS: 51
[    0.000000] Clocks: CPU:680.000MHz, DDR:340.000MHz, AHB:170.000MHz, Ref:40.000MHz
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 5621354254 ns
[    0.000008] sched_clock: 32 bits at 340MHz, resolution 2ns, wraps every 6316128254ns
[    0.092819] Calibrating delay loop... 452.19 BogoMIPS (lpj=2260992)
[    0.227861] pid_max: default: 32768 minimum: 301
[    0.283321] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.362469] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.448764] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.566523] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.640446] NET: Registered protocol family 16
[    0.694716] MIPS: machine is NETGEAR WNDAP360
[    1.290610] registering PCI controller with io_map_base unset
[    1.368725] PCI host bridge to bus 0000:00
[    1.417816] pci_bus 0000:00: root bus resource [mem 0x10000000-0x16ffffff]
[    1.500105] pci_bus 0000:00: root bus resource [io  0x0000]
[    1.566830] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    1.648128] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    1.743016] pci 0000:00:11.0: fixup device configuration
[    1.808033] pci 0000:00:11.0: BAR 0: assigned [mem 0x10000000-0x1000ffff]
[    1.891967] clocksource: Switched to clocksource MIPS
[    1.953298] NET: Registered protocol family 2
[    2.005581] IP idents hash table entries: 2048 (order: 2, 16384 bytes)
[    2.084419] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    2.167820] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    2.243875] TCP: Hash tables configured (established 1024 bind 1024)
[    2.320091] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    2.389944] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    2.465122] NET: Registered protocol family 1
[    4.211976] random: fast init done
[    5.372597] Crashlog allocated RAM at address 0x3f00000
[    5.436297] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[    5.517691] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    5.587495] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    5.766463] io scheduler noop registered
[    5.813387] io scheduler deadline registered (default)
[    5.875204] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    5.953102] console [ttyS0] disabled
[    6.015894] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 10625000) is a 16550A
[    6.120110] console [ttyS0] enabled
[    6.120110] console [ttyS0] enabled
[    6.203544] bootconsole [early0] disabled
[    6.203544] bootconsole [early0] disabled
[    6.304790] m25p80 spi0.0: found mx25l6405d, expected m25p80
[    6.373235] m25p80 spi0.0: mx25l6405d (8192 Kbytes)
[    6.431660] 5 cmdlinepart partitions found on MTD device spi0.0
[    6.502562] Creating 5 MTD partitions on "spi0.0":
[    6.559976] 0x000000000000-0x000000040000 : "u-boot"
[    6.638986] 0x000000040000-0x000000050000 : "u-boot-env"
[    6.722096] 0x000000050000-0x0000007e0000 : "firmware"
[    6.797342] 2 uimage-fw partitions found on MTD device firmware
[    6.868296] 0x000000050000-0x000000760000 : "kernel"
[    6.928388] 0x000000760000-0x0000007e0000 : "rootfs"
[    6.988516] mtd: device 4 (rootfs) set to be root filesystem
[    7.056382] mtdsplit: no squashfs found in "rootfs"
[    7.134098] 0x0000007e0000-0x0000007f0000 : "nvram"
[    7.212033] 0x0000007f0000-0x000000800000 : "art"
[    7.653425] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:01 [uid=004dd04e, driver=Generic PHY]
[    7.763441] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode: rgmii
[    7.838951] NET: Registered protocol family 10
[    7.895724] Segment Routing with IPv6
[    7.939647] NET: Registered protocol family 17
[    7.992928] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    8.148699] 8021q: 802.1Q VLAN Support v1.8
[    8.200120] hctosys: unable to open rtc device (rtc0)
[    8.267475] Freeing unused kernel memory: 2224K
[    8.321704] This architecture does not have kernel memory protection.
[    8.411801] init: Console is alive
[    8.452887] init: - watchdog -
[    8.508148] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    8.591284] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    8.688246] init: - preinit -
[    8.876042] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[    8.964791] random: procd: uninitialized urandom read (4 bytes read)
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[   12.159906] procd: - early -
[   12.195099] procd: - watchdog -
[   12.796387] procd: - watchdog -
[   12.834336] procd: - ubus -
[   12.873755] random: ubusd: uninitialized urandom read (4 bytes read)
[   12.950928] random: ubusd: uninitialized urandom read (4 bytes read)
[   13.027518] random: ubusd: uninitialized urandom read (4 bytes read)
[   13.104525] procd: - init -
Please press Enter to activate this console.
[   13.523664] kmodloader: loading kernel modules from /etc/modules.d/*
[   13.686837] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   13.828123] Loading modules backported from Linux version v4.19.237-0-ga6e4a1818efa
[   13.919996] Backport generated by backports.git v4.19.237-1-0-gffb89fd9
[   14.087132] urngd: v1.0.2 started.
[   14.173854] ip_tables: (C) 2000-2006 Netfilter Core Team
[   14.308237] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
[   14.442017] random: crng init done
[   14.482781] random: 6 urandom warning(s) missed due to ratelimiting
[   14.605980] xt_time: kernel timezone is -0000
[   14.726245] PPP generic driver version 2.4.2
[   14.832654] NET: Registered protocol family 24
[   14.982937] pci 0000:00:11.0: using irq 40 for pin 1
[   15.042430] PCI: Enabling device 0000:00:11.0 (0000 -> 0002)
[   15.115034] ath: phy0: Ignoring endianness difference in EEPROM magic bytes.
[   15.217107] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xb0000000, irq=40
[   15.862307] kmodloader: done loading kernel modules from /etc/modules.d/*
[   26.205580] eth0: link up (1000Mbps/Full duplex)
[   26.272324] br-lan: port 1(eth0) entered blocking state
[   26.334942] br-lan: port 1(eth0) entered disabled state
[   26.397806] device eth0 entered promiscuous mode
[   26.523641] br-lan: port 1(eth0) entered blocking state
[   26.586245] br-lan: port 1(eth0) entered forwarding state
[   26.651092] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   27.282085] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   91.042108] eth0: link down
[   91.076092] br-lan: port 1(eth0) entered disabled state
[  183.602455] eth0: link up (1000Mbps/Full duplex)
[  183.658065] br-lan: port 1(eth0) entered blocking state
[  183.720635] br-lan: port 1(eth0) entered forwarding state



BusyBox v1.30.1 () built-in shell (ash)

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 -----------------------------------------------------------------------------
 |                                                                           |
 | OpenWrt 19.07-SNAPSHOT, r11430-ecbbb373ed                                 |
 |                                                                           |
 | Build time: 2022-05-13 22:57 CEST                                         |
 | Cezary Jackiewicz, [url]https://eko.one.pl[/url]                                     |
 |                                                                           |
 -----------------------------------------------------------------------------
 | Machine: NETGEAR WNDAP360                                                 |
 | Uptime: 0d, 00:04:48                                                      |
 | Load: 0.04 0.07 0.03                                                      |
 | Flash:                                                                    |
 | Memory: total: 121.7MB, free: 113.0MB, used: 7%                           |
 | Leases: 1                                                                 |
 | lan: static, 192.168.1.1                                                  |
 -----------------------------------------------------------------------------
 === WARNING! ================================================================
 There is no root password defined on this device!
 Use the "passwd" command to set up a new password
 in order to prevent unauthorized SSH logins.
 -----------------------------------------------------------------------------
root@OpenWrt:/# sysupgrade -n /tmp/1.bin
Image metadata not found
Commencing upgrade. Closing all shell sessions.
Watchdog handover: fd=3
- watchdog -
killall: telnetd: no process kilSending TERM to remaining processes ... ntpd dnsmasq ubusd urngd logd netifd odhcpd
Sending KILL to remaining processes ...
Performing system upgrade...
Unlocking firmware ...

Writing from <stdin> to firmware ...
Upgrade completed
Rebooting system[  370.980984] reboot: Restarting system


U-Boot 1.1.4 dni-1.09 (Jul  1 2010 - 11:39:24)

AP94 (ar7100) U-boot 0.0.12
DRAM:  b8050000: 0xc0140180
128 MB
Top of RAM usable for U-Boot at: 88000000
Reserving 228k for U-Boot at: 87fc4000
Reserving 192k for malloc() at: 87f94000
Reserving 56 Bytes for Board Info at: 87f93fc8
Reserving 36 Bytes for Global Data at: 87f93fa4
Reserving 128k for boot params() at: 87f73fa4
Stack Pointer at: 87f73f88
Now running in RAM - U-Boot at: 87fc4000
id read 0x100000ff
flash size 8MB, sector count = 128
Flash:  8 MB
In:    serial
Out:   serial
Err:   serial
Net:   ag7100_enet_initialize...
No valid address in Flash. Using fixed address
: cfg1 0xf cfg2 0x7014
 VSCXXX Found 0  unit 0:0  phy_addr: 1  id: 004dd04e
PHY:   Atheros AR8021
eth0: 00:03:7f:09:0b:ad
eth0 up
eth0
Manu data is valid!
### main_loop entered: bootdelay=4

### main_loop: bootcmd="bootm 0xbf050000"
Enter SPACE to drop into boot loader:  0
## Booting image at bf050000 ...
   Image Name:   MIPS OpenWrt Linux-4.14.275
   Created:      2022-04-20  10:38:55 UTC
   Image Type:   MIPS Linux Kernel Image (gzip compressed)
   Data Size:    2272916 Bytes =  2.2 MB
   Load Address: 80060000
   Entry Point:  80060000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80060000) ...
## Giving linux memsize in bytes, 134217728

Starting kernel ...

[    0.000000] Linux version 4.14.275 (cezary@eko.one.pl) (gcc version 7.5.0 (OpenWrt GCC 7.5.0 r11261-3f5fecfd33)) #0 Wed Apr 20 10:38:55 2022
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
[    0.000000] SoC: Atheros AR7161 rev 2
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] random: get_random_bytes called from 0x804f4740 with crng_init=0
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line:  board=WNDAP360 console=ttyS0,9600 mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,7744k(firmware),64k(nvram)ro,64k(art)ro rootfstype=squashfs noinitrd
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 124292K/131072K available (3969K kernel code, 191K rwdata, 516K rodata, 304K init, 212K bss, 6780K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS: 51
[    0.000000] Clocks: CPU:680.000MHz, DDR:340.000MHz, AHB:170.000MHz, Ref:40.000MHz
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 5621354254 ns
[    0.000008] sched_clock: 32 bits at 340MHz, resolution 2ns, wraps every 6316128254ns
[    0.092818] Calibrating delay loop... 452.19 BogoMIPS (lpj=2260992)
[    0.227861] pid_max: default: 32768 minimum: 301
[    0.283321] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.362469] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.448764] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.566524] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.640446] NET: Registered protocol family 16
[    0.694718] MIPS: machine is NETGEAR WNDAP360
[    1.290610] registering PCI controller with io_map_base unset
[    1.368729] PCI host bridge to bus 0000:00
[    1.417816] pci_bus 0000:00: root bus resource [mem 0x10000000-0x16ffffff]
[    1.500105] pci_bus 0000:00: root bus resource [io  0x0000]
[    1.566830] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    1.648128] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    1.743017] pci 0000:00:11.0: fixup device configuration
[    1.808033] pci 0000:00:11.0: BAR 0: assigned [mem 0x10000000-0x1000ffff]
[    1.891966] clocksource: Switched to clocksource MIPS
[    1.953298] NET: Registered protocol family 2
[    2.005580] IP idents hash table entries: 2048 (order: 2, 16384 bytes)
[    2.084421] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    2.167820] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    2.243875] TCP: Hash tables configured (established 1024 bind 1024)
[    2.320091] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    2.389944] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    2.465122] NET: Registered protocol family 1
[    2.519573] Crashlog allocated RAM at address 0x3f00000
[    2.583117] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[    2.664550] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    2.734378] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    2.858614] io scheduler noop registered
[    2.905619] io scheduler deadline registered (default)
[    2.967444] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    3.045260] console [ttyS0] disabled
[    3.108131] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 10625000) is a 16550A
[    3.212335] console [ttyS0] enabled
[    3.212335] console [ttyS0] enabled
[    3.295766] bootconsole [early0] disabled
[    3.295766] bootconsole [early0] disabled
[    3.396960] m25p80 spi0.0: found mx25l6405d, expected m25p80
[    3.465348] m25p80 spi0.0: mx25l6405d (8192 Kbytes)
[    3.523782] 5 cmdlinepart partitions found on MTD device spi0.0
[    3.594683] Creating 5 MTD partitions on "spi0.0":
[    3.652096] 0x000000000000-0x000000040000 : "u-boot"
[    3.712837] 0x000000040000-0x000000050000 : "u-boot-env"
[    3.778159] 0x000000050000-0x0000007e0000 : "firmware"
[    3.851992] 2 uimage-fw partitions found on MTD device firmware
[    3.922886] 0x000000050000-0x000000280000 : "kernel"
[    3.983005] 0x000000280000-0x0000007e0000 : "rootfs"
[    4.043131] mtd: device 4 (rootfs) set to be root filesystem
[    4.111000] 1 squashfs-split partitions found on MTD device rootfs
[    4.185025] 0x000000690000-0x0000007e0000 : "rootfs_data"
[    4.251860] 0x0000007e0000-0x0000007f0000 : "nvram"
[    4.311411] 0x0000007f0000-0x000000800000 : "art"
[    4.713425] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:01 [uid=004dd04e, driver=Generic PHY]
[    4.823471] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode: rgmii
[    4.898969] NET: Registered protocol family 10
[    4.955660] Segment Routing with IPv6
[    4.999573] NET: Registered protocol family 17
[    5.052850] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    5.208628] 8021q: 802.1Q VLAN Support v1.8
[    5.260058] hctosys: unable to open rtc device (rtc0)
[    5.325472] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[    5.410917] Freeing unused kernel memory: 304K
[    5.464155] This architecture does not have kernel memory protection.
[    6.199528] init: Console is alive
[    6.240506] init: - watchdog -
[    6.451975] random: fast init done
[    7.373047] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    7.504401] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    7.601369] init: - preinit -
[    8.517528] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[    8.605835] random: procd: uninitialized urandom read (4 bytes read)
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    9.602455] eth0: link up (1000Mbps/Full duplex)
[    9.657745] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   11.929498] mount_root: jffs2 not ready yet, using temporary tmpfs overlay
[   12.049975] urandom-seed: Seed file not found (/etc/urandom.seed)
[   12.203794] eth0: link down
[   12.247719] procd: - early -
[   12.282946] procd: - watchdog -
[   12.917703] procd: - watchdog -
[   12.955638] procd: - ubus -
[   13.091672] random: ubusd: uninitialized urandom read (4 bytes read)
[   13.173067] random: ubusd: uninitialized urandom read (4 bytes read)
[   13.249656] random: ubusd: uninitialized urandom read (4 bytes read)
[   13.326631] procd: - init -
Please press Enter to activate this console.
[   14.296231] kmodloader: loading kernel modules from /etc/modules.d/*
[   14.453944] tun: Universal TUN/TAP device driver, 1.6
[   14.588224] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   14.727471] Netfilter messages via NETLINK v0.30.
[   14.799987] urngd: v1.0.2 started.
[   14.842305] ip_set: protocol 6
[   14.968076] Loading modules backported from Linux version v4.19.237-0-ga6e4a1818efa
[   15.059935] Backport generated by backports.git v4.19.237-1-0-gffb89fd9
[   15.258162] random: crng init done
[   15.298917] random: 6 urandom warning(s) missed due to ratelimiting
[   15.376326] ip_tables: (C) 2000-2006 Netfilter Core Team
[   15.460684] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
[   15.795955] wireguard: WireGuard 1.0.20200611 loaded. See [url=http://www.wireguard.com]www.wireguard.com[/url] for information.
[   15.897186] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
[   16.265139] xt_time: kernel timezone is -0000
[   16.567650] PPP generic driver version 2.4.2
[   16.672963] NET: Registered protocol family 24
[   16.833815] pci 0000:00:11.0: using irq 40 for pin 1
[   16.893349] PCI: Enabling device 0000:00:11.0 (0000 -> 0002)
[   16.965955] ath: phy0: Ignoring endianness difference in EEPROM magic bytes.
[   17.068014] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xb0000000, irq=40
[   17.939603] kmodloader: done loading kernel modules from /etc/modules.d/*
[   36.134079] br-lan: port 1(eth0) entered blocking state
[   36.196702] br-lan: port 1(eth0) entered disabled state
[   36.259553] device eth0 entered promiscuous mode
[   36.573316] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   40.322462] eth0: link up (1000Mbps/Full duplex)
[   40.442023] br-lan: port 1(eth0) entered blocking state
[   40.504643] br-lan: port 1(eth0) entered forwarding state
[   40.692029] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   53.217852] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[   53.314644] jffs2_build_filesystem(): unlocking the mtd device...
[   53.314655] done.
[   53.411768] jffs2_build_filesystem(): erasing all blocks after the end marker...
[   62.202534] done.
[   62.315306] jffs2: notice: (1851) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[   62.957189] overlayfs: upper fs does not support tmpfile.
[   91.271743] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready

5 Odpowiedź przez smereka

  • Zarejestrowany: 2014-07-09
  • Posty: 2,443

Odp: netgear wnap320 openwrt?

Na OFW (ustawienia domyślne bez wnikania w żadne opcje) zasuwało max 20Mbit i to nawet na 40MHz a na openwrt zasuwa ponad 100mbit. No rewelacja.

6 Odpowiedź przez smereka (edytowany przez smereka 2023-01-30 13:13:14)

  • Zarejestrowany: 2014-07-09
  • Posty: 2,443

Odp: netgear wnap320 openwrt?

Po niecałym miesiącu działania na CezareOs:

https://i.ibb.co/Wc68Hgy/wnap320-wrt.png


Oczywiście tam w GUI jest, że niby wndap360 bo od tego wgrałem ale fizycznie jest to jak najbardziej wnap320 a firmware od wndap360.

7 Odpowiedź przez artur_n (edytowany przez artur_n 2023-01-31 18:54:00)

  • Zarejestrowany: 2017-05-09
  • Posty: 688

Odp: netgear wnap320 openwrt?

Pozwolę sobie na mały offtop. smereka wrzucaj te tasiemce w znaczniki "code". Strasznie źle się przegląda takie tematy.
Pozdrawiam

GL.iNet GL-MT6000 + 2x AP_Xiaomi AX3000T

8 Odpowiedź przez smereka

  • Zarejestrowany: 2014-07-09
  • Posty: 2,443

Odp: netgear wnap320 openwrt?

Napisz co konkretnie mam zrobić i zastosuje.Najlepiej instrukcja krok po kroku i z przykladem

9 Odpowiedź przez lexmark3200

  • Zarejestrowany: 2021-11-19
  • Posty: 1,011

Odp: netgear wnap320 openwrt?

Macie log w grania:

U-Boot 1.1.4 dni-1.09 (Jul  1 2010 - 11:39:24)

AP94 (ar7100) U-boot 0.0.12
DRAM:  b8050000: 0xc0140180
128 MB
Top of RAM usable for U-Boot at: 88000000
Reserving 228k for U-Boot at: 87fc4000
Reserving 192k for malloc() at: 87f94000
Reserving 56 Bytes for Board Info at: 87f93fc8
Reserving 36 Bytes for Global Data at: 87f93fa4
Reserving 128k for boot params() at: 87f73fa4
Stack Pointer at: 87f73f88
Now running in RAM - U-Boot at: 87fc4000
id read 0x100000ff
flash size 8MB, sector count = 128
Flash:  8 MB
In:    serial
Out:   serial
Err:   serial
Net:   ag7100_enet_initialize...
No valid address in Flash. Using fixed address
: cfg1 0xf cfg2 0x7014
VSCXXX Found 0  unit 0:0  phy_addr: 1  id: 004dd04e
PHY:   Atheros AR8021
eth0: 00:03:7f:09:0b:ad
eth0 up
eth0
Manu data is valid!
### main_loop entered: bootdelay=4

### main_loop: bootcmd="bootm 0xbf050000"
Enter SPACE to drop into boot loader:  0
ar7100> setenv ipaddr 192.168.1.1
ar7100> setenv serverip 192.168.1.42
ar7100> saveenv
Saving Environment to Flash...
Protect off BF040000 ... BF04FFFF
Un-Protecting sectors 4..4 in bank 1
Un-Protected 1 sectors
Erasing Flash...Erase Flash from 0xbf040000 to 0xbf04ffff in Bank # 1
First 0x4 last 0x4 sector size 0x10000                                                                                                                                                                                                      4
Erased 1 sectors
Writing to Flash... write addr: bf040000
done
Protecting sectors 4..4 in bank 1
Protected 1 sectors
ar7100> reset

Resetting...

U-Boot 1.1.4 dni-1.09 (Jul  1 2010 - 11:39:24)

AP94 (ar7100) U-boot 0.0.12
DRAM:  b8050000: 0xc0140180
128 MB
Top of RAM usable for U-Boot at: 88000000
Reserving 228k for U-Boot at: 87fc4000
Reserving 192k for malloc() at: 87f94000
Reserving 56 Bytes for Board Info at: 87f93fc8
Reserving 36 Bytes for Global Data at: 87f93fa4
Reserving 128k for boot params() at: 87f73fa4
Stack Pointer at: 87f73f88
Now running in RAM - U-Boot at: 87fc4000
id read 0x100000ff
flash size 8MB, sector count = 128
Flash:  8 MB
In:    serial
Out:   serial
Err:   serial
Net:   ag7100_enet_initialize...
No valid address in Flash. Using fixed address
: cfg1 0xf cfg2 0x7014
VSCXXX Found 0  unit 0:0  phy_addr: 1  id: 004dd04e
PHY:   Atheros AR8021
eth0: 00:03:7f:09:0b:ad
eth0 up
eth0
Manu data is valid!
### main_loop entered: bootdelay=4

### main_loop: bootcmd="bootm 0xbf050000"
Enter SPACE to drop into boot loader:  0
ar7100> tftpboot 0x81000000 1.bin
Trying eth0
Using eth0 device
TFTP from server 192.168.1.42; our IP address is 192.168.1.1
Filename '1.bin'.
Load address: 0x81000000
Loading: #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         ###############################################
done
Bytes transferred = 4233506 (409922 hex)
ar7100> bootm 0x81000000
## Booting image at 81000000 ...
   Image Name:   MIPS OpenWrt Linux-4.14.275
   Created:      2022-04-20  10:38:55 UTC
   Image Type:   MIPS Linux Kernel Image (gzip compressed)
   Data Size:    4233442 Bytes =  4 MB
   Load Address: 80060000
   Entry Point:  80060000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80060000) ...
## Giving linux memsize in bytes, 134217728

Starting kernel ...

[    0.000000] Linux version 4.14.275 (cezary@eko.one.pl) (gcc version 7.5.0 (OpenWrt GCC 7.5.0 r11261-3f5fecfd33)) #0 Wed Apr 20 10:38:55 2022
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
[    0.000000] SoC: Atheros AR7161 rev 2
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] random: get_random_bytes called from 0x804f4740 with crng_init=0
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line:  board=WNDAP360 console=ttyS0,9600 mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,7744k(firmware),64k(nvram)ro,64k(art)ro rootfstype=squashfs noinitrd
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 122372K/131072K available (3969K kernel code, 191K rwdata, 516K rodata, 2224K init, 212K bss, 8700K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS: 51
[    0.000000] Clocks: CPU:680.000MHz, DDR:340.000MHz, AHB:170.000MHz, Ref:40.000MHz
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 5621354254 ns
[    0.000008] sched_clock: 32 bits at 340MHz, resolution 2ns, wraps every 6316128254ns
[    0.092819] Calibrating delay loop... 452.19 BogoMIPS (lpj=2260992)
[    0.227861] pid_max: default: 32768 minimum: 301
[    0.283321] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.362469] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.448764] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.566523] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.640446] NET: Registered protocol family 16
[    0.694716] MIPS: machine is NETGEAR WNDAP360
[    1.290610] registering PCI controller with io_map_base unset
[    1.368725] PCI host bridge to bus 0000:00
[    1.417816] pci_bus 0000:00: root bus resource [mem 0x10000000-0x16ffffff]
[    1.500105] pci_bus 0000:00: root bus resource [io  0x0000]
[    1.566830] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    1.648128] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    1.743016] pci 0000:00:11.0: fixup device configuration
[    1.808033] pci 0000:00:11.0: BAR 0: assigned [mem 0x10000000-0x1000ffff]
[    1.891967] clocksource: Switched to clocksource MIPS
[    1.953298] NET: Registered protocol family 2
[    2.005581] IP idents hash table entries: 2048 (order: 2, 16384 bytes)
[    2.084419] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    2.167820] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    2.243875] TCP: Hash tables configured (established 1024 bind 1024)
[    2.320091] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    2.389944] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    2.465122] NET: Registered protocol family 1
[    4.211976] random: fast init done
[    5.372597] Crashlog allocated RAM at address 0x3f00000
[    5.436297] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[    5.517691] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    5.587495] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    5.766463] io scheduler noop registered
[    5.813387] io scheduler deadline registered (default)
[    5.875204] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    5.953102] console [ttyS0] disabled
[    6.015894] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 10625000) is a 16550A
[    6.120110] console [ttyS0] enabled
[    6.120110] console [ttyS0] enabled
[    6.203544] bootconsole [early0] disabled
[    6.203544] bootconsole [early0] disabled
[    6.304790] m25p80 spi0.0: found mx25l6405d, expected m25p80
[    6.373235] m25p80 spi0.0: mx25l6405d (8192 Kbytes)
[    6.431660] 5 cmdlinepart partitions found on MTD device spi0.0
[    6.502562] Creating 5 MTD partitions on "spi0.0":
[    6.559976] 0x000000000000-0x000000040000 : "u-boot"
[    6.638986] 0x000000040000-0x000000050000 : "u-boot-env"
[    6.722096] 0x000000050000-0x0000007e0000 : "firmware"
[    6.797342] 2 uimage-fw partitions found on MTD device firmware
[    6.868296] 0x000000050000-0x000000760000 : "kernel"
[    6.928388] 0x000000760000-0x0000007e0000 : "rootfs"
[    6.988516] mtd: device 4 (rootfs) set to be root filesystem
[    7.056382] mtdsplit: no squashfs found in "rootfs"
[    7.134098] 0x0000007e0000-0x0000007f0000 : "nvram"
[    7.212033] 0x0000007f0000-0x000000800000 : "art"
[    7.653425] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:01 [uid=004dd04e, driver=Generic PHY]
[    7.763441] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode: rgmii
[    7.838951] NET: Registered protocol family 10
[    7.895724] Segment Routing with IPv6
[    7.939647] NET: Registered protocol family 17
[    7.992928] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    8.148699] 8021q: 802.1Q VLAN Support v1.8
[    8.200120] hctosys: unable to open rtc device (rtc0)
[    8.267475] Freeing unused kernel memory: 2224K
[    8.321704] This architecture does not have kernel memory protection.
[    8.411801] init: Console is alive
[    8.452887] init: - watchdog -
[    8.508148] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    8.591284] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    8.688246] init: - preinit -
[    8.876042] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[    8.964791] random: procd: uninitialized urandom read (4 bytes read)
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[   12.159906] procd: - early -
[   12.195099] procd: - watchdog -
[   12.796387] procd: - watchdog -
[   12.834336] procd: - ubus -
[   12.873755] random: ubusd: uninitialized urandom read (4 bytes read)
[   12.950928] random: ubusd: uninitialized urandom read (4 bytes read)
[   13.027518] random: ubusd: uninitialized urandom read (4 bytes read)
[   13.104525] procd: - init -
Please press Enter to activate this console.
[   13.523664] kmodloader: loading kernel modules from /etc/modules.d/*
[   13.686837] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   13.828123] Loading modules backported from Linux version v4.19.237-0-ga6e4a1818efa
[   13.919996] Backport generated by backports.git v4.19.237-1-0-gffb89fd9
[   14.087132] urngd: v1.0.2 started.
[   14.173854] ip_tables: (C) 2000-2006 Netfilter Core Team
[   14.308237] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
[   14.442017] random: crng init done
[   14.482781] random: 6 urandom warning(s) missed due to ratelimiting
[   14.605980] xt_time: kernel timezone is -0000
[   14.726245] PPP generic driver version 2.4.2
[   14.832654] NET: Registered protocol family 24
[   14.982937] pci 0000:00:11.0: using irq 40 for pin 1
[   15.042430] PCI: Enabling device 0000:00:11.0 (0000 -> 0002)
[   15.115034] ath: phy0: Ignoring endianness difference in EEPROM magic bytes.
[   15.217107] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xb0000000, irq=40
[   15.862307] kmodloader: done loading kernel modules from /etc/modules.d/*
[   26.205580] eth0: link up (1000Mbps/Full duplex)
[   26.272324] br-lan: port 1(eth0) entered blocking state
[   26.334942] br-lan: port 1(eth0) entered disabled state
[   26.397806] device eth0 entered promiscuous mode
[   26.523641] br-lan: port 1(eth0) entered blocking state
[   26.586245] br-lan: port 1(eth0) entered forwarding state
[   26.651092] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   27.282085] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   91.042108] eth0: link down
[   91.076092] br-lan: port 1(eth0) entered disabled state
[  183.602455] eth0: link up (1000Mbps/Full duplex)
[  183.658065] br-lan: port 1(eth0) entered blocking state
[  183.720635] br-lan: port 1(eth0) entered forwarding state



BusyBox v1.30.1 () built-in shell (ash)

  _______                     ________        __
|       |.-----.-----.-----.|  |  |  |.----.|  |_
|   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
|_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
-----------------------------------------------------------------------------
|                                                                           |
| OpenWrt 19.07-SNAPSHOT, r11430-ecbbb373ed                                 |
|                                                                           |
| Build time: 2022-05-13 22:57 CEST                                         |
| Cezary Jackiewicz, [url]https://eko.one.pl[/url]                                     |
|                                                                           |
-----------------------------------------------------------------------------
| Machine: NETGEAR WNDAP360                                                 |
| Uptime: 0d, 00:04:48                                                      |
| Load: 0.04 0.07 0.03                                                      |
| Flash:                                                                    |
| Memory: total: 121.7MB, free: 113.0MB, used: 7%                           |
| Leases: 1                                                                 |
| lan: static, 192.168.1.1                                                  |
-----------------------------------------------------------------------------
=== WARNING! ================================================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.
-----------------------------------------------------------------------------
root@OpenWrt:/# sysupgrade -n /tmp/1.bin
Image metadata not found
Commencing upgrade. Closing all shell sessions.
Watchdog handover: fd=3
- watchdog -
killall: telnetd: no process kilSending TERM to remaining processes ... ntpd dnsmasq ubusd urngd logd netifd odhcpd
Sending KILL to remaining processes ...
Performing system upgrade...
Unlocking firmware ...

Writing from <stdin> to firmware ...
Upgrade completed
Rebooting system[  370.980984] reboot: Restarting system


U-Boot 1.1.4 dni-1.09 (Jul  1 2010 - 11:39:24)

AP94 (ar7100) U-boot 0.0.12
DRAM:  b8050000: 0xc0140180
128 MB
Top of RAM usable for U-Boot at: 88000000
Reserving 228k for U-Boot at: 87fc4000
Reserving 192k for malloc() at: 87f94000
Reserving 56 Bytes for Board Info at: 87f93fc8
Reserving 36 Bytes for Global Data at: 87f93fa4
Reserving 128k for boot params() at: 87f73fa4
Stack Pointer at: 87f73f88
Now running in RAM - U-Boot at: 87fc4000
id read 0x100000ff
flash size 8MB, sector count = 128
Flash:  8 MB
In:    serial
Out:   serial
Err:   serial
Net:   ag7100_enet_initialize...
No valid address in Flash. Using fixed address
: cfg1 0xf cfg2 0x7014
VSCXXX Found 0  unit 0:0  phy_addr: 1  id: 004dd04e
PHY:   Atheros AR8021
eth0: 00:03:7f:09:0b:ad
eth0 up
eth0
Manu data is valid!
### main_loop entered: bootdelay=4

### main_loop: bootcmd="bootm 0xbf050000"
Enter SPACE to drop into boot loader:  0
## Booting image at bf050000 ...
   Image Name:   MIPS OpenWrt Linux-4.14.275
   Created:      2022-04-20  10:38:55 UTC
   Image Type:   MIPS Linux Kernel Image (gzip compressed)
   Data Size:    2272916 Bytes =  2.2 MB
   Load Address: 80060000
   Entry Point:  80060000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80060000) ...
## Giving linux memsize in bytes, 134217728

Starting kernel ...

[    0.000000] Linux version 4.14.275 (cezary@eko.one.pl) (gcc version 7.5.0 (OpenWrt GCC 7.5.0 r11261-3f5fecfd33)) #0 Wed Apr 20 10:38:55 2022
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
[    0.000000] SoC: Atheros AR7161 rev 2
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] random: get_random_bytes called from 0x804f4740 with crng_init=0
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line:  board=WNDAP360 console=ttyS0,9600 mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,7744k(firmware),64k(nvram)ro,64k(art)ro rootfstype=squashfs noinitrd
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 124292K/131072K available (3969K kernel code, 191K rwdata, 516K rodata, 304K init, 212K bss, 6780K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS: 51
[    0.000000] Clocks: CPU:680.000MHz, DDR:340.000MHz, AHB:170.000MHz, Ref:40.000MHz
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 5621354254 ns
[    0.000008] sched_clock: 32 bits at 340MHz, resolution 2ns, wraps every 6316128254ns
[    0.092818] Calibrating delay loop... 452.19 BogoMIPS (lpj=2260992)
[    0.227861] pid_max: default: 32768 minimum: 301
[    0.283321] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.362469] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.448764] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.566524] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.640446] NET: Registered protocol family 16
[    0.694718] MIPS: machine is NETGEAR WNDAP360
[    1.290610] registering PCI controller with io_map_base unset
[    1.368729] PCI host bridge to bus 0000:00
[    1.417816] pci_bus 0000:00: root bus resource [mem 0x10000000-0x16ffffff]
[    1.500105] pci_bus 0000:00: root bus resource [io  0x0000]
[    1.566830] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    1.648128] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    1.743017] pci 0000:00:11.0: fixup device configuration
[    1.808033] pci 0000:00:11.0: BAR 0: assigned [mem 0x10000000-0x1000ffff]
[    1.891966] clocksource: Switched to clocksource MIPS
[    1.953298] NET: Registered protocol family 2
[    2.005580] IP idents hash table entries: 2048 (order: 2, 16384 bytes)
[    2.084421] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    2.167820] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    2.243875] TCP: Hash tables configured (established 1024 bind 1024)
[    2.320091] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    2.389944] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    2.465122] NET: Registered protocol family 1
[    2.519573] Crashlog allocated RAM at address 0x3f00000
[    2.583117] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[    2.664550] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    2.734378] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    2.858614] io scheduler noop registered
[    2.905619] io scheduler deadline registered (default)
[    2.967444] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    3.045260] console [ttyS0] disabled
[    3.108131] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 10625000) is a 16550A
[    3.212335] console [ttyS0] enabled
[    3.212335] console [ttyS0] enabled
[    3.295766] bootconsole [early0] disabled
[    3.295766] bootconsole [early0] disabled
[    3.396960] m25p80 spi0.0: found mx25l6405d, expected m25p80
[    3.465348] m25p80 spi0.0: mx25l6405d (8192 Kbytes)
[    3.523782] 5 cmdlinepart partitions found on MTD device spi0.0
[    3.594683] Creating 5 MTD partitions on "spi0.0":
[    3.652096] 0x000000000000-0x000000040000 : "u-boot"
[    3.712837] 0x000000040000-0x000000050000 : "u-boot-env"
[    3.778159] 0x000000050000-0x0000007e0000 : "firmware"
[    3.851992] 2 uimage-fw partitions found on MTD device firmware
[    3.922886] 0x000000050000-0x000000280000 : "kernel"
[    3.983005] 0x000000280000-0x0000007e0000 : "rootfs"
[    4.043131] mtd: device 4 (rootfs) set to be root filesystem
[    4.111000] 1 squashfs-split partitions found on MTD device rootfs
[    4.185025] 0x000000690000-0x0000007e0000 : "rootfs_data"
[    4.251860] 0x0000007e0000-0x0000007f0000 : "nvram"
[    4.311411] 0x0000007f0000-0x000000800000 : "art"
[    4.713425] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:01 [uid=004dd04e, driver=Generic PHY]
[    4.823471] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode: rgmii
[    4.898969] NET: Registered protocol family 10
[    4.955660] Segment Routing with IPv6
[    4.999573] NET: Registered protocol family 17
[    5.052850] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    5.208628] 8021q: 802.1Q VLAN Support v1.8
[    5.260058] hctosys: unable to open rtc device (rtc0)
[    5.325472] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[    5.410917] Freeing unused kernel memory: 304K
[    5.464155] This architecture does not have kernel memory protection.
[    6.199528] init: Console is alive
[    6.240506] init: - watchdog -
[    6.451975] random: fast init done
[    7.373047] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    7.504401] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    7.601369] init: - preinit -
[    8.517528] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[    8.605835] random: procd: uninitialized urandom read (4 bytes read)
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    9.602455] eth0: link up (1000Mbps/Full duplex)
[    9.657745] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   11.929498] mount_root: jffs2 not ready yet, using temporary tmpfs overlay
[   12.049975] urandom-seed: Seed file not found (/etc/urandom.seed)
[   12.203794] eth0: link down
[   12.247719] procd: - early -
[   12.282946] procd: - watchdog -
[   12.917703] procd: - watchdog -
[   12.955638] procd: - ubus -
[   13.091672] random: ubusd: uninitialized urandom read (4 bytes read)
[   13.173067] random: ubusd: uninitialized urandom read (4 bytes read)
[   13.249656] random: ubusd: uninitialized urandom read (4 bytes read)
[   13.326631] procd: - init -
Please press Enter to activate this console.
[   14.296231] kmodloader: loading kernel modules from /etc/modules.d/*
[   14.453944] tun: Universal TUN/TAP device driver, 1.6
[   14.588224] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   14.727471] Netfilter messages via NETLINK v0.30.
[   14.799987] urngd: v1.0.2 started.
[   14.842305] ip_set: protocol 6
[   14.968076] Loading modules backported from Linux version v4.19.237-0-ga6e4a1818efa
[   15.059935] Backport generated by backports.git v4.19.237-1-0-gffb89fd9
[   15.258162] random: crng init done
[   15.298917] random: 6 urandom warning(s) missed due to ratelimiting
[   15.376326] ip_tables: (C) 2000-2006 Netfilter Core Team
[   15.460684] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
[   15.795955] wireguard: WireGuard 1.0.20200611 loaded. See [url=http://www.wireguard.com]www.wireguard.com[/url] for information.
[   15.897186] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
[   16.265139] xt_time: kernel timezone is -0000
[   16.567650] PPP generic driver version 2.4.2
[   16.672963] NET: Registered protocol family 24
[   16.833815] pci 0000:00:11.0: using irq 40 for pin 1
[   16.893349] PCI: Enabling device 0000:00:11.0 (0000 -> 0002)
[   16.965955] ath: phy0: Ignoring endianness difference in EEPROM magic bytes.
[   17.068014] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xb0000000, irq=40
[   17.939603] kmodloader: done loading kernel modules from /etc/modules.d/*
[   36.134079] br-lan: port 1(eth0) entered blocking state
[   36.196702] br-lan: port 1(eth0) entered disabled state
[   36.259553] device eth0 entered promiscuous mode
[   36.573316] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   40.322462] eth0: link up (1000Mbps/Full duplex)
[   40.442023] br-lan: port 1(eth0) entered blocking state
[   40.504643] br-lan: port 1(eth0) entered forwarding state
[   40.692029] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   53.217852] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[   53.314644] jffs2_build_filesystem(): unlocking the mtd device...
[   53.314655] done.
[   53.411768] jffs2_build_filesystem(): erasing all blocks after the end marker...
[   62.202534] done.
[   62.315306] jffs2: notice: (1851) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[   62.957189] overlayfs: upper fs does not support tmpfile.
[   91.271743] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready

Tak wygląda twój post po edycji.
Dajesz w [cod*] Twój kod (log czy co tam masz... [/cod*] oczywiście gdzie * wstaw e ;-)

10 Odpowiedź przez smereka

  • Zarejestrowany: 2014-07-09
  • Posty: 2,443

Odp: netgear wnap320 openwrt?

Dziękuję za instrukcję. Poprawiłem. Rzeczywiście minimalnie lepiej to wygląda wink

11 Odpowiedź przez lexmark3200

  • Zarejestrowany: 2021-11-19
  • Posty: 1,011

Odp: netgear wnap320 openwrt?

Spoko, cieszę się że mogę w jakiś sposób pomóc.

Pozdrawiam