FAQ o OpenWrt | Sprzedam różne routery | Oddam

Focus · 2022-11-20 14:49:16

Focus
Użytkownik
Nieaktywny

Zarejestrowany: 2020-10-20
Posty: 973

Temat: Karta Wi Fi przez USB automatyczne uruchamianie

Mam router działający jako AP, który łączy się przez STA z innym routerem.
Aby dostać się do tego AP bez kabli używam karty Wi Fi na USB.

Pytanie: jak zrobić aby ta karta Wi Fi USB uruchamiała się automatycznie po włożeniu jej do USB?

Wertuję internet i czytam forum ale wszystko co znajduję to dotyczy modemów USB lub dysków.

Podpowie mi ktoś jak do tego podejść?
Mogą być linki lub informacje czego mam szukać?

W tym AP jest LEDE Reboot 17.01-SNAPSHOT r3925-79c8f2f50b

Cezary · 2022-11-20 14:52:21

Cezary
...
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2006-02-25
Posty: 116,956

Odp: Karta Wi Fi przez USB automatyczne uruchamianie

W sumie nic nie musisz zrobić. Karta w usb, ładują się sterowniki, system widzi kartę i uruchamia wifi. Od zawsze w sumie.
Wyjmujesz kartę, wkładasz kartę, wifi się uruchamia.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Focus · 2022-11-20 14:58:44

Focus
Użytkownik
Nieaktywny

Zarejestrowany: 2020-10-20
Posty: 973

Odp: Karta Wi Fi przez USB automatyczne uruchamianie

Ogólnie po włożeniu do USB karta Wi Fi działa, ale nie uruchamia się samo Wi Fi.
Po wydaniu polecenia wifi w putty (przez kabel) Wi Fi od razu wstaje.

Cezary · 2022-11-20 15:07:19

Cezary
...
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2006-02-25
Posty: 116,956

Odp: Karta Wi Fi przez USB automatyczne uruchamianie

Zrób logread po czymś takim i pokaż co system wypisuje.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Focus · 2022-11-20 15:46:04

Focus
Użytkownik
Nieaktywny

Zarejestrowany: 2020-10-20
Posty: 973

Odp: Karta Wi Fi przez USB automatyczne uruchamianie

Wklejam loga od momentu wyjęcia i włożenia karty wifi usb.

Sun Nov 20 14:33:42 2022 kern.info kernel: [ 156.983792] usb 1-1: USB disconnect, device number 2
Sun Nov 20 14:33:42 2022 kern.err kernel: [ 157.097125] ath: phy1: RX failed to go idle in 10 ms RXSM=0x2000000
Sun Nov 20 14:33:42 2022 kern.err kernel: [ 157.208793] ath: phy1: RX failed to go idle in 10 ms RXSM=0x2000000
Sun Nov 20 14:33:42 2022 kern.err kernel: [ 157.318508] ath: phy1: RX failed to go idle in 10 ms RXSM=0x2000000
Sun Nov 20 14:33:42 2022 kern.err kernel: [ 157.428780] ath: phy1: RX failed to go idle in 10 ms RXSM=0x2000000
Sun Nov 20 14:33:42 2022 kern.info kernel: [ 157.435772] br-lan: port 2(wlan1) entered disabled state
Sun Nov 20 14:33:42 2022 daemon.notice netifd: Network device 'wlan1' link is down
Sun Nov 20 14:33:42 2022 daemon.notice hostapd: wlan1: INTERFACE-DISABLED
Sun Nov 20 14:33:42 2022 kern.info kernel: [ 157.449962] device wlan1 left promiscuous mode
Sun Nov 20 14:33:42 2022 kern.info kernel: [ 157.454646] br-lan: port 2(wlan1) entered disabled state
Sun Nov 20 14:33:42 2022 kern.info kernel: [ 157.466054] usb 1-1: ath9k_htc: USB layer deinitialized
Sun Nov 20 14:33:43 2022 kern.info kernel: [ 158.814526] usb 1-1: new high-speed USB device number 3 using ehci-platform
Sun Nov 20 14:33:43 2022 kern.info kernel: [ 158.991834] usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested
Sun Nov 20 14:33:44 2022 kern.info kernel: [ 159.293872] usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008
Sun Nov 20 14:33:44 2022 kern.info kernel: [ 159.544853] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits
Sun Nov 20 14:33:44 2022 kern.info kernel: [ 159.811576] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.4
Sun Nov 20 14:33:44 2022 kern.info kernel: [ 159.817384] ath9k_htc 1-1:1.0: FW RMW support: On
Sun Nov 20 14:33:44 2022 kern.debug kernel: [ 159.822250] ath: EEPROM regdomain: 0x809c
Sun Nov 20 14:33:44 2022 kern.debug kernel: [ 159.822262] ath: EEPROM indicates we should expect a country code
Sun Nov 20 14:33:44 2022 kern.debug kernel: [ 159.822277] ath: doing EEPROM country->regdmn map search
Sun Nov 20 14:33:44 2022 kern.debug kernel: [ 159.822289] ath: country maps to regdmn code: 0x52
Sun Nov 20 14:33:44 2022 kern.debug kernel: [ 159.822303] ath: Country alpha2 being used: CN
Sun Nov 20 14:33:44 2022 kern.debug kernel: [ 159.822315] ath: Regpair used: 0x52
Sun Nov 20 14:33:44 2022 kern.info kernel: [ 159.830533] ieee80211 phy2: Atheros AR9271 Rev:1
Sun Nov 20 14:33:44 2022 kern.info kernel: [ 160.017220] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
Sun Nov 20 14:33:44 2022 daemon.notice hostapd: wlan1: INTERFACE-ENABLED
Sun Nov 20 14:33:44 2022 daemon.err hostapd: Failed to set beacon parameters

Cezary · 2022-11-20 15:59:05

Cezary
...
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2006-02-25
Posty: 116,956

Odp: Karta Wi Fi przez USB automatyczne uruchamianie

Trochę dalej jeszcze. Wykrył kartę, chcę uruchamiać, napisał że jednego parametru nie ustai. Ale dalej pokaż.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Focus · 2022-11-20 16:59:01

Focus
Użytkownik
Nieaktywny

Zarejestrowany: 2020-10-20
Posty: 973

Odp: Karta Wi Fi przez USB automatyczne uruchamianie

To już jest koniec loga. Dalej nic nie ma.

edit.

Wklejam 2 logi w całości.
1. z włożoną kartą wifi usb (działa połączenie wifi)
2. kiedy wkładam z powrotem kartę wifi usb (nie działa połączenie wifi)

| radio0: mode: ap, ssid: Wi-Fi, channel: 11, conn: 0 |
| radio1: mode: ap, ssid: Borys, channel: 8, conn: 0 |
| radio0: mode: sta, ssid: Wi-Fi, channel: 11, conn: 1 |
-----------------------------------------------------------------------------
root@Router:~# logread
Sun Nov 20 16:11:42 2022 kern.notice kernel: [ 0.000000] Linux version 4.4.140 (cezary@eko.one.pl) (gcc version 5.4.0 (LEDE GCC 5.4.0 r3785-ceea0ac) ) #0 Tue Jul 17 05:17:48 2018
Sun Nov 20 16:11:42 2022 kern.debug kernel: [ 0.000000] MyLoader: sysp=e72c40a6, boardp=3050a00a, parts=15d661ab
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.000000] bootconsole [early0] enabled
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.000000] CPU0 revision is: 0001974c (MIPS 74Kc)
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.000000] SoC: Atheros AR9341 rev 3
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.000000] Determined physical RAM map:
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.000000] memory: 02000000 @ 00000000 (usable)
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.000000] Initrd not found or empty - disabling initrd
Sun Nov 20 16:11:42 2022 kern.warn kernel: [ 0.000000] No valid device tree found, continuing without
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.000000] Zone ranges:
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000001ffffff]
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.000000] Movable zone start for each node
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.000000] Early memory node ranges
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000001ffffff]
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000001ffffff]
Sun Nov 20 16:11:42 2022 kern.debug kernel: [ 0.000000] On node 0 totalpages: 8192
Sun Nov 20 16:11:42 2022 kern.debug kernel: [ 0.000000] free_area_init_node: node 0, pgdat 8043a4b0, node_mem_map 81000000
Sun Nov 20 16:11:42 2022 kern.debug kernel: [ 0.000000] Normal zone: 64 pages used for memmap
Sun Nov 20 16:11:42 2022 kern.debug kernel: [ 0.000000] Normal zone: 0 pages reserved
Sun Nov 20 16:11:42 2022 kern.debug kernel: [ 0.000000] Normal zone: 8192 pages, LIFO batch:0
Sun Nov 20 16:11:42 2022 kern.warn kernel: [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Sun Nov 20 16:11:42 2022 kern.warn kernel: [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Sun Nov 20 16:11:42 2022 kern.debug kernel: [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
Sun Nov 20 16:11:42 2022 kern.debug kernel: [ 0.000000] pcpu-alloc: [0] 0
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
Sun Nov 20 16:11:42 2022 kern.notice kernel: [ 0.000000] Kernel command line: board=TL-MR3420-v2 console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.000000] Writing ErrCtl register=00000000
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.000000] Readback ErrCtl register=00000000
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.000000] Memory: 27416K/32768K available (3130K kernel code, 162K rwdata, 780K rodata, 336K init, 205K bss, 5352K reserved, 0K cma-reserved)
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.000000] NR_IRQS:51
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.000000] Clocks: CPU:535.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7144898866 ns
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.000011] sched_clock: 32 bits at 267MHz, resolution 3ns, wraps every 8027976190ns
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.008234] Calibrating delay loop... 266.64 BogoMIPS (lpj=1333248)
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.091044] pid_max: default: 32768 minimum: 301
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.096053] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.103039] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.113530] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.123958] futex hash table entries: 256 (order: -1, 3072 bytes)
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.131822] NET: Registered protocol family 16
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.138310] MIPS: machine is TP-LINK TL-MR3420 v2
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.595449] clocksource: Switched to clocksource MIPS
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.602385] NET: Registered protocol family 2
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.608061] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.615423] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.622192] TCP: Hash tables configured (established 1024 bind 1024)
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.629002] UDP hash table entries: 256 (order: 0, 4096 bytes)
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.635179] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.642180] NET: Registered protocol family 1
Sun Nov 20 16:11:42 2022 kern.debug kernel: [ 0.646911] PCI: CLS 0 bytes, default 32
Sun Nov 20 16:11:42 2022 kern.warn kernel: [ 0.652331] Crashlog allocated RAM at address 0x1f00000
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.675560] squashfs: version 4.0 (2009/01/31) Phillip Lougher
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.681732] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.695106] io scheduler noop registered
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.699316] io scheduler deadline registered (default)
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.705039] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.714901] console [ttyS0] disabled
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.738809] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 1562500) is a 16550A
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.747916] console [ttyS0] enabled
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.755477] bootconsole [early0] disabled
Sun Nov 20 16:11:42 2022 kern.warn kernel: [ 0.770199] m25p80 spi0.0: found en25q32b, expected m25p80
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.775953] m25p80 spi0.0: en25q32b (4096 Kbytes)
Sun Nov 20 16:11:42 2022 kern.notice kernel: [ 0.782145] 5 tp-link partitions found on MTD device spi0.0
Sun Nov 20 16:11:42 2022 kern.notice kernel: [ 0.787964] Creating 5 MTD partitions on "spi0.0":
Sun Nov 20 16:11:42 2022 kern.notice kernel: [ 0.792920] 0x000000000000-0x000000020000 : "u-boot"
Sun Nov 20 16:11:42 2022 kern.notice kernel: [ 0.799738] 0x000000020000-0x00000016ef94 : "kernel"
Sun Nov 20 16:11:42 2022 kern.notice kernel: [ 0.806813] 0x00000016ef94-0x0000003f0000 : "rootfs"
Sun Nov 20 16:11:42 2022 kern.notice kernel: [ 0.813803] mtd: device 2 (rootfs) set to be root filesystem
Sun Nov 20 16:11:42 2022 kern.notice kernel: [ 0.819768] 1 squashfs-split partitions found on MTD device rootfs
Sun Nov 20 16:11:42 2022 kern.notice kernel: [ 0.826178] 0x000000380000-0x0000003f0000 : "rootfs_data"
Sun Nov 20 16:11:42 2022 kern.notice kernel: [ 0.833671] 0x0000003f0000-0x000000400000 : "art"
Sun Nov 20 16:11:42 2022 kern.notice kernel: [ 0.840550] 0x000000020000-0x0000003f0000 : "firmware"
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.865929] libphy: ag71xx_mdio: probed
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 1.457546] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:00 [uid=004dd042, driver=Generic PHY]
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 1.467806] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 2.057331] ag71xx-mdio.1: Found an AR934X built-in switch
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 2.099689] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 2.109082] NET: Registered protocol family 10
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 2.119302] NET: Registered protocol family 17
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 2.123987] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 2.137212] 8021q: 802.1Q VLAN Support v1.8
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 2.143623] hctosys: unable to open rtc device (rtc0)
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 2.153931] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 2.163455] Freeing unused kernel memory: 336K
Sun Nov 20 16:11:42 2022 user.info kernel: [ 3.284967] init: Console is alive
Sun Nov 20 16:11:42 2022 user.info kernel: [ 3.288818] init: - watchdog -
Sun Nov 20 16:11:42 2022 user.info kernel: [ 4.471208] kmodloader: loading kernel modules from /etc/modules-boot.d/*
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 4.546821] usbcore: registered new interface driver usbfs
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 4.552606] usbcore: registered new interface driver hub
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 4.558289] usbcore: registered new device driver usb
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 4.570036] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 4.578722] ehci-platform: EHCI generic platform driver
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 4.584234] ehci-platform ehci-platform: EHCI Host Controller
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 4.590281] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 4.600592] ehci-platform ehci-platform: TX-TX IDP fix enabled
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 4.606662] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 4.625494] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 4.632985] hub 1-0:1.0: USB hub found
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 4.637399] hub 1-0:1.0: 1 port detected
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 4.644964] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 4.653171] ohci-platform: OHCI generic platform driver
Sun Nov 20 16:11:42 2022 user.info kernel: [ 4.659528] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
Sun Nov 20 16:11:42 2022 user.info kernel: [ 4.677537] init: - preinit -
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 5.135787] usb 1-1: new high-speed USB device number 2 using ehci-platform
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 5.240580] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
Sun Nov 20 16:11:42 2022 kern.notice kernel: [ 5.270480] random: procd: uninitialized urandom read (4 bytes read, 8 bits of entropy available)
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 6.836718] eth1: link up (1000Mbps/Full duplex)
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 6.841531] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
Sun Nov 20 16:11:42 2022 kern.notice kernel: [ 7.591870] jffs2: notice: (399) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
Sun Nov 20 16:11:42 2022 user.info kernel: [ 7.610104] mount_root: switching to jffs2 overlay
Sun Nov 20 16:11:42 2022 user.warn kernel: [ 7.624598] urandom-seed: Seeding with /etc/urandom.seed
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 7.833111] eth1: link down
Sun Nov 20 16:11:42 2022 user.info kernel: [ 7.849961] procd: - early -
Sun Nov 20 16:11:42 2022 user.info kernel: [ 7.853063] procd: - watchdog -
Sun Nov 20 16:11:42 2022 kern.notice kernel: [ 8.422089] random: jshn: uninitialized urandom read (4 bytes read, 14 bits of entropy available)
Sun Nov 20 16:11:42 2022 user.info kernel: [ 8.607117] procd: - watchdog -
Sun Nov 20 16:11:42 2022 user.info kernel: [ 8.610703] procd: - ubus -
Sun Nov 20 16:11:42 2022 kern.notice kernel: [ 8.755409] random: jshn: uninitialized urandom read (4 bytes read, 15 bits of entropy available)
Sun Nov 20 16:11:42 2022 kern.notice kernel: [ 8.817276] random: ubusd: uninitialized urandom read (4 bytes read, 15 bits of entropy available)
Sun Nov 20 16:11:42 2022 kern.notice kernel: [ 8.846242] random: ubusd: uninitialized urandom read (4 bytes read, 15 bits of entropy available)
Sun Nov 20 16:11:42 2022 kern.notice kernel: [ 8.903182] random: ubusd: uninitialized urandom read (4 bytes read, 15 bits of entropy available)
Sun Nov 20 16:11:42 2022 kern.notice kernel: [ 8.913325] random: ubusd: uninitialized urandom read (4 bytes read, 15 bits of entropy available)
Sun Nov 20 16:11:42 2022 kern.notice kernel: [ 8.922747] random: ubusd: uninitialized urandom read (4 bytes read, 15 bits of entropy available)
Sun Nov 20 16:11:42 2022 kern.notice kernel: [ 8.932294] random: ubusd: uninitialized urandom read (4 bytes read, 15 bits of entropy available)
Sun Nov 20 16:11:42 2022 kern.notice kernel: [ 8.941883] random: ubusd: uninitialized urandom read (4 bytes read, 15 bits of entropy available)
Sun Nov 20 16:11:42 2022 user.info kernel: [ 8.966081] procd: - init -
Sun Nov 20 16:11:42 2022 user.info kernel: [ 9.834294] kmodloader: loading kernel modules from /etc/modules.d/*
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 9.864197] usbcore: registered new interface driver cdc_wdm
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 9.879543] Loading modules backported from Linux version wt-2017-01-31-0-ge882dff19e7f
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 9.887884] Backport generated by backports.git backports-20160324-13-g24da7d3c
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 9.923205] nf_conntrack version 0.5.0 (433 buckets, 1732 max)
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 10.045727] usbcore: registered new interface driver usbserial
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 10.051863] usbcore: registered new interface driver usbserial_generic
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 10.058789] usbserial: USB Serial support registered for generic
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 10.138817] xt_time: kernel timezone is -0000
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 10.152601] usbcore: registered new interface driver cdc_ether
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 10.169446] usbcore: registered new interface driver cdc_ncm
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 10.237276] usbcore: registered new interface driver huawei_cdc_ncm
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 10.255340] ip_tables: (C) 2000-2006 Netfilter Core Team
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 10.395395] PPP generic driver version 2.4.2
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 10.413755] usbcore: registered new interface driver qmi_wwan
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 10.428759] usbcore: registered new interface driver rndis_host
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 10.448019] usbcore: registered new interface driver sierra
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 10.453905] usbserial: USB Serial support registered for Sierra USB modem
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 10.483788] usbcore: registered new interface driver sierra_net
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 10.570255] usbcore: registered new interface driver option
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 10.576224] usbserial: USB Serial support registered for GSM modem (1-port)
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 10.607044] usbcore: registered new interface driver qcserial
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 10.613106] usbserial: USB Serial support registered for Qualcomm USB modem
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 10.717699] usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 10.725301] usbcore: registered new interface driver ath9k_htc
Sun Nov 20 16:11:42 2022 kern.debug kernel: [ 10.803114] ath: EEPROM regdomain: 0x0
Sun Nov 20 16:11:42 2022 kern.debug kernel: [ 10.803139] ath: EEPROM indicates default country code should be used
Sun Nov 20 16:11:42 2022 kern.debug kernel: [ 10.803150] ath: doing EEPROM country->regdmn map search
Sun Nov 20 16:11:42 2022 kern.debug kernel: [ 10.803173] ath: country maps to regdmn code: 0x3a
Sun Nov 20 16:11:42 2022 kern.debug kernel: [ 10.803186] ath: Country alpha2 being used: US
Sun Nov 20 16:11:42 2022 kern.debug kernel: [ 10.803196] ath: Regpair used: 0x3a
Sun Nov 20 16:11:42 2022 kern.debug kernel: [ 10.816934] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 10.823036] ieee80211 phy0: Atheros AR9340 Rev:3 mem=0xb8100000, irq=47
Sun Nov 20 16:11:42 2022 user.info kernel: [ 10.886008] kmodloader: done loading kernel modules from /etc/modules.d/*
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 11.209947] usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 11.460798] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 11.816545] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.4
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 11.822277] ath9k_htc 1-1:1.0: FW RMW support: On
Sun Nov 20 16:11:42 2022 kern.debug kernel: [ 11.827175] ath: EEPROM regdomain: 0x809c
Sun Nov 20 16:11:42 2022 kern.debug kernel: [ 11.827186] ath: EEPROM indicates we should expect a country code
Sun Nov 20 16:11:42 2022 kern.debug kernel: [ 11.827200] ath: doing EEPROM country->regdmn map search
Sun Nov 20 16:11:42 2022 kern.debug kernel: [ 11.827212] ath: country maps to regdmn code: 0x52
Sun Nov 20 16:11:42 2022 kern.debug kernel: [ 11.827224] ath: Country alpha2 being used: CN
Sun Nov 20 16:11:42 2022 kern.debug kernel: [ 11.827235] ath: Regpair used: 0x52
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 11.855323] ieee80211 phy1: Atheros AR9271 Rev:1
Sun Nov 20 16:11:45 2022 user.notice : Added device handler type: 8021ad
Sun Nov 20 16:11:45 2022 user.notice : Added device handler type: 8021q
Sun Nov 20 16:11:45 2022 user.notice : Added device handler type: macvlan
Sun Nov 20 16:11:45 2022 user.notice : Added device handler type: bridge
Sun Nov 20 16:11:45 2022 user.notice : Added device handler type: Network device
Sun Nov 20 16:11:45 2022 user.notice : Added device handler type: tunnel
Sun Nov 20 16:11:47 2022 authpriv.info dropbear[942]: Not backgrounding
Sun Nov 20 16:11:48 2022 daemon.notice procd: /etc/rc.d/S96led: setting up led WAN
Sun Nov 20 16:11:48 2022 daemon.notice procd: /etc/rc.d/S96led: setting up led LAN
Sun Nov 20 16:11:48 2022 daemon.notice procd: /etc/rc.d/S96led: setting up led WLAN
Sun Nov 20 16:11:48 2022 daemon.notice procd: /etc/rc.d/S96led: setting up led USB
Sun Nov 20 16:11:50 2022 kern.info kernel: [ 20.863568] device eth1 entered promiscuous mode
Sun Nov 20 16:11:50 2022 kern.info kernel: [ 20.890965] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
Sun Nov 20 16:11:50 2022 daemon.notice netifd: Interface 'lan' is enabled
Sun Nov 20 16:11:50 2022 daemon.notice netifd: Interface 'lan' is setting up now
Sun Nov 20 16:11:50 2022 daemon.notice netifd: Interface 'lan' is now up
Sun Nov 20 16:11:50 2022 daemon.notice netifd: Interface 'loopback' is enabled
Sun Nov 20 16:11:50 2022 daemon.notice netifd: Interface 'loopback' is setting up now
Sun Nov 20 16:11:50 2022 daemon.notice netifd: Interface 'loopback' is now up
Sun Nov 20 16:11:50 2022 daemon.notice netifd: Interface 'wan' is enabled
Sun Nov 20 16:11:50 2022 kern.info kernel: [ 20.946105] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
Sun Nov 20 16:11:50 2022 daemon.notice netifd: Interface 'wan6' is enabled
Sun Nov 20 16:11:50 2022 daemon.notice netifd: Network device 'lo' link is up
Sun Nov 20 16:11:50 2022 daemon.notice netifd: Interface 'loopback' has link connectivity
Sun Nov 20 16:11:51 2022 user.notice firewall: Reloading firewall due to ifup of lan (br-lan)
Sun Nov 20 16:11:52 2022 kern.info kernel: [ 22.456806] eth1: link up (1000Mbps/Full duplex)
Sun Nov 20 16:11:52 2022 kern.info kernel: [ 22.461646] br-lan: port 1(eth1) entered forwarding state
Sun Nov 20 16:11:52 2022 kern.info kernel: [ 22.467316] br-lan: port 1(eth1) entered forwarding state
Sun Nov 20 16:11:52 2022 daemon.notice netifd: Network device 'eth1' link is up
Sun Nov 20 16:11:52 2022 daemon.notice netifd: bridge 'br-lan' link is up
Sun Nov 20 16:11:52 2022 daemon.notice netifd: Interface 'lan' has link connectivity
Sun Nov 20 16:11:52 2022 kern.info kernel: [ 22.529525] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
Sun Nov 20 16:11:52 2022 daemon.info procd: - init complete -
Sun Nov 20 16:11:53 2022 daemon.err hostapd: Configuration file: /var/run/hostapd-phy1.conf
Sun Nov 20 16:11:54 2022 kern.info kernel: [ 24.465505] br-lan: port 1(eth1) entered forwarding state
Sun Nov 20 16:11:54 2022 kern.info kernel: [ 24.535013] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
Sun Nov 20 16:11:54 2022 kern.info kernel: [ 24.569871] device wlan1 entered promiscuous mode
Sun Nov 20 16:11:54 2022 daemon.notice hostapd: wlan1: interface state UNINITIALIZED->COUNTRY_UPDATE
Sun Nov 20 16:11:54 2022 daemon.err hostapd: Configuration file: /var/run/hostapd-phy0.conf
Sun Nov 20 16:11:54 2022 kern.info kernel: [ 24.739951] IPv6: ADDRCONF(NETDEV_UP): wlan0-1: link is not ready
Sun Nov 20 16:11:54 2022 kern.info kernel: [ 24.844123] device wlan0-1 entered promiscuous mode
Sun Nov 20 16:11:54 2022 kern.info kernel: [ 24.849417] br-lan: port 3(wlan0-1) entered forwarding state
Sun Nov 20 16:11:54 2022 kern.info kernel: [ 24.855314] br-lan: port 3(wlan0-1) entered forwarding state
Sun Nov 20 16:11:54 2022 daemon.notice hostapd: wlan0-1: interface state UNINITIALIZED->COUNTRY_UPDATE
Sun Nov 20 16:11:54 2022 daemon.notice hostapd: handle_probe_req: send failed
Sun Nov 20 16:11:55 2022 kern.info kernel: [ 25.557744] br-lan: port 3(wlan0-1) entered disabled state
Sun Nov 20 16:11:58 2022 daemon.notice hostapd: handle_probe_req: send failed
Sun Nov 20 16:11:58 2022 daemon.info dnsmasq[1369]: started, version 2.78 cachesize 150
Sun Nov 20 16:11:58 2022 daemon.info dnsmasq[1369]: DNS service limited to local subnets
Sun Nov 20 16:11:58 2022 daemon.info dnsmasq[1369]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth no-DNSSEC no-ID loop-detect inotify
Sun Nov 20 16:11:58 2022 daemon.info dnsmasq-dhcp[1369]: DHCP, IP range 192.168.11.100 -- 192.168.11.249, lease time 12h
Sun Nov 20 16:11:58 2022 daemon.info dnsmasq[1369]: using local addresses only for domain lan
Sun Nov 20 16:11:58 2022 daemon.warn dnsmasq[1369]: no servers found in /tmp/resolv.conf.auto, will retry
Sun Nov 20 16:11:58 2022 daemon.info dnsmasq[1369]: read /etc/hosts - 4 addresses
Sun Nov 20 16:11:58 2022 daemon.info dnsmasq[1369]: read /tmp/hosts/dhcp.cfg02411c - 2 addresses
Sun Nov 20 16:11:58 2022 daemon.info dnsmasq-dhcp[1369]: read /etc/ethers - 0 addresses
Sun Nov 20 16:11:59 2022 daemon.err hostapd: Using interface wlan1 with hwaddr a4:2b:8c:2c:40:9f and ssid "Borys"
Sun Nov 20 16:11:59 2022 daemon.err hostapd: Using interface wlan0-1 with hwaddr a4:2b:8c:2a:40:9f and ssid "Wi-Fi"
Sun Nov 20 16:11:59 2022 kern.info kernel: [ 30.283712] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
Sun Nov 20 16:11:59 2022 kern.info kernel: [ 30.290703] br-lan: port 2(wlan1) entered forwarding state
Sun Nov 20 16:11:59 2022 kern.info kernel: [ 30.296478] br-lan: port 2(wlan1) entered forwarding state
Sun Nov 20 16:11:59 2022 daemon.notice hostapd: wlan1: interface state COUNTRY_UPDATE->ENABLED
Sun Nov 20 16:11:59 2022 daemon.notice hostapd: wlan1: AP-ENABLED
Sun Nov 20 16:12:00 2022 daemon.notice netifd: Network device 'wlan1' link is up
Sun Nov 20 16:12:00 2022 daemon.notice hostapd: wlan0-1: interface state COUNTRY_UPDATE->ENABLED
Sun Nov 20 16:12:00 2022 daemon.notice hostapd: wlan0-1: AP-ENABLED
Sun Nov 20 16:12:00 2022 kern.info kernel: [ 30.796415] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
Sun Nov 20 16:12:00 2022 daemon.notice netifd: radio0 (1046): Successfully initialized wpa_supplicant
Sun Nov 20 16:12:01 2022 daemon.notice netifd: Interface 'wwan' is enabled
Sun Nov 20 16:12:01 2022 kern.info kernel: [ 32.137141] wlan0: authenticate with a4:2b:8c:2e:40:9f
Sun Nov 20 16:12:01 2022 kern.info kernel: [ 32.160504] wlan0: send auth to a4:2b:8c:2e:40:9f (try 1/3)
Sun Nov 20 16:12:01 2022 kern.info kernel: [ 32.172932] wlan0: authenticated
Sun Nov 20 16:12:01 2022 kern.info kernel: [ 32.185540] wlan0: associate with a4:2b:8c:2e:40:9f (try 1/3)
Sun Nov 20 16:12:01 2022 kern.info kernel: [ 32.197435] wlan0: RX AssocResp from a4:2b:8c:2e:40:9f (capab=0x411 status=0 aid=1)
Sun Nov 20 16:12:01 2022 kern.info kernel: [ 32.205780] wlan0: associated
Sun Nov 20 16:12:01 2022 kern.info kernel: [ 32.209309] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
Sun Nov 20 16:12:01 2022 daemon.notice netifd: Network device 'wlan0' link is up
Sun Nov 20 16:12:01 2022 daemon.notice netifd: Interface 'wwan' has link connectivity
Sun Nov 20 16:12:01 2022 daemon.notice netifd: Interface 'wwan' is setting up now
Sun Nov 20 16:12:01 2022 kern.info kernel: [ 32.295527] br-lan: port 2(wlan1) entered forwarding state
Sun Nov 20 16:12:02 2022 daemon.notice netifd: wwan (1425): udhcpc: started, v1.25.1
Sun Nov 20 16:12:02 2022 daemon.notice netifd: wwan (1425): udhcpc: sending discover
Sun Nov 20 16:12:02 2022 kern.info kernel: [ 32.884075] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0-1: link becomes ready
Sun Nov 20 16:12:02 2022 kern.info kernel: [ 32.891090] br-lan: port 3(wlan0-1) entered forwarding state
Sun Nov 20 16:12:02 2022 kern.info kernel: [ 32.897094] br-lan: port 3(wlan0-1) entered forwarding state
Sun Nov 20 16:12:02 2022 daemon.notice netifd: Network device 'wlan0-1' link is up
Sun Nov 20 16:12:03 2022 daemon.info dnsmasq-dhcp[1369]: DHCPREQUEST(br-lan) 192.168.11.172 00:24:81:53:40:0e
Sun Nov 20 16:12:03 2022 daemon.info dnsmasq-dhcp[1369]: DHCPACK(br-lan) 192.168.11.172 00:24:81:53:40:0e M-J-PC
Sun Nov 20 16:12:04 2022 kern.info kernel: [ 34.895481] br-lan: port 3(wlan0-1) entered forwarding state
Sun Nov 20 16:12:05 2022 daemon.notice netifd: wwan (1425): udhcpc: sending discover
Sun Nov 20 16:12:05 2022 daemon.notice netifd: wwan (1425): udhcpc: sending select for 192.168.12.155
Sun Nov 20 16:12:05 2022 daemon.notice netifd: wwan (1425): udhcpc: lease of 192.168.12.155 obtained, lease time 86400
Sun Nov 20 16:12:05 2022 daemon.notice netifd: Interface 'wwan' is now up
Sun Nov 20 16:12:05 2022 daemon.info dnsmasq[1369]: reading /tmp/resolv.conf.auto
Sun Nov 20 16:12:05 2022 daemon.info dnsmasq[1369]: using local addresses only for domain lan
Sun Nov 20 16:12:05 2022 daemon.info dnsmasq[1369]: using nameserver 192.168.12.100#53
Sun Nov 20 16:12:05 2022 daemon.info dnsmasq[1369]: using nameserver 192.168.12.100#53
Sun Nov 20 16:12:05 2022 user.notice firewall: Reloading firewall due to ifup of wwan (wlan0)
Sun Nov 20 16:12:08 2022 kern.notice kernel: [ 38.730568] random: nonblocking pool is initialized
Sun Nov 20 16:14:16 2022 daemon.warn dnsmasq[1369]: nameserver 192.168.12.100 refused to do a recursive query
Sun Nov 20 16:14:16 2022 daemon.warn dnsmasq[1369]: nameserver 192.168.12.100 refused to do a recursive query
Sun Nov 20 16:14:32 2022 authpriv.info dropbear[1534]: Child connection from 192.168.11.172:6205
Sun Nov 20 16:14:38 2022 daemon.info dnsmasq[1369]: read /etc/hosts - 4 addresses
Sun Nov 20 16:14:38 2022 daemon.info dnsmasq[1369]: read /tmp/hosts/dhcp.cfg02411c - 2 addresses
Sun Nov 20 16:14:38 2022 daemon.info dnsmasq-dhcp[1369]: read /etc/ethers - 0 addresses
Sun Nov 20 16:14:39 2022 authpriv.notice dropbear[1534]: Password auth succeeded for 'root' from 192.168.11.172:6205
root@Router:~#

2.

| radio0: mode: ap, ssid: Wi-Fi, channel: 11, conn: 0 |
| radio1: mode: ap, ssid: Borys, channel: 8, conn: 0 |
| radio0: mode: sta, ssid: Wi-Fi, channel: 11, conn: 1 |
-----------------------------------------------------------------------------
root@Router:~# logread
Sun Nov 20 16:11:42 2022 kern.notice kernel: [ 0.000000] Linux version 4.4.140 (cezary@eko.one.pl) (gcc version 5.4.0 (LEDE GCC 5.4.0 r3785-ceea0ac) ) #0 Tue Jul 17 05:17:48 2018
Sun Nov 20 16:11:42 2022 kern.debug kernel: [ 0.000000] MyLoader: sysp=e72c40a6, boardp=3050a00a, parts=15d661ab
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.000000] bootconsole [early0] enabled
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.000000] CPU0 revision is: 0001974c (MIPS 74Kc)
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.000000] SoC: Atheros AR9341 rev 3
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.000000] Determined physical RAM map:
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.000000] memory: 02000000 @ 00000000 (usable)
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.000000] Initrd not found or empty - disabling initrd
Sun Nov 20 16:11:42 2022 kern.warn kernel: [ 0.000000] No valid device tree found, continuing without
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.000000] Zone ranges:
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000001ffffff]
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.000000] Movable zone start for each node
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.000000] Early memory node ranges
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000001ffffff]
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000001ffffff]
Sun Nov 20 16:11:42 2022 kern.debug kernel: [ 0.000000] On node 0 totalpages: 8192
Sun Nov 20 16:11:42 2022 kern.debug kernel: [ 0.000000] free_area_init_node: node 0, pgdat 8043a4b0, node_mem_map 81000000
Sun Nov 20 16:11:42 2022 kern.debug kernel: [ 0.000000] Normal zone: 64 pages used for memmap
Sun Nov 20 16:11:42 2022 kern.debug kernel: [ 0.000000] Normal zone: 0 pages reserved
Sun Nov 20 16:11:42 2022 kern.debug kernel: [ 0.000000] Normal zone: 8192 pages, LIFO batch:0
Sun Nov 20 16:11:42 2022 kern.warn kernel: [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Sun Nov 20 16:11:42 2022 kern.warn kernel: [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Sun Nov 20 16:11:42 2022 kern.debug kernel: [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
Sun Nov 20 16:11:42 2022 kern.debug kernel: [ 0.000000] pcpu-alloc: [0] 0
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
Sun Nov 20 16:11:42 2022 kern.notice kernel: [ 0.000000] Kernel command line: board=TL-MR3420-v2 console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.000000] Writing ErrCtl register=00000000
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.000000] Readback ErrCtl register=00000000
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.000000] Memory: 27416K/32768K available (3130K kernel code, 162K rwdata, 780K rodata, 336K init, 205K bss, 5352K reserved, 0K cma-reserved)
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.000000] NR_IRQS:51
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.000000] Clocks: CPU:535.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7144898866 ns
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.000011] sched_clock: 32 bits at 267MHz, resolution 3ns, wraps every 8027976190ns
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.008234] Calibrating delay loop... 266.64 BogoMIPS (lpj=1333248)
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.091044] pid_max: default: 32768 minimum: 301
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.096053] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.103039] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.113530] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.123958] futex hash table entries: 256 (order: -1, 3072 bytes)
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.131822] NET: Registered protocol family 16
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.138310] MIPS: machine is TP-LINK TL-MR3420 v2
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.595449] clocksource: Switched to clocksource MIPS
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.602385] NET: Registered protocol family 2
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.608061] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.615423] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.622192] TCP: Hash tables configured (established 1024 bind 1024)
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.629002] UDP hash table entries: 256 (order: 0, 4096 bytes)
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.635179] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.642180] NET: Registered protocol family 1
Sun Nov 20 16:11:42 2022 kern.debug kernel: [ 0.646911] PCI: CLS 0 bytes, default 32
Sun Nov 20 16:11:42 2022 kern.warn kernel: [ 0.652331] Crashlog allocated RAM at address 0x1f00000
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.675560] squashfs: version 4.0 (2009/01/31) Phillip Lougher
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.681732] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.695106] io scheduler noop registered
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.699316] io scheduler deadline registered (default)
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.705039] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.714901] console [ttyS0] disabled
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.738809] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 1562500) is a 16550A
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.747916] console [ttyS0] enabled
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.755477] bootconsole [early0] disabled
Sun Nov 20 16:11:42 2022 kern.warn kernel: [ 0.770199] m25p80 spi0.0: found en25q32b, expected m25p80
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.775953] m25p80 spi0.0: en25q32b (4096 Kbytes)
Sun Nov 20 16:11:42 2022 kern.notice kernel: [ 0.782145] 5 tp-link partitions found on MTD device spi0.0
Sun Nov 20 16:11:42 2022 kern.notice kernel: [ 0.787964] Creating 5 MTD partitions on "spi0.0":
Sun Nov 20 16:11:42 2022 kern.notice kernel: [ 0.792920] 0x000000000000-0x000000020000 : "u-boot"
Sun Nov 20 16:11:42 2022 kern.notice kernel: [ 0.799738] 0x000000020000-0x00000016ef94 : "kernel"
Sun Nov 20 16:11:42 2022 kern.notice kernel: [ 0.806813] 0x00000016ef94-0x0000003f0000 : "rootfs"
Sun Nov 20 16:11:42 2022 kern.notice kernel: [ 0.813803] mtd: device 2 (rootfs) set to be root filesystem
Sun Nov 20 16:11:42 2022 kern.notice kernel: [ 0.819768] 1 squashfs-split partitions found on MTD device rootfs
Sun Nov 20 16:11:42 2022 kern.notice kernel: [ 0.826178] 0x000000380000-0x0000003f0000 : "rootfs_data"
Sun Nov 20 16:11:42 2022 kern.notice kernel: [ 0.833671] 0x0000003f0000-0x000000400000 : "art"
Sun Nov 20 16:11:42 2022 kern.notice kernel: [ 0.840550] 0x000000020000-0x0000003f0000 : "firmware"
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 0.865929] libphy: ag71xx_mdio: probed
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 1.457546] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:00 [uid=004dd042, driver=Generic PHY]
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 1.467806] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 2.057331] ag71xx-mdio.1: Found an AR934X built-in switch
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 2.099689] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 2.109082] NET: Registered protocol family 10
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 2.119302] NET: Registered protocol family 17
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 2.123987] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 2.137212] 8021q: 802.1Q VLAN Support v1.8
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 2.143623] hctosys: unable to open rtc device (rtc0)
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 2.153931] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 2.163455] Freeing unused kernel memory: 336K
Sun Nov 20 16:11:42 2022 user.info kernel: [ 3.284967] init: Console is alive
Sun Nov 20 16:11:42 2022 user.info kernel: [ 3.288818] init: - watchdog -
Sun Nov 20 16:11:42 2022 user.info kernel: [ 4.471208] kmodloader: loading kernel modules from /etc/modules-boot.d/*
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 4.546821] usbcore: registered new interface driver usbfs
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 4.552606] usbcore: registered new interface driver hub
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 4.558289] usbcore: registered new device driver usb
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 4.570036] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 4.578722] ehci-platform: EHCI generic platform driver
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 4.584234] ehci-platform ehci-platform: EHCI Host Controller
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 4.590281] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 4.600592] ehci-platform ehci-platform: TX-TX IDP fix enabled
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 4.606662] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 4.625494] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 4.632985] hub 1-0:1.0: USB hub found
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 4.637399] hub 1-0:1.0: 1 port detected
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 4.644964] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 4.653171] ohci-platform: OHCI generic platform driver
Sun Nov 20 16:11:42 2022 user.info kernel: [ 4.659528] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
Sun Nov 20 16:11:42 2022 user.info kernel: [ 4.677537] init: - preinit -
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 5.135787] usb 1-1: new high-speed USB device number 2 using ehci-platform
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 5.240580] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
Sun Nov 20 16:11:42 2022 kern.notice kernel: [ 5.270480] random: procd: uninitialized urandom read (4 bytes read, 8 bits of entropy available)
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 6.836718] eth1: link up (1000Mbps/Full duplex)
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 6.841531] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
Sun Nov 20 16:11:42 2022 kern.notice kernel: [ 7.591870] jffs2: notice: (399) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
Sun Nov 20 16:11:42 2022 user.info kernel: [ 7.610104] mount_root: switching to jffs2 overlay
Sun Nov 20 16:11:42 2022 user.warn kernel: [ 7.624598] urandom-seed: Seeding with /etc/urandom.seed
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 7.833111] eth1: link down
Sun Nov 20 16:11:42 2022 user.info kernel: [ 7.849961] procd: - early -
Sun Nov 20 16:11:42 2022 user.info kernel: [ 7.853063] procd: - watchdog -
Sun Nov 20 16:11:42 2022 kern.notice kernel: [ 8.422089] random: jshn: uninitialized urandom read (4 bytes read, 14 bits of entropy available)
Sun Nov 20 16:11:42 2022 user.info kernel: [ 8.607117] procd: - watchdog -
Sun Nov 20 16:11:42 2022 user.info kernel: [ 8.610703] procd: - ubus -
Sun Nov 20 16:11:42 2022 kern.notice kernel: [ 8.755409] random: jshn: uninitialized urandom read (4 bytes read, 15 bits of entropy available)
Sun Nov 20 16:11:42 2022 kern.notice kernel: [ 8.817276] random: ubusd: uninitialized urandom read (4 bytes read, 15 bits of entropy available)
Sun Nov 20 16:11:42 2022 kern.notice kernel: [ 8.846242] random: ubusd: uninitialized urandom read (4 bytes read, 15 bits of entropy available)
Sun Nov 20 16:11:42 2022 kern.notice kernel: [ 8.903182] random: ubusd: uninitialized urandom read (4 bytes read, 15 bits of entropy available)
Sun Nov 20 16:11:42 2022 kern.notice kernel: [ 8.913325] random: ubusd: uninitialized urandom read (4 bytes read, 15 bits of entropy available)
Sun Nov 20 16:11:42 2022 kern.notice kernel: [ 8.922747] random: ubusd: uninitialized urandom read (4 bytes read, 15 bits of entropy available)
Sun Nov 20 16:11:42 2022 kern.notice kernel: [ 8.932294] random: ubusd: uninitialized urandom read (4 bytes read, 15 bits of entropy available)
Sun Nov 20 16:11:42 2022 kern.notice kernel: [ 8.941883] random: ubusd: uninitialized urandom read (4 bytes read, 15 bits of entropy available)
Sun Nov 20 16:11:42 2022 user.info kernel: [ 8.966081] procd: - init -
Sun Nov 20 16:11:42 2022 user.info kernel: [ 9.834294] kmodloader: loading kernel modules from /etc/modules.d/*
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 9.864197] usbcore: registered new interface driver cdc_wdm
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 9.879543] Loading modules backported from Linux version wt-2017-01-31-0-ge882dff19e7f
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 9.887884] Backport generated by backports.git backports-20160324-13-g24da7d3c
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 9.923205] nf_conntrack version 0.5.0 (433 buckets, 1732 max)
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 10.045727] usbcore: registered new interface driver usbserial
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 10.051863] usbcore: registered new interface driver usbserial_generic
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 10.058789] usbserial: USB Serial support registered for generic
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 10.138817] xt_time: kernel timezone is -0000
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 10.152601] usbcore: registered new interface driver cdc_ether
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 10.169446] usbcore: registered new interface driver cdc_ncm
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 10.237276] usbcore: registered new interface driver huawei_cdc_ncm
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 10.255340] ip_tables: (C) 2000-2006 Netfilter Core Team
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 10.395395] PPP generic driver version 2.4.2
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 10.413755] usbcore: registered new interface driver qmi_wwan
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 10.428759] usbcore: registered new interface driver rndis_host
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 10.448019] usbcore: registered new interface driver sierra
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 10.453905] usbserial: USB Serial support registered for Sierra USB modem
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 10.483788] usbcore: registered new interface driver sierra_net
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 10.570255] usbcore: registered new interface driver option
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 10.576224] usbserial: USB Serial support registered for GSM modem (1-port)
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 10.607044] usbcore: registered new interface driver qcserial
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 10.613106] usbserial: USB Serial support registered for Qualcomm USB modem
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 10.717699] usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 10.725301] usbcore: registered new interface driver ath9k_htc
Sun Nov 20 16:11:42 2022 kern.debug kernel: [ 10.803114] ath: EEPROM regdomain: 0x0
Sun Nov 20 16:11:42 2022 kern.debug kernel: [ 10.803139] ath: EEPROM indicates default country code should be used
Sun Nov 20 16:11:42 2022 kern.debug kernel: [ 10.803150] ath: doing EEPROM country->regdmn map search
Sun Nov 20 16:11:42 2022 kern.debug kernel: [ 10.803173] ath: country maps to regdmn code: 0x3a
Sun Nov 20 16:11:42 2022 kern.debug kernel: [ 10.803186] ath: Country alpha2 being used: US
Sun Nov 20 16:11:42 2022 kern.debug kernel: [ 10.803196] ath: Regpair used: 0x3a
Sun Nov 20 16:11:42 2022 kern.debug kernel: [ 10.816934] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 10.823036] ieee80211 phy0: Atheros AR9340 Rev:3 mem=0xb8100000, irq=47
Sun Nov 20 16:11:42 2022 user.info kernel: [ 10.886008] kmodloader: done loading kernel modules from /etc/modules.d/*
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 11.209947] usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 11.460798] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 11.816545] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.4
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 11.822277] ath9k_htc 1-1:1.0: FW RMW support: On
Sun Nov 20 16:11:42 2022 kern.debug kernel: [ 11.827175] ath: EEPROM regdomain: 0x809c
Sun Nov 20 16:11:42 2022 kern.debug kernel: [ 11.827186] ath: EEPROM indicates we should expect a country code
Sun Nov 20 16:11:42 2022 kern.debug kernel: [ 11.827200] ath: doing EEPROM country->regdmn map search
Sun Nov 20 16:11:42 2022 kern.debug kernel: [ 11.827212] ath: country maps to regdmn code: 0x52
Sun Nov 20 16:11:42 2022 kern.debug kernel: [ 11.827224] ath: Country alpha2 being used: CN
Sun Nov 20 16:11:42 2022 kern.debug kernel: [ 11.827235] ath: Regpair used: 0x52
Sun Nov 20 16:11:42 2022 kern.info kernel: [ 11.855323] ieee80211 phy1: Atheros AR9271 Rev:1
Sun Nov 20 16:11:45 2022 user.notice : Added device handler type: 8021ad
Sun Nov 20 16:11:45 2022 user.notice : Added device handler type: 8021q
Sun Nov 20 16:11:45 2022 user.notice : Added device handler type: macvlan
Sun Nov 20 16:11:45 2022 user.notice : Added device handler type: bridge
Sun Nov 20 16:11:45 2022 user.notice : Added device handler type: Network device
Sun Nov 20 16:11:45 2022 user.notice : Added device handler type: tunnel
Sun Nov 20 16:11:47 2022 authpriv.info dropbear[942]: Not backgrounding
Sun Nov 20 16:11:48 2022 daemon.notice procd: /etc/rc.d/S96led: setting up led WAN
Sun Nov 20 16:11:48 2022 daemon.notice procd: /etc/rc.d/S96led: setting up led LAN
Sun Nov 20 16:11:48 2022 daemon.notice procd: /etc/rc.d/S96led: setting up led WLAN
Sun Nov 20 16:11:48 2022 daemon.notice procd: /etc/rc.d/S96led: setting up led USB
Sun Nov 20 16:11:50 2022 kern.info kernel: [ 20.863568] device eth1 entered promiscuous mode
Sun Nov 20 16:11:50 2022 kern.info kernel: [ 20.890965] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
Sun Nov 20 16:11:50 2022 daemon.notice netifd: Interface 'lan' is enabled
Sun Nov 20 16:11:50 2022 daemon.notice netifd: Interface 'lan' is setting up now
Sun Nov 20 16:11:50 2022 daemon.notice netifd: Interface 'lan' is now up
Sun Nov 20 16:11:50 2022 daemon.notice netifd: Interface 'loopback' is enabled
Sun Nov 20 16:11:50 2022 daemon.notice netifd: Interface 'loopback' is setting up now
Sun Nov 20 16:11:50 2022 daemon.notice netifd: Interface 'loopback' is now up
Sun Nov 20 16:11:50 2022 daemon.notice netifd: Interface 'wan' is enabled
Sun Nov 20 16:11:50 2022 kern.info kernel: [ 20.946105] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
Sun Nov 20 16:11:50 2022 daemon.notice netifd: Interface 'wan6' is enabled
Sun Nov 20 16:11:50 2022 daemon.notice netifd: Network device 'lo' link is up
Sun Nov 20 16:11:50 2022 daemon.notice netifd: Interface 'loopback' has link connectivity
Sun Nov 20 16:11:51 2022 user.notice firewall: Reloading firewall due to ifup of lan (br-lan)
Sun Nov 20 16:11:52 2022 kern.info kernel: [ 22.456806] eth1: link up (1000Mbps/Full duplex)
Sun Nov 20 16:11:52 2022 kern.info kernel: [ 22.461646] br-lan: port 1(eth1) entered forwarding state
Sun Nov 20 16:11:52 2022 kern.info kernel: [ 22.467316] br-lan: port 1(eth1) entered forwarding state
Sun Nov 20 16:11:52 2022 daemon.notice netifd: Network device 'eth1' link is up
Sun Nov 20 16:11:52 2022 daemon.notice netifd: bridge 'br-lan' link is up
Sun Nov 20 16:11:52 2022 daemon.notice netifd: Interface 'lan' has link connectivity
Sun Nov 20 16:11:52 2022 kern.info kernel: [ 22.529525] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
Sun Nov 20 16:11:52 2022 daemon.info procd: - init complete -
Sun Nov 20 16:11:53 2022 daemon.err hostapd: Configuration file: /var/run/hostapd-phy1.conf
Sun Nov 20 16:11:54 2022 kern.info kernel: [ 24.465505] br-lan: port 1(eth1) entered forwarding state
Sun Nov 20 16:11:54 2022 kern.info kernel: [ 24.535013] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
Sun Nov 20 16:11:54 2022 kern.info kernel: [ 24.569871] device wlan1 entered promiscuous mode
Sun Nov 20 16:11:54 2022 daemon.notice hostapd: wlan1: interface state UNINITIALIZED->COUNTRY_UPDATE
Sun Nov 20 16:11:54 2022 daemon.err hostapd: Configuration file: /var/run/hostapd-phy0.conf
Sun Nov 20 16:11:54 2022 kern.info kernel: [ 24.739951] IPv6: ADDRCONF(NETDEV_UP): wlan0-1: link is not ready
Sun Nov 20 16:11:54 2022 kern.info kernel: [ 24.844123] device wlan0-1 entered promiscuous mode
Sun Nov 20 16:11:54 2022 kern.info kernel: [ 24.849417] br-lan: port 3(wlan0-1) entered forwarding state
Sun Nov 20 16:11:54 2022 kern.info kernel: [ 24.855314] br-lan: port 3(wlan0-1) entered forwarding state
Sun Nov 20 16:11:54 2022 daemon.notice hostapd: wlan0-1: interface state UNINITIALIZED->COUNTRY_UPDATE
Sun Nov 20 16:11:54 2022 daemon.notice hostapd: handle_probe_req: send failed
Sun Nov 20 16:11:55 2022 kern.info kernel: [ 25.557744] br-lan: port 3(wlan0-1) entered disabled state
Sun Nov 20 16:11:58 2022 daemon.notice hostapd: handle_probe_req: send failed
Sun Nov 20 16:11:58 2022 daemon.info dnsmasq[1369]: started, version 2.78 cachesize 150
Sun Nov 20 16:11:58 2022 daemon.info dnsmasq[1369]: DNS service limited to local subnets
Sun Nov 20 16:11:58 2022 daemon.info dnsmasq[1369]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth no-DNSSEC no-ID loop-detect inotify
Sun Nov 20 16:11:58 2022 daemon.info dnsmasq-dhcp[1369]: DHCP, IP range 192.168.11.100 -- 192.168.11.249, lease time 12h
Sun Nov 20 16:11:58 2022 daemon.info dnsmasq[1369]: using local addresses only for domain lan
Sun Nov 20 16:11:58 2022 daemon.warn dnsmasq[1369]: no servers found in /tmp/resolv.conf.auto, will retry
Sun Nov 20 16:11:58 2022 daemon.info dnsmasq[1369]: read /etc/hosts - 4 addresses
Sun Nov 20 16:11:58 2022 daemon.info dnsmasq[1369]: read /tmp/hosts/dhcp.cfg02411c - 2 addresses
Sun Nov 20 16:11:58 2022 daemon.info dnsmasq-dhcp[1369]: read /etc/ethers - 0 addresses
Sun Nov 20 16:11:59 2022 daemon.err hostapd: Using interface wlan1 with hwaddr a4:2b:8c:2c:40:9f and ssid "Borys"
Sun Nov 20 16:11:59 2022 daemon.err hostapd: Using interface wlan0-1 with hwaddr a4:2b:8c:2a:40:9f and ssid "Wi-Fi"
Sun Nov 20 16:11:59 2022 kern.info kernel: [ 30.283712] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
Sun Nov 20 16:11:59 2022 kern.info kernel: [ 30.290703] br-lan: port 2(wlan1) entered forwarding state
Sun Nov 20 16:11:59 2022 kern.info kernel: [ 30.296478] br-lan: port 2(wlan1) entered forwarding state
Sun Nov 20 16:11:59 2022 daemon.notice hostapd: wlan1: interface state COUNTRY_UPDATE->ENABLED
Sun Nov 20 16:11:59 2022 daemon.notice hostapd: wlan1: AP-ENABLED
Sun Nov 20 16:12:00 2022 daemon.notice netifd: Network device 'wlan1' link is up
Sun Nov 20 16:12:00 2022 daemon.notice hostapd: wlan0-1: interface state COUNTRY_UPDATE->ENABLED
Sun Nov 20 16:12:00 2022 daemon.notice hostapd: wlan0-1: AP-ENABLED
Sun Nov 20 16:12:00 2022 kern.info kernel: [ 30.796415] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
Sun Nov 20 16:12:00 2022 daemon.notice netifd: radio0 (1046): Successfully initialized wpa_supplicant
Sun Nov 20 16:12:01 2022 daemon.notice netifd: Interface 'wwan' is enabled
Sun Nov 20 16:12:01 2022 kern.info kernel: [ 32.137141] wlan0: authenticate with a4:2b:8c:2e:40:9f
Sun Nov 20 16:12:01 2022 kern.info kernel: [ 32.160504] wlan0: send auth to a4:2b:8c:2e:40:9f (try 1/3)
Sun Nov 20 16:12:01 2022 kern.info kernel: [ 32.172932] wlan0: authenticated
Sun Nov 20 16:12:01 2022 kern.info kernel: [ 32.185540] wlan0: associate with a4:2b:8c:2e:40:9f (try 1/3)
Sun Nov 20 16:12:01 2022 kern.info kernel: [ 32.197435] wlan0: RX AssocResp from a4:2b:8c:2e:40:9f (capab=0x411 status=0 aid=1)
Sun Nov 20 16:12:01 2022 kern.info kernel: [ 32.205780] wlan0: associated
Sun Nov 20 16:12:01 2022 kern.info kernel: [ 32.209309] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
Sun Nov 20 16:12:01 2022 daemon.notice netifd: Network device 'wlan0' link is up
Sun Nov 20 16:12:01 2022 daemon.notice netifd: Interface 'wwan' has link connectivity
Sun Nov 20 16:12:01 2022 daemon.notice netifd: Interface 'wwan' is setting up now
Sun Nov 20 16:12:01 2022 kern.info kernel: [ 32.295527] br-lan: port 2(wlan1) entered forwarding state
Sun Nov 20 16:12:02 2022 daemon.notice netifd: wwan (1425): udhcpc: started, v1.25.1
Sun Nov 20 16:12:02 2022 daemon.notice netifd: wwan (1425): udhcpc: sending discover
Sun Nov 20 16:12:02 2022 kern.info kernel: [ 32.884075] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0-1: link becomes ready
Sun Nov 20 16:12:02 2022 kern.info kernel: [ 32.891090] br-lan: port 3(wlan0-1) entered forwarding state
Sun Nov 20 16:12:02 2022 kern.info kernel: [ 32.897094] br-lan: port 3(wlan0-1) entered forwarding state
Sun Nov 20 16:12:02 2022 daemon.notice netifd: Network device 'wlan0-1' link is up
Sun Nov 20 16:12:03 2022 daemon.info dnsmasq-dhcp[1369]: DHCPREQUEST(br-lan) 192.168.11.172 00:24:81:53:40:0e
Sun Nov 20 16:12:03 2022 daemon.info dnsmasq-dhcp[1369]: DHCPACK(br-lan) 192.168.11.172 00:24:81:53:40:0e M-J-PC
Sun Nov 20 16:12:04 2022 kern.info kernel: [ 34.895481] br-lan: port 3(wlan0-1) entered forwarding state
Sun Nov 20 16:12:05 2022 daemon.notice netifd: wwan (1425): udhcpc: sending discover
Sun Nov 20 16:12:05 2022 daemon.notice netifd: wwan (1425): udhcpc: sending select for 192.168.12.155
Sun Nov 20 16:12:05 2022 daemon.notice netifd: wwan (1425): udhcpc: lease of 192.168.12.155 obtained, lease time 86400
Sun Nov 20 16:12:05 2022 daemon.notice netifd: Interface 'wwan' is now up
Sun Nov 20 16:12:05 2022 daemon.info dnsmasq[1369]: reading /tmp/resolv.conf.auto
Sun Nov 20 16:12:05 2022 daemon.info dnsmasq[1369]: using local addresses only for domain lan
Sun Nov 20 16:12:05 2022 daemon.info dnsmasq[1369]: using nameserver 192.168.12.100#53
Sun Nov 20 16:12:05 2022 daemon.info dnsmasq[1369]: using nameserver 192.168.12.100#53
Sun Nov 20 16:12:05 2022 user.notice firewall: Reloading firewall due to ifup of wwan (wlan0)
Sun Nov 20 16:12:08 2022 kern.notice kernel: [ 38.730568] random: nonblocking pool is initialized
Sun Nov 20 16:14:16 2022 daemon.warn dnsmasq[1369]: nameserver 192.168.12.100 refused to do a recursive query
Sun Nov 20 16:14:16 2022 daemon.warn dnsmasq[1369]: nameserver 192.168.12.100 refused to do a recursive query
Sun Nov 20 16:14:32 2022 authpriv.info dropbear[1534]: Child connection from 192.168.11.172:6205
Sun Nov 20 16:14:38 2022 daemon.info dnsmasq[1369]: read /etc/hosts - 4 addresses
Sun Nov 20 16:14:38 2022 daemon.info dnsmasq[1369]: read /tmp/hosts/dhcp.cfg02411c - 2 addresses
Sun Nov 20 16:14:38 2022 daemon.info dnsmasq-dhcp[1369]: read /etc/ethers - 0 addresses
Sun Nov 20 16:14:39 2022 authpriv.notice dropbear[1534]: Password auth succeeded for 'root' from 192.168.11.172:6205
Sun Nov 20 16:15:25 2022 kern.info kernel: [ 123.394633] eth1: link down
Sun Nov 20 16:15:25 2022 kern.info kernel: [ 123.397958] br-lan: port 1(eth1) entered disabled state
Sun Nov 20 16:15:25 2022 daemon.notice netifd: Network device 'eth1' link is down
Sun Nov 20 16:15:27 2022 daemon.info hostapd: wlan1: STA c2:f8:2b:06:aa:55 IEEE 802.11: authenticated
Sun Nov 20 16:15:27 2022 daemon.info hostapd: wlan1: STA c2:f8:2b:06:aa:55 IEEE 802.11: associated (aid 1)
Sun Nov 20 16:15:27 2022 daemon.notice hostapd: wlan1: AP-STA-CONNECTED c2:f8:2b:06:aa:55
Sun Nov 20 16:15:27 2022 daemon.info hostapd: wlan1: STA c2:f8:2b:06:aa:55 WPA: pairwise key handshake completed (RSN)
Sun Nov 20 16:15:27 2022 daemon.info dnsmasq-dhcp[1369]: DHCPREQUEST(br-lan) 192.168.12.152 c2:f8:2b:06:aa:55
Sun Nov 20 16:15:27 2022 daemon.info dnsmasq-dhcp[1369]: DHCPNAK(br-lan) 192.168.12.152 c2:f8:2b:06:aa:55 wrong network
Sun Nov 20 16:15:31 2022 daemon.info dnsmasq-dhcp[1369]: DHCPDISCOVER(br-lan) c2:f8:2b:06:aa:55
Sun Nov 20 16:15:31 2022 daemon.info dnsmasq-dhcp[1369]: DHCPOFFER(br-lan) 192.168.11.198 c2:f8:2b:06:aa:55
Sun Nov 20 16:15:31 2022 daemon.info dnsmasq-dhcp[1369]: DHCPREQUEST(br-lan) 192.168.11.198 c2:f8:2b:06:aa:55
Sun Nov 20 16:15:31 2022 daemon.info dnsmasq-dhcp[1369]: DHCPACK(br-lan) 192.168.11.198 c2:f8:2b:06:aa:55 M-J-PC
Sun Nov 20 16:15:55 2022 daemon.notice hostapd: wlan1: AP-STA-DISCONNECTED c2:f8:2b:06:aa:55
Sun Nov 20 16:15:55 2022 daemon.info hostapd: wlan1: STA c2:f8:2b:06:aa:55 IEEE 802.11: disassociated
Sun Nov 20 16:15:55 2022 kern.info kernel: [ 153.395916] eth1: link up (1000Mbps/Full duplex)
Sun Nov 20 16:15:55 2022 kern.info kernel: [ 153.400928] br-lan: port 1(eth1) entered forwarding state
Sun Nov 20 16:15:55 2022 kern.info kernel: [ 153.406648] br-lan: port 1(eth1) entered forwarding state
Sun Nov 20 16:15:55 2022 daemon.notice netifd: Network device 'eth1' link is up
Sun Nov 20 16:15:55 2022 daemon.info dnsmasq-dhcp[1369]: DHCPREQUEST(br-lan) 192.168.11.172 00:24:81:53:40:0e
Sun Nov 20 16:15:55 2022 daemon.info dnsmasq-dhcp[1369]: DHCPACK(br-lan) 192.168.11.172 00:24:81:53:40:0e M-J-PC
Sun Nov 20 16:15:56 2022 daemon.info hostapd: wlan1: STA c2:f8:2b:06:aa:55 IEEE 802.11: deauthenticated due to inactivity (timer DEAUTH/REMOVE)
Sun Nov 20 16:15:57 2022 kern.info kernel: [ 155.403758] br-lan: port 1(eth1) entered forwarding state
Sun Nov 20 16:21:15 2022 authpriv.info dropbear[1534]: Exit (root): Exited normally
Sun Nov 20 16:21:22 2022 authpriv.info dropbear[1714]: Child connection from 192.168.11.172:6239
Sun Nov 20 16:21:27 2022 authpriv.notice dropbear[1714]: Password auth succeeded for 'root' from 192.168.11.172:6239
Sun Nov 20 16:21:29 2022 kern.info kernel: [ 487.654881] usb 1-1: USB disconnect, device number 2
Sun Nov 20 16:21:30 2022 kern.err kernel: [ 487.768014] ath: phy1: RX failed to go idle in 10 ms RXSM=0x2000000
Sun Nov 20 16:21:30 2022 kern.err kernel: [ 487.879324] ath: phy1: RX failed to go idle in 10 ms RXSM=0x2000000
Sun Nov 20 16:21:30 2022 kern.err kernel: [ 487.988592] ath: phy1: RX failed to go idle in 10 ms RXSM=0x2000000
Sun Nov 20 16:21:30 2022 kern.err kernel: [ 488.098049] ath: phy1: RX failed to go idle in 10 ms RXSM=0x2000000
Sun Nov 20 16:21:30 2022 kern.info kernel: [ 488.104978] br-lan: port 2(wlan1) entered disabled state
Sun Nov 20 16:21:30 2022 daemon.notice hostapd: wlan1: INTERFACE-DISABLED
Sun Nov 20 16:21:30 2022 daemon.notice netifd: Network device 'wlan1' link is down
Sun Nov 20 16:21:30 2022 kern.info kernel: [ 488.119142] device wlan1 left promiscuous mode
Sun Nov 20 16:21:30 2022 kern.info kernel: [ 488.123858] br-lan: port 2(wlan1) entered disabled state
Sun Nov 20 16:21:30 2022 kern.info kernel: [ 488.136004] usb 1-1: ath9k_htc: USB layer deinitialized
Sun Nov 20 16:22:10 2022 kern.info kernel: [ 528.090097] usb 1-1: new high-speed USB device number 3 using ehci-platform
Sun Nov 20 16:22:10 2022 kern.info kernel: [ 528.267593] usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested
Sun Nov 20 16:22:10 2022 kern.info kernel: [ 528.571440] usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008
Sun Nov 20 16:22:11 2022 kern.info kernel: [ 528.822700] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits
Sun Nov 20 16:22:11 2022 kern.info kernel: [ 529.085907] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.4
Sun Nov 20 16:22:11 2022 kern.info kernel: [ 529.091697] ath9k_htc 1-1:1.0: FW RMW support: On
Sun Nov 20 16:22:11 2022 kern.debug kernel: [ 529.096567] ath: EEPROM regdomain: 0x809c
Sun Nov 20 16:22:11 2022 kern.debug kernel: [ 529.096579] ath: EEPROM indicates we should expect a country code
Sun Nov 20 16:22:11 2022 kern.debug kernel: [ 529.096593] ath: doing EEPROM country->regdmn map search
Sun Nov 20 16:22:11 2022 kern.debug kernel: [ 529.096606] ath: country maps to regdmn code: 0x52
Sun Nov 20 16:22:11 2022 kern.debug kernel: [ 529.096620] ath: Country alpha2 being used: CN
Sun Nov 20 16:22:11 2022 kern.debug kernel: [ 529.096632] ath: Regpair used: 0x52
Sun Nov 20 16:22:11 2022 kern.info kernel: [ 529.105041] ieee80211 phy2: Atheros AR9271 Rev:1
Sun Nov 20 16:22:11 2022 kern.info kernel: [ 529.292225] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
Sun Nov 20 16:22:11 2022 daemon.notice hostapd: wlan1: INTERFACE-ENABLED
Sun Nov 20 16:22:11 2022 daemon.err hostapd: Failed to set beacon parameters
Sun Nov 20 16:22:14 2022 authpriv.info dropbear[1714]: Exit (root): Exited normally
Sun Nov 20 16:22:22 2022 authpriv.info dropbear[1979]: Child connection from 192.168.11.172:6241
Sun Nov 20 16:22:27 2022 authpriv.notice dropbear[1979]: Password auth succeeded for 'root' from 192.168.11.172:6241
root@Router:~#

Cezary · 2022-11-20 17:33:13

Cezary
...
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2006-02-25
Posty: 116,956

Odp: Karta Wi Fi przez USB automatyczne uruchamianie

Tak wygląda to u mnie:

Thu Nov 10 14:53:13 2022 kern.info kernel: [  218.682052] usb 1-2: new high-speed USB device number 3 using xhci-mtk
Thu Nov 10 14:53:13 2022 kern.info kernel: [  218.909040] usb 1-2: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested
Thu Nov 10 14:53:13 2022 kern.info kernel: [  219.217907] usb 1-2: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008
Thu Nov 10 14:53:13 2022 kern.info kernel: [  219.468644] ath9k_htc 1-2:1.0: ath9k_htc: HTC initialized with 33 credits
Thu Nov 10 14:53:14 2022 kern.info kernel: [  219.754533] ath9k_htc 1-2:1.0: ath9k_htc: FW Version: 1.4
Thu Nov 10 14:53:14 2022 kern.info kernel: [  219.765456] ath9k_htc 1-2:1.0: FW RMW support: On
Thu Nov 10 14:53:14 2022 kern.debug kernel: [  219.775207] ath: EEPROM regdomain: 0x809c
Thu Nov 10 14:53:14 2022 kern.debug kernel: [  219.775408] ath: EEPROM indicates we should expect a country code
Thu Nov 10 14:53:14 2022 kern.debug kernel: [  219.775440] ath: doing EEPROM country->regdmn map search
Thu Nov 10 14:53:14 2022 kern.debug kernel: [  219.775468] ath: country maps to regdmn code: 0x52
Thu Nov 10 14:53:14 2022 kern.debug kernel: [  219.775486] ath: Country alpha2 being used: CN
Thu Nov 10 14:53:14 2022 kern.debug kernel: [  219.775493] ath: Regpair used: 0x52
Thu Nov 10 14:53:14 2022 kern.debug kernel: [  219.817814] ath: EEPROM regdomain: 0x8268
Thu Nov 10 14:53:14 2022 kern.debug kernel: [  219.817842] ath: EEPROM indicates we should expect a country code
Thu Nov 10 14:53:14 2022 kern.debug kernel: [  219.817853] ath: doing EEPROM country->regdmn map search
Thu Nov 10 14:53:14 2022 kern.debug kernel: [  219.817865] ath: country maps to regdmn code: 0x37
Thu Nov 10 14:53:14 2022 kern.debug kernel: [  219.817877] ath: Country alpha2 being used: PL
Thu Nov 10 14:53:14 2022 kern.debug kernel: [  219.817884] ath: Regpair used: 0x37
Thu Nov 10 14:53:14 2022 kern.debug kernel: [  219.817896] ath: regdomain 0x8268 dynamically updated by user
Thu Nov 10 14:53:14 2022 kern.info kernel: [  219.820406] ieee80211 phy3: Atheros AR9271 Rev:1
Thu Nov 10 14:53:15 2022 daemon.notice wpa_supplicant[2083]: wlan2: SME: Trying to authenticate with XX:XX:XX:XX:XX:XX (SSID='test' freq=2462 MHz)
Thu Nov 10 14:53:15 2022 kern.info kernel: [  221.587947] wlan2: authenticate with XX:XX:XX:XX:XX:XX
Thu Nov 10 14:53:16 2022 kern.info kernel: [  221.801044] wlan2: send auth to XX:XX:XX:XX:XX:XX (try 1/3)
Thu Nov 10 14:53:16 2022 daemon.notice wpa_supplicant[2083]: wlan2: Trying to associate with XX:XX:XX:XX:XX:XX (SSID='test' freq=2462 MHz)
Thu Nov 10 14:53:16 2022 kern.info kernel: [  221.829589] wlan2: authenticated
Thu Nov 10 14:53:16 2022 kern.info kernel: [  221.843433] wlan2: associate with XX:XX:XX:XX:XX:XX(try 1/3)
Thu Nov 10 14:53:16 2022 kern.info kernel: [  221.868399] wlan2: RX AssocResp from XX:XX:XX:XX:XX:XX (capab=0x431 status=0 aid=3)
Thu Nov 10 14:53:16 2022 daemon.notice netifd: Network device 'wlan2' link is up
Thu Nov 10 14:53:16 2022 daemon.notice netifd: Interface 'wan' has link connectivity
Thu Nov 10 14:53:16 2022 daemon.notice netifd: Interface 'wan' is setting up now
Thu Nov 10 14:53:16 2022 daemon.notice wpa_supplicant[2083]: wlan2: Associated with XX:XX:XX:XX:XX:XX
Thu Nov 10 14:53:16 2022 daemon.notice wpa_supplicant[2083]: wlan2: CTRL-EVENT-SUBNET-STATUS-UPDATE status=0
Thu Nov 10 14:53:16 2022 daemon.notice wpa_supplicant[2083]: wlan2: Unknown event 37
Thu Nov 10 14:53:16 2022 kern.info kernel: [  221.907945] wlan2: associated
Thu Nov 10 14:53:16 2022 daemon.notice wpa_supplicant[2083]: wlan2: WPA: Key negotiation completed with XX:XX:XX:XX:XX:XX [PTK=CCMP GTK=CCMP]
Thu Nov 10 14:53:16 2022 daemon.notice wpa_supplicant[2083]: wlan2: CTRL-EVENT-CONNECTED - Connection to XX:XX:XX:XX:XX:XX completed [id=0 id_str=]
Thu Nov 10 14:53:16 2022 kern.info kernel: [  222.013711] IPv6: ADDRCONF(NETDEV_CHANGE): wlan2: link becomes ready
Thu Nov 10 14:53:16 2022 daemon.notice wpa_supplicant[2083]: wlan2: Unknown event 37
Thu Nov 10 14:53:16 2022 daemon.notice netifd: wan (8655): udhcpc: started, v1.35.0
Thu Nov 10 14:53:16 2022 daemon.notice netifd: wan (8655): udhcpc: broadcasting discover
Thu Nov 10 14:53:16 2022 daemon.notice netifd: wan (8655): udhcpc: broadcasting select for 10.1.1.150, server 10.1.1.1
Thu Nov 10 14:53:16 2022 daemon.notice netifd: wan (8655): udhcpc: lease of 10.1.1.150 obtained from 10.1.1.1, lease time 7200
Thu Nov 10 14:53:16 2022 daemon.notice netifd: Interface 'wan' is now up
Thu Nov 10 14:53:16 2022 daemon.info dnsmasq[1]: reading /tmp/resolv.conf.d/resolv.conf.auto

Przy takim networku:

config interface 'wan'
    option proto 'dhcp'

i wireless

config wifi-device 'radio2'
    option type 'mac80211'
    option path 'platform/1e1c0000.xhci/usb1/1-2/1-2:1.0'
    option channel '1'
    option band '2g'
    option htmode 'HT20'
    option disabled '0'
    option country 'PL'

config wifi-iface 'default_radio2'
    option device 'radio2'
    option network 'wan'
    option mode 'sta'
    option ssid 'test'
    option encryption 'psk2'
    option key <key>

Router r6220, karta tplinka TL-WN722N v1. Działa za każdym razem, podnosi się samodzielnie po restarcie lub włożeniu karty. Moje OpenWrt 22.03.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Focus · 2022-11-20 17:53:59

Focus
Użytkownik
Nieaktywny

Zarejestrowany: 2020-10-20
Posty: 973

Odp: Karta Wi Fi przez USB automatyczne uruchamianie

U mnie TL-MR3420v2 jako AP, a karta to TL-WN422G.

network

config interface 'loopback'
option ifname 'lo'
option proto 'static'
option ipaddr '127.0.0.1'
option netmask '255.0.0.0'
config globals 'globals'
option ula_prefix 'fd14:9048:8ef9::/48'
config interface 'lan'
option type 'bridge'
option ifname 'eth1'
option proto 'static'
option netmask '255.255.255.0'
option ip6assign '60'
option ipaddr '192.168.11.1'
config interface 'wan'
option ifname 'eth0'
option proto 'dhcp'
config interface 'wan6'
option ifname 'eth0'
option proto 'dhcpv6'
config switch
option name 'switch0'
option reset '1'
option enable_vlan '1'
config switch_vlan
option device 'switch0'
option vlan '1'
option ports '0 1 2 3 4'
config interface 'wwan'
option proto 'dhcp'

wireless

config wifi-device 'radio0'
option type 'mac80211'
option channel '11'
option hwmode '11g'
option path 'platform/ar934x_wmac'
option country 'PL'
option htmode 'HT20'
option noscan '1'
config wifi-iface 'net2'
option key '<key>'
option ssid 'Wi-Fi'
option bssid 'a4:2b:8c:2e:40:9f'
option device 'radio0'
option mode 'sta'
option network 'wwan'
option encryption 'psk2'
config wifi-iface 'default_radio0'
option device 'radio0'
option network 'lan'
option mode 'ap'
option encryption 'psk2'
option key '<key>'
option macaddr 'a4:2b:8c:2a:40:9f'
option isolate '1'
option ssid 'Wi-Fi'
config wifi-device 'radio1'
option type 'mac80211'
option channel '8'
option hwmode '11g'
option path 'platform/ehci-platform/usb1/1-1/1-1:1.0'
option htmode 'HT20'
option disabled '0'
option country 'PL'
config wifi-iface 'default_radio1'
option device 'radio1'
option network 'lan'
option mode 'ap'
option ssid 'Borys'
option encryption 'psk2'
option key '<key>'
option macaddr 'a4:2b:8c:2c:40:9f'
option isolate '1'

Wyżej w poprzednim poście edytowałem i dokleiłem logi jak wygląda to w logread z włożoną działającą kartą i po jej ponownym włożeniu.

Cezary · 2022-11-20 18:07:37

Cezary
...
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2006-02-25
Posty: 116,956

Odp: Karta Wi Fi przez USB automatyczne uruchamianie

Masz adres powinieneś mieć bo masz taki sam jak pierwsze radia. A tak poza tym wygląda sensownie...

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Focus · 2022-11-20 19:27:35

Focus
Użytkownik
Nieaktywny

Zarejestrowany: 2020-10-20
Posty: 973

Odp: Karta Wi Fi przez USB automatyczne uruchamianie

Zauważyłem, że:
1. Jeżeli uruchomię router z już włożoną kartą wi fi usb to radio na tej karcie uruchamia się (świeci się dioda na karcie)
2. Jeżeli uruchomię najpierw router, a następnie włożę kartę wi fi do usb to radio tej karty nie uruchamia się (nie świeci dioda na karcie).

Dla obu przypadków jeżeli w putty wydam polecenie "wifi" to radio się natychmiast uruchamia i pojawia się sieć z tego radia.

Może trzeba to jakoś opóźnić włączenie tego radia? Zgaduję, bo nie wiem. Jak już to w /etc/rc.local , czy jeszcze gdzieś?

Cezary · 2022-11-20 19:30:07

Cezary
...
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2006-02-25
Posty: 116,956

Odp: Karta Wi Fi przez USB automatyczne uruchamianie

Cóż, nie działa u Ciebie to to obejdź - w /etc/hotsplug.d/usb zrób sobie skrypt, który na pojawienie się odpowiedniego interfejsu zróbi wfi po prostu. Jak to zrobisz masz opisane np. tu: https://eko.one.pl/?p=openwrt-linkidoportowszeregowych

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Focus · 2022-11-20 22:00:06

Focus
Użytkownik
Nieaktywny

Zarejestrowany: 2020-10-20
Posty: 973

Odp: Karta Wi Fi przez USB automatyczne uruchamianie

Mam pytanie co do skryptu.

Mam DEVPATH=/devices/platform/ehci-platform/usb1/1-1/1-1:1.0
Tam gdzie jest $DEVPATH/ttyUSB mam wpisać całą linijkę z DEVPATH czyli /devices/platform/ehci-platform/usb1/1-1/1-1:1.0, czy tylko usb1 czy może jeszcze jakoś inaczej?

Cezary · 2022-11-20 22:06:11

Cezary
...
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2006-02-25
Posty: 116,956

Odp: Karta Wi Fi przez USB automatyczne uruchamianie

Co właściwie robisz? Sprawdź czy PRODUCT odpowiada karcie którą masz, nie musisz sprawdzać gdzie jest włożona przez badanie DEVPATH. Zostaw DEVPATH w spokoju.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Focus · 2022-11-20 22:19:51

Focus
Użytkownik
Nieaktywny

Zarejestrowany: 2020-10-20
Posty: 973

Odp: Karta Wi Fi przez USB automatyczne uruchamianie

Robię jak we wskazanym linku czyli:
w

/etc/hotplug.d/usb

wpisuję

#!/bin/sh
echo "----" > /tmp/plik.txt
env >> /tmp/plik.txt

otrzymuję

----
USER=root
ACTION=add
SHLVL=2
HOME=/
SEQNUM=532
HOTPLUG_TYPE=usb
DEVPATH=/devices/platform/ehci-platform/usb1/1-1/1-1:1.0
DEVICENAME=1-1:1.0
LOGNAME=root
TERM=linux
SUBSYSTEM=usb
board=TL-MR3420-v2
PATH=/usr/sbin:/usr/bin:/sbin:/bin
MODALIAS=usb:v0CF3p1006d0108dcFFdscFFdpFFicFFisc00ip00in00
TYPE=255/255/255
INTERFACE=255/0/0
PRODUCT=cf3/1006/108
PWD=/
DEVTYPE=usb_interface

Gdzie i jak mam sprawdzić czy PRODUCT odpowiada karcie?

Cezary · 2022-11-20 22:32:45

Cezary
...
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2006-02-25
Posty: 116,956

Odp: Karta Wi Fi przez USB automatyczne uruchamianie

#!/bin/sh
if [ "$PRODUCT" = "cf3/1006/108" ]; then
  sleep 5 # zeby sie wszystko wykrylo
  logger "Ehhh, mam karte, uruchamiam wifi"
  wifi
fi

W skrypcie w katalogu /etc/hotplug.d/usb

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Focus · 2022-11-20 23:13:18

Focus
Użytkownik
Nieaktywny

Zarejestrowany: 2020-10-20
Posty: 973

Odp: Karta Wi Fi przez USB automatyczne uruchamianie

Teraz działa znakomicie.
Byłem przekonany, że chodzi o DEVPATH/ttyUSB, a tu zupełnie co innego i to dosłownie kilka linijek kodu razem z komentarzem aby było widać w logread co i kiedy.
Dziękuję Cezary za pomoc.
Moje pytania na chwilę obecną co do tematu się wyczerpały.

FAQ o OpenWrt | Sprzedam różne routery | Oddam

Karta Wi Fi przez USB automatyczne uruchamianie

Posty: 17

1 Temat przez Focus 2022-11-20 14:49:16

Temat: Karta Wi Fi przez USB automatyczne uruchamianie

2 Odpowiedź przez Cezary 2022-11-20 14:52:21

Odp: Karta Wi Fi przez USB automatyczne uruchamianie

3 Odpowiedź przez Focus 2022-11-20 14:58:44

Odp: Karta Wi Fi przez USB automatyczne uruchamianie

4 Odpowiedź przez Cezary 2022-11-20 15:07:19

Odp: Karta Wi Fi przez USB automatyczne uruchamianie

5 Odpowiedź przez Focus 2022-11-20 15:46:04

Odp: Karta Wi Fi przez USB automatyczne uruchamianie

6 Odpowiedź przez Cezary 2022-11-20 15:59:05

Odp: Karta Wi Fi przez USB automatyczne uruchamianie

7 Odpowiedź przez Focus 2022-11-20 16:59:01 (edytowany przez Focus 2022-11-20 17:35:33)

Odp: Karta Wi Fi przez USB automatyczne uruchamianie

8 Odpowiedź przez Cezary 2022-11-20 17:33:13

Odp: Karta Wi Fi przez USB automatyczne uruchamianie

9 Odpowiedź przez Focus 2022-11-20 17:53:59

Odp: Karta Wi Fi przez USB automatyczne uruchamianie

10 Odpowiedź przez Cezary 2022-11-20 18:07:37

Odp: Karta Wi Fi przez USB automatyczne uruchamianie

11 Odpowiedź przez Focus 2022-11-20 19:27:35

Odp: Karta Wi Fi przez USB automatyczne uruchamianie

12 Odpowiedź przez Cezary 2022-11-20 19:30:07

Odp: Karta Wi Fi przez USB automatyczne uruchamianie

13 Odpowiedź przez Focus 2022-11-20 22:00:06

Odp: Karta Wi Fi przez USB automatyczne uruchamianie

14 Odpowiedź przez Cezary 2022-11-20 22:06:11

Odp: Karta Wi Fi przez USB automatyczne uruchamianie

15 Odpowiedź przez Focus 2022-11-20 22:19:51 (edytowany przez Focus 2022-11-20 22:20:32)

Odp: Karta Wi Fi przez USB automatyczne uruchamianie

16 Odpowiedź przez Cezary 2022-11-20 22:32:45

Odp: Karta Wi Fi przez USB automatyczne uruchamianie

17 Odpowiedź przez Focus 2022-11-20 23:13:18

Odp: Karta Wi Fi przez USB automatyczne uruchamianie

Posty: 17