351 Odpowiedź przez stich86

  • Zarejestrowany: 2022-05-24
  • Posty: 392

Odp: ZTE MF289F - Porting OpenWRT

MiG25 napisał/a:

exacly , everybody expect , that wan will be WAN/LAN1...

How to solve it?
I’ve to rename eth0 to 1 and viceversa…

352 Odpowiedź przez MiG25

  • MiG25
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2014-07-23
  • Posty: 3,796

Odp: ZTE MF289F - Porting OpenWRT

That is a question. If you want to keep eth0 to lan1 and eth1 to lan2  then maybe only in config/network  (bridge eth1 with lan and make eth0 as WAN )?

353 Odpowiedź przez stich86

  • Zarejestrowany: 2022-05-24
  • Posty: 392

Odp: ZTE MF289F - Porting OpenWRT

MiG25 napisał/a:

That is a question. If you want to keep eth0 to lan1 and eth1 to lan2  then maybe only in config/network  (bridge eth1 with lan and make eth0 as WAN )?

yes I know, but we are talking about vallina OpenWRT.
Custom build using config/network can be easly done, like my build.. but on vanilla OpenWRT I need to understand how to do it

354 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,025

Odp: ZTE MF289F - Porting OpenWRT

see: https://github.com/openwrt/openwrt/blob … twork#L165

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

355 Odpowiedź przez MiG25

  • MiG25
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2014-07-23
  • Posty: 3,796

Odp: ZTE MF289F - Porting OpenWRT

Next thing , reboot probably not rebooting modem (leds are lighting all the time)  ,also on PCB is not blinking . I belive there where some work on that  recently , since i don't remember such behaviour from your builds.

egarding wifi , as expected , there is still issue with channel 132 (now not starting at all).

356 Odpowiedź przez MiG25 (edytowany przez MiG25 2022-09-27 11:56:27)

  • MiG25
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2014-07-23
  • Posty: 3,796

Odp: ZTE MF289F - Porting OpenWRT

reboot for sure is not rebooting modem ( so i.e. will not bring connection after sim exchange). At the same time AT+CFUN=1,1 reboting also mf289f...

Also i'm pritty sure , that status- on pcb blue led was blinking during startup ( like on MF286D) , now blinks maybe once or two times and then it is on all the time...

here is a log from boot :

Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset),  D - Delta,  S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.1.1-00126
S - IMAGE_VARIANT_STRING=DAABANAZA
S - OEM_IMAGE_VERSION_STRING=CRM
S - Boot Config, 0x00000021
S - Reset status Config, 0x00000010
S - Core 0 Frequency, 0 MHz
B -       261 - PBL, Start
B -      1339 - bootable_media_detect_entry, Start
B -      1679 - bootable_media_detect_success, Start
B -      1693 - elf_loader_entry, Start
B -      5082 - auth_hash_seg_entry, Start
B -      7231 - auth_hash_seg_exit, Start
B -    579481 - elf_segs_hash_verify_entry, Start
B -    697499 - PBL, End
B -    697523 - SBL1, Start
B -    788386 - pm_device_init, Start
D -         7 - pm_device_init, Delta
B -    789850 - boot_flash_init, Start
D -     52866 - boot_flash_init, Delta
B -    846861 - boot_config_data_table_init, Start
D -      3840 - boot_config_data_table_init, Delta - (419 Bytes)
B -    854344 - clock_init, Start
D -      7564 - clock_init, Delta
B -    865949 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:0,Subtype:1
B -    869362 - sbl1_ddr_set_params, Start
B -    874459 - cpr_init, Start
D -         2 - cpr_init, Delta
B -    878841 - Pre_DDR_clock_init, Start
D -         4 - Pre_DDR_clock_init, Delta
D -     13174 - sbl1_ddr_set_params, Delta
B -    892154 - pm_driver_init, Start
D -         2 - pm_driver_init, Delta
B -    962427 - sbl1_wait_for_ddr_training, Start
D -        27 - sbl1_wait_for_ddr_training, Delta
B -    977830 - Image Load, Start
D -    153048 - QSEE Image Loaded, Delta - (299560 Bytes)
B -   1131306 - Image Load, Start
D -      1444 - SEC Image Loaded, Delta - (2048 Bytes)
B -   1141580 - Image Load, Start
D -    231178 - APPSBL Image Loaded, Delta - (473243 Bytes)
B -   1373155 - QSEE Execution, Start
D -        60 - QSEE Execution, Delta
B -   1379341 - SBL1, End
D -    683924 - SBL1, Delta
S - Flash Throughput, 2011 KB/s  (775270 Bytes,  385486 us)
S - DDR Frequency, 672 MHz


U-Boot 2012.07 [Chaos Calmer 15.05.1,IPQ4019.ILQ.6.1.0.r2-00006-P-1] (May 27 2021 - 04:33:40)

smem ram ptable found: ver: 1 len: 3
DRAM:  256 MiB
machid : 0x8010001
NAND:  spi_nand: spi_nand_flash_probe SF NAND ID ff:c8:d1:c8
SF: Detected GD5F1GQ4XB with page size 2 KiB, total 128 MiB
SF: Detected GD25Q16 with page size 4 KiB, total 2 MiB
ipq_spi: page_size: 0x100, sector_size: 0x1000, size: 0x200000
130 MiB
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
machid: 8010001
flash_type: 0
Uaztemain: enter into !
ZTE_InitFotaFlashPara: nand_curr_device=1
zte_getHandOffState: read data=0xff from 0x0
Press ESC to abort autoboot in 0 seconds
Creating 1 MTD partitions on "nand1":
0x000001800000-0x000003500000 : "mtd=0"
UBI: attaching mtd2 to ubi0
UBI: physical eraseblock size:   131072 bytes (128 KiB)
UBI: logical eraseblock size:    126976 bytes
UBI: smallest flash I/O unit:    2048
UBI: VID header offset:          2048 (aligned 2048)
UBI: data offset:                4096
UBI: attached mtd2 to ubi0
UBI: MTD device name:            "mtd=0"
UBI: MTD device size:            29 MiB
UBI: number of good PEBs:        232
UBI: number of bad PEBs:         0
UBI: max. allowed volumes:       128
UBI: wear-leveling threshold:    4096
UBI: number of internal volumes: 1
UBI: number of user volumes:     3
UBI: available PEBs:             18
UBI: total number of reserved PEBs: 214
UBI: number of PEBs reserved for bad PEB handling: 2
UBI: max/mean erase counter: 8/5
Read 0 bytes from volume kernel to 84000000
No size specified -> Using max size (3174400)
## Booting kernel from FIT Image at 84000000 ...
   Using 'config@ap.dk04.1-c1' configuration
   Trying 'kernel-1' kernel subimage
     Description:  ARM OpenWrt Linux-5.15.69
     Type:         Kernel Image
     Compression:  uncompressed
     Data Start:   0x840000e4
     Data Size:    3147848 Bytes = 3 MiB
     Architecture: ARM
     OS:           Linux
     Load Address: 0x80208000
     Entry Point:  0x80208000
     Hash algo:    crc32
     Hash value:   55454943
     Hash algo:    sha1
     Hash value:   1b1dd4d45b3f65a1c7c19253dfa2acbc1b991d15
   Verifying Hash Integrity ... crc32+ sha1+ OK
## Flattened Device Tree from FIT Image at 84000000
   Using 'config@ap.dk04.1-c1' configuration
   Trying 'fdt-1' FDT blob subimage
     Description:  ARM OpenWrt zte_mf289f device tree blob
     Type:         Flat Device Tree
     Compression:  uncompressed
     Data Start:   0x84300a60
     Data Size:    18771 Bytes = 18.3 KiB
     Architecture: ARM
     Hash algo:    crc32
     Hash value:   18e41883
     Hash algo:    sha1
     Hash value:   97b9d5341ff92994b8e4ec7d2f8e2fdfb5889db6
   Verifying Hash Integrity ... crc32+ sha1+ OK
   Booting using the fdt blob at 0x84300a60
   Loading Kernel Image ... OK
OK
   Loading Device Tree to 86ff8000, end 86fff952 ... OK
ipq: fdt fixup unable to find compatible node
Device nand0 not found!
invalid mtd device 'nand1'
eth0 MAC Address from ART is not valid
eth1 MAC Address from ART is not valid
Using machid 0x8010001 from environment

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 5.15.69 (builder@buildhost) (arm-openwrt-linux-muslgnueabi-gcc (OpenWrt GCC 11.3.0 r20746-a67f484e67) 11.3.0, GNU ld (GNU Binutils) 2.37) #0 SMP Sat Sep 24 21:53:53 2022
[    0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt: Machine model: ZTE MF289F
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000080000000-0x000000008fffffff]
[    0.000000]   HighMem  empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000080000000-0x0000000087dfffff]
[    0.000000]   node   0: [mem 0x0000000087e00000-0x0000000087ffffff]
[    0.000000]   node   0: [mem 0x0000000088000000-0x000000008fffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000008fffffff]
[    0.000000] percpu: Embedded 12 pages/cpu s16652 r8192 d24308 u49152
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 64960
[    0.000000] Kernel command line: ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashfs rootwait root=/dev/ubiblock0_1
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 246180K/262144K available (6763K kernel code, 610K rwdata, 1688K rodata, 1024K init, 248K bss, 15964K reserved, 0K cma-reserved, 0K highmem)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] rcu: Hierarchical RCU implementation.
[    0.000000]  Tracing variant of Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] arch_timer: cp15 timer(s) running at 48.00MHz (virt).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xb11fd3bfb, max_idle_ns: 440795203732 ns
[    0.000001] sched_clock: 56 bits at 48MHz, resolution 20ns, wraps every 4398046511096ns
[    0.000024] Switching to timer-based delay loop, resolution 20ns
[    0.000327] Calibrating delay loop (skipped), value calculated using timer frequency.. 96.00 BogoMIPS (lpj=480000)
[    0.000356] pid_max: default: 32768 minimum: 301
[    0.000615] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.000646] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.001673] CPU: Testing write buffer coherency: ok
[    0.002040] qcom_scm: convention: smc legacy
[    0.003044] Setting up static identity map for 0x80300000 - 0x8030003c
[    0.003212] rcu: Hierarchical SRCU implementation.
[    0.003468] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build
[    0.003806] smp: Bringing up secondary CPUs ...
[    0.007093] smp: Brought up 1 node, 4 CPUs
[    0.007129] SMP: Total of 4 processors activated (384.00 BogoMIPS).
[    0.007144] CPU: All CPU(s) started in SVC mode.
[    0.012655] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[    0.012816] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.012852] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[    0.013099] pinctrl core: initialized pinctrl subsystem
[    0.014770] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[    0.015160] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.016252] thermal_sys: Registered thermal governor 'step_wise'
[    0.016672] cpuidle: using governor ladder
[    0.016734] cpuidle: using governor menu
[    0.044002] cryptd: max_cpu_qlen set to 1000
[    0.048086] usbcore: registered new interface driver usbfs
[    0.048163] usbcore: registered new interface driver hub
[    0.048226] usbcore: registered new device driver usb
[    0.048276] pps_core: LinuxPPS API ver. 1 registered
[    0.048290] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.048320] PTP clock support registered
[    0.050398] clocksource: Switched to clocksource arch_sys_counter
[    0.051317] NET: Registered PF_INET protocol family
[    0.051542] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear)
[    0.052354] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[    0.052411] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.052434] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear)
[    0.052478] TCP bind hash table entries: 2048 (order: 2, 16384 bytes, linear)
[    0.052534] TCP: Hash tables configured (established 2048 bind 2048)
[    0.052651] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.052699] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.052971] NET: Registered PF_UNIX/PF_LOCAL protocol family
[    0.053029] PCI: CLS 0 bytes, default 64
[    0.055243] workingset: timestamp_bits=14 max_order=16 bucket_order=2
[    0.060198] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.060230] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.192623] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
[    0.195378] qcom-pcie 40000000.pci: host bridge /soc/pci@40000000 ranges:
[    0.195457] qcom-pcie 40000000.pci:       IO 0x0040200000..0x00402fffff -> 0x0040200000
[    0.195495] qcom-pcie 40000000.pci:      MEM 0x0040300000..0x0040ffffff -> 0x0040300000
[    0.371986] qcom-pcie 40000000.pci: iATU unroll: disabled
[    0.372020] qcom-pcie 40000000.pci: Detected iATU regions: 32 outbound, 8 inbound
[    1.372315] qcom-pcie 40000000.pci: Phy link never came up
[    1.372478] qcom-pcie 40000000.pci: PCI host bridge to bus 0000:00
[    1.372500] pci_bus 0000:00: root bus resource [bus 00-ff]
[    1.372527] pci_bus 0000:00: root bus resource [io  0x0000-0xfffff] (bus address [0x40200000-0x402fffff])
[    1.372547] pci_bus 0000:00: root bus resource [mem 0x40300000-0x40ffffff]
[    1.372603] pci 0000:00:00.0: [17cb:1001] type 01 class 0x060400
[    1.372640] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x00000fff]
[    1.372717] pci 0000:00:00.0: PME# supported from D0 D3hot
[    1.374352] PCI: bus0: Fast back to back transfers disabled
[    1.375820] PCI: bus1: Fast back to back transfers enabled
[    1.375869] pci 0000:00:00.0: BAR 0: assigned [mem 0x40300000-0x40300fff]
[    1.375899] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[    1.378778] pcieport 0000:00:00.0: AER: enabled with IRQ 103
[    1.380965] bam-dma-engine 8e04000.dma: num-channels unspecified in dt
[    1.380997] bam-dma-engine 8e04000.dma: num-ees unspecified in dt
[    1.382359] tcsr 1949000.tcsr: setting wifi_glb_cfg = 41000000
[    1.382469] tcsr 194b000.tcsr: setting usb hs phy mode select = e700e7
[    1.382564] tcsr 1953000.ess_tcsr: setting ess interface select = 0
[    1.382661] tcsr 1957000.tcsr: setting wifi_noc_memtype_m0_m2 = 2222222
[    1.382991] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    1.384772] msm_serial 78af000.serial: msm_serial: detected port #0
[    1.384825] msm_serial 78af000.serial: uartclk = 1843200
[    1.384883] 78af000.serial: ttyMSM0 at MMIO 0x78af000 (irq = 33, base_baud = 115200) is a MSM
[    1.384921] msm_serial: console setup on port #0
[    2.058978] printk: console [ttyMSM0] enabled
[    2.064136] msm_serial: driver initialized
[    2.073254] loop: module loaded
[    2.074317] spi_qup 78b5000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64
[    2.076903] spi-nor spi0.0: gd25q16 (2048 Kbytes)
[    2.082608] 8 fixed-partitions partitions found on MTD device spi0.0
[    2.087112] Creating 8 MTD partitions on "spi0.0":
[    2.093550] 0x000000000000-0x000000040000 : "0:SBL1"
[    2.098712] 0x000000040000-0x000000060000 : "0:MIBIB"
[    2.103782] 0x000000060000-0x0000000c0000 : "0:QSEE"
[    2.108736] 0x0000000c0000-0x0000000d0000 : "0:CDT"
[    2.113765] 0x0000000d0000-0x0000000e0000 : "0:DDRPARAMS"
[    2.118301] 0x0000000e0000-0x0000000f0000 : "0:APPSBLENV"
[    2.123911] 0x0000000f0000-0x0000001b0000 : "0:APPSBL"
[    2.129243] 0x0000001b0000-0x000000200000 : "0:reserved1"
[    2.137890] spi-nand spi0.1: GigaDevice SPI NAND was found.
[    2.139277] spi-nand spi0.1: 128 MiB, block size: 128 KiB, page size: 2048, OOB size: 128
[    2.145184] 12 fixed-partitions partitions found on MTD device spi0.1
[    2.153053] OF: Bad cell count for /soc/spi@78b5000/spi-nand@1/partitions
[    2.159436] OF: Bad cell count for /soc/spi@78b5000/spi-nand@1/partitions
[    2.166624] OF: Bad cell count for /soc/spi@78b5000/spi-nand@1/partitions
[    2.173006] OF: Bad cell count for /soc/spi@78b5000/spi-nand@1/partitions
[    2.180137] Creating 12 MTD partitions on "spi0.1":
[    2.186524] 0x000000000000-0x0000000a0000 : "fota-flag"
[    2.193900] 0x0000000a0000-0x000000120000 : "ART"
[    2.198635] 0x000000120000-0x0000001a0000 : "mac"
[    2.203623] 0x0000001a0000-0x000000260000 : "reserved2"
[    2.208976] 0x000000260000-0x000000660000 : "cfg-param"
[    2.224785] 0x000000660000-0x000000a60000 : "log"
[    2.238557] 0x000000a60000-0x000000b00000 : "oops"
[    2.241221] 0x000000b00000-0x000001000000 : "reserved3"
[    2.259244] 0x000001000000-0x000001800000 : "web"
[    2.286138] 0x000001800000-0x000003500000 : "rootfs"
[    2.381742] mtd: device 17 (rootfs) set to be root filesystem
[    2.383157] mtdsplit: no squashfs found in "rootfs"
[    2.386499] 0x000003500000-0x000004e00000 : "data"
[    2.473800] 0x000004e00000-0x000008000000 : "fota"
[    2.688219] ESS reset ok!
[    2.762510] ESS reset ok!
[    3.084029] PHY 0 single test PSGMII issue happen!
[    3.149664] PHY 1 single test PSGMII issue happen!
[    3.215317] PHY 2 single test PSGMII issue happen!
[    3.280992] PHY 3 single test PSGMII issue happen!
[    3.346647] PHY 4 single test PSGMII issue happen!
[    3.413052] PHY0 test see issue!
[    3.417544] PHY1 test see issue!
[    3.422020] PHY2 test see issue!
[    3.426504] PHY3 test see issue!
[    3.430991] PHY4 test see issue!
[    3.505263] ESS reset ok!
[    4.265475] i2c_dev: i2c /dev entries driver
[    4.267324] sdhci: Secure Digital Host Controller Interface driver
[    4.268826] sdhci: Copyright(c) Pierre Ossman
[    4.274886] sdhci-pltfm: SDHCI platform and OF driver helper
[    4.283090] NET: Registered PF_INET6 protocol family
[    4.286589] Segment Routing with IPv6
[    4.289950] In-situ OAM (IOAM) with IPv6
[    4.293623] NET: Registered PF_PACKET protocol family
[    4.297543] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    4.302466] 8021q: 802.1Q VLAN Support v1.8
[    4.315582] Registering SWP/SWPB emulation handler
[    4.329408] ubi0: attaching mtd17
[    5.018649] ubi0: scanning is finished
[    5.055445] ubi0: attached mtd17 (name "rootfs", size 29 MiB)
[    5.055562] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    5.060257] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    5.067126] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[    5.073978] ubi0: good PEBs: 232, bad PEBs: 0, corrupted PEBs: 0
[    5.080713] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
[    5.086907] ubi0: max/mean erase counter: 8/5, WL threshold: 4096, image sequence number: 3329320032
[    5.093997] ubi0: available PEBs: 0, total reserved PEBs: 232, PEBs reserved for bad PEB handling: 20
[    5.103342] ubi0: background thread "ubi_bgt0d" started, PID 125
[ ▒[    5.138476] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[    5.141327] Freeing unused kernel image (initmem) memory: 1024K
[    5.184171] Run /sbin/init as init process
[    6.388022] init: Console is alive
[    6.388339] init: - watchdog -
[    6.423430] random: crng init done
[    8.220563] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    8.635756] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[    8.635935] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[    8.640519] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f665 hci version 0x100 quirks 0x0000002002010010
[    8.647830] xhci-hcd xhci-hcd.0.auto: irq 106, io mem 0x08a00000
[    8.657359] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[    8.663420] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[    8.668685] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
[    8.676934] hub 1-0:1.0: USB hub found
[    8.685456] hub 1-0:1.0: 1 port detected
[    8.687019] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[    8.691225] hub 2-0:1.0: USB hub found
[    8.698747] hub 2-0:1.0: 1 port detected
[    8.702762] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[    8.706368] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
[    8.711913] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f665 hci version 0x100 quirks 0x0000002002010010
[    8.719261] xhci-hcd xhci-hcd.1.auto: irq 107, io mem 0x06000000
[    8.728799] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[    8.734871] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
[    8.740125] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed
[    8.749575] hub 3-0:1.0: USB hub found
[    8.754362] hub 3-0:1.0: 1 port detected
[    8.758439] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[    8.762648] hub 4-0:1.0: USB hub found
[    8.770187] hub 4-0:1.0: config failed, hub doesn't have any ports! (err -19)
[    8.776058] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    8.781982] init: - preinit -
[    9.821411] usb 2-1: new SuperSpeed USB device number 2 using xhci-hcd
[   11.001832] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[   13.446451] UBIFS (ubi0:2): Mounting in unauthenticated mode
[   13.446709] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" started, PID 232
[   13.623025] UBIFS (ubi0:2): recovery needed
[   13.999904] UBIFS (ubi0:2): recovery completed
[   14.000491] UBIFS (ubi0:2): UBIFS: mounted UBI device 0, volume 2, name "rootfs_data"
[   14.003360] UBIFS (ubi0:2): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[   14.011358] UBIFS (ubi0:2): FS size: 17776640 bytes (16 MiB, 140 LEBs), max 150 LEBs, journal size 1015809 bytes (0 MiB, 7 LEBs)
[   14.021218] UBIFS (ubi0:2): reserved for root: 839634 bytes (819 KiB)
[   14.032831] UBIFS (ubi0:2): media format: w5/r0 (latest is w5/r0), UUID D56679E6-0054-41CD-9A20-A2BDAEF4DE9F, small LPT model
[   14.078167] mount_root: switching to ubifs overlay
[   14.128827] urandom-seed: Seeding with /etc/urandom.seed
[   14.515642] procd: - early -
[   14.516212] procd: - watchdog -
[   15.189830] procd: - watchdog -
[   15.380533] procd: - ubus -
[   15.808062] procd: - init -
Please press Enter to activate this console.
[   17.089063] kmodloader: loading kernel modules from /etc/modules.d/*
[   17.164683] urngd: v1.0.2 started.
[   17.235389] usbcore: registered new interface driver cdc_wdm
[   17.236159] Loading modules backported from Linux version v5.15.58-0-g7d8048d4e064
[   17.240136] Backport generated by backports.git v5.15.58-1-0-g42a95ce7
[   17.259920] usbcore: registered new interface driver usbserial_generic
[   17.260025] usbserial: USB Serial support registered for generic
[   17.335610] PPP generic driver version 2.4.2
[   17.360504] NET: Registered PF_PPPOX protocol family
[   17.381823] qmi_wwan 2-1:1.3: cdc-wdm0: USB WDM device
[   17.383821] qmi_wwan 2-1:1.3 wwan0: register 'qmi_wwan' at usb-xhci-hcd.0.auto-1, WWAN/QMI device, 96:32:b1:3f:f2:7d
[   17.386189] usbcore: registered new interface driver qmi_wwan
[   19.004731] ath10k_ahb a000000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003b00ff sub 0000:0000
[   19.004802] ath10k_ahb a000000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[   19.016625] ath10k_ahb a000000.wifi: firmware ver 10.4b-ct-4019-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 6b2b5c5b
[   19.076691] ath10k_ahb a000000.wifi: Loading BDF type 0
[   19.077332] ath10k_ahb a000000.wifi: board_file api 2 bmi_id 0:20 crc32 1323eb04
[   20.376298] ath10k_ahb a000000.wifi: 10.4 wmi init: vdevs: 16  peers: 48  tid: 96
[   20.376371] ath10k_ahb a000000.wifi: msdu-desc: 2500  skid: 32
[   20.425914] ath10k_ahb a000000.wifi: wmi print 'P 48/48 V 16 K 144 PH 176 T 186  msdu-desc: 2500  sw-crypt: 0 ct-sta: 0'
[   20.427615] ath10k_ahb a000000.wifi: wmi print 'free: 53252 iram: 13432 sram: 35752'
[   20.570999] ath10k_ahb a000000.wifi: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-nvmem max-sta 32 raw 0 hwcrypto 1
[   22.016137] ath10k_ahb a800000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003b00ff sub 0000:0000
[   22.016207] ath10k_ahb a800000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[   22.037649] ath10k_ahb a800000.wifi: firmware ver 10.4b-ct-4019-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 6b2b5c5b
[   22.091585] ath10k_ahb a800000.wifi: Loading BDF type 0
[   22.091846] ath10k_ahb a800000.wifi: board_file api 2 bmi_id 0:21 crc32 1323eb04
[   23.391867] ath10k_ahb a800000.wifi: 10.4 wmi init: vdevs: 16  peers: 48  tid: 96
[   23.391939] ath10k_ahb a800000.wifi: msdu-desc: 2500  skid: 32
[   23.439102] ath10k_ahb a800000.wifi: wmi print 'P 48/48 V 16 K 144 PH 176 T 186  msdu-desc: 2500  sw-crypt: 0 ct-sta: 0'
[   23.440837] ath10k_ahb a800000.wifi: wmi print 'free: 53252 iram: 13432 sram: 35752'
[   23.578872] ath10k_ahb a800000.wifi: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-nvmem max-sta 32 raw 0 hwcrypto 1
[   23.751018] usbcore: registered new interface driver option
[   23.751136] usbserial: USB Serial support registered for GSM modem (1-port)
[   23.755898] option 2-1:1.0: GSM modem (1-port) converter detected
[   23.762778] usb 2-1: GSM modem (1-port) converter now attached to ttyUSB0
[   23.769052] option 2-1:1.1: GSM modem (1-port) converter detected
[   23.775773] usb 2-1: GSM modem (1-port) converter now attached to ttyUSB1
[   23.781994] option 2-1:1.2: GSM modem (1-port) converter detected
[   23.788594] usb 2-1: GSM modem (1-port) converter now attached to ttyUSB2
[   23.797692] kmodloader: done loading kernel modules from /etc/modules.d/*
[   32.846583] br-lan: port 1(eth0) entered blocking state
[   32.846645] br-lan: port 1(eth0) entered disabled state
[   32.851146] device eth0 entered promiscuous mode
[   33.910502] br-lan: port 1(eth0) entered blocking state
[   33.910593] br-lan: port 1(eth0) entered forwarding state
[   33.915099] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   35.531478] ath10k_ahb a000000.wifi: 10.4 wmi init: vdevs: 16  peers: 48  tid: 96
[   35.531548] ath10k_ahb a000000.wifi: msdu-desc: 2500  skid: 32
[   35.580454] ath10k_ahb a000000.wifi: wmi print 'P 48/48 V 16 K 144 PH 176 T 186  msdu-desc: 2500  sw-crypt: 0 ct-sta: 0'
[   35.581407] ath10k_ahb a000000.wifi: wmi print 'free: 53252 iram: 13432 sram: 35752'
[   35.912235] ath10k_ahb a000000.wifi: rts threshold -1
[   35.912689] ath10k_ahb a000000.wifi: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4
[   35.921726] br-lan: port 2(wlan0) entered blocking state
[   35.927238] br-lan: port 2(wlan0) entered disabled state
[   35.933179] device wlan0 entered promiscuous mode
[   36.034357] ath10k_ahb a000000.wifi: NOTE:  Firmware DBGLOG output disabled in debug_mask: 0x10000000
[   36.262904] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   36.265216] br-lan: port 2(wlan0) entered blocking state
[   36.268766] br-lan: port 2(wlan0) entered forwarding state
[   37.935367] ath10k_ahb a800000.wifi: 10.4 wmi init: vdevs: 16  peers: 48  tid: 96
[   37.935454] ath10k_ahb a800000.wifi: msdu-desc: 2500  skid: 32
[   37.982674] ath10k_ahb a800000.wifi: wmi print 'P 48/48 V 16 K 144 PH 176 T 186  msdu-desc: 2500  sw-crypt: 0 ct-sta: 0'
[   37.984486] ath10k_ahb a800000.wifi: wmi print 'free: 53252 iram: 13432 sram: 35752'
[   38.307142] ath10k_ahb a800000.wifi: rts threshold -1
[   38.309496] ath10k_ahb a800000.wifi: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4
[   38.327118] br-lan: port 3(wlan1) entered blocking state
[   38.327185] br-lan: port 3(wlan1) entered disabled state
[   38.332030] device wlan1 entered promiscuous mode
[   38.983703] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[   38.984004] br-lan: port 3(wlan1) entered blocking state
[   38.989153] br-lan: port 3(wlan1) entered forwarding state

What warries me are these lines:
[    2.145184] 12 fixed-partitions partitions found on MTD device spi0.1
[    2.153053] OF: Bad cell count for /soc/spi@78b5000/spi-nand@1/partitions
[    2.159436] OF: Bad cell count for /soc/spi@78b5000/spi-nand@1/partitions
[    2.166624] OF: Bad cell count for /soc/spi@78b5000/spi-nand@1/partitions
[    2.173006] OF: Bad cell count for /soc/spi@78b5000/spi-nand@1/partitions

EDIT: With this blinking of blue status led on pcb during start there is some trick ? Since on @stich86 builds it blinks , but on official builds not....

357 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,025

Odp: ZTE MF289F - Porting OpenWRT

ipq4xxx w wersji rozwojowej przeszło na DSA. Modele które nie zostały przetestowane z DSA  zostały wyłączone i dotyczy to m.in ZTE MF289F. Ktoś musi przetestować czy DSA działa i jeżeli tak to podesłać łatkę żeby to znów zostało włączone.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

358 Odpowiedź przez frutis

  • frutis
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2009-11-10
  • Posty: 1,695

Odp: ZTE MF289F - Porting OpenWRT

Cezary napisał/a:

ipq4xxx w wersji rozwojowej przeszło na DSA. Modele które nie zostały przetestowane z DSA  zostały wyłączone i dotyczy to m.in ZTE MF289F. Ktoś musi przetestować czy DSA działa i jeżeli tak to podesłać łatkę żeby to znów zostało włączone.

Będziesz przygotowywał nowe buildy niebawem?

359 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,025

Odp: ZTE MF289F - Porting OpenWRT

To nie weszło do wersji stabilnej. Tylko w rozwojowej istnieje.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

360 Odpowiedź przez MiG25

  • MiG25
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2014-07-23
  • Posty: 3,796

Odp: ZTE MF289F - Porting OpenWRT

A MF286D jest już na DSA ?

No i na MF289F pewnie ,że mogę pzeestować , tylko potzebuje gotowy obraz smile

361 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,025

Odp: ZTE MF289F - Porting OpenWRT

W wersji rozwojowej już tak, jest na dsa.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

362 Odpowiedź przez stich86

  • Zarejestrowany: 2022-05-24
  • Posty: 392

Odp: ZTE MF289F - Porting OpenWRT

MiG25 napisał/a:

reboot for sure is not rebooting modem ( so i.e. will not bring connection after sim exchange). At the same time AT+CFUN=1,1 reboting also mf289f...

Also i'm pritty sure , that status- on pcb blue led was blinking during startup ( like on MF286D) , now blinks maybe once or two times and then it is on all the time...

here is a log from boot :

Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset),  D - Delta,  S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.1.1-00126
S - IMAGE_VARIANT_STRING=DAABANAZA
S - OEM_IMAGE_VERSION_STRING=CRM
S - Boot Config, 0x00000021
S - Reset status Config, 0x00000010
S - Core 0 Frequency, 0 MHz
B -       261 - PBL, Start
B -      1339 - bootable_media_detect_entry, Start
B -      1679 - bootable_media_detect_success, Start
B -      1693 - elf_loader_entry, Start
B -      5082 - auth_hash_seg_entry, Start
B -      7231 - auth_hash_seg_exit, Start
B -    579481 - elf_segs_hash_verify_entry, Start
B -    697499 - PBL, End
B -    697523 - SBL1, Start
B -    788386 - pm_device_init, Start
D -         7 - pm_device_init, Delta
B -    789850 - boot_flash_init, Start
D -     52866 - boot_flash_init, Delta
B -    846861 - boot_config_data_table_init, Start
D -      3840 - boot_config_data_table_init, Delta - (419 Bytes)
B -    854344 - clock_init, Start
D -      7564 - clock_init, Delta
B -    865949 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:0,Subtype:1
B -    869362 - sbl1_ddr_set_params, Start
B -    874459 - cpr_init, Start
D -         2 - cpr_init, Delta
B -    878841 - Pre_DDR_clock_init, Start
D -         4 - Pre_DDR_clock_init, Delta
D -     13174 - sbl1_ddr_set_params, Delta
B -    892154 - pm_driver_init, Start
D -         2 - pm_driver_init, Delta
B -    962427 - sbl1_wait_for_ddr_training, Start
D -        27 - sbl1_wait_for_ddr_training, Delta
B -    977830 - Image Load, Start
D -    153048 - QSEE Image Loaded, Delta - (299560 Bytes)
B -   1131306 - Image Load, Start
D -      1444 - SEC Image Loaded, Delta - (2048 Bytes)
B -   1141580 - Image Load, Start
D -    231178 - APPSBL Image Loaded, Delta - (473243 Bytes)
B -   1373155 - QSEE Execution, Start
D -        60 - QSEE Execution, Delta
B -   1379341 - SBL1, End
D -    683924 - SBL1, Delta
S - Flash Throughput, 2011 KB/s  (775270 Bytes,  385486 us)
S - DDR Frequency, 672 MHz


U-Boot 2012.07 [Chaos Calmer 15.05.1,IPQ4019.ILQ.6.1.0.r2-00006-P-1] (May 27 2021 - 04:33:40)

smem ram ptable found: ver: 1 len: 3
DRAM:  256 MiB
machid : 0x8010001
NAND:  spi_nand: spi_nand_flash_probe SF NAND ID ff:c8:d1:c8
SF: Detected GD5F1GQ4XB with page size 2 KiB, total 128 MiB
SF: Detected GD25Q16 with page size 4 KiB, total 2 MiB
ipq_spi: page_size: 0x100, sector_size: 0x1000, size: 0x200000
130 MiB
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
machid: 8010001
flash_type: 0
Uaztemain: enter into !
ZTE_InitFotaFlashPara: nand_curr_device=1
zte_getHandOffState: read data=0xff from 0x0
Press ESC to abort autoboot in 0 seconds
Creating 1 MTD partitions on "nand1":
0x000001800000-0x000003500000 : "mtd=0"
UBI: attaching mtd2 to ubi0
UBI: physical eraseblock size:   131072 bytes (128 KiB)
UBI: logical eraseblock size:    126976 bytes
UBI: smallest flash I/O unit:    2048
UBI: VID header offset:          2048 (aligned 2048)
UBI: data offset:                4096
UBI: attached mtd2 to ubi0
UBI: MTD device name:            "mtd=0"
UBI: MTD device size:            29 MiB
UBI: number of good PEBs:        232
UBI: number of bad PEBs:         0
UBI: max. allowed volumes:       128
UBI: wear-leveling threshold:    4096
UBI: number of internal volumes: 1
UBI: number of user volumes:     3
UBI: available PEBs:             18
UBI: total number of reserved PEBs: 214
UBI: number of PEBs reserved for bad PEB handling: 2
UBI: max/mean erase counter: 8/5
Read 0 bytes from volume kernel to 84000000
No size specified -> Using max size (3174400)
## Booting kernel from FIT Image at 84000000 ...
   Using 'config@ap.dk04.1-c1' configuration
   Trying 'kernel-1' kernel subimage
     Description:  ARM OpenWrt Linux-5.15.69
     Type:         Kernel Image
     Compression:  uncompressed
     Data Start:   0x840000e4
     Data Size:    3147848 Bytes = 3 MiB
     Architecture: ARM
     OS:           Linux
     Load Address: 0x80208000
     Entry Point:  0x80208000
     Hash algo:    crc32
     Hash value:   55454943
     Hash algo:    sha1
     Hash value:   1b1dd4d45b3f65a1c7c19253dfa2acbc1b991d15
   Verifying Hash Integrity ... crc32+ sha1+ OK
## Flattened Device Tree from FIT Image at 84000000
   Using 'config@ap.dk04.1-c1' configuration
   Trying 'fdt-1' FDT blob subimage
     Description:  ARM OpenWrt zte_mf289f device tree blob
     Type:         Flat Device Tree
     Compression:  uncompressed
     Data Start:   0x84300a60
     Data Size:    18771 Bytes = 18.3 KiB
     Architecture: ARM
     Hash algo:    crc32
     Hash value:   18e41883
     Hash algo:    sha1
     Hash value:   97b9d5341ff92994b8e4ec7d2f8e2fdfb5889db6
   Verifying Hash Integrity ... crc32+ sha1+ OK
   Booting using the fdt blob at 0x84300a60
   Loading Kernel Image ... OK
OK
   Loading Device Tree to 86ff8000, end 86fff952 ... OK
ipq: fdt fixup unable to find compatible node
Device nand0 not found!
invalid mtd device 'nand1'
eth0 MAC Address from ART is not valid
eth1 MAC Address from ART is not valid
Using machid 0x8010001 from environment

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 5.15.69 (builder@buildhost) (arm-openwrt-linux-muslgnueabi-gcc (OpenWrt GCC 11.3.0 r20746-a67f484e67) 11.3.0, GNU ld (GNU Binutils) 2.37) #0 SMP Sat Sep 24 21:53:53 2022
[    0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt: Machine model: ZTE MF289F
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000080000000-0x000000008fffffff]
[    0.000000]   HighMem  empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000080000000-0x0000000087dfffff]
[    0.000000]   node   0: [mem 0x0000000087e00000-0x0000000087ffffff]
[    0.000000]   node   0: [mem 0x0000000088000000-0x000000008fffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000008fffffff]
[    0.000000] percpu: Embedded 12 pages/cpu s16652 r8192 d24308 u49152
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 64960
[    0.000000] Kernel command line: ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashfs rootwait root=/dev/ubiblock0_1
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 246180K/262144K available (6763K kernel code, 610K rwdata, 1688K rodata, 1024K init, 248K bss, 15964K reserved, 0K cma-reserved, 0K highmem)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] rcu: Hierarchical RCU implementation.
[    0.000000]  Tracing variant of Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] arch_timer: cp15 timer(s) running at 48.00MHz (virt).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xb11fd3bfb, max_idle_ns: 440795203732 ns
[    0.000001] sched_clock: 56 bits at 48MHz, resolution 20ns, wraps every 4398046511096ns
[    0.000024] Switching to timer-based delay loop, resolution 20ns
[    0.000327] Calibrating delay loop (skipped), value calculated using timer frequency.. 96.00 BogoMIPS (lpj=480000)
[    0.000356] pid_max: default: 32768 minimum: 301
[    0.000615] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.000646] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.001673] CPU: Testing write buffer coherency: ok
[    0.002040] qcom_scm: convention: smc legacy
[    0.003044] Setting up static identity map for 0x80300000 - 0x8030003c
[    0.003212] rcu: Hierarchical SRCU implementation.
[    0.003468] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build
[    0.003806] smp: Bringing up secondary CPUs ...
[    0.007093] smp: Brought up 1 node, 4 CPUs
[    0.007129] SMP: Total of 4 processors activated (384.00 BogoMIPS).
[    0.007144] CPU: All CPU(s) started in SVC mode.
[    0.012655] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[    0.012816] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.012852] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[    0.013099] pinctrl core: initialized pinctrl subsystem
[    0.014770] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[    0.015160] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.016252] thermal_sys: Registered thermal governor 'step_wise'
[    0.016672] cpuidle: using governor ladder
[    0.016734] cpuidle: using governor menu
[    0.044002] cryptd: max_cpu_qlen set to 1000
[    0.048086] usbcore: registered new interface driver usbfs
[    0.048163] usbcore: registered new interface driver hub
[    0.048226] usbcore: registered new device driver usb
[    0.048276] pps_core: LinuxPPS API ver. 1 registered
[    0.048290] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.048320] PTP clock support registered
[    0.050398] clocksource: Switched to clocksource arch_sys_counter
[    0.051317] NET: Registered PF_INET protocol family
[    0.051542] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear)
[    0.052354] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[    0.052411] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.052434] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear)
[    0.052478] TCP bind hash table entries: 2048 (order: 2, 16384 bytes, linear)
[    0.052534] TCP: Hash tables configured (established 2048 bind 2048)
[    0.052651] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.052699] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.052971] NET: Registered PF_UNIX/PF_LOCAL protocol family
[    0.053029] PCI: CLS 0 bytes, default 64
[    0.055243] workingset: timestamp_bits=14 max_order=16 bucket_order=2
[    0.060198] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.060230] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.192623] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
[    0.195378] qcom-pcie 40000000.pci: host bridge /soc/pci@40000000 ranges:
[    0.195457] qcom-pcie 40000000.pci:       IO 0x0040200000..0x00402fffff -> 0x0040200000
[    0.195495] qcom-pcie 40000000.pci:      MEM 0x0040300000..0x0040ffffff -> 0x0040300000
[    0.371986] qcom-pcie 40000000.pci: iATU unroll: disabled
[    0.372020] qcom-pcie 40000000.pci: Detected iATU regions: 32 outbound, 8 inbound
[    1.372315] qcom-pcie 40000000.pci: Phy link never came up
[    1.372478] qcom-pcie 40000000.pci: PCI host bridge to bus 0000:00
[    1.372500] pci_bus 0000:00: root bus resource [bus 00-ff]
[    1.372527] pci_bus 0000:00: root bus resource [io  0x0000-0xfffff] (bus address [0x40200000-0x402fffff])
[    1.372547] pci_bus 0000:00: root bus resource [mem 0x40300000-0x40ffffff]
[    1.372603] pci 0000:00:00.0: [17cb:1001] type 01 class 0x060400
[    1.372640] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x00000fff]
[    1.372717] pci 0000:00:00.0: PME# supported from D0 D3hot
[    1.374352] PCI: bus0: Fast back to back transfers disabled
[    1.375820] PCI: bus1: Fast back to back transfers enabled
[    1.375869] pci 0000:00:00.0: BAR 0: assigned [mem 0x40300000-0x40300fff]
[    1.375899] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[    1.378778] pcieport 0000:00:00.0: AER: enabled with IRQ 103
[    1.380965] bam-dma-engine 8e04000.dma: num-channels unspecified in dt
[    1.380997] bam-dma-engine 8e04000.dma: num-ees unspecified in dt
[    1.382359] tcsr 1949000.tcsr: setting wifi_glb_cfg = 41000000
[    1.382469] tcsr 194b000.tcsr: setting usb hs phy mode select = e700e7
[    1.382564] tcsr 1953000.ess_tcsr: setting ess interface select = 0
[    1.382661] tcsr 1957000.tcsr: setting wifi_noc_memtype_m0_m2 = 2222222
[    1.382991] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    1.384772] msm_serial 78af000.serial: msm_serial: detected port #0
[    1.384825] msm_serial 78af000.serial: uartclk = 1843200
[    1.384883] 78af000.serial: ttyMSM0 at MMIO 0x78af000 (irq = 33, base_baud = 115200) is a MSM
[    1.384921] msm_serial: console setup on port #0
[    2.058978] printk: console [ttyMSM0] enabled
[    2.064136] msm_serial: driver initialized
[    2.073254] loop: module loaded
[    2.074317] spi_qup 78b5000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64
[    2.076903] spi-nor spi0.0: gd25q16 (2048 Kbytes)
[    2.082608] 8 fixed-partitions partitions found on MTD device spi0.0
[    2.087112] Creating 8 MTD partitions on "spi0.0":
[    2.093550] 0x000000000000-0x000000040000 : "0:SBL1"
[    2.098712] 0x000000040000-0x000000060000 : "0:MIBIB"
[    2.103782] 0x000000060000-0x0000000c0000 : "0:QSEE"
[    2.108736] 0x0000000c0000-0x0000000d0000 : "0:CDT"
[    2.113765] 0x0000000d0000-0x0000000e0000 : "0:DDRPARAMS"
[    2.118301] 0x0000000e0000-0x0000000f0000 : "0:APPSBLENV"
[    2.123911] 0x0000000f0000-0x0000001b0000 : "0:APPSBL"
[    2.129243] 0x0000001b0000-0x000000200000 : "0:reserved1"
[    2.137890] spi-nand spi0.1: GigaDevice SPI NAND was found.
[    2.139277] spi-nand spi0.1: 128 MiB, block size: 128 KiB, page size: 2048, OOB size: 128
[    2.145184] 12 fixed-partitions partitions found on MTD device spi0.1
[    2.153053] OF: Bad cell count for /soc/spi@78b5000/spi-nand@1/partitions
[    2.159436] OF: Bad cell count for /soc/spi@78b5000/spi-nand@1/partitions
[    2.166624] OF: Bad cell count for /soc/spi@78b5000/spi-nand@1/partitions
[    2.173006] OF: Bad cell count for /soc/spi@78b5000/spi-nand@1/partitions
[    2.180137] Creating 12 MTD partitions on "spi0.1":
[    2.186524] 0x000000000000-0x0000000a0000 : "fota-flag"
[    2.193900] 0x0000000a0000-0x000000120000 : "ART"
[    2.198635] 0x000000120000-0x0000001a0000 : "mac"
[    2.203623] 0x0000001a0000-0x000000260000 : "reserved2"
[    2.208976] 0x000000260000-0x000000660000 : "cfg-param"
[    2.224785] 0x000000660000-0x000000a60000 : "log"
[    2.238557] 0x000000a60000-0x000000b00000 : "oops"
[    2.241221] 0x000000b00000-0x000001000000 : "reserved3"
[    2.259244] 0x000001000000-0x000001800000 : "web"
[    2.286138] 0x000001800000-0x000003500000 : "rootfs"
[    2.381742] mtd: device 17 (rootfs) set to be root filesystem
[    2.383157] mtdsplit: no squashfs found in "rootfs"
[    2.386499] 0x000003500000-0x000004e00000 : "data"
[    2.473800] 0x000004e00000-0x000008000000 : "fota"
[    2.688219] ESS reset ok!
[    2.762510] ESS reset ok!
[    3.084029] PHY 0 single test PSGMII issue happen!
[    3.149664] PHY 1 single test PSGMII issue happen!
[    3.215317] PHY 2 single test PSGMII issue happen!
[    3.280992] PHY 3 single test PSGMII issue happen!
[    3.346647] PHY 4 single test PSGMII issue happen!
[    3.413052] PHY0 test see issue!
[    3.417544] PHY1 test see issue!
[    3.422020] PHY2 test see issue!
[    3.426504] PHY3 test see issue!
[    3.430991] PHY4 test see issue!
[    3.505263] ESS reset ok!
[    4.265475] i2c_dev: i2c /dev entries driver
[    4.267324] sdhci: Secure Digital Host Controller Interface driver
[    4.268826] sdhci: Copyright(c) Pierre Ossman
[    4.274886] sdhci-pltfm: SDHCI platform and OF driver helper
[    4.283090] NET: Registered PF_INET6 protocol family
[    4.286589] Segment Routing with IPv6
[    4.289950] In-situ OAM (IOAM) with IPv6
[    4.293623] NET: Registered PF_PACKET protocol family
[    4.297543] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    4.302466] 8021q: 802.1Q VLAN Support v1.8
[    4.315582] Registering SWP/SWPB emulation handler
[    4.329408] ubi0: attaching mtd17
[    5.018649] ubi0: scanning is finished
[    5.055445] ubi0: attached mtd17 (name "rootfs", size 29 MiB)
[    5.055562] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    5.060257] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    5.067126] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[    5.073978] ubi0: good PEBs: 232, bad PEBs: 0, corrupted PEBs: 0
[    5.080713] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
[    5.086907] ubi0: max/mean erase counter: 8/5, WL threshold: 4096, image sequence number: 3329320032
[    5.093997] ubi0: available PEBs: 0, total reserved PEBs: 232, PEBs reserved for bad PEB handling: 20
[    5.103342] ubi0: background thread "ubi_bgt0d" started, PID 125
[ ▒[    5.138476] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[    5.141327] Freeing unused kernel image (initmem) memory: 1024K
[    5.184171] Run /sbin/init as init process
[    6.388022] init: Console is alive
[    6.388339] init: - watchdog -
[    6.423430] random: crng init done
[    8.220563] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    8.635756] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[    8.635935] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[    8.640519] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f665 hci version 0x100 quirks 0x0000002002010010
[    8.647830] xhci-hcd xhci-hcd.0.auto: irq 106, io mem 0x08a00000
[    8.657359] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[    8.663420] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[    8.668685] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
[    8.676934] hub 1-0:1.0: USB hub found
[    8.685456] hub 1-0:1.0: 1 port detected
[    8.687019] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[    8.691225] hub 2-0:1.0: USB hub found
[    8.698747] hub 2-0:1.0: 1 port detected
[    8.702762] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[    8.706368] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
[    8.711913] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f665 hci version 0x100 quirks 0x0000002002010010
[    8.719261] xhci-hcd xhci-hcd.1.auto: irq 107, io mem 0x06000000
[    8.728799] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[    8.734871] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
[    8.740125] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed
[    8.749575] hub 3-0:1.0: USB hub found
[    8.754362] hub 3-0:1.0: 1 port detected
[    8.758439] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[    8.762648] hub 4-0:1.0: USB hub found
[    8.770187] hub 4-0:1.0: config failed, hub doesn't have any ports! (err -19)
[    8.776058] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    8.781982] init: - preinit -
[    9.821411] usb 2-1: new SuperSpeed USB device number 2 using xhci-hcd
[   11.001832] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[   13.446451] UBIFS (ubi0:2): Mounting in unauthenticated mode
[   13.446709] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" started, PID 232
[   13.623025] UBIFS (ubi0:2): recovery needed
[   13.999904] UBIFS (ubi0:2): recovery completed
[   14.000491] UBIFS (ubi0:2): UBIFS: mounted UBI device 0, volume 2, name "rootfs_data"
[   14.003360] UBIFS (ubi0:2): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[   14.011358] UBIFS (ubi0:2): FS size: 17776640 bytes (16 MiB, 140 LEBs), max 150 LEBs, journal size 1015809 bytes (0 MiB, 7 LEBs)
[   14.021218] UBIFS (ubi0:2): reserved for root: 839634 bytes (819 KiB)
[   14.032831] UBIFS (ubi0:2): media format: w5/r0 (latest is w5/r0), UUID D56679E6-0054-41CD-9A20-A2BDAEF4DE9F, small LPT model
[   14.078167] mount_root: switching to ubifs overlay
[   14.128827] urandom-seed: Seeding with /etc/urandom.seed
[   14.515642] procd: - early -
[   14.516212] procd: - watchdog -
[   15.189830] procd: - watchdog -
[   15.380533] procd: - ubus -
[   15.808062] procd: - init -
Please press Enter to activate this console.
[   17.089063] kmodloader: loading kernel modules from /etc/modules.d/*
[   17.164683] urngd: v1.0.2 started.
[   17.235389] usbcore: registered new interface driver cdc_wdm
[   17.236159] Loading modules backported from Linux version v5.15.58-0-g7d8048d4e064
[   17.240136] Backport generated by backports.git v5.15.58-1-0-g42a95ce7
[   17.259920] usbcore: registered new interface driver usbserial_generic
[   17.260025] usbserial: USB Serial support registered for generic
[   17.335610] PPP generic driver version 2.4.2
[   17.360504] NET: Registered PF_PPPOX protocol family
[   17.381823] qmi_wwan 2-1:1.3: cdc-wdm0: USB WDM device
[   17.383821] qmi_wwan 2-1:1.3 wwan0: register 'qmi_wwan' at usb-xhci-hcd.0.auto-1, WWAN/QMI device, 96:32:b1:3f:f2:7d
[   17.386189] usbcore: registered new interface driver qmi_wwan
[   19.004731] ath10k_ahb a000000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003b00ff sub 0000:0000
[   19.004802] ath10k_ahb a000000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[   19.016625] ath10k_ahb a000000.wifi: firmware ver 10.4b-ct-4019-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 6b2b5c5b
[   19.076691] ath10k_ahb a000000.wifi: Loading BDF type 0
[   19.077332] ath10k_ahb a000000.wifi: board_file api 2 bmi_id 0:20 crc32 1323eb04
[   20.376298] ath10k_ahb a000000.wifi: 10.4 wmi init: vdevs: 16  peers: 48  tid: 96
[   20.376371] ath10k_ahb a000000.wifi: msdu-desc: 2500  skid: 32
[   20.425914] ath10k_ahb a000000.wifi: wmi print 'P 48/48 V 16 K 144 PH 176 T 186  msdu-desc: 2500  sw-crypt: 0 ct-sta: 0'
[   20.427615] ath10k_ahb a000000.wifi: wmi print 'free: 53252 iram: 13432 sram: 35752'
[   20.570999] ath10k_ahb a000000.wifi: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-nvmem max-sta 32 raw 0 hwcrypto 1
[   22.016137] ath10k_ahb a800000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003b00ff sub 0000:0000
[   22.016207] ath10k_ahb a800000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[   22.037649] ath10k_ahb a800000.wifi: firmware ver 10.4b-ct-4019-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 6b2b5c5b
[   22.091585] ath10k_ahb a800000.wifi: Loading BDF type 0
[   22.091846] ath10k_ahb a800000.wifi: board_file api 2 bmi_id 0:21 crc32 1323eb04
[   23.391867] ath10k_ahb a800000.wifi: 10.4 wmi init: vdevs: 16  peers: 48  tid: 96
[   23.391939] ath10k_ahb a800000.wifi: msdu-desc: 2500  skid: 32
[   23.439102] ath10k_ahb a800000.wifi: wmi print 'P 48/48 V 16 K 144 PH 176 T 186  msdu-desc: 2500  sw-crypt: 0 ct-sta: 0'
[   23.440837] ath10k_ahb a800000.wifi: wmi print 'free: 53252 iram: 13432 sram: 35752'
[   23.578872] ath10k_ahb a800000.wifi: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-nvmem max-sta 32 raw 0 hwcrypto 1
[   23.751018] usbcore: registered new interface driver option
[   23.751136] usbserial: USB Serial support registered for GSM modem (1-port)
[   23.755898] option 2-1:1.0: GSM modem (1-port) converter detected
[   23.762778] usb 2-1: GSM modem (1-port) converter now attached to ttyUSB0
[   23.769052] option 2-1:1.1: GSM modem (1-port) converter detected
[   23.775773] usb 2-1: GSM modem (1-port) converter now attached to ttyUSB1
[   23.781994] option 2-1:1.2: GSM modem (1-port) converter detected
[   23.788594] usb 2-1: GSM modem (1-port) converter now attached to ttyUSB2
[   23.797692] kmodloader: done loading kernel modules from /etc/modules.d/*
[   32.846583] br-lan: port 1(eth0) entered blocking state
[   32.846645] br-lan: port 1(eth0) entered disabled state
[   32.851146] device eth0 entered promiscuous mode
[   33.910502] br-lan: port 1(eth0) entered blocking state
[   33.910593] br-lan: port 1(eth0) entered forwarding state
[   33.915099] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   35.531478] ath10k_ahb a000000.wifi: 10.4 wmi init: vdevs: 16  peers: 48  tid: 96
[   35.531548] ath10k_ahb a000000.wifi: msdu-desc: 2500  skid: 32
[   35.580454] ath10k_ahb a000000.wifi: wmi print 'P 48/48 V 16 K 144 PH 176 T 186  msdu-desc: 2500  sw-crypt: 0 ct-sta: 0'
[   35.581407] ath10k_ahb a000000.wifi: wmi print 'free: 53252 iram: 13432 sram: 35752'
[   35.912235] ath10k_ahb a000000.wifi: rts threshold -1
[   35.912689] ath10k_ahb a000000.wifi: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4
[   35.921726] br-lan: port 2(wlan0) entered blocking state
[   35.927238] br-lan: port 2(wlan0) entered disabled state
[   35.933179] device wlan0 entered promiscuous mode
[   36.034357] ath10k_ahb a000000.wifi: NOTE:  Firmware DBGLOG output disabled in debug_mask: 0x10000000
[   36.262904] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   36.265216] br-lan: port 2(wlan0) entered blocking state
[   36.268766] br-lan: port 2(wlan0) entered forwarding state
[   37.935367] ath10k_ahb a800000.wifi: 10.4 wmi init: vdevs: 16  peers: 48  tid: 96
[   37.935454] ath10k_ahb a800000.wifi: msdu-desc: 2500  skid: 32
[   37.982674] ath10k_ahb a800000.wifi: wmi print 'P 48/48 V 16 K 144 PH 176 T 186  msdu-desc: 2500  sw-crypt: 0 ct-sta: 0'
[   37.984486] ath10k_ahb a800000.wifi: wmi print 'free: 53252 iram: 13432 sram: 35752'
[   38.307142] ath10k_ahb a800000.wifi: rts threshold -1
[   38.309496] ath10k_ahb a800000.wifi: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4
[   38.327118] br-lan: port 3(wlan1) entered blocking state
[   38.327185] br-lan: port 3(wlan1) entered disabled state
[   38.332030] device wlan1 entered promiscuous mode
[   38.983703] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[   38.984004] br-lan: port 3(wlan1) entered blocking state
[   38.989153] br-lan: port 3(wlan1) entered forwarding state

What warries me are these lines:
[    2.145184] 12 fixed-partitions partitions found on MTD device spi0.1
[    2.153053] OF: Bad cell count for /soc/spi@78b5000/spi-nand@1/partitions
[    2.159436] OF: Bad cell count for /soc/spi@78b5000/spi-nand@1/partitions
[    2.166624] OF: Bad cell count for /soc/spi@78b5000/spi-nand@1/partitions
[    2.173006] OF: Bad cell count for /soc/spi@78b5000/spi-nand@1/partitions

EDIT: With this blinking of blue status led on pcb during start there is some trick ? Since on @stich86 builds it blinks , but on official builds not....

There is an error on DTS, I’ll submit new PR to patch it. The GPIO of internal LED is wrong

363 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,025

Odp: ZTE MF289F - Porting OpenWRT

Został zgłoszony PR do DSA. Sprawdźcie czy to działa, bo mam wrażenie że jedna wersja jest dobrze a druga ma odwrócowe lan z wanem. Obym się mylił.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

364 Odpowiedź przez MiG25

  • MiG25
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2014-07-23
  • Posty: 3,796

Odp: ZTE MF289F - Porting OpenWRT

Jak mi to ktoś skompiluje ,to jestem gotów. Ja tego nie umiem i nigdy nie robiłem...

365 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,025

Odp: ZTE MF289F - Porting OpenWRT

Tu jest: https://dl.eko.one.pl/test/openwrt-ipq4 … pgrade.bin

Wgrywać bez zachowania konfiguracji i nie odtwarzać backupu ze starej wersji. Wersja do testów, nie używać tego na stałe. Nie ma luci, wszystko do sprawdzenia z konsoli. Podstawowy obraz jaki openwrt daje, bez żadnych dodatkowych ustawień czy moich skryptów.

Jest to commit c3b9f00aaae37db603f6107d93245e0d8aa8a2d0 z nałożonym patchem https://github.com/openwrt/openwrt/pull/10908

Do sprawdzenia
- czy działają porty ethernet
- czy ich przypisanie jest właściwe (lan/wan)
- czy działają led
- czy działa wifi
- czy działa modem

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

366 Odpowiedź przez MiG25

  • MiG25
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2014-07-23
  • Posty: 3,796

Odp: ZTE MF289F - Porting OpenWRT

ok , dzięki.
Porty ethernet działają , dolny przydziela adres dhcp ( działa jako lan) , górny działa jako wan  ( więc nie pomylone) , po podłączeniu zgodnie z przeznaczeniem działa jako router.
Po włączeniu wifi ( sieć otwarta ) przydziela tez adres , jest internet z wanu.
po usunięciu wanu i ustawieniu modemu jako wan , przez wifi internet jest  , i przez dolne lan też.

Ledy działają jak działały ,ta niebieska wewnętrzna na pcb dalej praktycznie swieci się cały czas ,nawet podczas bootowania , za to zauważyłem ,że podczas wgrywania softu(flashowania) mruga...

Dalej reboot nie resetuje modemu tylko sam router , za to AT+CFUN=1,1 resetuje modem razem z routerem....

367 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,025

Odp: ZTE MF289F - Porting OpenWRT

@smereka sprawdził byś na swoim czy wszystko jest ok. Jak tak to ja usuwam swoje testy i czekamy na włączenie tego do źródeł.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

368 Odpowiedź przez smereka

  • Zarejestrowany: 2014-07-09
  • Posty: 2,443

Odp: ZTE MF289F - Porting OpenWRT

Sprawdze. A mozna ten soft ozenic z lucyna?

369 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,025

Odp: ZTE MF289F - Porting OpenWRT

smereka napisał/a:

Sprawdze. A mozna ten soft ozenic z lucyna?

Jak sobie doinstalujesz to tak, tylko tego nie rób - na razie sprawdź czy wszystko działa, a docelowo poczekaj aż zbuduje się w openwrt.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

370 Odpowiedź przez smereka

  • Zarejestrowany: 2014-07-09
  • Posty: 2,443

Odp: ZTE MF289F - Porting OpenWRT

Ok. Napisz proszę jakie polecenia sprawdza w który port jestem wpięty. W lucynie to było proste a tutaj co mam porównać wzrokowo z fizycznym portem?

371 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,025

Odp: ZTE MF289F - Porting OpenWRT

Wolisz luci to doinstaluj luci.

Z konsoli np.

cat /sys/class/net/lan/speed

Jak się podłączysz pod port lan, powinno zwrócić szybkość portu. Tak samo

cat /sys/class/net/wan/speed

Jak się podłączysz pod port wan oznaczony wan

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

372 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,025

Odp: ZTE MF289F - Porting OpenWRT

Łatka została dodana, za kilka godzin powinny być już dostępne obrazy od openwrt.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

373 Odpowiedź przez tango38317

  • Zarejestrowany: 2022-10-10
  • Posty: 27

Odp: ZTE MF289F - Porting OpenWRT

Hello,
i´m also owner of an ZTE MF289F and try to migrate to OPENWRT build.
im able to connect to console, but if i try to copy the itb file to the router i receive following error:

tftp openwrt-ipq40xx-generic-zte_mf289f-initramfs-fit-zImage.itb bootm $loadaddr
...
...
...
Using eth0 device
TFTP from Server 192.168.0.2; our IP address is 192.168.0.1
Filename 'bootm'.
Load address: 0x0

Error specified load address not allowed.


maybe somene can help me or give me a hint to flash openwrt.

sorry, i´m from Austria, not a polish guy :-), tried to read with google translate, but did not find any other user with this issue.

many thanks
Chris.

374 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,025

Odp: ZTE MF289F - Porting OpenWRT

These are two lines, not one.

tftp openwrt-ipq40xx-generic-zte_mf289f-initramfs-fit-zImage.itb<enter>
bootm $loadaddr<enter>

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

375 Odpowiedź przez smereka

  • Zarejestrowany: 2014-07-09
  • Posty: 2,443

Odp: ZTE MF289F - Porting OpenWRT

Wszystko co napisał Mig25 to u mnie się pojawiło ząb w ząb no i Twoje komendy:

root@OpenWrt:~# cat /sys/class/net/lan/speed
1000
root@OpenWrt:~# cat /sys/class/net/wan/speed
1000
root@OpenWrt:~#

niestety Lucyna marudzi:

root@OpenWrt:~# opkg update
Downloading https://downloads.openwrt.org/snapshots … ackages.gz
Updated list of available packages in /var/opkg-lists/openwrt_core
Downloading https://downloads.openwrt.org/snapshots … ckages.sig
Signature check passed.
Downloading https://downloads.openwrt.org/snapshots … ackages.gz
Updated list of available packages in /var/opkg-lists/openwrt_base
Downloading https://downloads.openwrt.org/snapshots … ckages.sig
Signature check passed.
root@OpenWrt:~# opkg install luci
Unknown package 'luci'.
Collected errors:
* opkg_install_cmd: Cannot install package luci.
root@OpenWrt:~#