Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.3.1-00147
S - IMAGE_VARIANT_STRING=HAACANAAA
S - OEM_IMAGE_VERSION_STRING=xiaoyang-gv
S - Boot Config, 0x000002e5
B - 203 - PBL, Start
B - 2739 - bootable_media_detect_entry, Start
B - 3447 - bootable_media_detect_success, Start
B - 3451 - elf_loader_entry, Start
B - 6121 - auth_hash_seg_entry, Start
B - 6368 - auth_hash_seg_exit, Start
B - 68630 - elf_segs_hash_verify_entry, Start
B - 131331 - PBL, End
B - 139202 - SBL1, Start
B - 190381 - GCC [RstStat:0x10, RstDbg:0x600000] WDog Stat : 0x4
B - 196664 - pm_device_init, Start
B - 315156 - PM_SET_VAL:Skip
D - 117974 - pm_device_init, Delta
B - 317474 - pm_driver_init, Start
D - 5368 - pm_driver_init, Delta
B - 323940 - clock_init, Start
D - 2135 - clock_init, Delta
B - 327905 - boot_flash_init, Start
D - 11864 - boot_flash_init, Delta
B - 343552 - boot_config_data_table_init, Start
D - 3202 - boot_config_data_table_init, Delta - (575 Bytes)
B - 351085 - Boot Setting : 0x00000600
B - 355020 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:0,Subtype:16
B - 361943 - sbl1_ddr_set_params, Start
B - 365756 - CPR configuration: 0x300
B - 369141 - cpr_init, Start
B - 372039 - Rail:0 Mode: 5 Voltage: 824000
B - 377163 - CL CPR settled at 776000mV
B - 379999 - Rail:1 Mode: 5 Voltage: 880000
B - 384178 - Rail:1 Mode: 7 Voltage: 928000
D - 16470 - cpr_init, Delta
B - 391071 - Pre_DDR_clock_init, Start
B - 395097 - Pre_DDR_clock_init, End
B - 398482 - DDR Type : PCDDR3
B - 404186 - do ddr sanity test, Start
D - 1067 - do ddr sanity test, Delta
B - 408944 - DDR: Start of HAL DDR Boot Training
B - 413671 - DDR: End of HAL DDR Boot Training
B - 419344 - DDR: Checksum to be stored on flash is -31203832
B - 429653 - Image Load, Start
D - 224084 - QSEE Image Loaded, Delta - (1373936 Bytes)
B - 653828 - Image Load, Start
D - 30 - SEC Image Loaded, Delta - (0 Bytes)
B - 661514 - Image Load, Start
D - 10736 - DEVCFG Image Loaded, Delta - (26004 Bytes)
B - 672342 - Image Load, Start
D - 25254 - RPM Image Loaded, Delta - (105964 Bytes)
B - 697657 - Image Load, Start
D - 96563 - APPSBL Image Loaded, Delta - (589900 Bytes)
B - 794311 - QSEE Execution, Start
D - 61 - QSEE Execution, Delta
B - 800106 - USB D+ check, Start
D - 0 - USB D+ check, Delta
B - 806511 - SBL1, End
D - 669627 - SBL1, Delta
S - Flash Throughput, 6752 KB/s (2096379 Bytes, 310451 us)
S - DDR Frequency, 466 MHz
S - Core 0 Frequency, 800 MHz
U-Boot 2016.01 (Sep 28 2020 - 09:05:55 +0000), Build: jenkins-common_router_openwrt_ota_publish-383
DRAM: smem ram ptable found: ver: 1 len: 4
512 MiB
NAND: ONFI device found
ID = 1590aac8
Vendor = c8
Device = aa
qpic_nand: changing oobsize to 64 from 128 bytes
SF: Unsupported flash IDs: manuf ff, jedec ffff, ext_jedec ffff
ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0)
256 MiB
MMC: sdhci: Node Not found, skipping initialization
PCI Link Intialized
PCI1 is not defined in the device tree
In: serial@78B3000
Out: serial@78B3000
Err: serial@78B3000
machid: 8010010
MMC Device 0 not found
eth5 MAC Address from ART is not valid
write phy_id=1, reg(0x8074):0x0670
write phy_id=2, reg(0x8074):0x0670
write phy_id=3, reg(0x8074):0x0670
write phy_id=4, reg(0x8074):0x0670
bootwait is on, bootdelay=5
Hit any key to stop autoboot: 0
detect button press, continue check 5 secs
detect button pressed 5 secs !
confirm to launch xq_upgrade !
cmd=dhcp
Net: MAC0 addr:9c:9d:7e:75:35:b6
PHY ID1: 0x4d
PHY ID2: 0xd0b1
EDMA ver 1 hw init
Num rings - TxDesc:1 (0-0) TxCmpl:1 (7-7)
RxDesc:1 (15-15) RxFill:1 (7-7)
ipq807x_edma_alloc_rings: successfull
ipq807x_edma_setup_ring_resources: successfull
ipq807x_edma_configure_rings: successfull
ipq807x_edma_hw_init: successfull
board_eth_init: ipq807x_edma_init successed
eth0
ipq807x_eth_halt: done
eth0 PHY0 Down Speed :10 Half duplex
eth0 PHY1 up Speed :10 Full duplex
eth0 PHY2 Down Speed :10 Half duplex
eth0 PHY3 up Speed :1000 Full duplex
eth0 PHY4 Down Speed :10 Half duplex
eth0 PHY5 Down Speed :10 Half duplex
ipq807x_eth_init: done
BOOTP broadcast 1
BOOTP broadcast 2
