U-Boot 1.1.4 (Jun  2 2017 - 03:03:35)

ap152 - Dragonfly 1.0DRAM:
sri
ath_ddr_initial_config(278): (ddr2 init)
ath_sys_frequency: cpu 775 ddr 650 ahb 258
Tap values = (0x12, 0x12, 0x12, 0x12)
128 MB
Top of RAM usable for U-Boot at: 88000000
Reserving 420k for U-Boot at: 87f94000
Reserving 192k for malloc() at: 87f64000
Reserving 44 Bytes for Board Info at: 87f63fd4
Reserving 36 Bytes for Global Data at: 87f63fb0
Reserving 128k for boot params() at: 87f43fb0
Stack Pointer at: 87f43f98
Now running in RAM - U-Boot at: 87f94000
Flash Manuf Id 0xc2, DeviceId0 0x20, DeviceId1 0x15
flash size 2MB, sector count = 32
Flash:  2 MB
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   ath_gmac_enet_initialize...
No valid address in Flash. Using fixed address
ath_gmac_enet_initialize: reset mask:c02200
athr_mgmt_init (MDC/MDIO config)::done
Dragonfly  ----> S17 PHY *
athrs17_reg_init: complete
SGMII in forced mode
athr_gmac_sgmii_setup SGMII done
: cfg1 0x80000000 cfg2 0x7114
eth0: 00:03:7f:ff:ff:ff
ath_gmac_phy_setup
eth0 up
eth0
Qualcomm Atheros SPI NAND Driver, Version 0.1 (c) 2014  Qualcomm Atheros Inc.
ath_spi_nand_ecc: furture feat = 0x18
ath_spi_nand_ecc: middle feat = 0x18
ath_parse_read_id: SPI NAND M.Id: 0xef D.Id1: 0xaa D.Id2: 0x21
====== NAND Parameters ======
sc addr = 0x87ff5d40 page(write size) = 0x800 (erase size) block = 0x20000
Setting 0x181162c0 to 0x4b962100
Uaztemain: enter into !
zte_getHandOffState: read data=0x20 from 0x0
Uaztemain: no need to update '▒▒▒▒ (%'
Hit any key to stop autoboot:  0

Loading from device 0: ath-spi-nand (offset 0x1300000)
   Image Name:   MIPS OpenWrt Linux-5.10.138
   Created:      2022-09-03  18:56:06 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    2435438 Bytes =  2.3 MB
   Load Address: 80060000
   Entry Point:  80060000
## Booting image at 81000000 ...
   Image Name:   MIPS OpenWrt Linux-5.10.138
   Created:      2022-09-03  18:56:06 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    2435438 Bytes =  2.3 MB
   Load Address: 80060000
   Entry Point:  80060000
   Verifying Checksum at 0x81000040 ...OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80060000) ...
## Giving linux memsize in bytes, 134217728

Starting kernel ...

[    0.000000] Linux version 5.10.138 (cezary@eko.one.pl) (mips-openwrt-linux-musl-gcc (OpenWrt GCC 11.2.0 r19162-a036c1d43b) 11.2.0, GNU ld (GNU Binutils) 2.37) #0 Sat Sep 3 18:56:06 2022
[    0.000000] printk: bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019750 (MIPS 74Kc)
[    0.000000] MIPS: machine is ZTE MF286
[    0.000000] SoC: Qualcomm Atheros QCA956X ver 1 rev 0
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 32480
[    0.000000] Kernel command line: console=ttyS0,115200n8 rootfstype=squashfs,jffs2
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 120572K/131072K available (6347K kernel code, 599K rwdata, 784K rodata, 1220K init, 214K bss, 10500K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS: 51
[    0.000000] CPU clock: 775.000 MHz
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4932285024 ns
[    0.000007] sched_clock: 32 bits at 387MHz, resolution 2ns, wraps every 5541893118ns
[    0.008282] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[    0.074811] pid_max: default: 32768 minimum: 301
[    0.079806] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.087519] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.097691] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build
[    0.108403] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.118806] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[    0.126067] pinctrl core: initialized pinctrl subsystem
[    0.135590] NET: Registered protocol family 16
[    0.140917] thermal_sys: Registered thermal governor 'step_wise'
[    0.191988] clocksource: Switched to clocksource MIPS
[    0.204817] NET: Registered protocol family 2
[    0.209619] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
[    0.217999] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[    0.226917] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.235016] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.242464] TCP: Hash tables configured (established 1024 bind 1024)
[    0.249290] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[    0.256231] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[    0.263884] NET: Registered protocol family 1
[    0.268499] PCI: CLS 0 bytes, default 32
[    0.278484] workingset: timestamp_bits=14 max_order=15 bucket_order=1
[    0.288859] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.295059] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.307062] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[    0.317372] pinctrl-single 1804002c.pinmux: 544 pins, size 68
[    0.324505] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.333341] printk: console [ttyS0] disabled
[    0.337909] 18020000.uart: ttyS0 at MMIO 0x18020000 (irq = 9, base_baud = 1562500) is a 16550A
[    0.347053] printk: console [ttyS0] enabled
[    0.347053] printk: console [ttyS0] enabled
[    0.356119] printk: bootconsole [early0] disabled
[    0.356119] printk: bootconsole [early0] disabled
[    0.382593] spi-nand spi0.1: Winbond SPI NAND was found.
[    0.388101] spi-nand spi0.1: 128 MiB, block size: 128 KiB, page size: 2048, OOB size: 64
[    0.398848] 6 fixed-partitions partitions found on MTD device (null)
[    0.405505] OF: Bad cell count for /ahb/spi@1f000000/flash@1/partitions
[    0.412381] OF: Bad cell count for /ahb/spi@1f000000/flash@1/partitions
[    0.419922] OF: Bad cell count for /ahb/spi@1f000000/flash@1/partitions
[    0.426817] OF: Bad cell count for /ahb/spi@1f000000/flash@1/partitions
[    0.434424] Creating 6 MTD partitions on "(null)":
[    0.439389] 0x000000000000-0x000000140000 : "fota-flag"
[    0.449334] 0x000000140000-0x000000280000 : "caldata"
[    0.457540] 0x000000280000-0x0000003c0000 : "mac"
[    0.465461] 0x0000003c0000-0x000001300000 : "ubiconcat0"
[    0.486899] 0x000001300000-0x000001700000 : "kernel"
[    0.497544] 0x000001700000-0x000008000000 : "ubiconcat1"
[    0.608796] spi-nor spi0.0: mx25l1606e (2048 Kbytes)
[    0.614011] 2 fixed-partitions partitions found on MTD device spi0.0
[    0.620571] Creating 2 MTD partitions on "spi0.0":
[    0.625548] 0x000000000000-0x000000080000 : "u-boot"
[    0.632499] 0x000000080000-0x0000000a0000 : "u-boot-env"
[    0.639858] Concatenating MTD devices:
[    0.643804] (0): "ubiconcat0"
[    0.646865] (1): "ubiconcat1"
[    0.649928] into device "ubi-concat"
[    0.653669] 1 fixed-partitions partitions found on MTD device ubi-concat
[    0.660586] Creating 1 MTD partitions on "ubi-concat":
[    0.665911] 0x000000000000-0x000007840000 : "ubi"
[    1.366019] switch0: Atheros AR8337 rev. 2 switch registered on mdio.0
[    2.023513] ag71xx 19000000.eth: connected to PHY at mdio.0:00 [uid=004dd036, driver=Atheros AR8216/AR8236/AR8316]
[    2.034785] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode: sgmii
[    2.043467] NET: Registered protocol family 10
[    2.055569] Segment Routing with IPv6
[    2.059463] NET: Registered protocol family 17
[    2.064198] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    2.077595] 8021q: 802.1Q VLAN Support v1.8
[    2.085834] PCI host bridge /ahb/pcie-controller@18250000 ranges:
[    2.092207]  MEM 0x0000000012000000..0x0000000013ffffff
[    2.097603]   IO 0x0000000000000000..0x0000000000000000
[    2.103191] PCI host bridge to bus 0000:00
[    2.107437] pci_bus 0000:00: root bus resource [mem 0x12000000-0x13ffffff]
[    2.114566] pci_bus 0000:00: root bus resource [io  0x0000]
[    2.120323] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    2.127341] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    2.135573] pci 0000:00:00.0: [168c:0056] type 00 class 0x028000
[    2.141807] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[    2.148953] pci 0000:00:00.0: PME# supported from D0 D3hot
[    2.155892] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[    2.162795] pci 0000:00:00.0: BAR 0: assigned [mem 0x12000000-0x121fffff 64bit]
[    2.175334] UBI: auto-attach mtd8
[    2.178787] ubi0: attaching mtd8
[    4.895562] ubi0: scanning is finished
[    4.934233] ubi0: attached mtd8 (name "ubi", size 120 MiB)
[    4.939911] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    4.947056] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    4.954084] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[    4.961268] ubi0: good PEBs: 962, bad PEBs: 0, corrupted PEBs: 0
[    4.967479] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[    4.974942] ubi0: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 2137766154
[    4.984377] ubi0: available PEBs: 0, total reserved PEBs: 962, PEBs reserved for bad PEB handling: 19
[    4.994013] ubi0: background thread "ubi_bgt0d" started, PID 342
[    5.003162] block ubiblock0_0: created from ubi0:0(rootfs)
[    5.008840] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
[    5.040366] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[    5.054456] Freeing unused kernel memory: 1220K
[    5.059138] This architecture does not have kernel memory protection.
[    5.065823] Run /sbin/init as init process
[    5.921609] init: Console is alive
[    5.925649] init: - watchdog -
[    8.626280] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    8.713348] usbcore: registered new interface driver usbfs
[    8.719076] usbcore: registered new interface driver hub
[    8.724694] usbcore: registered new device driver usb
[    8.784048] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    8.799457] SCSI subsystem initialized
[    8.809176] ehci-fsl: Freescale EHCI Host controller driver
[    8.817746] ehci-platform: EHCI generic platform driver
[    8.823528] ehci-platform 1b000000.usb: EHCI Host Controller
[    8.829421] ehci-platform 1b000000.usb: new USB bus registered, assigned bus number 1
[    8.837666] ehci-platform 1b000000.usb: irq 13, io mem 0x1b000000
[    8.872013] ehci-platform 1b000000.usb: USB 2.0 started, EHCI 1.00
[    8.879221] hub 1-0:1.0: USB hub found
[    8.883876] hub 1-0:1.0: 1 port detected
[    8.888760] ehci-platform 1b400000.usb: EHCI Host Controller
[    8.894675] ehci-platform 1b400000.usb: new USB bus registered, assigned bus number 2
[    8.902912] ehci-platform 1b400000.usb: irq 14, io mem 0x1b400000
[    8.932011] ehci-platform 1b400000.usb: USB 2.0 started, EHCI 1.00
[    8.939192] hub 2-0:1.0: USB hub found
[    8.943877] hub 2-0:1.0: 1 port detected
[    8.956764] usbcore: registered new interface driver usb-storage
[    8.965668] usbcore: registered new interface driver uas
[    8.972529] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    8.990448] init: - preinit -
[   10.868909] random: jshn: uninitialized urandom read (4 bytes read)
[   11.067390] random: jshn: uninitialized urandom read (4 bytes read)
[   11.173029] random: jshn: uninitialized urandom read (4 bytes read)
[   12.594842] Atheros AR8216/AR8236/AR8316 mdio.0:00: Port 1 is up
[   12.603275] eth0: link up (1000Mbps/Full duplex)
[   12.609602] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   12.627199] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3[   12.658869] random: procd: uninitialized urandom read (4 bytes read)
] or [4] key and hit [enter] to select the debug level
[   16.964775] mount_root: loading kmods from internal overlay
[   17.025412] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[   17.046825] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[   17.575252] UBIFS (ubi0:1): Mounting in unauthenticated mode
[   17.592661] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 498
[   17.693203] usb 1-1: new high-speed USB device number 2 using ehci-platform
[   17.776518] UBIFS (ubi0:1): recovery needed
[   18.205313] UBIFS (ubi0:1): recovery completed
[   18.209992] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[   18.218112] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[   18.228357] UBIFS (ubi0:1): FS size: 110469120 bytes (105 MiB, 870 LEBs), journal size 5586944 bytes (5 MiB, 44 LEBs)
[   18.239329] UBIFS (ubi0:1): reserved for root: 4952683 bytes (4836 KiB)
[   18.246168] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID 1C9AE129-1E71-45F7-A7FE-EAD812F9D4BB, small LPT model
[   18.267493] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[   18.300167] block: extroot: not configured
[   18.304748] UBIFS (ubi0:1): un-mount UBI device 0
[   18.309647] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" stops
[   18.326054] UBIFS (ubi0:1): Mounting in unauthenticated mode
[   18.332473] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 508
[   18.693002] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[   18.701102] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[   18.711385] UBIFS (ubi0:1): FS size: 110469120 bytes (105 MiB, 870 LEBs), journal size 5586944 bytes (5 MiB, 44 LEBs)
[   18.722351] UBIFS (ubi0:1): reserved for root: 4952683 bytes (4836 KiB)
[   18.729182] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID 1C9AE129-1E71-45F7-A7FE-EAD812F9D4BB, small LPT model
[   19.074062] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[   19.103878] block: extroot: not configured
[   19.116382] mount_root: switching to ubifs overlay
[   19.158279] urandom-seed: Seeding with /etc/urandom.seed
[   19.322119] eth0: link down
[   19.344828] procd: - early -
[   19.348133] procd: - watchdog -
[   20.183916] procd: - watchdog -
[   20.194991] procd: - ubus -
[   20.476759] random: jshn: uninitialized urandom read (4 bytes read)
[   20.601871] random: ubusd: uninitialized urandom read (4 bytes read)
[   20.617947] random: ubusd: uninitialized urandom read (4 bytes read)
[   20.726972] procd: - init -
Please press Enter to activate this console.
[   21.868708] random: usbmode: uninitialized urandom read (4 bytes read)
[   21.890419] random: jshn: uninitialized urandom read (4 bytes read)
[   21.934452] random: ubusd: uninitialized urandom read (4 bytes read)
[   23.843831] kmodloader: loading kernel modules from /etc/modules.d/*
[   24.358768] urngd: v1.0.2 started.
[   24.605621] tun: Universal TUN/TAP device driver, 1.6
[   24.658321] fuse: init (API version 7.32)
[   24.729776] random: crng init done
[   24.733362] random: 52 urandom warning(s) missed due to ratelimiting
[   24.752824] usbcore: registered new interface driver cdc_acm
[   24.758676] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[   24.783649] usbcore: registered new interface driver cdc_wdm
[   24.804536] Loading modules backported from Linux version v5.15.58-0-g7d8048d4e064
[   24.812409] Backport generated by backports.git v5.15.58-1-0-g42a95ce7
[   24.886182] usbcore: registered new interface driver usblp
[   24.919648] usbcore: registered new interface driver usbserial_generic
[   24.926522] usbserial: USB Serial support registered for generic
[   24.948702] usbcore: registered new interface driver cdc_ether
[   24.974671] usbcore: registered new interface driver cdc_ncm
[   25.026839] usbcore: registered new interface driver huawei_cdc_ncm
[   26.000404] PPP generic driver version 2.4.2
[   26.023246] NET: Registered protocol family 24
[   26.042328] qmi_wwan 1-1:1.3: cdc-wdm0: USB WDM device
[   26.048385] qmi_wwan 1-1:1.3 wwan0: register 'qmi_wwan' at usb-1b000000.usb-1, WWAN/QMI device, 76:4f:4d:cb:85:44
[   26.059283] usbcore: registered new interface driver qmi_wwan
[   26.084570] usbcore: registered new interface driver rndis_host
[   26.114382] usbcore: registered new interface driver sierra
[   26.120223] usbserial: USB Serial support registered for Sierra USB modem
[   26.136802] usbcore: registered new interface driver sierra_net
[   26.166551] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information.
[   26.174709] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
[   26.265545] ath10k 5.15 driver, optimized for CT firmware, probing pci device: 0x56.
[   26.293259] ath10k_pci 0000:00:00.0: enabling device (0000 -> 0002)
[   26.300031] ath10k_pci 0000:00:00.0: pci irq legacy oper_irq_mode 1 irq_mode 0 reset_mode 0
[   33.563254] ath10k_pci 0000:00:00.0: Failed to find firmware-N.bin (N between 2 and 6) from ath10k/QCA9888/hw2.0: -12
[   33.574262] ath10k_pci 0000:00:00.0: could not fetch firmware files (-12)
[   33.581274] ath10k_pci 0000:00:00.0: could not probe fw (-12)
[   33.664657] usbcore: registered new interface driver cdc_mbim
[   33.690531] usbcore: registered new interface driver option
[   33.696425] usbserial: USB Serial support registered for GSM modem (1-port)
[   33.704127] option 1-1:1.0: GSM modem (1-port) converter detected
[   33.710658] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0
[   33.718187] option 1-1:1.1: GSM modem (1-port) converter detected
[   33.724765] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1
[   33.732313] option 1-1:1.2: GSM modem (1-port) converter detected
[   33.738853] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB2
[   33.817344] usbcore: registered new interface driver qcserial
[   33.823409] usbserial: USB Serial support registered for Qualcomm USB modem
[   33.894782] ieee80211 phy1: Atheros AR9561 Rev:0 mem=0xb8100000, irq=2
[   33.935716] kmodloader: done loading kernel modules from /etc/modules.d/*
[   61.517804] eth0: link up (1000Mbps/Full duplex)
[   61.535060] br-lan: port 1(eth0.1) entered blocking state
[   61.540775] br-lan: port 1(eth0.1) entered disabled state
[   61.546689] device eth0.1 entered promiscuous mode
[   61.551643] device eth0 entered promiscuous mode
[   61.560094] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   61.600120] br-lan: port 1(eth0.1) entered blocking state
[   61.605756] br-lan: port 1(eth0.1) entered forwarding state
[   62.850877] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   70.258911] br-lan: port 2(wlan1) entered blocking state
[   70.264541] br-lan: port 2(wlan1) entered disabled state
[   70.270350] device wlan1 entered promiscuous mode
[   70.398552] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[   70.405356] br-lan: port 2(wlan1) entered blocking state
[   70.410844] br-lan: port 2(wlan1) entered forwarding state

        Interface wlan1
                ifindex 9
                wdev 0x100000002
                addr fc:2d:5e:c2:17:f8
                ssid OpenWrt
                type AP
                channel 1 (2412 MHz), width: 20 MHz, center1: 2412 MHz
                txpower 20.00 dBm
                multicast TXQ:
                        qsz-byt qsz-pkt flows   drops   marks   overlmt hashcol tx-bytes        tx-packets
                        0       0       373     0       0       0       0       95361           373
phy#0
        Interface wlan0
                ifindex 10
                wdev 0x2
                addr fc:2d:5e:c2:17:f9
                ssid OpenWrt5
                type AP
                channel 36 (5180 MHz), width: 80 MHz, center1: 5210 MHz
                txpower 23.00 dBm
                multicast TXQ:
                        qsz-byt qsz-pkt flows   drops   marks   overlmt hashcol tx-bytes        tx-packets
                        0       0       0       0       0       0       0       0               0