I'll check these logs tomorrow - now I'm out of access to all that crap. If uart does not work for you, there is no problem with linux machine with inserted modem and uart connected to it. I just need to read how to put the console and gui in linux and I will put you on the public IP. On the copy, apart from Linux, nothing else is needed, so even if a guest hacks him, he will see at most our dead man (modem);)

I'd need to finally sign up for it, but in general I'm positive for that.
In the meantime, here is my setup to connect the serial console to the modem:
https://imgur.com/a/on04nsX

I reused the 1.8V SPI-flash adapter as mentioned earlier, as level shifter, together with standard USB-serial adapter. And an USB full-speed galvanic isolator for extra safety. I have yet to try flashing again, as there is no shell spawned on my unit on ttyHSL0, will come back to that in at most a few days.

Pinout is, with regards to the USB-serial adapter:
2: RX
4: GND
5: TX
8: VCC.

And it's the same both on input connector as on the programmer socket, which goes towards the modem. Obviously, no need to connect pin 8 to the modem - only 2 to modem TX, 4 to GND, 5 to modem RX.

Blue Kynar wire on the modem is routed to the reset pin, by banging it randomly against the ground I can force modem to enter EDL mode either by PBL or by SBL1, usually at random.

Z dużej litery dmesg na pewno nie zadziała

Miało być ...kmsg , a nie ...ksmg

no i daj:
ls /var/log
później ew cat z tych plików ,jak kolega @stich86 chciał

Dziękuję za poprawki już działam

Boże te logi sa gorsze od openwrt:

root@mdm9650:~# dmesg
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 3.18.31 (scl@scl_xa242_062) (gcc version 4.9.2 (GCC) ) #1 PREEMPT Sat Nov 2 07:45:57 CST 2019
[    0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c53c7d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine model: Qualcomm Technologies, Inc. MDM 9650 v1.1 MTP (NAND)
[    0.000000] Reserved memory: reserved region for node 'peripheral2_region@0x87d00000': base 0x87d00000, size 3 MiB
[    0.000000] Reserved memory: reserved region for node 'mss_region@88000000': base 0x88000000, size 110 MiB
[    0.000000] Removed memory: created DMA memory pool at 0x87d00000, size 3 MiB
[    0.000000] Reserved memory: initialized node peripheral2_region@0x87d00000, compatible id removed-dma-pool
[    0.000000] Removed memory: created DMA memory pool at 0x88000000, size 110 MiB
[    0.000000] Reserved memory: initialized node mss_region@88000000, compatible id removed-dma-pool
[    0.000000] Reserved memory: allocated memory for 'audio_region@0' node: base 0x8fc00000, size 4 MiB
[    0.000000] Reserved memory: created CMA memory pool at 0x8fc00000, size 4 MiB
[    0.000000] Reserved memory: initialized node audio_region@0, compatible id shared-dma-pool
[    0.000000] cma: Reserved 12 MiB at 0x8f000000
[    0.000000] Memory policy: Data cache writeback
[    0.000000] On node 0 totalpages: 36608
[    0.000000] free_area_init_node: node 0, pgdat c0df1698, node_mem_map c7ac0000
[    0.000000]   Normal zone: 576 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 36608 pages, LIFO batch:7
[    0.000000] CPU: All CPU(s) started in SVC mode.
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 36032
[    0.000000] Kernel command line: noinitrd  rw console=ttyHSL0,115200,n8 androidboot.hardware=qcom ehci-hcd.park=3 msm_rtb.filter=0x37 lpm_levels.sleep_disabled=1  earlycon=msm_hsl_uart,0x78b1000  androidboot.serialno=100caf6f androidboot.authorized_kernel=true androidboot.baseband=msm rootfstype=ubifs rootflags=bulk_read root=ubi0:rootfs ubi.mtd=16
[    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Memory: 111872K/146432K available (9286K kernel code, 883K rwdata, 4004K rodata, 344K init, 1604K bss, 34560K reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xd0800000 - 0xff000000   ( 744 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xd0000000   ( 256 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0d02c78   (13292 kB)
[    0.000000]       .init : 0xc0d03000 - 0xc0d5920c   ( 345 kB)
[    0.000000]       .data : 0xc0d5a000 - 0xc0e36c04   ( 884 kB)
[    0.000000]        .bss : 0xc0e36cc8 - 0xc0fc7f5c   (1605 kB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] GIC CPU mask not found - kernel will fail to boot.
[    0.000000] GIC CPU mask not found - kernel will fail to boot.
[    0.000000] mpm_init_irq_domain(): Cannot find irq controller for qcom,gpio-parent
[    0.000000] MPM 1 irq mapping errored -517
[    0.000000] Architected mmio timer(s) running at 19.20MHz (virt).
[    0.000007] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 3579139424256ns
[    0.000019] Switching to timer-based delay loop, resolution 52ns
[    0.000033] Switched to clocksource arch_mem_counter
[    0.000446] Console: colour dummy device 80x30
[    0.000460] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=192000)
[    0.000472] pid_max: default: 32768 minimum: 301
[    0.000543] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000554] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000950] Initializing cgroup subsys freezer
[    0.000967] Initializing cgroup subsys debug
[    0.000991] CPU: Testing write buffer coherency: ok
[    0.001227] Setting up static identity map for 0x808db800 - 0x808db858
[    0.002008]
[    0.002008] **********************************************************
[    0.002022] **   NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE   **
[    0.002028] **                                                      **
[    0.002035] ** trace_printk() being used. Allocating extra memory.  **
[    0.002041] **                                                      **
[    0.002047] ** This means that this is a DEBUG kernel and it is     **
[    0.002053] ** unsafe for produciton use.                           **
[    0.002060] **                                                      **
[    0.002066] ** If you see this message and you are not debugging    **
[    0.002072] ** the kernel, report this immediately to your vendor!  **
[    0.002079] **                                                      **
[    0.002085] **   NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE   **
[    0.002091] **********************************************************
[    0.020639] MSM Memory Dump base table set up
[    0.020668] MSM Memory Dump apps data table set up
[    0.023345] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[    0.024891] pinctrl core: initialized pinctrl subsystem
[    0.025167] regulator-dummy: no parameters
[    0.044939] NET: Registered protocol family 16
[    0.046157] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.070091] cpuidle: using governor ladder
[    0.100084] cpuidle: using governor menu
[    0.130083] cpuidle: using governor qcom
[    0.132747] irq: no irq domain found for /soc/pinctrl@1000000 !
[    0.136838] platform 4080000.qcom,mss: assigned reserved memory node mss_region@88000000
[    0.139178] msm_watchdog b017000.qcom,wdt: wdog absent resource not present
[    0.139405] msm_watchdog b017000.qcom,wdt: MSM Watchdog Initialized
[    0.140022] irq: no irq domain found for /soc/pinctrl@1000000 !
[    0.141141] spmi_pmic_arb 200f000.qcom,spmi: PMIC Arb Version-2 0x20010000
[    0.146060] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[    0.146074] hw-breakpoint: maximum watchpoint size is 8 bytes.
[    0.146732] gpiochip_add: registered GPIOs 0 to 99 on device: 1000000.pinctrl
[    0.146748] GPIO chip 1000000.pinctrl: created GPIO range 0->99 ==> 1000000.pinctrl PIN 0->99
[    0.147183] __of_mpm_init(): MPM driver mapping exists
[    0.147505] msm_rpm_glink_dt_parse: qcom,rpm-glink compatible not matches
[    0.147516] msm_rpm_dev_probe: APSS-RPM communication over SMD
[    0.147525] smd_open() before smd_init()
[    0.148013] msm_mpm_dev_probe(): Cannot get clk resource for XO: -517
[    0.149572] smd_channel_probe_now: allocation table not initialized
[    0.152260] glink_rpm_native_probe: TOC id -1185813237 is not valid
[    0.155081] sps:sps is ready.
[    0.155704] exit: IPA_USB init success!
[    0.157099] msm_rpm_glink_dt_parse: qcom,rpm-glink compatible not matches
[    0.157112] msm_rpm_dev_probe: APSS-RPM communication over SMD
[    0.157781] pmd9650_s1: 800 mV normal idle
[    0.158246] pmd9650_s2: 1256 mV normal idle
[    0.158676] pmd9650_s3: 1024 mV normal idle
[    0.159110] pmd9650_s4: 1856 mV normal idle
[    0.159547] pmd9650_s5_level: 0 <--> 0 mV at 0 mV normal idle
[    0.159866] pmd9650_s5_level_ao: 0 <--> 0 mV at 0 mV normal idle
[    0.160303] pmd9650_s5_floor_level: 0 <--> 0 mV at 0 mV normal idle
[    0.160744] pmd9650_l1: 1224 mV normal idle
[    0.161189] pmd9650_l2: 1200 mV normal idle
[    0.161619] pmd9650_l3: 1000 mV normal idle
[    0.162061] pmd9650_l4: 928 mV normal idle
[    0.162512] pmd9650_l5: 1800 mV normal idle
[    0.162950] pmd9650_l6: 1800 mV normal idle
[    0.163404] pmd9650_l7: 1800 <--> 2848 mV at 1800 mV normal idle
[    0.163845] pmd9650_l8: 1000 mV normal idle
[    0.164305] pmd9650_l9_level: 0 <--> 0 mV at 0 mV normal idle
[    0.164745] pmd9650_l10: 3088 mV normal idle
[    0.165161] pmd9650_l11: 1800 <--> 2848 mV at 1800 mV normal idle
[    0.165584] pmd9650_l12: 2704 mV normal idle
[    0.166003] pmd9650_l13: 1800 <--> 2848 mV at 1800 mV normal idle
[    0.166165] msm_mpm_dev_probe(): Cannot get clk resource for XO: -517
[    0.171609] qcom,gcc-9650 1800000.qcom,gcc: Registered RPM clocks.
[    0.173435] qcom,gcc-9650 1800000.qcom,gcc: Registered GCC clocks.
[    0.173693] clock-a7 b010008.qcom,clock-a7: No speed/PVS binning available. Defaulting to 0!
[    0.173742] a7ssmux: set OPP pair(200000000 Hz: 64 uV) on cpu0
[    0.173762] a7ssmux: set OPP pair(1286400000 Hz: 384 uV) on cpu0
[    0.221187] gpiochip_find_base: found new base at 1018
[    0.221296] gpiochip_add: registered GPIOs 1018 to 1023 on device: pmd9650-gpio
[    0.221680] qcom,qpnp-pin qpnp-pin-3: qpnp_pin_probe: gpio_chip registered between 1018-1023
[    0.222283] KPI: Bootloader start count = 29032
[    0.222293] KPI: Bootloader end count = 65535
[    0.222301] KPI: Bootloader display count = 2254737157
[    0.222307] KPI: Bootloader load kernel count = 27280
[    0.222315] KPI: Kernel MPM timestamp = 82749
[    0.222322] KPI: Kernel MPM Clock frequency = 32768
[    0.222343] socinfo_print: v0.10, id=283, ver=1.1, raw_id=50, raw_ver=1, hw_plat=8, hw_plat_ver=65536
[    0.222343]  accessory_chip=0, hw_plat_subtype=0, pmic_model=65551, pmic_die_revision=131072 foundry_id=3 serial_number=269266799
[    0.222584] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/soc/codec_buck_vreg[0]'
[    0.222716] codec_1.8v: no parameters
[    0.222859] of_get_named_gpiod_flags: parsed 'gpio' property of node '/soc/rome_vreg[0]' - status (0)
[    0.222984] rome_vreg: no parameters
[    0.223084] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/soc/sdc_vreg[0]'
[    0.223171] sdc_vreg: no parameters
[    0.223434] vgaarb: loaded
[    0.223678] SCSI subsystem initialized
[    0.223909] usbcore: registered new interface driver usbfs
[    0.223961] usbcore: registered new interface driver hub
[    0.224084] usbcore: registered new device driver usb
[    0.224677] i2c-msm-v2 78b7000.i2c: probing driver i2c-msm-v2
[    0.224745] AXI: msm_bus_scale_register_client(): msm_bus_scale_register_client: Bus driver not ready.
[    0.224757] i2c-msm-v2 78b7000.i2c: msm_bus_scale_register_client(mstr-id:86):0 (not a problem)
[    0.225128] irq: no irq domain found for /soc/wcd9xxx-irq !
[    0.227041] (NULL device *): zte-power: qpnp boot reason: 0x80, 0x0, 0x0, 0x0
[    0.227056] (NULL device *): zte-power: boot status: event 1, poff 0x0, pon 0xaa
[    0.227064] (NULL device *): zte-power: boot status: charger 0, battery 0, vbat 0
[    0.227073] (NULL device *): zte-power: zte boot reason: 0xaa, 0x1
[    0.227080] (NULL device *): zte-power: zte boot lcd id: 0x0
[    0.227091] power zte_power: zte-power: zte_power_get_boot_reason: 1
[    0.227148] of_get_named_gpiod_flags: parsed 'power-board' property of node '/soc/zte_power[0]' - status (0)
[    0.227177] power zte_power: zte-power: gpio-power-board[id-0] 21, valid 0, dir 0, val 1
[    0.227188] of_get_named_gpiod_flags: can't parse 'power-usb' property of node '/soc/zte_power[0]'
[    0.227216] of_get_named_gpiod_flags: parsed 'power-slic' property of node '/soc/zte_power[0]' - status (0)
[    0.227237] power zte_power: zte-power: gpio-power-slic[id-2] 83, valid 0, dir 0, val 1
[    0.227248] of_get_named_gpiod_flags: can't parse 'pmu-gpio-2' property of node '/soc/zte_power[0]'
[    0.227258] of_get_named_gpiod_flags: can't parse 'pmu-gpio-6' property of node '/soc/zte_power[0]'
[    0.227267] of_get_named_gpiod_flags: can't parse 'pmu-gpio-3' property of node '/soc/zte_power[0]'
[    0.227276] of_get_named_gpiod_flags: can't parse 'mdm-gpio-38' property of node '/soc/zte_power[0]'
[    0.227289] power zte_power: zte-power: gpio-21 = 1
[    0.227299] power zte_power: zte-power: gpio-83 always on
[    0.227312] power zte_power: zte-power: attr-battery-discharge[id-40] = 1
[    0.227323] power zte_power: zte-power: attr-battery-full-condition[id-41] = 1
[    0.227339] power zte_power: zte-power: string-percent-file[id-51] is '/cache/battery_percent'
[    0.227350] power zte_power: zte-power: string-rtc-device[id-52] is 'rtc0'
[    0.227359] zte_bsp_netlink_register: module 0
[    0.227368] power zte_power: zte-power: success to creat zte_power device
[    0.227526] (NULL device *): zte-power: zte_power_init done
[    0.228012] cpufreq: driver msm up and running
[    0.228495] platform soc:qcom,ion:qcom,ion-heap@28: assigned reserved memory node audio_region@0
[    0.228748] ION heap system created
[    0.228909] ION heap audio created at 0x8fc00000 with size 400000
[    0.229132] msm_bus_fabric_init_driver
[    0.229317] msm_bus_device 580000.ad-hoc-bus: Coresight support absent for bus: 0
[    0.229370] msm_bus_device 580000.ad-hoc-bus: Coresight support absent for bus: 4096
[    0.229417] msm_bus_device 580000.ad-hoc-bus: Coresight support absent for bus: 1024
[    0.236125] qcom,qpnp-power-on qpnp-power-on-1: PMIC@SID0 Power-on reason: Triggered from KPD (power key press) and 'cold' boot
[    0.236151] qcom,qpnp-power-on qpnp-power-on-1: PMIC@SID0: Unknown power-off reason
[    0.236360] input: qpnp_pon as /devices/virtual/input/input0
[    0.236989] PMIC@SID0: PMD9655 v2.0 options: 0, 0, 0, 0
[    0.237514] of_get_named_gpiod_flags: parsed 'gpios' property of node '/soc/qcom,ipa@07B00000/qcom,smp2pgpio_map_ipa_1_out[0]' - status (-517)
[    0.237708] of_get_named_gpiod_flags: parsed 'gpios' property of node '/soc/qcom,ipa@07B00000/qcom,smp2pgpio_map_ipa_1_in[0]' - status (-517)
[    0.238397] ipa ipa3_uc_state_check:302 uC interface not initialized
[    0.242939] of_get_named_gpiod_flags: parsed 'gpios' property of node '/soc/qcom,ipa@07B00000/qcom,smp2pgpio_map_ipa_1_out[0]' - status (-517)
[    0.243019] of_get_named_gpiod_flags: parsed 'gpios' property of node '/soc/qcom,ipa@07B00000/qcom,smp2pgpio_map_ipa_1_in[0]' - status (-517)
[    0.243254] gdsc_pcie: no parameters
[    0.243450] gdsc_usb30: no parameters
[    0.244037] zte_bsp_netlink done
[    0.244117] Advanced Linux Sound Architecture Driver Initialized.
[    0.244874] cfg80211: Calling CRDA to update world regulatory domain
[    0.244903] cfg80211: World regulatory domain updated:
[    0.244911] cfg80211:  DFS Master region: unset
[    0.244918] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[    0.244929] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[    0.244938] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[    0.244947] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[    0.244956] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[    0.244965] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[    0.244973] cfg80211:   (5490000 KHz - 5710000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[    0.244982] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[    0.244991] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[    0.245239] pcie:pcie_init.
[    0.247113] 80000.qcom,pcie supply vreg-3.3 not found, using dummy regulator
[    0.247267] 80000.qcom,pcie supply vreg-cx not found, using dummy regulator
[    0.247351] 80000.qcom,pcie supply gdsc-smmu not found, using dummy regulator
[    0.247380] of_get_named_gpiod_flags: can't parse 'perst-gpio' property of node '/soc/qcom,pcie@80000[0]'
[    0.247403] msm_pcie_get_resources: Could not get required GPIO perst-gpio
[    0.247438] msm_pcie_probe: PCIe: Driver probe failed for RC0:-2
[    0.247532] mdm9650-pinctrl 1000000.pinctrl: not freeing pin 65 (GPIO_65) as part of deactivating group gpio65 - it is already used for some other setting
[    0.247553] pci-msm: probe of 80000.qcom,pcie failed with error -2
[    0.247940] of_get_named_gpiod_flags: parsed 'gpios' property of node '/soc/qcom,ipa@07B00000/qcom,smp2pgpio_map_ipa_1_out[0]' - status (-517)
[    0.248059] of_get_named_gpiod_flags: parsed 'gpios' property of node '/soc/qcom,ipa@07B00000/qcom,smp2pgpio_map_ipa_1_in[0]' - status (-517)
[    0.248635] Switched to clocksource arch_mem_counter
[    0.268422] NET: Registered protocol family 2
[    0.268965] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[    0.268992] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[    0.269013] TCP: Hash tables configured (established 2048 bind 2048)
[    0.269052] TCP: reno registered
[    0.269064] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.269079] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.269201] NET: Registered protocol family 1
[    0.269237] PCI: CLS 0 bytes, default 64
[    0.269426] of_get_named_gpiod_flags: parsed 'gpios' property of node '/soc/qcom,ipa@07B00000/qcom,smp2pgpio_map_ipa_1_out[0]' - status (-517)
[    0.269548] of_get_named_gpiod_flags: parsed 'gpios' property of node '/soc/qcom,ipa@07B00000/qcom,smp2pgpio_map_ipa_1_in[0]' - status (-517)
[    0.271205] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.278483] msgmni has been set to 250
[    0.279470] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
[    0.279489] io scheduler noop registered
[    0.279502] io scheduler deadline registered
[    0.279528] io scheduler cfq registered (default)
[    0.279611] gpiochip_find_base: found new base at 986
[    0.279705] gpiochip_add: registered GPIOs 986 to 1017 on device: smp2p
[    0.279830] gpiochip_find_base: found new base at 954
[    0.279908] gpiochip_add: registered GPIOs 954 to 985 on device: smp2p
[    0.279940] gpiochip_find_base: found new base at 922
[    0.280012] gpiochip_add: registered GPIOs 922 to 953 on device: smp2p
[    0.280195] gpiochip_find_base: found new base at 890
[    0.280282] gpiochip_add: registered GPIOs 890 to 921 on device: smp2p
[    0.280314] gpiochip_find_base: found new base at 858
[    0.280389] gpiochip_add: registered GPIOs 858 to 889 on device: slave-kernel
[    0.280480] gpiochip_find_base: found new base at 858
[    0.280554] gpiochip_add: registered GPIOs 858 to 889 on device: master-kernel
[    0.280627] gpiochip_find_base: found new base at 858
[    0.280699] gpiochip_add: registered GPIOs 858 to 889 on device: ipa
[    0.280769] gpiochip_find_base: found new base at 858
[    0.280841] gpiochip_add: registered GPIOs 858 to 889 on device: ipa
[    0.284587] apr_tal_link_state_cb: edge[mpss] link state[0]
[    0.284603] apr_tal_link_state_cb: edge[lpass] link state[0]
[    0.286340] msm_rpm_log_probe: OK
[    0.288490] pil-q6v5-mss 4080000.qcom,mss: Failed to find the pas_id.
[    0.288562] of_get_named_gpiod_flags: parsed 'qcom,gpio-proxy-unvote' property of node '/soc/qcom,mss@4080000[0]' - status (-517)
[    0.289410] of_get_named_gpiod_flags: can't parse 'qcom,tx-gpio' property of node '/soc/uart@78B0000[0]'
[    0.289422] uart_tx_gpio is not available
[    0.289432] of_get_named_gpiod_flags: can't parse 'qcom,rx-gpio' property of node '/soc/uart@78B0000[0]'
[    0.289438] uart_rx_gpio is not available
[    0.289447] of_get_named_gpiod_flags: can't parse 'qcom,cts-gpio' property of node '/soc/uart@78B0000[0]'
[    0.289454] uart_cts_gpio is not available
[    0.289463] of_get_named_gpiod_flags: can't parse 'qcom,rfr-gpio' property of node '/soc/uart@78B0000[0]'
[    0.289469] uart_rfr_gpio is not available
[    0.289974] sps: BAM device 0x07884000 is not registered yet.
[    0.290284] sps:BAM 0x07884000 is registered.
[    0.292837] 78b0000.uart: ttyHS0 at MMIO 0x78b0000 (irq = 21, base_baud = 460800) is a MSM HS UART
[    0.295294] msm_serial_hs module loaded
[    0.308080] brd: module loaded
[    0.310422] loop: module loaded
[    0.311977] qcom,qpnp-misc qpnp-misc-2: probe successful
[    0.312080] mashaofeng add for aw9523b init enter
[    0.312161] of_get_named_gpiod_flags: parsed 'shdn_gpio' property of node '/soc/i2c@78B7000/aw9523@5b[0]' - status (0)
[    0.312172] aw9523 reset gpio 83
[    0.312307] i2c-msm-v2 78b7000.i2c: msm_bus_scale_register_client(mstr-id:86):0x4 (ok)
[    0.312478] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:1 tx:1) mode:FIFO slv_addr:0x5b MSTR_STS:0x0d1300c8 OPER:0x00000010
[    0.312535] AW9523 not connected
[    0.312723] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:1 tx:1) mode:FIFO slv_addr:0x5b MSTR_STS:0x0d1300c8 OPER:0x00000010
[    0.312835] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x5b MSTR_STS:0x0d1300c8 OPER:0x00000090
[    0.312880] aw9523b_probe done: create aw9523b-0
[    0.312917] i2c-core: driver [aw9523b] using legacy suspend method
[    0.312925] i2c-core: driver [aw9523b] using legacy resume method
[    0.312933] add aw9523b i2c driver
[    0.313073] SCSI Media Changer driver v0.25
[    0.317861] sps: BAM device 0x07984000 is not registered yet.
[    0.318076] sps:BAM 0x07984000 is registered.
[    0.318094] msm_nand_bam_init: msm_nand_bam_init: BAM device registered: bam_handle 0xc69f5000
[    0.318328] sps:BAM 0x07984000 (va:0xd0aa0000) enabled: ver:0x19, number of pipes:7
[    0.320833] msm_nand_parse_smem_ptable: Parsing partition table info from SMEM
[    0.320872] msm_nand_parse_smem_ptable: SMEM partition table found: ver: 4 len: 17
[    0.320896] msm_nand_version_check: nand_major:1, nand_minor:5, qpic_major:1, qpic_minor:5
[    0.320928] zhao.wl g_zte_flash_id = 0x2690ac2c
[    0.320939] msm_nand_scan: NAND Id: 0x2690ac2c Buswidth: 8Bits Density: 512 MByte
[    0.320947] msm_nand_scan: pagesize: 4096 Erasesize: 262144 oobsize: 224 (in Bytes)
[    0.320954] msm_nand_scan: BCH ECC: 8 Bit
[    0.320967] msm_nand_scan: CFG0: 0x290409c0,           CFG1: 0x08045d5c
[    0.320967]             RAWCFG0: 0x2b8401c0,        RAWCFG1: 0x0005055d
[    0.320967]           ECCBUFCFG: 0x00000203,      ECCBCHCFG: 0x42040d10
[    0.320967]           RAWECCCFG: 0x42000d11, BAD BLOCK BYTE: 0x00000175
[    0.321001] Creating 17 MTD partitions on "7980000.nand":
[    0.321013] 0x000000000000-0x000000280000 : "sbl"
[    0.321655] 0x000000280000-0x000000500000 : "mibib"
[    0.322159] 0x000000500000-0x000001000000 : "efs2"
[    0.322670] 0x000001000000-0x000001380000 : "tz"
[    0.323187] 0x000001380000-0x0000016c0000 : "rpm"
[    0.323701] 0x0000016c0000-0x0000021c0000 : "efsbak"
[    0.324230] 0x0000021c0000-0x0000022c0000 : "aboot"
[    0.324776] 0x0000022c0000-0x0000031c0000 : "boot"
[    0.325326] 0x0000031c0000-0x000003240000 : "scrub"
[    0.325882] 0x000003240000-0x000007940000 : "modem"
[    0.326380] 0x000007940000-0x000007ac0000 : "misc"
[    0.326887] 0x000007ac0000-0x0000089c0000 : "recovery"
[    0.327388] 0x0000089c0000-0x000008b40000 : "fota"
[    0.327904] 0x000008b40000-0x00000b340000 : "recoveryfs"
[    0.328436] 0x00000b340000-0x00000c900000 : "ztefile"
[    0.328985] 0x00000c900000-0x000015a00000 : "zterw"
[    0.329544] 0x000015a00000-0x000020000000 : "system"
[    0.330198] msm_nand_probe: NANDc phys addr 0x7980000, BAM phys addr 0x7984000, BAM IRQ 37
[    0.330209] msm_nand_probe: Allocated DMA buffer at virt_addr 0xcf046000, phys_addr 0x8f046000
[    0.331080] of_get_named_gpiod_flags: can't parse 'qcom,gpio-clk' property of node '/soc/spi@78B5000[0]'
[    0.331095] of_get_named_gpiod_flags: can't parse 'qcom,gpio-miso' property of node '/soc/spi@78B5000[0]'
[    0.331105] of_get_named_gpiod_flags: can't parse 'qcom,gpio-mosi' property of node '/soc/spi@78B5000[0]'
[    0.331114] of_get_named_gpiod_flags: can't parse 'qcom,gpio-cs0' property of node '/soc/spi@78B5000[0]'
[    0.331124] of_get_named_gpiod_flags: can't parse 'qcom,gpio-cs1' property of node '/soc/spi@78B5000[0]'
[    0.331133] of_get_named_gpiod_flags: can't parse 'qcom,gpio-cs2' property of node '/soc/spi@78B5000[0]'
[    0.331142] of_get_named_gpiod_flags: can't parse 'qcom,gpio-cs3' property of node '/soc/spi@78B5000[0]'
[    0.332365] sps:BAM 0x07884000 (va:0xd0b40000) enabled: ver:0x19, number of pipes:16
[    0.332936] tun: Universal TUN/TAP device driver, 1.6
[    0.332947] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    0.333068] PPP generic driver version 2.4.2
[    0.339598] of_get_named_gpiod_flags: parsed 'wlan-en-gpio' property of node '/soc/qcom,cnss[0]' - status (0)
[    0.339733] cnss_pinctrl_init: Can not get active pin state!
[    0.350121] cnss_probe: Failed to enable PCIe RC0!
[    0.371040] usbcore: registered new interface driver asix
[    0.371113] usbcore: registered new interface driver ax88179_178a
[    0.371161] usbcore: registered new interface driver cdc_ether
[    0.371221] usbcore: registered new interface driver smsc75xx
[    0.371279] usbcore: registered new interface driver smsc95xx
[    0.371324] usbcore: registered new interface driver net1080
[    0.371369] usbcore: registered new interface driver cdc_subset
[    0.371420] usbcore: registered new interface driver zaurus
[    0.371681] usbcore: registered new interface driver cdc_ncm
[    0.373987] msm_sharedmem: sharedmem_register_qmi: qmi init successful
[    0.376644] of_get_named_gpiod_flags: can't parse 'qcom,ext-hub-reset-gpio' property of node '/soc/ssusb@8a00000[0]'
[    0.376867] power zte_power: zte-power: power supply usb registered
[    0.379529] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.379761] ehci-pci: EHCI PCI platform driver
[    0.379823] ehci-msm: Qualcomm On-Chip EHCI Host Controller
[    0.380242] usbcore: registered new interface driver cdc_acm
[    0.380252] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[    0.380318] usbcore: registered new interface driver usb-storage
[    0.380359] usbcore: registered new interface driver ums-alauda
[    0.380398] usbcore: registered new interface driver ums-cypress
[    0.380444] usbcore: registered new interface driver ums-datafab
[    0.380484] usbcore: registered new interface driver ums-freecom
[    0.380524] usbcore: registered new interface driver ums-isd200
[    0.380564] usbcore: registered new interface driver ums-jumpshot
[    0.380602] usbcore: registered new interface driver ums-karma
[    0.380640] usbcore: registered new interface driver ums-onetouch
[    0.380679] usbcore: registered new interface driver ums-sddr09
[    0.380726] usbcore: registered new interface driver ums-sddr55
[    0.380766] usbcore: registered new interface driver ums-usbat
[    0.381599] gbridge_init: gbridge_init successs.
[    0.382292] qcom,qpnp-rtc qpnp-rtc-5: rtc core: registered qpnp_rtc as rtc0
[    0.382448] i2c /dev entries driver
[    0.383005] unable to find DT imem DLOAD mode node
[    0.383263] unable to find DT imem EDLOAD mode node
[    0.383492] unable to find DT imem dload-type node
[    0.384433] qpnp_vadc_read: Error reading vadc_hc channel 78
[    0.384449] thermal thermal_zone0: failed to read out thermal zone 0
[    0.384714] qpnp_vadc_read: Error reading vadc_hc channel 79
[    0.384727] thermal thermal_zone1: failed to read out thermal zone 1
[    0.384982] qpnp_vadc_read: Error reading vadc_hc channel 76
[    0.384994] thermal thermal_zone2: failed to read out thermal zone 2
[    0.385238] qpnp_vadc_read: Error reading vadc_hc channel 83
[    0.385249] thermal thermal_zone3: failed to read out thermal zone 3
[    0.385502] qpnp_vadc_read: Error reading vadc_hc channel 77
[    0.385513] thermal thermal_zone4: failed to read out thermal zone 4
[    0.387813] sdhci: Secure Digital Host Controller Interface driver
[    0.387824] sdhci: Copyright(c) Pierre Ossman
[    0.387836] sdhci-pltfm: SDHCI platform and OF driver helper
[    0.388212] guotao:enter the aw9106b_led_probe for the test.
[    0.388224] guotao:enter the platform_set_drvdata for the test.
[    0.388234] MSF change bat and power  light's state
[    0.388234]  guotao:exit the aw9106b_led_probe for the test.
[    0.389258] usbcore: registered new interface driver usbhid
[    0.389267] usbhid: USB HID core driver
[    0.389315] ipa_ut ipa_ut_module_init:960 Loading IPA test module...
[    0.389615] of_get_named_gpiod_flags: can't parse 'qcom,gpio-mode-sel' property of node '/soc/usb_detect[0]'
[    0.390342] sdhci_msm 7824900.sdhci: sdhci_msm_probe: ICE device is not enabled
[    0.390368] of_get_named_gpiod_flags: can't parse 'cd-gpios' property of node '/soc/sdhci@7824000[0]'
[    0.390414] sdhci_msm 7824900.sdhci: no qcom,vdd-voltage-level property
[    0.390425] sdhci_msm 7824900.sdhci: no qcom,vdd-current-level property
[    0.390673] sdhci_msm 7824900.sdhci: sdhci_msm_pm_qos_parse_irq: could not read 2 values for 'qcom,pm-qos-irq-latency'
[    0.390684] sdhci_msm 7824900.sdhci: sdhci_msm_pm_qos_parse: PM QoS voting for IRQ will be disabled
[    0.390708] sdhci_msm 7824900.sdhci: sdhci_msm_pm_qos_parse_latency: invalid number of values for property qcom,pm-qos-cmdq-latency-us: expected=2 actual=1
[    0.390720] sdhci_msm 7824900.sdhci: sdhci_msm_pm_qos_parse_latency: invalid number of values for property qcom,pm-qos-legacy-latency-us: expected=2 actual=1
[    0.390731] sdhci_msm 7824900.sdhci: sdhci_msm_pm_qos_parse: invalid PM QoS latency values. Voting for cpu group will be disabled
[    0.392557] sps:BAM 0x08b04000 is registered.
[    0.394814] devfreq soc:qcom,cpubw: Couldn't update frequency transition information.
[    0.395807] coresight-fuse a601c.fuse: Fuse initialized
[    0.397818] coresight-csr 801000.csr: CSR initialized
[    0.398252] coresight-tmc 828000.tmc: Byte Counter feature enabled
[    0.398461] sps:BAM 0x00884000 is registered.
[    0.398492] coresight-tmc 828000.tmc: invalid cti data
[    0.398675] coresight-tmc 828000.tmc: TMC initialized
[    0.398794] coresight-tmc 827000.tmc: invalid cti data
[    0.398947] coresight-tmc 827000.tmc: TMC initialized
[    0.400532] sdhci_msm 7824900.sdhci: No vmmc regulator found
[    0.400546] sdhci_msm 7824900.sdhci: No vqmmc regulator found
[    0.401023] mmc0: SDHCI controller on 7824900.sdhci [7824900.sdhci] using 32-bit ADMA in legacy mode
[    0.401641] coresight-replicator 826000.replicator: REPLICATOR initialized
[    0.403724] coresight-dbgui 86d000.dbgui: DebugUI capture enabled
[    0.403861] coresight-dbgui 86d000.dbgui: DebugUI initializaed
[    0.404316] coresight-stm 802000.stm: STM initialized
[    0.404666] coresight-hwevent 86c000.hwevent: Hardware Event driver initialized
[    0.405265] coresight-remote-etm soc:modem_etm0: Remote ETM initialized
[    0.405514] coresight-remote-etm soc:rpm_etm0: Remote ETM initialized
[    0.406248] of_get_named_gpiod_flags: parsed 'rst-gpio' property of node '/soc/spi@78B5000/si3217x@0[0]' - status (0)
[    0.406276] of_get_named_gpiod_flags: parsed 'irq-gpio' property of node '/soc/spi@78B5000/si3217x@0[0]' - status (0)
[    0.406290] si3217x spi1.0: irq_gpio is 15, rst_gpio is 14, num_slic is 1
[    0.406404] slic slic-0: Registered slic device 261095424l(249,0)
[    0.406415] si3217x spi1.0: si3217x_spi_probe done
[    0.411387] mdm9650-pinctrl 1000000.pinctrl: pin GPIO_15 already requested by spi1.0; cannot claim for soc:qcom,msm-dai-mi2s:qcom,msm-dai-q6-mi2s-prim
[    0.411404] mdm9650-pinctrl 1000000.pinctrl: pin-15 (soc:qcom,msm-dai-mi2s:qcom,msm-dai-q6-mi2s-prim) status -22
[    0.411416] mdm9650-pinctrl 1000000.pinctrl: could not request pin 15 (GPIO_15) from group gpio15  on device 1000000.pinctrl
[    0.411426] msm-dai-q6-mi2s soc:qcom,msm-dai-mi2s:qcom,msm-dai-q6-mi2s-prim: Error applying setting, reverse things back
[    0.414552] msm_pcm_probe: dev name soc:qcom,msm-voice-host-pcm
[    0.419785] mdm9650-asoc-tasha soc:sound: ASoC: platform (null) not registered
[    0.420011] zte_voip_qos_init start...
[    0.420507] Netfilter messages via NETLINK v0.30.
[    0.420697] nf_conntrack version 0.5.0 (2004 buckets, 8016 max)
[    0.421285] ctnetlink v0.93: registering with nfnetlink.
[    0.421748] ip_set: protocol 6
[    0.422099] ip_tables: (C) 2000-2006 Netfilter Core Team
[    0.422219] arp_tables: (C) 2002 David S. Miller
[    0.422266] TCP: cubic registered
[    0.424150] msm-dwc3 8a00000.ssusb: DWC3 in low power mode
[    0.424613] NET: Registered protocol family 10
[    0.425392] ip6_tables: (C) 2000-2006 Netfilter Core Team
[    0.425564] sit: IPv6 over IPv4 tunneling driver
[    0.426042] NET: Registered protocol family 17
[    0.426137] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    0.426155] Ebtables v2.0 registered
[    0.426671] NET: Registered protocol family 27
[    0.428430] IPC_RTR: pil_vote_load_worker: Failed to load modem
[    0.428472] IPC_RTR: pil_vote_load_worker: Failed to load modem
[    0.428482] IPC_RTR: pil_vote_load_worker: Failed to load modem
[    0.428491] IPC_RTR: pil_vote_load_worker: Failed to load modem
[    0.428499] IPC_RTR: pil_vote_load_worker: Failed to load modem
[    0.428507] IPC_RTR: pil_vote_load_worker: Failed to load modem
[    0.428515] IPC_RTR: pil_vote_load_worker: Failed to load modem
[    0.428524] IPC_RTR: pil_vote_load_worker: Failed to load modem
[    0.428532] IPC_RTR: pil_vote_load_worker: Failed to load modem
[    0.428540] IPC_RTR: pil_vote_load_worker: Failed to load modem
[    0.428548] IPC_RTR: pil_vote_load_worker: Failed to load modem
[    0.428556] IPC_RTR: pil_vote_load_worker: Failed to load modem
[    0.428886] of_get_named_gpiod_flags: parsed 'gpios' property of node '/soc/qcom,ipa@07B00000/qcom,smp2pgpio_map_ipa_1_out[0]' - status (-517)
[    0.429131] of_get_named_gpiod_flags: parsed 'gpios' property of node '/soc/qcom,ipa@07B00000/qcom,smp2pgpio_map_ipa_1_in[0]' - status (-517)
[    0.429305] gpiochip_find_base: found new base at 858
[    0.429406] gpiochip_add: registered GPIOs 858 to 889 on device: slave-kernel
[    0.429615] gpiochip_find_base: found new base at 826
[    0.429704] gpiochip_add: registered GPIOs 826 to 857 on device: master-kernel
[    0.429780] gpiochip_find_base: found new base at 794
[    0.430216] gpiochip_add: registered GPIOs 794 to 825 on device: ipa
[    0.430317] gpiochip_find_base: found new base at 762
[    0.430418] gpiochip_add: registered GPIOs 762 to 793 on device: ipa
[    0.434605] pil-q6v5-mss 4080000.qcom,mss: Failed to find the pas_id.
[    0.434661] of_get_named_gpiod_flags: parsed 'qcom,gpio-proxy-unvote' property of node '/soc/qcom,mss@4080000[0]' - status (0)
[    0.435206] of_get_named_gpiod_flags: parsed 'qcom,gpio-err-fatal' property of node '/soc/qcom,mss@4080000[0]' - status (0)
[    0.435223] of_get_named_gpiod_flags: parsed 'qcom,gpio-err-ready' property of node '/soc/qcom,mss@4080000[0]' - status (0)
[    0.435236] of_get_named_gpiod_flags: parsed 'qcom,gpio-stop-ack' property of node '/soc/qcom,mss@4080000[0]' - status (0)
[    0.435250] of_get_named_gpiod_flags: parsed 'qcom,gpio-force-stop' property of node '/soc/qcom,mss@4080000[0]' - status (0)
[    0.435381] pil-q6v5-mss 4080000.qcom,mss: for modem segments only will be dumped.
[    0.441964] of_get_named_gpiod_flags: parsed 'wlan-en-gpio' property of node '/soc/qcom,cnss[0]' - status (0)
[    0.442111] cnss_pinctrl_init: Can not get active pin state!
[    0.460122] cnss_probe: Failed to enable PCIe RC0!
[    0.486760] msm-pcm-routing soc:qcom,msm-pcm-routing: ASoC: no dapm match for MM_DL5 --> MultiMedia5 --> TERT_MI2S_RX Audio Mixer
[    0.486780] msm-pcm-routing soc:qcom,msm-pcm-routing: ASoC: Failed to add route MM_DL5 -> MultiMedia5 -> TERT_MI2S_RX Audio Mixer
[    0.486835] msm-pcm-routing soc:qcom,msm-pcm-routing: ASoC: no dapm match for MM_DL8 --> MultiMedia8 --> TERT_MI2S_RX Audio Mixer
[    0.486845] msm-pcm-routing soc:qcom,msm-pcm-routing: ASoC: Failed to add route MM_DL8 -> MultiMedia8 -> TERT_MI2S_RX Audio Mixer
[    0.487323] msm-pcm-routing soc:qcom,msm-pcm-routing: ASoC: no dapm match for INT_FM_TX --> INTERNAL_FM_TX --> SEC_MI2S_RX Port Mixer
[    0.487335] msm-pcm-routing soc:qcom,msm-pcm-routing: ASoC: Failed to add route INT_FM_TX -> INTERNAL_FM_TX -> SEC_MI2S_RX Port Mixer
[    0.494330] msm-pcm-routing soc:qcom,msm-pcm-routing: ASoC: no dapm match for VOICEMMODE1_DL --> VoiceMMode1 --> SEC_MI2S_RX_Voice Mixer
[    0.494346] msm-pcm-routing soc:qcom,msm-pcm-routing: ASoC: Failed to add route VOICEMMODE1_DL -> VoiceMMode1 -> SEC_MI2S_RX_Voice Mixer
[    0.494378] msm-pcm-routing soc:qcom,msm-pcm-routing: ASoC: no dapm match for VOICEMMODE2_DL --> VoiceMMode2 --> SEC_MI2S_RX_Voice Mixer
[    0.494388] msm-pcm-routing soc:qcom,msm-pcm-routing: ASoC: Failed to add route VOICEMMODE2_DL -> VoiceMMode2 -> SEC_MI2S_RX_Voice Mixer
[    0.497166] msm-pcm-routing soc:qcom,msm-pcm-routing: ASoC: no source widget found for AUDIO_REF_EC_UL3 MUX
[    0.497179] msm-pcm-routing soc:qcom,msm-pcm-routing: ASoC: Failed to add route AUDIO_REF_EC_UL3 MUX -> direct -> MM_UL3
[    0.501774] msm-pcm-routing soc:qcom,msm-pcm-routing: ASoC: no dapm match for SEC_MI2S_TX --> SEC_MI2S_TX --> SLIMBUS_0_RX Port Mixer
[    0.501788] msm-pcm-routing soc:qcom,msm-pcm-routing: ASoC: Failed to add route SEC_MI2S_TX -> SEC_MI2S_TX -> SLIMBUS_0_RX Port Mixer
[    0.502475] msm-pcm-routing soc:qcom,msm-pcm-routing: ASoC: no dapm match for VOICE2_STUB_DL --> Voice2 Stub --> INTERNAL_BT_SCO_RX_Voice Mixer
[    0.502487] msm-pcm-routing soc:qcom,msm-pcm-routing: ASoC: Failed to add route VOICE2_STUB_DL -> Voice2 Stub -> INTERNAL_BT_SCO_RX_Voice Mixer
[    0.503805] msm-pcm-routing soc:qcom,msm-pcm-routing: ASoC: no sink widget found for SENARY_MI2S_TX
[    0.503817] msm-pcm-routing soc:qcom,msm-pcm-routing: ASoC: Failed to add route BE_IN -> direct -> SENARY_MI2S_TX
[    0.559135] msm-pcm-routing soc:qcom,msm-pcm-routing: ASoC: Failed to create SEC_MI2S_RX Port Mixer debugfs file
[    0.575185] msm-pcm-routing soc:qcom,msm-pcm-routing: ASoC: mux SLIM_0_RX AANC MUX has no paths
[    0.582416] msm-dai-stub-dev soc:qcom,msm-dai-stub:qcom,msm-dai-stub-dtmf-tx: ASoC: no sink widget found for STUB_DTMF_TX
[    0.582435] msm-dai-stub-dev soc:qcom,msm-dai-stub:qcom,msm-dai-stub-dtmf-tx: ASoC: Failed to add route DTMF TX -> direct -> STUB_DTMF_TX
[    0.582485] msm-dai-stub-dev soc:qcom,msm-dai-stub:qcom,msm-dai-stub-host-rx-capture-tx: ASoC: no sink widget found for STUB_HOST_RX_CAPTURE_TX
[    0.582497] msm-dai-stub-dev soc:qcom,msm-dai-stub:qcom,msm-dai-stub-host-rx-capture-tx: ASoC: Failed to add route CS-VOICE HOST RX CAPTURE -> direct -> STUB_HOST_RX_CAPTURE_TX
[    0.582540] msm-dai-stub-dev soc:qcom,msm-dai-stub:qcom,msm-dai-stub-host-rx-playback-rx: ASoC: no source widget found for STUB_HOST_RX_PLAYBACK_RX
[    0.582552] msm-dai-stub-dev soc:qcom,msm-dai-stub:qcom,msm-dai-stub-host-rx-playback-rx: ASoC: Failed to add route STUB_HOST_RX_PLAYBACK_RX -> direct -> CS-VOICE HOST RX PLAYBACK
[    0.582594] msm-dai-stub-dev soc:qcom,msm-dai-stub:qcom,msm-dai-stub-host-tx-capture-tx: ASoC: no sink widget found for STUB_HOST_TX_CAPTURE_TX
[    0.582607] msm-dai-stub-dev soc:qcom,msm-dai-stub:qcom,msm-dai-stub-host-tx-capture-tx: ASoC: Failed to add route CS-VOICE HOST TX CAPTURE -> direct -> STUB_HOST_TX_CAPTURE_TX
[    0.582646] msm-dai-stub-dev soc:qcom,msm-dai-stub:qcom,msm-dai-stub-host-tx-playback-rx: ASoC: no source widget found for STUB_HOST_TX_PLAYBACK_RX
[    0.582658] msm-dai-stub-dev soc:qcom,msm-dai-stub:qcom,msm-dai-stub-host-tx-playback-rx: ASoC: Failed to add route STUB_HOST_TX_PLAYBACK_RX -> direct -> CS-VOICE HOST TX PLAYBACK
[    0.594244] of_get_named_gpiod_flags: parsed 'gpios' property of node '/soc/qcom,ipa@07B00000/qcom,smp2pgpio_map_ipa_1_out[0]' - status (0)
[    0.594361] of_get_named_gpiod_flags: parsed 'gpios' property of node '/soc/qcom,ipa@07B00000/qcom,smp2pgpio_map_ipa_1_in[0]' - status (0)
[    0.594434] ipa ipa3_smp2p_probe:5570 failed to enable irq wake
[    0.600869] of_get_named_gpiod_flags: parsed 'wlan-en-gpio' property of node '/soc/qcom,cnss[0]' - status (0)
[    0.601009] cnss_pinctrl_init: Can not get active pin state!
[    0.620126] cnss_probe: Failed to enable PCIe RC0!
[    0.657390] of_get_named_gpiod_flags: parsed 'wlan-en-gpio' property of node '/soc/qcom,cnss[0]' - status (0)
[    0.657543] cnss_pinctrl_init: Can not get active pin state!
[    0.670153] cnss_probe: Failed to enable PCIe RC0!
[    0.690743] ubi0: attaching mtd16
[    1.295169] ubi0: scanning is finished
[    1.300532] ubi0 warning: print_rsvd_warning: cannot reserve enough PEBs for bad PEB handling, reserved 39, need 40
[    1.301178] ubi0: attached mtd16 (name "system", size 166 MiB)
[    1.301189] ubi0: PEB size: 262144 bytes (256 KiB), LEB size: 253952 bytes
[    1.301198] ubi0: min./max. I/O unit sizes: 4096/4096, sub-page size 4096
[    1.301206] ubi0: VID header offset: 4096 (aligned 4096), data offset: 8192
[    1.301214] ubi0: good PEBs: 664, bad PEBs: 0, corrupted PEBs: 0
[    1.301222] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
[    1.301231] ubi0: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 1058667151
[    1.301240] ubi0: available PEBs: 0, total reserved PEBs: 664, PEBs reserved for bad PEB handling: 39
[    1.301269] RNDIS_IPA module is loaded.
[    1.301298] ZTE: Create usb netlink usb !
[    1.301308] zte_read_usb_config_args_from_q6:  sizeof(ZTE_config_args_s_type) = 628
[    1.301332] enter zte dwnload mode, lose config file
[    1.301340]
[    1.301340] zte_usb_a5_config_init init config because modem is not loaded the ret  is 0
[    1.301453] ubi0: background thread "ubi_bgt0d" started, PID 151
[    1.301486] zte_usb_switch_wq_init: zte_usb_switch_wq_init: start zte usb port switch init
[    1.301610] zte_dif_remove_switch_wq_init: zte_dif_remove_switch_wq_init: start zte dif remove usb port switch init
[    1.301619] init: init: zte init over for usb config
[    1.302186] android_bind: android_bind serial_string = :
[    1.302262] file system registered
[    1.302597] Number of LUNs=8
[    1.302610] Mass Storage Function, version: 2009/09/11
[    1.302620] LUN: removable file: (no medium)
[    1.302635] Number of LUNs=2
[    1.302691] LUN: removable file: (no medium)
[    1.302739] LUN: removable file: (no medium)
[    1.302746] Number of LUNs=2
[    1.303319] android_usb gadget: android_usb ready
[    1.304453] MSF zte_power_key_wq_init: enter=================
[    1.304638] MSF zte_power_key_wq_init: exit >>>>>>>>>>>>>>>>>>>>
[    1.304701] of_get_named_gpiod_flags: parsed 'gpios' property of node '/soc/gpio_keys/wps[0]' - status (0)
[    1.304729] of_get_named_gpiod_flags: parsed 'gpios' property of node '/soc/gpio_keys/power[0]' - status (0)
[    1.304889] gpio-22 (wps-key): gpiod_set_debounce: missing set() or set_debounce() operations
[    1.304950] gpio-50 (power-key): gpiod_set_debounce: missing set() or set_debounce() operations
[    1.305519] input: gpio-keys as /devices/soc:gpio_keys/input/input1
[    1.305537] gpio_keys_gpio_report_event code=115 state=1
[    1.305766] gpio_keys_gpio_report_event code=116 state=0
[    1.305775] zte_power_get_ready:0
[    1.306217] qcom,qpnp-rtc qpnp-rtc-5: setting system clock to 1970-01-01 00:00:03 UTC (3)
[    1.306645] parse_legacy_cluster_params(): Ignoring cluster params
[    1.306676] /soc/qcom,lpm-levels/qcom,pm-cluster@0: No CPU phandle, assuming single cluster
[    1.306702] parse_cpu_levels: idx 1 15002
[    1.306709] parse_cpu_levels: idx 2 7919
[    1.306716] calculate_residency: residency < 0 for LPM
[    1.306722] parse_cpu_levels: idx 2 7300
[    1.306731] calculate_residency: residency < 0 for LPM
[    1.306737] calculate_residency: residency < 0 for LPM
[    1.308827] rmnet_ipa3 started initialization
[    1.309608] qcom,cc-debug-9650 1874000.qcom,cc-debug: Registered debug mux.
[    1.309906] of_get_named_gpiod_flags: parsed 'wlan-en-gpio' property of node '/soc/qcom,cnss[0]' - status (0)
[    1.310118] cnss_pinctrl_init: Can not get active pin state!
[    1.310237] sdc_vreg: disabling
[    1.310267] clock_late_init: Removing enables held for handed-off clocks
[    1.313153] ALSA device list:
[    1.313163]   #0: mdm-tasha-i2s-snd-card
[    1.313265] Warning: unable to open an initial console.
[    1.330128] cnss_probe: Failed to enable PCIe RC0!
[    1.356919] of_get_named_gpiod_flags: parsed 'wlan-en-gpio' property of node '/soc/qcom,cnss[0]' - status (0)
[    1.357061] cnss_pinctrl_init: Can not get active pin state!
[    1.370136] cnss_probe: Failed to enable PCIe RC0!
[    1.400124] UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 155
[    1.510380] UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[    1.510395] UBIFS (ubi0:0): LEB size: 253952 bytes (248 KiB), min./max. I/O unit sizes: 4096 bytes/4096 bytes
[    1.510406] UBIFS (ubi0:0): FS size: 81518592 bytes (77 MiB, 321 LEBs), journal size 9404416 bytes (8 MiB, 38 LEBs)
[    1.510414] UBIFS (ubi0:0): reserved for root: 0 bytes (0 KiB)
[    1.510426] UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID BAB32798-07C2-4758-BB05-2231406C3994, small LPT model
[    1.512739] VFS: Mounted root (ubifs filesystem) on device 0:11.
[    1.513219] Freeing unused kernel memory: 344K (c0d03000 - c0d59000)
[    2.093551] UBIFS (ubi0:0): background thread "ubifs_bgt0_0" stops
[    2.318976] msm-dwc3 8a00000.ssusb: DWC3 exited from low power mode
[    2.344685] ubi1: attaching mtd9
[    2.653044] ubi1: scanning is finished
[    2.658711] ubi1: attached mtd9 (name "modem", size 71 MiB)
[    2.658724] ubi1: PEB size: 262144 bytes (256 KiB), LEB size: 253952 bytes
[    2.658732] ubi1: min./max. I/O unit sizes: 4096/4096, sub-page size 4096
[    2.658740] ubi1: VID header offset: 4096 (aligned 4096), data offset: 8192
[    2.658748] ubi1: good PEBs: 284, bad PEBs: 0, corrupted PEBs: 0
[    2.658756] ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
[    2.658765] ubi1: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 1902903672
[    2.658773] ubi1: available PEBs: 0, total reserved PEBs: 284, PEBs reserved for bad PEB handling: 40
[    2.660858] ubi1: background thread "ubi_bgt1d" started, PID 235
[    2.795137] UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "modem", R/O mode
[    2.795153] UBIFS (ubi1:0): LEB size: 253952 bytes (248 KiB), min./max. I/O unit sizes: 4096 bytes/4096 bytes
[    2.795164] UBIFS (ubi1:0): FS size: 58408960 bytes (55 MiB, 230 LEBs), journal size 9404416 bytes (8 MiB, 38 LEBs)
[    2.795172] UBIFS (ubi1:0): reserved for root: 0 bytes (0 KiB)
[    2.795183] UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID F1C8CDF9-6C55-4E76-AF93-7175639B1430, small LPT model
[    2.810129] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 242
[    2.861891] UBIFS (ubi0:1): recovery needed
[    2.933090] UBIFS (ubi0:1): recovery completed
[    2.933166] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "fwfs"
[    2.933177] UBIFS (ubi0:1): LEB size: 253952 bytes (248 KiB), min./max. I/O unit sizes: 4096 bytes/4096 bytes
[    2.933188] UBIFS (ubi0:1): FS size: 8126464 bytes (7 MiB, 32 LEBs), journal size 2285569 bytes (2 MiB, 9 LEBs)
[    2.933196] UBIFS (ubi0:1): reserved for root: 0 bytes (0 KiB)
[    2.933208] UBIFS (ubi0:1): media format: w4/r0 (latest is w4/r0), UUID EA6867B1-5D35-41C7-96E9-FA2ACE2C3026, small LPT model
[    2.941056] gsi soc:qcom,msm_gsi: gsi_register_device:757 GSI irq is wake enabled 33
[    2.946273] rmnet_ipa3 started initialization
[    2.946288] IPA SSR support = False
[    2.946295] IPA ipa-loaduC = False
[    2.946301] IPA SG support = False
[    2.947972] IPA driver initialization was successful.
[    2.949204] ipa ipa3_uc_state_check:307 uC is not loaded
[    2.953311] rmnet_ipa completed initialization
[    3.116962] UBIFS (ubi0:2): UBIFS: mounted UBI device 0, volume 2, name "ztedata", R/O mode
[    3.116978] UBIFS (ubi0:2): LEB size: 253952 bytes (248 KiB), min./max. I/O unit sizes: 4096 bytes/4096 bytes
[    3.116989] UBIFS (ubi0:2): FS size: 60440576 bytes (57 MiB, 238 LEBs), journal size 8634368 bytes (8 MiB, 34 LEBs)
[    3.116997] UBIFS (ubi0:2): reserved for root: 0 bytes (0 KiB)
[    3.117009] UBIFS (ubi0:2): media format: w4/r0 (latest is w4/r0), UUID 48BDDBE2-3808-4755-8C21-4081E50D519B, small LPT model
[    3.152804] ubi3: attaching mtd15
[    3.290329] Error: Driver 'IPCRTR' is already registered, aborting...
[    3.290341] IPC_RTR: msm_ipc_router_smd_driver_register: Failed to register platform driver [IPCRTR]
[    3.290351] IPC_RTR: msm_ipc_router_smd_driver_register Already driver registered IPCRTR
[    3.290359] IPC_RTR: msm_ipc_router_smd_driver_register Already driver registered IPCRTR
[    3.665494] ubi3: scanning is finished
[    3.671689] ubi3: attached mtd15 (name "zterw", size 145 MiB)
[    3.671702] ubi3: PEB size: 262144 bytes (256 KiB), LEB size: 253952 bytes
[    3.671710] ubi3: min./max. I/O unit sizes: 4096/4096, sub-page size 4096
[    3.671719] ubi3: VID header offset: 4096 (aligned 4096), data offset: 8192
[    3.671726] ubi3: good PEBs: 580, bad PEBs: 0, corrupted PEBs: 0
[    3.671734] ubi3: user volume: 3, internal volumes: 1, max. volumes count: 128
[    3.671743] ubi3: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 2085794730
[    3.671751] ubi3: available PEBs: 0, total reserved PEBs: 580, PEBs reserved for bad PEB handling: 40
[    3.673436] ubi3: background thread "ubi_bgt3d" started, PID 278
[    3.900104] UBIFS (ubi3:0): background thread "ubifs_bgt3_0" started, PID 285
[    3.949787] UBIFS (ubi3:0): recovery needed
[    4.105764] UBIFS (ubi3:0): recovery completed
[    4.105835] UBIFS (ubi3:0): UBIFS: mounted UBI device 3, volume 0, name "etcrwfs"
[    4.105846] UBIFS (ubi3:0): LEB size: 253952 bytes (248 KiB), min./max. I/O unit sizes: 4096 bytes/4096 bytes
[    4.105857] UBIFS (ubi3:0): FS size: 39616512 bytes (37 MiB, 156 LEBs), journal size 9404416 bytes (8 MiB, 38 LEBs)
[    4.105865] UBIFS (ubi3:0): reserved for root: 0 bytes (0 KiB)
[    4.105877] UBIFS (ubi3:0): media format: w4/r0 (latest is w4/r0), UUID DE44B251-9ED6-449D-BD52-D3FFF569DF69, small LPT model
[    4.120131] UBIFS (ubi3:2): background thread "ubifs_bgt3_2" started, PID 288
[    4.172597] UBIFS (ubi3:2): recovery needed
[    4.278600] UBIFS (ubi3:2): recovery completed
[    4.278674] UBIFS (ubi3:2): UBIFS: mounted UBI device 3, volume 2, name "cachefs"
[    4.278685] UBIFS (ubi3:2): LEB size: 253952 bytes (248 KiB), min./max. I/O unit sizes: 4096 bytes/4096 bytes
[    4.278696] UBIFS (ubi3:2): FS size: 65011712 bytes (62 MiB, 256 LEBs), journal size 9404416 bytes (8 MiB, 38 LEBs)
[    4.278704] UBIFS (ubi3:2): reserved for root: 0 bytes (0 KiB)
[    4.278716] UBIFS (ubi3:2): media format: w4/r0 (latest is w4/r0), UUID CFF0C008-8EC6-4DCB-8110-89CFCAF81483, small LPT model
[    4.290134] UBIFS (ubi3:1): background thread "ubifs_bgt3_1" started, PID 291
[    4.345319] UBIFS (ubi3:1): recovery needed
[    4.471166] UBIFS (ubi3:1): recovery completed
[    4.471224] UBIFS (ubi3:1): UBIFS: mounted UBI device 3, volume 1, name "logfs"
[    4.471234] UBIFS (ubi3:1): LEB size: 253952 bytes (248 KiB), min./max. I/O unit sizes: 4096 bytes/4096 bytes
[    4.471245] UBIFS (ubi3:1): FS size: 23871488 bytes (22 MiB, 94 LEBs), journal size 5332992 bytes (5 MiB, 21 LEBs)
[    4.471253] UBIFS (ubi3:1): reserved for root: 0 bytes (0 KiB)
[    4.471265] UBIFS (ubi3:1): media format: w4/r0 (latest is w4/r0), UUID FB5DF987-65B0-4BF4-B219-31B7A727C267, small LPT model
[    5.396957] subsys-restart: __subsystem_get(): Changing subsys fw_name to modem
[    5.398746] pil-q6v5-mss 4080000.qcom,mss: modem: loading from 0x88000000 to 0x8eb00000
[    5.469910] pil-q6v5-mss 4080000.qcom,mss: Debug policy not present - msadp. Continue.
[    5.486216] pil-q6v5-mss 4080000.qcom,mss: Loading MBA and DP (if present) from 0x8f100000 to 0x8f200000 size 100000
[    5.549147] pil-q6v5-mss 4080000.qcom,mss: MBA boot done
[    5.770256] QCMAP:start
[    5.812334] QTI:start
[    6.358162] USB QCMAP NL IOCTL Snd GETNEIGH Succ
[    6.384330] ------------[ cut here ]------------
[    6.384360] WARNING: CPU: 0 PID: 648 at /home/scl/ci/workspace/Soft4_P82M_H3GSEMF286D_uSDK/uSDK_svn/uSDK/platform_sdk/qualcomm/mdm9xxx.le/code/apps_proc/oe-core/build/tmp-glibc/work-shared/mdm9650/kernel-source/net/netfilter/nf_queue.c:35 nf_register_queue_handler+0x28/0x38()
[    6.384368] Modules linked in:
[    6.384379] CPU: 0 PID: 648 Comm: sh Not tainted 3.18.31 #1
[    6.384402] [<c001483c>] (unwind_backtrace) from [<c0011dd0>] (show_stack+0x10/0x14)
[    6.384418] [<c0011dd0>] (show_stack) from [<c001dff4>] (warn_slowpath_common+0x68/0x88)
[    6.384432] [<c001dff4>] (warn_slowpath_common) from [<c001e0a4>] (warn_slowpath_null+0x18/0x20)
[    6.384445] [<c001e0a4>] (warn_slowpath_null) from [<c0797130>] (nf_register_queue_handler+0x28/0x38)
[    6.384460] [<c0797130>] (nf_register_queue_handler) from [<c07b48e0>] (proc_sip_segment+0x58/0x9c)
[    6.384475] [<c07b48e0>] (proc_sip_segment) from [<c013b8fc>] (proc_sys_call_handler+0x98/0xb4)
[    6.384490] [<c013b8fc>] (proc_sys_call_handler) from [<c013b928>] (proc_sys_write+0x10/0x18)
[    6.384504] [<c013b928>] (proc_sys_write) from [<c00e852c>] (vfs_write+0xb8/0x170)
[    6.384518] [<c00e852c>] (vfs_write) from [<c00e899c>] (SyS_write+0x40/0x80)
[    6.384532] [<c00e899c>] (SyS_write) from [<c000e640>] (ret_fast_syscall+0x0/0x38)
[    6.384541] ---[ end trace 6524520c59c6de85 ]---
[    6.784088] random: dnsmasq urandom read with 94 bits of entropy available
[    6.791406] QCMAP:Init Complete
[    7.550801] Load cfg new driver..v2.0..
[    7.550824] cfg init, /home/scl/ci/workspace/Soft4_P82M_H3GSEMF286D_uSDK/uSDK_svn/uSDK/platform_sdk/qualcomm/mdm9xxx.le/code/apps_proc/oe-core/build/tmp-glibc/work-shared/mdm9650/kernel-source/drivers/cfg/cfg_param.c 574
[    7.575477]
[    7.575493] WPS_SSID=simcard_ro
[    7.575512] 5750535f535349443d0073696d636172645f726f
[    7.577647]
[    7.577647]  cfg init end, /home/scl/ci/workspace/Soft4_P82M_H3GSEMF286D_uSDK/uSDK_svn/uSDK/platform_sdk/qualcomm/mdm9xxx.le/code/apps_proc/oe-core/build/tmp-glibc/work-shared/mdm9650/kernel-source/drivers/cfg/cfg_param.c 633
[    7.577684] cfg init, /home/scl/ci/workspace/Soft4_P82M_H3GSEMF286D_uSDK/uSDK_svn/uSDK/platform_sdk/qualcomm/mdm9xxx.le/code/apps_proc/oe-core/build/tmp-glibc/work-shared/mdm9650/kernel-source/drivers/cfg/cfg_param.c 574
[    7.579343]
[    7.579355]
[    7.579373] 0000000000000000000000000000000000000000
[    7.579397]
[    7.579397]  cfg init end, /home/scl/ci/workspace/Soft4_P82M_H3GSEMF286D_uSDK/uSDK_svn/uSDK/platform_sdk/qualcomm/mdm9xxx.le/code/apps_proc/oe-core/build/tmp-glibc/work-shared/mdm9650/kernel-source/drivers/cfg/cfg_param.c 633
[    7.717731] cfg save index:0
[    7.933305] cfg save index:0
[   11.934754] pil-q6v5-mss 4080000.qcom,mss: modem: Brought out of reset
[   12.036296] zte_port_init: zte_port_init: zte port init
[   12.036314] zte_get_modem_state_usb_enmuation: zte_get_modem_state_usb_enmuation: ZTE zte_modem_state is 1=======
[   12.036398] apr_tal_link_state_cb: edge[mpss] link state[0]
[   12.040505] pil-q6v5-mss 4080000.qcom,mss: Subsystem error monitoring/handling services are up
[   12.040567] pil-q6v5-mss 4080000.qcom,mss: modem: Power/Clock ready interrupt received
[   12.040895] M-Notify: General: 7
[   12.044050] of_get_named_gpiod_flags: parsed 'wlan-en-gpio' property of node '/soc/qcom,cnss[0]' - status (0)
[   12.044216] cnss_pinctrl_init: Can not get active pin state!
[   12.060186] cnss_probe: Failed to enable PCIe RC0!
[   12.086494] of_get_named_gpiod_flags: parsed 'wlan-en-gpio' property of node '/soc/qcom,cnss[0]' - status (0)
[   12.086638] cnss_pinctrl_init: Can not get active pin state!
[   12.100168] cnss_probe: Failed to enable PCIe RC0!
[   12.189660] diag: In diag_send_feature_mask_update, control channel is not open, p: 0, c0f248f8
[   12.207413] Sending QMI_IPA_INIT_MODEM_DRIVER_REQ_V01
[   12.211391] ipa-wan ipa3_handle_indication_req:151 not send indication
[   12.219081] QMI_IPA_INIT_MODEM_DRIVER_REQ_V01 response received
[   12.219417] ipa ipa3_uc_state_check:307 uC is not loaded
[   12.255473] ipa ipa3_uc_wdi_event_log_info_handler:362 wdi stats sz invalid exp=160 is=164
[   12.255497] ipa ipa3_uc_ntn_event_log_info_handler:48 NTN stats sz invalid exp=156 is=112
[   12.369548] QTI_PPP:start
[   12.418114] Cleanup: Detected /dev/mtdblock13 for recoveryfs
[   12.430266] zte_usb_switch: zte_usb_switch:
[   12.430266] ==============================enter==========================
[   12.430282] zte_usb_switch: zte_usb_switch:
[   12.430282]  enter is_smem_read_complete=======
[   12.430292] zte_usb_check_read_q6_config_sucess is_smem_read_complete is 0
[   12.430301] zte_read_usb_config_args_from_q6:  sizeof(ZTE_config_args_s_type) = 628
[   12.430323]  GET USB CONFIG FILE FROM Q6 SIDE
[   12.430333]  zte wifi_adb_enable = 0
[   12.430339]  ZTE_usb_cpe_b6_file_exit = 0
[   12.430346]  is_disable_rndis = 0
[   12.430352] is_disable_automatic_install = 0
[   12.430362] zte_usb_set_net_mac_addr ZTE_USB_GET_INTERNAL_NET_MAC_ADDRESS: 34:4B:50:B7:EF:08
[   12.430372] zte_usb_set_net_mac_addr ZTE_USB_GET_INTERNAL_NET_MAC_ADDRESS: 34:4B:50:B7:EF:CF
[   12.430379] zte_usb_autorun_download_switch ZTE download: =DOWNLOAD
[   12.430385] zte_usb_autorun_download_switch ZTE autorun close: =CLOSE
[   12.430392] zte_usb_autorun_download_switch ZTE tcard_enable_state=1
[   12.430400] config_file_enable = 1
[   12.430400] download_value= 0
[   12.430400]  autorun_value = 0
[   12.430400]  composite_id = 0
[   12.430413] zte_usb_autorun_init ZTE_usb_switch_devices.VID = 19d2
[   12.430413]  ZTE_usb_switch_devices.PID = 16:
[   12.430421] zte_usb_switch releaseid = 5287
[   12.430429] zte_usb_switch serial_string = :
[   12.430437] zte_enable_usb: zte_enable_usb ============================enter=============== enable = 0
[   12.430445] zte_enable_usb: android_usb: already disabled
[   12.430452] zte_enable_usb: zte_enable_usb
[   12.430452] ============================exit=============== enable = 0
[   12.430461] zte_set_curent_device: zte_set_curent_device:
[   12.430461] ========================enter================================
[   12.430471] zte_set_curent_device: zte_set_curent_device: zte_usb_devices_used.FlagTcard as default state==================

Przy tej komendzie się jakby zawiesza w sensie nawet po odczekaniu minuty nic nie pluje:

root@mdm9650:~# cat /proc/kmsg

Stich86 you are using teamviver? I have one machine on windows, I can put this program there and you will work. The modem is connected to the USB converter. It will install all the drivers and let's go ...

Give me 30-40 minutes and I'll put you on teamviver. I will send the login and password to PM via this forum

Okay, I sent you this data. Just remember that do not write anything to me by e-mail, unless it is some confidential information. I rarely check my e-mail and I visit the forum quite often.

I send by PW on this forum but if you didn't get it give me your mail

PW it mean when you clic on me for any post then there is option send email by this forum . Do you see?

Okay, throw in and let's go. If you don't want to by TM, I can do it too. But you would be faster yourself

Write when you do it

I did it but I can one more time no problem