Odp: Huawei B970b alt oprogramowanie
Wydanie BB zbudowane z imagebuildera.
Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.
Strony Poprzednia 1 2 3 4 5 Następna
Zaloguj się lub zarejestruj by napisać odpowiedź
Nie jesteś zalogowany. Proszę się zalogować lub zarejestrować.
eko.one.pl → Oprogramowanie / Software → Huawei B970b alt oprogramowanie
Strony Poprzednia 1 2 3 4 5 Następna
Zaloguj się lub zarejestruj by napisać odpowiedź
Wydanie BB zbudowane z imagebuildera.
Spróbować zbudować ?
Tak, spróbuj.
Próbuję skompilować BB z tych źródeł
https://github.com/openwrt-vgv7519/open … er-breaker
Niestety po wybraniu Target System->Broadcom BCM47xx/53xx (MIPS)
nie ma w Target Profile Huawei E970.
Gdzie to może być.
Patch w target/linux/brcm47xx jest.
Całe bradocom b43 skompiluj.
Mam wybrane
Target System : Broadcom BCM47xx/53xx (MIPS)
Subtarget : Generic
Target Profile : Broadcom SoC, Ethernet, BCM43xx Wifi B43
Skompilowałem a i tak później w konfiguratorze nie mogę w Target Profile znaleźć Huawei'a.
Więc nie wybieraj nic, skompiluj wszystko i powinno być.
W folderze bin nie mam pliku dla E970 więc spróbowałem wgrać ten
openwrt-brcm47xx-generic-squashfs.trx
ale niestety nie idzie.
W konfiguratorze (make menuconfig) nie widać tego routera pomimo że zaciągnąłem źródła w wersji Barrier Breaker (14.07).
root@(none):/tmp# sysupgrade -n firmware.bin
Invalid image type. Please use only .trx files
Image check 'platform_check_image' failed.
root@(none):/tmp#
Szukam tego pakietu
valgrind-3.8.1.tar.bz2
który potrzebuję do builda dla BB.
Wrzucone w google od razu to pokazuje, np. https://src.fedoraproject.org/lookaside … 83f1d6e38/
Aż w ciekawości odpaliłem sobie imagebuildera. Domyślnie robi obrazy, ten dla dla e970 ma 3.8MB, po wywaleniu odhcp* i ppp-mod-pppoe ma 3.6M. Pewnie należało by tam jeszcze dodać coś od usb/option itd.
Ja jestem teraz na etapie kompilacji ale aż tak szybkiej maszyny nie mam. Coś builderowi pomieszało się z ipv6 jak wywaliłem to i tak dalej ma problem z kompilacją iptables.
Zrobiłem make clean i czekam.
Tutaj w poscie 8
https://forum.archive.openwrt.org/viewt … p?id=47953
piszą co trzeba sprawdzić żeby usunąć ipv6.
Po skompilowaniu utworzył mi się tylko plik openwrt-e970-squashfs-gz.bin dla E970. Tego pliku nie łapie sysupgrade więc usunąłem pierwsze 100 bajtów żeby plik zaczynał się od HDR0.
Niestety po sysupgrade router dalej się uruchamia z openwrt AA a nie BB.
Przy takim boot logu.
root@(none):/# Decompressing...........done
CFE version 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: Mon Feb 27 11:17:46 CST 2012 (bcm@bcm-1)
Copyright (C) 2000-2008 Broadcom Corporation.
Init Arena
Init Devs.
Boot partition size = 262144(0x40000)
et0: Broadcom BCM47xx 10/100 Mbps Ethernet Controller
CFE reboot no init flag0 = 0x622f2123,flag1 = 0x732f6e69,flag2 = 0x705f7467,number = 0x730e0a68
CFE reboot flag0 = 0x12345678, flag1 = 0x0,flag2 = 0xffffffff,reboot_number = 0x1
CPU type 0x29029: 240MHz
Tot mem: 32768 KBytes
CFE mem: 0x80400000 - 0x804A0910 (657680)
Data: 0x80434670 - 0x80439130 (19136)
BSS: 0x80439130 - 0x8043A910 (6112)
Heap: 0x8043A910 - 0x8049E910 (409600)
Stack: 0x8049E910 - 0x804A0910 (8192)
Text: 0x80400000 - 0x80434668 (214632)
Compare factory.
Device eth0: hwaddr 1C-1D-67-8E-50-B2, ipaddr 192.168.1.1, mask 255.255.255.0
gateway not set, nameserver not set
Loader:raw Filesys:raw Dev:flash0.os File: Options:(null)
Loading: ......... 2980108 bytes read
Entry at 0x80001000
Closing network.
Starting program at 0x80001000
[ 0.000000] Linux version 3.3.8 (user@ubuntu) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Thu May 26 22:51:03 CEST 2022
[ 0.000000] CPU revision is: 00029029 (Broadcom BMIPS3300)
[ 0.000000] bcm47xx: using ssb bus
[ 0.000000] ssb: Found chip with id 0x5354, rev 0x03 and package 0x00
[ 0.000000] ssb: chipcommon status is 0x0
[ 0.000000] ssb: Initializing MIPS core...
[ 0.000000] ssb: set_irq: core 0x0806, irq 4 => 4
[ 0.000000] ssb: set_irq: core 0x0816, irq 5 => 2
[ 0.000000] ssb: set_irq: core 0x0812, irq 2 => 5
[ 0.000000] ssb: after irq reconfiguration
[ 0.000000] ssb: core 0x0800, irq : 2(S) 3* 4 5 6 D I
[ 0.000000] ssb: core 0x0806, irq : 2(S) 3 4* 5 6 D I
[ 0.000000] ssb: core 0x0816, irq : 2(S)* 3 4 5 6 D I
[ 0.000000] ssb: core 0x0819, irq : 2(S) 3 4 5 6* D I
[ 0.000000] ssb: core 0x080f, irq : 2(S) 3 4 5 6 D I*
[ 0.000000] ssb: core 0x0812, irq : 2(S) 3 4 5* 6 D I
[ 0.000000] ssb: core 0x081c, irq : 2(S) 3 4 5 6 D I*
[ 0.000000] found parallel flash.
[ 0.000000] can not parse nvram name (null)rxpo2g(null) with value 0xfff8 got -34
[ 0.000000] ssb: Sonics Silicon Backplane found at address 0x18000000
[ 0.000000] gpiochip_add: registered GPIOs 0 to 15 on device: bcm47xx
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00002000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] Early memory PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00002000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
[ 0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Primary instruction cache 16kB, VIPT, 4-way, linesize 16 bytes.
[ 0.000000] Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[ 0.000000] Memory: 29280k/32768k available (2381k kernel code, 3488k reserved, 364k data, 164k init, 0k highmem)
[ 0.000000] NR_IRQS:128
[ 0.000000] bcm47xx: detected Huawei E970, starting gpio watchdog pet timer
[ 0.000000] console [ttyS0] enabled
[ 0.004000] Calibrating delay loop... 239.10 BogoMIPS (lpj=478208)
[ 0.040000] pid_max: default: 32768 minimum: 301
[ 0.044000] Mount-cache hash table entries: 512
[ 0.052000] NET: Registered protocol family 16
[ 0.088000] bio: create slab <bio-0> at 0
[ 0.100000] Switching to clocksource MIPS
[ 0.128000] NET: Registered protocol family 2
[ 0.132000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.140000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[ 0.148000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.156000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.160000] TCP reno registered
[ 0.164000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.172000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.180000] NET: Registered protocol family 1
[ 0.192000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.200000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.212000] msgmni has been set to 57
[ 0.216000] io scheduler noop registered
[ 0.220000] io scheduler deadline registered (default)
[ 0.224000] Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
[ 0.252000] serial8250: ttyS0 at MMIO 0xb8000300 (irq = 3) is a U6_16550A
[ 0.280000] serial8250: ttyS1 at MMIO 0xb8000400 (irq = 3) is a U6_16550A
[ 0.312000] serial8250.0: ttyS0 at MMIO 0xb8000300 (irq = 3) is a U6_16550A
[ 0.340000] serial8250.0: ttyS1 at MMIO 0xb8000400 (irq = 3) is a U6_16550A
[ 0.356000] bcm47xx_pflash: flash init: 0x1c000000 0x02000000
[ 0.364000] Physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x001a01
[ 0.376000] Amd/Fujitsu Extended Query Table at 0x0040
[ 0.380000] Amd/Fujitsu Extended Query version 1.3.
[ 0.384000] Physically mapped flash: Swapping erase regions for top-boot CFI table.
[ 0.392000] number of CFI chips: 1
[ 0.396000] bcm47xx_pflash: Flash device: 0x2000000 at 0x1fc00000
[ 0.404000] bcm47xx_part: bootloader size: 262144
[ 0.412000] bcm47xx_part: Looking for dual image
[ 0.416000] bcm47xx_part: TRX offset : 0
[ 0.420000] 5 bcm47xx partitions found on MTD device Physically mapped flash
[ 0.428000] Creating 5 MTD partitions on "Physically mapped flash":
[ 0.436000] 0x000000000000-0x000000040000 : "cfe"
[ 0.448000] 0x000000040000-0x0000003e0000 : "linux"
[ 0.456000] 0x00000017ec00-0x0000003e0000 : "rootfs"
[ 0.464000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.480000] mtd: partition "rootfs" set to be root filesystem
[ 0.488000] mtd: partition "rootfs_data" created automatically, ofs=2E0000, len=100000
[ 0.496000] 0x0000002e0000-0x0000003e0000 : "rootfs_data"
[ 0.508000] 0x0000003f0000-0x000000400000 : "nvram"
[ 0.520000] 0x0000003e0000-0x0000003f0000 : "board_data"
[ 0.532000] bcm47xx_sflash: error registering platform driver: -19
[ 0.540000] bcm47xx_nflash: error registering platform driver: -19
[ 0.548000] b44: Broadcom 44xx/47xx 10/100 PCI ethernet driver version 2.0
[ 0.560000] b44 ssb0:0: eth0: Broadcom 44xx/47xx 10/100 PCI ethernet driver 1c:1d:67:8e:50:b2
[ 0.572000] BCM47xx Watchdog Timer enabled (30 seconds, nowayout)
[ 0.580000] TCP cubic registered
[ 0.584000] NET: Registered protocol family 17
[ 0.588000] 8021q: 802.1Q VLAN Support v1.8
[ 0.604000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 0.612000] Freeing unused kernel memory: 164k freed
[ 4.040000] diag: Detected 'Huawei E970'
[ 4.104000] b44 ssb0:0: eth0: Link is up at 100 Mbps, full duplex
[ 4.108000] b44 ssb0:0: eth0: Flow control is off for TX and off for RX
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
[ 12.184000] JFFS2 notice: (286) jffs2_build_xattr_subsystem: complete building xattr subsystem, 16 of xdatum (0 unchecked, 15 orphan) and 32 of xref (0 dead, 30 orphan) found.
[ 13.696000] SCSI subsystem initialized
[ 13.976000] usbcore: registered new interface driver usbfs
[ 13.980000] usbcore: registered new interface driver hub
[ 13.992000] usbcore: registered new device driver usb
[ 14.528000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 14.536000] ehci-platform ehci-platform.0: Generic Platform EHCI Controller
[ 14.544000] ehci-platform ehci-platform.0: new USB bus registered, assigned bus number 1
[ 14.552000] ehci-platform ehci-platform.0: irq 6, io mem 0x18003800
[ 14.572000] ehci-platform ehci-platform.0: USB 2.0 started, EHCI 1.00
[ 14.580000] hub 1-0:1.0: USB hub found
[ 14.584000] hub 1-0:1.0: 2 ports detected
[ 14.624000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 14.628000] ohci-platform ohci-platform.0: Generic Platform OHCI Controller
[ 14.636000] ohci-platform ohci-platform.0: new USB bus registered, assigned bus number 2
[ 14.644000] ohci-platform ohci-platform.0: irq 6, io mem 0x18003000
[ 14.712000] hub 2-0:1.0: USB hub found
[ 14.716000] hub 2-0:1.0: 2 ports detected
[ 14.900000] usb 1-1: new high-speed USB device number 2 using ehci-platform
jffs2 not ready yet; using ramdisk
- init -
[ 35.756000] b44 ssb0:0: eth0: powering down PHY
Please press Enter to activate this console. [ 37.904000] Compat-drivers backport release: compat-drivers-2012-09-04-2-gddac993
[ 37.912000] Backport based on wireless-testing.git master-2012-09-07
[ 37.920000] compat.git: wireless-testing.git
[ 38.012000] cfg80211: Calling CRDA to update world regulatory domain
[ 38.016000] cfg80211: World regulatory domain updated:
[ 38.024000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 38.032000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 38.040000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 38.048000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 38.056000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 38.064000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 39.092000] b43-phy0: Broadcom 5354 WLAN found (core revision 13)
[ 39.120000] b43-phy0: Found PHY: Analog 6, Type 5 (LP), Revision 0
[ 39.148000] Broadcom 43xx driver loaded [ Features: PNL ]
[ 39.232000] Broadcom 43xx-legacy driver loaded [ Features: PLID ]
[ 40.032000] usbcore: registered new interface driver usbserial
[ 40.036000] USB Serial support registered for generic
[ 40.044000] usbcore: registered new interface driver usbserial_generic
[ 40.048000] usbserial: USB Serial Driver core
[ 40.288000] USB Serial support registered for GSM modem (1-port)
[ 40.292000] option 1-1:1.0: GSM modem (1-port) converter detected
[ 40.300000] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0
[ 40.308000] option 1-1:1.1: GSM modem (1-port) converter detected
[ 40.316000] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1
[ 40.324000] option 1-1:1.2: GSM modem (1-port) converter detected
[ 40.332000] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB2
[ 40.340000] usbcore: registered new interface driver option
[ 40.344000] option: v0.7.2:USB Driver for GSM modems
[ 46.376000] b44 ssb0:0: eth0: Link is up at 100 Mbps, full duplex
[ 46.384000] b44 ssb0:0: eth0: Flow control is off for TX and off for RX
[ 46.400000] device eth0.0 entered promiscuous mode
[ 46.408000] device eth0 entered promiscuous mode
[ 46.416000] br-lan: port 1(eth0.0) entered forwarding state
[ 46.424000] br-lan: port 1(eth0.0) entered forwarding state
[ 48.428000] br-lan: port 1(eth0.0) entered forwarding state
BusyBox v1.19.4 (2022-05-26 22:03:58 CEST) built-in shell (ash)
Enter 'help' for a list of built-in commands.
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
ATTITUDE ADJUSTMENT (Attitude Adjustment, r35331)
-----------------------------------------------------
* 1/4 oz Vodka Pour all ingredients into mixing
* 1/4 oz Gin tin with ice, strain into glass.
* 1/4 oz Amaretto
* 1/4 oz Triple sec
* 1/4 oz Peach schnapps
* 1/4 oz Sour mix
* 1 splash Cranberry juice
-----------------------------------------------------
root@OpenWrt:/#Po paru pingach do routera mniej więcej w tym momencie
[ 0.612000] Freeing unused kernel memory: 164k freed
[ 4.040000] diag: Detected 'Huawei E970'
[ 4.104000] b44 ssb0:0: eth0: Link is up at 100 Mbps, full duplex
[ 4.108000] b44 ssb0:0: eth0: Flow control is off for TX and off for RX
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
[ 12.184000] JFFS2 notice: (286) jffs2_build_xattr_subsystem: complete building xattr subsystem, 16 of xdatum (0 unchecked, 15 orphan) and 32 of xref (0 dead, 30 orphan) found.
[ 13.696000] SCSI subsystem initialized
[ 13.976000] usbcore: registered new interface driver usbfs
[ 13.980000] usbcore: registered new interface driver hub
[ 13.992000] usbcore: registered new device driver usb
router przestaje odpowiadać na pingi
Zawsze był tylko jeden plik. Więc nic nie wycinaj tylko jego wgraj.
Jak próbuję wgrać ten openwrt-e970-squashfs-gz.bin
podając sysupgrade -n /tmp/openwrt-e970-squashfs-gz.bin
to wyskakuje błąd
root@(none):/tmp# sysupgrade -n openwrt-e970-squashfs.gz.bin
Invalid image type. Please use only .trx files
Image check 'platform_check_image' failed.
root@(none):/tmp#
Spróbowałem jeszcze raz wgrać nową wersję BB.
Wynik z próby
root@(none):/tmp# wget http://192.168.1.99/firmware.trx
root@(none):/tmp# ls
firmware.trx
root@(none):/tmp# sysupgrade -n firmware.trx
Sending TERM to remaining processes ... hotplug2 lock
Sending KILL to remaining processes ...
Switching to ramdisk...
Performing system upgrade...
Upgrade completed
Rebooting system...
[ 1076.552000] Restarting system.
[ 1076.556000] Please stand by while rebooting the system...
Decompressing...........done
CFE version 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: Mon Feb 27 11:17:46 CST 2012 (bcm@bcm-1)
Copyright (C) 2000-2008 Broadcom Corporation.
Init Arena
Init Devs.
Boot partition size = 262144(0x40000)
et0: Broadcom BCM47xx 10/100 Mbps Ethernet Controller
CFE reboot no init flag0 = 0x622f2123,flag1 = 0x732f6e69,flag2 = 0x705f7465,number = 0x730a0a68
CFE reboot flag0 = 0x12345678, flag1 = 0x0,flag2 = 0xffffffff,reboot_number = 0x1
CPU type 0x29029: 240MHz
Tot mem: 32768 KBytes
CFE mem: 0x80400000 - 0x804A0910 (657680)
Data: 0x80434670 - 0x80439130 (19136)
BSS: 0x80439130 - 0x8043A910 (6112)
Heap: 0x8043A910 - 0x8049E910 (409600)
Stack: 0x8049E910 - 0x804A0910 (8192)
Text: 0x80400000 - 0x80434668 (214632)
Compare factory.
Device eth0: hwaddr 1C-1D-67-8E-50-B2, ipaddr 192.168.1.1, mask 255.255.255.0
gateway not set, nameserver not set
Loader:raw Filesys:raw Dev:flash0.os File: Options:(null)
Loading: ......... 2980108 bytes read
Entry at 0x80001000
Closing network.
Starting program at 0x80001000
[ 0.000000] Linux version 3.3.8 (user@ubuntu) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Thu May 26 22:51:03 CEST 2022
[ 0.000000] CPU revision is: 00029029 (Broadcom BMIPS3300)
[ 0.000000] bcm47xx: using ssb bus
[ 0.000000] ssb: Found chip with id 0x5354, rev 0x03 and package 0x00
[ 0.000000] ssb: chipcommon status is 0x0
[ 0.000000] ssb: Initializing MIPS core...
[ 0.000000] ssb: set_irq: core 0x0806, irq 4 => 4
[ 0.000000] ssb: set_irq: core 0x0816, irq 5 => 2
[ 0.000000] ssb: set_irq: core 0x0812, irq 2 => 5
[ 0.000000] ssb: after irq reconfiguration
[ 0.000000] ssb: core 0x0800, irq : 2(S) 3* 4 5 6 D I
[ 0.000000] ssb: core 0x0806, irq : 2(S) 3 4* 5 6 D I
[ 0.000000] ssb: core 0x0816, irq : 2(S)* 3 4 5 6 D I
[ 0.000000] ssb: core 0x0819, irq : 2(S) 3 4 5 6* D I
[ 0.000000] ssb: core 0x080f, irq : 2(S) 3 4 5 6 D I*
[ 0.000000] ssb: core 0x0812, irq : 2(S) 3 4 5* 6 D I
[ 0.000000] ssb: core 0x081c, irq : 2(S) 3 4 5 6 D I*
[ 0.000000] found parallel flash.
[ 0.000000] can not parse nvram name (null)rxpo2g(null) with value 0xfff8 got -34
[ 0.000000] ssb: Sonics Silicon Backplane found at address 0x18000000
[ 0.000000] gpiochip_add: registered GPIOs 0 to 15 on device: bcm47xx
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00002000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] Early memory PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00002000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
[ 0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Primary instruction cache 16kB, VIPT, 4-way, linesize 16 bytes.
[ 0.000000] Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[ 0.000000] Memory: 29280k/32768k available (2381k kernel code, 3488k reserved, 364k data, 164k init, 0k highmem)
[ 0.000000] NR_IRQS:128
[ 0.000000] bcm47xx: detected Huawei E970, starting gpio watchdog pet timer
[ 0.000000] console [ttyS0] enabled
[ 0.004000] Calibrating delay loop... 239.10 BogoMIPS (lpj=478208)
[ 0.040000] pid_max: default: 32768 minimum: 301
[ 0.044000] Mount-cache hash table entries: 512
[ 0.052000] NET: Registered protocol family 16
[ 0.088000] bio: create slab <bio-0> at 0
[ 0.100000] Switching to clocksource MIPS
[ 0.128000] NET: Registered protocol family 2
[ 0.132000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.140000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[ 0.148000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.156000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.160000] TCP reno registered
[ 0.164000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.172000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.180000] NET: Registered protocol family 1
[ 0.192000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.200000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.212000] msgmni has been set to 57
[ 0.216000] io scheduler noop registered
[ 0.220000] io scheduler deadline registered (default)
[ 0.224000] Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
[ 0.252000] serial8250: ttyS0 at MMIO 0xb8000300 (irq = 3) is a U6_16550A
[ 0.280000] serial8250: ttyS1 at MMIO 0xb8000400 (irq = 3) is a U6_16550A
[ 0.312000] serial8250.0: ttyS0 at MMIO 0xb8000300 (irq = 3) is a U6_16550A
[ 0.340000] serial8250.0: ttyS1 at MMIO 0xb8000400 (irq = 3) is a U6_16550A
[ 0.356000] bcm47xx_pflash: flash init: 0x1c000000 0x02000000
[ 0.364000] Physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x001a01
[ 0.376000] Amd/Fujitsu Extended Query Table at 0x0040
[ 0.380000] Amd/Fujitsu Extended Query version 1.3.
[ 0.384000] Physically mapped flash: Swapping erase regions for top-boot CFI table.
[ 0.392000] number of CFI chips: 1
[ 0.396000] bcm47xx_pflash: Flash device: 0x2000000 at 0x1fc00000
[ 0.404000] bcm47xx_part: bootloader size: 262144
[ 0.412000] bcm47xx_part: Looking for dual image
[ 0.416000] bcm47xx_part: TRX offset : 0
[ 0.420000] 5 bcm47xx partitions found on MTD device Physically mapped flash
[ 0.428000] Creating 5 MTD partitions on "Physically mapped flash":
[ 0.436000] 0x000000000000-0x000000040000 : "cfe"
[ 0.448000] 0x000000040000-0x0000003e0000 : "linux"
[ 0.456000] 0x00000017ec00-0x0000003e0000 : "rootfs"
[ 0.464000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.480000] mtd: partition "rootfs" set to be root filesystem
[ 0.488000] mtd: partition "rootfs_data" created automatically, ofs=2E0000, len=100000
[ 0.496000] 0x0000002e0000-0x0000003e0000 : "rootfs_data"
[ 0.508000] 0x0000003f0000-0x000000400000 : "nvram"
[ 0.520000] 0x0000003e0000-0x0000003f0000 : "board_data"
[ 0.532000] bcm47xx_sflash: error registering platform driver: -19
[ 0.540000] bcm47xx_nflash: error registering platform driver: -19
[ 0.548000] b44: Broadcom 44xx/47xx 10/100 PCI ethernet driver version 2.0
[ 0.560000] b44 ssb0:0: eth0: Broadcom 44xx/47xx 10/100 PCI ethernet driver 1c:1d:67:8e:50:b2
[ 0.572000] BCM47xx Watchdog Timer enabled (30 seconds, nowayout)
[ 0.580000] TCP cubic registered
[ 0.584000] NET: Registered protocol family 17
[ 0.588000] 8021q: 802.1Q VLAN Support v1.8
[ 0.604000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 0.612000] Freeing unused kernel memory: 164k freed
[ 4.028000] diag: Detected 'Huawei E970'
[ 4.092000] b44 ssb0:0: eth0: Link is up at 100 Mbps, full duplex
[ 4.096000] b44 ssb0:0: eth0: Flow control is off for TX and off for RX
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
[ 12.180000] JFFS2 notice: (286) jffs2_build_xattr_subsystem: complete building xattr subsystem, 17 of xdatum (0 unchecked, 16 orphan) and 34 of xref (0 dead, 32 orphan) found.
[ 13.688000] SCSI subsystem initialized
[ 13.968000] usbcore: registered new interface driver usbfs
[ 13.972000] usbcore: registered new interface driver hub
[ 13.980000] usbcore: registered new device driver usb
[ 14.520000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 14.524000] ehci-platform ehci-platform.0: Generic Platform EHCI Controller
[ 14.532000] ehci-platform ehci-platform.0: new USB bus registered, assigned bus number 1
[ 14.544000] ehci-platform ehci-platform.0: irq 6, io mem 0x18003800
[ 14.560000] ehci-platform ehci-platform.0: USB 2.0 started, EHCI 1.00
[ 14.568000] hub 1-0:1.0: USB hub found
[ 14.572000] hub 1-0:1.0: 2 ports detected
[ 14.612000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 14.616000] ohci-platform ohci-platform.0: Generic Platform OHCI Controller
[ 14.624000] ohci-platform ohci-platform.0: new USB bus registered, assigned bus number 2
[ 14.632000] ohci-platform ohci-platform.0: irq 6, io mem 0x18003000
[ 14.700000] hub 2-0:1.0: USB hub found
[ 14.704000] hub 2-0:1.0: 2 ports detected
[ 14.888000] usb 1-1: new high-speed USB device number 2 using ehci-platform
jffs2 not ready yet; using ramdisk
- init -
[ 35.744000] b44 ssb0:0: eth0: powering down PHY
Please press Enter to activate this console. [ 37.892000] Compat-drivers backport release: compat-drivers-2012-09-04-2-gddac993
[ 37.900000] Backport based on wireless-testing.git master-2012-09-07
[ 37.904000] compat.git: wireless-testing.git
[ 37.980000] cfg80211: Calling CRDA to update world regulatory domain
[ 37.984000] cfg80211: World regulatory domain updated:
[ 37.992000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 38.000000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 38.008000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 38.016000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 38.024000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 38.032000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 39.072000] b43-phy0: Broadcom 5354 WLAN found (core revision 13)
[ 39.104000] b43-phy0: Found PHY: Analog 6, Type 5 (LP), Revision 0
[ 39.132000] Broadcom 43xx driver loaded [ Features: PNL ]
[ 39.216000] Broadcom 43xx-legacy driver loaded [ Features: PLID ]
[ 40.008000] usbcore: registered new interface driver usbserial
[ 40.016000] USB Serial support registered for generic
[ 40.020000] usbcore: registered new interface driver usbserial_generic
[ 40.028000] usbserial: USB Serial Driver core
[ 40.264000] USB Serial support registered for GSM modem (1-port)
[ 40.272000] option 1-1:1.0: GSM modem (1-port) converter detected
[ 40.280000] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0
[ 40.288000] option 1-1:1.1: GSM modem (1-port) converter detected
[ 40.296000] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1
[ 40.300000] option 1-1:1.2: GSM modem (1-port) converter detected
[ 40.308000] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB2
[ 40.316000] usbcore: registered new interface driver option
[ 40.324000] option: v0.7.2:USB Driver for GSM modems
[ 46.420000] b44 ssb0:0: eth0: Link is up at 100 Mbps, full duplex
[ 46.424000] b44 ssb0:0: eth0: Flow control is off for TX and off for RX
[ 46.444000] device eth0.0 entered promiscuous mode
[ 46.452000] device eth0 entered promiscuous mode
[ 46.460000] br-lan: port 1(eth0.0) entered forwarding state
[ 46.464000] br-lan: port 1(eth0.0) entered forwarding state
[ 48.468000] br-lan: port 1(eth0.0) entered forwarding state
BusyBox v1.19.4 (2022-05-26 22:03:58 CEST) built-in shell (ash)
Enter 'help' for a list of built-in commands.
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
ATTITUDE ADJUSTMENT (Attitude Adjustment, r35331)
-----------------------------------------------------
* 1/4 oz Vodka Pour all ingredients into mixing
* 1/4 oz Gin tin with ice, strain into glass.
* 1/4 oz Amaretto
* 1/4 oz Triple sec
* 1/4 oz Peach schnapps
* 1/4 oz Sour mix
* 1 splash Cranberry juice
-----------------------------------------------------
root@OpenWrt:/#To wgraj jawnie przez mtd i zobacz czy uda sie zapisać.
Mam takie partycje
root@(none):/proc# cat mtd
dev: size erasesize name
mtd0: 00040000 00010000 "cfe"
mtd1: 003a0000 00010000 "linux"
mtd2: 00261400 00010000 "rootfs"
mtd3: 00100000 00010000 "rootfs_data"
mtd4: 00010000 00002000 "nvram"
mtd5: 00010000 00010000 "board_data"
root@(none):/proc#
Według tego opisu
https://openwrt.org/docs/techref/mtd
mtd -r write /tmp/firmware.trx linux
?
Tak, możesz spróbować.
Jak jestem w trybie failsafe bo tylko w tym trybie mam dostęp po ethernecie do routera to po wpisaniu komendy
mtd -r write /tmp/firmware.trx linux
niestety nic się nie dzieje.
Polecenie wpisuję z poziomu terminala po rs232.
Jak mogę odebrać na routerze dane po rs232 ?
Dostęp po kablu ethernetowym wykłada się jednak wtedy
[ 35.748000] b44 ssb0:0: eth0: powering down PHY
Wydaje mi się że jest jakiś problem z pamięcią flash bo nawet jak przy normalnym uruchomieniu zrobię zmiany w /etc/config/network to niestety router ich nie pamięta.
"rs232" to konsola systemowa i wszystko leci na terminal. Jeżeli nic nie ma to nie ma, po prostu nic wyświetla. Zmień to "linux" na konkretny numer partycji i zobacz. Możesz dać też -e żeby wstępnie skasować pamięć.
Próbowałem zamiast linux wpisać mtd1 ale bez zmian
Wydaje mi się że nie mam dostępu po ethernecie z powodu watchdoga
Jest on aktywowany tutaj w ok 5 sekundzie
[ 0.532000] bcm47xx_sflash: error registering platform driver: -19
[ 0.540000] bcm47xx_nflash: error registering platform driver: -19
[ 0.548000] b44: Broadcom 44xx/47xx 10/100 PCI ethernet driver version 2.0
[ 0.560000] b44 ssb0:0: eth0: Broadcom 44xx/47xx 10/100 PCI ethernet driver 1c:1d:67:8e:50:b2
[ 0.572000] BCM47xx Watchdog Timer enabled (30 seconds, nowayout)
A po 30 sekundach
- init -
[ 35.740000] b44 ssb0:0: eth0: powering down PHY
Please press Enter to activate this console. [ 37.888000] Compat-drivers backport release: compat-drivers-2012-09-04-2-gddac993
[ 37.896000] Backport based on wireless-testing.git master-2012-09-07
[ 37.900000] compat.git: wireless-testing.git
[ 37.972000] cfg80211: Calling CRDA to update world regulatory domain
[ 37.976000] cfg80211: World regulatory domain updated:
[ 37.984000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 37.992000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 38.000000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 38.008000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 38.016000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 38.024000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 39.068000] b43-phy0: Broadcom 5354 WLAN found (core revision 13)
[ 39.096000] b43-phy0: Found PHY: Analog 6, Type 5 (LP), Revision 0
[ 39.124000] Broadcom 43xx driver loaded [ Features: PNL ]
[ 39.208000] Broadcom 43xx-legacy driver loaded [ Features: PLID ]
i już wtedy nie mam dostępu do routera pod ip 192.168.1.1
root@OpenWrt:/# nvram show | grep watch*
is_need_watch=enable
watchdog=3000
root@OpenWrt:/#
Nie wiem czy te ustawienia z nvram są wogóle brane przez openwrt. Pochodzą z oryginalnego firmware'u.
Wydaje mi się że nie mogę wgrać czegoś innego z tego powodu
mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
Nie mam możliwości wgrania po tftp. Mtd też nie działa. Sysupgrade też nie. Tzn niby coś robi, firmware wgra ale jak zrestartuję router to zmian nie widać.
Strony Poprzednia 1 2 3 4 5 Następna
Zaloguj się lub zarejestruj by napisać odpowiedź
eko.one.pl → Oprogramowanie / Software → Huawei B970b alt oprogramowanie
Forum oparte o PunBB, wspierane przez Informer Technologies, Inc