Nie jesteś zalogowany. Proszę się zalogować lub zarejestrować.
eko.one.pl → Sprzęt / Hardware → ZTE MF286A - Openwrt
Strony Poprzednia 1 … 12 13 14 15 16 … 21 Następna
Zaloguj się lub zarejestruj by napisać odpowiedź
Ok, w sumie to 100 zł to nie majątek do zabawy 
To poszukam wątek o R, i pokaże z konsoli
Wszystko wkleić ?
Musze zlogować do jakiegoś pliku chyba, tylko jak, które dane potrzebne ?
zrob backup partycji na usb jak w "A"
ilosc partycji pewnie bedzie inna to odpowiednio zrob modyfikację pętli.
oraz zapisz wszystko co wypluwa UART podczas startu
Sproboj tez zatrzymac uboot i printenv
Jak tam PR?
Zapodajcie linka do niego
Jeszcze nie ma.
PR do obu poszedł: https://github.com/openwrt/openwrt/pull/9274
Fajnie, ładny zestaw się nam zrobił.
Fajnie, ładny zestaw się nam zrobił.
Zgodnie z tym: https://eko.one.pl/forum/viewtopic.php? … 43#p257543
Został nam jeden z piątki ZTE MF286: ZTE MF286C. 
Tylko chyba nie występuje w PL...
Może być, że tylko hameryczka, jakiekolwiek info o nim znalazłem tylko na fccid.io.
Raczej niedostępny w Europie (np. Claro w Ameryce Południowej, MTN w Ghanie).
Dobra dobra. Jak życie pokazuje zaraz ktoś wyskoczy z tekstem że ma inny zte
Lepiej tak , niż na siłę próbowałby wgrywać coś , co jest nie do tego modelu..
sprawdzajcie IMEI routerow u dedykowanych operatorów. Lekko 50% routerow zwłaszcza z OLX ma na sobie raty np. w T-mobile
Wraz z dzisiejszą kompilacją, obrazy dla MF286A zostały przeniesione do normalnego katalogu z buildami (użyj wyszukiwarki).
Hmmm
Czy ja coś źle zrobiłem upgrade routera ?
Zrobiłem:
sysupgrade -n /tmp/luci-21.02-snapshot-r16500-zte_mf286a-squa
shfs-sysupgrade.bin
I teraz chyba się w kółko restartuje... 
Podłącz konsolę i zobacz dlaczego.
hmmm
1352] (driver?)
[ 4.018115] 1f05 102400 mtdblock5
[ 4.018117] (driver?)
[ 4.024873] 1f06 640 mtdblock6
[ 4.024875] (driver?)
[ 4.031636] 1f07 128 mtdblock7
[ 4.031638] (driver?)
[ 4.038400] 1f08 1280 mtdblock8
[ 4.038402] (driver?)
[ 4.045158] 1f09 125312 mtdblock9
[ 4.045160] (driver?)
[ 4.051919] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[ 4.060454] Rebooting in 1 seconds..Nie robił ci się ubifs, wgraj obraz jeszcze raz przez inittramfs. Jak to zrobisz i uruchomi się normalnie z flash to zrób jeszcze raz sysupgrade i zobacz co będzie.
zrobiłem w międzyczasie przez inittramfs i tak samo mam kernel panic.
Czyli jakby błąd w obrazie w tych ostatnich ??
Zrobiłem update starszą wersją i obraz ruszył w inittramfs
Żaden z nowych nie działa
Nie wiem. Pokaz komplet, od uruchomienia initramfs, to co wyświetla podczas wgrywania i sam start systemie. Nie edytuj nic, nie wycinaj nic.
zrobie wiec do pliku logi, zaraz postaram sie wrzucic
po wgraniu najnowszej wersji:
U-Boot 1.1.4 (Sep 27 2017 - 19:55:03)
ap152 - Dragonfly 1.0DRAM:
sri
ath_ddr_initial_config(278): (ddr2 init)
ath_sys_frequency: cpu 775 ddr 650 ahb 258
Tap values = (0xf, 0xf, 0xf, 0xf)
128 MB
Top of RAM usable for U-Boot at: 88000000
Reserving 410k for U-Boot at: 87f98000
Reserving 192k for malloc() at: 87f68000
Reserving 44 Bytes for Board Info at: 87f67fd4
Reserving 36 Bytes for Global Data at: 87f67fb0
Reserving 128k for boot params() at: 87f47fb0
Stack Pointer at: 87f47f98
Now running in RAM - U-Boot at: 87f98000
Flash Manuf Id 0xc8, DeviceId0 0x40, DeviceId1 0x15
flash size 2MB, sector count = 32
Flash: 2 MB
*** Warning - bad CRC, using default environment
Power up PLL with outdiv = 0 then switch to 3
In: serial
Out: serial
Err: serial
Net: ath_gmac_enet_initialize...
No valid address in Flash. Using fixed address
ath_gmac_enet_initialize: reset mask:c02200
athr_mgmt_init (MDC/MDIO config)::done
Dragonfly ----> S17 PHY *
athrs17_reg_init: complete
Max resets limit reached exiting...
athr_gmac_sgmii_setup SGMII done
: cfg1 0x80000000 cfg2 0x7114
eth0: 00:03:7f:ff:ff:ff
ath_gmac_phy_setup
eth0 up
eth0
Qualcomm Atheros SPI NAND Driver, Version 0.1 (c) 2014 Qualcomm Atheros Inc.
ath_spi_nand_ecc: furture feat = 0x18
ath_spi_nand_ecc: middle feat = 0x18
zte ath_spi_nand_read_id 0xefaa
zte ath_spi_nand_read_id 0xefaa21
====== NAND Parameters ======
sc addr = 0x87ff7430 page(write size) = 0x800 (erase size) block = 0x20000
Setting 0x181162c0 to 0x4b962100
Uaztemain: enter into !
zte_getHandOffState: read data=0x20 from 0x0
Uaztemain: no need to update '˛š@J|šH*+śBdúśŕšÄµ'
Hit any key to stop autoboot: 2 0
ath> tftpboot 0x81000000 luci-21.02-snapshot-r16500-zte_mf286a-initramfs-kernel.bin
Trying eth0
ath_gmac_phy_link
ath_gmac_phy_duplex
ath_gmac_phy_speed
dup 1 speed 1000
Using eth0 device
TFTP from server 192.168.0.22; our IP address is 192.168.0.1
Filename 'luci-21.02-snapshot-r16500-zte_mf286a-initramfs-kernel.bin'.
Load address: 0x81000000
Loading: *#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################
done
Bytes transferred = 8406431 (80459f hex)
ath> bootm 0x81000000
## Booting image at 81000000 ...
Image Name: MIPS OpenWrt Linux-5.4.179
Created: 2022-02-22 19:29:39 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 8406367 Bytes = 8 MB
Load Address: 80060000
Entry Point: 80060000
Verifying Checksum at 0x81000040 ...OK
Uncompressing Kernel Image ... ERROR: LzmaDecode.c, 543
Decoding error = 1
LZMA ERROR 1 - must RESET board to recover
€
U-Boot 1.1.4 (Sep 27 2017 - 19:55:03)
ap152 - Dragonfly 1.0DRAM:
sri
ath_ddr_initial_config(278): (ddr2 init)
ath_sys_frequency: cpu 775 ddr 650 ahb 258
Tap values = (0xf, 0xf, 0xf, 0xf)
128 MB
Top of RAM usable for U-Boot at: 88000000
Reserving 410k for U-Boot at: 87f98000
Reserving 192k for malloc() at: 87f68000
Reserving 44 Bytes for Board Info at: 87f67fd4
Reserving 36 Bytes for Global Data at: 87f67fb0
Reserving 128k for boot params() at: 87f47fb0
Stack Pointer at: 87f47f98
Now running in RAM - U-Boot at: 87f98000
Flash Manuf Id 0xc8, DeviceId0 0x40, DeviceId1 0x15
flash size 2MB, sector count = 32
Flash: 2 MB
*** Warning - bad CRC, using default environment
Power up PLL with outdiv = 0 then switch to 3
In: serial
Out: serial
Err: serial
Net: ath_gmac_enet_initialize...
No valid address in Flash. Using fixed address
ath_gmac_enet_initialize: reset mask:c02200
athr_mgmt_init (MDC/MDIO config)::done
Dragonfly ----> S17 PHY *
athrs17_reg_init: complete
Max resets limit reached exiting...
athr_gmac_sgmii_setup SGMII done
: cfg1 0x80000000 cfg2 0x7114
eth0: 00:03:7f:ff:ff:ff
ath_gmac_phy_setup
eth0 up
eth0
Qualcomm Atheros SPI NAND Driver, Version 0.1 (c) 2014 Qualcomm Atheros Inc.
ath_spi_nand_ecc: furture feat = 0x18
ath_spi_nand_ecc: middle feat = 0x18
zte ath_spi_nand_read_id 0xefaa
zte ath_spi_nand_read_id 0xefaa21
====== NAND Parameters ======
sc addr = 0x87ff7430 page(write size) = 0x800 (erase size) block = 0x20000
Setting 0x181162c0 to 0x4b962100
Uaztemain: enter into !
zte_getHandOffState: read data=0x20 from 0x0
Uaztemain: no need to update '˛š@J|šH*+śBdúśŕšÄµ'
Hit any key to stop autoboot: 2 1 0
Loading from device 0: ath-spi-nand (offset 0x1800000)
Image Name: MIPS OpenWrt Linux-5.4.171
Created: 2022-02-10 19:06:04 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 2157186 Bytes = 2.1 MB
Load Address: 80060000
Entry Point: 80060000
## Booting image at 81000000 ...
Image Name: MIPS OpenWrt Linux-5.4.171
Created: 2022-02-10 19:06:04 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 2157186 Bytes = 2.1 MB
Load Address: 80060000
Entry Point: 80060000
Verifying Checksum at 0x81000040 ...OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80060000) ...
## Giving linux memsize in bytes, 134217728
Starting kernel ...
[ 0.000000] Linux version 5.4.171 (cezary@eko.one.pl) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r15816-b95f3caaa1)) #0 Thu Feb 10 19:06:04 2022
[ 0.000000] printk: bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019750 (MIPS 74Kc)
[ 0.000000] MIPS: machine is ZTE MF286A
[ 0.000000] SoC: Qualcomm Atheros QCA956X ver 1 rev 0
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32480
[ 0.000000] Kernel command line: console=ttyS0,115200n8 rootfstype=squashfs,jffs2
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 121920K/131072K available (5518K kernel code, 180K rwdata, 708K rodata, 1200K init, 210K bss, 9152K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 51
[ 0.000000] random: get_random_bytes called from 0x806a4a28 with crng_init=0
[ 0.000000] CPU clock: 775.000 MHz
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4932285024 ns
[ 0.000007] sched_clock: 32 bits at 387MHz, resolution 2ns, wraps every 5541893118ns
[ 0.008228] Calibrating delay loop... 385.02 BogoMIPS (lpj=770048)
[ 0.046723] pid_max: default: 32768 minimum: 301
[ 0.051726] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.059444] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.071758] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.082053] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[ 0.089339] pinctrl core: initialized pinctrl subsystem
[ 0.096095] NET: Registered protocol family 16
[ 0.102423] GPIO line 19 (led:wlan) hogged as output/high
[ 0.133767] clocksource: Switched to clocksource MIPS
[ 0.140000] thermal_sys: Registered thermal governor 'step_wise'
[ 0.140351] NET: Registered protocol family 2
[ 0.151458] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.159799] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 0.168688] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.176784] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.184235] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.191060] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.198006] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.205629] NET: Registered protocol family 1
[ 0.210282] PCI: CLS 0 bytes, default 32
[ 0.218133] workingset: timestamp_bits=14 max_order=15 bucket_order=1
[ 0.231328] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.237521] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.261221] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 0.272461] pinctrl-single 1804002c.pinmux: 544 pins, size 68
[ 0.279561] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.288340] printk: console [ttyS0] disabled
[ 0.292932] 18020000.uart: ttyS0 at MMIO 0x18020000 (irq = 9, base_baud = 1562500) is a 16550A
[ 0.302046] printk: console [ttyS0] enabled
[ 0.302046] printk: console [ttyS0] enabled
[ 0.311108] printk: bootconsole [early0] disabled
[ 0.311108] printk: bootconsole [early0] disabled
[ 0.331194] spi-nand spi0.1: Winbond SPI NAND was found.
[ 0.336738] spi-nand spi0.1: 128 MiB, block size: 128 KiB, page size: 2048, OOB size: 64
[ 0.346221] 6 fixed-partitions partitions found on MTD device spi0.1
[ 0.352834] Creating 6 MTD partitions on "spi0.1":
[ 0.357804] 0x000000000000-0x0000000a0000 : "fota-flag"
[ 0.364592] 0x0000000a0000-0x000000120000 : "art"
[ 0.371681] 0x000000120000-0x0000001a0000 : "mac"
[ 0.378832] 0x0000001a0000-0x000001800000 : "ubiconcat0"
[ 0.404640] 0x000001800000-0x000001c00000 : "kernel"
[ 0.414761] 0x000001c00000-0x000008000000 : "ubiconcat1"
[ 0.508736] spi-nor spi0.0: gd25q16 (2048 Kbytes)
[ 0.513681] 3 fixed-partitions partitions found on MTD device spi0.0
[ 0.520261] Creating 3 MTD partitions on "spi0.0":
[ 0.525227] 0x000000000000-0x0000000a0000 : "u-boot"
[ 0.531234] 0x0000000a0000-0x0000000c0000 : "u-boot-env"
[ 0.537604] 0x0000000c0000-0x000000200000 : "reserved1"
[ 0.544113] Concatenating MTD devices:
[ 0.548040] (0): "ubiconcat0"
[ 0.551115] (1): "ubiconcat1"
[ 0.554185] into device "ubi-concat"
[ 0.557910] 1 fixed-partitions partitions found on MTD device ubi-concat
[ 0.564836] Creating 1 MTD partitions on "ubi-concat":
[ 0.570155] 0x000000000000-0x000007a60000 : "ubi"
[ 0.577016] libphy: Fixed MDIO Bus: probed
[ 1.149761] random: fast init done
[ 1.218132] libphy: ag71xx_mdio: probed
[ 1.225207] switch0: Atheros AR8337 rev. 2 switch registered on mdio.0
[ 1.813264] ag71xx 19000000.eth: connected to PHY at mdio.0:00 [uid=004dd036, driver=Atheros AR8216/AR8236/AR8316]
[ 1.824547] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode: sgmii
[ 1.833057] NET: Registered protocol family 10
[ 1.842304] Segment Routing with IPv6
[ 1.846243] NET: Registered protocol family 17
[ 1.850934] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 1.864324] 8021q: 802.1Q VLAN Support v1.8
[ 1.870972] PCI host bridge /ahb/pcie-controller@18250000 ranges:
[ 1.877335] MEM 0x0000000012000000..0x0000000013ffffff
[ 1.882754] IO 0x0000000000000000..0x0000000000000000
[ 1.888317] PCI host bridge to bus 0000:00
[ 1.892595] pci_bus 0000:00: root bus resource [mem 0x12000000-0x13ffffff]
[ 1.899710] pci_bus 0000:00: root bus resource [io 0x0000]
[ 1.905479] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[ 1.912501] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 1.920719] pci 0000:00:00.0: [168c:0056] type 00 class 0x028000
[ 1.926979] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[ 1.934122] pci 0000:00:00.0: PME# supported from D0 D3hot
[ 1.940811] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[ 1.947697] pci 0000:00:00.0: BAR 0: assigned [mem 0x12000000-0x121fffff 64bit]
[ 1.957695] UBI: auto-attach mtd9
[ 1.961188] ubi0: attaching mtd9
[ 3.874242] ubi0: scanning is finished
[ 3.902967] ubi0: attached mtd9 (name "ubi", size 122 MiB)
[ 3.908679] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 3.915794] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 3.922811] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 3.930003] ubi0: good PEBs: 978, bad PEBs: 1, corrupted PEBs: 0
[ 3.936212] ubi0: user volume: 0, internal volumes: 1, max. volumes count: 128
[ 3.943678] ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 506101633
[ 3.953022] ubi0: available PEBs: 955, total reserved PEBs: 23, PEBs reserved for bad PEB handling: 19
[ 3.962973] ubi0: background thread "ubi_bgt0d" started, PID 386
[ 3.969559] /dev/root: Can't open blockdev
[ 3.973851] VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6
[ 3.981585] Please append a correct "root=" boot option; here are the available partitions:
[ 3.990221] 1f00 640 mtdblock0
[ 3.990224] (driver?)
[ 3.996982] 1f01 512 mtdblock1
[ 3.996984] (driver?)
[ 4.003744] 1f02 512 mtdblock2
[ 4.003746] (driver?)
[ 4.010509] 1f03 22912 mtdblock3
[ 4.010511] (driver?)
[ 4.017266] 1f04 4096 mtdblock4
[ 4.017268] (driver?)
[ 4.024030] 1f05 102400 mtdblock5
[ 4.024032] (driver?)
[ 4.030795] 1f06 640 mtdblock6
[ 4.030797] (driver?)
[ 4.037552] 1f07 128 mtdblock7
[ 4.037554] (driver?)
[ 4.044308] 1f08 1280 mtdblock8
[ 4.044310] (driver?)
[ 4.051072] 1f09 125312 mtdblock9
[ 4.051074] (driver?)
[ 4.057835] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[ 4.066368] Rebooting in 1 seconds..
€
U-Boot 1.1.4 (Sep 27 2017 - 19:55:03)
ap152 - Dragonfly 1.0DRAM:
sri
ath_ddr_initial_config(278): (ddr2 init)
ath_sys_frequency: cpu 775 ddr 650 ahb 258
Tap values = (0xf, 0xf, 0xf, 0xf)
128 MB
Top of RAM usable for U-Boot at: 88000000
Reserving 410k for U-Boot at: 87f98000
Reserving 192k for malloc() at: 87f68000
Reserving 44 Bytes for Board Info at: 87f67fd4
Reserving 36 Bytes for Global Data at: 87f67fb0
Reserving 128k for boot params() at: 87f47fb0
Stack Pointer at: 87f47f98
Now running in RAM - U-Boot at: 87f98000
Flash Manuf Id 0xc8, DeviceId0 0x40, DeviceId1 0x15
flash size 2MB, sector count = 32
Flash: 2 MB
*** Warning - bad CRC, using default environment
Power up PLL with outdiv = 0 then switch to 3
In: serial
Out: serial
Err: serial
Net: ath_gmac_enet_initialize...
No valid address in Flash. Using fixed address
ath_gmac_enet_initialize: reset mask:c02200
athr_mgmt_init (MDC/MDIO config)::done
Dragonfly ----> S17 PHY *
athrs17_reg_init: complete
Max resets limit reached exiting...
athr_gmac_sgmii_setup SGMII done
: cfg1 0x80000000 cfg2 0x7114
eth0: 00:03:7f:ff:ff:ff
ath_gmac_phy_setup
eth0 up
eth0
Qualcomm Atheros SPI NAND Driver, Version 0.1 (c) 2014 Qualcomm Atheros Inc.
ath_spi_nand_ecc: furture feat = 0x18
ath_spi_nand_ecc: middle feat = 0x18
zte ath_spi_nand_read_id 0xefaa
zte ath_spi_nand_read_id 0xefaa21
====== NAND Parameters ======
sc addr = 0x87ff7430 page(write size) = 0x800 (erase size) block = 0x20000
Setting 0x181162c0 to 0x4b962100
Uaztemain: enter into !
zte_getHandOffState: read data=0x20 from 0x0
Uaztemain: no need to update '˛š@J|šH*+śBdúśŕšÄµ'
Hit any key to stop autoboot: 2 1 0
ath> Ale nie używaj initramfs od luci bo jest za duzy. Użyj zwykłe initramfs od czystego obrazu.
aaaa, dobra, juz rrozumiem.
Zobaczymym co zrobi po sysupgrade potem
Robię dla wujka 286A i napotkałem problem
Uzywamy tam pptp ale nijak nie mogę go ustawić przy dodawaniu interfejsu
Chyba wszystko zainstalowałem związane z pptp co potrzeba a on się nie pojawia w dostepnych interfejsach 
Więc pokaż co zainstalowałeś.
Strony Poprzednia 1 … 12 13 14 15 16 … 21 Następna
Zaloguj się lub zarejestruj by napisać odpowiedź
eko.one.pl → Sprzęt / Hardware → ZTE MF286A - Openwrt
Forum oparte o PunBB, wspierane przez Informer Technologies, Inc