Temat: ZTE MF286R - OpenWrt
Czy ktoś ma ten sprzęt? Czy ktoś rozbierał, ma rzuty partycji itd?
Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.
Zaloguj się lub zarejestruj by napisać odpowiedź
Nie jesteś zalogowany. Proszę się zalogować lub zarejestrować.
ZTE MF286R - OpenWrt (Strona 1 z 50)
eko.one.pl → Sprzęt / Hardware → ZTE MF286R - OpenWrt
Posty: 1 do 25 z 1,243
- onken
- Użytkownik
- Nieaktywny
Odp: ZTE MF286R - OpenWrt
@Cezary
Dzisiaj odbieram "R"
Napisz mi proszę co podać z konsoli UART to chętnie pomogę.
Odp: ZTE MF286R - OpenWrt
Na początek może cały bootlog oraz wyniki poleceń:
uname -a
cat /proc/cpuinfo
cat /sys/kernel/debug/usb/devices
cat /proc/mtd
Odp: ZTE MF286R - OpenWrt
Dokładnie tak.
Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.
- onken
- Użytkownik
- Nieaktywny
Odp: ZTE MF286R - OpenWrt
Ok. Pod wieczór zrobię 
Może wcześniej.
A jak zalogować bootlog bo z konsoli nie będzie chyba jak skopiować chyba 
Odp: ZTE MF286R - OpenWrt
Jak używasz putty to tam w opcjach jest logowanie do pliku. A tak w ogóle to możesz myszą zaznaczyć tekst.
Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.
- onken
- Użytkownik
- Nieaktywny
Odp: ZTE MF286R - OpenWrt
U-Boot 1.1.4 (Jun 25 2019 - 11:21:44)
ap152 - Dragonfly 1.0DRAM:
sri
ath_ddr_initial_config(278): (ddr2 init)
ath_sys_frequency: cpu 775 ddr 650 ahb 258
Tap values = (0x11, 0x11, 0x11, 0x11)
128 MB
Top of RAM usable for U-Boot at: 88000000
Reserving 409k for U-Boot at: 87f98000
Reserving 192k for malloc() at: 87f68000
Reserving 44 Bytes for Board Info at: 87f67fd4
Reserving 36 Bytes for Global Data at: 87f67fb0
Reserving 128k for boot params() at: 87f47fb0
Stack Pointer at: 87f47f98
Now running in RAM - U-Boot at: 87f98000
Flash Manuf Id 0xc8, DeviceId0 0x40, DeviceId1 0x15
flash size 2MB, sector count = 32
Flash: 2 MB
*** Warning - bad CRC, using default environment
Power up PLL with outdiv = 0 then switch to 3
In: serial
Out: serial
Err: serial
Net: ath_gmac_enet_initialize...
No valid address in Flash. Using fixed address
ath_gmac_enet_initialize: reset mask:c02200
athr_mgmt_init (MDC/MDIO config)::done
Dragonfly ----> S17 PHY *
athrs17_reg_init: complete
Max resets limit reached exiting...
athr_gmac_sgmii_setup SGMII done
: cfg1 0x80000000 cfg2 0x7114
eth0: 00:03:7f:ff:ff:ff
ath_gmac_phy_setup
eth0 up
eth0
Qualcomm Atheros SPI NAND Driver, Version 0.1 (c) 2014 Qualcomm Atheros Inc.
ath_spi_nand_ecc: furture feat = 0x10
ath_spi_nand_ecc: middle feat = 0x10
zte ath_spi_nand_read_id 0xc8d1
zte ath_spi_nand_read_id 0xc8d1c8
zte debug gd 128 oob
====== NAND Parameters ======
sc addr = 0x87ff7290 page(write size) = 0x800 (erase size) block = 0x20000
Setting 0x181162c0 to 0x4b962100
Uaztemain: enter into !
zte_getHandOffState: read data=0xff from 0x0
Uaztemain: no need to update '▒'
Hit any key to stop autoboot:
8 2022-02-15 16:18:30 (edytowany przez onken 2022-02-15 16:23:32)
- onken
- Użytkownik
- Nieaktywny
Odp: ZTE MF286R - OpenWrt
próbuje z reszta ale bez zatrzymania ubota on ciągle pluje i nie ma jak wpisac i odczytać sobie te komendy
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2022.02.15 16:20:58 =~=~=~=~=~=~=~=~=~=~=~=
ŕ
U-Boot 1.1.4 (Jun 25 2019 - 11:21:44)
ap152 - Dragonfly 1.0DRAM:
sri
ath_ddr_initial_config(278): (ddr2 init)
ath_sys_frequency: cpu 775 ddr 650 ahb 258
Tap values = (0x10, 0x10, 0x10, 0x10)
128 MB
Top of RAM usable for U-Boot at: 88000000
Reserving 409k for U-Boot at: 87f98000
Reserving 192k for malloc() at: 87f68000
Reserving 44 Bytes for Board Info at: 87f67fd4
Reserving 36 Bytes for Global Data at: 87f67fb0
Reserving 128k for boot params() at: 87f47fb0
Stack Pointer at: 87f47f98
Now running in RAM - U-Boot at: 87f98000
Flash Manuf Id 0xc8, DeviceId0 0x40, DeviceId1 0x15
flash size 2MB, sector count = 32
Flash: 2 MB
*** Warning - bad CRC, using default environment
Power up PLL with outdiv = 0 then switch to 3
In: serial
Out: serial
Err: serial
Net: ath_gmac_enet_initialize...
No valid address in Flash. Using fixed address
ath_gmac_enet_initialize: reset mask:c02200
athr_mgmt_init (MDC/MDIO config)::done
Dragonfly ----> S17 PHY *
athrs17_reg_init: complete
Max resets limit reached exiting...
athr_gmac_sgmii_setup SGMII done
: cfg1 0x80000000 cfg2 0x7114
eth0: 00:03:7f:ff:ff:ff
ath_gmac_phy_setup
eth0 up
eth0
Qualcomm Atheros SPI NAND Driver, Version 0.1 (c) 2014 Qualcomm Atheros Inc.
ath_spi_nand_ecc: furture feat = 0x10
ath_spi_nand_ecc: middle feat = 0x10
zte ath_spi_nand_read_id 0xc8d1
zte ath_spi_nand_read_id 0xc8d1c8
zte debug gd 128 oob
====== NAND Parameters ======
sc addr = 0x87ff7290 page(write size) = 0x800 (erase size) block = 0x20000
Setting 0x181162c0 to 0x4b962100
Uaztemain: enter into !
zte_getHandOffState: read data=0xff from 0x0
Uaztemain: no need to update 'ç'
Hit any key to stop autoboot: 2 1 0
Loading from device 0: ath-spi-nand (offset 0x1800000)
Image Name: MIPS OpenWrt Linux-3.3.8
Created: 2021-05-12 21:57:49 UTC
Image Type: MIPS Linux Multi-File Image (lzma compressed)
Data Size: 1210115 Bytes = 1.2 MB
Load Address: 80060000
Entry Point: 80060000
Contents:
Image 0: 1210107 Bytes = 1.2 MB
ath_spi_nand_page_read :status=0x1
ath_spi_nand_page_read :status=0x1
ath_spi_nand_page_read :status=0x1
## Booting image at 81000000 ...
Image Name: MIPS OpenWrt Linux-3.3.8
Created: 2021-05-12 21:57:49 UTC
Image Type: MIPS Linux Multi-File Image (lzma compressed)
Data Size: 1210115 Bytes = 1.2 MB
Load Address: 80060000
Entry Point: 80060000
Contents:
Image 0: 1210107 Bytes = 1.2 MB
Verifying Checksum at 0x81000040 ...OK
Uncompressing Multi-File Image ... OK
No initrd
## Transferring control to Linux (at address 80060000) ...
## Giving linux memsize in bytes, 134217728
Starting kernel ...
[ 0.000000] Linux version 3.3.8 (scl@scl_xa243_241) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Thu May 13 05:57:02 CST 2021
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019750 (MIPS 74Kc)
[ 0.000000] SoC: Qualcomm Atheros QCA956X rev 0
[ 0.000000] Clocks: CPU:775.000MHz, DDR:650.000MHz, AHB:258.333MHz, Ref:25.000MHz
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] User-defined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00008000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] Early memory PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00008000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: board=AP152 console=ttyS0,115200 mtdparts=spi0.0:640k(u-boot),128k(u-boot-env),1280k(reserved1);spi0.1:640k(fota-flag),512k(art),512k(mac),768k(reserved2),4m(cfg-param),4m(log),640k(oops),5m(reserved3),8m(web),3m(kernel),26m(rootfs),25m(data),50m(fota),29m@0x1800000(firmware) mem=128M rootfstype=squashfs,jffs2 noinitrd crashkernel=10M@20M oops=panic
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 125784k/131072k available (2574k kernel code, 5288k reserved, 687k data, 228k init, 0k highmem)
[ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:83
[ 0.000000] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[ 0.060000] pid_max: default: 32768 minimum: 301
[ 0.060000] Mount-cache hash table entries: 512
[ 0.060000] Performance counters: mips/74K PMU enabled, 4 32-bit counters available to each CPU, irq 13
[ 0.070000] NET: Registered protocol family 16
[ 0.080000] gpiochip_add: registered GPIOs 0 to 22 on device: ath79
[ 0.080000] MIPS: machine is Qualcomm Atheros AP152 reference board
[ 0.090000]
[ 0.090000] WLAN firmware dump buffer allocation of 2097152 bytes @ address 0x87a00000- SUCCESS !!!
[ 0.100000] registering PCI controller with io_map_base unset
[ 0.310000] bio: create slab <bio-0> at 0
[ 0.310000] PCI host bridge to bus 0000:00
[ 0.320000] pci_bus 0000:00: root bus resource [mem 0x12000000-0x13ffffff]
[ 0.320000] pci_bus 0000:00: root bus resource [io 0x0001]
[ 0.330000] pci 0000:00:00.0: BAR 0: assigned [mem 0x12000000-0x121fffff 64bit]
[ 0.330000] pci 0000:00:00.0: using irq 40 for pin 1
[ 0.340000] Switching to clocksource MIPS
[ 0.340000] NET: Registered protocol family 2
[ 0.350000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.350000] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.360000] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.360000] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.370000] TCP reno registered
[ 0.370000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.380000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.380000] NET: Registered protocol family 1
[ 0.400000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.400000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.410000] msgmni has been set to 245
[ 0.420000] io scheduler noop registered
[ 0.420000] io scheduler deadline registered (default)
[ 0.430000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.450000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[ 0.460000] console [ttyS0] enabled, bootconsole disabled
[ 0.460000] console [ttyS0] enabled, bootconsole disabled
[ 0.470000] m25p80 spi0.0: found gd25q16csig, expected m25p80
[ 0.480000] m25p80 spi0.0: gd25q16csig (2048 Kbytes)
[ 0.490000] 3 cmdlinepart partitions found on MTD device spi0.0
[ 0.490000] Creating 3 MTD partitions on "spi0.0":
[ 0.500000] 0x000000000000-0x0000000a0000 : "u-boot"
[ 0.500000] 0x0000000a0000-0x0000000c0000 : "u-boot-env"
[ 0.510000] 0x0000000c0000-0x000000200000 : "reserved1"
[ 0.520000] zte gd nand
[ 0.520000] NAND device: Manufacturer ID: 0xc8, Chip ID: 0xd1 (Giga Device NAND 128MiB 3,3V 8-bit)
[ 0.530000] Scanning device for bad blocks
[ 0.740000] Bad eraseblock 1023 at 0x000007fe0000
[ 0.750000] 14 cmdlinepart partitions found on MTD device spi0.1
[ 0.750000] Creating 14 MTD partitions on "spi0.1":
[ 0.760000] 0x000000000000-0x0000000a0000 : "fota-flag"
[ 0.760000] 0x0000000a0000-0x000000120000 : "art"
[ 0.770000] 0x000000120000-0x0000001a0000 : "mac"
[ 0.780000] 0x0000001a0000-0x000000260000 : "reserved2"
[ 0.780000] 0x000000260000-0x000000660000 : "cfg-param"
[ 0.790000] 0x000000660000-0x000000a60000 : "log"
[ 0.790000] 0x000000a60000-0x000000b00000 : "oops"
[ 0.800000] 0x000000b00000-0x000001000000 : "reserved3"
[ 0.810000] 0x000001000000-0x000001800000 : "web"
[ 0.810000] 0x000001800000-0x000001b00000 : "kernel"
[ 0.820000] 0x000001b00000-0x000003500000 : "rootfs"
[ 0.830000] mtd: partition "rootfs" set to be root filesystem
[ 0.830000] 0x000003500000-0x000004e00000 : "data"
[ 0.840000] 0x000004e00000-0x000008000000 : "fota"
[ 0.840000] 0x000001800000-0x000003500000 : "firmware"
[ 0.990000] ag71xx_mdio: probed
[ 0.990000] zte_nand_local_read():Reading Flash for Calibraton data from 0x0 and partition name is mac
[ 1.000000] ***********************************************
[ 1.010000] AG71XX using MAC@ - using c8:ea:f8:a8:fe:92
[ 1.020000] ***********************************************
[ 1.020000] eth0: Atheros AG71xx at 0xb9000000, irq 4
[ 1.600000] eth0: Atheros AR8327 switch driver attached.
[ 4.500000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd036, driver=Atheros AR8216/AR8236/AR8316]
[ 4.510000] *************tian.zb test err=0***********************
[ 4.520000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled/input/input0
[ 4.530000] zte gpio_keys_polled_check_state:report code=358 state=0
[ 4.530000] zte gpio_keys_polled_check_state:report code=352 state=0
[ 4.540000] zte gpio_keys_polled_check_state:report code=238 state=0
[ 4.550000] netem: version 1.3
[ 4.550000] u32 classifier
[ 4.550000] Performance counters on
[ 4.560000] input device check on
[ 4.560000] Actions configured
[ 4.560000] TCP cubic registered
[ 4.570000] NET: Registered protocol family 17
[ 4.570000] 8021q: 802.1Q VLAN Support v1.8
[ 4.580000] ### of_selftest(): No testcase data in device tree; not running tests
[ 4.610000] VFS: Mounted root (squashfs filesystem) readonly on device 31:13.
[ 4.620000] Freeing unused kernel memory: 228k freed
init started: BusyBox v1.19.4 (2021-05-13 04:17:46 CST)
*****************ZTE rcS********************
call startup scripts here\n
[ 11.160000] ssdk_plat_init start
[ 11.160000] Register QCA PHY driver
[ 11.160000] PHY ID is 0x4dd036
[ 11.270000] qca probe f1 phy driver succeeded!
[ 11.270000] qca-ssdk module init succeeded!
[ 11.820000] NET: Registered protocol family 10
[ 12.230000] SCSI subsystem initialized
[ 12.860000] usbcore: registered new interface driver usbfs
[ 12.870000] usbcore: registered new interface driver hub
[ 12.870000] usbcore: registered new device driver usb
[ 12.890000] Button Hotplug driver version 0.4.1
[ 13.240000] NTFS driver 2.1.30 [Flags: R/O MODULE].
[ 13.560000] Error: Driver 'gpio-keys-polled' is already registered, aborting...
[ 13.980000] PPP generic driver version 2.4.2
[ 14.230000] tun: Universal TUN/TAP device driver, 1.6
[ 14.240000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 14.270000] NET: Registered protocol family 24
[ 14.350000] bonding: Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
[ 14.420000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 14.720000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 14.730000] ehci-platform ehci-platform.0: Generic Platform EHCI Controller
[ 14.740000] ehci-platform ehci-platform.0: new USB bus registered, assigned bus number 1
[ 14.770000] ehci-platform ehci-platform.0: irq 48, io mem 0x1b000000
[ 14.790000] ehci-platform ehci-platform.0: USB 2.0 started, EHCI 1.00
[ 14.790000] hub 1-0:1.0: USB hub found
[ 14.800000] hub 1-0:1.0: 1 port detected
[ 14.800000] ehci-platform ehci-platform.1: Generic Platform EHCI Controller
[ 14.810000] ehci-platform ehci-platform.1: new USB bus registered, assigned bus number 2
[ 14.850000] ehci-platform ehci-platform.1: irq 49, io mem 0x1b400000
[ 14.870000] ehci-platform ehci-platform.1: USB 2.0 started, EHCI 1.00
[ 14.870000] hub 2-0:1.0: USB hub found
[ 14.880000] hub 2-0:1.0: 1 port detected
[ 15.120000] usb 1-1: new high-speed USB device number 2 using ehci-platform
[ 15.220000] nf_conntrack version 0.5.0 (1968 buckets, 7872 max)
[ 15.600000] ZTE Generic Netlink Module Inserted without Lock
[ 15.660000] xt_time: kernel timezone is -0000
[ 16.080000] nf_conntrack_rtsp v0.6.21 loading
[ 16.090000] nf_nat_rtsp v0.6.21 loading
[ 16.170000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 16.330000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 16.760000] AR71XX_RESET_REG_WDOG_CTRL: 0x0
[ 16.760000]
[ 16.840000] cdc_acm 1-1:1.2: This device cannot do calls on its own. It is not a modem.
[ 16.850000] cdc_acm 1-1:1.2: ttyACM0: USB ACM device
[ 16.850000] usbcore: registered new interface driver cdc_acm
[ 16.860000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 16.950000] usbcore: registered new interface driver usbserial
[ 16.950000] USB Serial support registered for generic
[ 16.960000] usbcore: registered new interface driver usbserial_generic
[ 16.960000] usbserial: USB Serial Driver core
[ 17.020000] Initializing USB Mass Storage driver...
[ 17.020000] usbcore: registered new interface driver usb-storage
[ 17.030000] USB Mass Storage support registered.
[ 17.050000] driver_info->flags 1020 idVendor 19d2 idProduct 1489
[ 17.060000] cdc_ether 1-1:1.6: ecm0: register 'cdc_ether' at usb-ehci-platform.0-1, CDC Ethernet Device, 32:8a:4a:66:e5:67
[ 17.070000] usbcore: registered new interface driver cdc_ether
[ 17.150000] generic_rndis_bind: rx_urb_size: 0x3e80
[ 17.150000] generic_rndis_bind: data zero copy=1
[ 17.160000] driver_info->flags 3238 idVendor 19d2 idProduct 1489
[ 17.170000] rndis_host 1-1:1.0: usb0: register 'rndis_host' at usb-ehci-platform.0-1, RNDIS device, 82:eb:a0:9a:9c:16
[ 17.180000] usbcore: registered new interface driver rndis_host
[ 17.250000] USB Serial support registered for GSM modem (1-port)
[ 17.250000] usbcore: registered new interface driver option
[ 17.260000] option: v0.7.2:USB Driver for GSM modems
[ 17.320000] fuse init (API version 7.18)
[ 18.110000] yaffs: dev is 32505864 name is "mtdblock8" rw
[ 18.120000] yaffs: passed flags ""
[ 18.160000] yaffs: dev is 32505871 name is "mtdblock15" rw
[ 18.160000] yaffs: passed flags ""
rm: can't remove '/etc_rw/fota/cp_failure_flag': No such file or directory
SOS: FLAG is mtdblock7
SOS: /etc_rw/fota/cfg_pa[ 19.490000] yaffs: dev is 32505863 name is "mtdblock7" rw
rtiton_flag has [ 19.500000] yaffs: passed flags ""
content
space usage of /etc_rw/config is 28%
[ 19.710000] yaffs: dev is 32505866 name is "mtdblock10" rw
[ 19.720000] yaffs: passed flags ""
SOS: /etc_rw/config use mtdblock7, /zte_backup use mtdblock10, now doing backup!
rm: can't remove '/zte_backup/lost+found': Directory not empty
[ 21.530000] Load cfg new driver...
[ 21.540000] cfg init, /home/scl/ci/workspace/Soft4_MF286R_TMOPL_CPE/qsdk/build_dir/linux-ar71xx_generic/cfg-1.0/cfg_param.c 578
[ 21.550000]
[ 21.550000] simcard_roam=Homecs
[ 21.550000] 73696d636172645f726f616d3d486f6d65006373
[ 21.660000]
[ 21.660000] cfg init end, /home/scl/ci/workspace/Soft4_MF286R_TMOPL_CPE/qsdk/build_dir/linux-ar71xx_generic/cfg-1.0/cfg_param.c 637
[ 21.670000] cfg init, /home/scl/ci/workspace/Soft4_MF286R_TMOPL_CPE/qsdk/build_dir/linux-ar71xx_generic/cfg-1.0/cfg_param.c 578
[ 21.680000]
[ 21.680000] TESTBITSIGNINFO=0000
[ 21.690000] 544553544249545349474e494e464f3d30303030
[ 21.690000]
[ 21.690000] cfg init end, /home/scl/ci/workspace/Soft4_MF286R_TMOPL_CPE/qsdk/build_dir/linux-ar71xx_generic/cfg-1.0/cfg_param.c 637
[ 21.710000] cfg init, /home/scl/ci/workspace/Soft4_MF286R_TMOPL_CPE/qsdk/build_dir/linux-ar71xx_generic/cfg-1.0/cfg_param.c 578
[ 21.720000] cfg driver error: /etc_rw/inic/cert open failure, file: /home/scl/ci/workspace/Soft4_MF286R_TMOPL_CPE/qsdk/build_dir/linux-ar71xx_generic/cfg-1.0/cfg_param.c, line: 857!
[ 21.740000]
[ 21.740000]
[ 21.740000] 0000000000000000000000000000000000000000
[ 21.750000]
[ 21.750000] cfg init end, /home/scl/ci/workspace/Soft4_MF286R_TMOPL_CPE/qsdk/build_dir/linux-ar71xx_generic/cfg-1.0/cfg_param.c 637
[ 21.760000] cfg init, /home/scl/ci/workspace/Soft4_MF286R_TMOPL_CPE/qsdk/build_dir/linux-ar71xx_generic/cfg-1.0/cfg_param.c 578
[ 21.770000] cfg driver error: /etc_rw/inic/wapi open failure, file: /home/scl/ci/workspace/Soft4_MF286R_TMOPL_CPE/qsdk/build_dir/linux-ar71xx_generic/cfg-1.0/cfg_param.c, line: 857!
[ 21.790000]
[ 21.790000]
[ 21.790000] 0000000000000000000000000000000000000000
[ 21.800000]
[ 21.800000] cfg init end, /home/scl/ci/workspace/Soft4_MF286R_TMOPL_CPE/qsdk/build_dir/linux-ar71xx_generic/cfg-1.0/cfg_param.c 637
[ 21.830000] usbcore: registered new interface driver cdc_wdm
[ 22.280000] usbcore: registered new interface driver qmi_wwan
mkdir: can't create directory '/dev/net': File exists
mknod: dev/net/tun: File exists
killall: syslogd: no process killed
*************ZTE Init Script*************
insmod: can't insert '/lib/modules/3.3.8/xt_time.ko': File exists
rmmod: can't unload 'shortcut_fe_drv': unknown symbol in module, or unknown parameter
[ 23.510000] ipt_TRIGGER: module license 'unspecified' taints kernel.
[ 23.510000] Disabling lock debugging due to kernel taint
[ 23.520000] iptables target:TRIGGER __init
[ 23.590000] usbcore: registered new interface driver cdc_ncm
enter is_fota_update_successed.
find a good block.
last find blk_num = 0
****fota_update_flag in /dev/mtd3 is ˙****
Unable to open pidfile /var/run/nvramd.pid: No such file or directory
reboot_schedule is disabled
Create bridge br0..........
monitor:add@/devices/virtual/net/br0
monitor:ACTION=add
monitor:DEVPATH=/devices/virtual/net/br0
monitor:SUBSYSTEM=net
monitor:DEVTYPE=bridge
monitor:INTERFACE=br0
monitor:IFINDEX=7
monitor:SEQNUM=630
monitor:event { 'add', '' }
monitor:add@/devices/virtual/net/br0/queues/tx-0
monitor:ACTION=add
monitor:DEVPATH=/devices/virtual/net/br0/queues/tx-0
monitor:SUBSYSTEM=queues
monitor:SEQNUM=631
monitor:event { 'add', '' }
/etc/init.d/rcS: /etc/init.d/zte_init.sh: line 85: telnetd: not found
[ 36.030000] ADDRCONF(NETDEV_UP): eth0: link is not ready
* daemon not running. starting it now on port 5037 *
enter launch_server server_port is 5037
launch_server pipe path & pid: /usr/bin/adb, 762
launch_server pipe path & pid: /usr/bin/adb, 0
pid=0 and server_port is : 5037
launch_server temp value: O,K,
* daemon started successfully *
goahead initWebs info: webdir is /etc_ro/web/web!
webs: Listening for HTTP requests at address 192.168.0.1
SSDK Init OK!
operate done.
SSDK Init OK!
operate done.
SSDK Init OK!
operate done.
SSDK Init OK!
operate done.
SSDK Init OK!
operate done.
SSDK Init OK!
operate done.
SSDK Init OK!
operate done.
SSDK Init OK!
operate done.
SSDK Init OK!
operate done.
SSDK Init OK!
operate done.
SSDK Init OK!
operate done.
SSDK Init OK!
operate done.
SSDK Init OK!
operate done.
SSDK Init OK!
operate done.
SSDK Init OK!
operate done.
SSDK Init OK!
operate done.
SSDK Init OK!
operate done.
SSDK Init OK!
operate done.
SSDK Init OK![ 37.740000] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 37.740000] eth0: link up (1000Mbps/Full duplex)
[ 37.750000]
[ 37.750000] /home/scl/ci/workspace/Soft4_MF286R_TMOPL_CPE/qsdk/build_dir/linux-ar71xx_generic/zte_genl_kernel-1.0/zte_genl_kernel_main.c[177]: ERROR:Build msg struct failed, snd_pid=-1, genl_switch=1!
operate done.
SSDK Init OK!
operate done.
SSDK Init OK!
operate done.
SSDK Init OK!
operate done.
SSDK Init OK!
operate done.
SSDK Init OK!
operate done.
monitor:add@/devices/virtual/net/eth0.1
monitor:ACTION=add
monitor:DEVPATH=/devices/virtual/net/eth0.1
monitor:SUBSYSTEM=net
monitor:INTERFACE=eth0.1
monitor:IFINDEX=8
monitor:SEQNUM=632
monitor:event { 'add', '' }
monitor:add@/devices/virtual/net/eth0.1/queues/tx-0
monitor:ACTION=add
monitor:DEVPATH=/devices/virtual/net/eth0.1/queues/tx-0
monitor:SUBSYSTEM=queues
monitor:SEQNUM=633
monitor:event { 'add', '' }
monitor:add@/devices/virtual/net/eth0.2
monitor:ACTION=add
monitor:DEVPATH=/devices/virtual/net/eth0.2
monitor:SUBSYSTEM=net
monitor:INTERFACE=eth0.2
monitor:IFINDEX=9
monitor:SEQNUM=634
monitor:event { 'add', '' }
monitor:add@/devices/virtual/net/eth0.2/queues/tx-0
monitor:ACTION=add
monitor:DEVPATH=/devices/virtual/net/eth0.2/queues/tx-0
monitor:SUBSYSTEM=queues
monitor:SEQNUM=635
monitor:event { 'add', '' }
[ 38.770000] eth0: link up (1000Mbps/Full duplex)
[ 38.780000]
[ 38.780000] /home/scl/ci/workspace/Soft4_MF286R_TMOPL_CPE/qsdk/build_dir/linux-ar71xx_generic/zte_genl_kernel-1.0/zte_genl_kernel_main.c[177]: ERROR:Build msg struct failed, snd_pid=-1, genl_switch=1!
webs: Listening for HTTPS requests at port 443
opms_wan_ifname=usb0
LanIfName=br0
CURRENT WAN MODE:PPP
dual_core_board_if= ....
2 KB/s (146 bytes in 0.047s)
[ 40.160000]
[ 40.160000] /home/scl/ci/workspace/Soft4_MF286R_TMOPL_CPE/qsdk/build_dir/linux-ar71xx_generic/zte_genl_kernel-1.0/zte_genl_kernel_main.c[197]: INFO:Recv from userspace: [Connect request from userspace
[ 40.170000] ]
[ 40.180000]
[ 40.180000] /home/scl/ci/workspace/Soft4_MF286R_TMOPL_CPE/qsdk/build_dir/linux-ar71xx_generic/zte_genl_kernel-1.0/zte_genl_kernel_main.c[169]: INFO:send msg to user ok, cmd=1, msg=1000
[ 40.200000]
[ 40.200000] /home/scl/ci/workspace/Soft4_MF286R_TMOPL_CPE/qsdk/build_dir/linux-ar71xx_generic/zte_genl_kernel-1.0/zte_genl_kernel_main.c[169]: INFO:send msg to user ok, cmd=3, msg=
zte_wifi_dfs_status_process: dfs=[]
iptables: No chain/target/match by that name.
internet.sh is called, the argument is []
killall: pppoecd: no process killed
killall: udhcpc: no process killed
killall: zte_router: no process killed
killall: zte_trx_router: no process killed
killall: udhcpd: no process killed
killall: dnsmasq: no process killed
killall: miniupnpd: no process killed
passwd: no record of admin in /etc/shadow, using /etc/passwd
Changing password for admin
New password:
Retype password:
Password for admin changed by admin
call setPortAsAllLAN............
lan_ip: 192.168.0.1, lan_netmask: 255.255.255.0..........
[ 41.590000] device eth0.1 entered promiscuous mode
[ 41.600000] device eth0 entered promiscuous mode
[ 41.600000] br0: port 1(eth0.1) entered forwarding state
[ 41.610000] br0: port 1(eth0.1) entered forwarding state
[ 41.620000] device eth0.2 entered promiscuous mode
[ 41.620000] br0: port 2(eth0.2) entered forwarding state
[ 41.630000] br0: port 2(eth0.2) entered forwarding state
opms_wan_ifname=usb0
[ 41.710000] br0: port 1(eth0.1) entered forwarding state
[ 41.730000] br0: port 2(eth0.2) entered forwarding state
opms_wan_ifname=usb0
LanIfName=br0
killall: udhcpd: no process killed
killall: dnsmasq: no process killed
begin
middle
else section
mang_num: -1
list_first_item:
one_num: -1
###the format of mac_ip_list is valid###
begin
middle
else section
mang_num: -1
list_first_item:
one_num: -1
###the format of mac_ip_list is valid###
opms_wan_ifname=usb0
LanIfName=br0
#######start the mtu_set.sh##########
#######end the mtu_set.sh##########
enter setVoipPortAsLAN()...
192.168.0.1255.255.255.0init_dns[ 43.980000] br0: port 2(eth0.2) entered disabled state
_ip:tmp_byte_net[ 43.990000] br0: port 1(eth0.1) entered disabled state
mask is 0
init_dns_ip:tmp_byte_netmask is 255
init_dns_ip:tmp_byte_netmask is 255
init_dns_ip:tmp_byte_netmask is 255
[ 44.010000] br0: port 2(eth0.2) entered forwarding state
[ 44.010000] br0: port 2(eth0.2) entered forwarding state
[ 44.020000] br0: port 1(eth0.1) entered forwarding state
[ 44.030000] br0: port 1(eth0.1) entered forwarding state
[ 44.110000] br0: port 2(eth0.2) entered forwarding state
zte_port_status_monitor_create_msg_queue(): msgid = [327690]
[ 44.130000] br0: port 1(eth0.1) entered forwarding state
Sat Jan 1 00:00:00 UTC 2000
opms_wan_ifname=usb0
LanIfName=br0
iptables v1.4.10: Couldn't load target `vpn_client_output':File not found
Try `iptables -h' or 'iptables --help' for more information.
/bin/sh: zte_user_connect: not found
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables v1.4.10: Couldn't load target `vpn_client_prerouting':File not found
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables v1.4.10: Couldn't load target `remote_mark':File not found
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables v1.4.10: Couldn't load target `filter_fw_level':File not found
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
ip6tables: No chain/target/match by that name.
ip6tables: No chain/target/match by that name.
ip6tables: No chain/target/match by that name.
ip6tables: No chain/target/match by that name.
ip6tables v1.4.10: Couldn't load target `filter_fw_level':File not found
Try `ip6tables -h' or 'ip6tables --help' for more information.
ip6tables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
tcp_detect_port_list: 53,123,1900,139,445,4719,80,443,7547
[ 48.190000] +++++++http_redirect load, g_web_redirect_gateway=[192.168.0.1]...
[ 48.190000] +++++++http_redirect load, g_web_redirect_mode=[http]...
monitor:add@/module/zte_http_redirect
monitor:ACTION=add
monitor:DEVPATH=/module/zte_http_redirect
monitor:SUBSYSTEM=module
monitor:SEQNUM=636
monitor:event { 'add', '' }
[ 48.290000] set 1
normal mode!
Please press Enter to activate this console. [ 48.430000]
[ 48.430000] /home/scl/ci/workspace/Soft4_MF286R_TMOPL_CPE/qsdk/build_dir/linux-ar71xx_generic/zte_genl_kernel-1.0/zte_genl_kernel_main.c[197]: INFO:Recv from userspace: [5]
/dev/mtdblock15 on /etc_rw/fota type yaffs2 (rw,relatime)
mtdblock15 already mounted!
opms_wan_ifname=usb0
LanIfName=br0
path: etc_rw...
enter the wifi_create_1 function
path: etc_rw...
enter the wifi_create_2 function
path: etc_rw...
enter the wifi_create_0 function
path: etc_rw...
enter the wifi_create_3 function
killall: miniupnpd: no process killed
[ 48.930000]
[ 48.930000] /home/scl/ci/workspace/Soft4_MF286R_TMOPL_CPE/qsdk/build_dir/linux-ar71xx_generic/zte_genl_kernel-1.0/zte_genl_kernel_main.c[197]: INFO:Recv from userspace: [5]
[ 49.030000]
[ 49.030000] /home/scl/ci/workspace/Soft4_MF286R_TMOPL_CPE/qsdk/build_dir/linux-ar71xx_generic/zte_genl_kernel-1.0/zte_genl_kernel_main.c[197]: INFO:Recv from userspace: [5]
opms_wan_ifname=usb0
LanIfName=br0
iptables: No chain/target/match by that name.
iptables v1.4.10: Couldn't load target `MINIUPNPD':File not found
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables v1.4.10: Couldn't load target `MINIUPNPD':File not found
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables v1.4.10: Couldn't load target `MINIUPNPD-POSTROUTING':File not found
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
killall: miniupnpd: no process killed
opms_wan_ifname=usb0
LanIfName=br0
iptables: No chain/target/match by that name.
iptables v1.4.10: Couldn't load target `MINIUPNPD':File not found
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables v1.4.10: Couldn't load target `MINIUPNPD':File not found
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables v1.4.10: Couldn't load target `MINIUPNPD-POSTROUTING':File not found
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
377+0 records in
377+0 records out
************start dos_attack_defender.sh*****************
iptables: No chain/target/match by that name.
iptables v1.4.10: Couldn't load target `dosattack_filter':File not found
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
************end dos_attack_defender.sh*****************
insmod: can't insert '/lib/modules/3.3.8/nf_conntrack_sip.ko': File exists
insmod: can't insert '/lib/modules/3.3.8/nf_nat_sip.ko': File exists
insmod: can't insert '/lib/modules/3.3.8/nf_conntrack_pptp.ko': File exists
insmod: can't insert '/lib/modules/3.3.8/nf_nat_pptp.ko': File exists
insmod: can't insert '/lib/modules/3.3.8/nf_conntrack_ftp.ko': File exists
insmod: can't insert '/lib/modules/3.3.8/nf_nat_ftp.ko': File exists
insmod: can't insert '/lib/modules/3.3.8/nf_conntrack_h323.ko': File exists
insmod: can't insert '/lib/modules/3.3.8/nf_nat_h323.ko': File exists
insmod: can't insert '/lib/modules/3.3.8/nf_conntrack_rtsp.ko': File exists
insmod: can't insert '/lib/modules/3.3.8/nf_nat_rtsp.ko': File exists
insmod: can't insert '/lib/modules/3.3.8/nf_conntrack_tftp.ko': File exists
insmod: can't insert '/lib/modules/3.3.8/nf_nat_tftp.ko': File exists
opms_wan_ifname=usb0
LanIfName=br0
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
ip6tables: No chain/target/match by that name.
377+0 records in
377+0 records out
iptables: Chain already exists.
[ 52.810000] __mm_init_module
monitor:add@/module/mem_manager
monitor:ACTION=add
monitor:DEVPATH=/module/mem_manager
monitor:SUBSYSTEM=module
monitor:SEQNUM=637
monitor:event { 'add', '' }
ip6tables: Chain already exists.
monitor:add@/module/asf
monitor:ACTION=add
monitor:DEVPATH=/module/asf
monitor:SUBSYSTEM=module
monitor:SEQNUM=638
monitor:event { 'add', '' }
monitor:add@/module/qdf
monitor:ACTION=add
monitor:DEVPATH=/module/qdf
monitor:SUBSYSTEM=module
monitor:SEQNUM=639
monitor:event { 'add', '[ 53.360000] ath_dfs: Version 2.0.0
[ 53.360000] Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved
' }
monitor:add@/module/ath_dfs
monitor:ACTION=add
monitor:DEVPATH=/module/ath_dfs
monitor:SUBSYSTEM=module
monitor:SEQNUM=640
monitor:event { 'add', '' }
00:00:09 UP>>[update_control.c:2950]########---Update_Control Start---########
tcp_detect_port_list: 53,123,1900,139,445,4719,80,443,7547
opms_wan_ifname=usb0
LanIfName=br0
00:00:10 UP>>[update_control.c:2952]modem is ASR_MODEM
killall: miniupnpd: no process killed
opms_wan_ifname=usb0
LanIfName=br0
iptables: No chain/target/match by that name.
iptables v1.4.10: Couldn't load target `MINIUPNPD':File not found
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables v1.4.10: Couldn't load target `MINIUPNPD':File not found
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables v1.4.10: Couldn't load target `MINIUPNPD-POSTROUTING':File not found
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
killall: miniupnpd: no process killed
opms_wan_ifname=usb0
LanIfName=br0
iptables: No chain/target/match by that name.
iptables v1.4.10: Couldn't load target `MINIUPNPD':File not found
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables v1.4.10: Couldn't load target `MINIUPNPD':File not found
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables v1.4.10: Couldn't load target `MINIUPNPD-POSTROUTING':File not found
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
************start dos_attack_defender.sh*****************
iptables: No chain/target/match by that name.
************end dos_attack_defender.sh*****************
iptables: Bad rule (does a matching rule exist in that chain?).
iptables: Bad rule (does a matching rule exist in that chain?).
remotemg_white_list=[]
enter add_remote_mgr_fw_items()
monitor:add@/module/umac
monitor:ACTION=add
monitor:DEVPATH=/module/umac
monitor:SUBSYSTEM=module
monitor:SEQNUM=641
monitor:event { 'add', '' }
add remote manager done.
enter add_telnet()
disable telnetd on lan side
firewall_sys_fw done
[ 58.100000] ath_hal: 0.9.17.1 (AR9380, REGOPS_FUNC, PRIVATE_DIAG, WRITE_EEPROM, 11D)
monitor:add@/module/ath_hal
monitor:ACTION=add
monitor:DEVPATH=/module/ath_hal
monitor:SUBSYSTEM=module
monitor:SEQNUM=642
monitor:event { 'add', '' }
iptables: Bad rule (does a matching rule exist in that chain?).
[ 58.220000] ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved
monitor:add@/module/ath_rate_atheros
monitor:ACTION=add
monitor:DEVPATH=/module/ath_rate_atheros
monitor:SUBSYSTEM=module
monitor:SEQNUM=643
monitor:event { 'add', '' }
[ 58.300000] ath_tx99: Version 2.0
[ 58.300000] Copyright (c) 2010 Atheros Communications, Inc, All Rights Reserved
monitor:add@/module/hst_tx99
monitor:ACTION=add
monitor:DEVPATH=/module/hst_tx99
monitor:SUBSYSTEM=module
monitor:SEQNUM=644
monitor:event { 'add', '' }
iptables: Bad rule (does a matching rule exist in that chain?).
qrcode_text = WIFI:T:WPA;S:T-Mobile-ZTE MF286-A8FF92;P:misiulka2160;
iptables: Bad rule (does a matching rule exist in that chain?).
iptables: Bad rule (does a matching rule exist in that chain?).
insmod: can't insert '/lib/modules/3.3.8/shortcut-fe.ko': File exists
insmod: can't insert '/lib/modules/3.3.8/shortcut-fe-ipv6.ko': File exists
insmod: can't insert '/lib/modules/3.3.8/shortcut-fe-cm.ko': File exists
qrcode_text = WIFI:T:WPA;S:T-Mobile-ZTE MF286-A8FF92;P:misiulka2160;
/sbin/firewall_setting_level.sh: no dev in, set usb0!
/sbin/firewall_setting_level.sh: no firewall_level spi, exit 0
/sbin/firewall_setting_level.sh: no dev in, set usb0!
/sbin/firewall_setting_level.sh: no firewall_level spi, exit 0
/sbin/firewall_setting_level.sh: no dev in, set usb0!
/sbin/firewall_setting_level.sh: no firewall_level spi, exit 0
tr069 func is not support, return!
[ 59.710000] ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved
monitor:add@/module/ath_dev
monitor:ACTION=add
monitor:DEVPATH=/module/ath_dev
monitor:SUBSYSTEM=module
monitor:SEQNUM=645
monitor:event { 'add', '' }
[ 60.120000] __ath_attach: Set global_scn[0]
[ 60.120000] *** All the minfree values should be <= ATH_TXBUF-32, otherwise default value will be used instead ***
[ 60.130000] ACBKMinfree = 48
[ 60.140000] ACBEMinfree = 32
[ 60.140000] ACVIMinfree = 16
[ 60.140000] ACVOMinfree = 0
[ 60.150000] CABMinfree = 48
[ 60.150000] UAPSDMinfree = 0
[ 60.150000] ATH_TXBUF=1500
[ 60.160000] Enterprise mode: 0x03bda000
[ 60.170000] Restoring Cal data from FS
[ 60.170000]
[ 60.170000] ART Version : -48.0.0
[ 60.180000] SW Image Version : -48.0.0.0.0
[ 60.180000] Board Revision :
[ 60.180000] ar9300_attach: nf_2_nom -110 nf_2_max -60 nf_2_min -125
[ 60.190000] Green-AP : Green-AP : Attached
[ 60.190000]
monitor:add@/module/qca_da
moni[ 60.210000] ath_get_caps[6167] rx chainmask mismatch actual 7 sc_chainmak 0
tor:ACTION=add
[ 60.210000] ath_get_caps[6142] tx chainmask mismatch actual 7 sc_chainmak 0
monitor:DEVPATH=/module/qca_da
[ 60.230000] band steering initialized for direct attach hardware
monitor:SUBSYSTE[ 60.230000] ieee80211_bsteering_attach: Band steering initialized
M=module
monito[ 60.240000] ath_attach_dfs[12601] dfsdomain 1
r:SEQNUM=646
monitor:event { 'a[ 60.250000] dfs_attach: event log enabled by default
dd', '' }
[ 60.260000] ath_attach: Set global_ic[1]..gloabl_ic ptr:84912354
[ 60.270000] osif_wrap_attach:441 osif wrap attached
[ 60.280000] osif_wrap_devt_init:402 osif wrap dev table init done
[ 60.280000] Wrap Attached: Wrap_com =85928800 ic->ic_wrap_com=85928800 &wrap_com->wc_devt=85928800
[ 60.300000] ath_tx_paprd_init sc 849e8000 PAPRD disabled in HAL
monitor:add@/devices/virtual/net[ 60.310000] wifi0: Atheros 956X: mem=0xb8100000, irq=47
/wifi0
monitor:[ 60.310000] ath_da_pci: (Atheros/multi-bss)
ACTION=add
monitor:DEVPATH=/devices/virtual/net/wifi0
monitor:SUBSYSTEM=net
monitor:INTERFACE=wifi0
monitor:IFINDEX=10
monitor:SEQNUM=647
monitor:event { 'add', '' }
monitor:add@/devices/virtual/net/wifi0/queues/tx-0
monitor:ACTION=add
monitor:DEVPATH=/devices/virtual/net/wifi0/queues/tx-0
monitor:SUBSYSTEM=queues
monitor:SEQNUM=648
monitor:event { 'add', '' }
monitor:add@/bus/platform/drivers/ath9k_ahb
monitor:ACTION=add
monitor:DEVPATH=/bus/platform/drivers/ath9k_ahb
monitor:SUBSYSTEM=drivers
monitor:SEQNUM=649
monitor:event { 'add', '' }
monitor:add@/bus/pci/drivers/ath_da_pci
monitor:ACTION=add
monitor:DEVPATH=/bus/pci/drivers/ath_da_pci
monitor:SUBSYSTEM=drivers
monitor:SEQNUM=650
monitor:event { 'add', '' }
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
ip6tables: No chain/target/match by that name.
ip6tables: No chain/target/match by that name.
ip6tables: No chain/target/match by that name.
ip6tables: No chain/target/match by that name.
ip6tables: No chain/target/match by that name.
ip6tables: No chain/target/match by that name.
insmod: can't insert '/lib/modules/3.3.8/shortcut-fe.ko': File exists
insmod: can't insert '/lib/modules/3.3.8/shortcut-fe-ipv6.ko': File exists
insmod: can't insert '/lib/modules/3.3.8/shortcut-fe-cm.ko': File exists
qrcode_text = WIFI:T:WPA;S:T-Mobile-ZTE MF286-A8FF92_2;P:22368003;
monitor:add@/module/qca_ol
monitor:ACTION=add
[ 62.700000] ath_ol_pci: (Atheros/multi-bss)
monitor:DEVPATH=[ 62.700000] hif_pci_enable_bus: con_mode = 0x0, device_id = 0x56/module/qca_ol
[ 62.710000] ath_ol_pci 0000:00:00.0: BAR 0: assigned [mem 0x12000000-0x121fffff 64bit]
monitor:SUBSYSTE[ 62.720000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
M=module
monito[ 62.730000] hif_pci_enable_bus: hif_enable_pci doner:SEQNUM=651
mo *********** QCA9888 *************nitor:event { 'ahif_pci_enable_bus: hif_type = 0xe, target_type = 0xcdd', '' }
monithif_pci_enable_bus: hif_pci_probe_tgt_wakeup doneor:add@/bus/plathif_target_sync: Loop checking FW signalform/drivers/athhif_target_sync: Got FW signal, retries = 010k_ahb
monitorhif_config_ce: ce_init done:ACTION=add
monhif_config_ce: X, ret = 0itor:DEVPATH=/buhif_set_hia: Es/platform/drivers/ath10k_ahb
monitor:SUBSYSTEM=drivers
monitor:SEQNUM=652
monitor:event { 'add', '' }
hif_set_hia_extnd: E
[ 62.780000] chip_id 0xc chip_revision 0x0
[ 62.790000]
[ 62.790000] CLOCK PLL skipped
[ 62.790000] hif_set_hia_extnd: setting the target pll frac ffffffff intval ffffffff
[ 62.800000] hif_set_hia_extnd: no frac provided, skipping pre-configuring PLL
[ 62.810000] hif_pci_bus_configure: hif_set_hia donehif_configure_irq: Ehif_pci_configure_legacy_irq: Ehif_pci_configure_legacy_irq: X, ret = 0hif_enable: X OKhif_napi_create: NAPI structures initializedhif_napi_create: NAPI id 6 created for pipe 5qca_napi_create: napi instance 32 created on pipe 4
[ 62.840000] hif_napi_event: received evnt: CONF cmd; v = 1 (state=0x1)hif_napi_event: setting configuration to ON
[ 62.850000] __ol_ath_attach() Allocated scn 84b80380
[ 62.850000] __ol_ath_attach: dev name wifi1
[ 62.860000] ol_ath_attach interface_id 1
[ 62.860000] ol_target_init() BMI inited.
[ 62.880000] ol_target_init() BMI Get Target Info.
[ 62.880000] Chip id: 0xc, chip version: 0x1000000
[ 62.890000]
[ 62.890000] CE WAR Disabled
[ 62.890000] NUM_DEV=1 FWMODE=0x2 FWSUBMODE=0x0 FWBR_BUF 0
[ 62.920000] ol_target_init() configure Target .
[ 62.920000]
[ 62.920000] Target Version is 1000000
[ 62.930000]
[ 62.930000] Flash Download Address c0000
[ 62.930000] ol_transfer_bin_file: flash data file defined
[ 62.940000] ol_transfer_bin_file[3637] Get Caldata for wifi1.
[ 62.940000] qdf_fs_read[59], Open File /tmp/wifi1.caldata SUCCESS!!file system magic:16914836super blocksize:4096inode 6921file size:12064qc98xx_verify_checksum: flash checksum passed: 0xfd26
[ 62.970000] ol_transfer_bin_file 3698: Download Flash data len 12064
[ 62.980000] Board extended Data download address: 0x0
[ 63.070000]
[ 63.070000] Board data initialized
[ 63.130000] ol_ath_download_firmware: Download OTP, flash download ADDRESS 0xc0000
[ 63.130000]
[ 63.130000] Selecting OTP binary for CHIP Version 0
qrcode_text = WIFI:T:WPA;S:T-Mobile-ZTE MF286-A8FF92_2;P:22368003;
speed limit is disabled, so we need to enable SFE,clear iptable and tc rules
insmod: can't insert '/lib/modules/3.3.8/shortcut-fe-cm.ko': File exists
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
monitor:add@/devices/pci0000:00/0000:00:00.0/firmware/0000:00:00.0
monitor:ACTION=add
monitor:DEVPATH=/devices/pci0000:00/0000:00:00.0/firmware/0000:00:00.0
monitor:SUBSYSTEM=firmware
monitor:FIRMWARE=QCA9888/hw.2/otp.bin
monitor:TIMEOUT=60
monitor:ASYNC=0
monitor:SEQNUM=653
monitor:event { 'add', '' }
Reading chip2_ssid1_qr .
Reading chip2_ssid1_qr o
Read OK chip2_ssid1_qr
Reading chip1_ssid1_qr .
Reading chip1_ssid1_qr o
Read OK chip1_ssid1_qr [ 64.100000] ol_transfer_bin_file 3518: downloading file 0, Download data len 9084
monitor:remove@/devices/pci0000:00/0000:00:00.0/firmware/0000:00:00.0
monitor:ACTION=remove
monitor:DEVPATH=/devices/pci0000:00/0000:00:00.0/firmware/0000:00:00.0
monitor:SUBSYSTEM=firmware
monitor:FIRMWARE=QCA9888/hw.2/otp.bin
monitor:TIMEOUT=60
monitor:ASYNC=0
monitor:SEQNUM=654
monitor:event { 'remove', '' }
RTNETLINK answers: Invalid argument
Reading chip2_ssid2_qr .
Reading chip2_ssid2_qr o
Read OK chip2_ssid2_qr RTNETLINK answers: Invalid argument
[ 64.180000]
[ 64.180000] First OTP send param 8000
Writing chip2_ssid1_qr
OK chip2_ssid1_qr
Writing chip1_ssid1_qr
OK chip1_ssid1_qr
Writing chip2_ssid2_qr
OK chip2_ssid2_qr
Reading chip1_ssid2_qr .
Reading chip1_ssid2_qr o
Read OK chip1_ssid2_qr
Writing chip1_ssid2_qr
OK chip1_ssid2_qr
[ 64.430000] ol_ath_download_firmware :First OTP download and Execute is good address:0x4000 return param 4660
[ 64.440000] ol_ath_download_firmware:##Board Id 16 , CHIP Id 0
[ 64.450000] ol_ath_download_firmware: BOARDDATA DOWNLOAD TO address 0xc0000
[ 64.450000]
[ 64.450000] wifi1: Selecting board data file name boardData_2_0_QCA9888_5G_Y9690.bin
[ 64.460000] ol_transfer_bin_file: Board Data File download to address=0xc0000 file name=QCA9888/hw.2/boardData_2_0_QCA9888_5G_Y9690.bin
monitor:add@/devices/pci0000:00/0000:00:00.0/firmware/0000:00:00.0
monitor:ACTION=add
monitor:DEVPATH=/devices/pci0000:00/0000:00:00.0/firmware/0000:00:00.0
monitor:SUBSYSTEM=firmware
monitor:FIRMWARE=QCA[ 64.490000] ol_transfer_bin_file 3518: downloading file 3, Download data len 12064
9888/hw.2/boardD[ 64.500000] Board extended Data download address: 0x0
ata_2_0_QCA9888_5G_Y9690.bin
monitor:TIMEOUT=60
monitor:ASYNC=0
monitor:SEQNUM=655
monitor:event { 'add', '' }
/sbin/second_ssid_access_control.shmonitor:remove@/devices/pci0000:00/0000:00:00.0/firmware/0000:00:00.0
monitor:ACTION=remove
monitor:DEVPATH=/devices/pci0000:00/0000:00:00.0/firmware/0000:00:00.0
monitor:SUBSYSTEM=firmware
monitor:FIRMWARE=QCA9888/hw.2/boardData_2_0_QCA9888_5G_Y9690.bin
monitor:TIMEOUT=60
monitor:ASYNC=0
monitor:SEQNUM=656
monitor:event { 'remove', '' }
: line 17: ebtables: not found
/sbin/second_ssid_access_control.sh: line 18: ebtables: not found
/sbin/sec[ 64.560000] ol_ath_download_firmware: Using 0x1234 for the remainder of init
ond_ssid_access_[ 64.570000]
[ 64.570000] Selecting OTP binary for CHIP Version 0
control.sh: line 19: ebtables: not found
/sbin/second_ssid_access_control.sh: line 20: ebtables: not found
/sbin/second_ssid_access_control.sh: line 21: ebtables: not found
lan_sec_ssid_control [] allow webUI
monitor:add@/devices/pci0000:00/0000:00:00.0/firmware/0000:00:00.0
monitor:ACTION=add
monitor:DEVPATH=/devices/pci0000:00/0000:00:00.0/firmware/0000:00:00.0
monitor:SUBSYSTEM=firmware
monitor:FIRMWARE=QCA9888/hw.2/otp.bin
monitor:TIMEOUT=60
monitor:ASYNC=0
monitor:SEQNUM=657
monitor:event {[ 64.620000] ol_transfer_bin_file 3518: downloading file 0, Download data len 9084
'add', '' }
monitor:remove@/devices/pci0000:00/0000:00:00.0/firmware/0000:00:00.0
monitor:ACTION=remove
monitor:DEVPATH=/devices/pci0000:00/0000:00:00.0/firmware/0000:00:00.0
monitor:SUBSYSTEM=firmware
monitor:FIRMWARE=QCA9888/hw.2/otp.bin
monitor:TIMEOUT=60
monitor:ASYNC=0
monitor:SEQNUM=658
monitor:event { 'remove', '' }
[ 64.680000]
[ 64.680000] [Flash] : Ignore Module param
[ 64.690000]
[ 64.690000] Second otp download Param 10000
[ 64.940000] ol_ath_download_firmware : Second OTP download and Execute is good, param=0x0
[ 64.950000]
[ 64.950000] Mission mode: Firmware CHIP Version 0
monitor:add@/devices/pci0000:00/0000:00:00.0/firmware/0000:00:00.0
monitor:ACTION=add
monitor:DEVPATH=/devices/pci0000:00/0000:00:00.0/firmware/0000:00:00.0
monitor:SUBSYSTEM=firmware
monitor:FIRMWARE=QCA9888/hw.2/athwlan.codeswap.bin
monitor:TIMEOUT=60
monitor:ASYNC=0
monitor:SEQNUM=659
monitor:event { 'add', '' }
[ 65.640000] ol_swap_seg_alloc: Successfully allocated memory for SWAP size=262144
monitor:remove@/devices/pci0000:00/0000:00:00.0/firmware/0000:00:00.0
monitor:ACTION=remove
monitor:DEVPATH=/devices/pci0000:00/0000:00:00.0/firmware/0000:00:00.0
monitor:SUBSYSTEM=firmware
monitor:FIRMWARE=QCA9888/hw.2/athwlan.codeswap[ 65.670000] Swap: bytes_left to copy: fw:16; dma_page:28605
.bin
monitor:TI[ 65.680000] Swap: wrong length read:0
MEOUT=60
monito[ 65.690000] ol_swap_wlan_memory_expansion: Swap total_bytes copied: 233539 Target address 41a4a8
r:ASYNC=0
monitor:SEQNUM=660
monitor:event { 'remove', '' }
m[ 65.700000] scn=84b80380 target_write_addr=41a4a8 seg_info=84be2010
onitor:add@/devi[ 65.710000] ol_transfer_swap_struct:Code swap structure successfully downloaded for bin type =2
ces/pci0000:00/0[ 65.720000] bin_filename=QCA9888/hw.2/athwlan.bin swap_filename=/lib/firmware/QCA9888/hw.2/athwlan.codeswap.bin
000:00:00.0/firm[ 65.730000] ol_transfer_bin_file: Downloading firmware file: QCA9888/hw.2/athwlan.bin
ware/0000:00:00.0
monitor:ACTION=add
monitor:DEVPATH=/devices/pci0000:00/0000:00:00.0/firmware/0000:00:00.0
monitor:SUBSYSTEM=firmware
monitor:FIRMWARE=QCA9888/hw.2/athwlan.codeswap.bin
monitor:TIMEOUT=60
monitor:ASYNC=0
monitor:SEQNUM=661
monitor:event { 'add', '' }
monitor:remove@/devices/pci0000:00/0000:00:00.0/firmware/0000:00:00.0
monitor:ACTION=remove
monitor:DEVPATH=/devices/pci0000:00/0000:00:00.0/firmware/0000:00:00.0
monitor:SUBSYSTEM=firmware
monitor:FIRMWARE=QCA9888/hw.2/athwlan.codeswap.bin
monitor:TIMEOUT=60
monitor:ASYNC=0
monitor:SEQNUM=662
monitor:event { 'remove', '' }
monitor:add@/devices/pci0000:00/0000:00:00.0/firmware/0000:00:00.0
monitor:ACTION=add
monitor:DEVPATH=/devices/pci0000:00/0000:00:00.0/firmware/0000:00:00.0
monitor:SUBSYSTEM=firmware
monitor:FIRMWARE=QCA9888/hw.2/athwlan.bin
monitor:TIMEOUT=60
monitor:ASYNC=0
monitor:SEQNUM=663
monitor:event { 'add', '' }
[ 67.370000] ol_transfer_bin_file 3518: downloading file 1, Download data len 372428
monitor:remove@/devices/pci0000:00/0000:00:00.0/firmware/0000:00:00.0
monitor:ACTION=remove
monitor:DEVPATH=/devices/pci0000:00/0000:00:00.0/firmware/0000:00:00.0
monitor:SUBSYSTEM=firmware
monitor:FIRMWARE=QCA9888/hw.2/athwlan.bin
monitor:TIMEOUT=60
monitor:ASYNC=0
monitor:SEQNUM=664
monitor:event { 'remove', '' }
3 KB/s (154 bytes in 0.043s)
[ 68.840000] ol_target_init() Download FW done.
[ 68.840000] ol_ath_attach() WMI attached. wmi_handle 8725a000
[ 68.850000] wmi_unified_register_event_handler: Event id 62 is unavailable
[ 68.860000] +htc_create .. HIF :84b04000-htc_create: (0x8580d800)
[ 68.860000] htc_wmi_init() HT Create . 8580d800
[ 68.870000] htc_wmi_init 7528 host_enable 0 nss_nwifi_offload 0
[ 68.870000] ol_ath_set_default_tgt_config : AC Minfree buffer allocation through module param (umac.ko)
[ 68.880000] OL_ACBKMinfree : 0
[ 68.890000] OL_ACBEMinfree : 0
[ 68.890000] OL_ACVIMinfree : 0
[ 68.890000] OL_ACVOMinfree : 0
[ 68.900000] hif_enable_fastpath, Enabling fastpath mode
[ 68.900000] +HWT
[ 68.900000] hif_completion_thread_startup: pipe_num:0 pipe_info:0x84b0705chif_completion_thread_startup: pipe_num:3 pipe_info:0x84b0711chif_completion_thread_startup: pipe_num:4 pipe_info:0x84b0715c
[ 68.920000] -HWT
[ 68.930000] Startup Mode-0 set
[ 68.930000]
[ 68.930000] <=== cfg max peer id 288 ====>
[ 68.940000] htt_peer_map_timer_init Enter pdev 840fc000 hrtimer 840fc948
[ 68.950000]
[ 68.950000] htt_alloc_peer_map_mem : Alloc Success : host q vaddr 8407cc00 paddr 407cc00
[ 68.960000]
[ 68.960000] htt_alloc_peer_map_mem : Flush Interval Configured to 256 pkts
[ 68.970000] ol_txrx_pdev_attach: 2500 tx desc's allocated ; range starts from 83c60000
[ 68.990000] Firmware_Build_Number:61
[ 68.990000] FW wireless modes: 0x7f9001
[ 68.990000] num_rf_chain:0x00000002 ht_cap_info:0x0000085b vht_cap_info:0x339979fa vht_supp_mcs:0x0000fffa
[ 69.000000] wmi_service_coex_gpio 0, wmi_service_4_wire_coex_support 0, coex_version 0
[ 69.010000]
[ 69.010000] Sending Ext resource cfg: HOST PLATFORM as 1
[ 69.010000] fw_feature_bitmap as 50 to TGT
[ 69.020000] ol_ath_service_ready_event: tt_support: 1
[ 69.030000] ol_ath_service_ready_event: periodic_chan_stats: 1
[ 69.030000] ol_ath_service_ready_event: sw_cal_support_check_flag: 1
[ 69.040000] Peer Caching Enabled ; num_peers = 38, num_active_peers = 25 num_tids = 50, num_vdevs = 5
[ 69.050000] idx 1 req 2 num_units 1 num_unit_info 12 unit size 256 actual units 26
[ 69.060000] ol_ath_alloc_host_mem_chunk req_id 2 idx 0 num_units 26 unit_len 256,
[ 69.070000] idx 2 req 3 num_units 1 num_unit_info 12 unit size 1024 actual units 26
[ 69.070000] ol_ath_alloc_host_mem_chunk req_id 3 idx 1 num_units 26 unit_len 1024,
[ 69.080000] idx 3 req 4 num_units 1 num_unit_info 12 unit size 4096 actual units 26
[ 69.090000] ol_ath_alloc_host_mem_chunk req_id 4 idx 2 num_units 26 unit_len 4096,
[ 69.100000] idx 0 req 1 num_units 0 num_unit_info 2 unit size 896 actual units 39
[ 69.110000] ol_ath_alloc_host_mem_chunk req_id 1 idx 3 num_units 39 unit_len 896,
[ 69.110000] idx 4 req 5 num_units 0 num_unit_info 2 unit size 1948 actual units 39
[ 69.120000] ol_ath_alloc_host_mem_chunk req_id 5 idx 4 num_units 39 unit_len 1948,
[ 69.130000] Support not added yet for Service 91
[ 69.140000] Support not added yet for Service 92
[ 69.140000] No EXT_MSG send INIT now
[ 69.140000] chunk 0 len 6656 requested , ptr 0x407e000
[ 69.150000] chunk 1 len 26624 requested , ptr 0x3c50000
[ 69.150000] chunk 2 len 106496 requested , ptr 0x3cc0000
[ 69.160000] chunk 3 len 34944 requested , ptr 0x3ce0000
[ 69.170000] chunk 4 len 75972 requested , ptr 0x3d00000
[ 69.170000] ol_ath_service_ready_event[4259] WAPI MBSSID 2
[ 69.210000] Version = 16777216 3 status = 0
[ 69.220000] ol_ath_connect_htc() WMI is ready
[ 69.220000] htt_h2t_frag_desc_bank_cfg_msg - HTT_H2T_MSG_TYPE_FRAG_DESC_BANK_CFG sent to FW for radio ID = 1
[ 69.230000] target uses HTT version 2.2; host uses 2.2
[ 69.240000] ol_ath_attach() connect HTC.
[ 69.250000] bypasswmi : 0
[ 69.250000] ol_regdmn_start: reg-domain param: regdmn=0, countryName=, wModeSelect=FFFFFFFF, netBand=FFFFFFFF, extendedChanMode=0.
[ 69.260000] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x2) flags 0x2150
[ 69.270000] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x4) flags 0xa0
[ 69.280000] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x8) flags 0xc0
[ 69.280000] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x20) flags 0xd0
[ 69.290000] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x40) flags 0x150
[ 69.300000] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x800) flags 0x10080
[ 69.310000] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x2000) flags 0x20080
[ 69.310000] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x4000) flags 0x40080
[ 69.320000] Add VHT80 channel: 5210
[ 69.330000] Add VHT80 channel: 5290
[ 69.330000] Add VHT80 channel: 5530
[ 69.330000] Add VHT80 channel: 5610
[ 69.340000] Add VHT80 channel: 5690
[ 69.340000] Add VHT80 channel: 5775
[ 69.340000] Skipping VHT80 channel 5825
[ 69.350000] EMI WAR rejecting fc1 > fc2 Combination cfreq1:5530, cfreq2:5210 in case of VHT80+80
[ 69.360000] EMI WAR rejecting fc1 > fc2 Combination cfreq1:5530, cfreq2:5290 in case of VHT80+80
[ 69.370000] EMI WAR rejecting fc1 > fc2 Combination cfreq1:5530, cfreq2:5210 in case of VHT80+80
[ 69.380000] EMI WAR rejecting fc1 > fc2 Combination cfreq1:5530, cfreq2:5290 in case of VHT80+80
[ 69.380000] EMI WAR rejecting fc1 > fc2 Combination cfreq1:5530, cfreq2:5210 in case of VHT80+80
[ 69.390000] EMI WAR rejecting fc1 > fc2 Combination cfreq1:5530, cfreq2:5290 in case of VHT80+80
[ 69.400000] EMI WAR rejecting fc1 > fc2 Combination cfreq1:5530, cfreq2:5210 in case of VHT80+80
[ 69.410000] EMI WAR rejecting fc1 > fc2 Combination cfreq1:5530, cfreq2:5290 in case of VHT80+80
[ 69.420000] EMI WAR rejecting fc1 > fc2 Combination cfreq1:5610, cfreq2:5210 in case of VHT80+80
[ 69.430000] EMI WAR rejecting fc1 > fc2 Combination cfreq1:5610, cfreq2:5290 in case of VHT80+80
[ 69.440000] EMI WAR rejecting fc1 > fc2 Combination cfreq1:5610, cfreq2:5210 in case of VHT80+80
[ 69.450000] EMI WAR rejecting fc1 > fc2 Combination cfreq1:5610, cfreq2:5290 in case of VHT80+80
[ 69.460000] EMI WAR rejecting fc1 > fc2 Combination cfreq1:5610, cfreq2:5210 in case of VHT80+80
[ 69.470000] EMI WAR rejecting fc1 > fc2 Combination cfreq1:5610, cfreq2:5290 in case of VHT80+80
[ 69.480000] EMI WAR rejecting fc1 > fc2 Combination cfreq1:5610, cfreq2:5210 in case of VHT80+80
[ 69.480000] EMI WAR rejecting fc1 > fc2 Combination cfreq1:5610, cfreq2:5290 in case of VHT80+80
[ 69.490000] EMI WAR rejecting fc1 > fc2 Combination cfreq1:5690, cfreq2:5210 in case of VHT80+80
[ 69.500000] EMI WAR rejecting fc1 > fc2 Combination cfreq1:5690, cfreq2:5290 in case of VHT80+80
[ 69.510000] EMI WAR rejecting fc1 > fc2 Combination cfreq1:5690, cfreq2:5530 in case of VHT80+80
[ 69.520000] EMI WAR rejecting fc1 > fc2 Combination cfreq1:5690, cfreq2:5210 in case of VHT80+80
[ 69.530000] EMI WAR rejecting fc1 > fc2 Combination cfreq1:5690, cfreq2:5290 in case of VHT80+80
[ 69.540000] EMI WAR rejecting fc1 > fc2 Combination cfreq1:5690, cfreq2:5530 in case of VHT80+80
[ 69.550000] EMI WAR rejecting fc1 > fc2 Combination cfreq1:5775, cfreq2:5210 in case of VHT80+80
[ 69.560000] EMI WAR rejecting fc1 > fc2 Combination cfreq1:5775, cfreq2:5290 in case of VHT80+80
[ 69.570000] EMI WAR rejecting fc1 > fc2 Combination cfreq1:5775, cfreq2:5530 in case of VHT80+80
[ 69.580000] EMI WAR rejecting fc1 > fc2 Combination cfreq1:5775, cfreq2:5610 in case of VHT80+80
[ 69.580000] EMI WAR rejecting fc1 > fc2 Combination cfreq1:5775, cfreq2:5690 in case of VHT80+80
[ 69.590000] EMI WAR rejecting fc1 > fc2 Combination cfreq1:5775, cfreq2:5210 in case of VHT80+80
[ 69.600000] EMI WAR rejecting fc1 > fc2 Combination cfreq1:5775, cfreq2:5290 in case of VHT80+80
[ 69.610000] EMI WAR rejecting fc1 > fc2 Combination cfreq1:5775, cfreq2:5530 in case of VHT80+80
[ 69.620000] EMI WAR rejecting fc1 > fc2 Combination cfreq1:5775, cfreq2:5610 in case of VHT80+80
[ 69.630000] EMI WAR rejecting fc1 > fc2 Combination cfreq1:5775, cfreq2:5690 in case of VHT80+80
[ 69.640000] EMI WAR rejecting fc1 > fc2 Combination cfreq1:5775, cfreq2:5210 in case of VHT80+80
[ 69.650000] EMI WAR rejecting fc1 > fc2 Combination cfreq1:5775, cfreq2:5290 in case of VHT80+80
[ 69.660000] EMI WAR rejecting fc1 > fc2 Combination cfreq1:5775, cfreq2:5530 in case of VHT80+80
[ 69.670000] EMI WAR rejecting fc1 > fc2 Combination cfreq1:5775, cfreq2:5610 in case of VHT80+80
[ 69.680000] EMI WAR rejecting fc1 > fc2 Combination cfreq1:5775, cfreq2:5690 in case of VHT80+80
[ 69.680000] EMI WAR rejecting fc1 > fc2 Combination cfreq1:5775, cfreq2:5210 in case of VHT80+80
[ 69.690000] EMI WAR rejecting fc1 > fc2 Combination cfreq1:5775, cfreq2:5290 in case of VHT80+80
[ 69.700000] EMI WAR rejecting fc1 > fc2 Combination cfreq1:5775, cfreq2:5530 in case of VHT80+80
[ 69.710000] EMI WAR rejecting fc1 > fc2 Combination cfreq1:5775, cfreq2:5610 in case of VHT80+80
[ 69.720000] EMI WAR rejecting fc1 > fc2 Combination cfreq1:5775, cfreq2:5690 in case of VHT80+80
[ 69.730000] freq=58
[ 69.730000] freq=106
[ 69.740000] freq=122
[ 69.740000] freq=138
[ 69.740000] OL Resmgr Init-ed
[ 69.750000] ieee80211_bsteering_attach: Band steering initialized
[ 69.750000] Green-AP : Green-AP : Attached
[ 69.750000]
[ 69.760000] Green-AP : Attached
[ 69.760000] rate power table override is only supported for AR98XX
[ 69.770000] ol_if_dfs_attach: called; ptr=83cf197c, radar_info=85ad5b58
[ 69.770000] dfs_attach: event log enabled by default
[ 69.780000] >>>> CB Set (null)
[ 69.780000] __init_external_data_flow_report() enter
[ 69.790000] ol_ath_attach() UMAC attach .
[ 69.790000]
[ 69.790000] BURSTING enabled by default
[ 69.800000] ol_ath_attach: Set global_ic[2] ..ptr:84912354
[ 69.810000] osif_wrap_attach:441 osif wrap attached
[ 69.810000] osif_wrap_devt_init:402 osif wrap dev table init done
[ 69.820000] Wrap Attached: Wrap_com =8585e800 ic->ic_wrap_com=8585e800 &wrap_com->wc_devt=8585e800
[ 69.830000] __ol_ath_attach: needed_headroom reservation 60
monitor:add@/devices/pci0000:00/0000:00:00.0/net/wifi1
monitor:ACTION=add
monitor:DEVPATH=/devices/pci0000:00/0000:00:00.0/net/wifi1
monitor:SUBSYSTEM=net
monitor:INTERFACE=wifi1
monitor:IFINDEX=11
monitor:SEQNUM=665
monitor:event { 'add', '' }
monitor:add@/devices/pci0000:00/0000:00:00.0/net/wifi1/queues/tx-0
[ 69.870000] ol_ath_thermal_mitigation_attach: --
monitor:ACTION=[ 69.880000] ol_ath_pci_probe num_radios=0, wifi_radios[0].sc = 84b80380 wifi_radio_type = 2
add
monitor:DEV[ 69.890000] ath_sysfs_diag_init: diag_fsattr
PATH=/devices/pci0000:00/0000:00[ 69.890000] [wifi1] :00.0/net/wifi1/FWLOG: [76829] WAL_DBGID_TX_AC_BUFFER_SET ( queues/tx-0
mon0x3itor:SUBSYSTEM=q, ueues
monitor:S0x1eEQNUM=666
monit, or:event { 'add'0x94c, '' }
monitor:, add@/bus/pci/dri0x94cvers/ath_ol_pci
,
monitor:ACTION=0x0add
monitor:DEV )
PATH=/bus/pci/dr[ 69.920000] [wifi1] ivers/ath_ol_pciFWLOG: [76829] WAL_DBGID_TX_AC_BUFFER_SET (
monitor:SUBSYS0x12TEM=drivers
mon, itor:SEQNUM=667
0x1e
monitor:event {, 'add', '' }
0x94c, 0x94c, 0x0 )
[ 69.940000] [wifi1] FWLOG: [76829] WAL_DBGID_TX_AC_BUFFER_SET ( 0x45, 0x1e, 0x94c, 0x94c, 0x0 )
[ 69.950000] [wifi1] FWLOG: [76829] WAL_DBGID_TX_AC_BUFFER_SET ( 0x67, 0x1e, 0x94c, 0x94c, 0x0 )
[ 69.960000] [wifi1] FWLOG: [76829] WAL_DBGID_TX_AC_BUFFER_SET ( 0x100, 0x11e1a300 )
[ 69.970000] [wifi1] FWLOG: [77360] UNKNOWN 22:55 ( 0x3a, 0xa10, 0x160, 0x10, 0x0 )
[ 70.080000] pktlog_init: Initializing Pktlog for AR900B, pktlog_hdr_size = 16
[ 70.080000] +hif_update_pipe_callback pipeid 8
[ 70.090000] -hif_update_pipe_callback
monitor:add@/module/ath_pktlog
monitor:ACTION=add
monitor:DEVPATH=/module/ath_pktlog
monitor:SUBSYSTEM=module
monitor:SEQNUM=668
monitor:event { 'add', '' }
Invalid command : txbf_snd_int
[ 70.210000] set TXBF_SND_PERIOD: value 100 wmi_status 0
Invalid command : obss_rx_rssi_th
add light on here if need
[ 70.810000] wlan_vap_create : enter. devhandle=0x849f0380, opmode=IEEE80211_M_HOSTAP, flags=0x100
[ 70.820000] ieee80211_mbo_vattach:MBO Initialized
[ 70.820000] ieee80211_oce_vattach: OCE Initialized
[ 70.830000] wlan_vap_create : exit. devhandle=0x849f0380, vap=0x84048000, opmode=IEEE80211_M_HOSTAP, flags=0x100.
[ 70.840000] VAP device ath00 created osifp: (83dd4b80) os_if: (84048000)
monitor:add@/devices/virtual/net/ath00
monitor:ACTION=add
monitor:DEVPATH=/devices/virtual/net/ath00
monitor:SUBSYSTEM=net
monitor:INTERFACE=ath00
monitor:IFINDEX=12
monitor:SEQNUM=669
monitor:event { 'add', '' }
monitor:add@/devices/virtual/net/ath00/queues/tx-0
monitor:ACTION=add
monitor:DEVPATH=/devices/virtual/net/ath00/queues/tx-0
monitor:SUBSYSTEM=queues
monitor:SEQNUM=670
monitor:event { 'add', '' }
Interface doesn't accept private ioctl...
stafwd (8BE0): Invalid argument
unzip: can't open /etc_rw/fota/image.zip, /etc_rw/fota/image.zip.zip, /etc_rw/fota/image.zip.ZIP
cannot stat '/tmp/delta.package': No such file or directory
00:00:26 UP>>[up[ 71.040000] device ath00 entered promiscuous mode
date_control.c:3012]start zte_dm
addd ath00 to br0
[ 71.130000] wlan_vap_create : enter. devhandle=0x84b80380, opmode=IEEE80211_M_HOSTAP, flags=0x100
[ 71.130000] send_vdev_create_cmd_non_tlv: ID = 0 Type = 1, Subtype = 0 VAP Addr = c8:ea:f8:aa:ff:92:
[ 71.140000] ieee80211_mbo_vattach:MBO Initialized
[ 71.150000] ieee80211_oce_vattach: OCE Initialized
[ 71.150000] wlan_vap_create : exit. devhandle=0x84b80380, vap=0x83e10000, opmode=IEEE80211_M_HOSTAP, flags=0x100.
[ 71.170000] Enabling TX checksum bit for the vap ath12 features 4000
[ 71.170000] Enabling SG bit for the vap ath12 features 4000
[ 71.180000] Enabling SG bit for the vap ath12 features 4000
[ 71.180000] Enabling TSO bit for the vap ath12 features 4000
[ 71.190000] Enabling LRO bit for the vap ath12 features 4000
[ 71.200000] VAP device ath12 created osifp: (83e08380) os_if: (83e10000)
monitor:add@/devices/virtual/net/ath12
monitor:ACTION=add
monitor:DEVPATH=/devices/virtual/net/ath12
monitor:SUBSYSTEM=net
monitor:INTERFACE=ath12
monitor:IFINDEX=13
monitor:SEQNUM=671
monitor:event { 'add', '' }
monitor:add@/devices/virtual/net/ath12/queues/tx-0
monitor:ACTION=add
monitor:DEVPATH=/devices/virtual/net/ath12/queues/tx-0
monitor:SUBSYSTEM=queues
monitor:SEQNUM=672
monitor:event { 'add', '' }
00:00:26 UP>>[update_control.c:2245]fsm turn from 0 to 0.
Interface doesn't accept private ioctl...
stafwd (8BE0): Invalid argument
[ 71.340000] device ath12 entered promiscuous mode
addd ath12 to br09 2022-02-15 16:30:36 (edytowany przez onken 2022-02-15 16:34:59)
- onken
- Użytkownik
- Nieaktywny
Odp: ZTE MF286R - OpenWrt
Kolejne co się udało - uname -a - nie działa
admin@(none):~# cat /proc/cpuinfo16:27:23 UP>>[update_control.c:1978]s_Modem_AT_Status is 0,have sleeped 65 waiting for AT port ready
system type : Qualcomm Atheros QCA956X rev 0
machine : Qualcomm Atheros AP152 reference board
processor : 0
cpu model : MIPS 74Kc V5.0
BogoMIPS : 385.84
wait instruction : yes
microsecond timers : yes
tlb_entries : 32
extra interrupt vector : yes
hardware watchpoint : yes, count: 4, address/irw mask: [0x0000, 0x0ff8, 0x0ffb, 0x0ff8]
ASEs implemented : mips16 dsp
shadow register sets : 1
kscratch registers : 0
core : 0
VCED exceptions cat /sys/kernel/debug/usb/devices
BusyBox v1.19.4 (2021-05-13 04:17:46 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.
MM NM MMMMMMM M M
$MMMMM MMMMM MMMMMMMMMMM MMM MMM
MMMMMMMM MM MMMMM. MMMMM:MMMMMM: MMMM MMMMM
MMMM= MMMMMM MMM MMMM MMMMM MMMM MMMMMM MMMM MMMMM'
MMMM= MMMMM MMMM MM MMMMM MMMM MMMM MMMMNMMMMM
MMMM= MMMM MMMMM MMMMM MMMM MMMM MMMMMMMM
MMMM= MMMM MMMMMM MMMMM MMMM MMMM MMMMMMMMM
MMMM= MMMM MMMMM, NMMMMMMMM MMMM MMMM MMMMMMMMMMM
MMMM= MMMM MMMMMM MMMMMMMM MMMM MMMM MMMM MMMMMM
MMMM= MMMM MM MMMM MMMM MMMM MMMM MMMM MMMM
MMMM$ ,MMMMM MMMMM MMMM MMM MMMM MMMMM MMMM MMMM
MMMMMMM: MMMMMMM M MMMMMMMMMMMM MMMMMMM MMMMMMM
MMMMMM MMMMN M MMMMMMMMM MMMM MMMM
MMMM M MMMMMMM M M
M
---------------------------------------------------------------
For those about to rock... (QCA9558.LN, unknown)
---------------------------------------------------------------
admin@(none):~# admin@(none):~# cat /sys/kernel/debug/usb/devices
T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 1
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0002 Rev= 3.03
S: Manufacturer=Linux 3.3.8 ehci_hcd
S: Product=Generic Platform EHCI Controller
S: SerialNumber=ehci-platform.1
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 1
B: Alloc= 0/800 us ( 0%), #Int= 2, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0002 Rev= 3.03
S: Manufacturer=Linux 3.3.8 ehci_hcd
S: Product=Generic Platform EHCI Controller
S: SerialNumber=ehci-platform.0
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=19d2 ProdID=1489 Rev=ff.ff
S: Manufacturer=ZTE
S: Product=ZTE
S: SerialNumber=123456789ABCD
C:* #Ifs= 8 Cfg#= 1 Atr=e0 MxPwr= 2mA
A: FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=03
A: FirstIf#= 2 IfCount= 2 Cls=02(comm.) Sub=02 Prot=01
A: FirstIf#= 6 IfCount= 2 Cls=02(comm.) Sub=06 Prot=00
I:* If#= 0 Alt= 0 #EPs= 1 Cls=e0(wlcon) Sub=01 Prot=03 Driver=rndis_host
E: Ad=82(I) Atr=03(Int.) MxPS= 8 Ivl=1ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=rndis_host
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=02 Prot=01 Driver=cdc_acm
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_acm
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=ff Driver=(none)
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=usbfs
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 6 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=00 Driver=cdc_ether
E: Ad=88(I) Atr=03(Int.) MxPS= 16 Ivl=32ms
I: If#= 7 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
I:* If#= 7 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
admin@(none):~#Odp: ZTE MF286R - OpenWrt
Jak uda Ci się przerwać bootloader to weź obraz initramfs i uruchom go w ramie. Nie wgrywaj czasami sysupgrade. Powinien się chyba uruchomić, prawdopodobnie będzie ethernet i wifi. Modem jest faktycznie inny i przypomina mi r11e mikrotikowy, z nim to będzie zabawa bo jeżeli tak jest to on się zachowuje jak ncm ale korzysta z ACMu do inicjacji i RNDISu do komunikacji.
Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.
11 2022-02-15 16:46:58 (edytowany przez onken 2022-02-15 16:48:38)
- onken
- Użytkownik
- Nieaktywny
Odp: ZTE MF286R - OpenWrt
Czyli uruchomić obraz z wersji A ?
Odp: ZTE MF286R - OpenWrt
Tylko w pamięci, tak.
Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.
- onken
- Użytkownik
- Nieaktywny
Odp: ZTE MF286R - OpenWrt
Oki, jak żona wróci z roboty i zajmie się dziećmi to zrobię to
Ale jest do zrobienia by modem zadziałał ?
Jest światełko ?
Odp: ZTE MF286R - OpenWrt
Trzeba tylko znaleźć polecenia inicjujące i tyle. Albo aż tyle, zależy jak na to patrzeć.
Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.
- onken
- Użytkownik
- Nieaktywny
Odp: ZTE MF286R - OpenWrt
To powalczymy służę testami.
Obawiam się że teraz w sprzedaży z nowych pozostał tylko R
- onken
- Użytkownik
- Nieaktywny
Odp: ZTE MF286R - OpenWrt
obraz wstał, co teraz zrobić ?
Odp: ZTE MF286R - OpenWrt
Standardowo - sprawdź sieć, usb, wifi. Modem nie będzie działał. Sprawdź czy wielkość i rozkład partycji zgadza się 286A (tylko pod oryginałem oczywiście). Jeżeli tak to @Leo-PL może zrobić PR od razu też dla 286R. Modem oczywiście nie zadziała.
Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.
- onken
- Użytkownik
- Nieaktywny
Odp: ZTE MF286R - OpenWrt
Ale nie mam LUCI, jak z konsoli posprawdzac ?
root@OpenWrt:/# ifconfig
br-lan Link encap:Ethernet HWaddr C8:EA:F8:A8:FF:92
inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fdd7:d708:2e9a::1/60 Scope:Global
inet6 addr: fe80::caea:f8ff:fea8:ff92/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:1863 errors:0 dropped:0 overruns:0 frame:0
TX packets:18 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:110682 (108.0 KiB) TX bytes:2828 (2.7 KiB)
eth0 Link encap:Ethernet HWaddr C8:EA:F8:A8:FF:92
inet6 addr: fe80::caea:f8ff:fea8:ff92/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:1881 errors:0 dropped:0 overruns:0 frame:0
TX packets:40 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:145623 (142.2 KiB) TX bytes:6966 (6.8 KiB)
Interrupt:4
eth0.1 Link encap:Ethernet HWaddr C8:EA:F8:A8:FF:92
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:1863 errors:0 dropped:0 overruns:0 frame:0
TX packets:18 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:110682 (108.0 KiB) TX bytes:2828 (2.7 KiB)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:712 errors:0 dropped:0 overruns:0 frame:0
TX packets:712 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:54448 (53.1 KiB) TX bytes:54448 (53.1 KiB)
root@OpenWrt:/#Odp: ZTE MF286R - OpenWrt
ifconfig -a jak już. Tak, z konsoli.
Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.
20 2022-02-15 17:47:36 (edytowany przez onken 2022-02-15 17:49:04)
- onken
- Użytkownik
- Nieaktywny
Odp: ZTE MF286R - OpenWrt
ok, jak dalej sprawdzać ?
root@OpenWrt:/# ifconfig -a
br-lan Link encap:Ethernet HWaddr C8:EA:F8:A8:FF:92
inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fdd7:d708:2e9a::1/60 Scope:Global
inet6 addr: fe80::caea:f8ff:fea8:ff92/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:2431 errors:0 dropped:0 overruns:0 frame:0
TX packets:19 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:144880 (141.4 KiB) TX bytes:3002 (2.9 KiB)
eth0 Link encap:Ethernet HWaddr C8:EA:F8:A8:FF:92
inet6 addr: fe80::caea:f8ff:fea8:ff92/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:2449 errors:0 dropped:0 overruns:0 frame:0
TX packets:41 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:190045 (185.5 KiB) TX bytes:7144 (6.9 KiB)
Interrupt:4
eth0.1 Link encap:Ethernet HWaddr C8:EA:F8:A8:FF:92
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:2431 errors:0 dropped:0 overruns:0 frame:0
TX packets:19 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:144880 (141.4 KiB) TX bytes:3002 (2.9 KiB)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:832 errors:0 dropped:0 overruns:0 frame:0
TX packets:832 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:63808 (62.3 KiB) TX bytes:63808 (62.3 KiB)
wlan0 Link encap:Ethernet HWaddr C8:EA:F8:A8:FF:92
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
root@OpenWrt:/#root@OpenWrt:/# cat /proc/mtd
dev: size erasesize name
mtd0: 000a0000 00020000 "fota-flag"
mtd1: 00080000 00020000 "art"
mtd2: 00080000 00020000 "mac"
mtd3: 01660000 00020000 "ubiconcat0"
mtd4: 00400000 00020000 "kernel"
mtd5: 06400000 00020000 "ubiconcat1"
mtd6: 000a0000 00010000 "u-boot"
mtd7: 00020000 00010000 "u-boot-env"
mtd8: 00140000 00010000 "reserved1"
mtd9: 07a60000 00020000 "ubi"
root@OpenWrt:/#Odp: ZTE MF286R - OpenWrt
Jednego radia nie ma, więc coś jest inaczej. Wrzuć logi z openwrt.
Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.
- onken
- Użytkownik
- Nieaktywny
Odp: ZTE MF286R - OpenWrt
Jak zrobić logi ? które co i jak poproszę.
Jeszcze devices:
root@OpenWrt:/# cat /sys/kernel/debug/usb/devices
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 1
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0002 Rev= 5.04
S: Manufacturer=Linux 5.4.171 ehci_hcd
S: Product=EHCI Host Controller
S: SerialNumber=1b000000.usb
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=19d2 ProdID=1489 Rev=ff.ff
S: Manufacturer=ZTE
S: Product=ZTE
S: SerialNumber=123456789ABCD
C:* #Ifs= 8 Cfg#= 1 Atr=e0 MxPwr= 2mA
A: FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=03
A: FirstIf#= 2 IfCount= 2 Cls=02(comm.) Sub=02 Prot=01
A: FirstIf#= 6 IfCount= 2 Cls=02(comm.) Sub=06 Prot=00
I:* If#= 0 Alt= 0 #EPs= 1 Cls=e0(wlcon) Sub=01 Prot=03 Driver=(none)
E: Ad=82(I) Atr=03(Int.) MxPS= 8 Ivl=1ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=(none)
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=02 Prot=01 Driver=(none)
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=(none)
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=ff Driver=(none)
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 6 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=00 Driver=(none)
E: Ad=88(I) Atr=03(Int.) MxPS= 16 Ivl=32ms
I:* If#= 7 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=00 Driver=(none)
I: If#= 7 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=(none)
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 1
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0002 Rev= 5.04
S: Manufacturer=Linux 5.4.171 ehci_hcd
S: Product=EHCI Host Controller
S: SerialNumber=1b400000.usb
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
root@OpenWrt:/#Odp: ZTE MF286R - OpenWrt
Polecenie logread
Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.
- onken
- Użytkownik
- Nieaktywny
Odp: ZTE MF286R - OpenWrt
root@OpenWrt:/# logread
Thu Feb 10 20:06:07 2022 kern.notice kernel: [ 0.000000] Linux version 5.4.171 (cezary@eko.one.pl) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r15816-b95f3caaa1)) #0 Thu Feb 10 19:06:04 2022
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 0.000000] printk: bootconsole [early0] enabled
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 0.000000] CPU0 revision is: 00019750 (MIPS 74Kc)
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 0.000000] MIPS: machine is ZTE MF286A
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 0.000000] SoC: Qualcomm Atheros QCA956X ver 1 rev 0
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 0.000000] Initrd not found or empty - disabling initrd
Thu Feb 10 20:06:07 2022 kern.warn kernel: [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Thu Feb 10 20:06:07 2022 kern.warn kernel: [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 0.000000] Zone ranges:
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 0.000000] Movable zone start for each node
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 0.000000] Early memory node ranges
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
Thu Feb 10 20:06:07 2022 kern.debug kernel: [ 0.000000] On node 0 totalpages: 32768
Thu Feb 10 20:06:07 2022 kern.debug kernel: [ 0.000000] Normal zone: 288 pages used for memmap
Thu Feb 10 20:06:07 2022 kern.debug kernel: [ 0.000000] Normal zone: 0 pages reserved
Thu Feb 10 20:06:07 2022 kern.debug kernel: [ 0.000000] Normal zone: 32768 pages, LIFO batch:7
Thu Feb 10 20:06:07 2022 kern.debug kernel: [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
Thu Feb 10 20:06:07 2022 kern.debug kernel: [ 0.000000] pcpu-alloc: [0] 0
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32480
Thu Feb 10 20:06:07 2022 kern.notice kernel: [ 0.000000] Kernel command line: console=ttyS0,115200n8 rootfstype=squashfs,jffs2
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 0.000000] Writing ErrCtl register=00000000
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 0.000000] Readback ErrCtl register=00000000
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 0.000000] Memory: 110848K/131072K available (5518K kernel code, 180K rwdata, 708K rodata, 12272K init, 210K bss, 20224K reserved, 0K cma-reserved)
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 0.000000] NR_IRQS: 51
Thu Feb 10 20:06:07 2022 kern.notice kernel: [ 0.000000] random: get_random_bytes called from 0x806a4a28 with crng_init=0
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 0.000000] CPU clock: 775.000 MHz
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4932285024 ns
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 0.000007] sched_clock: 32 bits at 387MHz, resolution 2ns, wraps every 5541893118ns
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 0.008229] Calibrating delay loop... 385.02 BogoMIPS (lpj=770048)
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 0.046722] pid_max: default: 32768 minimum: 301
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 0.051722] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 0.059435] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 0.071751] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 0.082044] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 0.089330] pinctrl core: initialized pinctrl subsystem
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 0.096082] NET: Registered protocol family 16
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 0.102418] GPIO line 19 (led:wlan) hogged as output/high
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 0.133749] clocksource: Switched to clocksource MIPS
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 0.139980] thermal_sys: Registered thermal governor 'step_wise'
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 0.140328] NET: Registered protocol family 2
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 0.151442] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 0.159786] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 0.168670] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 0.176759] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear)
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 0.184209] TCP: Hash tables configured (established 1024 bind 1024)
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 0.191035] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 0.197981] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 0.205602] NET: Registered protocol family 1
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 0.210259] PCI: CLS 0 bytes, default 32
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 0.391995] workingset: timestamp_bits=14 max_order=15 bucket_order=1
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 0.405118] squashfs: version 4.0 (2009/01/31) Phillip Lougher
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 0.411309] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 0.435366] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 0.446594] pinctrl-single 1804002c.pinmux: 544 pins, size 68
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 0.453691] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 0.462523] printk: console [ttyS0] disabled
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 0.467116] 18020000.uart: ttyS0 at MMIO 0x18020000 (irq = 9, base_baud = 1562500) is a 16550A
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 0.476224] printk: console [ttyS0] enabled
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 0.485287] printk: bootconsole [early0] disabled
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 0.505344] spi-nand spi0.1: GigaDevice SPI NAND was found.
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 0.511171] spi-nand spi0.1: 128 MiB, block size: 128 KiB, page size: 2048, OOB size: 128
Thu Feb 10 20:06:07 2022 kern.notice kernel: [ 0.520821] 6 fixed-partitions partitions found on MTD device spi0.1
Thu Feb 10 20:06:07 2022 kern.notice kernel: [ 0.527437] Creating 6 MTD partitions on "spi0.1":
Thu Feb 10 20:06:07 2022 kern.notice kernel: [ 0.532411] 0x000000000000-0x0000000a0000 : "fota-flag"
Thu Feb 10 20:06:07 2022 kern.notice kernel: [ 0.539381] 0x0000000a0000-0x000000120000 : "art"
Thu Feb 10 20:06:07 2022 kern.notice kernel: [ 0.546621] 0x000000120000-0x0000001a0000 : "mac"
Thu Feb 10 20:06:07 2022 kern.notice kernel: [ 0.553936] 0x0000001a0000-0x000001800000 : "ubiconcat0"
Thu Feb 10 20:06:07 2022 kern.notice kernel: [ 0.585347] 0x000001800000-0x000001c00000 : "kernel"
Thu Feb 10 20:06:07 2022 kern.notice kernel: [ 0.596707] 0x000001c00000-0x000008000000 : "ubiconcat1"
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 0.715537] spi-nor spi0.0: gd25q16 (2048 Kbytes)
Thu Feb 10 20:06:07 2022 kern.notice kernel: [ 0.720482] 3 fixed-partitions partitions found on MTD device spi0.0
Thu Feb 10 20:06:07 2022 kern.notice kernel: [ 0.727058] Creating 3 MTD partitions on "spi0.0":
Thu Feb 10 20:06:07 2022 kern.notice kernel: [ 0.732025] 0x000000000000-0x0000000a0000 : "u-boot"
Thu Feb 10 20:06:07 2022 kern.notice kernel: [ 0.738072] 0x0000000a0000-0x0000000c0000 : "u-boot-env"
Thu Feb 10 20:06:07 2022 kern.notice kernel: [ 0.744435] 0x0000000c0000-0x000000200000 : "reserved1"
Thu Feb 10 20:06:07 2022 kern.notice kernel: [ 0.750921] Concatenating MTD devices:
Thu Feb 10 20:06:07 2022 kern.notice kernel: [ 0.754852] (0): "ubiconcat0"
Thu Feb 10 20:06:07 2022 kern.notice kernel: [ 0.757927] (1): "ubiconcat1"
Thu Feb 10 20:06:07 2022 kern.notice kernel: [ 0.760987] into device "ubi-concat"
Thu Feb 10 20:06:07 2022 kern.notice kernel: [ 0.764714] 1 fixed-partitions partitions found on MTD device ubi-concat
Thu Feb 10 20:06:07 2022 kern.notice kernel: [ 0.771640] Creating 1 MTD partitions on "ubi-concat":
Thu Feb 10 20:06:07 2022 kern.notice kernel: [ 0.776957] 0x000000000000-0x000007a60000 : "ubi"
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 0.783838] libphy: Fixed MDIO Bus: probed
Thu Feb 10 20:06:07 2022 kern.notice kernel: [ 1.161744] random: fast init done
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 1.426115] libphy: ag71xx_mdio: probed
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 1.457086] switch0: Atheros AR8337 rev. 2 switch registered on mdio.0
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 2.045255] ag71xx 19000000.eth: connected to PHY at mdio.0:00 [uid=004dd036, driver=Atheros AR8216/AR8236/AR8316]
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 2.056523] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode: sgmii
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 2.065023] NET: Registered protocol family 10
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 2.074305] Segment Routing with IPv6
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 2.078241] NET: Registered protocol family 17
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 2.082929] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 2.096323] 8021q: 802.1Q VLAN Support v1.8
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 2.102956] PCI host bridge /ahb/pcie-controller@18250000 ranges:
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 2.109325] MEM 0x0000000012000000..0x0000000013ffffff
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 2.114743] IO 0x0000000000000000..0x0000000000000000
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 2.120308] PCI host bridge to bus 0000:00
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 2.124586] pci_bus 0000:00: root bus resource [mem 0x12000000-0x13ffffff]
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 2.131701] pci_bus 0000:00: root bus resource [io 0x0000]
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 2.137467] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 2.144481] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 2.152699] pci 0000:00:00.0: [168c:0056] type 00 class 0x028000
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 2.158967] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 2.166109] pci 0000:00:00.0: PME# supported from D0 D3hot
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 2.172791] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 2.179677] pci 0000:00:00.0: BAR 0: assigned [mem 0x12000000-0x121fffff 64bit]
Thu Feb 10 20:06:07 2022 kern.err kernel: [ 2.189695] UBI error: no valid UBI magic found inside mtd9
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 2.263598] Freeing unused kernel memory: 12272K
Thu Feb 10 20:06:07 2022 kern.warn kernel: [ 2.268394] This architecture does not have kernel memory protection.
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 2.275051] Run /init as init process
Thu Feb 10 20:06:07 2022 user.info kernel: [ 2.718576] init: Console is alive
Thu Feb 10 20:06:07 2022 user.info kernel: [ 2.722409] init: - watchdog -
Thu Feb 10 20:06:07 2022 user.info kernel: [ 2.750153] kmodloader: loading kernel modules from /etc/modules-boot.d/*
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 2.819081] usbcore: registered new interface driver usbfs
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 2.824872] usbcore: registered new interface driver hub
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 2.830474] usbcore: registered new device driver usb
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 2.890341] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Thu Feb 10 20:06:07 2022 kern.notice kernel: [ 2.904694] SCSI subsystem initialized
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 2.913031] ehci-fsl: Freescale EHCI Host controller driver
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 2.920694] ehci-platform: EHCI generic platform driver
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 2.926378] ehci-platform 1b000000.usb: EHCI Host Controller
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 2.932295] ehci-platform 1b000000.usb: new USB bus registered, assigned bus number 1
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 2.940508] ehci-platform 1b000000.usb: irq 13, io mem 0x1b000000
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 2.961759] ehci-platform 1b000000.usb: USB 2.0 started, EHCI 1.00
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 2.968954] hub 1-0:1.0: USB hub found
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 2.973273] hub 1-0:1.0: 1 port detected
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 2.977990] ehci-platform 1b400000.usb: EHCI Host Controller
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 2.983910] ehci-platform 1b400000.usb: new USB bus registered, assigned bus number 2
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 2.992138] ehci-platform 1b400000.usb: irq 14, io mem 0x1b400000
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 3.013770] ehci-platform 1b400000.usb: USB 2.0 started, EHCI 1.00
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 3.020977] hub 2-0:1.0: USB hub found
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 3.025282] hub 2-0:1.0: 1 port detected
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 3.035501] usbcore: registered new interface driver usb-storage
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 3.043813] usbcore: registered new interface driver uas
Thu Feb 10 20:06:07 2022 user.info kernel: [ 3.050175] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
Thu Feb 10 20:06:07 2022 user.info kernel: [ 3.068069] init: - preinit -
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 3.229826] usb 1-1: new high-speed USB device number 2 using ehci-platform
Thu Feb 10 20:06:07 2022 kern.notice kernel: [ 3.318205] random: jshn: uninitialized urandom read (4 bytes read)
Thu Feb 10 20:06:07 2022 kern.notice kernel: [ 3.389459] random: jshn: uninitialized urandom read (4 bytes read)
Thu Feb 10 20:06:07 2022 kern.notice kernel: [ 3.404480] random: procd: uninitialized urandom read (4 bytes read)
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 4.330645] eth0: link up (1000Mbps/Full duplex)
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 4.341634] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 4.356713] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 5.346731] Atheros AR8216/AR8236/AR8316 mdio.0:00: Port 5 is up
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 8.481382] eth0: link down
Thu Feb 10 20:06:07 2022 user.info kernel: [ 8.501683] procd: - early -
Thu Feb 10 20:06:07 2022 user.info kernel: [ 8.504818] procd: - watchdog -
Thu Feb 10 20:06:07 2022 user.info kernel: [ 9.095524] procd: - watchdog -
Thu Feb 10 20:06:07 2022 user.info kernel: [ 9.099160] procd: - ubus -
Thu Feb 10 20:06:07 2022 kern.warn kernel: [ 9.109687] urandom_read: 3 callbacks suppressed
Thu Feb 10 20:06:07 2022 kern.notice kernel: [ 9.109693] random: ubusd: uninitialized urandom read (4 bytes read)
Thu Feb 10 20:06:07 2022 kern.notice kernel: [ 9.152834] random: ubusd: uninitialized urandom read (4 bytes read)
Thu Feb 10 20:06:07 2022 kern.notice kernel: [ 9.159912] random: ubusd: uninitialized urandom read (4 bytes read)
Thu Feb 10 20:06:07 2022 user.info kernel: [ 9.169513] procd: - init -
Thu Feb 10 20:06:07 2022 user.info kernel: [ 9.733709] kmodloader: loading kernel modules from /etc/modules.d/*
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 9.802389] fuse: init (API version 7.31)
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 9.815655] Loading modules backported from Linux version v5.10.85-0-ge4f2aee6612e
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 9.823533] Backport generated by backports.git v5.10.85-1-0-gf988973f
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 9.880688] xt_time: kernel timezone is -0000
Thu Feb 10 20:06:07 2022 user.info kernel: [ 9.954144] urngd: v1.0.2 started.
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 10.020349] PPP generic driver version 2.4.2
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 10.034526] NET: Registered protocol family 24
Thu Feb 10 20:06:07 2022 kern.debug kernel: [ 10.135930] ath: EEPROM regdomain sanitized
Thu Feb 10 20:06:07 2022 kern.debug kernel: [ 10.135940] ath: EEPROM regdomain: 0x64
Thu Feb 10 20:06:07 2022 kern.debug kernel: [ 10.135943] ath: EEPROM indicates we should expect a direct regpair map
Thu Feb 10 20:06:07 2022 kern.debug kernel: [ 10.135963] ath: Country alpha2 being used: 00
Thu Feb 10 20:06:07 2022 kern.debug kernel: [ 10.135966] ath: Regpair used: 0x64
Thu Feb 10 20:06:07 2022 kern.debug kernel: [ 10.147657] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
Thu Feb 10 20:06:07 2022 kern.info kernel: [ 10.149537] ieee80211 phy0: Atheros AR9561 Rev:0 mem=0xb8100000, irq=2
Thu Feb 10 20:06:07 2022 user.info kernel: [ 10.214136] kmodloader: done loading kernel modules from /etc/modules.d/*
Thu Feb 10 20:06:07 2022 kern.notice kernel: [ 10.237233] random: crng init done
Thu Feb 10 20:06:07 2022 kern.notice kernel: [ 10.240786] random: 1 urandom warning(s) missed due to ratelimiting
Thu Feb 10 20:06:08 2022 user.notice dnsmasq: DNS rebinding protection is active, will discard upstream RFC1918 responses!
Thu Feb 10 20:06:08 2022 user.notice dnsmasq: Allowing 127.0.0.0/8 responses
Thu Feb 10 20:06:08 2022 daemon.info dnsmasq[1265]: Connected to system UBus
Thu Feb 10 20:06:08 2022 daemon.info dnsmasq[1265]: started, version 2.85 cachesize 150
Thu Feb 10 20:06:08 2022 daemon.info dnsmasq[1265]: DNS service limited to local subnets
Thu Feb 10 20:06:08 2022 daemon.info dnsmasq[1265]: compile time options: IPv6 GNU-getopt no-DBus UBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth no-cryptohash no-DNSSEC no-ID loop-detect inotify dumpfile
Thu Feb 10 20:06:08 2022 daemon.info dnsmasq[1265]: UBus support enabled: connected to system bus
Thu Feb 10 20:06:08 2022 daemon.info dnsmasq[1265]: using only locally-known addresses for domain test
Thu Feb 10 20:06:08 2022 daemon.info dnsmasq[1265]: using only locally-known addresses for domain onion
Thu Feb 10 20:06:08 2022 daemon.info dnsmasq[1265]: using only locally-known addresses for domain localhost
Thu Feb 10 20:06:08 2022 daemon.info dnsmasq[1265]: using only locally-known addresses for domain local
Thu Feb 10 20:06:08 2022 daemon.info dnsmasq[1265]: using only locally-known addresses for domain invalid
Thu Feb 10 20:06:08 2022 daemon.info dnsmasq[1265]: using only locally-known addresses for domain bind
Thu Feb 10 20:06:08 2022 daemon.info dnsmasq[1265]: using only locally-known addresses for domain lan
Thu Feb 10 20:06:08 2022 daemon.warn dnsmasq[1265]: no servers found in /tmp/resolv.conf.d/resolv.conf.auto, will retry
Thu Feb 10 20:06:08 2022 daemon.info dnsmasq[1265]: read /etc/hosts - 4 addresses
Thu Feb 10 20:06:08 2022 daemon.info dnsmasq[1265]: read /tmp/hosts/dhcp.cfg01411c - 0 addresses
Thu Feb 10 20:06:34 2022 authpriv.info dropbear[1331]: Not backgrounding
Thu Feb 10 20:06:35 2022 daemon.notice wpa_supplicant[1430]: Successfully initialized wpa_supplicant
Thu Feb 10 20:06:36 2022 user.notice : Added device handler type: bonding
Thu Feb 10 20:06:36 2022 user.notice : Added device handler type: 8021ad
Thu Feb 10 20:06:36 2022 user.notice : Added device handler type: 8021q
Thu Feb 10 20:06:36 2022 user.notice : Added device handler type: macvlan
Thu Feb 10 20:06:36 2022 user.notice : Added device handler type: veth
Thu Feb 10 20:06:36 2022 user.notice : Added device handler type: bridge
Thu Feb 10 20:06:36 2022 user.notice : Added device handler type: Network device
Thu Feb 10 20:06:36 2022 user.notice : Added device handler type: tunnel
Thu Feb 10 20:06:41 2022 kern.info kernel: [ 47.015870] eth0: link up (1000Mbps/Full duplex)
Thu Feb 10 20:06:41 2022 kern.info kernel: [ 47.033819] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Thu Feb 10 20:06:41 2022 kern.info kernel: [ 47.041442] br-lan: port 1(eth0.1) entered blocking state
Thu Feb 10 20:06:41 2022 kern.info kernel: [ 47.047090] br-lan: port 1(eth0.1) entered disabled state
Thu Feb 10 20:06:41 2022 kern.info kernel: [ 47.053077] device eth0.1 entered promiscuous mode
Thu Feb 10 20:06:41 2022 kern.info kernel: [ 47.058073] device eth0 entered promiscuous mode
Thu Feb 10 20:06:41 2022 kern.info kernel: [ 47.118908] br-lan: port 1(eth0.1) entered blocking state
Thu Feb 10 20:06:41 2022 kern.info kernel: [ 47.124541] br-lan: port 1(eth0.1) entered forwarding state
Thu Feb 10 20:06:41 2022 daemon.notice netifd: Interface 'lan' is enabled
Thu Feb 10 20:06:41 2022 daemon.notice netifd: Interface 'lan' is setting up now
Thu Feb 10 20:06:41 2022 daemon.notice netifd: Interface 'lan' is now up
Thu Feb 10 20:06:41 2022 daemon.notice netifd: bridge 'br-lan' link is up
Thu Feb 10 20:06:41 2022 daemon.notice netifd: Interface 'lan' has link connectivity
Thu Feb 10 20:06:41 2022 daemon.notice netifd: VLAN 'eth0.1' link is up
Thu Feb 10 20:06:41 2022 daemon.notice netifd: Interface 'loopback' is enabled
Thu Feb 10 20:06:41 2022 daemon.notice netifd: Interface 'loopback' is setting up now
Thu Feb 10 20:06:41 2022 daemon.notice netifd: Interface 'loopback' is now up
Thu Feb 10 20:06:41 2022 daemon.notice netifd: Network device 'eth0' link is up
Thu Feb 10 20:06:41 2022 daemon.notice netifd: Network device 'lo' link is up
Thu Feb 10 20:06:41 2022 daemon.notice netifd: Interface 'loopback' has link connectivity
Thu Feb 10 20:06:42 2022 user.notice firewall: Reloading firewall due to ifup of lan (br-lan)
Thu Feb 10 20:06:42 2022 kern.info kernel: [ 48.033839] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
Thu Feb 10 20:06:42 2022 daemon.err odhcpd[1549]: Failed to send to ff02::1%lan@br-lan (Address not available)
Thu Feb 10 20:06:47 2022 daemon.info dnsmasq[1265]: exiting on receipt of SIGTERM
Thu Feb 10 20:06:48 2022 daemon.info dnsmasq[1916]: Connected to system UBus
Thu Feb 10 20:06:48 2022 daemon.info dnsmasq[1916]: started, version 2.85 cachesize 150
Thu Feb 10 20:06:48 2022 daemon.info dnsmasq[1916]: DNS service limited to local subnets
Thu Feb 10 20:06:48 2022 daemon.info dnsmasq[1916]: compile time options: IPv6 GNU-getopt no-DBus UBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth no-cryptohash no-DNSSEC no-ID loop-detect inotify dumpfile
Thu Feb 10 20:06:48 2022 daemon.info dnsmasq[1916]: UBus support enabled: connected to system bus
Thu Feb 10 20:06:48 2022 daemon.info dnsmasq-dhcp[1916]: DHCP, IP range 192.168.1.100 -- 192.168.1.249, lease time 12h
Thu Feb 10 20:06:48 2022 daemon.info dnsmasq[1916]: using only locally-known addresses for domain test
Thu Feb 10 20:06:48 2022 daemon.info dnsmasq[1916]: using only locally-known addresses for domain onion
Thu Feb 10 20:06:48 2022 daemon.info dnsmasq[1916]: using only locally-known addresses for domain localhost
Thu Feb 10 20:06:48 2022 daemon.info dnsmasq[1916]: using only locally-known addresses for domain local
Thu Feb 10 20:06:48 2022 daemon.info dnsmasq[1916]: using only locally-known addresses for domain invalid
Thu Feb 10 20:06:48 2022 daemon.info dnsmasq[1916]: using only locally-known addresses for domain bind
Thu Feb 10 20:06:48 2022 daemon.info dnsmasq[1916]: using only locally-known addresses for domain lan
Thu Feb 10 20:06:48 2022 daemon.warn dnsmasq[1916]: no servers found in /tmp/resolv.conf.d/resolv.conf.auto, will retry
Thu Feb 10 20:06:48 2022 daemon.info dnsmasq[1916]: read /etc/hosts - 4 addresses
Thu Feb 10 20:06:48 2022 daemon.info dnsmasq[1916]: read /tmp/hosts/dhcp.cfg01411c - 2 addresses
Thu Feb 10 20:06:48 2022 daemon.info dnsmasq-dhcp[1916]: read /etc/ethers - 0 addresses
Thu Feb 10 20:06:48 2022 daemon.info dnsmasq[1916]: read /etc/hosts - 4 addresses
Thu Feb 10 20:06:48 2022 daemon.info dnsmasq[1916]: read /tmp/hosts/dhcp.cfg01411c - 2 addresses
Thu Feb 10 20:06:48 2022 daemon.info dnsmasq-dhcp[1916]: read /etc/ethers - 0 addresses
Thu Feb 10 20:06:49 2022 daemon.info procd: - init complete -
Thu Feb 10 20:06:49 2022 daemon.info urandom_seed[2129]: Seed saved (/etc/urandom.seed)
root@OpenWrt:/#25 2022-02-15 21:14:13 (edytowany przez Leo-PL 2022-02-15 21:17:15)
Odp: ZTE MF286R - OpenWrt
A nie brakuje w initramfsie drivera do wi-fi, że w ogóle się nie probuje? Zrób "opkg list | grep ath10k" w tym initramfsie i pokaż, co wypluje.
Lokalizacja na magistrali i PCI ID się zgadzają. Wygląda na to, że faktycznie co do joty ten sam HW w części routerowej.
Sprawdzę, jak dodać USB ID do kernela do tego modemu. Szkoda, że używa tego parszywego RNDISa, a nie np MBIM 
Posty: 1 do 25 z 1,243
Zaloguj się lub zarejestruj by napisać odpowiedź
eko.one.pl → Sprzęt / Hardware → ZTE MF286R - OpenWrt
Forum oparte o PunBB, wspierane przez Informer Technologies, Inc