FAQ o OpenWrt | Sprzedam różne routery | Oddam

sidors85 · 2022-02-02 17:41:32

sidors85
Użytkownik
Nieaktywny

Zarejestrowany: 2022-02-02
Posty: 12

Temat: Xiaomi router 3G problem po update

Witam wszystkich, mam problem z routerem od Xiaomi (Xiaomi router 3G v1) był długo nie używany aż w końcu znalazłem dla niego zastosowanie,
już kiedyś wgrałem mu OpenWRT z luci w wersji 18.06 teraz chciałem mu zrobić update do 21.06
image pobrałem strony z eko.one.pl przez luci nie chciał przyjąć pliku sysupgrade ale rootfs0 już tak.

po restarcie kontrolka świeci się na pomarańczowo (normalnie przy wypełni uruchomionym routerze świeci się na niebiesko) router nadaje adresacje 169.254.x.x wiec DHCP nie działa
ustawiłem manualnie adresacje na karcie sieciowej 192.168.1.2 ale nie ma ping'a na 192.168.1.1.

próbowałem robić kolejny reset ale nic nie zadziałało, wiem ze xiaomi ma recovery po USB testowałem wiele wariantów z image ale tez zero reakcji.

udało się połączyć z konsola (putty) przez wlutowanie pinów i widzę ze jest obraz 21.06 uruchamia się do linii komend, nie widzę żadnego błędu, testowałem wszystkie opcje recovery jakie znalazłem ale dalej nie chce się załadować DHCP i nie mogę się połączyć przez LAN

może ktoś ma jakiś pomysł jak go ożywić?

Cezary · 2022-02-02 17:44:09

Cezary
...
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2006-02-25
Posty: 117,012

Odp: Xiaomi router 3G problem po update

Jak zrobiłeś aktualizację zachowaniem zmian to siec się nie zgadza. usuń plik /etc/config/network i zrestartuj go ponownie.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

sidors85 · 2022-02-02 19:19:03

sidors85
Użytkownik
Nieaktywny

Zarejestrowany: 2022-02-02
Posty: 12

Odp: Xiaomi router 3G problem po update

Hej Cezary, wielkie dzięki za szybka odpowiedz.

Usunąłem /etc/config/network ale po reboot jest to samo

Przed update zrobiłem reset do factory bo zapomniałem hasła wiec nie bardzo miał co zachowywać ze starych ustawień.

dalej nie ma ping'a po ustawieniu manualnie adresacji np. 192.168.1.2, DHCP nie dziala

Dodaje zrzut z putty.

===================================================================
                MT7621   stage1 code 10:33:11 (ASIC)
                CPU=50000000 HZ BUS=12500000 HZ
==================================================================
Change MPLL source from XTAL to CR...
do MEMPLL setting..
MEMPLL Config : 0x11100000
3PLL mode + External loopback
=== XTAL-40Mhz === DDR-1200Mhz ===
PLL2 FB_DL: 0xc, 1/0 = 632/392 31000000
PLL3 FB_DL: 0xd, 1/0 = 675/349 35000000
PLL4 FB_DL: 0x16, 1/0 = 629/395 59000000
do DDR setting..[00320381]
Apply DDR3 Setting...(use customer AC)
          0    8   16   24   32   40   48   56   64   72   80   88   96  104  112  120
      --------------------------------------------------------------------------------
0000:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0001:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0002:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0003:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0004:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0005:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0006:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0007:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0008:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0009:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
000A:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
000B:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
000C:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
000D:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    1    1
000E:|    0    0    0    0    0    0    0    0    0    1    1    1    1    1    1    1
000F:|    0    0    0    0    1    1    1    1    1    1    1    1    1    1    0    0
0010:|    1    1    1    1    1    1    1    1    1    0    0    0    0    0    0    0
0011:|    1    1    1    0    0    0    0    0    0    0    0    0    0    0    0    0
0012:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0013:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0014:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0015:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0016:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0017:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0018:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0019:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
001A:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
001B:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
001C:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
001D:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
001E:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
001F:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
rank 0 coarse = 15
rank 0 fine = 72
B:|    0    0    0    0    0    0    0    1    1    1    0    0    0    0    0    0
opt_dle value:8
DRAMC_R0DELDLY[018]=00002020
==================================================================
                RX      DQS perbit delay software calibration
==================================================================
1.0-15 bit dq delay value
==================================================================
bit|     0  1  2  3  4  5  6  7  8  9
--------------------------------------
0 |    9 7 9 9 7 7 7 6 5 6
10 |    7 9 9 10 7 9
--------------------------------------

==================================================================
2.dqs window
x=pass dqs delay value (min~max)center
y=0-7bit DQ of every group
input delay:DQS0 =32 DQS1 = 32
==================================================================
bit     DQS0     bit      DQS1
0  (0~60)30  8  (1~60)30
1  (1~58)29  9  (1~61)31
2  (2~61)31  10  (1~61)31
3  (1~59)30  11  (1~59)30
4  (0~60)30  12  (2~62)32
5  (2~62)32  13  (0~62)31
6  (1~60)30  14  (1~62)31
7  (2~63)32  15  (1~62)31
==================================================================
3.dq delay value last
==================================================================
bit|    0  1  2  3  4  5  6  7  8   9
--------------------------------------
0 |    11 10 10 11 9 7 9 6 7 7
10 |    8 11 9 11 8 10
==================================================================
==================================================================
     TX  perbyte calibration
==================================================================
DQS loop = 15, cmp_err_1 = ffff0000
dqs_perbyte_dly.last_dqsdly_pass[0]=15,  finish count=1
dqs_perbyte_dly.last_dqsdly_pass[1]=15,  finish count=2
DQ loop=15, cmp_err_1 = ffff0000
dqs_perbyte_dly.last_dqdly_pass[0]=15,  finish count=1
dqs_perbyte_dly.last_dqdly_pass[1]=15,  finish count=2
byte:0, (DQS,DQ)=(8,8)
byte:1, (DQS,DQ)=(8,8)
20,data:88
[EMI] DRAMC calibration passed

===================================================================
                MT7621   stage1 code done
                CPU=50000000 HZ BUS=12500000 HZ
===================================================================


U-Boot 1.1.3 (Apr 17 2017 - 17:00:02)

Board: Ralink APSoC DRAM:  256 MB
Power on memory test. Memory size= 256 MB...OK!
relocate_code Pointer at: 8ffac000

Config XHCI 40M PLL
Allocate 16 byte aligned buffer: 8ffdffd0
Enable NFI Clock
# MTK NAND # : Use HW ECC
NAND ID [C8 D1 80 95 42]
Device not found, ID: c8d1
Not Support this Device!
chip_mode=00000001
Support this Device in MTK table! c8d1
select_chip
[NAND]select ecc bit:4, sparesize :64 spare_per_sector=16
Signature matched and data read!
load_fact_bbt success 1023
load fact bbt success
[mtk_nand] probe successfully!
mtd->writesize=2048 mtd->oobsize=64,    mtd->erasesize=131072  devinfo.iowidth=8
..============================================
Ralink UBoot Version: 5.0.0.0
--------------------------------------------
ASIC MT7621A DualCore (MAC to MT7530 Mode)
DRAM_CONF_FROM: Auto-Detection
DRAM_TYPE: DDR3
DRAM bus: 16 bit
Xtal Mode=5 OCP Ratio=1/4
Flash component: NAND Flash
Date:Apr 17 2017  Time:17:00:02
============================================
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:256, ways:4, linesz:32 ,total:32768

 ##### The CPU freq = 880 MHZ ####
 estimate memory size =256 Mbytes
#Reset_MT7530
set LAN/WAN LWLLL

Please choose the operation:
   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   7: Load Boot Loader code then write to Flash via Serial.
   9: Load Boot Loader code then write to Flash via TFTP.                     0
Booting System 2
..Erasing NAND Flash...
ranand_erase: start:80000, len:20000
.Writing to NAND Flash...
done

3: System Boot system code via Flash.
## Booting image at bc600000 ...
   Image Name:   MIPS OpenWrt Linux-4.14.77
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1828902 Bytes =  1.7 MB
   Load Address: 80001000
   Entry Point:  80001000
............................   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
commandline uart_en=0 factory_mode=0 usb_u3=0
No initrd
## Transferring control to Linux (at address 80001000) ...
## Giving linux memsize in MB, 256

Starting kernel ...

[    0.000000] Linux version 4.14.77 (cezary@eko.one.pl) (gcc version 7.3.0 (OpenWrt GCC 7.3.0 r7353-486dc7583d)) #0 SMP Fri Oct 19 08:00:48 2018
[    0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[    0.000000] MIPS: machine is Xiaomi Mi Router 3G
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 10000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] VPE topology {2,2} total 4
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x000000000fffffff]
[    0.000000]   HighMem  empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x000000000fffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff]
[    0.000000] random: get_random_bytes called from 0x80551740 with crng_init=0
[    0.000000] percpu: Embedded 14 pages/cpu @81210000 s26256 r8192 d22896 u57344
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 65024
[    0.000000] Kernel command line: console=ttyS0,115200n8 rootfstype=squashfs,jffs2
[    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Writing ErrCtl register=0000019f
[    0.000000] Readback ErrCtl register=0000019f
[    0.000000] Memory: 253616K/262144K available (4621K kernel code, 242K rwdata, 568K rodata, 252K init, 254K bss, 8528K reserved, 0K cma-reserved, 0K highmem)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS: 256
[    0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns
[    0.000009] sched_clock: 32 bits at 440MHz, resolution 2ns, wraps every 4880645118ns
[    0.007808] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688)
[    0.073974] pid_max: default: 32768 minimum: 301
[    0.078739] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.085247] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.094026] Hierarchical SRCU implementation.
[    0.099175] smp: Bringing up secondary CPUs ...
[    0.108473] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.108482] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.108494] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[    0.108628] CPU1 revision is: 0001992f (MIPS 1004Kc)
[    0.163917] Synchronize counters for CPU 1: done.
[    0.202572] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.202581] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.202590] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[    0.202661] CPU2 revision is: 0001992f (MIPS 1004Kc)
[    0.255032] Synchronize counters for CPU 2: done.
[    0.289609] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.289617] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.289625] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[    0.289702] CPU3 revision is: 0001992f (MIPS 1004Kc)
[    0.340214] Synchronize counters for CPU 3: done.
[    0.370077] smp: Brought up 1 node, 4 CPUs
[    0.377812] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.387596] futex hash table entries: 1024 (order: 3, 32768 bytes)
[    0.393888] pinctrl core: initialized pinctrl subsystem
[    0.399691] NET: Registered protocol family 16
[    0.410045] Can't analyze schedule() prologue at 8047efd4
[    0.416117] pull PCIe RST: RALINK_RSTCTRL = 4000000
[    0.721348] release PCIe RST: RALINK_RSTCTRL = 7000000
[    0.726381] ***** Xtal 40MHz *****
[    0.729755] release PCIe RST: RALINK_RSTCTRL = 7000000
[    0.734861] Port 0 N_FTS = 1b102800
[    0.738304] Port 1 N_FTS = 1b102800
[    0.741763] Port 2 N_FTS = 1b102800
[    1.896971] PCIE2 no card, disable it(RST&CLK)
[    1.901320]  -> 21007f2
[    1.903735] PCIE0 enabled
[    1.906342] PCIE1 enabled
[    1.908929] PCI host bridge /pcie@1e140000 ranges:
[    1.913691]  MEM 0x0000000060000000..0x000000006fffffff
[    1.918874]   IO 0x000000001e160000..0x000000001e16ffff
[    1.924048] PCI coherence region base: 0xbfbf8000, mask/settings: 0x60000000
[    1.939817] mt7621_gpio 1e000600.gpio: registering 32 gpios
[    1.945654] mt7621_gpio 1e000600.gpio: registering 32 gpios
[    1.951369] mt7621_gpio 1e000600.gpio: registering 32 gpios
[    1.958461] PCI host bridge to bus 0000:00
[    1.962498] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
[    1.969323] pci_bus 0000:00: root bus resource [io  0xffffffff]
[    1.975178] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    1.981938] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    1.990603] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    1.998525] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    2.007818] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[    2.014348] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[    2.021242] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000]
[    2.027823] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000]
[    2.034725] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
[    2.041475] pci 0000:00:01.0: BAR 8: assigned [mem 0x60100000-0x601fffff]
[    2.048205] pci 0000:00:01.0: BAR 9: assigned [mem 0x60200000-0x602fffff pref]
[    2.055386] pci 0000:00:00.0: BAR 1: assigned [mem 0x60300000-0x6030ffff]
[    2.062112] pci 0000:00:01.0: BAR 1: assigned [mem 0x60310000-0x6031ffff]
[    2.068876] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff]
[    2.075593] pci 0000:00:00.0: PCI bridge to [bus 01]
[    2.080528] pci 0000:00:00.0:   bridge window [mem 0x60000000-0x600fffff]
[    2.087265] pci 0000:02:00.0: BAR 0: assigned [mem 0x60100000-0x601fffff 64bit]
[    2.094535] pci 0000:02:00.0: BAR 6: assigned [mem 0x60200000-0x6020ffff pref]
[    2.101677] pci 0000:00:01.0: PCI bridge to [bus 02]
[    2.106627] pci 0000:00:01.0:   bridge window [mem 0x60100000-0x601fffff]
[    2.113341] pci 0000:00:01.0:   bridge window [mem 0x60200000-0x602fffff pref]
[    2.121967] clocksource: Switched to clocksource GIC
[    2.128452] NET: Registered protocol family 2
[    2.133553] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[    2.140437] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
[    2.146860] TCP: Hash tables configured (established 2048 bind 2048)
[    2.153266] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    2.159028] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    2.165474] NET: Registered protocol family 1
[    2.401911] 4 CPUs re-calibrate udelay(lpj = 2924544)
[    2.408374] Crashlog allocated RAM at address 0x3f00000
[    2.413825] workingset: timestamp_bits=30 max_order=16 bucket_order=0
[    2.427525] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    2.433332] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    2.445848] random: fast init done
[    2.449940] io scheduler noop registered
[    2.453831] io scheduler deadline registered (default)
[    2.459489] gpio-export gpio_export: 1 gpio(s) exported
[    2.465535] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    2.474918] console [ttyS0] disabled
[    2.478469] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 18, base_baud = 3125000) is a 16550A
[    2.487480] console [ttyS0] enabled
[    2.487480] console [ttyS0] enabled
[    2.494358] bootconsole [early0] disabled
[    2.494358] bootconsole [early0] disabled
[    2.503101] cacheinfo: Failed to find cpu0 device node
[    2.508220] cacheinfo: Unable to detect cache hierarchy for CPU 0
[    2.515166] MediaTek Nand driver init, version v2.1 Fix AHB virt2phys error
[    2.522330] Enable NFI Clock
[    2.525202] # MTK NAND # : Use HW ECC
[    2.528861] Device not found, ID: c8d1
[    2.532609] Not Support this Device!
[    2.536336] chip_mode=00000001
[    2.539373] Support this Device in MTK table! c8d1
[    2.544342] [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16
[    2.550799] nand: device found, Manufacturer ID: 0xc8, Chip ID: 0xd1
[    2.557136] nand: ESMT NAND 128MiB 3,3V 8-bit
[    2.561471] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    2.569040] Scanning device for bad blocks
[    2.718029] 10 fixed-partitions partitions found on MTD device MT7621-NAND
[    2.724888] Creating 10 MTD partitions on "MT7621-NAND":
[    2.730183] 0x000000000000-0x000000080000 : "Bootloader"
[    2.736613] 0x000000080000-0x0000000c0000 : "Config"
[    2.742671] 0x0000000c0000-0x000000100000 : "Bdata"
[    2.748535] 0x000000100000-0x000000140000 : "Factory"
[    2.754624] 0x000000140000-0x000000180000 : "crash"
[    2.760483] 0x000000180000-0x0000001c0000 : "crash_syslog"
[    2.766992] 0x0000001c0000-0x000000200000 : "reserved0"
[    2.773283] 0x000000200000-0x000000600000 : "kernel_stock"
[    2.779785] 0x000000600000-0x000000a00000 : "kernel"
[    2.785809] 0x000000a00000-0x000007f80000 : "ubi"
[    2.792557] [mtk_nand] probe successfully!
[    2.797372] Signature matched and data read!
[    2.801616] load_fact_bbt success 1023
[    2.806149] libphy: Fixed MDIO Bus: probed
[    2.874521] libphy: mdio: probed
[    4.278098] mtk_soc_eth 1e100000.ethernet: loaded mt7530 driver
[    4.284800] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 20
[    4.295603] NET: Registered protocol family 10
[    4.301416] Segment Routing with IPv6
[    4.305200] NET: Registered protocol family 17
[    4.309677] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    4.322598] 8021q: 802.1Q VLAN Support v1.8
[    4.329722] UBI: auto-attach mtd9
[    4.333117] ubi0: attaching mtd9
[    5.443347] ubi0: scanning is finished
[    5.463477] ubi0: attached mtd9 (name "ubi", size 117 MiB)
[    5.468950] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    5.475853] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    5.482624] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[    5.489551] ubi0: good PEBs: 940, bad PEBs: 0, corrupted PEBs: 0
[    5.495542] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[    5.502744] ubi0: max/mean erase counter: 4/3, WL threshold: 4096, image sequence number: 13356660
[    5.511659] ubi0: available PEBs: 0, total reserved PEBs: 940, PEBs reserved for bad PEB handling: 20
[    5.520870] ubi0: background thread "ubi_bgt0d" started, PID 387
[    5.522561] block ubiblock0_0: created from ubi0:0(rootfs)
[    5.522575] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
[    5.522600] hctosys: unable to open rtc device (rtc0)
[    5.551705] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[    5.559433] Freeing unused kernel memory: 252K
[    5.563915] This architecture does not have kernel memory protection.
[    6.132793] init: Console is alive
[    6.136427] init: - watchdog -
[    6.192961] kmodloader: no module folders for kernel version 4.14.77 found
[    6.212268] init: - preinit -
[    6.913346] mtk_soc_eth 1e100000.ethernet: PPE started
[    7.060308] random: jshn: uninitialized urandom read (4 bytes read)
[    7.121861] random: jshn: uninitialized urandom read (4 bytes read)
[    7.159835] random: jshn: uninitialized urandom read (4 bytes read)
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[   11.509861] mount_root: loading kmods from internal overlay
[   11.520634] kmodloader: no module folders for kernel version 4.14.77 found
[   11.528073] mount_root: failed to launch kmodloader from internal overlay
[   12.043638] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 483
[   12.097782] urandom_read: 6 callbacks suppressed
[   12.097795] random: procd: uninitialized urandom read (4 bytes read)
[   12.118572] UBIFS (ubi0:1): recovery needed
[   12.286845] UBIFS (ubi0:1): recovery completed
[   12.291428] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[   12.299242] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[   12.309132] UBIFS (ubi0:1): FS size: 108183552 bytes (103 MiB, 852 LEBs), journal size 5459968 bytes (5 MiB, 43 LEBs)
[   12.319702] UBIFS (ubi0:1): reserved for root: 4952683 bytes (4836 KiB)
[   12.326302] UBIFS (ubi0:1): media format: w4/r0 (latest is w5/r0), UUID 9BC78FC8-F6B2-429B-865C-59CDD6234F3A, small LPT model
[   12.339671] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[   12.357394] block: extroot: not configured
[   12.402194] UBIFS (ubi0:1): un-mount UBI device 0
[   12.406908] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" stops
[   12.419172] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 486
[   12.585942] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[   12.593774] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[   12.603659] UBIFS (ubi0:1): FS size: 108183552 bytes (103 MiB, 852 LEBs), journal size 5459968 bytes (5 MiB, 43 LEBs)
[   12.614238] UBIFS (ubi0:1): reserved for root: 4952683 bytes (4836 KiB)
[   12.620825] UBIFS (ubi0:1): media format: w4/r0 (latest is w5/r0), UUID 9BC78FC8-F6B2-429B-865C-59CDD6234F3A, small LPT model
[   13.002057] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[   13.018543] block: extroot: not configured
[   13.065400] mount_root: switching to ubifs overlay
[   13.082716] urandom-seed: Seeding with /etc/urandom.seed
[   13.181266] procd: - early -
[   13.184292] procd: - watchdog -
[   13.818284] procd: - watchdog -
[   13.842253] procd: - ubus -
[   14.018181] procd: - init -
Please press Enter to activate this console.
[   14.710718] kmodloader: no module folders for kernel version 4.14.77 found
[   14.913836] urngd: v1.0.2 started.
[   15.051650] random: crng init done



BusyBox v1.33.2 (2022-01-15 21:49:28 UTC) built-in shell (ash)

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 -----------------------------------------------------------------------------
 |                                                                           |
 | OpenWrt 21.02-SNAPSHOT, r16470-6eced97ce4                                 |
 |                                                                           |
 | Build time: 2022-01-16 15:36 CET                                          |
 | Cezary Jackiewicz, [url]https://eko.one.pl[/url]                                     |
 |                                                                           |
 -----------------------------------------------------------------------------
 | Machine: Xiaomi Mi Router 3G                                              |
 | Uptime: 0d, 00:00:19                                                      |
 | Load: 0.15 0.03 0.01                                                      |
 | Flash: total: 94.8MB, free: 90.0MB, used: 0%                              |
 | Memory: total: 247.9MB, free: 226.1MB, used: 8%                           |
 | Leases: 0                                                                 |
 | lan: static, 192.168.1.1                                                  |
 | wan: dhcp, ?                                                              |
 | wan6: dhcpv6, ?                                                           |
 -----------------------------------------------------------------------------
 === WARNING! ================================================================
 There is no root password defined on this device!
 Use the "passwd" command to set up a new password
 in order to prevent unauthorized SSH logins.
 -----------------------------------------------------------------------------
root@OpenWrt:/# block info
/dev/mtdblock9: UUID="13356660" VERSION="1" TYPE="ubi"
/dev/ubiblock0_0: UUID="992f082e-ca40abad-19f72551-45cc2a68" VERSION="4.0" MOUNT="/rom" TYPE="squashfs"
/dev/ubi0_1: UUID="9bc78fc8-f6b2-429b-865c-59cdd6234f3a" VERSION="w4r0" MOUNT="/overlay" TYPE="ubifs"
root@OpenWrt:/# ifconfig
eth0      Link encap:Ethernet  HWaddr 34:CE:00:6A:7F:B5
          inet6 addr: fe80::36ce:ff:fe6a:7fb5/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:9 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:882 (882.0 B)
          Interrupt:20

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:65536  Metric:1
          RX packets:104 errors:0 dropped:0 overruns:0 frame:0
          TX packets:104 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:7720 (7.5 KiB)  TX bytes:7720 (7.5 KiB)

root@OpenWrt:/#
root@OpenWrt:/# [  251.882425] mtk_soc_eth 1e100000.ethernet eth0: port 2 link up
[  252.637006] mtk_soc_eth 1e100000.ethernet eth0: port 2 link down
[  255.585664] mtk_soc_eth 1e100000.ethernet eth0: port 2 link up

root@OpenWrt:/# ifconfig
eth0      Link encap:Ethernet  HWaddr 34:CE:00:6A:7F:B5
          inet6 addr: fe80::36ce:ff:fe6a:7fb5/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:364 errors:0 dropped:3 overruns:0 frame:0
          TX packets:9 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:54482 (53.2 KiB)  TX bytes:882 (882.0 B)
          Interrupt:20

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:65536  Metric:1
          RX packets:748 errors:0 dropped:0 overruns:0 frame:0
          TX packets:748 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:54076 (52.8 KiB)  TX bytes:54076 (52.8 KiB)

root@OpenWrt:/#

Cezary · 2022-02-02 19:22:13

Cezary
...
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2006-02-25
Posty: 117,012

Odp: Xiaomi router 3G problem po update

Czy pojawił się /etc/config/network?

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

sidors85 · 2022-02-02 19:28:11

sidors85
Użytkownik
Nieaktywny

Zarejestrowany: 2022-02-02
Posty: 12

Odp: Xiaomi router 3G problem po update

tak, o to co jest w środku

config interface 'loopback'
        option device 'lo'
        option proto 'static'
        option ipaddr '127.0.0.1'
        option netmask '255.0.0.0'

config globals 'globals'
        option ula_prefix 'auto'

config device
        option name 'br-lan'
        option type 'bridge'
        list ports 'lan1'
        list ports 'lan2'
        list ports 'lan3'
        list ports 'lan4'

config interface 'lan'
        option device 'br-lan'
        option proto 'static'
        option ipaddr '192.168.1.1'
        option netmask '255.255.255.0'
        option ip6assign '60'

config interface 'wan'
        option device 'wan'
        option proto 'dhcp'

config interface 'wan6'
        option device 'wan'
        option proto 'dhcpv6'

Cezary · 2022-02-02 19:33:53

Cezary
...
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2006-02-25
Posty: 117,012

Odp: Xiaomi router 3G problem po update

I jeszcze raz pokaż ifconfig .Tylko go nie resetuj teraz.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

sidors85 · 2022-02-02 19:35:02

sidors85
Użytkownik
Nieaktywny

Zarejestrowany: 2022-02-02
Posty: 12

Odp: Xiaomi router 3G problem po update

root@OpenWrt:/# ifconfig
eth0 Link encap:Ethernet HWaddr 34:CE:00:6A:7F:B5
inet6 addr: fe80::36ce:ff:fe6a:7fb5/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:9 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:882 (882.0 B)
Interrupt:20

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:1120 errors:0 dropped:0 overruns:0 frame:0
TX packets:1120 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:79744 (77.8 KiB) TX bytes:79744 (77.8 KiB)

Cezary · 2022-02-02 19:35:48

Cezary
...
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2006-02-25
Posty: 117,012

Odp: Xiaomi router 3G problem po update

Sieć ci w ogóle nie wstała. Wpisz firstboot, potwierdź i go zresetuj.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

sidors85 · 2022-02-02 19:41:33

sidors85
Użytkownik
Nieaktywny

Zarejestrowany: 2022-02-02
Posty: 12

Odp: Xiaomi router 3G problem po update

zrobione, ten sam wynik.

root@OpenWrt:/# [   57.762850] mtk_soc_eth 1e100000.ethernet eth0: port 2 link down
[   61.028456] mtk_soc_eth 1e100000.ethernet eth0: port 2 link up

root@OpenWrt:/# ifconfig
eth0      Link encap:Ethernet  HWaddr 34:CE:00:6A:7F:B5
          inet6 addr: fe80::36ce:ff:fe6a:7fb5/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:7 errors:0 dropped:3 overruns:0 frame:0
          TX packets:9 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:1012 (1012.0 B)  TX bytes:882 (882.0 B)
          Interrupt:20

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:65536  Metric:1
          RX packets:104 errors:0 dropped:0 overruns:0 frame:0
          TX packets:104 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:7720 (7.5 KiB)  TX bytes:7720 (7.5 KiB)

sidors85 · 2022-02-02 19:43:07

sidors85
Użytkownik
Nieaktywny

Zarejestrowany: 2022-02-02
Posty: 12

Odp: Xiaomi router 3G problem po update

można mu wgrać jeszcze raz image przez konsole?

testowałem
https://www.youtube.com/watch?v=AAii7RxG1NY

ale bez pinga nie poszło

Cezary · 2022-02-02 19:44:25

Cezary
...
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2006-02-25
Posty: 117,012

Odp: Xiaomi router 3G problem po update

Możesz sobie wifi włączyć i normalnie się do niego do łączyć.

Pokaż jeszcze ifconfig -a i zobacz czy wstanie po /etc/init.d/network start

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

sidors85 · 2022-02-02 19:47:53

sidors85
Użytkownik
Nieaktywny

Zarejestrowany: 2022-02-02
Posty: 12

Odp: Xiaomi router 3G problem po update

znowu zero reakcji.

root@OpenWrt:/# /etc/init.d/network start
root@OpenWrt:/# ifconfig -a
eth0      Link encap:Ethernet  HWaddr 34:CE:00:6A:7F:B5
          inet6 addr: fe80::36ce:ff:fe6a:7fb5/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:128 errors:0 dropped:5 overruns:0 frame:0
          TX packets:9 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:24630 (24.0 KiB)  TX bytes:882 (882.0 B)
          Interrupt:20

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:65536  Metric:1
          RX packets:1072 errors:0 dropped:0 overruns:0 frame:0
          TX packets:1072 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:76528 (74.7 KiB)  TX bytes:76528 (74.7 KiB)

sidors85 · 2022-02-02 19:50:26

sidors85
Użytkownik
Nieaktywny

Zarejestrowany: 2022-02-02
Posty: 12

Odp: Xiaomi router 3G problem po update

jak mogę z konsoli włączyć wifi?

Cezary · 2022-02-02 19:54:04

Cezary
...
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2006-02-25
Posty: 117,012

Odp: Xiaomi router 3G problem po update

Już wiem. Coś zrobiłeś i nie został zaktualizowany kernel! Jedziesz na starym kernelu 4.14.77 w 21.02 masz 5.4.171 aktualnie.

Ponieważ nie uruchomisz ani sieci, ani wifi, ani usb - wgraj mu jeszcze raz cały system przez bootloader (np. 1 i initramfs) a później zrób sysupgrade właściwym obrazem.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

sidors85 · 2022-02-02 19:56:43

sidors85
Użytkownik
Nieaktywny

Zarejestrowany: 2022-02-02
Posty: 12

Odp: Xiaomi router 3G problem po update

użyłem do update rootfs0 i to był błąd.

powiedz jak mu coś teraz wgrać jak mam dostępna tylko konsole?

Cezary · 2022-02-02 19:57:43

Cezary
...
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2006-02-25
Posty: 117,012

Odp: Xiaomi router 3G problem po update

Napisałem - wgraj przez bootloader - opcja 1 w menu. Serwer tftp oczywiście musisz mieć.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

sidors85 · 2022-02-02 19:59:14

sidors85
Użytkownik
Nieaktywny

Zarejestrowany: 2022-02-02
Posty: 12

Odp: Xiaomi router 3G problem po update

testowałem wczoraj ale żeby to zrobić muszą się widzieć (client serwer)

miałem cały czas time out

Cezary · 2022-02-02 20:00:44

Cezary
...
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2006-02-25
Posty: 117,012

Odp: Xiaomi router 3G problem po update

firewall/antywirus na windowsie.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

sidors85 · 2022-02-02 20:01:55

sidors85
Użytkownik
Nieaktywny

Zarejestrowany: 2022-02-02
Posty: 12

Odp: Xiaomi router 3G problem po update

ok potestuje jeszcze dzisiaj i dam znać czy poszło, dzięki wielkie za pomoc!

sidors85 · 2022-02-03 00:02:39

sidors85
Użytkownik
Nieaktywny

Zarejestrowany: 2022-02-02
Posty: 12

Odp: Xiaomi router 3G problem po update

Hej, miałeś racje firewall blokował tftp po wgraniu na nowo kernela i sysupgrade wszystko śmiga jak trzeba.

dzieki za pomoc!

FAQ o OpenWrt | Sprzedam różne routery | Oddam

Xiaomi router 3G problem po update

Posty: 20

1 Temat przez sidors85 2022-02-02 17:41:32

Temat: Xiaomi router 3G problem po update

2 Odpowiedź przez Cezary 2022-02-02 17:44:09

Odp: Xiaomi router 3G problem po update

3 Odpowiedź przez sidors85 2022-02-02 19:19:03

Odp: Xiaomi router 3G problem po update

4 Odpowiedź przez Cezary 2022-02-02 19:22:13

Odp: Xiaomi router 3G problem po update

5 Odpowiedź przez sidors85 2022-02-02 19:28:11

Odp: Xiaomi router 3G problem po update

6 Odpowiedź przez Cezary 2022-02-02 19:33:53

Odp: Xiaomi router 3G problem po update

7 Odpowiedź przez sidors85 2022-02-02 19:35:02

Odp: Xiaomi router 3G problem po update

8 Odpowiedź przez Cezary 2022-02-02 19:35:48

Odp: Xiaomi router 3G problem po update

9 Odpowiedź przez sidors85 2022-02-02 19:41:33

Odp: Xiaomi router 3G problem po update

10 Odpowiedź przez sidors85 2022-02-02 19:43:07 (edytowany przez sidors85 2022-02-02 19:43:33)

Odp: Xiaomi router 3G problem po update

11 Odpowiedź przez Cezary 2022-02-02 19:44:25

Odp: Xiaomi router 3G problem po update

12 Odpowiedź przez sidors85 2022-02-02 19:47:53

Odp: Xiaomi router 3G problem po update

13 Odpowiedź przez sidors85 2022-02-02 19:50:26

Odp: Xiaomi router 3G problem po update

14 Odpowiedź przez Cezary 2022-02-02 19:54:04

Odp: Xiaomi router 3G problem po update

15 Odpowiedź przez sidors85 2022-02-02 19:56:43

Odp: Xiaomi router 3G problem po update

16 Odpowiedź przez Cezary 2022-02-02 19:57:43

Odp: Xiaomi router 3G problem po update

17 Odpowiedź przez sidors85 2022-02-02 19:59:14

Odp: Xiaomi router 3G problem po update

18 Odpowiedź przez Cezary 2022-02-02 20:00:44

Odp: Xiaomi router 3G problem po update

19 Odpowiedź przez sidors85 2022-02-02 20:01:55

Odp: Xiaomi router 3G problem po update

20 Odpowiedź przez sidors85 2022-02-03 00:02:39

Odp: Xiaomi router 3G problem po update

Posty: 20