1 (edytowany przez debiecm 2021-10-24 09:43:14)

Temat: ??? Device linksys,rango not supported by this image ???

Witajcie,
na moim WRT3200ACM mam obecnie LuCI (OpenWrt 19.07). Ściągnąłem LuCI OpenWrt 21.02 (luci-21.02-snapshot-r16295-3a051a234a-mvebu-cortexa9-linksys_wrt3200acm-squashfs-sysupgrade.bin) i przed wykonaniem aktualizacji mam taki komunikat:

Device linksys,rango not supported by this image Supported devices: linksys,wrt3200acm armada-385-linksys-rango linksys,rango - Image version mismatch: image 1.1, device 1.0. Please wipe config during upgrade (force required) or reinstall. Reason: Config cannot be migrated from swconfig to DSA Image check failed.

Przesłany plik obrazu nie zawiera obsługiwanego formatu. Upewnij się, że wybrałeś odpowiedni format obrazu dla danej platformy.


Czy mogę wykonać /wymusić aktualizację i nie uwalić router'a ?

2

Odp: ??? Device linksys,rango not supported by this image ???

Nawet Ci napisał dlaczego.

Możesz wymusić aktualizację, ale BEZ zachowywania konfiguracji. I później nie odtwarzaj starego backupu na tej wersji.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

3 (edytowany przez debiecm 2021-10-24 14:02:43)

Odp: ??? Device linksys,rango not supported by this image ???

Dziękuję za podpowiedź!

4

Odp: ??? Device linksys,rango not supported by this image ???

Koledzy,
niestety router działa tragicznie, WiFi wyłącza się samodzielnie po około 3 min od wlaczenia, do tego stopnia ze muszę go restartować prądowo.
Przywracam do wersji 19.07 i tutaj pytanie czy mogę wykonać downgrade plikiem sys-upgrade, ponieważ mam poniższe komunikaty:

Mon Oct 25 11:30:55 CEST 2021 upgrade: Device linksys,wrt3200acm not supported by this image Mon Oct 25 11:30:55 CEST 2021 upgrade: Supported devices: armada-385-linksys-rango linksys,rango Image check failed.
Przesłany plik obrazu nie zawiera obsługiwanego formatu. Upewnij się, że wybrałeś odpowiedni format obrazu dla danej platformy.

Sprawdzanie obrazu nie powiodło się:
Mon Oct 25 11:30:55 CEST 2021 upgrade: Device linksys,wrt3200acm not supported by this image Mon Oct 25 11:30:55 CEST 2021 upgrade: Supported devices: armada-385-linksys-rango linksys,rango Image check failed.

5

Odp: ??? Device linksys,rango not supported by this image ???

Dokładnie ta sama odpowiedź co poprzednio - tak, możesz, bez zachowania konfiguracji, bez odtwarzania backupu.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

6

Odp: ??? Device linksys,rango not supported by this image ???

Thx!

7

Odp: ??? Device linksys,rango not supported by this image ???

Zgłupialem...!

Po przywróceniu Luci 19.07 i przywróceniu konfigu, radio 5GHZ pomimo że jest włączone nie nadaje. Restart interfejsu, włączeni i wyłączenie nic nie daje.

W czym może być problem?

8

Odp: ??? Device linksys,rango not supported by this image ???

Ok, a jesteś pewien że nie pada Ci sprzęt po prostu?

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

9

Odp: ??? Device linksys,rango not supported by this image ???

Wydaje mi się że nie choć wszystko jest możliwe. Dobra mam punkt zaczepienia, mam 3 radia:
1. radio0 - i tutaj mam wykonany konfig dla 5Ghz
2. radio1 - konfig dla 2,4Ghz i działa
3. radio2 - wyłączone, konfig default SSID openwrt

Jak włączę radio2 to rozgłąsza ten SSID ale nie mój z radio0.

10

Odp: ??? Device linksys,rango not supported by this image ???

Wyłącz to trzecie radio bo tylko problemy robi.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

11 (edytowany przez debiecm 2021-10-25 11:05:52)

Odp: ??? Device linksys,rango not supported by this image ???

No wlasnie jest wylaczone a radio0 nie dziala. Najciekawsze ze nic nie zmienialem, tylko przywrocilem stary soft i konfig ktory zrzuciłem przed wgraniem nowego 21.02.

12

Odp: ??? Device linksys,rango not supported by this image ???

Zrobie test, przywroce oryginalny soft Linksys, i zobacze czy nadaje na 5Ghz. Nastepnie podstawie znowu OpenWrt.
1. czy oryginalny soft mam przywrocic przez "Wgraj nowy obraz firmware" ?
2. czy OpenWrt mam zgrac na oryginalny soft plikiem "factory" ?

13

Odp: ??? Device linksys,rango not supported by this image ???

https://openwrt.org/toh/linksys/wrt3200acm

1. Tak, bez zachowywania konfiguracji i z wymuszeniem
2. Tak

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

14 (edytowany przez debiecm 2021-10-28 14:43:29)

Odp: ??? Device linksys,rango not supported by this image ???

Witajcie,
na oryginalnym firmware Linksys oba radia działają poprawnie - zatem nie wskazuje to na usterkę sprzętu. Po nadpisaniu ponownie na Luci 21.02, problem dalej ten sam - radio 5G nie działa.

Zmieniłem contry code na PL i to samo.
Pomoże ktoś? Poniżej zrzut z /etc/config/wireless; iw dev; iw list


config wifi-device 'radio0'
    option type 'mac80211'
    option hwmode '11a'
    option path 'soc/soc:pcie/pci0000:00/0000:00:01.0/0000:01:00.0'
    option country 'PL'
    option cell_density '0'
    option htmode 'VHT160'
    option channel '108'

config wifi-iface 'default_radio0'
    option device 'radio0'
    option network 'lan'
    option mode 'ap'
    option macaddr 'XX:XX:XX:XX:XX:XX'
    option ssid 'Debcu'
    option macfilter 'allow'
    list maclist 'XX:XX:XX:XX:XX:XX'
    option key 'XXX'
    option encryption 'psk2'
config wifi-device 'radio1'
    option type 'mac80211'
    option hwmode '11g'
    option path 'soc/soc:pcie/pci0000:00/0000:00:02.0/0000:02:00.0'
    option country 'PL'
    option htmode 'HT40'
    option channel '13'
    option cell_density '0'
config wifi-iface 'default_radio1'
    option device 'radio1'
    option network 'lan'
    option mode 'ap'
    option macaddr 'XX:XX:XX:XX:XX:XX'
    option ssid 'Debcu_2,4GHz'
    option macfilter 'allow'
    list maclist 'XX:XX:XX:XX:XX:XX'
    option encryption 'psk2'
    option key 'XXX'
config wifi-device 'radio2'
    option type 'mac80211'
    option channel '34'
    option hwmode '11a'
    option path 'platform/soc/soc:internal-regs/f10d8000.sdhci/mmc_host/mmc0/mmc0:0001/mmc0:0001:1'
    option htmode 'VHT80'
    option country 'PL'
    option disabled '0'
config wifi-iface 'default_radio2'
    option device 'radio2'
    option network 'lan'
    option mode 'ap'
    option ssid 'OpenWrt'
    option encryption 'none'







iw dev

phy#2
        Interface wlan2
                ifindex 14
                wdev 0x200000001
                addr 60:38:e0:bc:2d:e3
                type AP
                txpower 0.00 dBm
phy#1
        Interface wlan1
                ifindex 13
                wdev 0x100000002
                addr 60:38:e0:bc:2d:e1
                ssid Debcu_2,4GHz
                type AP
                channel 13 (2472 MHz), width: 20 MHz, center1: 2472 MHz
                txpower 20.00 dBm
phy#0
        Interface wlan0
                ifindex 12
                wdev 0x2
                addr 60:38:e0:bc:2d:e2
                type AP
                txpower 23.00 dBm






iw list

Wiphy phy2
        wiphy index: 2
        max # scan SSIDs: 10
        max scan IEs length: 256 bytes
        max # sched scan SSIDs: 10
        max # match sets: 10
        Fragmentation threshold: 2346
        RTS threshold: 2347
        Retry short limit: 9
        Retry long limit: 4
        Coverage class: 0 (up to 0m)
        Device supports AP-side u-APSD.
        Device supports T-DLS.
        Available Antennas: TX 0x1 RX 0x1
        Configured Antennas: TX 0x1 RX 0x1
        Supported interface modes:
                 * managed
                 * AP
                 * P2P-client
                 * P2P-GO
        Band 1:
                Capabilities: 0x17f
                        RX LDPC
                        HT20/HT40
                        SM Power Save disabled
                        RX Greenfield
                        RX HT20 SGI
                        RX HT40 SGI
                        RX STBC 1-stream
                        Max AMSDU length: 3839 bytes
                        No DSSS/CCK HT40
                Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
                Minimum RX AMPDU time spacing: No restriction (0x00)
                HT TX/RX MCS rate indexes supported: 0-7, 32
                VHT Capabilities (0x33c07130):
                        Max MPDU length: 3895
                        Supported Channel Width: neither 160 nor 80+80
                        RX LDPC
                        short GI (80 MHz)
                        SU Beamformee
                        +HTC-VHT
                        RX antenna pattern consistency
                        TX antenna pattern consistency
                VHT RX MCS set:
                        1 streams: MCS 0-9
                        2 streams: not supported
                        3 streams: not supported
                        4 streams: not supported
                        5 streams: not supported
                        6 streams: not supported
                        7 streams: not supported
                        8 streams: not supported
                VHT RX highest supported: 0 Mbps
                VHT TX MCS set:
                        1 streams: MCS 0-9
                        2 streams: not supported
                        3 streams: not supported
                        4 streams: not supported
                        5 streams: not supported
                        6 streams: not supported
                        7 streams: not supported
                        8 streams: not supported
                VHT TX highest supported: 0 Mbps
                Frequencies:
                        * 2412 MHz [1] (30.0 dBm)
                        * 2417 MHz [2] (30.0 dBm)
                        * 2422 MHz [3] (30.0 dBm)
                        * 2427 MHz [4] (30.0 dBm)
                        * 2432 MHz [5] (30.0 dBm)
                        * 2437 MHz [6] (30.0 dBm)
                        * 2442 MHz [7] (30.0 dBm)
                        * 2447 MHz [8] (30.0 dBm)
                        * 2452 MHz [9] (30.0 dBm)
                        * 2457 MHz [10] (30.0 dBm)
                        * 2462 MHz [11] (30.0 dBm)
                        * 2467 MHz [12] (disabled)
                        * 2472 MHz [13] (disabled)
                        * 2484 MHz [14] (disabled)
        Band 2:
                Capabilities: 0x17f
                        RX LDPC
                        HT20/HT40
                        SM Power Save disabled
                        RX Greenfield
                        RX HT20 SGI
                        RX HT40 SGI
                        RX STBC 1-stream
                        Max AMSDU length: 3839 bytes
                        No DSSS/CCK HT40
                Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
                Minimum RX AMPDU time spacing: No restriction (0x00)
                HT TX/RX MCS rate indexes supported: 0-7, 32
                VHT Capabilities (0x33c07130):
                        Max MPDU length: 3895
                        Supported Channel Width: neither 160 nor 80+80
                        RX LDPC
                        short GI (80 MHz)
                        SU Beamformee
                        +HTC-VHT
                        RX antenna pattern consistency
                        TX antenna pattern consistency
                VHT RX MCS set:
                        1 streams: MCS 0-9
                        2 streams: not supported
                        3 streams: not supported
                        4 streams: not supported
                        5 streams: not supported
                        6 streams: not supported
                        7 streams: not supported
                        8 streams: not supported
                VHT RX highest supported: 0 Mbps
                VHT TX MCS set:
                        1 streams: MCS 0-9
                        2 streams: not supported
                        3 streams: not supported
                        4 streams: not supported
                        5 streams: not supported
                        6 streams: not supported
                        7 streams: not supported
                        8 streams: not supported
                VHT TX highest supported: 0 Mbps
                Frequencies:
                        * 5040 MHz [8] (disabled)
                        * 5060 MHz [12] (disabled)
                        * 5080 MHz [16] (disabled)
                        * 5170 MHz [34] (23.0 dBm)
                        * 5190 MHz [38] (23.0 dBm)
                        * 5210 MHz [42] (23.0 dBm)
                        * 5230 MHz [46] (23.0 dBm)
                        * 5180 MHz [36] (23.0 dBm)
                        * 5200 MHz [40] (23.0 dBm)
                        * 5220 MHz [44] (23.0 dBm)
                        * 5240 MHz [48] (23.0 dBm)
                        * 5260 MHz [52] (23.0 dBm) (no IR, radar detection)
                        * 5280 MHz [56] (23.0 dBm) (no IR, radar detection)
                        * 5300 MHz [60] (23.0 dBm) (no IR, radar detection)
                        * 5320 MHz [64] (23.0 dBm) (no IR, radar detection)
                        * 5500 MHz [100] (23.0 dBm) (no IR, radar detection)
                        * 5520 MHz [104] (23.0 dBm) (no IR, radar detection)
                        * 5540 MHz [108] (23.0 dBm) (no IR, radar detection)
                        * 5560 MHz [112] (23.0 dBm) (no IR, radar detection)
                        * 5580 MHz [116] (23.0 dBm) (no IR, radar detection)
                        * 5600 MHz [120] (23.0 dBm) (no IR, radar detection)
                        * 5620 MHz [124] (23.0 dBm) (no IR, radar detection)
                        * 5640 MHz [128] (23.0 dBm) (no IR, radar detection)
                        * 5660 MHz [132] (23.0 dBm) (no IR, radar detection)
                        * 5680 MHz [136] (23.0 dBm) (no IR, radar detection)
                        * 5700 MHz [140] (23.0 dBm) (no IR, radar detection)
                        * 5745 MHz [149] (30.0 dBm)
                        * 5765 MHz [153] (30.0 dBm)
                        * 5785 MHz [157] (30.0 dBm)
                        * 5805 MHz [161] (30.0 dBm)
                        * 5825 MHz [165] (30.0 dBm)
        valid interface combinations:
                 * #{ managed, AP, P2P-client, P2P-GO } <= 3,
                   total <= 3, #channels <= 1, STA/AP BI must match, radar detect widths: { 20 MHz (no HT), 20 MHz, 40 MHz, 80 MHz }

        max # scan plans: 1
        max scan plan interval: -1
        max scan plan iterations: 0
        Coalesce support:
                 * Maximum 8 coalesce rules supported
                 * Each rule contains upto 4 patterns of 1-40 bytes,
                   maximum packet offset 100 bytes
                 * Maximum supported coalescing delay 100 msecs
        Supported extended features:
Wiphy phy1
        wiphy index: 1
        max # scan SSIDs: 4
        max scan IEs length: 2242 bytes
        max # sched scan SSIDs: 0
        max # match sets: 0
        Retry short limit: 7
        Retry long limit: 4
        Coverage class: 0 (up to 0m)
        Device supports AP-side u-APSD.
        Device supports T-DLS.
        Available Antennas: TX 0 RX 0
        Supported interface modes:
                 * managed
                 * AP
                 * AP/VLAN
                 * monitor
                 * mesh point
        Band 1:
                Capabilities: 0x186f
                        RX LDPC
                        HT20/HT40
                        SM Power Save disabled
                        RX HT20 SGI
                        RX HT40 SGI
                        No RX STBC
                        Max AMSDU length: 7935 bytes
                        DSSS/CCK HT40
                Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
                Minimum RX AMPDU time spacing: 4 usec (0x05)
                HT TX/RX MCS rate indexes supported: 0-23, 32
                VHT Capabilities (0x339b7976):
                        Max MPDU length: 11454
                        Supported Channel Width: 160 MHz
                        RX LDPC
                        short GI (80 MHz)
                        short GI (160/80+80 MHz)
                        SU Beamformer
                        SU Beamformee
                        MU Beamformer
                        MU Beamformee
                        RX antenna pattern consistency
                        TX antenna pattern consistency
                VHT RX MCS set:
                        1 streams: MCS 0-9
                        2 streams: MCS 0-9
                        3 streams: MCS 0-9
                        4 streams: not supported
                        5 streams: not supported
                        6 streams: not supported
                        7 streams: not supported
                        8 streams: not supported
                VHT RX highest supported: 0 Mbps
                VHT TX MCS set:
                        1 streams: MCS 0-9
                        2 streams: MCS 0-9
                        3 streams: MCS 0-9
                        4 streams: not supported
                        5 streams: not supported
                        6 streams: not supported
                        7 streams: not supported
                        8 streams: not supported
                VHT TX highest supported: 0 Mbps
                Frequencies:
                        * 2412 MHz [1] (20.0 dBm)
                        * 2417 MHz [2] (20.0 dBm)
                        * 2422 MHz [3] (20.0 dBm)
                        * 2427 MHz [4] (20.0 dBm)
                        * 2432 MHz [5] (20.0 dBm)
                        * 2437 MHz [6] (20.0 dBm)
                        * 2442 MHz [7] (20.0 dBm)
                        * 2447 MHz [8] (20.0 dBm)
                        * 2452 MHz [9] (20.0 dBm)
                        * 2457 MHz [10] (20.0 dBm)
                        * 2462 MHz [11] (20.0 dBm)
                        * 2467 MHz [12] (20.0 dBm)
                        * 2472 MHz [13] (20.0 dBm)
                        * 2484 MHz [14] (disabled)
        valid interface combinations:
                 * #{ AP } <= 16, #{ mesh point } <= 1, #{ managed } <= 1,
                   total <= 16, #channels <= 1, radar detect widths: { 20 MHz (no HT), 20 MHz, 40 MHz, 80 MHz, 160 MHz }

        HT Capability overrides:
                 * MCS: ff ff ff ff ff ff ff ff ff ff
                 * maximum A-MSDU length
                 * supported channel width
                 * short GI for 40 MHz
                 * max A-MPDU length exponent
                 * min MPDU start spacing
        max # scan plans: 1
        max scan plan interval: -1
        max scan plan iterations: 0
        Supported extended features:
                * [ RRM ]: RRM
                * [ CONTROL_PORT_OVER_NL80211 ]: control port over nl80211
                * [ SCAN_RANDOM_SN ]: use random sequence numbers in scans
                * [ SCAN_MIN_PREQ_CONTENT ]: use probe request with only rate IEs in scans
                * [ CONTROL_PORT_NO_PREAUTH ]: disable pre-auth over nl80211 control port support
                * [ SCAN_FREQ_KHZ ]: scan on kHz frequency support
                * [ CONTROL_PORT_OVER_NL80211_TX_STATUS ]: tx status for nl80211 control port support
Wiphy phy0
        wiphy index: 0
        max # scan SSIDs: 4
        max scan IEs length: 2247 bytes
        max # sched scan SSIDs: 0
        max # match sets: 0
        Retry short limit: 7
        Retry long limit: 4
        Coverage class: 0 (up to 0m)
        Device supports AP-side u-APSD.
        Device supports T-DLS.
        Available Antennas: TX 0 RX 0
        Supported interface modes:
                 * managed
                 * AP
                 * AP/VLAN
                 * monitor
                 * mesh point
        Band 2:
                Capabilities: 0x186f
                        RX LDPC
                        HT20/HT40
                        SM Power Save disabled
                        RX HT20 SGI
                        RX HT40 SGI
                        No RX STBC
                        Max AMSDU length: 7935 bytes
                        DSSS/CCK HT40
                Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
                Minimum RX AMPDU time spacing: 4 usec (0x05)
                HT TX/RX MCS rate indexes supported: 0-23, 32
                VHT Capabilities (0x339b7976):
                        Max MPDU length: 11454
                        Supported Channel Width: 160 MHz
                        RX LDPC
                        short GI (80 MHz)
                        short GI (160/80+80 MHz)
                        SU Beamformer
                        SU Beamformee
                        MU Beamformer
                        MU Beamformee
                        RX antenna pattern consistency
                        TX antenna pattern consistency
                VHT RX MCS set:
                        1 streams: MCS 0-9
                        2 streams: MCS 0-9
                        3 streams: MCS 0-9
                        4 streams: not supported
                        5 streams: not supported
                        6 streams: not supported
                        7 streams: not supported
                        8 streams: not supported
                VHT RX highest supported: 0 Mbps
                VHT TX MCS set:
                        1 streams: MCS 0-9
                        2 streams: MCS 0-9
                        3 streams: MCS 0-9
                        4 streams: not supported
                        5 streams: not supported
                        6 streams: not supported
                        7 streams: not supported
                        8 streams: not supported
                VHT TX highest supported: 0 Mbps
                Frequencies:
                        * 5180 MHz [36] (23.0 dBm)
                        * 5200 MHz [40] (23.0 dBm)
                        * 5220 MHz [44] (23.0 dBm)
                        * 5240 MHz [48] (23.0 dBm)
                        * 5260 MHz [52] (20.0 dBm) (radar detection)
                        * 5280 MHz [56] (20.0 dBm) (radar detection)
                        * 5300 MHz [60] (20.0 dBm) (radar detection)
                        * 5320 MHz [64] (20.0 dBm) (radar detection)
                        * 5500 MHz [100] (26.0 dBm) (radar detection)
                        * 5520 MHz [104] (26.0 dBm) (radar detection)
                        * 5540 MHz [108] (26.0 dBm) (radar detection)
                        * 5560 MHz [112] (26.0 dBm) (radar detection)
                        * 5580 MHz [116] (26.0 dBm) (radar detection)
                        * 5600 MHz [120] (26.0 dBm) (radar detection)
                        * 5620 MHz [124] (26.0 dBm) (radar detection)
                        * 5640 MHz [128] (26.0 dBm) (radar detection)
                        * 5660 MHz [132] (26.0 dBm) (radar detection)
                        * 5680 MHz [136] (26.0 dBm) (radar detection)
                        * 5700 MHz [140] (26.0 dBm) (radar detection)
                        * 5720 MHz [144] (13.0 dBm) (radar detection)
                        * 5745 MHz [149] (13.0 dBm)
                        * 5765 MHz [153] (13.0 dBm)
                        * 5785 MHz [157] (13.0 dBm)
                        * 5805 MHz [161] (13.0 dBm)
        valid interface combinations:
                 * #{ AP } <= 16, #{ mesh point } <= 1, #{ managed } <= 1,
                   total <= 16, #channels <= 1, radar detect widths: { 20 MHz (no HT), 20 MHz, 40 MHz, 80 MHz, 160 MHz }

        HT Capability overrides:
                 * MCS: ff ff ff ff ff ff ff ff ff ff
                 * maximum A-MSDU length
                 * supported channel width
                 * short GI for 40 MHz
                 * max A-MPDU length exponent
                 * min MPDU start spacing
        max # scan plans: 1
        max scan plan interval: -1
        max scan plan iterations: 0
        Supported extended features:
                * [ RRM ]: RRM
                * [ CONTROL_PORT_OVER_NL80211 ]: control port over nl80211
                * [ SCAN_RANDOM_SN ]: use random sequence numbers in scans
                * [ SCAN_MIN_PREQ_CONTENT ]: use probe request with only rate IEs in scans
                * [ CONTROL_PORT_NO_PREAUTH ]: disable pre-auth over nl80211 control port support
                * [ SCAN_FREQ_KHZ ]: scan on kHz frequency support
                * [ CONTROL_PORT_OVER_NL80211_TX_STATUS ]: tx status for nl80211 control port support

15

Odp: ??? Device linksys,rango not supported by this image ???

Nie zmieniaj country na pl, zostaw tak jak było. Firmware linksysa rozpoznaje tylko kilka regionów i nie jest to PL.

Usuń VHT160, ustaw VHT80 i zmień kanał na 36

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

16 (edytowany przez debiecm 2021-10-28 15:54:19)

Odp: ??? Device linksys,rango not supported by this image ???

Cezary napisał/a:

Nie zmieniaj country na pl, zostaw tak jak było. Firmware linksysa rozpoznaje tylko kilka regionów i nie jest to PL.

Usuń VHT160, ustaw VHT80 i zmień kanał na 36


@Cezary, jak zawsze porządna firma wink! - 5GHz wstało po zmianach. Dziękuję!
Czy wyłączyć również radio2 ?


config wifi-device 'radio0'
    option type 'mac80211'
    option hwmode '11a'
    option path 'soc/soc:pcie/pci0000:00/0000:00:01.0/0000:01:00.0'
    option country 'FR'
    option cell_density '0'
    option htmode 'VHT80'
    option channel '36'

config wifi-iface 'default_radio0'
    option device 'radio0'
    option network 'lan'
    option mode 'ap'
    option macaddr 'XX:XX:XX:XX:XX:XX'
    option ssid 'Debcu'
    option macfilter 'allow'
    list maclist 'XX:XX:XX:XX:XX:XX'
    option key 'XXX'
    option encryption 'psk2'

config wifi-device 'radio1'
    option type 'mac80211'
    option hwmode '11g'
    option path 'soc/soc:pcie/pci0000:00/0000:00:02.0/0000:02:00.0'
    option country 'FR'
    option htmode 'HT40'
    option channel '13'
    option cell_density '0'

config wifi-iface 'default_radio1'
    option device 'radio1'
    option network 'lan'
    option mode 'ap'
    option macaddr 'XX:XX:XX:XX:XX:XX'
    option ssid 'Debcu_2,4GHz'
    option macfilter 'allow'
    list maclist 'XX:XX:XX:XX:XX:XX'
    option encryption 'psk2'
    option key 'XXX'

config wifi-device 'radio2'
    option type 'mac80211'
    option channel '34'
    option hwmode '11a'
    option path 'platform/soc/soc:internal-regs/f10d8000.sdhci/mmc_host/mmc0/mmc0:0001/mmc0:0001:1'
    option htmode 'VHT80'
    option country 'FR'
    option disabled '0'

config wifi-iface 'default_radio2'
    option device 'radio2'
    option network 'lan'
    option mode 'ap'
    option ssid 'OpenWrt'
    option encryption 'none'

17

Odp: ??? Device linksys,rango not supported by this image ???

Jak chcesz, ale generalnie radio2 jakieś tam problemy sprawiało.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.