Booting System 2

..Erasing NAND Flash...

ranand_erase: start:80000, len:20000 

.Writing to NAND Flash...

done

   

3: System Boot system code via Flash.

## Booting image at bc600000 ...

   Image Name:   MIPS OpenWrt Linux-5.4.137

   Image Type:   MIPS Linux Kernel Image (uncompressed)

   Data Size:    2366085 Bytes =  2.3 MB

   Load Address: 80001000

   Entry Point:  80001000

.....................................   Verifying Checksum ... OK

OK

commandline uart_en=0 factory_mode=0 usb_u3=0

No initrd

## Transferring control to Linux (at address 80001000) ...

## Giving linux memsize in MB, 256


Starting kernel ...




OpenWrt kernel loader for MIPS based SoC

Copyright (C) 2011 Gabor Juhos <juhosg@openwrt.org>

Decompressing kernel... done!

Starting kernel at 80001000...


[    0.000000] Linux version 5.4.137 (cezary@eko.one.pl) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r15819-0011c7ad12)) #0 SMP Mon Aug 2 20:42:46 2021
[    0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
[    0.000000] printk: bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[    0.000000] MIPS: machine is Xiaomi Mi Router 3G
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] VPE topology {2,2} total 4
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x000000000fffffff]
[    0.000000]   HighMem  empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x000000000fffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff]
[    0.000000] percpu: Embedded 14 pages/cpu s26768 r8192 d22384 u57344
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 64960
[    0.000000] Kernel command line: console=ttyS0,115200n8 rootfstype=squashfs,jffs2
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[    0.000000] Writing ErrCtl register=0000043e
[    0.000000] Readback ErrCtl register=0000043e
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 250788K/262144K available (6085K kernel code, 206K rwdata, 748K rodata, 1268K init, 238K bss, 11356K reserved, 0K cma-reserved, 0K highmem)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] rcu: Hierarchical RCU implementation.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[    0.000000] NR_IRQS: 256
[    0.000000] random: get_random_bytes called from 0x806e3a3c with crng_init=0
[    0.000000] CPU Clock: 880MHz
[    0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns
[    0.000009] sched_clock: 32 bits at 440MHz, resolution 2ns, wraps every 4880645118ns
[    0.007817] Calibrating delay loop... 583.68 BogoMIPS (lpj=1167360)
[    0.042013] pid_max: default: 32768 minimum: 301
[    0.046790] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.054016] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.064509] rcu: Hierarchical SRCU implementation.
[    0.069968] smp: Bringing up secondary CPUs ...
[    7.311930] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    7.311940] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    7.311952] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[    7.312058] CPU1 revision is: 0001992f (MIPS 1004Kc)
[    0.102739] Synchronize counters for CPU 1: done.
[    7.373573] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    7.373582] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    7.373590] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[    7.373648] CPU2 revision is: 0001992f (MIPS 1004Kc)
[    0.167461] Synchronize counters for CPU 2: done.
[    7.434647] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    7.434655] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    7.434664] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[    7.434726] CPU3 revision is: 0001992f (MIPS 1004Kc)
[    0.225322] Synchronize counters for CPU 3: done.
[    0.255200] smp: Brought up 1 node, 4 CPUs
[    0.263833] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.273523] futex hash table entries: 1024 (order: 3, 32768 bytes, linear)
[    0.280602] pinctrl core: initialized pinctrl subsystem
[    0.287532] NET: Registered protocol family 16
[    0.315451] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512
[    0.326683] clocksource: Switched to clocksource GIC
[    0.333297] thermal_sys: Registered thermal governor 'step_wise'
[    0.333814] NET: Registered protocol family 2
[    0.344344] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear)
[    0.352527] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[    0.360912] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear)
[    0.368509] TCP bind hash table entries: 2048 (order: 2, 16384 bytes, linear)
[    0.375598] TCP: Hash tables configured (established 2048 bind 2048)
[    0.382020] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.388498] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.395694] NET: Registered protocol family 1
[    0.400014] PCI: CLS 0 bytes, default 32
[    0.494626] 4 CPUs re-calibrate udelay(lpj = 1163264)
[    0.501259] workingset: timestamp_bits=14 max_order=16 bucket_order=2
[    0.507852] random: fast init done
[    0.523205] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.528974] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.540529] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[    0.549764] mt7621_gpio 1e000600.gpio: registering 32 gpios
[    0.555759] mt7621_gpio 1e000600.gpio: registering 32 gpios
[    0.561604] mt7621_gpio 1e000600.gpio: registering 32 gpios
[    0.568075] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.578197] printk: console [ttyS0] disabled
[    0.582510] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 19, base_baud = 3125000) is a 16550A
[    0.591501] printk: console [ttyS0] enabled
[    0.591501] printk: console [ttyS0] enabled
[    0.599761] printk: bootconsole [early0] disabled
[    0.599761] printk: bootconsole [early0] disabled
[    0.611850] mt7621-nand 1e003000.nand: Using programmed access timing: 31c07388
[    0.619261] nand: device found, Manufacturer ID: 0xc8, Chip ID: 0xd1
[    0.625609] nand: ESMT NAND 128MiB 3,3V 8-bit
[    0.629964] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    0.637526] mt7621-nand 1e003000.nand: ECC strength adjusted to 4 bits
[    0.644074] mt7621-nand 1e003000.nand: Using programmed access timing: 31c07388
[    0.651373] Scanning device for bad blocks
[    2.764069] 10 fixed-partitions partitions found on MTD device mt7621-nand
[    2.770936] Creating 10 MTD partitions on "mt7621-nand":
[    2.776255] 0x000000000000-0x000000080000 : "Bootloader"
[    2.783090] 0x000000080000-0x0000000c0000 : "Config"
[    2.789525] 0x0000000c0000-0x000000100000 : "Bdata"
[    2.795791] 0x000000100000-0x000000140000 : "factory"
[    2.802311] 0x000000140000-0x000000180000 : "crash"
[    2.808572] 0x000000180000-0x0000001c0000 : "crash_syslog"
[    2.815617] 0x0000001c0000-0x000000200000 : "reserved0"
[    2.822216] 0x000000200000-0x000000600000 : "kernel_stock"
[    2.829198] 0x000000600000-0x000000a00000 : "kernel"
[    2.835620] 0x000000a00000-0x000007f80000 : "ubi"
[    2.844009] libphy: Fixed MDIO Bus: probed
[    2.873042] libphy: mdio: probed
[    2.876514] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module
[    2.886942] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 21
[    2.897507] mt7621-pci 1e140000.pcie: Parsing DT failed
[    2.905428] NET: Registered protocol family 10
[    2.911465] Segment Routing with IPv6
[    2.915320] NET: Registered protocol family 17
[    2.919874] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    2.933107] 8021q: 802.1Q VLAN Support v1.8
[    2.939981] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module
[    2.957169] libphy: dsa slave smi: probed
[    2.961810] mt7530 mdio-bus:1f wan (uninitialized): PHY [dsa-0.0:01] driver [Generic PHY]
[    2.971561] mt7530 mdio-bus:1f lan2 (uninitialized): PHY [dsa-0.0:02] driver [Generic PHY]
[    2.981341] mt7530 mdio-bus:1f lan1 (uninitialized): PHY [dsa-0.0:03] driver [Generic PHY]
[    2.991409] mt7530 mdio-bus:1f: configuring for fixed/rgmii link mode
[    3.002666] DSA: tree 0 setup
[    3.005948] rt2880-pinmux pinctrl: pcie is already enabled
[    3.011581] mt7621-pci-phy 1e149000.pcie-phy: PHY for 0xbe149000 (dual port = 1)
[    3.019186] mt7621-pci-phy 1e14a000.pcie-phy: PHY for 0xbe14a000 (dual port = 0)
[    3.126434] mt7621-pci-phy 1e149000.pcie-phy: Xtal is 40MHz
[    3.132022] mt7621-pci-phy 1e14a000.pcie-phy: Xtal is 40MHz
[    3.237360] mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK)
[    3.244315] mt7621-pci 1e140000.pcie: PCIE0 enabled
[    3.249193] mt7621-pci 1e140000.pcie: PCIE1 enabled
[    3.254072] mt7621-pci 1e140000.pcie: PCI coherence region base: 0x60000000, mask/settings: 0xf0000002
[    3.263537] mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00
[    3.269906] pci_bus 0000:00: root bus resource [io  0x1e160000-0x1e16ffff]
[    3.276775] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
[    3.283645] pci_bus 0000:00: root bus resource [bus 00-ff]
[    3.289171] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400
[    3.295209] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[    3.301483] pci 0000:00:00.0: reg 0x14: [mem 0x00000000-0x0000ffff]
[    3.307817] pci 0000:00:00.0: supports D1
[    3.311832] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[    3.317958] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400
[    3.324009] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[    3.330278] pci 0000:00:01.0: reg 0x14: [mem 0x00000000-0x0000ffff]
[    3.336605] pci 0000:00:01.0: supports D1
[    3.340619] pci 0000:00:01.0: PME# supported from D0 D1 D3hot
[    3.347803] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    3.355811] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    3.364010] pci 0000:01:00.0: [14c3:7603] type 00 class 0x028000
[    3.370068] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff]
[    3.376469] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[    3.384000] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[    3.389244] pci 0000:00:00.0:   bridge window [io  0x0000-0x0fff]
[    3.395334] pci 0000:00:00.0:   bridge window [mem 0x00000000-0x000fffff]
[    3.402118] pci 0000:00:00.0:   bridge window [mem 0x00000000-0x000fffff pref]
[    3.409336] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[    3.416173] pci 0000:02:00.0: [14c3:7662] type 00 class 0x028000
[    3.422240] pci 0000:02:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit]
[    3.429068] pci 0000:02:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[    3.435867] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
[    3.443413] pci 0000:00:01.0: PCI bridge to [bus 02-ff]
[    3.448648] pci 0000:00:01.0:   bridge window [io  0x0000-0x0fff]
[    3.454739] pci 0000:00:01.0:   bridge window [mem 0x00000000-0x000fffff]
[    3.461520] pci 0000:00:01.0:   bridge window [mem 0x00000000-0x000fffff pref]
[    3.468737] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
[    3.475397] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[    3.482007] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[    3.488963] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000]
[    3.495571] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000]
[    3.502529] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
[    3.509313] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x601fffff pref]
[    3.516530] pci 0000:00:01.0: BAR 8: assigned [mem 0x60200000-0x602fffff]
[    3.523317] pci 0000:00:01.0: BAR 9: assigned [mem 0x60300000-0x603fffff pref]
[    3.530535] pci 0000:00:00.0: BAR 1: assigned [mem 0x60400000-0x6040ffff]
[    3.537323] pci 0000:00:01.0: BAR 1: assigned [mem 0x60410000-0x6041ffff]
[    3.544110] pci 0000:00:00.0: BAR 7: assigned [io  0x1e160000-0x1e160fff]
[    3.550895] pci 0000:00:01.0: BAR 7: assigned [io  0x1e161000-0x1e161fff]
[    3.557693] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff]
[    3.564478] pci 0000:00:00.0: PCI bridge to [bus 01]
[    3.569445] pci 0000:00:00.0:   bridge window [io  0x1e160000-0x1e160fff]
[    3.576227] pci 0000:00:00.0:   bridge window [mem 0x60000000-0x600fffff]
[    3.583011] pci 0000:00:00.0:   bridge window [mem 0x60100000-0x601fffff pref]
[    3.590235] pci 0000:02:00.0: BAR 0: assigned [mem 0x60200000-0x602fffff 64bit]
[    3.597548] pci 0000:02:00.0: BAR 6: assigned [mem 0x60300000-0x6030ffff pref]
[    3.604762] pci 0000:00:01.0: PCI bridge to [bus 02]
[    3.609730] pci 0000:00:01.0:   bridge window [io  0x1e161000-0x1e161fff]
[    3.616512] pci 0000:00:01.0:   bridge window [mem 0x60200000-0x602fffff]
[    3.623294] pci 0000:00:01.0:   bridge window [mem 0x60300000-0x603fffff pref]
[    3.631099] mt7530 mdio-bus:1f: Link is Up - 1Gbps/Full - flow control off
[    3.632288] UBI: auto-attach mtd9
[    3.641338] ubi0: attaching mtd9
[    4.936909] ubi0: scanning is finished
[    4.959195] ubi0: attached mtd9 (name "ubi", size 117 MiB)
[    4.964708] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    4.971576] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    4.978353] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[    4.985300] ubi0: good PEBs: 940, bad PEBs: 0, corrupted PEBs: 0
[    4.991300] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[    4.998512] ubi0: max/mean erase counter: 237/143, WL threshold: 4096, image sequence number: 1109835025
[    5.007971] ubi0: available PEBs: 0, total reserved PEBs: 940, PEBs reserved for bad PEB handling: 20
[    5.017194] ubi0: background thread "ubi_bgt0d" started, PID 490
[    5.019224] block ubiblock0_0: created from ubi0:0(rootfs)
[    5.028690] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
[    5.035648] hctosys: unable to open rtc device (rtc0)
[    5.049003] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[    5.060520] Freeing unused kernel memory: 1268K
[    5.065103] This architecture does not have kernel memory protection.
[    5.071533] Run /sbin/init as init process
[    5.660383] init: Console is alive
[    5.664053] init: - watchdog -
[    7.433222] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    7.491974] usbcore: registered new interface driver usbfs
[    7.497642] usbcore: registered new interface driver hub
[    7.503102] usbcore: registered new device driver usb
[    7.552003] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    7.565187] SCSI subsystem initialized
[    7.572796] ehci-fsl: Freescale EHCI Host controller driver
[    7.579779] ehci-platform: EHCI generic platform driver
[    7.593976] xhci-mtk 1e1c0000.xhci: 1e1c0000.xhci supply vusb33 not found, using dummy regulator
[    7.603017] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
[    7.608365] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 1
[    7.622836] xhci-mtk 1e1c0000.xhci: hcc params 0x01401198 hci version 0x96 quirks 0x0000000000290010
[    7.632058] xhci-mtk 1e1c0000.xhci: irq 20, io mem 0x1e1c0000
[    7.639171] hub 1-0:1.0: USB hub found
[    7.643051] hub 1-0:1.0: 2 ports detected
[    7.647773] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
[    7.653117] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 2
[    7.660609] xhci-mtk 1e1c0000.xhci: Host supports USB 3.0 SuperSpeed
[    7.667168] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[    7.676153] hub 2-0:1.0: USB hub found
[    7.680062] hub 2-0:1.0: 1 port detected
[    7.693868] usbcore: registered new interface driver usb-storage
[    7.701860] usbcore: registered new interface driver uas
[    7.707796] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    7.723008] init: - preinit -
[    7.828728] SQUASHFS error: xz decompression failed, data probably corrupt
[    7.835639] SQUASHFS error: squashfs_read_data failed to read block 0x2887d6
[    7.842693] SQUASHFS error: Unable to read fragment cache entry [2887d6]
[    7.849392] SQUASHFS error: Unable to read page, block 2887d6, size 197e4
[    7.856235] SQUASHFS error: Unable to read fragment cache entry [2887d6]
[    7.862946] SQUASHFS error: Unable to read page, block 2887d6, size 197e4
[    7.869775] SQUASHFS error: Unable to read fragment cache entry [2887d6]
[    7.876509] SQUASHFS error: Unable to read page, block 2887d6, size 197e4
[    7.883337] SQUASHFS error: Unable to read fragment cache entry [2887d6]
[    7.890044] SQUASHFS error: Unable to read page, block 2887d6, size 197e4
[    7.896874] SQUASHFS error: Unable to read fragment cache entry [2887d6]
[    7.903616] SQUASHFS error: Unable to read page, block 2887d6, size 197e4
[    7.910928] init: Failed to start plugd: I/O error
[    8.437676] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
[    8.446038] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[    8.454544] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[    8.612978] random: jshn: uninitialized urandom read (4 bytes read)
[    8.676542] random: jshn: uninitialized urandom read (4 bytes read)
[    8.714518] random: jshn: uninitialized urandom read (4 bytes read)
[    8.936024] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode
[    8.943109] 8021q: adding VLAN 0 to HW filter on device lan1
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[   13.112239] mount_root: loading kmods from internal overlay
[   13.154209] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[   13.162812] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[   13.827431] UBIFS (ubi0:1): Mounting in unauthenticated mode
[   13.833334] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 676
[   13.921481] UBIFS (ubi0:1): recovery needed
[   14.144458] UBIFS (ubi0:1): recovery completed
[   14.149059] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[   14.156874] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[   14.166764] UBIFS (ubi0:1): FS size: 108183552 bytes (103 MiB, 852 LEBs), journal size 5459968 bytes (5 MiB, 43 LEBs)
[   14.177337] UBIFS (ubi0:1): reserved for root: 4952683 bytes (4836 KiB)
[   14.183940] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID 87AA3BCC-AF0D-4918-9A18-0F5EDBA82050, small LPT model
[   14.196966] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[   14.217071] block: extroot: not configured
[   14.221511] UBIFS (ubi0:1): un-mount UBI device 0
[   14.226250] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" stops
[   14.248432] UBIFS (ubi0:1): Mounting in unauthenticated mode
[   14.254322] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 679
[   14.424511] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[   14.432356] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[   14.442247] UBIFS (ubi0:1): FS size: 108183552 bytes (103 MiB, 852 LEBs), journal size 5459968 bytes (5 MiB, 43 LEBs)
[   14.452825] UBIFS (ubi0:1): reserved for root: 4952683 bytes (4836 KiB)
[   14.459431] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID 87AA3BCC-AF0D-4918-9A18-0F5EDBA82050, small LPT model
[   14.895500] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[   14.913671] block: extroot: not configured
[   14.921959] mount_root: switching to ubifs overlay
[   14.942066] urandom-seed: Seeding with /etc/urandom.seed
[   15.079257] SQUASHFS error: xz decompression failed, data probably corrupt
[   15.086141] SQUASHFS error: squashfs_read_data failed to read block 0x2887d6
[   15.093181] SQUASHFS error: Unable to read fragment cache entry [2887d6]
[   15.099873] SQUASHFS error: Unable to read page, block 2887d6, size 197e4