• Zarejestrowany: 2018-09-27
  • Posty: 7

Temat: R7800 luci 19.07 r10867

zakupiłem Netgear r7800 i wgrałem mu ostatnią kompilacje luci openwrt 19.07 r10867 i chciałem go zrobić jako powtarzacz sieci wi-fi miał on być połączony siecią 5ghz
po podłączeniu urządzenie musi być w innej sieci niż główne router bo inaczej nie działa.
np:
router 1 ma ip 192.168.10.1
router 2 powtarzacz wifi musi mieć ip 192.168.11.1
czym to jest spowodowane ?
problem jest z siecią bezprzewodową trzeba zrobić kilka razy włącz i wyłącz i restart urządzenia by i ręcznie trzeba ustawić kanał np 153 by zadziała zadziałała sieć 5Ghza i gubi ustawiony kanał

2 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 115,895

Odp: R7800 luci 19.07 r10867

1. Wifi będzie miał adres z tej samej klasy co ap. Na lanie musi mieć inny, a to tylko dla własnych celów bo ten adres nie bierze udziału w całym procesie.
2. Zmień kanał na 36. Nie każdy chip/sterownik lubi taki wysokie kanały na dfs.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

3 Odpowiedź przez tomas26

  • Zarejestrowany: 2018-09-27
  • Posty: 7

Odp: R7800 luci 19.07 r10867

Ok spróbuję na niższych kanałach i zobaczymy. A co do ustawienia IP w routerach by były w tej samej sieci.
By mieć zdalny dostęp do powtarzać. Bo jak jest w innej podsieci to niema dostępu zdalnego i internet jest a jak są w tej samej to niema . Chciałbym by to tak wyglądało po LAN  :

192.168.10.10 router 1
192.168.10.12 router 2 repeater

Ta sama sytuacja jest na moim TP-LINK wdr 7500v3 też nie da się ustawić by był w tej samej sieci lan.

4 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 115,895

Odp: R7800 luci 19.07 r10867

No właśnie tak to działa - wszystko ma jednakową adresację. Czytaj http://eko.one.pl/?p=openwrt-sta#mostbezprzewodowy

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

5 Odpowiedź przez tomas26

  • Zarejestrowany: 2018-09-27
  • Posty: 7

Odp: R7800 luci 19.07 r10867

takie cuda na sieci bezprzewodowe
https://naforum.zapodaj.net/thumbs/096875bd3887.jpg

jeszcze Maksymalna moc nadawania jak ustawiasz recznie na 5ghz to pokazuje 30dbm i wtedy radia nie działają bo powinny chyba mieć 23dbm,  te ustawienia są od sieci 2.4ghz tam działa prawidłowo na 30dbm

6 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 115,895

Odp: R7800 luci 19.07 r10867

Coś zepsułeś w konfigu, np. nie masz jakiegoś apostrofu bo luci nie potrafi przetrawić. Zrób uci show i znajdź błąd.
I mocy nie ustawia się na 5GHz, chyba chciałeś napisać 5dBm.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

7 Odpowiedź przez Skubi (edytowany przez Skubi 2020-09-15 17:37:36)

  • Skubi
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2011-12-08
  • Posty: 145

Odp: R7800 luci 19.07 r10867

Mam pytanie. Pozwolę sobie skorzystać z tego tematu.
Wrzuciłem ostatnie luci z eko na R7800 i próbuję skonfigurować wifi.
Zależałoby mi na sieci 2.4GHz oraz (w tej samej nazwie) na 5GHz.
Aktualnie nie wiem czego, ale 5GHz nie startuje. Proszę o pomoc

8 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 115,895

Odp: R7800 luci 19.07 r10867

Pokaż konfig i logi.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

9 Odpowiedź przez Skubi

  • Skubi
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2011-12-08
  • Posty: 145

Odp: R7800 luci 19.07 r10867

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.14.195 (cezary@eko.one.pl) (gcc version 7.5.0 (OpenWrt GCC 7.5.0 r10707-75d11f665c)) #0 SMP Thu Sep 3 22:41:56 2020
[    0.000000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5787d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[    0.000000] OF: fdt: Machine model: Netgear Nighthawk X4S R7800
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] On node 0 totalpages: 122880
[    0.000000] free_area_init_node: node 0, pgdat c0a27880, node_mem_map dda39000
[    0.000000]   Normal zone: 960 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 122880 pages, LIFO batch:31
[    0.000000] random: get_random_bytes called from 0xc09008e0 with crng_init=0
[    0.000000] percpu: Embedded 15 pages/cpu s29388 r8192 d23860 u61440
[    0.000000] pcpu-alloc: s29388 r8192 d23860 u61440 alloc=15*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 121920
[    0.000000] Kernel command line: 
[    0.000000] Bootloader command line (ignored): console=ttyHSL1,115200n8
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 477372K/491520K available (4978K kernel code, 160K rwdata, 756K rodata, 1024K init, 235K bss, 14148K reserved, 0K cma-reserved, 0K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xde800000 - 0xff800000   ( 528 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xde000000   ( 480 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0208000 - 0xc07dc880   (5971 kB)
[    0.000000]       .init : 0xc0900000 - 0xc0a00000   (1024 kB)
[    0.000000]       .data : 0xc0a00000 - 0xc0a28180   ( 161 kB)
[    0.000000]        .bss : 0xc0a2a000 - 0xc0a64e18   ( 236 kB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] clocksource: dg_timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 305801671480 ns
[    0.000006] sched_clock: 32 bits at 6MHz, resolution 160ns, wraps every 343597383600ns
[    0.000023] Switching to timer-based delay loop, resolution 160ns
[    0.000233] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.50 BogoMIPS (lpj=62500)
[    0.000260] pid_max: default: 32768 minimum: 301
[    0.000386] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000404] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000967] CPU: Testing write buffer coherency: ok
[    0.001732] Setting up static identity map for 0x42300000 - 0x42300060
[    0.001888] Hierarchical SRCU implementation.
[    0.002617] smp: Bringing up secondary CPUs ...
[    0.004446] smp: Brought up 1 node, 2 CPUs
[    0.004463] SMP: Total of 2 processors activated (25.00 BogoMIPS).
[    0.004474] CPU: All CPU(s) started in SVC mode.
[    0.014652] VFP support v0.3: implementor 51 architecture 64 part 4d variant 2 rev 0
[    0.014823] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.014849] futex hash table entries: 512 (order: 3, 32768 bytes)
[    0.014949] pinctrl core: initialized pinctrl subsystem
[    0.015929] NET: Registered protocol family 16
[    0.016186] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.017486] cpuidle: using governor ladder
[    0.017553] cpuidle: using governor menu
[    0.040123] msm_bus_fabric_init_driver
[    0.041629] usbcore: registered new interface driver usbfs
[    0.041706] usbcore: registered new interface driver hub
[    0.041792] usbcore: registered new device driver usb
[    0.041847] pps_core: LinuxPPS API ver. 1 registered
[    0.041859] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.041891] PTP clock support registered
[    0.043583] clocksource: Switched to clocksource dg_timer
[    0.046687] NET: Registered protocol family 2
[    0.047291] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[    0.047330] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[    0.047385] TCP: Hash tables configured (established 4096 bind 4096)
[    0.047480] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.047506] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.047687] NET: Registered protocol family 1
[    0.047734] PCI: CLS 0 bytes, default 64
[    0.048865] No memory allocated for crashlog
[    0.049164] workingset: timestamp_bits=30 max_order=17 bucket_order=0
[    0.053947] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.053965] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.060511] io scheduler noop registered
[    0.060531] io scheduler deadline registered (default)
[    0.062191] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda not found, using dummy regulator
[    0.062299] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda_phy not found, using dummy regulator
[    0.062395] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda_refclk not found, using dummy regulator
[    0.063165] OF: PCI: host bridge /soc/pci@1b500000 ranges:
[    0.063208] OF: PCI:    IO 0x0fe00000..0x0fefffff -> 0x0fe00000
[    0.063233] OF: PCI:   MEM 0x08000000..0x0fdfffff -> 0x08000000
[    0.171366] qcom-pcie 1b500000.pci: link up
[    0.171535] qcom-pcie 1b500000.pci: PCI host bridge to bus 0000:00
[    0.171558] pci_bus 0000:00: root bus resource [bus 00-ff]
[    0.171578] pci_bus 0000:00: root bus resource [io  0x0000-0xfffff] (bus address [0xfe00000-0xfefffff])
[    0.171592] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fdfffff]
[    0.171609] pci_bus 0000:00: scanning bus
[    0.171660] pci 0000:00:00.0: [17cb:0101] type 01 class 0x060400
[    0.171749] pci 0000:00:00.0: calling 0xc030d3c0
[    0.171823] pci 0000:00:00.0: supports D1
[    0.171832] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[    0.171849] pci 0000:00:00.0: PME# disabled
[    0.172101] pci_bus 0000:00: fixups for bus
[    0.172125] PCI: bus0: Fast back to back transfers disabled
[    0.172147] pci 0000:00:00.0: scanning [bus 01-ff] behind bridge, pass 0
[    0.172270] pci_bus 0000:01: scanning bus
[    0.172448] pci 0000:01:00.0: [168c:0046] type 00 class 0x028000
[    0.172797] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[    0.173261] pci 0000:01:00.0: calling 0xc030d3c0
[    0.174007] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[    0.174048] pci 0000:01:00.0: PME# disabled
[    0.174372] pci_bus 0000:01: fixups for bus
[    0.174442] PCI: bus1: Fast back to back transfers disabled
[    0.174457] pci_bus 0000:01: bus scan returning with max=01
[    0.174476] pci 0000:00:00.0: scanning [bus 01-ff] behind bridge, pass 1
[    0.174492] pci_bus 0000:00: bus scan returning with max=ff
[    0.174540] pci 0000:00:00.0: BAR 8: assigned [mem 0x08000000-0x081fffff]
[    0.174564] pci 0000:01:00.0: BAR 0: assigned [mem 0x08000000-0x081fffff 64bit]
[    0.174690] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[    0.174713] pci 0000:00:00.0:   bridge window [mem 0x08000000-0x081fffff]
[    0.174744] pci 0000:00:00.0: calling 0xc055ff28
[    0.174935] pcieport 0000:00:00.0: assign IRQ: got 67
[    0.175244] pcieport 0000:00:00.0: AER enabled with IRQ 35
[    0.175358] pci 0000:01:00.0: calling 0xc055ff28
[    0.175762] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda not found, using dummy regulator
[    0.175868] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda_phy not found, using dummy regulator
[    0.175962] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda_refclk not found, using dummy regulator
[    0.176709] OF: PCI: host bridge /soc/pci@1b700000 ranges:
[    0.176745] OF: PCI:    IO 0x31e00000..0x31efffff -> 0x31e00000
[    0.176769] OF: PCI:   MEM 0x2e000000..0x31dfffff -> 0x2e000000
[    0.286609] qcom-pcie 1b700000.pci: link up
[    0.286767] qcom-pcie 1b700000.pci: PCI host bridge to bus 0001:00
[    0.286786] pci_bus 0001:00: root bus resource [bus 00-ff]
[    0.286801] pci_bus 0001:00: root bus resource [mem 0x2e000000-0x31dfffff]
[    0.286814] pci_bus 0001:00: scanning bus
[    0.286858] pci 0001:00:00.0: [17cb:0101] type 01 class 0x060400
[    0.286933] pci 0001:00:00.0: calling 0xc030d3c0
[    0.286996] pci 0001:00:00.0: supports D1
[    0.287006] pci 0001:00:00.0: PME# supported from D0 D1 D3hot
[    0.287020] pci 0001:00:00.0: PME# disabled
[    0.287248] pci_bus 0001:00: fixups for bus
[    0.287266] PCI: bus0: Fast back to back transfers disabled
[    0.287284] pci 0001:00:00.0: scanning [bus 01-ff] behind bridge, pass 0
[    0.287396] pci_bus 0001:01: scanning bus
[    0.287584] pci 0001:01:00.0: [168c:0046] type 00 class 0x028000
[    0.287955] pci 0001:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[    0.288452] pci 0001:01:00.0: calling 0xc030d3c0
[    0.289143] pci 0001:01:00.0: PME# supported from D0 D3hot D3cold
[    0.289187] pci 0001:01:00.0: PME# disabled
[    0.289527] pci_bus 0001:01: fixups for bus
[    0.289606] PCI: bus1: Fast back to back transfers disabled
[    0.289622] pci_bus 0001:01: bus scan returning with max=01
[    0.289639] pci 0001:00:00.0: scanning [bus 01-ff] behind bridge, pass 1
[    0.289655] pci_bus 0001:00: bus scan returning with max=ff
[    0.289691] pci 0001:00:00.0: BAR 8: assigned [mem 0x2e000000-0x2e1fffff]
[    0.289713] pci 0001:01:00.0: BAR 0: assigned [mem 0x2e000000-0x2e1fffff 64bit]
[    0.289846] pci 0001:00:00.0: PCI bridge to [bus 01-ff]
[    0.289865] pci 0001:00:00.0:   bridge window [mem 0x2e000000-0x2e1fffff]
[    0.289892] pci 0001:00:00.0: calling 0xc055ff28
[    0.290068] pcieport 0001:00:00.0: assign IRQ: got 100
[    0.290331] pcieport 0001:00:00.0: AER enabled with IRQ 68
[    0.290441] pci 0001:01:00.0: calling 0xc055ff28
[    0.292688] L2 @ QSB rate. Forcing new rate.
[    0.292901] L2 @ 384000 KHz
[    0.293075] CPU0 @ 800000 KHz
[    0.293088] CPU1 @ QSB rate. Forcing new rate.
[    0.293214] CPU1 @ 384000 KHz
[    0.297201] gsbi 16300000.gsbi: GSBI port protocol: 6 crci: 0
[    0.299149] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.301648] msm_serial 16340000.serial: msm_serial: detected port #0
[    0.301750] msm_serial 16340000.serial: uartclk = 7372800
[    0.301832] 16340000.serial: ttyMSM0 at MMIO 0x16340000 (irq = 101, base_baud = 460800) is a MSM
[    0.301871] msm_serial: console setup on port #0
[    1.021612] console [ttyMSM0] enabled
[    1.026382] msm_serial: driver initialized
[    1.034830] loop: module loaded
[    1.036850] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xa1
[    1.036888] nand: Macronix MX30UF1G18AC
[    1.043380] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    1.047146] 8 fixed-partitions partitions found on MTD device qcom_nand.0
[    1.054676] Creating 8 MTD partitions on "qcom_nand.0":
[    1.061441] 0x000000000000-0x000000c80000 : "qcadata"
[    1.071461] random: fast init done
[    1.089080] 0x000000c80000-0x000001180000 : "APPSBL"
[    1.098440] 0x000001180000-0x000001200000 : "APPSBLENV"
[    1.100052] 0x000001200000-0x000001340000 : "art"
[    1.105316] 0x000001340000-0x000001480000 : "artbak"
[    1.110210] 0x000001480000-0x000001880000 : "kernel"
[    1.119997] 0x000001880000-0x000007900000 : "ubi"
[    1.286949] 0x000007900000-0x000008000000 : "reserve"
[    1.300961] libphy: GPIO Bitbanged MDIO: probed
[    1.322453] switch0: Atheros AR8337 rev. 2 switch registered on gpio-0
[    2.185835] ar8327: qca,phy-rgmii-en is not specified
[    2.186226] libphy: Fixed MDIO Bus: probed
[    2.192051] ipq806x-gmac-dwmac 37200000.ethernet: PTP uses main clock
[    2.194290] stmmac - user ID: 0x10, Synopsys ID: 0x37
[    2.200376] ipq806x-gmac-dwmac 37200000.ethernet: Ring mode enabled
[    2.205509] ipq806x-gmac-dwmac 37200000.ethernet: DMA HW capability register supported
[    2.211490] ipq806x-gmac-dwmac 37200000.ethernet: Enhanced/Alternate descriptors
[    2.219549] ipq806x-gmac-dwmac 37200000.ethernet: Enabled extended descriptors
[    2.227111] ipq806x-gmac-dwmac 37200000.ethernet: RX Checksum Offload Engine supported
[    2.234139] ipq806x-gmac-dwmac 37200000.ethernet: COE Type 2
[    2.241956] ipq806x-gmac-dwmac 37200000.ethernet: TX Checksum insertion supported
[    2.247854] ipq806x-gmac-dwmac 37200000.ethernet: Wake-Up On Lan supported
[    2.255231] ipq806x-gmac-dwmac 37200000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[    2.263527] ipq806x-gmac-dwmac 37400000.ethernet: PTP uses main clock
[    2.270800] stmmac - user ID: 0x10, Synopsys ID: 0x37
[    2.276940] ipq806x-gmac-dwmac 37400000.ethernet: Ring mode enabled
[    2.281886] ipq806x-gmac-dwmac 37400000.ethernet: DMA HW capability register supported
[    2.288027] ipq806x-gmac-dwmac 37400000.ethernet: Enhanced/Alternate descriptors
[    2.296025] ipq806x-gmac-dwmac 37400000.ethernet: Enabled extended descriptors
[    2.303503] ipq806x-gmac-dwmac 37400000.ethernet: RX Checksum Offload Engine supported
[    2.310615] ipq806x-gmac-dwmac 37400000.ethernet: COE Type 2
[    2.318485] ipq806x-gmac-dwmac 37400000.ethernet: TX Checksum insertion supported
[    2.324328] ipq806x-gmac-dwmac 37400000.ethernet: Wake-Up On Lan supported
[    2.331626] ipq806x-gmac-dwmac 37400000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[    2.339149] i2c /dev entries driver
[    2.347951] Calibration not found.
[    2.351359] Speed bin: 0
[    2.353666] PVS bin: 4
[    2.357747] cpuidle: enable-method property 'qcom,kpss-acc-v1' found operations
[    2.358600] cpuidle: enable-method property 'qcom,kpss-acc-v1' found operations
[    2.366392] sdhci: Secure Digital Host Controller Interface driver
[    2.373028] sdhci: Copyright(c) Pierre Ossman
[    2.379340] sdhci-pltfm: SDHCI platform and OF driver helper
[    2.385086] NET: Registered protocol family 10
[    2.390791] Segment Routing with IPv6
[    2.393758] NET: Registered protocol family 17
[    2.397583] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    2.402379] 8021q: 802.1Q VLAN Support v1.8
[    2.414998] Registering SWP/SWPB emulation handler
[    2.431420] qcom_rpm 108000.rpm: RPM firmware 3.0.16777364
[    2.443579] s1a: supplied by regulator-dummy
[    2.443679] s1a: Bringing 0uV into 1050000-1050000uV
[    2.447278] s1b: supplied by regulator-dummy
[    2.451917] s1b: Bringing 0uV into 1050000-1050000uV
[    2.456436] s2a: supplied by regulator-dummy
[    2.461133] s2a: Bringing 0uV into 775000-775000uV
[    2.465643] s2b: supplied by regulator-dummy
[    2.469976] s2b: Bringing 0uV into 775000-775000uV
[    2.479243] UBI: auto-attach mtd6
[    2.479273] ubi0: attaching mtd6
[    2.530711] random: crng init done
[    3.185599] ubi0: scanning is finished
[    3.195203] ubi0: attached mtd6 (name "ubi", size 96 MiB)
[    3.195225] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    3.199573] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    3.206416] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[    3.213200] ubi0: good PEBs: 771, bad PEBs: 1, corrupted PEBs: 0
[    3.220044] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[    3.226281] ubi0: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 33993610
[    3.233257] ubi0: available PEBs: 0, total reserved PEBs: 771, PEBs reserved for bad PEB handling: 19
[    3.242321] ubi0: background thread "ubi_bgt0d" started, PID 59
[    3.242925] block ubiblock0_0: created from ubi0:0(rootfs)
[    3.257270] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
[    3.262769] hctosys: unable to open rtc device (rtc0)
[    3.276409] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[    3.279398] Freeing unused kernel memory: 1024K
[    3.655334] init: Console is alive
[    3.655456] init: - watchdog -
[    4.601678] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    4.649746] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    4.651384] SCSI subsystem initialized
[    4.657268] libata version 3.00 loaded.
[    4.659136] ahci 29000000.sata: forcing port_map 0x0 -> 0x1
[    4.659180] ahci 29000000.sata: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode
[    4.664474] ahci 29000000.sata: flags: ncq sntf pm led clo only pmp pio slum part ccc apst 
[    4.673480] scsi host0: ahci
[    4.681381] ata1: SATA max UDMA/133 mmio [mem 0x29000000-0x2900017f] port 0x100 irq 26
[    5.016390] ata1: SATA link down (SStatus 0 SControl 300)
[    5.019817] ehci-platform: EHCI generic platform driver
[    5.026968] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    5.027938] ohci-platform: OHCI generic platform driver
[    5.162484] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[    5.162569] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[    5.167296] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000000002010010
[    5.174601] xhci-hcd xhci-hcd.0.auto: irq 105, io mem 0x11000000
[    5.184572] hub 1-0:1.0: USB hub found
[    5.190074] hub 1-0:1.0: 1 port detected
[    5.193856] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[    5.197755] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[    5.202981] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0  SuperSpeed
[    5.210691] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[    5.217502] hub 2-0:1.0: USB hub found
[    5.225543] hub 2-0:1.0: 1 port detected
[    5.229243] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[    5.233110] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
[    5.238593] xhci-hcd xhci-hcd.1.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000000002010010
[    5.246034] xhci-hcd xhci-hcd.1.auto: irq 106, io mem 0x10000000
[    5.255755] hub 3-0:1.0: USB hub found
[    5.261597] hub 3-0:1.0: 1 port detected
[    5.265819] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[    5.269241] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
[    5.274628] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0  SuperSpeed
[    5.282254] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[    5.289274] hub 4-0:1.0: USB hub found
[    5.297079] hub 4-0:1.0: 1 port detected
[    5.302882] usbcore: registered new interface driver usb-storage
[    5.305279] usbcore: registered new interface driver uas
[    5.310690] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    5.316862] init: - preinit -
[    7.601780] Generic PHY fixed-0:01: attached PHY driver [Generic PHY] (mii_bus:phy_addr=fixed-0:01, irq=POLL)
[    7.603805] dwmac1000: Master AXI performs any burst length
[    7.610802] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
[    7.616429] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
[    7.626376] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[    8.634634] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[    8.634732] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[   10.760320] mount_root: loading kmods from internal overlay
[   10.783525] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[   10.786844] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[   10.834241] print_req_error: I/O error, dev mtdblock0, sector 0
[   10.834839] print_req_error: I/O error, dev mtdblock0, sector 8
[   10.839532] print_req_error: I/O error, dev mtdblock0, sector 16
[   10.845524] print_req_error: I/O error, dev mtdblock0, sector 24
[   10.851732] print_req_error: I/O error, dev mtdblock0, sector 0
[   10.857115] Buffer I/O error on dev mtdblock0, logical block 0, async page read
[   10.919764] print_req_error: I/O error, dev mtdblock0, sector 0
[   10.919791] Buffer I/O error on dev mtdblock0, logical block 0, async page read
[   10.934129] print_req_error: I/O error, dev mtdblock1, sector 0
[   10.944150] print_req_error: I/O error, dev mtdblock1, sector 8
[   10.974047] print_req_error: I/O error, dev mtdblock1, sector 16
[   10.974569] print_req_error: I/O error, dev mtdblock1, sector 24
[   10.979539] Buffer I/O error on dev mtdblock1, logical block 0, async page read
[   10.987557] Buffer I/O error on dev mtdblock1, logical block 0, async page read
[   11.161283] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 144
[   11.210445] UBIFS (ubi0:1): recovery needed
[   11.323942] UBIFS (ubi0:1): recovery completed
[   11.324012] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[   11.327318] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[   11.335239] UBIFS (ubi0:1): FS size: 87359488 bytes (83 MiB, 688 LEBs), journal size 4317184 bytes (4 MiB, 34 LEBs)
[   11.345137] UBIFS (ubi0:1): reserved for root: 4126204 bytes (4029 KiB)
[   11.355386] UBIFS (ubi0:1): media format: w4/r0 (latest is w5/r0), UUID D693B0B4-5F2C-4317-890E-109DACF25D5F, small LPT model
[   11.364291] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[   11.379285] block: extroot: not configured
[   11.424369] UBIFS (ubi0:1): un-mount UBI device 0
[   11.424449] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" stops
[   11.444203] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 145
[   11.555130] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[   11.555153] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[   11.561933] UBIFS (ubi0:1): FS size: 87359488 bytes (83 MiB, 688 LEBs), journal size 4317184 bytes (4 MiB, 34 LEBs)
[   11.571901] UBIFS (ubi0:1): reserved for root: 4126204 bytes (4029 KiB)
[   11.582140] UBIFS (ubi0:1): media format: w4/r0 (latest is w5/r0), UUID D693B0B4-5F2C-4317-890E-109DACF25D5F, small LPT model
[   11.593322] mount_root: loading kmods from internal overlay
[   11.633435] kmodloader: loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
[   11.635935] kmodloader: done loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
[   11.648631] Buffer I/O error on dev mtdblock0, logical block 0, async page read
[   11.652736] Buffer I/O error on dev mtdblock0, logical block 0, async page read
[   11.659052] Buffer I/O error on dev mtdblock1, logical block 0, async page read
[   11.666646] Buffer I/O error on dev mtdblock1, logical block 0, async page read
[   11.859044] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[   11.863270] block: extroot: not configured
[   11.918111] mount_root: switching to ubifs overlay
[   11.954608] urandom-seed: Seeding with /etc/urandom.seed
[   12.153184] procd: - early -
[   12.153371] procd: - watchdog -
[   12.802118] procd: - watchdog -
[   12.802381] procd: - ubus -
[   12.965345] procd: - init -
[   13.202284] urngd: v1.0.2 started.
[   13.243661] kmodloader: loading kernel modules from /etc/modules.d/*
[   13.260299] tun: Universal TUN/TAP device driver, 1.6
[   13.263222] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   13.266376] Netfilter messages via NETLINK v0.30.
[   13.270516] ip_set: protocol 6
[   13.283074] fuse init (API version 7.26)
[   13.285601] usbcore: registered new interface driver cdc_acm
[   13.286055] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[   13.292215] usbcore: registered new interface driver cdc_wdm
[   13.300273] Loading modules backported from Linux version v4.19.137-0-gc076c79e03c6
[   13.305428] Backport generated by backports.git v4.19.137-1-0-g60c3a249
[   13.313808] ip_tables: (C) 2000-2006 Netfilter Core Team
[   13.322875] nf_conntrack version 0.5.0 (8192 buckets, 32768 max)
[   13.360436] usbcore: registered new interface driver usblp
[   13.363262] usbcore: registered new interface driver usbserial
[   13.364970] usbcore: registered new interface driver usbserial_generic
[   13.370672] usbserial: USB Serial support registered for generic
[   13.378678] wireguard: WireGuard 1.0.20200611 loaded. See www.wireguard.com for information.
[   13.383302] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
[   13.397647] xt_time: kernel timezone is -0000
[   13.401838] usbcore: registered new interface driver cdc_ether
[   13.406577] usbcore: registered new interface driver cdc_ncm
[   13.426473] usbcore: registered new interface driver huawei_cdc_ncm
[   13.438844] PPP generic driver version 2.4.2
[   13.439452] NET: Registered protocol family 24
[   13.442847] usbcore: registered new interface driver qmi_wwan
[   13.447491] usbcore: registered new interface driver rndis_host
[   13.452796] usbcore: registered new interface driver sierra
[   13.458120] usbserial: USB Serial support registered for Sierra USB modem
[   13.464398] usbcore: registered new interface driver sierra_net
[   13.478297] ath10k_pci 0000:01:00.0: assign IRQ: got 67
[   13.478646] ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142)
[   13.478724] ath10k_pci 0000:01:00.0: enabling bus mastering
[   13.479171] ath10k_pci 0000:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[   13.652151] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA9984/hw1.0/firmware-6.bin failed with error -2
[   13.652209] ath10k_pci 0000:01:00.0: Falling back to user helper
[   13.681887] firmware ath10k!QCA9984!hw1.0!firmware-6.bin: firmware_loading_store: map pages failed
[   14.006931] ath10k_pci 0000:01:00.0: Unknown FW IE: 30
[   14.006960] ath10k_pci 0000:01:00.0: qca9984/qca9994 hw1.0 target 0x01000000 chip_id 0x00000000 sub 168c:cafe
[   14.010962] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
[   14.022804] ath10k_pci 0000:01:00.0: firmware ver 10.4b-ct-9984-fW-012-17ba98334 api 5 features mfp,peer-flow-ctrl crc32 877928bc
[   16.342682] ath10k_pci 0000:01:00.0: board_file api 2 bmi_id 0:1 crc32 85498734
[   22.262423] ath10k_pci 0000:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1
[   22.358603] ath: EEPROM regdomain: 0x0
[   22.358616] ath: EEPROM indicates default country code should be used
[   22.358626] ath: doing EEPROM country->regdmn map search
[   22.358643] ath: country maps to regdmn code: 0x3a
[   22.358657] ath: Country alpha2 being used: US
[   22.358667] ath: Regpair used: 0x3a
[   22.364209] ath10k_pci 0001:01:00.0: assign IRQ: got 100
[   22.365257] ath10k_pci 0001:01:00.0: enabling device (0140 -> 0142)
[   22.365388] ath10k_pci 0001:01:00.0: enabling bus mastering
[   22.366095] ath10k_pci 0001:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[   22.537243] ath10k_pci 0001:01:00.0: Direct firmware load for ath10k/QCA9984/hw1.0/firmware-6.bin failed with error -2
[   22.537275] ath10k_pci 0001:01:00.0: Falling back to user helper
[   22.775184] firmware ath10k!QCA9984!hw1.0!firmware-6.bin: firmware_loading_store: map pages failed
[   22.775337] ath10k_pci 0001:01:00.0: Unknown FW IE: 30
[   22.783038] ath10k_pci 0001:01:00.0: qca9984/qca9994 hw1.0 target 0x01000000 chip_id 0x00000000 sub 168c:cafe
[   22.788248] ath10k_pci 0001:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
[   22.800162] ath10k_pci 0001:01:00.0: firmware ver 10.4b-ct-9984-fW-012-17ba98334 api 5 features mfp,peer-flow-ctrl crc32 877928bc
[   25.125956] ath10k_pci 0001:01:00.0: board_file api 2 bmi_id 0:2 crc32 85498734
[   31.057420] ath10k_pci 0001:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1
[   31.148619] ath: EEPROM regdomain: 0x0
[   31.148632] ath: EEPROM indicates default country code should be used
[   31.148643] ath: doing EEPROM country->regdmn map search
[   31.148661] ath: country maps to regdmn code: 0x3a
[   31.148674] ath: Country alpha2 being used: US
[   31.148683] ath: Regpair used: 0x3a
[   31.156153] usbcore: registered new interface driver cdc_mbim
[   31.157854] usbcore: registered new interface driver option
[   31.161030] usbserial: USB Serial support registered for GSM modem (1-port)
[   31.168584] usbcore: registered new interface driver qcserial
[   31.173268] usbserial: USB Serial support registered for Qualcomm USB modem
[   31.179327] kmodloader: done loading kernel modules from /etc/modules.d/*
[   34.088236] print_req_error: 14 callbacks suppressed
[   34.088241] print_req_error: I/O error, dev mtdblock0, sector 0
[   34.092660] print_req_error: I/O error, dev mtdblock0, sector 8
[   34.098403] print_req_error: I/O error, dev mtdblock0, sector 16
[   34.104287] print_req_error: I/O error, dev mtdblock0, sector 24
[   34.113685] print_req_error: I/O error, dev mtdblock0, sector 0
[   34.116052] Buffer I/O error on dev mtdblock0, logical block 0, async page read
[   34.125335] print_req_error: I/O error, dev mtdblock0, sector 0
[   34.128988] Buffer I/O error on dev mtdblock0, logical block 0, async page read
[   34.138139] print_req_error: I/O error, dev mtdblock1, sector 0
[   34.142597] print_req_error: I/O error, dev mtdblock1, sector 8
[   34.148583] print_req_error: I/O error, dev mtdblock1, sector 16
[   34.154476] print_req_error: I/O error, dev mtdblock1, sector 24
[   34.171981] Buffer I/O error on dev mtdblock1, logical block 0, async page read
[   34.174441] Buffer I/O error on dev mtdblock1, logical block 0, async page read
[   34.995794] Generic PHY fixed-0:01: attached PHY driver [Generic PHY] (mii_bus:phy_addr=fixed-0:01, irq=POLL)
[   34.996460] dwmac1000: Master AXI performs any burst length
[   35.004742] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
[   35.010136] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
[   35.019269] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[   35.121623] br-lan: port 1(eth1.1) entered blocking state
[   35.121648] br-lan: port 1(eth1.1) entered disabled state
[   35.126234] device eth1.1 entered promiscuous mode
[   35.131376] device eth1 entered promiscuous mode
[   35.137055] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   35.149485] Generic PHY fixed-0:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=fixed-0:00, irq=POLL)
[   35.150172] dwmac1000: Master AXI performs any burst length
[   35.158446] ipq806x-gmac-dwmac 37200000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
[   35.163973] ipq806x-gmac-dwmac 37200000.ethernet eth0: registered PTP clock
[   35.173165] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   35.834861] ath: EEPROM regdomain: 0x8268
[   35.834881] ath: EEPROM indicates we should expect a country code
[   35.837861] ath: doing EEPROM country->regdmn map search
[   35.844011] ath: country maps to regdmn code: 0x37
[   35.849299] ath: Country alpha2 being used: PL
[   35.853961] ath: Regpair used: 0x37
[   35.858324] ath: regdomain 0x8268 dynamically updated by user
[   35.861734] ath: EEPROM regdomain: 0x8268
[   35.867674] ath: EEPROM indicates we should expect a country code
[   35.871609] ath: doing EEPROM country->regdmn map search
[   35.877770] ath: country maps to regdmn code: 0x37
[   35.883067] ath: Country alpha2 being used: PL
[   35.887731] ath: Regpair used: 0x37
[   35.892092] ath: regdomain 0x8268 dynamically updated by user
[   36.074091] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[   36.075816] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[   36.082657] br-lan: port 1(eth1.1) entered blocking state
[   36.088113] br-lan: port 1(eth1.1) entered forwarding state
[   36.095547] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   36.243977] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[   36.244022] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   36.518423] pppoe-wan: renamed from ppp0
[   43.648246] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   49.902984] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[   49.924556] br-lan: port 2(wlan1) entered blocking state
[   49.924579] br-lan: port 2(wlan1) entered disabled state
[   49.929112] device wlan1 entered promiscuous mode
[   49.934377] br-lan: port 2(wlan1) entered blocking state
[   49.938825] br-lan: port 2(wlan1) entered forwarding state
[   49.944464] br-lan: port 2(wlan1) entered disabled state
[   49.949643] br-lan: port 3(wlan0) entered blocking state
[   49.955086] br-lan: port 3(wlan0) entered disabled state
[   49.960425] device wlan0 entered promiscuous mode
[   50.324173] device wlan0 left promiscuous mode
[   50.324396] br-lan: port 3(wlan0) entered disabled state
[   50.408037] ath10k_pci 0000:01:00.0: peer-unmap-event: unknown peer id 0
[   56.663306] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   56.701681] br-lan: port 3(wlan0) entered blocking state
[   56.701712] br-lan: port 3(wlan0) entered disabled state
[   56.706385] device wlan0 entered promiscuous mode
[   57.058120] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[   57.058419] br-lan: port 2(wlan1) entered blocking state
[   57.063554] br-lan: port 2(wlan1) entered forwarding state

config wifi-device 'radio0'
    option type 'mac80211'
    option hwmode '11a'
    option path 'soc/1b500000.pci/pci0000:00/0000:00:00.0/0000:01:00.0'
    option country 'PL'
    option htmode 'VHT160'
    option channel '36'

config wifi-iface 'default_radio0'
    option device 'radio0'
    option network 'lan'
    option mode 'ap'
    option key '******'
    option ssid 'Siecname'
    option encryption 'psk2'

config wifi-device 'radio1'
    option type 'mac80211'
    option hwmode '11g'
    option path 'soc/1b700000.pci/pci0001:00/0001:00:00.0/0001:01:00.0'
    option country 'PL'
    option htmode 'HT40'
    option txpower '20'
    option channel '9'

config wifi-iface 'default_radio1'
    option device 'radio1'
    option network 'lan'
    option mode 'ap'
    option key '********'
    option ssid 'Siecname'
    option encryption 'psk2'

10 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 115,895

Odp: R7800 luci 19.07 r10867

Pokaż też

iw dev

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

11 Odpowiedź przez Skubi

  • Skubi
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2011-12-08
  • Posty: 145

Odp: R7800 luci 19.07 r10867

root@LuCi:~# iw dev
phy#1
        Interface wlan1
                ifindex 11
                wdev 0x100000002
                addr 3c:37:86:2a:cf:6f
                ssid Not4u
                type AP
                channel 9 (2452 MHz), width: 20 MHz, center1: 2452 MHz
                txpower 20.00 dBm
                multicast TXQ:
                        qsz-byt qsz-pkt flows   drops   marks   overlmt hashcolt                                                                                                                                                             x-bytes tx-packets
                        0       0       3081    0       0       0       0      5                                                                                                                                                             92085           3081
phy#0
        Interface wlan0
                ifindex 12
                wdev 0x2
                addr 3c:37:86:2a:cf:6e
                type AP
                txpower 0.00 dBm
                multicast TXQ:
                        qsz-byt qsz-pkt flows   drops   marks   overlmt hashcolt                                                                                                                                                             x-bytes tx-packets
                        0       0       0       0       0       0       0      0                                                                                                                                                             0

12 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 115,895

Odp: R7800 luci 19.07 r10867

Przełącz na vht80 i uruchom wifi jeszcze raz.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

13 Odpowiedź przez Skubi

  • Skubi
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2011-12-08
  • Posty: 145

Odp: R7800 luci 19.07 r10867

Faktycznie pomogło i jedno urządzenie połączyło się z 5GHz. Akurat w PC mam kartę 160MHz - nie da sie nic z tym zrobic?
Na jakim kanale i z jakimi ustawieniami najlepiej ustawić oba połączenia?

14 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 115,895

Odp: R7800 luci 19.07 r10867

to zrób iw list i zobacz czy r7800 wspiera w ogóle 160MHz szerokość kanału.

Zostaw 36 tak jak jest.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

15 Odpowiedź przez Skubi

  • Skubi
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2011-12-08
  • Posty: 145

Odp: R7800 luci 19.07 r10867

Output z iw list:

root@LuCi:~# iw list
Wiphy phy1
        max # scan SSIDs: 16
        max scan IEs length: 209 bytes
        max # sched scan SSIDs: 0
        max # match sets: 0
        max # scan plans: 1
        max scan plan interval: -1
        max scan plan iterations: 0
        Retry short limit: 7
        Retry long limit: 4
        Coverage class: 0 (up to 0m)
        Device supports AP-side u-APSD.
        Available Antennas: TX 0xf RX 0xf
        Configured Antennas: TX 0xf RX 0xf
        Supported interface modes:
                 * managed
                 * AP
                 * monitor
                 * mesh point
                 * P2P-client
                 * P2P-GO
                 * P2P-device
        Band 1:
                Capabilities: 0x19ef
                        RX LDPC
                        HT20/HT40
                        SM Power Save disabled
                        RX HT20 SGI
                        RX HT40 SGI
                        TX STBC
                        RX STBC 1-stream
                        Max AMSDU length: 7935 bytes
                        DSSS/CCK HT40
                Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
                Minimum RX AMPDU time spacing: 8 usec (0x06)
                HT TX/RX MCS rate indexes supported: 0-31
                Frequencies:
                        * 2412 MHz [1] (20.0 dBm)
                        * 2417 MHz [2] (20.0 dBm)
                        * 2422 MHz [3] (20.0 dBm)
                        * 2427 MHz [4] (20.0 dBm)
                        * 2432 MHz [5] (20.0 dBm)
                        * 2437 MHz [6] (20.0 dBm)
                        * 2442 MHz [7] (20.0 dBm)
                        * 2447 MHz [8] (20.0 dBm)
                        * 2452 MHz [9] (20.0 dBm)
                        * 2457 MHz [10] (20.0 dBm)
                        * 2462 MHz [11] (20.0 dBm)
                        * 2467 MHz [12] (20.0 dBm)
                        * 2472 MHz [13] (20.0 dBm)
                        * 2484 MHz [14] (disabled)
        valid interface combinations:
                 * #{ managed } <= 1, #{ AP, mesh point } <= 16,
                   total <= 16, #channels <= 1, STA/AP BI must match, radar dete                                                                                                                                                             ct widths: { 20 MHz (no HT), 20 MHz, 40 MHz, 80 MHz }

        HT Capability overrides:
                 * MCS: ff ff ff ff ff ff ff ff ff ff
                 * maximum A-MSDU length
                 * supported channel width
                 * short GI for 40 MHz
                 * max A-MPDU length exponent
                 * min MPDU start spacing
        Supported extended features:
                * [ VHT_IBSS ]: VHT-IBSS
                * [ RRM ]: RRM
                * [ SET_SCAN_DWELL ]: scan dwell setting
                * [ CQM_RSSI_LIST ]: multiple CQM_RSSI_THOLD records
                * [ CONTROL_PORT_OVER_NL80211 ]: control port over nl80211
                * [ TXQS ]: FQ-CoDel-enabled intermediate TXQs
Wiphy phy0
        max # scan SSIDs: 16
        max scan IEs length: 199 bytes
        max # sched scan SSIDs: 0
        max # match sets: 0
        max # scan plans: 1
        max scan plan interval: -1
        max scan plan iterations: 0
        Retry short limit: 7
        Retry long limit: 4
        Coverage class: 0 (up to 0m)
        Device supports AP-side u-APSD.
        Available Antennas: TX 0xf RX 0xf
        Configured Antennas: TX 0xf RX 0xf
        Supported interface modes:
                 * managed
                 * AP
                 * monitor
                 * mesh point
                 * P2P-client
                 * P2P-GO
                 * P2P-device
        Band 2:
                Capabilities: 0x19ef
                        RX LDPC
                        HT20/HT40
                        SM Power Save disabled
                        RX HT20 SGI
                        RX HT40 SGI
                        TX STBC
                        RX STBC 1-stream
                        Max AMSDU length: 7935 bytes
                        DSSS/CCK HT40
                Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
                Minimum RX AMPDU time spacing: 8 usec (0x06)
                HT TX/RX MCS rate indexes supported: 0-31
                VHT Capabilities (0x339b79fa):
                        Max MPDU length: 11454
                        Supported Channel Width: 160 MHz, 80+80 MHz
                        RX LDPC
                        short GI (80 MHz)
                        short GI (160/80+80 MHz)
                        TX STBC
                        SU Beamformer
                        SU Beamformee
                        MU Beamformer
                        MU Beamformee
                        RX antenna pattern consistency
                        TX antenna pattern consistency
                VHT RX MCS set:
                        1 streams: MCS 0-9
                        2 streams: MCS 0-9
                        3 streams: MCS 0-9
                        4 streams: MCS 0-9
                        5 streams: not supported
                        6 streams: not supported
                        7 streams: not supported
                        8 streams: not supported
                VHT RX highest supported: 1560 Mbps
                VHT TX MCS set:
                        1 streams: MCS 0-9
                        2 streams: MCS 0-9
                        3 streams: MCS 0-9
                        4 streams: MCS 0-9
                        5 streams: not supported
                        6 streams: not supported
                        7 streams: not supported
                        8 streams: not supported
                VHT TX highest supported: 1560 Mbps
                Frequencies:
                        * 5180 MHz [36] (23.0 dBm)
                        * 5200 MHz [40] (23.0 dBm)
                        * 5220 MHz [44] (23.0 dBm)
                        * 5240 MHz [48] (23.0 dBm)
                        * 5260 MHz [52] (20.0 dBm) (radar detection)
                        * 5280 MHz [56] (20.0 dBm) (radar detection)
                        * 5300 MHz [60] (20.0 dBm) (radar detection)
                        * 5320 MHz [64] (20.0 dBm) (radar detection)
                        * 5500 MHz [100] (26.0 dBm) (radar detection)
                        * 5520 MHz [104] (26.0 dBm) (radar detection)
                        * 5540 MHz [108] (26.0 dBm) (radar detection)
                        * 5560 MHz [112] (26.0 dBm) (radar detection)
                        * 5580 MHz [116] (26.0 dBm) (radar detection)
                        * 5600 MHz [120] (26.0 dBm) (radar detection)
                        * 5620 MHz [124] (26.0 dBm) (radar detection)
                        * 5640 MHz [128] (26.0 dBm) (radar detection)
                        * 5660 MHz [132] (26.0 dBm) (radar detection)
                        * 5680 MHz [136] (26.0 dBm) (radar detection)
                        * 5700 MHz [140] (26.0 dBm) (radar detection)
                        * 5720 MHz [144] (disabled)
                        * 5745 MHz [149] (13.0 dBm)
                        * 5765 MHz [153] (13.0 dBm)
                        * 5785 MHz [157] (13.0 dBm)
                        * 5805 MHz [161] (13.0 dBm)
                        * 5825 MHz [165] (13.0 dBm)
                        * 5845 MHz [169] (13.0 dBm)
                        * 5865 MHz [173] (13.0 dBm)
        valid interface combinations:
                 * #{ managed } <= 1, #{ AP, mesh point } <= 16,
                   total <= 16, #channels <= 1, STA/AP BI must match, radar dete                                                                                                                                                             ct widths: { 20 MHz (no HT), 20 MHz, 40 MHz, 80 MHz }

        HT Capability overrides:
                 * MCS: ff ff ff ff ff ff ff ff ff ff
                 * maximum A-MSDU length
                 * supported channel width
                 * short GI for 40 MHz
                 * max A-MPDU length exponent
                 * min MPDU start spacing
        Supported extended features:
                * [ VHT_IBSS ]: VHT-IBSS
                * [ RRM ]: RRM
                * [ SET_SCAN_DWELL ]: scan dwell setting
                * [ CQM_RSSI_LIST ]: multiple CQM_RSSI_THOLD records
                * [ CONTROL_PORT_OVER_NL80211 ]: control port over nl80211
                * [ TXQS ]: FQ-CoDel-enabled intermediate TXQs

Sąsiadka też sieje obok 5GHz na 36 stąd zastanawiałem się czy go zmienić..

16 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 115,895

Odp: R7800 luci 19.07 r10867

Teoretycznie wspiera. Poczekaj aż inny odpowiedzą czy u nich działa vht160.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

17 Odpowiedź przez Skubi (edytowany przez Skubi 2020-09-15 18:35:57)

  • Skubi
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2011-12-08
  • Posty: 145

Odp: R7800 luci 19.07 r10867

Cezary napisał/a:

Teoretycznie wspiera. Poczekaj aż inny odpowiedzą czy u nich działa vht160.

Właśnie z tego co kojarzyłem sam router to ma obsługę VHT160 stąd wydawało mi się, że się zgrają z kartą a tu klops..

EDIT:
Znalazłem jeszcze coś ciekawego:

root@LuCi:~# iw reg get
global
country PL: DFS-ETSI
        (2400 - 2483 @ 40), (N/A, 20), (N/A)
        (5150 - 5250 @ 80), (N/A, 23), (N/A), NO-OUTDOOR, AUTO-BW
        (5250 - 5350 @ 80), (N/A, 20), (0 ms), NO-OUTDOOR, DFS, AUTO-BW
        (5470 - 5725 @ 160), (N/A, 26), (0 ms), DFS
        (5725 - 5875 @ 80), (N/A, 13), (N/A)
        (57000 - 66000 @ 2160), (N/A, 40), (N/A)

phy#1
country US: DFS-FCC
        (2402 - 2472 @ 40), (N/A, 30), (N/A)
        (5170 - 5250 @ 80), (N/A, 23), (N/A), AUTO-BW
        (5250 - 5330 @ 80), (N/A, 23), (0 ms), DFS, AUTO-BW
        (5490 - 5730 @ 160), (N/A, 23), (0 ms), DFS
        (5735 - 5835 @ 80), (N/A, 30), (N/A)
        (57240 - 71000 @ 2160), (N/A, 40), (N/A)

phy#0
country US: DFS-FCC
        (2402 - 2472 @ 40), (N/A, 30), (N/A)
        (5170 - 5250 @ 80), (N/A, 23), (N/A), AUTO-BW
        (5250 - 5330 @ 80), (N/A, 23), (0 ms), DFS, AUTO-BW
        (5490 - 5730 @ 160), (N/A, 23), (0 ms), DFS
        (5735 - 5835 @ 80), (N/A, 30), (N/A)
        (57240 - 71000 @ 2160), (N/A, 40), (N/A)

18 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 115,895

Odp: R7800 luci 19.07 r10867

I co ciekawego wg ciebie znalazłeś?

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

19 Odpowiedź przez Skubi (edytowany przez Skubi 2020-09-15 18:41:03)

  • Skubi
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2011-12-08
  • Posty: 145

Odp: R7800 luci 19.07 r10867

https://forum.openwrt.org/t/5ghz-wifi-n … h/42423/12

I coś podobnego tutaj: https://eko.one.pl/forum/viewtopic.php?id=19185 - tylko nie wiem czy to aktualne i zadziała?

20 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 115,895

Odp: R7800 luci 19.07 r10867

Śmiało , testuj.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

21 Odpowiedź przez Skubi

  • Skubi
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2011-12-08
  • Posty: 145

Odp: R7800 luci 19.07 r10867

root@LuCi:~# opkg remove kmod-ath10k
Removing package kmod-ath10k from root...
root@LuCi:~# opkg install kmod-ath10k-ct
Installing kmod-ath10k-ct (4.14.195+2019-09-09-5e8cd86f-1) to root...
Downloading http://dl.eko.one.pl/openwrt-19.07/targets/ipq806x/generic/kmods-4.14.195/kmod-ath10k-ct_4.14.195%2b2019-09-09-5e8cd86f-1_arm_cortex-a15_neon-vfpv4.ipk
Configuring kmod-ath10k-ct.
root@LuCi:~# opkg install ethtool
Installing ethtool (5.2-1) to root...
Downloading http://downloads.openwrt.org/releases/19.07-SNAPSHOT/packages/arm_cortex-a15_neon-vfpv4/base/ethtool_5.2-1_arm_cortex-a15_neon-vfpv4.ipk
Configuring ethtool.

Podmieniony plik bin z linka wyzej oraz dodane rc.local , ale niestety na VHT160 5GHz siec nie wstaje sad

22 Odpowiedź przez Skubi

  • Skubi
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2011-12-08
  • Posty: 145

Odp: R7800 luci 19.07 r10867

Ok zdaje się, że już "clou" problemu jest znany:

https://forum.openwrt.org/t/lack-of-5gh … 00/74360/9

23 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 115,895

Odp: R7800 luci 19.07 r10867

Przestaw sobie na kraj gdzie dfs nie obowiązuje (np indie), zób restart urządzenia i pewnie uruchomisz vht160 na kanałach 36-64.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

24 Odpowiedź przez Skubi

  • Skubi
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2011-12-08
  • Posty: 145

Odp: R7800 luci 19.07 r10867

root@LuCi:~# iw reg get
global
country IN: DFS-UNSET
        (2402 - 2482 @ 40), (N/A, 20), (N/A)
        (5150 - 5250 @ 80), (N/A, 30), (N/A)
        (5250 - 5350 @ 80), (N/A, 24), (N/A)
        (5470 - 5725 @ 160), (N/A, 24), (N/A)
        (5725 - 5875 @ 80), (N/A, 30), (N/A)


Dopiero po przestawieniu na Indie i ustawieniu kanału 100 sieć wstała na VHT160. Na kanale 36 niestety nie wstaje.

25 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 115,895

Odp: R7800 luci 19.07 r10867

I tak chciałeś mieć inaczej niż sąsiadka smile

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona